Commit 39ce8150a079 ("pinctrl: baytrail: Serialize all register access")
added a spinlock around all register accesses because:
"There is a hardware issue in Intel Baytrail where concurrent GPIO register
access might result reads of 0xffffffff and writes might get dropped
completely."
Testing has shown that this does not catch all cases, there are still
2 problems remaining
1) The original fix uses a spinlock per byt_gpio device / struct,
additional testing has shown that this is not sufficient concurent
accesses to 2 different GPIO banks also suffer from the same problem.
This commit fixes this by moving to a single global lock.
2) The original fix did not add a lock around the register accesses in
the suspend/resume handling.
Since pinctrl-baytrail.c is using normal suspend/resume handlers,
interrupts are still enabled during suspend/resume handling. Nothing
should be using the GPIOs when they are being taken down, _but_ the
GPIOs themselves may still cause interrupts, which are likely to
use (read) the triggering GPIO. So we need to protect against
concurrent GPIO register accesses in the suspend/resume handlers too.
This commit fixes this by adding the missing spin_lock / unlock calls.
The 2 fixes together fix the Acer Switch 10 SW5-012 getting completely
confused after a suspend resume. The DSDT for this device has a bug
in its _LID method which reprograms the home and power button trigger-
flags requesting both high and low _level_ interrupts so the IRQs for
these 2 GPIOs continuously fire. This combined with the saving of
registers during suspend, triggers concurrent GPIO register accesses
resulting in saving 0xffffffff as pconf0 value during suspend and then
when restoring this on resume the pinmux settings get all messed up,
resulting in various I2C busses being stuck, the wifi no longer working
and often the tablet simply not coming out of suspend at all.
Cc: stable@vger.kernel.org Fixes: 39ce8150a079 ("pinctrl: baytrail: Serialize all register access") Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A break interrupt will be generated if the RX line was pulled low, which
means some abnomal behaviors occurred of the UART. In this case, we still
need to clear this break interrupt status, otherwise it will cause irq
storm to crash the whole system.
The "auto-attach" handler function `gsc_hpdi_auto_attach()` calls
`dma_alloc_coherent()` in a loop to allocate some DMA data buffers, and
also calls it to allocate a buffer for a DMA descriptor chain. However,
it does not check the return value of any of these calls. Change
`gsc_hpdi_auto_attach()` to return `-ENOMEM` if any of these
`dma_alloc_coherent()` calls fail. This will result in the comedi core
calling the "detach" handler `gsc_hpdi_detach()` as part of the
clean-up, which will call `gsc_hpdi_free_dma()` to free any allocated
DMA coherent memory buffers.
At least on the HP Envy x360 15-cp0xxx model the WMI interface
for HPWMI_FEATURE2_QUERY requires an outsize of at least 128 bytes,
otherwise it fails with an error code 5 (HPWMI_RET_INVALID_PARAMETERS):
Dec 06 00:59:38 kernel: hp_wmi: query 0xd returned error 0x5
We do not care about the contents of the buffer, we just want to know
if the HPWMI_FEATURE2_QUERY command is supported.
This commits bumps the buffer size, fixing the error.
Fixes: 8a1513b4932 ("hp-wmi: limit hotkey enable") Cc: stable@vger.kernel.org BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1520703 Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 6cac7866c2741 ("intel_th: msu: Add a sysfs attribute to trigger
window switch") adds a NULL pointer dereference in the case when there are
no windows allocated:
Commit aac8da65174a ("intel_th: msu: Start handling IRQs") implicitly
relies on the use of devm_request_irq() to subsequently free the irqs on
device removal, but in case of the pci_free_irq_vectors() API, the
handlers need to be freed before it is called. Therefore, at the moment
the driver's remove path trips a BUG_ON(irq_has_action()):
When disconnecting a USB hub that has some child device(s) connected to it
(such as a USB mouse), then the stack tries to clear halt and
reset device(s) which are _already_ physically disconnected.
The issue has been reproduced with:
CPU: IMX6D5EYM10AD or MCIMX6D5EYM10AE.
SW: U-Boot 2019.07 and kernel 4.19.40.
CPU: HP Proliant Microserver Gen8.
SW: Linux version 4.2.3-300.fc23.x86_64
In this situation there will be error bit for MMF active yet the
CERR equals EHCI_TUNE_CERR + halt. Existing implementation
interprets this as a stall [1] (chapter 8.4.5).
The possible conditions when the MMF will be active + halt
can be found from [2] (Table 4-13).
Fix for the issue is to check whether MMF is active and PID Code is
IN before checking for the stall. If these conditions are true then
it is not a stall.
What happens after the fix is that when disconnecting a hub with
attached device(s) the situation is not interpret as a stall.
Since commit 0a432dcbeb32 ("mm: shrinker: make shrinker not depend on
memcg kmem"), shrinkers' idr is protected by CONFIG_MEMCG instead of
CONFIG_MEMCG_KMEM, so it makes no sense to protect shrinker idr replace
with CONFIG_MEMCG_KMEM.
And in the CONFIG_MEMCG && CONFIG_SLOB case, shrinker_idr contains only
shrinker, and it is deferred_split_shrinker. But it is never actually
called, since idr_replace() is never compiled due to the wrong #ifdef.
The deferred_split_shrinker all the time is staying in half-registered
state, and it's never called for subordinate mem cgroups.
Link: http://lkml.kernel.org/r/1575486978-45249-1-git-send-email-yang.shi@linux.alibaba.com Fixes: 0a432dcbeb32 ("mm: shrinker: make shrinker not depend on memcg kmem") Signed-off-by: Yang Shi <yang.shi@linux.alibaba.com> Reviewed-by: Kirill Tkhai <ktkhai@virtuozzo.com> Acked-by: Michal Hocko <mhocko@suse.com> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Shakeel Butt <shakeelb@google.com> Cc: Roman Gushchin <guro@fb.com> Cc: <stable@vger.kernel.org> [5.4+] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The scheduler code calling cpufreq_update_util() may run during CPU
offline on the target CPU after the IRQ work lists have been flushed
for it, so the target CPU should be prevented from running code that
may queue up an IRQ work item on it at that point.
Unfortunately, that may not be the case if dvfs_possible_from_any_cpu
is set for at least one cpufreq policy in the system, because that
allows the CPU going offline to run the utilization update callback
of the cpufreq governor on behalf of another (online) CPU in some
cases.
If that happens, the cpufreq governor callback may queue up an IRQ
work on the CPU running it, which is going offline, and the IRQ work
may not be flushed after that point. Moreover, that IRQ work cannot
be flushed until the "offlining" CPU goes back online, so if any
other CPU calls irq_work_sync() to wait for the completion of that
IRQ work, it will have to wait until the "offlining" CPU is back
online and that may not happen forever. In particular, a system-wide
deadlock may occur during CPU online as a result of that.
The failing scenario is as follows. CPU0 is the boot CPU, so it
creates a cpufreq policy and becomes the "leader" of it
(policy->cpu). It cannot go offline, because it is the boot CPU.
Next, other CPUs join the cpufreq policy as they go online and they
leave it when they go offline. The last CPU to go offline, say CPU3,
may queue up an IRQ work while running the governor callback on
behalf of CPU0 after leaving the cpufreq policy because of the
dvfs_possible_from_any_cpu effect described above. Then, CPU0 is
the only online CPU in the system and the stale IRQ work is still
queued on CPU3. When, say, CPU1 goes back online, it will run
irq_work_sync() to wait for that IRQ work to complete and so it
will wait for CPU3 to go back online (which may never happen even
in principle), but (worse yet) CPU0 is waiting for CPU1 at that
point too and a system-wide deadlock occurs.
To address this problem notice that CPUs which cannot run cpufreq
utilization update code for themselves (for example, because they
have left the cpufreq policies that they belonged to), should also
be prevented from running that code on behalf of the other CPUs that
belong to a cpufreq policy with dvfs_possible_from_any_cpu set and so
in that case the cpufreq_update_util_data pointer of the CPU running
the code must not be NULL as well as for the CPU which is the target
of the cpufreq utilization update in progress.
Accordingly, change cpufreq_this_cpu_can_update() into a regular
function in kernel/sched/cpufreq.c (instead of a static inline in a
header file) and make it check the cpufreq_update_util_data pointer
of the local CPU if dvfs_possible_from_any_cpu is set for the target
cpufreq policy.
Also update the schedutil governor to do the
cpufreq_this_cpu_can_update() check in the non-fast-switch
case too to avoid the stale IRQ work issues.
Fixes: 99d14d0e16fa ("cpufreq: Process remote callbacks from any CPU if the platform permits") Link: https://lore.kernel.org/linux-pm/20191121093557.bycvdo4xyinbc5cb@vireshk-i7/ Reported-by: Anson Huang <anson.huang@nxp.com> Tested-by: Anson Huang <anson.huang@nxp.com> Cc: 4.14+ <stable@vger.kernel.org> # 4.14+ Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Acked-by: Viresh Kumar <viresh.kumar@linaro.org> Tested-by: Peng Fan <peng.fan@nxp.com> (i.MX8QXP-MEK) Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Memory regions that are reserved using efi_mem_reserve_persistent()
are recorded in a special EFI config table which survives kexec,
allowing the incoming kernel to honour them as well. However,
such reservations are not visible in /proc/iomem, and so the kexec
tools that load the incoming kernel and its initrd into memory may
overwrite these reserved regions before the incoming kernel has a
chance to reserve them from further use.
Address this problem by adding these reservations to /proc/iomem as
they are created. Note that reservations that are inherited from a
previous kernel are memblock_reserve()'d early on, so they are already
visible in /proc/iomem.
The problem comes from the error path which calls
irq_dispose_mapping() while the IRQ has been requested with
devm_request_irq().
IRQ doesn't need to be mapped with irq_of_parse_and_map(). The only
need is to get the IRQ virtual number. For that, use
of_irq_to_resource() instead of the
irq_of_parse_and_map()/irq_dispose_mapping() pair.
If a transaction error happens in vhci_recv_ret_submit(), event
handler closes connection and changes port status to kick hub_event.
Then hub tries to flush the endpoint URBs, but that causes infinite
loop between usb_hub_flush_endpoint() and vhci_urb_dequeue() because
"vhci_priv" in vhci_urb_dequeue() was already released by
vhci_recv_ret_submit() before a transmission error occurred. Thus,
vhci_urb_dequeue() terminates early and usb_hub_flush_endpoint()
continuously calls vhci_urb_dequeue().
The root cause of this issue is that vhci_recv_ret_submit()
terminates early without giving back URB when transaction error
occurs in vhci_recv_ret_submit(). That causes the error URB to still
be linked at endpoint list without “vhci_priv".
So, in the case of transaction error in vhci_recv_ret_submit(),
unlink URB from the endpoint, insert proper error code in
urb->status and give back URB.
Reported-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com> Tested-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com> Signed-off-by: Suwan Kim <suwan.kim027@gmail.com> Cc: stable <stable@vger.kernel.org> Acked-by: Shuah Khan <skhan@linuxfoundation.org> Link: https://lore.kernel.org/r/20191213023055.19933-3-suwan.kim027@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When vhci uses SG and receives data whose size is smaller than SG
buffer size, it tries to receive more data even if it acutally
receives all the data from the server. If then, it erroneously adds
error event and triggers connection shutdown.
vhci-hcd should check if it received all the data even if there are
more SG entries left. So, check if it receivces all the data from
the server in for_each_sg() loop.
Fixes: ea44d190764b ("usbip: Implement SG support to vhci-hcd and stub driver") Reported-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com> Tested-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com> Signed-off-by: Suwan Kim <suwan.kim027@gmail.com> Acked-by: Shuah Khan <skhan@linuxfoundation.org> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20191213023055.19933-2-suwan.kim027@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The MCR[LPMACK] read-only bit indicates that FlexCAN is in a lower-power
mode (Disabled mode, Doze mode, Stop mode).
The CPU can poll this bit to know when FlexCAN has actually entered low
power mode. The low power enter/exit acknowledgment helper will reduce
code duplication for disabled mode, doze mode and stop mode.
Tested-by: Sean Nyekjaer <sean@geanix.com> Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
In addition to using vcsi regulator for the display, looks like droid4 is
using vcsi regulator to trigger off mode internally with the PMIC firmware
when the SoC enters deeper idle states. This is configured in the Motorola
Mapphone Linux kernel sources as "zerov_regulator".
As we currently don't support off mode during idle for omap4, we must
prevent vcsi from being disabled when the display is blanked to prevent
the PMIC change to off mode. Otherwise the device will hang on entering
idle when the display is blanked.
Before commit 089b3f61ecfc ("regulator: core: Let boot-on regulators be
powered off"), the boot-on regulators never got disabled like they should
and vcsi did not get turned off on idle.
Let's fix the issue by setting vcsi to always-on for now. Later on we may
want to claim the vcsi regulator also in the PM code if needed.
Fixes: 089b3f61ecfc ("regulator: core: Let boot-on regulators be powered off") Cc: Merlijn Wajer <merlijn@wizzup.org> Cc: Pavel Machek <pavel@ucw.cz> Cc: Sebastian Reichel <sre@kernel.org> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The stack overflow happens because get_tod_clock_monotonic() gets called
by ftrace but itself calls preempt_{disable,enable}(), which leads to a
endless recursion. Fix this by using preempt_{disable,enable}_notrace().
The boolean variable pasid_mapping_needed is not initialized and
there are code paths that do not assign it any value before it is
is read later. Fix this by initializing pasid_mapping_needed to
false.
Addresses-Coverity: ("Uninitialized scalar variable") Fixes: 6817bf283b2b ("drm/amdgpu: grab the id mgr lock while accessing passid_mapping") Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
To fix a regression on the Cadence SPI driver, this patch reverts
commit 6046f5407ff0 ("spi: cadence: Fix default polarity of native
chipselect").
This patch was not the correct fix for the issue. The SPI framework
calls the set_cs line with the logic level it desires on the chip select
line, as such the old is_high handling was correct. However, this was
broken by the fact that before commit 3e5ec1db8bfe ("spi: Fix SPI_CS_HIGH
setting when using native and GPIO CS") all controllers that offered
the use of a GPIO chip select had SPI_CS_HIGH applied, even for hardware
chip selects. This caused the value passed into the driver to be inverted.
Which unfortunately makes it look like a logical enable the chip select
value.
Since the core was corrected to not unconditionally apply SPI_CS_HIGH,
the Cadence driver, whilst using the hardware chip select, will deselect
the chip select every time we attempt to communicate with the device,
which results in failed communications.
Fixes: 3e5ec1db8bfe ("spi: Fix SPI_CS_HIGH setting when using native and GPIO CS") Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com> Acked-by: Linus Walleij <linus.walleij@linaro.org> Link: https://lore.kernel.org/r/20191126164140.6240-1-ckeepax@opensource.cirrus.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
This patch reverts commit 6e0a32d6f376 ("spi: dw: Fix default polarity
of native chipselect").
The SPI framework always called the set_cs callback with the logic
level it desired on the chip select line, which is what the drivers
original handling supported. commit f3186dd87669 ("spi: Optionally
use GPIO descriptors for CS GPIOs") changed these symantics, but only
in the case of drivers that also support GPIO chip selects, to true
meaning apply slave select rather than logic high. This left things in
an odd state where a driver that only supports hardware chip selects,
the core would handle polarity but if the driver supported GPIOs as
well the driver should handle polarity. At this point the reverted
change was applied to change the logic in the driver to match new
system.
This was then broken by commit 3e5ec1db8bfe ("spi: Fix SPI_CS_HIGH
setting when using native and GPIO CS") which reverted the core back
to consistently calling set_cs with a logic level.
This fix reverts the driver code back to its original state to match
the current core code. This is probably a better fix as a) the set_cs
callback is always called with consistent symantics and b) the
inversion for SPI_CS_HIGH can be handled in the core and doesn't need
to be coded in each driver supporting it.
Fixes: 3e5ec1db8bfe ("spi: Fix SPI_CS_HIGH setting when using native and GPIO CS") Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com> Acked-by: Linus Walleij <linus.walleij@linaro.org> Link: https://lore.kernel.org/r/20191127153936.29719-1-ckeepax@opensource.cirrus.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Thanks Paolo Pisati for pointing out the original patchset where this
appeared.
Fixes: 65190f77424d (selftests/tls: add a test for fragmented messages) Reported-by: Paolo Pisati <paolo.pisati@canonical.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com> Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Stop Mode is entered when Stop Mode is requested at chip level and
MCR[LPM_ACK] is asserted by the FlexCAN.
Double check with IP owner, the MCR[LPM_ACK] bit should be polled for
stop mode acknowledgment, not the acknowledgment from chip level which
is used to gate flexcan clocks.
This patch depends on:
b7603d080ffc ("can: flexcan: add low power enter/exit acknowledgment helper")
When suspending, and there is still CAN traffic on the interfaces the
flexcan immediately wakes the platform again. As it should :-). But it
throws this error msg:
[ 3169.378661] PM: noirq suspend of devices failed
On the way down to suspend the interface that throws the error message
calls flexcan_suspend() but fails to call flexcan_noirq_suspend(). That
means flexcan_enter_stop_mode() is called, but on the way out of suspend
the driver only calls flexcan_resume() and skips flexcan_noirq_resume(),
thus it doesn't call flexcan_exit_stop_mode(). This leaves the flexcan
in stop mode, and with the current driver it can't recover from this
even with a soft reboot, it requires a hard reboot.
This patch fixes the deadlock when using self wakeup, by calling
flexcan_exit_stop_mode() from flexcan_resume() instead of
flexcan_noirq_resume().
This also fixes another issue: CAN frames are received out-of-order in
first IRQ handler run after wakeup.
The problem is that the wakeup latency from frame reception to the IRQ
handler (where the CAN frames are sorted by timestamp) is much bigger
than the time stamp counter wrap around time. This means it's
impossible to sort the CAN frames by timestamp.
The reason is that the controller exits stop mode during noirq resume,
which means it receives frames immediately, but interrupt handling is
still not possible.
So exit stop mode during resume stage instead of noirq resume fixes this
issue.
CANFD2.0 core uses BRAM for storing acceptance filter ID(AFID) and MASK
(AFMASK)registers. So by default AFID and AFMASK registers contain random
data. Due to random data, we are not able to receive all CAN ids.
Initializing AFID and AFMASK registers with Zero before enabling
acceptance filter to receive all packets irrespective of ID and Mask.
Currently the reserved region for ISA is allocated with no
permissions. If a dma domain is being used, mapping this region will
fail. Set the permissions to DMA_PTE_READ|DMA_PTE_WRITE.
Cc: Joerg Roedel <jroedel@suse.de> Cc: Lu Baolu <baolu.lu@linux.intel.com> Cc: iommu@lists.linux-foundation.org Cc: stable@vger.kernel.org # v5.3+ Fixes: d850c2ee5fe2 ("iommu/vt-d: Expose ISA direct mapping region via iommu_get_resv_regions") Signed-off-by: Jerry Snitselaar <jsnitsel@redhat.com> Acked-by: Lu Baolu <baolu.lu@linux.intel.com> Signed-off-by: Joerg Roedel <jroedel@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit d850c2ee5fe2 ("iommu/vt-d: Expose ISA direct mapping region via
iommu_get_resv_regions") created a direct-mapped reserved memory region
in order to replace the static identity mapping of the ISA address
space, where the latter was then removed in commit df4f3c603aeb
("iommu/vt-d: Remove static identity map code"). According to the
history of this code and the Kconfig option surrounding it, this direct
mapping exists for the benefit of legacy ISA drivers that are not
compatible with the DMA API.
In conjuntion with commit 9b77e5c79840 ("vfio/type1: check dma map
request is within a valid iova range") this change introduced a
regression where the vfio IOMMU backend enforces reserved memory regions
per IOMMU group, preventing userspace from creating IOMMU mappings
conflicting with prescribed reserved regions. A necessary prerequisite
for the vfio change was the introduction of "relaxable" direct mappings
introduced by commit adfd37382090 ("iommu: Introduce
IOMMU_RESV_DIRECT_RELAXABLE reserved memory regions"). These relaxable
direct mappings provide the same identity mapping support in the default
domain, but also indicate that the reservation is software imposed and
may be relaxed under some conditions, such as device assignment.
Convert the ISA bridge direct-mapped reserved region to relaxable to
reflect that the restriction is self imposed and need not be enforced
by drivers such as vfio.
Fixes: 1c5c59fbad20 ("iommu/vt-d: Differentiate relaxable and non relaxable RMRRs") Cc: stable@vger.kernel.org # v5.3+ Link: https://lore.kernel.org/linux-iommu/20191211082304.2d4fab45@x1.home Reported-by: cprt <cprt@protonmail.com> Tested-by: cprt <cprt@protonmail.com> Signed-off-by: Alex Williamson <alex.williamson@redhat.com> Acked-by: Lu Baolu <baolu.lu@linux.intel.com> Reviewed-by: Eric Auger <eric.auger@redhat.com> Tested-by: Jerry Snitselaar <jsnitsel@redhat.com> Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com> Signed-off-by: Joerg Roedel <jroedel@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the default DMA domain of a group doesn't fit a device, it
will still sit in the group but use a private identity domain.
When map/unmap/iova_to_phys come through iommu API, the driver
should still serve them, otherwise, other devices in the same
group will be impacted. Since identity domain has been mapped
with the whole available memory space and RMRRs, we don't need
to worry about the impact on it.
Link: https://www.spinics.net/lists/iommu/msg40416.html Cc: Jerry Snitselaar <jsnitsel@redhat.com> Reported-by: Jerry Snitselaar <jsnitsel@redhat.com> Fixes: 942067f1b6b97 ("iommu/vt-d: Identify default domains replaced with private") Cc: stable@vger.kernel.org # v5.3+ Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com> Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com> Tested-by: Jerry Snitselaar <jsnitsel@redhat.com> Signed-off-by: Joerg Roedel <jroedel@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
iommu_group_create_direct_mappings uses group->default_domain, but
right after it is called, request_default_domain_for_dev calls
iommu_domain_free for the default domain, and sets the group default
domain to a different domain. Move the
iommu_group_create_direct_mappings call to after the group default
domain is set, so the direct mappings get associated with that domain.
Cc: Joerg Roedel <jroedel@suse.de> Cc: Lu Baolu <baolu.lu@linux.intel.com> Cc: iommu@lists.linux-foundation.org Cc: stable@vger.kernel.org Fixes: 7423e01741dd ("iommu: Add API to request DMA domain for device") Signed-off-by: Jerry Snitselaar <jsnitsel@redhat.com> Reviewed-by: Lu Baolu <baolu.lu@linux.intel.com> Signed-off-by: Joerg Roedel <jroedel@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case the new region gets merged into another one, the nr list node is
freed. Checking its type while completing the merge algorithm leads to
a use-after-free. Use new->type instead.
Fixes: 4dbd258ff63e ("iommu: Revisit iommu_insert_resv_region() implementation") Signed-off-by: Eric Auger <eric.auger@redhat.com> Reported-by: Qian Cai <cai@lca.pw> Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com> Cc: Stable <stable@vger.kernel.org> #v5.3+ Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When an application sends TPM commands in NONBLOCKING mode
the driver holds chip->tpm_mutex returning from write(),
which triggers: "WARNING: lock held when returning to user space".
To fix this issue the driver needs to release the mutex before
returning and acquire it again in tpm_dev_async_work() before
sending the command.
Cc: stable@vger.kernel.org Fixes: 9e1b74a63f776 (tpm: add support for nonblocking operation) Reported-by: Jeffrin Jose T <jeffrin@rajagiritech.edu.in> Tested-by: Jeffrin Jose T <jeffrin@rajagiritech.edu.in> Signed-off-by: Tadeusz Struk <tadeusz.struk@intel.com> Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of repeatedly calling tpm_chip_start/tpm_chip_stop when
issuing commands to the tpm during initialization, just reserve the
chip after wait_startup, and release it when we are ready to call
tpm_chip_register.
Cc: Christian Bundy <christianbundy@fraction.io> Cc: Dan Williams <dan.j.williams@intel.com> Cc: Peter Huewe <peterhuewe@gmx.de> Cc: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Cc: Jason Gunthorpe <jgg@ziepe.ca> Cc: Stefan Berger <stefanb@linux.vnet.ibm.com> Cc: stable@vger.kernel.org Cc: linux-integrity@vger.kernel.org Fixes: a3fbfae82b4c ("tpm: take TPM chip power gating out of tpm_transmit()") Fixes: 5b359c7c4372 ("tpm_tis_core: Turn on the TPM before probing IRQ's") Suggested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Signed-off-by: Jerry Snitselaar <jsnitsel@redhat.com> Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
there is a chance that always get response CRC error after HS200 tuning,
the reason is that need set CMD_TA to 2. this modification is only for
MT8173.
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com> Tested-by: Hsin-Yi Wang <hsinyi@chromium.org> Cc: stable@vger.kernel.org Fixes: 1ede5cb88a29 ("mmc: mediatek: Use data tune for CMD line tune") Link: https://lore.kernel.org/r/20191204071958.18553-1-chaotian.jing@mediatek.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit aims to treat SD High speed and SDR25 as the same while
setting UHS Timings in HOST_CONTROL2 which leads to failures with some
SD cards in AM65x. Revert this commit.
The issue this commit was trying to fix can be implemented in a platform
specific callback instead of common sdhci code.
Cc: <stable@vger.kernel.org> Signed-off-by: Faiz Abbas <faiz_abbas@ti.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Link: https://lore.kernel.org/r/20191128110422.25917-1-faiz_abbas@ti.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, scrub_missing_raid56_worker() puts and potentially frees
sblock (which embeds the work item) and then submits a bio through
scrub_wr_submit(). This is another potential instance of the bug in
"btrfs: don't prematurely free work in run_ordered_work()". Fix it by
dropping the reference after we submit the bio.
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Omar Sandoval <osandov@fb.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently, reada_start_machine_worker() frees the reada_machine_work and
then calls __reada_start_machine() to do readahead. This is another
potential instance of the bug in "btrfs: don't prematurely free work in
run_ordered_work()".
There _might_ already be a deadlock here: reada_start_machine_worker()
can depend on itself through stacked filesystems (__read_start_machine()
-> reada_start_machine_dev() -> reada_tree_block_flagged() ->
read_extent_buffer_pages() -> submit_one_bio() ->
btree_submit_bio_hook() -> btrfs_map_bio() -> submit_stripe_bio() ->
submit_bio() onto a loop device can trigger readahead on the lower
filesystem).
Either way, let's fix it by freeing the work at the end.
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Omar Sandoval <osandov@fb.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit 3c1d3f097972 ("MIPS: futex: Emit Loongson3 sync workarounds
within asm") inadvertently removed the newlines following
__WEAK_LLSC_MB, which causes build failures for configurations in which
__WEAK_LLSC_MB expands to a sync instruction:
{standard input}: Assembler messages:
{standard input}:9346: Error: symbol `sync3' is already defined
{standard input}:9380: Error: symbol `sync3' is already defined
...
Fix this by restoring the newlines to separate the sync instruction from
anything following it (such as the 3: label), preventing inadvertent
concatenation.
Signed-off-by: Paul Burton <paul.burton@mips.com> Fixes: 3c1d3f097972 ("MIPS: futex: Emit Loongson3 sync workarounds within asm") Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit 6570bc79c0df ("net: core: use listified Rx for GRO_NORMAL in
napi_gro_receive()") has applied batched GRO_NORMAL packets processing
to all napi_gro_receive() users, including mac80211-based drivers.
However, this change has led to a regression in iwlwifi driver [1][2] as
it is required for NAPI users to call napi_complete_done() or
napi_complete() and the end of every polling iteration, whilst iwlwifi
doesn't use NAPI scheduling at all and just calls napi_gro_flush().
In that particular case, packets which have not been already flushed
from napi->rx_list stall in it until at least next Rx cycle.
Fix this by adding a manual flushing of the list to iwlwifi driver right
before napi_gro_flush() call to mimic napi_complete() logics.
I prefer to open-code gro_normal_list() rather than exporting it for 2
reasons:
* to prevent from using it and napi_gro_flush() in any new drivers,
as it is the *really* bad way to use NAPI that should be avoided;
* to keep gro_normal_list() static and don't lose any CC optimizations.
I also don't add the "Fixes:" tag as the mentioned commit was only a
trigger that only exposed an improper usage of NAPI in this particular
driver.
Signed-off-by: Alexander Lobakin <alobakin@dlink.ru> Acked-by: Luca Coelho <luciano.coelho@intel.com> Reported-by: Nicholas Johnson <nicholas.johnson-opensource@outlook.com.au> Tested-by: Nicholas Johnson <nicholas.johnson-opensource@outlook.com.au> Reviewed-by: Edward Cree <ecree@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fix multiple calls to init_completion for device completion
structures. Instead, initialize them during device probe and
reinitialize them later as needed.
Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
With latest llvm (trunk https://github.com/llvm/llvm-project),
test_progs, which has +alu32 enabled, failed for strobemeta.o.
The verifier output looks like below with edit to replace large
decimal numbers with hex ones.
193: (85) call bpf_probe_read_user_str#114
R0=inv(id=0)
194: (26) if w0 > 0x1 goto pc+4
R0_w=inv(id=0,umax_value=0xffffffff00000001)
195: (6b) *(u16 *)(r7 +80) = r0
196: (bc) w6 = w0
R6_w=inv(id=0,umax_value=0xffffffff,var_off=(0x0; 0xffffffff))
197: (67) r6 <<= 32
R6_w=inv(id=0,smax_value=0x7fffffff00000000,umax_value=0xffffffff00000000,
var_off=(0x0; 0xffffffff00000000))
198: (77) r6 >>= 32
R6=inv(id=0,umax_value=0xffffffff,var_off=(0x0; 0xffffffff))
...
201: (79) r8 = *(u64 *)(r10 -416)
R8_w=map_value(id=0,off=40,ks=4,vs=13872,imm=0)
202: (0f) r8 += r6
R8_w=map_value(id=0,off=40,ks=4,vs=13872,umax_value=0xffffffff,var_off=(0x0; 0xffffffff))
203: (07) r8 += 9696
R8_w=map_value(id=0,off=9736,ks=4,vs=13872,umax_value=0xffffffff,var_off=(0x0; 0xffffffff))
...
255: (bf) r1 = r8
R1_w=map_value(id=0,off=9736,ks=4,vs=13872,umax_value=0xffffffff,var_off=(0x0; 0xffffffff))
...
257: (85) call bpf_probe_read_user_str#114
R1 unbounded memory access, make sure to bounds check any array access into a map
The value range for register r6 at insn 198 should be really just 0/1.
The umax_value=0xffffffff caused later verification failure.
After jmp instructions, the current verifier already tried to use just
obtained information to get better register range. The current mechanism is
for 64bit register only. This patch implemented to tighten the range
for 32bit sub-registers after jmp32 instructions.
With the patch, we have the below range ranges for the
above code sequence:
193: (85) call bpf_probe_read_user_str#114
R0=inv(id=0)
194: (26) if w0 > 0x1 goto pc+4
R0_w=inv(id=0,smax_value=0x7fffffff00000001,umax_value=0xffffffff00000001,
var_off=(0x0; 0xffffffff00000001))
195: (6b) *(u16 *)(r7 +80) = r0
196: (bc) w6 = w0
R6_w=inv(id=0,umax_value=0xffffffff,var_off=(0x0; 0x1))
197: (67) r6 <<= 32
R6_w=inv(id=0,umax_value=0x100000000,var_off=(0x0; 0x100000000))
198: (77) r6 >>= 32
R6=inv(id=0,umax_value=1,var_off=(0x0; 0x1))
...
201: (79) r8 = *(u64 *)(r10 -416)
R8_w=map_value(id=0,off=40,ks=4,vs=13872,imm=0)
202: (0f) r8 += r6
R8_w=map_value(id=0,off=40,ks=4,vs=13872,umax_value=1,var_off=(0x0; 0x1))
203: (07) r8 += 9696
R8_w=map_value(id=0,off=9736,ks=4,vs=13872,umax_value=1,var_off=(0x0; 0x1))
...
255: (bf) r1 = r8
R1_w=map_value(id=0,off=9736,ks=4,vs=13872,umax_value=1,var_off=(0x0; 0x1))
...
257: (85) call bpf_probe_read_user_str#114
...
At insn 194, the register R0 has better var_off.mask and smax_value.
Especially, the var_off.mask ensures later lshift and rshift
maintains proper value range.
Due to recent advances in the firmware for Broadcom's gen p5 series of
adaptors the driver code to report hardware counters has been broken
w.r.t. roce devices.
The new firmware command expects dma length to be specified during stat
dma buffer allocation.
Building selftests with 'make TARGETS=bpf kselftest' was fixed in commit 55d554f5d140 ("tools: bpf: Use !building_out_of_srctree to determine
srctree"). However, by updating $(srctree) in tools/bpf/Makefile for
in-tree builds only, we leave out the case where we pass an output
directory to build BPF tools, but $(srctree) is not set. This
typically happens for:
$ make -s tools/bpf O=/tmp/foo
Makefile:40: /tools/build/Makefile.feature: No such file or directory
Fix it by updating $(srctree) in the Makefile not only for out-of-tree
builds, but also if $(srctree) is empty.
Detected with test_bpftool_build.sh.
Fixes: 55d554f5d140 ("tools: bpf: Use !building_out_of_srctree to determine srctree") Signed-off-by: Quentin Monnet <quentin.monnet@netronome.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com> Link: https://lore.kernel.org/bpf/20191119105626.21453-1-quentin.monnet@netronome.com Signed-off-by: Sasha Levin <sashal@kernel.org>
When a phydev is created, the speed and duplex are set to zero and
-1 respectively, rather than using the predefined SPEED_UNKNOWN and
DUPLEX_UNKNOWN constants.
There is a window at initialisation time where we may report link
down using the 0/-1 values. Tidy this up and use the predefined
constants, so debug doesn't complain with:
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently there can be a case where a DCB map is applied and there are
more interrupt vectors (vsi->num_q_vectors) than Rx queues (vsi->num_rxq)
and Tx queues (vsi->num_txq). If we try to set coalesce settings in this
case it will report a false failure. Fix this by checking if vector index
is valid with respect to the number of Tx and Rx queues configured.
Signed-off-by: Brett Creeley <brett.creeley@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
It is wrong to set PF disable state flag for all VFs when freeing VF
resources - Instead, we should set VF disable state flag for each VF with
its resources being returned to the device. Right now, all VF opcodes,
mailbox communication to clear its resources as well fails - since we
already indicate that PF is in disable state, with all VFs not active. In
addition, we don't need to notify VF that PF is intending to reset it, if
it is already in disabled state.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The INTERRUPT_CNTL2 register expects a valid DMA address, but is
currently set with a GPU MC address. This can cause problems on
systems that detect the resulting DMA read from an invalid address
(found on a Power8 guest).
Instead, use the DMA address of the dummy page because it will always
be safe.
Fixes: 27ae10641e9c ("drm/amdgpu: add interupt handler implementation for si v3") Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
With CONFIG_MIPS_VA_BITS_48=y the build fails miserably:
CC arch/mips/kernel/asm-offsets.s
In file included from arch/mips/include/asm/pgtable.h:644,
from include/linux/mm.h:99,
from arch/mips/kernel/asm-offsets.c:15:
include/asm-generic/pgtable.h:16:2: error: #error CONFIG_PGTABLE_LEVELS is not consistent with __PAGETABLE_{P4D,PUD,PMD}_FOLDED
#error CONFIG_PGTABLE_LEVELS is not consistent with __PAGETABLE_{P4D,PUD,PMD}_FOLDED
^~~~~
include/asm-generic/pgtable.h:390:28: error: unknown type name 'p4d_t'; did you mean 'pmd_t'?
static inline int p4d_same(p4d_t p4d_a, p4d_t p4d_b)
^~~~~
pmd_t
This happens because when CONFIG_MIPS_VA_BITS_48 enables 4th level of the
page tables, but neither pgtable-nop4d.h nor 5level-fixup.h are included to
cope with the 5th level.
Replace #ifdef conditions around includes of the pgtable-nop{m,u}d.h with
explicit CONFIG_PGTABLE_LEVELS and add include of 5level-fixup.h for the
case when CONFIG_PGTABLE_LEVELS==4
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com> Signed-off-by: Paul Burton <paulburton@kernel.org> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: James Hogan <jhogan@kernel.org> Cc: linux-mips@vger.kernel.org Cc: linux-kernel@vger.kernel.org Cc: linux-mm@kvack.org Cc: Mike Rapoport <rppt@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In the vmx crypto Makefile we assign to a variable called TARGET and
pass that to the aesp8-ppc.pl and ghashp8-ppc.pl scripts.
The variable is meant to describe what flavour of powerpc we're
building for, eg. either 32 or 64-bit, and big or little endian.
Unfortunately TARGET is a fairly common name for a make variable, and
if it happens that TARGET is specified as a command line parameter to
make, the value specified on the command line will override our value.
In particular this can happen if the kernel Makefile is driven by an
external Makefile that uses TARGET for something.
This leads to weird build failures, eg:
nonsense at /build/linux/drivers/crypto/vmx/ghashp8-ppc.pl line 45.
/linux/drivers/crypto/vmx/Makefile:20: recipe for target 'drivers/crypto/vmx/ghashp8-ppc.S' failed
Which shows that we passed an empty value for $(TARGET) to the perl
script, confirmed with make V=1:
We can avoid this confusion by using override, to tell make that we
don't want anything to override our variable, even a value specified
on the command line. We can also use a less common name, given the
script calls it "flavour", let's use that.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit 7b6ddeaf27ec ("mac80211: use QoS NDP for AP probing")
let STAs send QoS Null frames as PS triggers if the AP was
a QoS STA. However, the mac80211 PS stack relies on an
interface flag IEEE80211_STA_NULLFUNC_ACKED for
determining trigger frame ACK, which was not being set for
acked non-QoS Null frames. The effect is an inability to
trigger hardware sleep via IEEE80211_CONF_PS since the QoS
Null frame was seemingly never acked.
This bug only applies to drivers which set both
IEEE80211_HW_REPORTS_TX_ACK_STATUS and
IEEE80211_HW_PS_NULLFUNC_STACK.
Detect the acked QoS Null frame to restore STA power save.
Fixes: 7b6ddeaf27ec ("mac80211: use QoS NDP for AP probing") Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com> Link: https://lore.kernel.org/r/20191119053538.25979-4-thomas@adapt-ip.com Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
If you try to compile this driver on a 64-bit platform then you
will get warnings because it mixes size_t with unsigned int which
only works on 32-bit.
This patch fixes all of the warnings on sun4i-ss-hash.c. Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
If you try to compile this driver on a 64-bit platform then you
will get warnings because it mixes size_t with unsigned int which
only works on 32-bit.
This patch fixes all of the warnings.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Acked-by: Corentin Labbe <clabbe.montjoie@gmail.com> Tested-by: Corentin Labbe <clabbe.montjoie@gmail.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
Linux-next commit titled "perf/core: Optimize perf_init_event()"
changed the semantics of PMU device driver registration.
It was done to speed up the lookup/handling of PMU device driver
specific events. It also enforces that only one PMU device
driver will be registered of type PERF_EVENT_RAW.
This change added these line in function perf_pmu_register():
...
+ ret = idr_alloc(&pmu_idr, pmu, max, 0, GFP_KERNEL);
+ if (ret < 0)
goto free_pdc;
+
+ WARN_ON(type >= 0 && ret != type);
The warn_on generates a message. We have 3 PMU device drivers,
each registered as type PERF_TYPE_RAW.
The cf_diag device driver (arch/s390/kernel/perf_cpumf_cf_diag.c)
always hits the WARN_ON because it is the second PMU device driver
(after sampling device driver arch/s390/kernel/perf_cpumf_sf.c)
which is registered as type 4 (PERF_TYPE_RAW).
So when the sampling device driver is registered, ret has value 4.
When cf_diag device driver is registered with type 4,
ret has value of 5 and WARN_ON fires.
Adjust the PMU device drivers for s390 to support the new
semantics required by perf_pmu_register().
Clean CPSW ALE on init and intf restart (up/down) to avoid reading obsolete
or garbage entries from ALE table.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
This reverts commit 957ce0c6b8a1f (ASoC: soc-pcm: check symmetry after
hw_params).
That commit cause soc_pcm_params_symmetry can't take effect.
cpu_dai->rate, cpu_dai->channels and cpu_dai->sample_bits
are updated in the middle of soc_pcm_hw_params, so move
soc_pcm_params_symmetry to the end of soc_pcm_hw_params is
not a good solution, for judgement of symmetry in the function
is always true.
FIXME:
According to the comments of that commit, I think the case
described in the commit should disable symmetric_rates
in Back-End, rather than changing the position of
soc_pcm_params_symmetry.
When hardware reports RX buffer errors, the latest 57500 chips do not
require reset. The packet is discarded by the hardware and the
ring will continue to operate.
Also, add an rx_buf_errors counter for this type of error. It can help
the user to identify if the aggregation ring is too small.
Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently if the kernel is built with CONFIG_TRACE_IRQFLAGS and KASAN
and used as crash kernel it crashes itself due to
trace_hardirqs_off/trace_hardirqs_on being called with DAT off. This
happens because trace_hardirqs_off/trace_hardirqs_on are instrumented and
kasan code tries to perform access to shadow memory to validate memory
accesses. Kasan shadow memory is populated with vmemmap, so all accesses
require DAT on.
memcpy_real could be called with DAT on or off (with kasan enabled DAT
is set even before early code is executed).
Make sure that trace_hardirqs_off/trace_hardirqs_on are called with DAT
on and only actual __memcpy_real is called with DAT off.
Also annotate __memcpy_real and _memcpy_real with __no_sanitize_address
to avoid further problems due to switching DAT off.
Fix die_walk_lines() to list the function entry line correctly. Since
the dwarf_entrypc() does not return the entry pc if the DIE has only
range attribute, __die_walk_funclines() fails to list the declaration
line (entry line) in that case.
To solve this issue, this introduces die_entrypc() which correctly
returns the entry PC (the first address range) even if the DIE has only
range attribute. With this fix die_walk_lines() shows the function entry
line is able to probe correctly.
Fixes: 4cc9cec636e7 ("perf probe: Introduce lines walker interface") Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Namhyung Kim <namhyung@kernel.org> Link: http://lore.kernel.org/lkml/157190837419.1859.4619125803596816752.stgit@devnote2 Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Thomas Backlund <tmb@mageia.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Avoid termination of trace loading in case the last record in the
decompressed buffer partly resides in the following mmaped
PERF_RECORD_COMPRESSED record.
In this case NULL value returned by fetch_mmaped_event() means to
proceed to the next mmaped record then decompress it and load compressed
events.
The issue can be reproduced like this:
$ perf record -z -- some_long_running_workload
$ perf report --stdio -vv
decomp (B): 44519 to 163000
decomp (B): 48119 to 174800
decomp (B): 65527 to 131072
fetch_mmaped_event: head=0x1ffe0 event->header_size=0x28, mmap_size=0x20000: fuzzed perf.data?
Error:
failed to process sample
...
Testing:
71: Zstd perf.data compression/decompression : Ok
$ tools/perf/perf report -vv --stdio
decomp (B): 59593 to 262160
decomp (B): 4438 to 16512
decomp (B): 285 to 880
Looking at the vmlinux_path (8 entries long)
Using vmlinux for symbols
decomp (B): 57474 to 261248
prefetch_event: head=0x3fc78 event->header_size=0x28, mmap_size=0x3fc80: fuzzed or compressed perf.data?
decomp (B): 25 to 32
decomp (B): 52 to 120
...
Fixes: 57fc032ad643 ("perf session: Avoid infinite loop when seeing invalid header.size") Link: https://marc.info/?l=linux-kernel&m=156580812427554&w=2 Co-developed-by: Jiri Olsa <jolsa@kernel.org> Acked-by: Jiri Olsa <jolsa@kernel.org> Signed-off-by: Alexey Budankov <alexey.budankov@linux.intel.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Andi Kleen <ak@linux.intel.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Link: http://lore.kernel.org/lkml/cf782c34-f3f8-2f9f-d6ab-145cee0d5322@linux.intel.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
This fixes a minor WARNING in the cfg80211:
[ 130.658034] ------------[ cut here ]------------
[ 130.662805] WARNING: CPU: 1 PID: 610 at net/wireless/core.c:954 wiphy_unregister+0xb4/0x198 [cfg80211]
Signed-off-by: Rafał Miłecki <rafal@milecki.pl> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Drivers use different fields to report the number of channels, so take
the maximum of all data channels (rx, tx, combined) when determining the
size of the xsk map. The current code used only 'combined' which was set
to 0 in some drivers e.g. mlx4.
Tested: compiled and run xdpsock -q 3 -r -S on mlx4
Signed-off-by: Luigi Rizzo <lrizzo@google.com> Signed-off-by: Alexei Starovoitov <ast@kernel.org> Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com> Acked-by: Magnus Karlsson <magnus.karlsson@intel.com> Link: https://lore.kernel.org/bpf/20191119001951.92930-1-lrizzo@google.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Add to the opcode map the following instructions:
cldemote
tpause
umonitor
umwait
movdiri
movdir64b
enqcmd
enqcmds
encls
enclu
enclv
pconfig
wbnoinvd
For information about the instructions, refer Intel SDM May 2019
(325462-070US) and Intel Architecture Instruction Set Extensions
May 2019 (319433-037).
The instruction decoding can be tested using the perf tools'
"x86 instruction decoder - new instructions" test as folllows:
When the Acer Switch 10 SW5-012 quirk was added we did not have
jack-detection support yet; and the builtin microphone selection of
the original quirk is wrong too.
Fix the microphone-input quirk and add jack-detection info so that the
internal-microphone and headphone/set jack on the Switch 10 work properly.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Link: https://lore.kernel.org/r/20191119145138.59162-1-hdegoede@redhat.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Some firmware images contain a comma, such as:
EXTRA_FIRMWARE "brcm/brcmfmac4334-sdio.samsung,gt-s7710.txt"
as Broadcom firmware simply tags the device tree compatible
string at the end of the firmware parameter file. And the
compatible string contains a comma.
We currently match clause 45 PHYs using any ID read from a MMD marked
as present in the "Devices in package" registers 5 and 6. However,
this is incorrect. 45.2 says:
"The definition of the term package is vendor specific and could be
a chip, module, or other similar entity."
so a package could be more or less than the whole PHY - a PHY could be
made up of several modules instantiated onto a single chip such as the
Marvell 88x3310, or some of the MMDs could be disabled according to
chip configuration, such as the Broadcom 84881.
In the case of Broadcom 84881, the "Devices in package" registers
contain 0xc000009b, meaning that there is a PHYXS present in the
package, but all registers in MMD 4 return 0xffff. This leads to our
matching code incorrectly binding this PHY to one of our generic PHY
drivers.
This patch changes the way we determine whether to attempt to match a
MMD identifier, or use it to request a module - if the identifier is
all-ones, then we skip over it. When reading the identifiers, we
initialise phydev->c45_ids.device_ids to all-ones, only reading the
device ID if the "Devices in package" registers indicates we should.
This avoids the generic drivers incorrectly matching on a PHY ID of
0xffffffff.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
For NVM params that are not supported in the current NVM
configuration, return the error as -EOPNOTSUPP.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The main reason for verification failure is due to partial spills at
r10 - 68 for induction variable "i".
Current verifier only handles spills with 8-byte values. The above 4-byte
value spill to stack is treated to STACK_MISC and its content is not
saved. For the above example:
To resolve this issue, verifier needs to be extended to track sub-registers
in spilling, or llvm needs to enhanced to prevent sub-register spilling
in register allocation phase. The former will increase verifier complexity
and the latter will need some llvm "hacking".
Let us workaround this issue by declaring the induction variable as "long"
type so spilling will happen at non sub-register level. We can revisit this
later if sub-register spilling causes similar or other verification issues.
Signed-off-by: Yonghong Song <yhs@fb.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Andrii Nakryiko <andriin@fb.com> Link: https://lore.kernel.org/bpf/20191117214036.1309510-1-yhs@fb.com Signed-off-by: Sasha Levin <sashal@kernel.org>
When run_kselftests.sh is run, it hangs after test_tc_tunnel.sh. The reason
is test_tc_tunnel.sh ensures the server ('nc -l') is run all the time,
starting it again every time it is expected to terminate. The exception is
the final client_connect: the server is not started anymore, which ensures
no process is kept running after the test is finished.
For a sit test, though, the script is terminated prematurely without the
final client_connect and the 'nc' process keeps running. This in turn causes
the run_one function in kselftest/runner.sh to hang forever, waiting for the
runaway process to finish.
Ensure a remaining server is terminated on cleanup.
5e6c3c7b1ec2 ("perf/aux: Fix tracking of auxiliary trace buffer allocation")
tried to guess the correct combination of arithmetic operations that would
undo the AUX buffer's mlock accounting, and failed, leaking the bottom part
when an allocation needs to be charged partially to both user->locked_vm
and mm->pinned_vm, eventually leaving the user with no locked bonus:
$ perf record -e intel_pt//u -m1,128 uname
[ perf record: Woken up 1 times to write data ]
[ perf record: Captured and wrote 0.061 MB perf.data ]
$ perf record -e intel_pt//u -m1,128 uname
Permission error mapping pages.
Consider increasing /proc/sys/kernel/perf_event_mlock_kb,
or try again with a smaller value of -m/--mmap_pages.
(current value: 1,128)
Fix this by subtracting both locked and pinned counts when AUX buffer is
unmapped.
Reported-by: Thomas Richter <tmricht@linux.ibm.com> Tested-by: Thomas Richter <tmricht@linux.ibm.com> Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com> Acked-by: Peter Zijlstra <peterz@infradead.org> Cc: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Stephane Eranian <eranian@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Vince Weaver <vincent.weaver@maine.edu> Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Some uclamp helpers had their return type changed from 'unsigned int' to
'enum uclamp_id' by commit
0413d7f33e60 ("sched/uclamp: Always use 'enum uclamp_id' for clamp_id values")
but it happens that some do return a value in the [0, SCHED_CAPACITY_SCALE]
range, which should really be unsigned int. The affected helpers are
uclamp_none(), uclamp_rq_max_value() and uclamp_eff_value(). Fix those up.
Note that this doesn't lead to any obj diff using a relatively recent
aarch64 compiler (8.3-2019.03). The current code of e.g. uclamp_eff_value()
properly returns an 11 bit value (bits_per(1024)) and doesn't seem to do
anything funny. I'm still marking this as fixing the above commit to be on
the safe side.
We hit the following very strange deadlock on a system with Btrfs on a
loop device backed by another Btrfs filesystem:
1. The top (loop device) filesystem queues an async_cow work item from
cow_file_range_async(). We'll call this work X.
2. Worker thread A starts work X (normal_work_helper()).
3. Worker thread A executes the ordered work for the top filesystem
(run_ordered_work()).
4. Worker thread A finishes the ordered work for work X and frees X
(work->ordered_free()).
5. Worker thread A executes another ordered work and gets blocked on I/O
to the bottom filesystem (still in run_ordered_work()).
6. Meanwhile, the bottom filesystem allocates and queues an async_cow
work item which happens to be the recently-freed X.
7. The workqueue code sees that X is already being executed by worker
thread A, so it schedules X to be executed _after_ worker thread A
finishes (see the find_worker_executing_work() call in
process_one_work()).
Now, the top filesystem is waiting for I/O on the bottom filesystem, but
the bottom filesystem is waiting for the top filesystem to finish, so we
deadlock.
This happens because we are breaking the workqueue assumption that a
work item cannot be recycled while it still depends on other work. Fix
it by waiting to free the work item until we are done with all of the
related ordered work.
P.S.:
One might ask why the workqueue code doesn't try to detect a recycled
work item. It actually does try by checking whether the work item has
the same work function (find_worker_executing_work()), but in our case
the function is the same. This is the only key that the workqueue code
has available to compare, short of adding an additional, layer-violating
"custom key". Considering that we're the only ones that have ever hit
this, we should just play by the rules.
Unfortunately, we haven't been able to create a minimal reproducer other
than our full container setup using a compress-force=zstd filesystem on
top of another compress-force=zstd filesystem.
Suggested-by: Tejun Heo <tj@kernel.org> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Omar Sandoval <osandov@fb.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently, end_workqueue_fn() frees the end_io_wq entry (which embeds
the work item) and then calls bio_endio(). This is another potential
instance of the bug in "btrfs: don't prematurely free work in
run_ordered_work()".
In particular, the endio call may depend on other work items. For
example, btrfs_end_dio_bio() can call btrfs_subio_endio_read() ->
__btrfs_correct_data_nocsum() -> dio_read_error() ->
submit_dio_repair_bio(), which submits a bio that is also completed
through a end_workqueue_fn() work item. However,
__btrfs_correct_data_nocsum() waits for the newly submitted bio to
complete, thus it depends on another work item.
This example currently usually works because we use different workqueue
helper functions for BTRFS_WQ_ENDIO_DATA and BTRFS_WQ_ENDIO_DIO_REPAIR.
However, it may deadlock with stacked filesystems and is fragile
overall. The proper fix is to free the work item at the very end of the
work function, so let's do that.
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Omar Sandoval <osandov@fb.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Isolated initially to renesas_sdhi_internal_dmac [1], Ulf suggested
adding MMC_CAP_ERASE to the TMIO mmc core:
On Fri, Nov 15, 2019 at 10:27:25AM +0100, Ulf Hansson wrote:
-- snip --
This test and due to the discussions with Wolfram and you in this
thread, I would actually suggest that you enable MMC_CAP_ERASE for all
tmio variants, rather than just for this particular one.
In other words, set the cap in tmio_mmc_host_probe() should be fine,
as it seems none of the tmio variants supports HW busy detection at
this point.
-- snip --
Testing on R-Car H3ULCB-KF doesn't reveal any issues (v5.4-rc7):
root@rcar-gen3:~# lsblk
NAME MAJ:MIN RM SIZE RO TYPE MOUNTPOINT
mmcblk0 179:0 0 59.2G 0 disk <--- eMMC
mmcblk0boot0 179:8 0 4M 1 disk
mmcblk0boot1 179:16 0 4M 1 disk
mmcblk1 179:24 0 30G 0 disk <--- SD card
root@rcar-gen3:~# time blkdiscard /dev/mmcblk0
real 0m8.659s
user 0m0.001s
sys 0m1.920s
root@rcar-gen3:~# time blkdiscard /dev/mmcblk1
real 0m1.176s
user 0m0.001s
sys 0m0.124s
Intel Ice Lake has two xHCI controllers one on PCH and the other as part
of the CPU itself. The latter is also part of the so called Type C
Subsystem (TCSS) sharing ACPI power resources with the PCIe root ports
and the Thunderbolt controllers. In order to put the whole TCSS block
into D3cold the xHCI needs to be runtime suspended as well when idle.
For this reason allow runtime PM as default for Ice Lake TCSS xHCI
controller.
There is a race in the TUN driver between napi_busy_loop and
napi_gro_frags. This commit resolves the race by adding the NAPI struct
via netif_tx_napi_add, instead of netif_napi_add, which disables polling
for the NAPI struct.
KCSAN reported:
BUG: KCSAN: data-race in gro_normal_list.part.0 / napi_busy_loop
Reported by Kernel Concurrency Sanitizer on:
CPU: 1 PID: 11168 Comm: syz-executor.0 Not tainted 5.4.0-rc6+ #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Fixes: 943170998b20 ("tun: enable NAPI for TUN/TAP driver") Signed-off-by: Petar Penkov <ppenkov@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The current code assumes that the power is turned off in
SND_SOC_BIAS_OFF. If there are no actual regulator the codec isn't
turned off and the registers are not reset to their default values but
the regcache is still marked as dirty. Thus a value might not be written
to the hardware if it is set to the default value. Do a software reset
before turning off the power to make sure the registers are always reset
to their default states.
Signed-off-by: Michael Walle <michael@walle.cc> Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com> Link: https://lore.kernel.org/r/20191112223629.21867-1-michael@walle.cc Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / thirdparty / kernel / stable.git / log
