The HFP_HSW_HBP_HI register must be programmed with 2 LSbits of each
Horizontal Front Porch/Sync/Back Porch. Currently the driver programs
this register to 0, which breaks displays with either value above 255.
The HFP_MIN register must be set to the same value as HFP_LI, otherwise
there is visible image distortion, usually in the form of missing lines
at the bottom of the panel.
Fix this by correctly programming the HFP_HSW_HBP_HI and HFP_MIN registers.
Acked-by: Maxime Ripard <maxime@cerno.tech> Fixes: ce517f18944e3 ("drm: bridge: Add Chipone ICN6211 MIPI-DSI to RGB bridge") Signed-off-by: Marek Vasut <marex@denx.de> Cc: Jagan Teki <jagan@amarulasolutions.com> Cc: Maxime Ripard <maxime@cerno.tech> Cc: Robert Foss <robert.foss@linaro.org> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Thomas Zimmermann <tzimmermann@suse.de>
To: dri-devel@lists.freedesktop.org Signed-off-by: Robert Foss <robert.foss@linaro.org> Link: https://patchwork.freedesktop.org/patch/msgid/20220331150509.9838-3-marex@denx.de Signed-off-by: Sasha Levin <sashal@kernel.org>
The chip register layout has nothing to do with MIPI DCS, the registers
incorrectly marked as MIPI DCS in the driver are regular chip registers
often with completely different function.
Fill in the actual register names and bits from [1] and [2] and add the
entire register layout, since the documentation for this chip is hard to
come by.
Add the missing destroy_workqueue() before return from
anx7625_i2c_probe() in the error handling case.
Fixes: adca62ec370c ("drm/bridge: anx7625: Support reading edid through aux channel") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Reviewed-by: Hsin-Yi Wang <hsinyi@chromium.org> Signed-off-by: Robert Foss <robert.foss@linaro.org> Link: https://patchwork.freedesktop.org/patch/msgid/20220326073326.3389347-1-yangyingliang@huawei.com Signed-off-by: Sasha Levin <sashal@kernel.org>
The invalid EDID block filtering uses the number of valid EDID
extensions instead of all EDID extensions for looping the extensions in
the copy. This is fine, by coincidence, if all the invalid blocks are at
the end of the EDID. However, it's completely broken if there are
invalid extensions in the middle; the invalid blocks are included and
valid blocks are excluded.
Fix it by modifying the base block after, not before, the copy.
Fixes: 14544d0937bf ("drm/edid: Only print the bad edid when aborting") Reported-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Jani Nikula <jani.nikula@intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20220330170426.349248-1-jani.nikula@intel.com Signed-off-by: Sasha Levin <sashal@kernel.org>
If DRM_ITE_IT6505 is y but DRM_DP_HELPER is m, building failed:
drivers/gpu/drm/bridge/ite-it6505.o: In function `it6505_i2c_remove':
ite-it6505.c:(.text+0x35c): undefined reference to `drm_dp_aux_unregister'
drivers/gpu/drm/bridge/ite-it6505.o: In function `it6505_dpcd_read':
ite-it6505.c:(.text+0x420): undefined reference to `drm_dp_dpcd_read'
drivers/gpu/drm/bridge/ite-it6505.o: In function `it6505_get_dpcd':
ite-it6505.c:(.text+0x4a4): undefined reference to `drm_dp_dpcd_read'
drivers/gpu/drm/bridge/ite-it6505.o: In function `it6505_dpcd_write':
ite-it6505.c:(.text+0x52c): undefined reference to `drm_dp_dpcd_write'
Select DRM_DP_HELPER for DRM_ITE_IT6505 to fix this.
ath11k_peer_find_by_addr states via lockdep that ab->base_lock must be
held when calling that function in order to protect the list. All
callers except ath11k_mac_op_unassign_vif_chanctx have that lock
acquired when calling ath11k_peer_find_by_addr. That lock is also not
transitively held by a path towards ath11k_mac_op_unassign_vif_chanctx.
The solution is to acquire the lock when calling
ath11k_peer_find_by_addr inside ath11k_mac_op_unassign_vif_chanctx.
I am currently working on a static analyser to detect missing locks and
this was a reported case. I manually verified the report by looking at
the code, but I do not have real hardware so this is compile tested
only.
Fixes: 701e48a43e15 ("ath11k: add packet log support for QCA6390") Signed-off-by: Niels Dossche <dossche.niels@gmail.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20220314215253.92658-1-dossche.niels@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
vmw_move assumed that buffers to be moved would always be
vmw_buffer_object's but after introduction of new placement for mob
pages that's no longer the case.
The resulting invalid read didn't have any practical consequences
because the memory isn't used unless the object actually is a
vmw_buffer_object.
Fix it by moving the cast to the spot where the results are used.
Signed-off-by: Zack Rusin <zackr@vmware.com> Fixes: f6be23264bba ("drm/vmwgfx: Introduce a new placement for MOB page tables") Reported-by: Chuck Lever III <chuck.lever@oracle.com> Reviewed-by: Martin Krastev <krastevm@vmware.com> Tested-by: Chuck Lever <chuck.lever@oracle.com> Link: https://patchwork.freedesktop.org/patch/msgid/20220318174332.440068-2-zack@kde.org Signed-off-by: Sasha Levin <sashal@kernel.org>
Easily hit the below list corruption:
==
list_add corruption. prev->next should be next (ffffffffc0ceb090), but
was ffffec604507edc8. (prev=ffffec604507edc8).
WARNING: CPU: 65 PID: 3959 at lib/list_debug.c:26
__list_add_valid+0x53/0x80
CPU: 65 PID: 3959 Comm: fbdev Tainted: G U
RIP: 0010:__list_add_valid+0x53/0x80
Call Trace:
<TASK>
fb_deferred_io_mkwrite+0xea/0x150
do_page_mkwrite+0x57/0xc0
do_wp_page+0x278/0x2f0
__handle_mm_fault+0xdc2/0x1590
handle_mm_fault+0xdd/0x2c0
do_user_addr_fault+0x1d3/0x650
exc_page_fault+0x77/0x180
? asm_exc_page_fault+0x8/0x30
asm_exc_page_fault+0x1e/0x30
RIP: 0033:0x7fd98fc8fad1
==
Figure out the race happens when one process is adding &page->lru into
the pagelist tail in fb_deferred_io_mkwrite(), another process is
re-initializing the same &page->lru in fb_deferred_io_fault(), which is
not protected by the lock.
This fix is to init all the page lists one time during initialization,
it not only fixes the list corruption, but also avoids INIT_LIST_HEAD()
redundantly.
V2: change "int i" to "unsigned int i" (Geert Uytterhoeven)
Signed-off-by: Chuansheng Liu <chuansheng.liu@intel.com> Fixes: 105a940416fc ("fbdev/defio: Early-out if page is already enlisted") Cc: Thomas Zimmermann <tzimmermann@suse.de> Cc: Geert Uytterhoeven <geert@linux-m68k.org> Reviewed-by: Javier Martinez Canillas <javierm@redhat.com> Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de> Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de> Link: https://patchwork.freedesktop.org/patch/msgid/20220318005003.51810-1-chuansheng.liu@intel.com Signed-off-by: Sasha Levin <sashal@kernel.org>
ssd130x_clear_screen() allocates a temporary buffer sized to hold one
byte per pixel, while it only needs to hold one bit per pixel.
ssd130x_fb_blit_rect() allocates a temporary buffer sized to hold one
byte per pixel for the whole frame buffer, while it only needs to hold
one bit per pixel for the part that is to be updated.
Pass dst_pitch to drm_fb_xrgb8888_to_mono(), as we have already
calculated it anyway.
Fixes: a61732e808672cfa ("drm: Add driver for Solomon SSD130x OLED displays") Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org> Acked-by: Javier Martinez Canillas <javierm@redhat.com> Signed-off-by: Javier Martinez Canillas <javierm@redhat.com> Link: https://patchwork.freedesktop.org/patch/msgid/20220317081830.1211400-5-geert@linux-m68k.org Signed-off-by: Sasha Levin <sashal@kernel.org>
The rectangle update functions ssd130x_fb_blit_rect() and
ssd130x_update_rect() do not behave correctly when x1 != 0 or y1 !=
0, or when y1 or y2 are not aligned to display page boundaries.
E.g. when used as a text console, only the first line of text is shown
on the display.
1. The buffer passed by ssd130x_fb_blit_rect() points to the first
byte of monochrome bitmap data, and thus has its origin at (x1,
y1), while ssd130x_update_rect() assumes it is at (0, 0).
Fix ssd130x_update_rect() by changing the vertical and horizontal
loop ranges, and adding the offsets only when needed.
2. In ssd130x_fb_blit_rect(), align y1 and y2 to the display page
boundaries before doing the color conversion, so the full page
is converted and updated.
Remove the correction for an unaligned y1 from
ssd130x_update_rect(), and add a check to make sure y1 is aligned.
Fixes: a61732e808672cfa ("drm: Add driver for Solomon SSD130x OLED displays") Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org> Acked-by: Javier Martinez Canillas <javierm@redhat.com> Signed-off-by: Javier Martinez Canillas <javierm@redhat.com> Link: https://patchwork.freedesktop.org/patch/msgid/20220317081830.1211400-4-geert@linux-m68k.org Signed-off-by: Sasha Levin <sashal@kernel.org>
The conversion functions drm_fb_xrgb8888_to_mono() and
drm_fb_gray8_to_mono_line() do not behave correctly when the
horizontal boundaries of the clip rectangle are not multiples of 8:
a. When x1 % 8 != 0, the calculated pitch is not correct,
b. When x2 % 8 != 0, the pixel data for the last byte is wrong.
Simplify the code and fix (a) by:
1. Removing start_offset, and always storing the first pixel in the
first bit of the monochrome destination buffer.
Drivers that require the first pixel in a byte to be located at an
x-coordinate that is a multiple of 8 can always align the clip
rectangle before calling drm_fb_xrgb8888_to_mono().
Note that:
- The ssd130x driver does not need the alignment, as the
monochrome buffer is a temporary format,
- The repaper driver always updates the full screen, so the clip
rectangle is always aligned.
2. Passing the number of pixels to drm_fb_gray8_to_mono_line(),
instead of the number of bytes, and the number of pixels in the
last byte.
Fix (b) by explicitly setting the target bit, instead of always setting
bit 7 and shifting the value in each loop iteration.
Remove the bogus pitch check, which operates on bytes instead of pixels,
and triggers when e.g. flashing the cursor on a text console with a font
that is 8 pixels wide.
Drop the confusing comment about scanlines, as a pitch in bytes always
contains a multiple of 8 pixels.
While at it, use the drm_rect_height() helper instead of open-coding the
same operation.
Update the comments accordingly.
Fixes: bcf8b616deb87941 ("drm/format-helper: Add drm_fb_xrgb8888_to_mono_reversed()") Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org> Acked-by: Javier Martinez Canillas <javierm@redhat.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Javier Martinez Canillas <javierm@redhat.com> Link: https://patchwork.freedesktop.org/patch/msgid/20220317081830.1211400-3-geert@linux-m68k.org Signed-off-by: Sasha Levin <sashal@kernel.org>
There is no "reversed" handling in drm_fb_xrgb8888_to_mono_reversed():
the function just converts from color to grayscale, and reduces the
number of grayscale levels from 256 to 2 (i.e. brightness 0-127 is
mapped to 0, 128-255 to 1). All "reversed" handling is done in the
repaper driver, where this function originated.
Hence make this clear by renaming drm_fb_xrgb8888_to_mono_reversed() to
drm_fb_xrgb8888_to_mono(), and documenting the black/white pixel
mapping.
Fixes: bcf8b616deb87941 ("drm/format-helper: Add drm_fb_xrgb8888_to_mono_reversed()") Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org> Acked-by: Javier Martinez Canillas <javierm@redhat.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Javier Martinez Canillas <javierm@redhat.com> Link: https://patchwork.freedesktop.org/patch/msgid/20220317081830.1211400-2-geert@linux-m68k.org Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently the ssd130x driver only sets the segment remap setting when
the device tree requests it; it however does not clear the setting if
it is not requested. This leads to the setting incorrectly persisting
if the hardware is always on and has no reset GPIO wired. This might
happen when a developer is trying to find the correct settings for an
unknown module, and cause the developer to get confused because the
settings from the device tree are not consistently applied.
Make the driver apply the segment remap setting consistently, setting
the value correctly based on the device tree setting. This also makes
this setting's behavior consistent with the other settings, which are
always applied.
Fixes: a61732e80867 ("drm: Add driver for Solomon SSD130x OLED displays") Signed-off-by: Chen-Yu Tsai <wens@csie.org> Acked-by: Javier Martinez Canillas <javierm@redhat.com> Signed-off-by: Javier Martinez Canillas <javierm@redhat.com> Link: https://patchwork.freedesktop.org/patch/msgid/20220308160758.26060-2-wens@kernel.org Signed-off-by: Sasha Levin <sashal@kernel.org>
The SSD130x's command to toggle COM scan direction uses bit 3 and only
bit 3 to set the direction of the scanout. The driver has an incorrect
GENMASK(3, 2), causing the setting to be set on bit 2, rendering it
ineffective.
Fix the mask to only bit 3, so that the requested setting is applied
correctly.
The backlight property was lost during conversion to yaml in commit abdd9e3705c8 ("dt-bindings: display: sitronix,st7735r: Convert to DT schema").
Put it back.
Hotplug events reported by bridge drivers over drm_bridge_hpd_notify()
get ignored unless somebody calls drm_bridge_hpd_enable(). When the
connector for the bridge is bridge_connector, such a call is done from
drm_bridge_connector_enable_hpd().
However drm_bridge_connector_enable_hpd() is never called on init paths,
documentation suggests that it is intended for suspend/resume paths.
In result, once encoders are switched to bridge_connector,
bridge-detected HPD stops working.
This patch adds a call to that API on init path.
This fixes HDMI HPD with rcar-du + adv7513 case when adv7513 reports HPD
events via interrupts.
When building the kernel for arm with the "-mabi=apcs-gnu" option, gcc
will force alignment of all structures and unions to a word boundary
(see also STRUCTURE_SIZE_BOUNDARY and the "-mstructure-size-boundary=XX"
option if you're a gcc person), even when the members of said structures
do not want or need said alignment.
This completely messes up the structure alignment of 'struct edid' on
those targets, because even though all the embedded structures are
marked with "__attribute__((packed))", the unions that contain them are
not.
This was exposed by commit f1e4c916f97f ("drm/edid: add EDID block count
and size helpers"), but the bug is pre-existing. That commit just made
the structure layout problem cause a build failure due to the addition
of the
BUILD_BUG_ON(sizeof(*edid) != EDID_LENGTH);
sanity check in drivers/gpu/drm/drm_edid.c:edid_block_data().
This legacy union alignment should probably not be used in the first
place, but we can fix the layout by adding the packed attribute to the
union entries even when each member is already packed and it shouldn't
matter in a sane build environment.
You can see this issue with a trivial test program:
gpio_keys module can either accept gpios or interrupts. The module
initializes delayed work in case of gpios only and is only used if
debounce timer is not used, so make sure cancel_delayed_work_sync()
is called only when its gpio-backed and debounce_use_hrtimer is false.
This fixes the issue seen below when the gpio_keys module is unloaded and
an interrupt pin is used instead of GPIO:
Recent changes to multichannel to allow channel reconnects to
work in parallel and independent of each other did so by
making use of tcpStatus for the connection, and status for the
session. However, this did not take into account the multiuser
scenario, where same connection is used by multiple connections.
However, tcpStatus should be tracked only till the end of
negotiate exchange, and not used for session setup. This change
fixes this.
Signed-off-by: Shyam Prasad N <sprasad@microsoft.com> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
drivers/macintosh/via-pmu-event.o: In function `via_pmu_event':
via-pmu-event.c:(.text+0x44): undefined reference to `input_event'
via-pmu-event.c:(.text+0x68): undefined reference to `input_event'
via-pmu-event.c:(.text+0x94): undefined reference to `input_event'
via-pmu-event.c:(.text+0xb8): undefined reference to `input_event'
drivers/macintosh/via-pmu-event.o: In function `via_pmu_event_init':
via-pmu-event.c:(.init.text+0x20): undefined reference to `input_allocate_device'
via-pmu-event.c:(.init.text+0xc4): undefined reference to `input_register_device'
via-pmu-event.c:(.init.text+0xd4): undefined reference to `input_free_device'
make[1]: *** [Makefile:1155: vmlinux] Error 1
make: *** [Makefile:350: __build_one_by_one] Error 2
Don't call into the input subsystem unless CONFIG_INPUT is built-in.
Reported-by: kernel test robot <lkp@intel.com> Signed-off-by: Finn Thain <fthain@linux-m68k.org> Tested-by: Randy Dunlap <rdunlap@infradead.org> Reviewed-by: Christophe Leroy <christophe.leroy@csgroup.eu> Acked-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/5edbe76ce68227f71e09af4614cc4c1bd61c7ec8.1649326292.git.fthain@linux-m68k.org Signed-off-by: Sasha Levin <sashal@kernel.org>
In init_winctx_regs(), __pa() is called on winctx->rx_fifo and this
function is called to initialize registers for receive and fault
windows. But the real address is passed in winctx->rx_fifo for
receive windows and the virtual address for fault windows which
causes errors with DEBUG_VIRTUAL enabled. Fixes this issue by
assigning only real address to rx_fifo in vas_rx_win_attr struct
for both receive and fault windows.
Due to a typo, the final argument to alloc_page_vma() didn't refer to a
real variable. This only affected CONFIG_NUMA, which was marked BROKEN in
2006 and removed from alpha in 2021. Found due to a refactoring patch.
Link: https://lkml.kernel.org/r/20220504182857.4013401-4-willy@infradead.org Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org> Reported-by: kernel test robot <lkp@intel.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The L1 should not be able to adjust LPES mode for the L2. Setting LPES
if the L0 needs it clear would cause external interrupts to be sent to
L2 and missed by the L0.
Clearing LPES when it may be set, as typically happens with XIVE enabled
could cause a performance issue despite having no native XIVE support in
the guest, because it will cause mediated interrupts for the L2 to be
taken in HV mode, which then have to be injected.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Reviewed-by: Fabiano Rosas <farosas@linux.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20220303053315.1056880-7-npiggin@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Clear FLR (Function Level Reset) from device capabilities
registers for all physical functions.
During FLR, the Margining Lane Status and Margining Lane Control
registers should not be reset, as per PCIe specification.
However, the controller incorrectly resets these registers upon FLR.
This causes PCISIG compliance FLR test to fail. Hence preventing
all functions from advertising FLR support if flag quirk_disable_flr
is set.
The sysfs sriov_numvfs_store() path acquires the device lock before the
config space access lock:
sriov_numvfs_store
device_lock # A (1) acquire device lock
sriov_configure
vfio_pci_sriov_configure # (for example)
vfio_pci_core_sriov_configure
pci_disable_sriov
sriov_disable
pci_cfg_access_lock
pci_wait_cfg # B (4) wait for dev->block_cfg_access == 0
Previously, pci_dev_lock() acquired the config space access lock before the
device lock:
pci_dev_lock
pci_cfg_access_lock
dev->block_cfg_access = 1 # B (2) set dev->block_cfg_access = 1
device_lock # A (3) wait for device lock
Any path that uses pci_dev_lock(), e.g., pci_reset_function(), may
deadlock with sriov_numvfs_store() if the operations occur in the sequence
(1) (2) (3) (4).
Avoid the deadlock by reversing the order in pci_dev_lock() so it acquires
the device lock before the config space access lock, the same as the
sriov_numvfs_store() path.
[bhelgaas: combined and adapted commit log from Jay Zhou's independent
subsequent posting:
https://lore.kernel.org/r/20220404062539.1710-1-jianjay.zhou@huawei.com] Link: https://lore.kernel.org/linux-pci/1583489997-17156-1-git-send-email-yangyicong@hisilicon.com/ Also-posted-by: Jay Zhou <jianjay.zhou@huawei.com> Signed-off-by: Yicong Yang <yangyicong@hisilicon.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
This happens because MSR[RI] is unset when entering RTAS but there is no
valid reason to not set it here.
RTAS is expected to be called with MSR[RI] as specified in PAPR+ section
"7.2.1 Machine State":
R1–7.2.1–9. If called with MSR[RI] equal to 1, then RTAS must protect
its own critical regions from recursion by setting the MSR[RI] bit to
0 when in the critical regions.
Fixing this by reviewing the way MSR is compute before calling RTAS. Now a
hardcoded value meaning real mode, 32 bits big endian mode and Recoverable
Interrupt is loaded. In the case MSR[S] is set, it will remain set while
entering RTAS as only urfid can unset it (thanks Fabiano).
In addition a check is added in do_enter_rtas() to detect calls made with
MSR[RI] unset, as we are forcing it on later.
This patch has been tested on the following machines:
Power KVM Guest
P8 S822L (host Ubuntu kernel 5.11.0-49-generic)
PowerVM LPAR
P8 9119-MME (FW860.A1)
p9 9008-22L (FW950.00)
P10 9080-HEX (FW1010.00)
Suggested-by: Nicholas Piggin <npiggin@gmail.com> Signed-off-by: Laurent Dufour <ldufour@linux.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20220504101244.12107-1-ldufour@linux.ibm.com Signed-off-by: Sasha Levin <sashal@kernel.org>
For some platforms, the frequency returned by hardware may be slightly
different from what is provided in the frequency table. For example,
hardware may return 499 MHz instead of 500 MHz. In such cases it is
better to avoid getting into unnecessary frequency updates, as we may
end up switching policy->cur between the two and sending unnecessary
pre/post update notifications, etc.
This patch has chosen allows the hardware frequency and table frequency
to deviate by 1 MHz for now, we may want to increase it a bit later on
if someone still complains.
It will cause null-ptr-deref when using 'res', if platform_get_resource()
returns NULL, so move using 'res' after devm_ioremap_resource() that
will check it to avoid null-ptr-deref.
And use devm_platform_get_and_ioremap_resource() to simplify code.
Dump capture would fail if capture kernel is not of the endianess as the
production kernel, because the in-memory data structure (struct
opal_fadump_mem_struct) shared across production kernel and capture
kernel assumes the same endianess for both the kernels, which doesn't
have to be true always. Fix it by having a well-defined endianess for
struct opal_fadump_mem_struct.
Since its introduction to the mainline kernel, omap1_uart_recalc() helper
makes incorrect use of clk->enable_bit as a ready to use bitmap mask while
it only provides the bit number. Fix it.
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com> Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
For making easier to test, add the new quirk_flags bits 17 and 18 to
enable and disable the generic implicit feedback mode. The bit 17 is
equivalent with implicit_fb=1 option, applying the generic implicit
feedback sync mode. OTOH, the bit 18 disables the implicit fb mode
forcibly.
In our fault-injection testing, the variable "nblocks" in dbFree() can be
zero when kmalloc_array() fails in dtSearch(). In this case, the variable
"mp" in dbFree() would be NULL and then it is dereferenced in
"write_metapage(mp)".
The allocation funciton devm_kcalloc may fail and return a null pointer,
which would cause a null-pointer dereference later.
It might be better to check it and directly return -ENOMEM just like the
usage of devm_kcalloc in previous code.
Use a fine grained specification of DMA mapping directions
in certain cases, allowing both a more optimized operation
as well as shushing out a harmless, though persky
dma-debug warning.
Currently all of the quirked systems use the same card and so the
DMI quirk list doesn't contain driver data.
Add driver data to these quirks and then check the data was present
or not. This will allow potentially setting quirks for systems with
faulty firmware that claims to have a DMIC but doesn't really.
dtschema expects DMA channels in specific order (tx, rx and tx-sec).
The order actually should not matter because dma-names is used however
let's make it aligned with dtschema to suppress warnings like:
i2s@eee30000: dma-names: ['rx', 'tx', 'tx-sec'] is not valid under any of the given schemas
Intel DG2 discrete graphics PCIe endpoints advertise L1 acceptable exit
latency to be < 1us even though they can actually tolerate unlimited exit
latencies just fine. Quirk the L1 acceptable exit latency for these
endpoints to be unlimited so ASPM L1 can be enabled.
The documentation of the function rvt_error_qp says both r_lock and
s_lock need to be held when calling that function.
It also asserts using lockdep that both of those locks are held.
rvt_error_qp is called form rvt_send_cq, which is called from
rvt_qp_complete_swqe, which is called from rvt_send_complete, which is
called from rvt_ruc_loopback in two places. Both of these places do not
hold r_lock. Fix this by acquiring a spin_lock of r_lock in both of
these places.
The r_lock acquiring cannot be added in rvt_qp_complete_swqe because
some of its other callers already have r_lock acquired.
The existing logic happens to work fine on UML, but is not correct when
running on other arches.
1. We didn't initialize `int err`, and kunit_filter_suites() doesn't
explicitly set it to 0 on success. So we had false "failures".
Note: it doesn't happen on UML, causing this to get overlooked.
2. If we error out, we do not call kunit_handle_shutdown().
This makes kunit.py timeout when using a non-UML arch, since the QEMU
process doesn't ever exit.
Fixes: a02353f49162 ("kunit: bail out of test filtering logic quicker if OOM") Signed-off-by: Daniel Latypov <dlatypov@google.com> Reviewed-by: Brendan Higgins <brendanhiggins@google.com> Signed-off-by: Shuah Khan <skhan@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In tcmu_blocks_release(), lock_page() is called to prevent a race causing
possible data corruption. Since lock_page() might sleep, calling it while
holding XArray lock is a bug.
To fix this, replace the xas_for_each() call with xa_for_each_range().
Since the latter does its own handling of XArray locking, the xas_lock()
and xas_unlock() calls around the original loop are no longer necessary.
The switch to xa_for_each_range() slows down the loop slightly. This is
acceptable since tcmu_blocks_release() is not relevant for performance.
Link: https://lore.kernel.org/r/20220517192913.21405-1-bostroesser@gmail.com Fixes: bb9b9eb0ae2e ("scsi: target: tcmu: Fix possible data corruption") Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Bodo Stroesser <bostroesser@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit c724c866bb70 ("linux/types.h: remove unnecessary __bitwise__")
was right that there are no users of __bitwise__ in the kernel, but it
turns out there are user space users of it that do expect it.
It is, after all, in the uapi directory, so user space usage is to be
expected.
Instead of reverting the commit completely, let's just clarify the
situation so that it doesn't happen again, and have some in-code
explanations for why that "__bitwise__" still exists.
Before this patch, functions gfs2_qa_get and _put used the i_rw_mutex to
prevent simultaneous access to its i_qadata. But i_rw_mutex is now used
for many other things, including iomap_begin and end, which causes a
conflict according to lockdep. We cannot just remove the lock since
simultaneous opens (gfs2_open -> gfs2_open_common -> gfs2_qa_get) can
then stomp on each others values for i_qadata.
This patch solves the conflict by using the i_lock spin_lock in the inode
to prevent simultaneous access.
Signed-off-by: Bob Peterson <rpeterso@redhat.com> Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Latest llvm-project upstream had a change of behavior
related to qualifiers on function return type ([1]).
This caused selftests btf_dump/btf_dump failure.
The following example shows what changed.
$ cat t.c
typedef const char * const (* const (* const fn_ptr_arr2_t[5])())(char * (*)(int));
struct t {
int a;
fn_ptr_arr2_t l;
};
int foo(struct t *arg) {
return arg->a;
}
To adapt the selftest to both old and new llvm, this patch removed
the intermediate const qualifier in const-to-ptr types, to make the
test succeed again.
Returning an error value in an i2c remove callback results in an error
message being emitted by the i2c core, but otherwise it doesn't make a
difference. The device goes away anyhow and the devm cleanups are
called.
As tpm_cr50_i2c_remove() emits an error message already and the
additional error message by the i2c core doesn't add any useful
information, change the return value to zero to suppress this error
message.
Note that if i2c_clientdata is NULL, there is something really fishy.
Assuming no memory corruption happened (then all bets are lost anyhow),
tpm_cr50_i2c_remove() is only called after tpm_cr50_i2c_probe() returned
successfully. So there was a tpm chip registered before and after
tpm_cr50_i2c_remove() its privdata is freed but the associated character
device isn't removed. If after that happened userspace accesses the
character device it's likely that the freed memory is accessed. For that
reason the warning message is made a bit more frightening.
i is guaranteed < tp->irq_max which in turn is either 1 or 5.
There are more loops like this one in the driver, but strangely
GCC 12 dislikes only this single one.
Silence this silliness for now.
Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
If a client's address changes, say if it is NAT'd, this can disrupt an in
progress operation. For most operations, this is not much of a problem,
but StoreData can be different as some servers modify the target file as
the data comes in, so if a store request is disrupted, the file can get
corrupted on the server.
The problem is that the server doesn't recognise packets that come after
the change of address as belonging to the original client and will bounce
them, either by sending an OUT_OF_SEQUENCE ACK to the apparent new call if
the packet number falls within the initial sequence number window of a call
or by sending an EXCEEDS_WINDOW ACK if it falls outside and then aborting
it. In both cases, firstPacket will be 1 and previousPacket will be 0 in
the ACK information.
Fix this by the following means:
(1) If a client call receives an EXCEEDS_WINDOW ACK with firstPacket as 1
and previousPacket as 0, assume this indicates that the server saw the
incoming packets from a different peer and thus as a different call.
Fail the call with error -ENETRESET.
(2) Also fail the call if a similar OUT_OF_SEQUENCE ACK occurs if the
first packet has been hard-ACK'd. If it hasn't been hard-ACK'd, the
ACK packet will cause it to get retransmitted, so the call will just
be repeated.
(3) Make afs_select_fileserver() treat -ENETRESET as a straight fail of
the operation.
(4) Prioritise the error code over things like -ECONNRESET as the server
did actually respond.
(5) Make writeback treat -ENETRESET as a retryable error and make it
redirty all the pages involved in a write so that the VM will retry.
Note that there is still a circumstance that I can't easily deal with: if
the operation is fully received and processed by the server, but the reply
is lost due to address change. There's no way to know if the op happened.
We can examine the server, but a conflicting change could have been made by
a third party - and we can't tell the difference. In such a case, a
message like:
will be logged to dmesg on the next op to touch the file and the client
will reset the inode state, including invalidating clean parts of the
pagecache.
Reported-by: Marc Dionne <marc.dionne@auristor.com> Signed-off-by: David Howells <dhowells@redhat.com>
cc: linux-afs@lists.infradead.org Link: http://lists.infradead.org/pipermail/linux-afs/2021-December/004811.html Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The RX_USER_ABORT code should really only be used to indicate that the user
of the rxrpc service (ie. userspace) implicitly caused a call to be aborted
- for instance if the AF_RXRPC socket is closed whilst the call was in
progress. (The user may also explicitly abort a call and specify the abort
code to use).
Change some of the points of generation to use other abort codes instead:
(1) Abort the call with RXGEN_SS_UNMARSHAL or RXGEN_CC_UNMARSHAL if we see
ENOMEM and EFAULT during received data delivery and abort with
RX_CALL_DEAD in the default case.
(2) Abort with RXGEN_SS_MARSHAL if we get ENOMEM whilst trying to send a
reply.
(3) Abort with RX_CALL_DEAD if we stop hearing from the peer if we had
heard from the peer and abort with RX_CALL_TIMEOUT if we hadn't.
(4) Abort with RX_CALL_DEAD if we try to disconnect a call that's not
completed successfully or been aborted.
Reported-by: Jeffrey Altman <jaltman@auristor.com> Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
If at the end of rxrpc sendmsg() or rxrpc_kernel_send_data() the call that
was being given data was aborted remotely or otherwise failed, return an
error rather than returning the amount of data buffered for transmission.
The call (presumably) did not complete, so there's not much point
continuing with it. AF_RXRPC considers it "complete" and so will be
unwilling to do anything else with it - and won't send a notification for
it, deeming the return from sendmsg sufficient.
Not returning an error causes afs to incorrectly handle a StoreData
operation that gets interrupted by a change of address due to NAT
reconfiguration.
This doesn't normally affect most operations since their request parameters
tend to fit into a single UDP packet and afs_make_call() returns before the
server responds; StoreData is different as it involves transmission of a
lot of data.
This can be triggered on a client by doing something like:
The Auristor fileserver logs code -453 (RXGEN_SS_UNMARSHAL), but the abort
code received by kafs is -5 (RX_PROTOCOL_ERROR) as the rx layer sees the
condition and generates an abort first and the unmarshal error is a
consequence of that at the application layer.
Reported-by: Marc Dionne <marc.dionne@auristor.com> Signed-off-by: David Howells <dhowells@redhat.com>
cc: linux-afs@lists.infradead.org Link: http://lists.infradead.org/pipermail/linux-afs/2021-December/004810.html Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The macros implementing Atari ROM port I/O writes do not cast away their
output, unlike similar implementations for other I/O buses.
When they are combined using conditional expressions in the definitions of
outb() and friends, this triggers sparse warnings like:
drivers/net/appletalk/cops.c:382:17: error: incompatible types in conditional expression (different base types):
drivers/net/appletalk/cops.c:382:17: unsigned char
drivers/net/appletalk/cops.c:382:17: void
Currently the trampoline_count test doesn't include any fmod_ret bpf
programs, fix it to make the test cover all possible trampoline program
types.
Since fmod_ret bpf programs can't be attached to __set_task_comm function,
as it's neither whitelisted for error injection nor a security hook, change
it to bpf_modify_return_test.
This patch also does some other cleanups such as removing duplicate code,
dropping inconsistent comments, etc.
If we program an RX endpoint to have no header (header length is 0),
header-related endpoint configuration values are meaningless and are
ignored.
The only case we support that defines a header is QMAP endpoints.
In ipa_endpoint_init_hdr_ext() we set the endianness mask value
unconditionally, but it should not be done if there is no header
(meaning it is not configured for QMAP).
Set the endianness conditionally, and rearrange the logic in that
function slightly to avoid testing the qmap flag twice.
Delete an incorrect comment in ipa_endpoint_init_aggr().
Signed-off-by: Alex Elder <elder@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Starting from LLVM 14, having an unpacked struct nested in a packed
struct triggers a warning. c.f. [1].
This is a false positive because the field is always being accessed
with the relevant put_unaligned_*() function. Adding __packed to the
structure declaration silences the warning.
In current implementation we set the non-mdts limits by calling
nvme_init_non_mdts_limits() from nvme_init_ctrl_finish().
This also tries to set the limits for the discovery controller which
has no I/O queues resulting in the warning message reported by the
nvme_log_error() when running blktest nvme/002: -
[ 2005.155946] run blktests nvme/002 at 2022-04-09 16:57:47
[ 2005.192223] loop: module loaded
[ 2005.196429] nvmet: adding nsid 1 to subsystem blktests-subsystem-0
[ 2005.200334] nvmet: adding nsid 1 to subsystem blktests-subsystem-1
[ 2008.958108] nvmet: adding nsid 1 to subsystem blktests-subsystem-997
[ 2008.962082] nvmet: adding nsid 1 to subsystem blktests-subsystem-998
[ 2008.966102] nvmet: adding nsid 1 to subsystem blktests-subsystem-999
[ 2008.973132] nvmet: creating discovery controller 1 for subsystem nqn.2014-08.org.nvmexpress.discovery for NQN testhostnqn.
*[ 2008.973196] nvme1: Identify(0x6), Invalid Field in Command (sct 0x0 / sc 0x2) MORE DNR*
[ 2008.974595] nvme nvme1: new ctrl: "nqn.2014-08.org.nvmexpress.discovery"
[ 2009.103248] nvme nvme1: Removing ctrl: NQN "nqn.2014-08.org.nvmexpress.discovery"
Move the call of nvme_init_non_mdts_limits() to nvme_scan_work() after
we verify that I/O queues are created since that is a converging point
for each transport where these limits are actually used.
1. FC :
nvme_fc_create_association()
...
nvme_fc_create_io_queues(ctrl);
...
nvme_start_ctrl()
nvme_scan_queue()
nvme_scan_work()
The transition_delay_us (struct cpufreq_policy) is currently defined
as:
Preferred average time interval between consecutive invocations of
the driver to set the frequency for this policy. To be set by the
scaling driver (0, which is the default, means no preference).
The transition_latency represents the amount of time necessary for a
CPU to change its frequency.
A PCCT table advertises mutliple values:
- pcc_nominal: Expected latency to process a command, in microseconds
- pcc_mpar: The maximum number of periodic requests that the subspace
channel can support, reported in commands per minute. 0 indicates no
limitation.
- pcc_mrtt: The minimum amount of time that OSPM must wait after the
completion of a command before issuing the next command,
in microseconds.
cppc_get_transition_latency() allows to get the max of them.
commit d4f3388afd48 ("cpufreq / CPPC: Set platform specific
transition_delay_us") allows to select transition_delay_us based on
the platform, and fallbacks to cppc_get_transition_latency()
otherwise.
If _CPC objects are not using PCC channels (no PPCT table), the
transition_delay_us is set to CPUFREQ_ETERNAL, leading to really long
periods between frequency updates (~4s).
If the desired_reg, where performance requests are written, is in
SystemMemory or SystemIo ACPI address space, there is no delay
in requests. So return 0 instead of CPUFREQ_ETERNAL, leading to
transition_delay_us being set to LATENCY_MULTIPLIER us (1000 us).
This patch also adds two macros to check the address spaces.
Signed-off-by: Pierre Gondois <pierre.gondois@arm.com> Reviewed-by: Sudeep Holla <sudeep.holla@arm.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
1.In current process, all bio will set the BIO_THROTTLED flag
after __blk_throtl_bio().
2.If bio needs to be throttled, it will start the timer and
stop submit bio directly. Bio will submit in
blk_throtl_dispatch_work_fn() when the timer expires.But in
the current process, if bio is throttled. The BIO_THROTTLED
will be set to bio after timer start. If the bio has been
completed, it may cause use-after-free blow.
BUG: KASAN: use-after-free in blk_throtl_bio+0x12f0/0x2c70
Read of size 2 at addr ffff88801b8902d4 by task fio/26380
When we boot a machine using a devicetree, the generic DT code goes
through all nodes with a 'device_type = "memory"' property, and collects
all memory banks mentioned there. However it does not check for the
status property, so any nodes which are explicitly "disabled" will still
be added as a memblock.
This ends up badly for QEMU, when booting with secure firmware on
arm/arm64 machines, because QEMU adds a node describing secure-only
memory:
===================
secram@e000000 {
secure-status = "okay";
status = "disabled";
reg = <0x00 0xe000000 0x00 0x1000000>;
device_type = "memory";
};
===================
The kernel will eventually use that memory block (which is located below
the main DRAM bank), but accesses to that will be answered with an
SError:
===================
[ 0.000000] Internal error: synchronous external abort: 96000050 [#1] PREEMPT SMP
[ 0.000000] Modules linked in:
[ 0.000000] CPU: 0 PID: 0 Comm: swapper Not tainted 5.18.0-rc6-00014-g10c8acb8b679 #524
[ 0.000000] Hardware name: linux,dummy-virt (DT)
[ 0.000000] pstate: 200000c5 (nzCv daIF -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
[ 0.000000] pc : new_slab+0x190/0x340
[ 0.000000] lr : new_slab+0x184/0x340
[ 0.000000] sp : ffff80000a4b3d10
....
==================
The actual crash location and call stack will be somewhat random, and
depend on the specific allocation of that physical memory range.
As the DT spec[1] explicitly mentions standard properties, add a simple
check to skip over disabled memory nodes, so that we only use memory
that is meant for non-secure code to use.
That fixes booting a QEMU arm64 VM with EL3 enabled ("secure=on"), when
not using UEFI. In this case the QEMU generated DT will be handed on
to the kernel, which will see the secram node.
This issue is reproducible when using TF-A together with U-Boot as
firmware, then booting with the "booti" command.
When using U-Boot as an UEFI provider, the code there [2] explicitly
filters for disabled nodes when generating the UEFI memory map, so we
are safe.
EDK/2 only reads the first bank of the first DT memory node [3] to learn
about memory, so we got lucky there.
[1] https://github.com/devicetree-org/devicetree-specification/blob/main/source/chapter3-devicenodes.rst#memory-node (after the table)
[2] https://source.denx.de/u-boot/u-boot/-/blob/master/lib/fdtdec.c#L1061-1063
[3] https://github.com/tianocore/edk2/blob/master/ArmVirtPkg/PrePi/FdtParser.c
The hardware expects FrameNumWrap or long_term_frame_idx. Picture
numbers are per field, and are mostly used during the memory
management process, which is done in userland. This fixes two
ITU conformance tests:
- MR6_BT_B
- MR8_BT_B
Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com> Reviewed-by: Sebastian Fricke <sebastian.fricke@collabora.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Consider this invocation
$ ./tools/testing/kunit/kunit.py parse <<EOF
TAP version 14
1..2
ok 1 - suite
# Subtest: no_tests_suite
# catastrophic error!
not ok 1 - no_tests_suite
EOF
It will have a 0 exit code even though there's a "not ok".
Consider this one:
$ ./tools/testing/kunit/kunit.py parse <<EOF
TAP version 14
1..2
ok 1 - suite
not ok 1 - no_tests_suite
EOF
It will a non-zero exit code.
Why?
We have this line in the kunit_parser.py
> parent_test = parse_test_header(lines, test)
where we have special handling when we see "# Subtest" and we ignore the
explicit reported "not ok 1" status!
Also, NO_TESTS at a suite-level only results in a non-zero status code
where then there's only one suite atm.
This change is the minimal one to make sure we don't overwrite it.
Signed-off-by: Daniel Latypov <dlatypov@google.com> Reviewed-by: David Gow <davidgow@google.com> Reviewed-by: Brendan Higgins <brendanhiggins@google.com> Signed-off-by: Shuah Khan <skhan@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When btrfs_qgroup_inherit(), btrfs_alloc_tree_block, or
btrfs_insert_root() fail in create_subvol(), we return without freeing
anon_dev. Reorganize the error handling in create_subvol() to fix this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
smartshift apu and dgpu power boost are reported as percentage
with respect to their power limits. adjust the units of power before
calculating the percentage of boost.
Signed-off-by: Sathishkumar S <sathishkumar.sundararaju@amd.com> Reviewed-by: Lijo Lazar <lijo.lazar@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / thirdparty / kernel / stable.git / log
