Several net tests requires an XDP program build under the ebpf
directory, and error out if such program is not available.
That makes running successful net test hard, let's duplicate into the
net dir the [very small] program, re-using the existing rules to build
it, and finally dropping the bogus dependency.
'struct hidraw_list' is a circular queue whose head can be smaller than
tail. Using 'list->tail != list->head' to release all memory that should
be released.
Fixes: a5623a203cff ("HID: hidraw: fix memory leak in hidraw_release()") Signed-off-by: Su Hui <suhui@nfschina.com> Reviewed-by: Dan Carpenter <dan.carpenter@linaro.org> Signed-off-by: Jiri Kosina <jkosina@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Inside scsi_eh_wakeup(), scsi_host_busy() is called & checked with host
lock every time for deciding if error handler kthread needs to be waken up.
This can be too heavy in case of recovery, such as:
- N hardware queues
- queue depth is M for each hardware queue
- each scsi_host_busy() iterates over (N * M) tag/requests
If recovery is triggered in case that all requests are in-flight, each
scsi_eh_wakeup() is strictly serialized, when scsi_eh_wakeup() is called
for the last in-flight request, scsi_host_busy() has been run for (N * M -
1) times, and request has been iterated for (N*M - 1) * (N * M) times.
If both N and M are big enough, hard lockup can be triggered on acquiring
host lock, and it is observed on mpi3mr(128 hw queues, queue depth 8169).
Fix the issue by calling scsi_host_busy() outside the host lock. We don't
need the host lock for getting busy count because host the lock never
covers that.
[mkp: Drop unnecessary 'busy' variables pointed out by Bart]
Cc: Ewan Milne <emilne@redhat.com> Fixes: 6eb045e092ef ("scsi: core: avoid host-wide host_busy counter for scsi_mq") Signed-off-by: Ming Lei <ming.lei@redhat.com> Link: https://lore.kernel.org/r/20240112070000.4161982-1-ming.lei@redhat.com Reviewed-by: Ewan D. Milne <emilne@redhat.com> Reviewed-by: Sathya Prakash Veerichetty <safhya.prakash@broadcom.com> Tested-by: Sathya Prakash Veerichetty <safhya.prakash@broadcom.com> Reviewed-by: Bart Van Assche <bvanassche@acm.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
We can't use devm_platform_ioremap_resource_byname() to remap the
interrupt register that can be shared between
regulator-abb-{ivahd,dspeve,gpu} drivers instances.
The combined helper introduce a call to devm_request_mem_region() that
creates a new busy resource region on PRM_IRQSTATUS_MPU register
(0x4ae06010). The first devm_request_mem_region() call succeeds for
regulator-abb-ivahd but fails for the two other regulator-abb-dspeve
and regulator-abb-gpu.
regulator-abb-dspeve and regulator-abb-gpu are missing due to
devm_request_mem_region() failure (EBUSY):
[ 1.326660] ti_abb 4ae07e30.regulator-abb-dspeve: can't request region for resource [mem 0x4ae06010-0x4ae06013]
[ 1.326660] ti_abb: probe of 4ae07e30.regulator-abb-dspeve failed with error -16
[ 1.327239] ti_abb 4ae07de4.regulator-abb-gpu: can't request region for resource [mem 0x4ae06010-0x4ae06013]
[ 1.327270] ti_abb: probe of 4ae07de4.regulator-abb-gpu failed with error -16
>From arm/boot/dts/dra7.dtsi:
The abb_mpu is the only instance using its own interrupt register:
(0x4ae06014) PRM_IRQSTATUS_MPU_2, ABB_MPU_DONE_ST (bit 7)
The other tree instances (abb_ivahd, abb_dspeve, abb_gpu) share
PRM_IRQSTATUS_MPU register (0x4ae06010) but use different bits
ABB_IVA_DONE_ST (bit 30), ABB_DSPEVE_DONE_ST( bit 29) and
ABB_GPU_DONE_ST (but 28).
The commit b36c6b1887ff ("regulator: ti-abb: Make use of the helper
function devm_ioremap related") overlooked the following comment
implicitly explaining why devm_ioremap() is used in this case:
/*
* We may have shared interrupt register offsets which are
* write-1-to-clear between domains ensuring exclusivity.
*/
Fixes and partially reverts commit b36c6b1887ff ("regulator: ti-abb:
Make use of the helper function devm_ioremap related").
Improve the existing comment to avoid further conversion to
devm_platform_ioremap_resource_byname().
Fixes: b36c6b1887ff ("regulator: ti-abb: Make use of the helper function devm_ioremap related") Signed-off-by: Romain Naour <romain.naour@skf.com> Reviewed-by: Yoann Congal <yoann.congal@smile.fr> Link: https://msgid.link/r/20240123111456.739381-1-romain.naour@smile.fr Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit 2810c1e99867 ("kunit: Fix wild-memory-access bug in
kunit_free_suite_set()") fixed a wild-memory-access bug that could have
happened during the loading phase of test suites built and executed as
loadable modules. However, it also introduced a problematic side effect
that causes test suites modules to crash when they attempt to register
fake devices.
When a module is loaded, it traverses the MODULE_STATE_UNFORMED and
MODULE_STATE_COMING states before reaching the normal operating state
MODULE_STATE_LIVE. Finally, when the module is removed, it moves to
MODULE_STATE_GOING before being released. However, if the loading
function load_module() fails between complete_formation() and
do_init_module(), the module goes directly from MODULE_STATE_COMING to
MODULE_STATE_GOING without passing through MODULE_STATE_LIVE.
This behavior was causing kunit_module_exit() to be called without
having first executed kunit_module_init(). Since kunit_module_exit() is
responsible for freeing the memory allocated by kunit_module_init()
through kunit_filter_suites(), this behavior was resulting in a
wild-memory-access bug.
Commit 2810c1e99867 ("kunit: Fix wild-memory-access bug in
kunit_free_suite_set()") fixed this issue by running the tests when the
module is still in MODULE_STATE_COMING. However, modules in that state
are not fully initialized, lacking sysfs kobjects. Therefore, if a test
module attempts to register a fake device, it will inevitably crash.
This patch proposes a different approach to fix the original
wild-memory-access bug while restoring the normal module execution flow
by making kunit_module_exit() able to detect if kunit_module_init() has
previously initialized the tests suite set. In this way, test modules
can once again register fake devices without crashing.
This behavior is achieved by checking whether mod->kunit_suites is a
virtual or direct mapping address. If it is a virtual address, then
kunit_module_init() has allocated the suite_set in kunit_filter_suites()
using kmalloc_array(). On the contrary, if mod->kunit_suites is still
pointing to the original address that was set when looking up the
.kunit_test_suites section of the module, then the loading phase has
failed and there's no memory to be freed.
v4:
- rebased on 6.8
- noted that kunit_filter_suites() must return a virtual address
v3:
- add a comment to clarify why the start address is checked
v2:
- add include <linux/mm.h>
Fixes: 2810c1e99867 ("kunit: Fix wild-memory-access bug in kunit_free_suite_set()") Reviewed-by: David Gow <davidgow@google.com> Tested-by: Rae Moar <rmoar@google.com> Tested-by: Richard Fitzgerald <rf@opensource.cirrus.com> Reviewed-by: Javier Martinez Canillas <javierm@redhat.com> Signed-off-by: Marco Pagani <marpagan@redhat.com> Signed-off-by: Shuah Khan <skhan@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 66f1e6809397 ("riscv: Make XIP bootable again") restricted page
offset to the sv39 page offset instead of the default sv57, which makes
sense since probably the platforms that target XIP kernels do not
support anything else than sv39 and we do not try to find out the
largest address space supported on XIP kernels (ie set_satp_mode()).
But PAGE_OFFSET_L3 is not defined for rv32, so fix the build error by
restoring the previous behaviour which picks CONFIG_PAGE_OFFSET for rv32.
Fixes: 66f1e6809397 ("riscv: Make XIP bootable again") Reported-by: Randy Dunlap <rdunlap@infradead.org> Closes: https://lore.kernel.org/linux-riscv/344dca85-5c48-44e1-bc64-4fa7973edd12@infradead.org/T/#u Signed-off-by: Alexandre Ghiti <alexghiti@rivosinc.com> Acked-by: Randy Dunlap <rdunlap@infradead.org> Tested-by: Randy Dunlap <rdunlap@infradead.org> # build-tested Link: https://lore.kernel.org/r/20240118212120.2087803-1-alexghiti@rivosinc.com Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fix up on mes process context flush to prevent non-mes devices from
spamming error messages or running into undefined behaviour during
process termination.
Fixes: bd33bb1409b4 ("drm/amdkfd: fix mes set shader debugger process management") Signed-off-by: Jonathan Kim <jonathan.kim@amd.com> Reviewed-by: Eric Huang <jinhuieric.huang@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Some pending include file cleanups produced this error:
In file included from include/linux/kernel.h:27,
from drivers/gpu/ipu-v3/ipu-dp.c:7:
include/drm/drm_color_mgmt.h: In function 'drm_color_lut_extract':
include/drm/drm_color_mgmt.h:45:46: error: implicit declaration of function 'mul_u32_u32' [-Werror=implicit-function-declaration]
45 | return DIV_ROUND_CLOSEST_ULL(mul_u32_u32(user_input, (1 << bit_precision) - 1),
| ^~~~~~~~~~~
Replace rcu_dereference() with rcu_access_pointer() since we hold
the lock here (and aren't in an RCU critical section).
Fixes: 32af9a9e1069 ("wifi: cfg80211: free beacon_ies when overridden from hidden BSS") Reported-and-tested-by: syzbot+864a269c27ee06b58374@syzkaller.appspotmail.com Signed-off-by: Edward Adam Davis <eadavis@qq.com> Link: https://msgid.link/tencent_BF8F0DF0258C8DBF124CDDE4DD8D992DCF07@qq.com Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Thomas reported that commit 652ffc2104ec ("perf/core: Fix narrow
startup race when creating the perf nr_addr_filters sysfs file") made
the entire attribute group vanish, instead of only the nr_addr_filters
attribute.
Additionally a stray return.
Insufficient coffee was involved with both writing and merging the
patch.
Fixes: 652ffc2104ec ("perf/core: Fix narrow startup race when creating the perf nr_addr_filters sysfs file") Reported-by: Thomas Richter <tmricht@linux.ibm.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Tested-by: Thomas Richter <tmricht@linux.ibm.com> Link: https://lkml.kernel.org/r/20231122100756.GP8262@noisy.programming.kicks-ass.net Signed-off-by: Sasha Levin <sashal@kernel.org>
Range interval [start, last] is ordered by rb_tree, rb_prev, rb_next
return value still needs NULL check, thus modified from "node" to "rb_node".
Fixes the below:
drivers/gpu/drm/amd/amdgpu/../amdkfd/kfd_svm.c:2691 svm_range_get_range_boundaries() warn: can 'node' even be NULL?
Suggested-by: Philip Yang <Philip.Yang@amd.com> Cc: Felix Kuehling <Felix.Kuehling@amd.com> Cc: Christian König <christian.koenig@amd.com> Cc: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com> Reviewed-by: Felix Kuehling <felix.kuehling@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In function 'amdgpu_device_need_post(struct amdgpu_device *adev)' -
'adev->pm.fw' may not be released before return.
Using the function release_firmware() to release adev->pm.fw.
Thus fixing the below:
drivers/gpu/drm/amd/amdgpu/amdgpu_device.c:1571 amdgpu_device_need_post() warn: 'adev->pm.fw' from request_firmware() not released on lines: 1554.
Cc: Monk Liu <Monk.Liu@amd.com> Cc: Christian König <christian.koenig@amd.com> Cc: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com> Suggested-by: Lijo Lazar <lijo.lazar@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The amdgpu_gmc_vram_checking() function in emulation checks whether
all of the memory range of shared system memory could be accessed by
GPU, from this aspect, -EIO is returned for error scenarios.
Cc: Xiaojian Du <Xiaojian.Du@amd.com> Cc: Lijo Lazar <lijo.lazar@amd.com> Cc: Christian König <christian.koenig@amd.com> Cc: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com> Suggested-by: Christian König <christian.koenig@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In 'struct phm_ppm_table *ptr' allocation using kzalloc, an incorrect
structure type is passed to sizeof() in kzalloc, larger structure types
were used, thus using correct type 'struct phm_ppm_table' fixes the
below:
drivers/gpu/drm/amd/amdgpu/../pm/powerplay/hwmgr/process_pptables_v1_0.c:203 get_platform_power_management_table() warn: struct type mismatch 'phm_ppm_table vs _ATOM_Tonga_PPM_Table'
Cc: Eric Huang <JinHuiEric.Huang@amd.com> Cc: Christian König <christian.koenig@amd.com> Cc: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com> Acked-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
This issue is reported by smatch that get_quota_realm() might return
ERR_PTR but we did not handle it. It's not a immediate bug, while we
still should address it to avoid potential bugs if get_quota_realm()
is changed to return other ERR_PTR in future.
Set ceph_snap_realm's pointer in get_quota_realm()'s to address this
issue, the pointer would be set to NULL if get_quota_realm() failed
to get struct ceph_snap_realm, so no ERR_PTR would happen any more.
Following along the same lines as per the user-space fix. Right
now this isn't really an issue with the ceph kernel driver because
of the feature bit laginess, however, that can change over time
(when the new snaprealm info type is ported to the kernel driver)
and depending on the MDS version that's being upgraded can cause
message decoding issues - so, fix that early on.
In blk_mq_mark_tag_wait(), __add_wait_queue() may be re-ordered
with the following blk_mq_get_driver_tag() in case of getting driver
tag failure.
Then in __sbitmap_queue_wake_up(), waitqueue_active() may not observe
the added waiter in blk_mq_mark_tag_wait() and wake up nothing, meantime
blk_mq_mark_tag_wait() can't get driver tag successfully.
This issue can be reproduced by running the following test in loop, and
fio hang can be observed in < 30min when running it on my test VM
in laptop.
"
drivers/net/virtio_net.c: In function ‘init_vqs’:
drivers/net/virtio_net.c:4551:48: warning: ‘%d’ directive writing between 1 and 11 bytes into a region of size 10 [-Wformat-overflow=]
4551 | sprintf(vi->rq[i].name, "input.%d", i);
| ^~
In function ‘virtnet_find_vqs’,
inlined from ‘init_vqs’ at drivers/net/virtio_net.c:4645:8:
drivers/net/virtio_net.c:4551:41: note: directive argument in the range [-2147483643, 65534]
4551 | sprintf(vi->rq[i].name, "input.%d", i);
| ^~~~~~~~~~
drivers/net/virtio_net.c:4551:17: note: ‘sprintf’ output between 8 and 18 bytes into a destination of size 16
4551 | sprintf(vi->rq[i].name, "input.%d", i);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/virtio_net.c: In function ‘init_vqs’:
drivers/net/virtio_net.c:4552:49: warning: ‘%d’ directive writing between 1 and 11 bytes into a region of size 9 [-Wformat-overflow=]
4552 | sprintf(vi->sq[i].name, "output.%d", i);
| ^~
In function ‘virtnet_find_vqs’,
inlined from ‘init_vqs’ at drivers/net/virtio_net.c:4645:8:
drivers/net/virtio_net.c:4552:41: note: directive argument in the range [-2147483643, 65534]
4552 | sprintf(vi->sq[i].name, "output.%d", i);
| ^~~~~~~~~~~
drivers/net/virtio_net.c:4552:17: note: ‘sprintf’ output between 9 and 19 bytes into a destination of size 16
4552 | sprintf(vi->sq[i].name, "output.%d", i);
Signed-off-by: Philip Yang <Philip.Yang@amd.com> Reviewed-by: Felix Kuehling <felix.kuehling@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
I believe this cannot really lead to a deadlock in practice, because
svm_range_evict_svm_bo_worker only takes the mmap_read_lock if the BO
refcount is non-0. That means it's impossible that svm_range_bo_release
is running concurrently. However, there is no good way to annotate this.
To avoid the problem, take a BO reference in
svm_range_schedule_evict_svm_bo instead of in the worker. That way it's
impossible for a BO to get freed while eviction work is pending and the
cancel_work_sync call in svm_range_bo_release can be eliminated.
v2: Use svm_bo_ref_unless_zero and explained why that's safe. Also
removed redundant checks that are already done in
amdkfd_fence_enable_signaling.
Signed-off-by: Felix Kuehling <felix.kuehling@amd.com> Reviewed-by: Philip Yang <philip.yang@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
uniq() will write one command name over another causing the overwritten
string to be leaked. Fix by doing a pass that removes duplicates and a
second that removes the holes.
Signed-off-by: Ian Rogers <irogers@google.com> Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Chenyuan Mi <cymi20@fudan.edu.cn> Cc: Ingo Molnar <mingo@redhat.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Link: https://lore.kernel.org/r/20231208000515.1693746-1-irogers@google.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The lis3lv02d_i2c driver was missing a line to set the lis3_dev's
reg_ctrl callback.
lis3_reg_ctrl(on) is called from the init callback, but due to
the missing reg_ctrl callback the regulators where never turned off
again leading to the following oops/backtrace when detaching the driver:
The xhci retaining bogus hardware states cause usb disconnect devices
connected before hibernation(s4) and refer to the commit 'f3d478858be
("usb: ohci-platform: fix usb disconnect issue after s4")' which set
flag "hibernated" as true when resume-from-hibernation and that the
drivers will reset the hardware to get rid of any existing state and
make sure resume from hibernation re-enumerates everything for xhci.
The 9p filesystem is calling netfs_inode_init() in v9fs_init_inode() -
before the struct inode fields have been initialised from the obtained file
stats (ie. after v9fs_stat2inode*() has been called), but netfslib wants to
set a couple of its fields from i_size.
Reported-by: Marc Dionne <marc.dionne@auristor.com> Signed-off-by: David Howells <dhowells@redhat.com> Tested-by: Marc Dionne <marc.dionne@auristor.com> Tested-by: Dominique Martinet <asmadeus@codewreck.org> Acked-by: Dominique Martinet <asmadeus@codewreck.org>
cc: Eric Van Hensbergen <ericvh@kernel.org>
cc: Latchesar Ionkov <lucho@ionkov.net>
cc: Dominique Martinet <asmadeus@codewreck.org>
cc: Christian Schoenebeck <linux_oss@crudebyte.com>
cc: v9fs@lists.linux.dev
cc: linux-cachefs@redhat.com
cc: linux-fsdevel@vger.kernel.org Signed-off-by: Sasha Levin <sashal@kernel.org>
When a device with AER detects an error, it logs error information in its
own AER Error Status registers. It may send an Error Message to the Root
Port (RCEC in the case of an RCiEP), which logs the fact that an Error
Message was received (Root Error Status) and the Requester ID of the
message source (Error Source Identification).
aer_print_port_info() prints the Requester ID from the Root Port Error
Source in the usual Linux "bb:dd.f" format, but when find_source_device()
finds no error details in the hierarchy below the Root Port, it printed the
raw Requester ID without decoding it.
Decode the Requester ID in the usual Linux format so it matches other
messages.
Sample message changes:
- pcieport 0000:00:1c.5: AER: Correctable error received: 0000:00:1c.5
- pcieport 0000:00:1c.5: AER: can't find device of ID00e5
+ pcieport 0000:00:1c.5: AER: Correctable error message received from 0000:00:1c.5
+ pcieport 0000:00:1c.5: AER: found no error details for 0000:00:1c.5
Unlike the lower rates, the PCIe 64GT/s Data Rate uses 1b/1b encoding, not
128b/130b (PCIe r6.1 sec 1.2, Table 1-1). Correct the PCIE_SPEED2MBS_ENC()
calculation to reflect that.
The pmif driver data that contains the clocks is allocated along with
spmi_controller.
On device remove, spmi_controller will be freed first, and then devres
, including the clocks, will be cleanup.
This leads to UAF because putting the clocks will access the clocks in
the pmif driver data, which is already freed along with spmi_controller.
This can be reproduced by enabling DEBUG_TEST_DRIVER_REMOVE and
building the kernel with KASAN.
Fix the UAF issue by using unmanaged clk_bulk_get() and putting the
clocks before freeing spmi_controller.
Handling of S_ISGID is usually done by inode_init_owner() in all other
filesystems, but kernfs doesn't use that function. In kernfs, struct
kernfs_node is the primary data structure, and struct inode is only
created from it on demand. Therefore, inode_init_owner() can't be
used and we need to imitate its behavior.
S_ISGID support is useful for the cgroup filesystem; it allows
subtrees managed by an unprivileged process to retain a certain owner
gid, which then enables sharing access to the subtree with another
unprivileged process.
The capability CAP_CHECKPOINT_RESTORE was introduced to allow non-root
users to checkpoint and restore processes as non-root with CRIU.
This change extends CAP_CHECKPOINT_RESTORE to enable the CRIU option
'--shell-job' as non-root. CRIU's man-page describes the '--shell-job'
option like this:
Allow one to dump shell jobs. This implies the restored task will
inherit session and process group ID from the criu itself. This option
also allows to migrate a single external tty connection, to migrate
applications like top.
TIOCSLCKTRMIOS can only be done if the process has CAP_SYS_ADMIN and
this change extends it to CAP_SYS_ADMIN or CAP_CHECKPOINT_RESTORE.
With this change it is possible to checkpoint and restore processes
which have a tty connection as non-root if CAP_CHECKPOINT_RESTORE is
set.
Acked-by: Christian Brauner <brauner@kernel.org> Signed-off-by: Adrian Reber <areber@redhat.com> Acked-by: Andrei Vagin <avagin@gmail.com> Link: https://lore.kernel.org/r/20231208143656.1019-1-areber@redhat.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
DEFINED only considers symbols, not section names. Hence, replace the
check for .got.plt with the _GLOBAL_OFFSET_TABLE_ symbol and remove other
(non-essential) asserts.
There is a potential delay in notifying Linux USB drivers of downstream
USB bus activity when connecting a high-speed or superSpeed device via the
Microchip USB491x hub. This delay is due to the fixed bInterval value of
12 in the silicon of the Microchip USB491x hub.
Microchip requested to ignore the device descriptor and decrease that
value to 9 as it was too late to modify that in silicon.
This patch speeds up the USB enummeration process that helps to pass
Apple Carplay certifications and improve the User experience when utilizing
the USB device via Microchip Multihost USB491x Hub.
A new hub quirk HUB_QUIRK_REDUCE_FRAME_INTR_BINTERVAL speeds up
the notification process for Microchip USB491x hub by limiting
the maximum bInterval value to 9.
In the error path after calling dev_set_name(), the device
name is leaked. To fix this, moving dev_set_name() after the
error path and before device_register.
Since commit d927ef5004ef ("perf cs-etm: Add exception level consistency
check"), the exception that was added to Perf will be triggered unless
the following bugfix from OpenCSD is present:
- _Version 1.2.1_:
- __Bugfix__:
ETM4x / ETE - output of context elements to client can in some
circumstances be delayed until after subsequent atoms have been
processed leading to incorrect memory decode access via the client
callbacks. Fixed to flush context elements immediately they are
committed.
Rather than remove the assert and silently fail, just increase the
minimum version requirement to avoid hard to debug issues and
regressions.
Reviewed-by: Ian Rogers <irogers@google.com> Signed-off-by: James Clark <james.clark@arm.com> Tested-by: Leo Yan <leo.yan@linaro.org> Cc: John Garry <john.g.garry@oracle.com> Cc: Mike Leach <mike.leach@linaro.org> Cc: Will Deacon <will@kernel.org> Cc: linux-arm-kernel@lists.infradead.org Link: https://lore.kernel.org/r/20230901133716.677499-1-james.clark@arm.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
A PCI device hot removal may occur while stdev->cdev is held open. The call
to stdev_release() then happens during close or exit, at a point way past
switchtec_pci_remove(). Otherwise the last ref would vanish with the
trailing put_device(), just before return.
At that later point in time, the devm cleanup has already removed the
stdev->mmio_mrpc mapping. Also, the stdev->pdev reference was not a counted
one. Therefore, in DMA mode, the iowrite32() in stdev_release() will cause
a fatal page fault, and the subsequent dma_free_coherent(), if reached,
would pass a stale &stdev->pdev->dev pointer.
Fix by moving MRPC DMA shutdown into switchtec_pci_remove(), after
stdev_kill(). Counting the stdev->pdev ref is now optional, but may prevent
future accidents.
Reproducible via the script at
https://lore.kernel.org/r/20231113212150.96410-1-dns@arista.com
By running a Van Gogh device (Steam Deck), the following message
was noticed in the kernel log:
pci 0000:04:00.3: PCI class overridden (0x0c03fe -> 0x0c03fe) so dwc3 driver can claim this instead of xhci
Effectively this means the quirk executed but changed nothing, since the
class of this device was already the proper one (likely adjusted by newer
firmware versions).
When arm_mhuv2 working with the data protocol transfer mode.
We have split one mhu into two channels, and every channel
include four channel windows, the two channels share
one gic spi interrupt.
There is a problem with the sending scenario.
The first channel will take up 0-3 channel windows, and the second
channel take up 4-7 channel windows. When the first channel send the
data, and the receiver will clear all the four channels status.
Although we only enabled the interrupt on the last channel window with
register CH_INT_EN,the register CHCOMB_INT_ST0 will be 0xf, not be 0x8.
Currently we just clear the last channel windows int status with the
data proctol mode.So after that,the CHCOMB_INT_ST0 status will be 0x7,
not be the 0x0.
Then the second channel send the data, the receiver read the
data, clear all the four channel windows status, trigger the sender
interrupt. But currently the CHCOMB_INT_ST0 register will be 0xf7,
get_irq_chan_comb function will always return the first channel.
So this patch clear all channel windows int status to avoid this interrupt
confusion.
DO NOT access the underlying struct page of an sg table exported
by DMA-buf in dmabuf_imp_to_refs(), this is not allowed.
Please see drivers/dma-buf/dma-buf.c:mangle_sg_table() for details.
Fortunately, here (for special Xen device) we can avoid using
pages and calculate gfns directly from dma addresses provided by
the sg table.
Suggested-by: Daniel Vetter <daniel@ffwll.ch> Signed-off-by: Oleksandr Tyshchenko <oleksandr_tyshchenko@epam.com> Acked-by: Christian König <christian.koenig@amd.com> Reviewed-by: Stefano Stabellini <sstabellini@kernel.org> Acked-by: Daniel Vetter <daniel@ffwll.ch> Link: https://lore.kernel.org/r/20240107103426.2038075-1-olekstysh@gmail.com Signed-off-by: Juergen Gross <jgross@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
As per the Cadence IP document fixed the I2C clock divider value limit from
16 bits instead of 10 bits. Without this change setting up the I2C clock to
low frequencies will not work as the prescaler value might be greater than
10 bit number.
I3C clock divider value is 10 bits only. Updating the macro names for both.
In 'basic' time-travel mode (without =inf-cpu or =ext), we
still get timer interrupts. These can happen at arbitrary
points in time, i.e. while in timer_read(), which pushes
time forward just a little bit. Then, if we happen to get
the interrupt after calculating the new time to push to,
but before actually finishing that, the interrupt will set
the time to a value that's incompatible with the forward,
and we'll crash because time goes backwards when we do the
forwarding.
Fix this by reading the time_travel_time, calculating the
adjustment, and doing the adjustment all with interrupts
disabled.
Reported-by: Vincent Whitchurch <Vincent.Whitchurch@axis.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Richard Weinberger <richard@nod.at> Signed-off-by: Sasha Levin <sashal@kernel.org>
With clang's kernel control flow integrity (kCFI, CONFIG_CFI_CLANG),
indirect call targets are validated against the expected function
pointer prototype to make sure the call target is valid to help mitigate
ROP attacks. If they are not identical, there is a failure at run time,
which manifests as either a kernel panic or thread getting killed. A
warning in clang aims to catch these at compile time, which reveals:
arch/um/drivers/net_kern.c:353:21: warning: incompatible function pointer types initializing 'netdev_tx_t (*)(struct sk_buff *, struct net_device *)' (aka 'enum netdev_tx (*)(struct sk_buff *, struct net_device *)') with an expression of type 'int (struct sk_buff *, struct net_device *)' [-Wincompatible-function-pointer-types-strict]
353 | .ndo_start_xmit = uml_net_start_xmit,
| ^~~~~~~~~~~~~~~~~~
1 warning generated.
->ndo_start_xmit() in 'struct net_device_ops' expects a return type of
'netdev_tx_t', not 'int'. Adjust the return type of uml_net_start_xmit()
to match the prototype's to resolve the warning. While UML does not
currently implement support for kCFI, it could in the future, which
means this warning becomes a fatal CFI failure at run time.
Reported-by: kernel test robot <lkp@intel.com> Closes: https://lore.kernel.org/oe-kbuild-all/202310031340.v1vPh207-lkp@intel.com/ Acked-by: Anton Ivanov <anton.ivanov@cambridgegreys.com> Signed-off-by: Nathan Chancellor <nathan@kernel.org> Signed-off-by: Richard Weinberger <richard@nod.at> Signed-off-by: Sasha Levin <sashal@kernel.org>
The threads allocated inside the kernel have only a single page of
stack. Unfortunately, the vfprintf function in standard glibc may use
too much stack-space, overflowing it.
To make os_info safe to be used by helper threads, use the kernel
vscnprintf function into a smallish buffer and write out the information
to stderr.
Signed-off-by: Benjamin Berg <benjamin@sipsolutions.net> Signed-off-by: Richard Weinberger <richard@nod.at> Signed-off-by: Sasha Levin <sashal@kernel.org>
When OMTP headset plugin the headset jack of CX8070 and SN6160 sound cards,
the headset type detection circuit will recognize the headset type as CTIA.
At this point, plugout and plugin the headset will get the correct headset
type as OMTP.
The reason for the failure of headset type recognition is that the sound
card creation will enable the VREF voltage of the headset mic, which
interferes with the headset type automatic detection circuit. Plugout and
plugin the headset will restart the headset detection and get the correct
headset type.
The patch is disable the VREF voltage when the headset is not present, and
will enable the VREF voltage when the headset is present.
These chips needs the same fix. This was previously not seen
on then since the AGP aperture expanded the system aperture,
but this showed up again when AGP was disabled.
Fix the following about iterator use:
drivers/gpu/drm/amd/amdgpu/../amdkfd/kfd_topology.c:1456 kfd_add_peer_prop() warn: iterator used outside loop: 'iolink3'
Cc: Felix Kuehling <Felix.Kuehling@amd.com> Cc: Christian König <christian.koenig@amd.com> Cc: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com> Reviewed-by: Felix Kuehling <felix.kuehling@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Return value of container_of(...) can't be null, so null check is not
required for 'fence'. Hence drop its NULL check.
Fixes the below:
drivers/gpu/drm/amd/amdgpu/amdgpu_amdkfd_fence.c:93 to_amdgpu_amdkfd_fence() warn: can 'fence' even be NULL?
Cc: Felix Kuehling <Felix.Kuehling@amd.com> Cc: Christian König <christian.koenig@amd.com> Cc: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com> Reviewed-by: Felix Kuehling <felix.kuehling@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fixes the below:
drivers/gpu/drm/amd/amdgpu/amdgpu_ucode.c:1404 amdgpu_ucode_request() warn: '*fw' from request_firmware() not released on lines: 1404.
Cc: Mario Limonciello <mario.limonciello@amd.com> Cc: Lijo Lazar <lijo.lazar@amd.com> Cc: Christian König <christian.koenig@amd.com> Cc: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Since, it causes a regression in which eDP displays with PSR support,
but no Replay support (Sink support <= 0x03), fail to enable PSR and
consequently all IGT amd_psr tests fail. So, revert this until a more
suitable fix can be found.
This got brought back accidently with the backmerge.
Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Ivan Lipski <ivlipski@amd.com> Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Change the rules for amdgpu_sync_resv to let KFD synchronize with VM
fences on page table reservations. This fixes intermittent memory
corruption after evictions when using amdgpu_vm_handle_moved to update
page tables for VM mappings managed through render nodes.
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
[How]
- In set_usb4_req_bw_req(), link->dpia_bw_alloc_config.response_ready
flag should be reset before writing DPCD REQUEST_BW.
- Fix the granularity for value of 2 in get_bw_granularity().
- Removed bandwidth allocation support display fw boot option as
the fw would read feature enable status from bios.
- Clean up DPIA_EST_BW_CHANGED and DPIA_BW_REQ_SUCCESS cases in
dpia_handle_bw_alloc_response().
- Removed allocate_usb4_bw and deallocate_usb4_bw.
- Optimized loop in get_lowest_dpia_index().
- Updated link_dp_dpia_allocate_usb4_bandwidth_for_stream() and
set_usb4_req_bw_req() to always issue request bw.
To be compatible with SCU firmware based on 1.15 a different clock
routing for LVDS is needed.
Signed-off-by: Oliver F. Brown <oliver.brown@oss.nxp.com> Signed-off-by: Ranjani Vaidyanathan <ranjani.vaidyanathan@nxp.com> Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com> Reviewed-by: Abel Vesa <abel.vesa@linaro.org> Link: https://lore.kernel.org/r/20231218122407.2757175-1-alexander.stein@ew.tq-group.com/ Signed-off-by: Abel Vesa <abel.vesa@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
[Description]
There is a corner case where the symclk otg flag is cleared
when disabling the phantom pipe for subvp (because the phantom
and main pipe share the same link). This is undesired because
we need the maintain the correct symclk otg flag state for
the main pipe.
For now only clear the flag only for HDMI signal type, since
it's only set for HDMI signal type (phantom is virtual). The
ideal solution is to not clear it if the stream is phantom but
currently there's a bug that doesn't allow us to do this. Once
this issue is fixed the proper fix can be implemented.
Reviewed-by: Samson Tam <samson.tam@amd.com> Acked-by: Wayne Lin <wayne.lin@amd.com> Signed-off-by: Alvin Lee <alvin.lee2@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
[Why]
This variable currently overflows after about 71 minutes. This doesn't
cause any known functional issues but it does make debugging more
difficult.
[How]
Make it a 64-bit variable.
Reviewed-by: Aric Cyr <aric.cyr@amd.com> Acked-by: Wayne Lin <wayne.lin@amd.com> Signed-off-by: Josip Pavic <josip.pavic@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
WDTCTRL bit 3 sets the mode choice for the clock input of IT8784/IT8786.
Some motherboards require this bit to be set to 1 (= PCICLK mode),
otherwise the watchdog functionality gets broken. The BIOS of those
motherboards sets WDTCTRL bit 3 already to 1.
Instead of setting all bits of WDTCTRL to 0 by writing 0x00 to it, keep
bit 3 of it unchanged for IT8784/IT8786 chips. In this way, bit 3 keeps
the status as set by the BIOS of the motherboard.
Watchdog tests have been successful with this patch with the following
systems:
IT8784: Thomas-Krenn LES plus v2 (YANLING YL-KBRL2 V2)
IT8786: Thomas-Krenn LES plus v3 (YANLING YL-CLU L2)
IT8786: Thomas-Krenn LES network 6L v2 (YANLING YL-CLU6L)
In cases where mapping of mpmu/apmu/apbc registers fails, the code path
does not handle the failure gracefully, potentially leading to a memory
leak. This fix ensures proper cleanup by freeing the allocated memory
for 'pxa_unit' before returning.
In cases where kcalloc() fails for the 'clk_data->clks' allocation, the
code path does not handle the failure gracefully, potentially leading
to a memory leak. This fix ensures proper cleanup by freeing the
allocated memory for 'clk_data' before returning.
Issue: during evict or validate happened on amdgpu_bo, the 'from' and
'to' is always same in ftrace event of amdgpu_bo_move
where calling the 'trace_amdgpu_bo_move', the comment says move_notify
is called before move happens, but actually it is called after move
happens, here the new_mem is same as bo->resource
Fix: move trace_amdgpu_bo_move from move_notify to amdgpu_bo_move
Signed-off-by: Wang, Beyond <Wang.Beyond@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
For YUV cases, setting the required format bits was missed
out in the register programming. Lets fix it now in preparation
of adding YUV formats support for writeback.
changes in v2:
- dropped the fixes tag as its not a fix but adding
new functionality
MES provides the driver a call to explicitly flush stale process memory
within the MES to avoid a race condition that results in a fatal
memory violation.
When SET_SHADER_DEBUGGER is called, the driver passes a memory address
that represents a process context address MES uses to keep track of
future per-process calls.
Normally, MES will purge its process context list when the last queue
has been removed. The driver, however, can call SET_SHADER_DEBUGGER
regardless of whether a queue has been added or not.
If SET_SHADER_DEBUGGER has been called with no queues as the last call
prior to process termination, the passed process context address will
still reside within MES.
On a new process call to SET_SHADER_DEBUGGER, the driver may end up
passing an identical process context address value (based on per-process
gpu memory address) to MES but is now pointing to a new allocated buffer
object during KFD process creation. Since the MES is unaware of this,
access of the passed address points to the stale object within MES and
triggers a fatal memory violation.
The solution is for KFD to explicitly flush the process context address
from MES on process termination.
Note that the flush call and the MES debugger calls use the same MES
interface but are separated as KFD calls to avoid conflicting with each
other.
Signed-off-by: Jonathan Kim <jonathan.kim@amd.com> Tested-by: Alice Wong <shiwei.wong@amd.com> Reviewed-by: Eric Huang <jinhuieric.huang@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
[Description]
- When we're in a no plane config, DCN is always asserting
P-State allow
- This creates a scenario where the P-State blackout can start
just as VUPDATE takes place and transitions the DCN config to
a one where one or more HUBP's are active which can result in
underflow
- To fix this issue, force p-state disallow and unforce after
the transition from no planes case -> one or more planes active
Reviewed-by: Samson Tam <samson.tam@amd.com> Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com> Signed-off-by: Alvin Lee <alvin.lee2@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
[Description]
For mode programming we want to extend the prefetch as much as possible
(up to oto, or as long as we can for equ) if we're not already applying
the 60us prefetch requirement. This is to avoid intermittent underflow
issues during prefetch.
The prefetch extension is applied under the following scenarios:
1. We're in prefetch mode 1 (i.e. we don't support MCLK switch in blank)
2. We're using subvp or drr methods of p-state switch, in which case we
we don't care if prefetch takes up more of the blanking time
Mode programming typically chooses the smallest prefetch time possible
(i.e. highest bandwidth during prefetch) presumably to create margin between
p-states / c-states that happen in vblank and prefetch. Therefore we only
apply this prefetch extension when p-state in vblank is not required (UCLK
p-states take up the most vblank time).
Reviewed-by: Jun Lei <jun.lei@amd.com> Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com> Signed-off-by: Alvin Lee <alvin.lee2@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
we need to refine check_is_responsed() to remove the mutext_lock, each
cmd has a monotonically increasing id, and cmds are executed
sequentially, so we can check the id of the last reponsed cmd, then
determine whether a command has been responded or not.
Signed-off-by: Ming Qian <ming.qian@nxp.com> CC: Xiaolei Wang <xiaolei.wang@windriver.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Sasha Levin <sashal@kernel.org>
Releasing the `priv->lock` while iterating the `priv->multicast_list` in
`ipoib_mcast_join_task()` opens a window for `ipoib_mcast_dev_flush()` to
remove the items while in the middle of iteration. If the mcast is removed
while the lock was dropped, the for loop spins forever resulting in a hard
lockup (as was reported on RHEL 4.18.0-372.75.1.el8_6 kernel):
Task A (kworker/u72:2 below) | Task B (kworker/u72:0 below)
-----------------------------------+-----------------------------------
ipoib_mcast_join_task(work) | ipoib_ib_dev_flush_light(work)
spin_lock_irq(&priv->lock) | __ipoib_ib_dev_flush(priv, ...)
list_for_each_entry(mcast, | ipoib_mcast_dev_flush(dev = priv->dev)
&priv->multicast_list, list) |
ipoib_mcast_join(dev, mcast) |
spin_unlock_irq(&priv->lock) |
| spin_lock_irqsave(&priv->lock, flags)
| list_for_each_entry_safe(mcast, tmcast,
| &priv->multicast_list, list)
| list_del(&mcast->list);
| list_add_tail(&mcast->list, &remove_list)
| spin_unlock_irqrestore(&priv->lock, flags)
spin_lock_irq(&priv->lock) |
| ipoib_mcast_remove_list(&remove_list)
(Here, `mcast` is no longer on the | list_for_each_entry_safe(mcast, tmcast,
`priv->multicast_list` and we keep | remove_list, list)
spinning on the `remove_list` of | >>> wait_for_completion(&mcast->done)
the other thread which is blocked |
and the list is still valid on |
it's stack.)
Fix this by keeping the lock held and changing to GFP_ATOMIC to prevent
eventual sleeps.
Unfortunately we could not reproduce the lockup and confirm this fix but
based on the code review I think this fix should address such lockups.
Based on grepping through the source code this driver appears to be
missing a call to drm_atomic_helper_shutdown() at system shutdown time
and at driver unbind time. Among other things, this means that if a
panel is in use that it won't be cleanly powered off at system
shutdown time.
The fact that we should call drm_atomic_helper_shutdown() in the case
of OS shutdown/restart and at driver remove (or unbind) time comes
straight out of the kernel doc "driver instance overview" in
drm_drv.c.
A few notes about this fix:
- When adding drm_atomic_helper_shutdown() to the unbind path, I added
it after drm_kms_helper_poll_fini() since that's when other drivers
seemed to have it.
- Technically with a previous patch, ("drm/atomic-helper:
drm_atomic_helper_shutdown(NULL) should be a noop"), we don't
actually need to check to see if our "drm" pointer is NULL before
calling drm_atomic_helper_shutdown(). We'll leave the "if" test in,
though, so that this patch can land without any dependencies. It
could potentially be removed later.
- This patch also makes sure to set the drvdata to NULL in the case of
bind errors to make sure that shutdown can't access freed data.
Suggested-by: Maxime Ripard <mripard@kernel.org> Reviewed-by: Maxime Ripard <mripard@kernel.org> Signed-off-by: Douglas Anderson <dianders@chromium.org> Tested-by: Marek Szyprowski <m.szyprowski@samsung.com> Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Inki Dae <inki.dae@samsung.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
It needs to add missing gcing flag on page during block migration,
in order to garantee migrated data be persisted during checkpoint,
otherwise out-of-order persistency between data and node may cause
data corruption after SPOR.
Similar issue was fixed by commit 2d1fe8a86bf5 ("f2fs: fix to tag
gcing flag on page during file defragment").
The EliteDesk 800 G6 stores a raw WMI string within the ACPI object in its
BIOS corresponding to one instance of HPBIOS_PlatformEvents.Name. This is
evidently a valid way of representing a WMI data item as far as the
Microsoft ACPI-WMI mapper is concerned, but is preventing the driver from
loading.
This seems quite rare, but add support for such strings. Treating this as a
quirk pretty much means adding that support anyway.
Also clean up an oversight in update_numeric_sensor_from_wobj() in which
the result of hp_wmi_strdup() was being used without error checking.
Setting the fan speed is only valid in manual mode; it is not possible
to set the fan's speed in automatic mode.
Return error when attempting to set the fan speed in automatic mode.
Supported media bus codes on the resizer sink pad are identical to the
ISP source pad. The .enum_mbus_code() handler thus delegates the
enumeration to the ISP's operation. This is problematic for two
reasons:
- Format enumeration on the ISP source pad is dependent on the format
configured on the ISP sink pad for the same subdev state (TRY or
ACTIVE), while format enumeration on the resizer sink pad should
return all formats supported by the resizer subdev, regardless of the
ISP configuration.
- Delegating the operation involves creating a fake v4l2_subdev_state on
the stack to pass to the ISP .enum_mbus_code() handler. This gets in
the way of evolution of both the ISP enumeration handler and, more
generally, the V4L2 subdev state infrastructure.
Fix those two issues by implementing format enumeration manually for the
resizer.
In rkisp1_isp_stop() and rkisp1_csi_disable() the driver masks the
interrupts and then apparently assumes that the interrupt handler won't
be running, and proceeds in the stop procedure. This is not the case, as
the interrupt handler can already be running, which would lead to the
ISP being disabled while the interrupt handler handling a captured
frame.
This brings up two issues: 1) the ISP could be powered off while the
interrupt handler is still running and accessing registers, leading to
board lockup, and 2) the interrupt handler code and the code that
disables the streaming might do things that conflict.
It is not clear to me if 2) causes a real issue, but 1) can be seen with
a suitable delay (or printk in my case) in the interrupt handler,
leading to board lockup.
Link: https://lore.kernel.org/r/20231207-rkisp-irq-fix-v3-4-358a2c871a3c@ideasonboard.com Tested-by: Adam Ford <aford173@gmail.com> #imx8mp-beacon Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com> Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The IRQ handler rkisp1_isr() calls sub-handlers, all of which returns an
irqreturn_t value, but rkisp1_isr() ignores those values and always
returns IRQ_HANDLED.
Fix this by collecting the return values, and returning IRQ_HANDLED or
IRQ_NONE as appropriate.
Link: https://lore.kernel.org/r/20231207-rkisp-irq-fix-v3-2-358a2c871a3c@ideasonboard.com Tested-by: Adam Ford <aford173@gmail.com> #imx8mp-beacon Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com> Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In all known platforms the ISP has dedicated IRQ lines, but for some
reason the driver uses IRQF_SHARED.
Supporting IRQF_SHARED properly requires handling interrupts even when
our device is disabled, and the driver does not handle this. To avoid
adding such code, and to be sure the driver won't accidentally be used
in a platform with shared interrupts, let's drop the IRQF_SHARED flag.
Link: https://lore.kernel.org/r/20231207-rkisp-irq-fix-v3-1-358a2c871a3c@ideasonboard.com Tested-by: Adam Ford <aford173@gmail.com> #imx8mp-beacon Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com> Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The Qualcomm SM8650 platform comes with a DisplayPort controller
with a different base offset than the previous SM8550 SoC,
add support for this in the DisplayPort driver.
When using 32 bit RGB formats, the RGA on the rk3568 produces wrong
colors as the wrong color channels are read or written. The reason is
that the format description for the channel swizzeling is wrong and the
wrong bits are configured. For example, when converting ARGB32 to NV12,
the alpha channel is used as blue channel.. This doesn't happen if the
color format is the same on both sides.
Fix the color_swap settings of the formats to correctly handle 32 bit
RGB formats.
For RGA_COLOR_FMT_XBGR8888, the RGA_COLOR_ALPHA_SWAP bit doesn't have an
effect. Thus, it isn't possible to handle the V4L2_PIX_FMT_XRGB32. Thus,
it is removed from the list of supported formats.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Sasha Levin <sashal@kernel.org>
The function stk1160_dbg gets called too many times, which causes
the output to get flooded with messages. Since stk1160_dbg uses
printk, it is now replaced with printk_ratelimited.
Suggested-by: Phillip Potter <phil@philpotter.co.uk> Signed-off-by: Ghanshyam Agrawal <ghanshyam1898@gmail.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Sasha Levin <sashal@kernel.org>
After reading the code, I think this is what happens:
We have a DSI host defined in the device tree and a DSI peripheral under
that host (i.e. an i2c device using the DSI as data bus doesn't exhibit
this behavior).
The host driver calls mipi_dsi_host_register(), which causes (via a few
functions) mipi_dsi_device_add() to be called for the DSI peripheral. So
now we have a DSI device under the host, but attach hasn't been called.
Normally the probing of the devices continues, and eventually the DSI
peripheral's driver will call mipi_dsi_attach(), attaching the
peripheral.
However, if the host driver's probe encounters an error after calling
mipi_dsi_host_register(), and before the peripheral has called
mipi_dsi_attach(), the host driver will do cleanups and return an error
from its probe function. The cleanups include calling
mipi_dsi_host_unregister().
mipi_dsi_host_unregister() will call two functions for all its DSI
peripheral devices: mipi_dsi_detach() and mipi_dsi_device_unregister().
The latter makes sense, as the device exists, but the former may be
wrong as attach has not necessarily been done.
To fix this, track the attached state of the peripheral, and only detach
from mipi_dsi_host_unregister() if the peripheral was attached.
Note that I have only tested this with a board with an i2c DSI
peripheral, not with a "pure" DSI peripheral.
However, slightly related, the unregister machinery still seems broken.
E.g. if the DSI host driver is unbound, it'll detach and unregister the
DSI peripherals. After that, when the DSI peripheral driver unbound
it'll call detach either directly or using the devm variant, leading to
a crash. And probably the driver will crash if it happens, for some
reason, to try to send a message via the DSI bus.
But that's another topic.
Tested-by: H. Nikolaus Schaller <hns@goldelico.com> Acked-by: Maxime Ripard <mripard@kernel.org> Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com> Tested-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com> Link: https://patchwork.freedesktop.org/patch/msgid/20230921-dsi-detach-fix-v1-1-d0de2d1621d9@ideasonboard.com Signed-off-by: Sasha Levin <sashal@kernel.org>
drivers/gpu/drm/drm_framebuffer.c:654 drm_mode_getfb2_ioctl() error: uninitialized symbol 'ret'.
'ret' is possibly not set when there are no errors, causing the error
above. I can't say if that ever happens in real-life, but in any case I
think it is good to initialize 'ret' to 0.
projects / thirdparty / kernel / stable.git / log
