UDC driver should not touch gadget's driver internals, especially it
should not reset driver->bus. This wasn't harmful so far, but since
commit fc274c1e9973 ("USB: gadget: Add a new bus for gadgets") gadget
subsystem got it's own bus and messing with ->bus triggers the
following NULL pointer dereference:
dwc2 12480000.hsotg: bound driver g_ether
8<--- cut here ---
Unable to handle kernel NULL pointer dereference at virtual address 00000000
[00000000] *pgd=00000000
Internal error: Oops: 5 [#1] SMP ARM
Modules linked in: ...
CPU: 0 PID: 620 Comm: modprobe Not tainted 5.18.0-rc5-next-20220504 #11862
Hardware name: Samsung Exynos (Flattened Device Tree)
PC is at module_add_driver+0x44/0xe8
LR is at sysfs_do_create_link_sd+0x84/0xe0
...
Process modprobe (pid: 620, stack limit = 0x(ptrval))
...
module_add_driver from bus_add_driver+0xf4/0x1e4
bus_add_driver from driver_register+0x78/0x10c
driver_register from usb_gadget_register_driver_owner+0x40/0xb4
usb_gadget_register_driver_owner from do_one_initcall+0x44/0x1e0
do_one_initcall from do_init_module+0x44/0x1c8
do_init_module from load_module+0x19b8/0x1b9c
load_module from sys_finit_module+0xdc/0xfc
sys_finit_module from ret_fast_syscall+0x0/0x54
Exception stack(0xf1771fa8 to 0xf1771ff0)
...
dwc2 12480000.hsotg: new device is high-speed
---[ end trace 0000000000000000 ]---
The documentation for the freeze() method says that it "should quiesce
the device so that it doesn't generate IRQs or DMA". The unspoken
consequence of not doing this is that MSIs aimed at non-boot CPUs may
get fully lost if they're sent during the period where the target CPU is
offline.
The current callbacks for USB HCD do not fully quiesce interrupts,
specifically on XHCI. Change to use the full suspend/resume flow for
freeze/thaw to ensure interrupts are fully quiesced. This fixes issues
where USB devices fail to thaw during hibernation because XHCI misses
its interrupt and cannot recover.
We hold oxu->lock in position (1) of thread 1, and use
del_timer_sync() to wait timer to stop, but timer handler
also need oxu->lock in position (2) of thread 2. As a result,
oxu_bus_suspend() will block forever.
This patch extracts del_timer_sync() from the protection of
spin_lock_irq(), which could let timer handler to obtain
the needed lock.
We hold sport->port.lock in position (1) of thread 1 and
use del_timer_sync() to wait timer to stop, but timer handler
also need sport->port.lock in position (2) of thread 2. As a result,
sa1100_set_termios() will block forever.
This patch moves del_timer_sync() before spin_lock_irqsave()
in order to prevent the deadlock.
We hold ieee->beacon_lock in position (1) of thread 1 and
use del_timer_sync() to wait timer to stop, but timer handler
also need ieee->beacon_lock in position (2) of thread 2.
As a result, rtllib_beacons_stop() will block forever.
This patch extracts del_timer_sync() from the protection of
spin_lock_irqsave(), which could let timer handler to obtain
the needed lock.
We hold ieee->beacon_lock in position (1) of thread 1 and use
del_timer_sync() to wait timer to stop, but timer handler
also need ieee->beacon_lock in position (2) of thread 2.
As a result, ieee80211_beacons_stop() will block forever.
This patch extracts del_timer_sync() from the protection of
spin_lock_irqsave(), which could let timer handler to obtain
the needed lock.
To be sufficiently out of range for the usercopy test to see the lifetime
mismatch, expand the size of the "bad" buffer, which will let it be
beyond current_stack_pointer regardless of stack growth direction.
Paired with the recent addition of stack depth checking under
CONFIG_HARDENED_USERCOPY=y, this will correctly start tripping again.
kstrdup() is also a memory allocation-related function, it returns NULL
when some memory errors happen. So it is better to check the return
value of it so to catch the memory error in time. Besides, there should
have a kfree() to clear up the allocation if we get a failure later in
this function to prevent memory leak.
Gcc-12 correctly warned about this code using a non-NULL pointer as a
truth value:
drivers/gpu/drm/imx/ipuv3-crtc.c: In function ‘ipu_crtc_disable_planes’:
drivers/gpu/drm/imx/ipuv3-crtc.c:72:21: error: the comparison will always evaluate as ‘true’ for the address of ‘plane’ will never be NULL [-Werror=address]
72 | if (&ipu_crtc->plane[1] && plane == &ipu_crtc->plane[1]->base)
| ^
due to the extraneous '&' address-of operator.
Philipp Zabel points out that The mistake had no adverse effect since
the following condition doesn't actually dereference the NULL pointer,
but the intent of the code was obviously to check for it, not to take
the address of the member.
Every iteration of for_each_child_of_node() decrements
the reference count of the previous node.
When break from a for_each_child_of_node() loop,
we need to explicitly call of_node_put() on the child node when
not need anymore.
Add missing of_node_put() to avoid refcount leak.
Fixes: bbd2190ce96d ("Altera TSE: Add main and header file for Altera Ethernet Driver") Signed-off-by: Miaoqian Lin <linmq006@gmail.com> Link: https://lore.kernel.org/r/20220607041144.7553-1-linmq006@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
But was eventually revised more thoroughly:
- restrict the check to the only branch where needed, in an
uncommon GRE path that uses header_ops and calls skb_pull.
- test skb_transport_header, which is set along with csum_start
in skb_partial_csum_set in the normal header_ops datapath.
Turns out skbs can arrive in this branch without the transport
header set, e.g., through BPF redirection.
Revise the check back to check csum_start directly, and only if
CHECKSUM_PARTIAL. Do leave the check in the updated location.
Check field regardless of whether TUNNEL_CSUM is configured.
The current design does not arm the tracer if traces are available before
the tracer string database is fully loaded, leading to an unfunctional tracer.
This fix will rearm the tracer every time the FW triggers tracer event
regardless of the tracer strings database status.
EXPORT_SYMBOL and __init is a bad combination because the .init.text
section is freed up after the initialization. Hence, modules cannot
use symbols annotated __init. The access to a freed symbol may end up
with kernel panic.
modpost used to detect it, but it has been broken for a decade.
Recently, I fixed modpost so it started to warn it again, then this
showed up in linux-next builds.
There are two ways to fix it:
- Remove __init
- Remove EXPORT_SYMBOL
I chose the latter for this case because the caller (net/ipv6/seg6.c)
and the callee (net/ipv6/seg6_hmac.c) belong to the same module.
It seems an internal function call in ipv6.ko.
Fixes: bf355b8d2c30 ("ipv6: sr: add core files for SR HMAC support") Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Masahiro Yamada <masahiroy@kernel.org> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
EXPORT_SYMBOL and __init is a bad combination because the .init.text
section is freed up after the initialization. Hence, modules cannot
use symbols annotated __init. The access to a freed symbol may end up
with kernel panic.
modpost used to detect it, but it has been broken for a decade.
Recently, I fixed modpost so it started to warn it again, then this
showed up in linux-next builds.
There are two ways to fix it:
- Remove __init
- Remove EXPORT_SYMBOL
I chose the latter for this case because the only in-tree call-site,
net/ipv4/xfrm4_policy.c is never compiled as modular.
(CONFIG_XFRM is boolean)
Fixes: 2f32b51b609f ("xfrm: Introduce xfrm_input_afinfo to access the the callbacks properly") Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Masahiro Yamada <masahiroy@kernel.org> Acked-by: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
EXPORT_SYMBOL and __init is a bad combination because the .init.text
section is freed up after the initialization. Hence, modules cannot
use symbols annotated __init. The access to a freed symbol may end up
with kernel panic.
modpost used to detect it, but it has been broken for a decade.
Recently, I fixed modpost so it started to warn it again, then this
showed up in linux-next builds.
There are two ways to fix it:
- Remove __init
- Remove EXPORT_SYMBOL
I chose the latter for this case because the only in-tree call-site,
drivers/net/phy/phy_device.c is never compiled as modular.
(CONFIG_PHYLIB is boolean)
Fixes: 90eff9096c01 ("net: phy: Allow splitting MDIO bus/device support from PHYs") Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Masahiro Yamada <masahiroy@kernel.org> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
I found that NFSD's new NFSv3 READDIRPLUS XDR encoder was screwing up
right at the end of the page array. xdr_get_next_encode_buffer() does
not compute the value of xdr->end correctly:
* The check to see if we're on the final available page in xdr->buf
needs to account for the space consumed by @nbytes.
* The new xdr->end value needs to account for the portion of @nbytes
that is to be encoded into the previous buffer.
Fixes: 2825a7f90753 ("nfsd4: allow encoding across page boundaries") Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Reviewed-by: NeilBrown <neilb@suse.de> Reviewed-by: J. Bruce Fields <bfields@fieldses.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
syzbot reported an illegal copy_to_user() attempt
from bpf_prog_get_info_by_fd() [1]
There was no repro yet on this bug, but I think
that commit 0aef499f3172 ("mm/usercopy: Detect vmalloc overruns")
is exposing a prior bug in bpf arm64.
bpf_prog_get_info_by_fd() looks at prog->jited_len
to determine if the JIT image can be copied out to user space.
My theory is that syzbot managed to get a prog where prog->jited_len
has been set to 43, while prog->bpf_func has ben cleared.
It is not clear why copy_to_user(uinsns, NULL, ulen) is triggering
this particular warning.
I thought find_vma_area(NULL) would not find a vm_struct.
As we do not hold vmap_area_lock spinlock, it might be possible
that the found vm_struct was garbage.
unix_dgram_poll() calls unix_dgram_peer_wake_me() without `other`'s
lock held and check if its receive queue is full. Here we need to
use unix_recvq_full_lockless() instead of unix_recvq_full(), otherwise
KCSAN will report a data-race.
of_find_device_by_node() takes reference, we should use put_device()
to release it when not need anymore.
Add missing put_device() to avoid refcount leak.
Fixes: 43f01da0f279 ("MIPS/OCTEON/ata: Convert pata_octeon_cf.c to use device tree.") Signed-off-by: Miaoqian Lin <linmq006@gmail.com> Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru> Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In pxa3xx_gcu_probe(), the sequence of error lable is wrong, it will
leads some resource leaked, so adjust the sequence to handle the error
correctly, and if pxa3xx_gcu_add_buffer() fails, pxa3xx_gcu_free_buffers()
need be called.
In pxa3xx_gcu_remove(), add missing clk_disable_unpreprare().
When doing layoutget as part of the open() compound, we have to be
careful to release the layout locks before we can call any further RPC
calls, such as setattr(). The reason is that those calls could trigger
a recall, which could deadlock.
When configuring a nommu classic m68k system enabling the uboot parameter
passing support (CONFIG_UBOOT) will produce the following compile error:
m68k-linux-ld: arch/m68k/kernel/uboot.o: in function `process_uboot_commandline':
uboot.c:(.init.text+0x32): undefined reference to `_init_sp'
The logic to support this option is only used on ColdFire based platforms
(in its head.S startup code). So make the selection of this option
depend on building for a ColdFire based platform.
The non-MMU m68k pagetable ZERO_PAGE() macro is being set to the
somewhat non-sensical value of "virt_to_page(0)". The zeroth page
is not in any way guaranteed to be a page full of "0". So the result
is that ZERO_PAGE() will almost certainly contain random values.
We already allocate a real "empty_zero_page" in the mm setup code shared
between MMU m68k and non-MMU m68k. It is just not hooked up to the
ZERO_PAGE() macro for the non-MMU m68k case.
Fix ZERO_PAGE() to use the allocated "empty_zero_page" pointer.
I am not aware of any specific issues caused by the old code.
Timeout as 1 second sets an upper limit on the length
of the transfer executed, but there is no maximum length
of a write or read message set in i2c_adapter_quirks for
this controller.
This upper limit affects devices that require sending
large firmware blobs over I2C.
To remove that limitation, calculate the minimal time
necessary, plus some wiggle room, for every message and
use it instead of the default one second, if more than
one second.
Signed-off-by: Lucas Tanure <tanureal@opensource.cirrus.com> Acked-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
To prepare for support asynchronous tracer_init_tracefs initcall,
avoid calling create_trace_option_files before __update_tracer_options.
Otherwise, create_trace_option_files will show warning because
some tracers in trace_types list are already in tr->topts.
For example, hwlat_tracer call register_tracer in late_initcall,
and global_trace.dir is already created in tracing_init_dentry,
hwlat_tracer will be put into tr->topts.
Then if the __update_tracer_options is executed after hwlat_tracer
registered, create_trace_option_files find that hwlat_tracer is
already in tr->topts.
When setting bootparams="trace_event=initcall:initcall_start tp_printk=1" in the
cmdline, the output_printk() was called, and the spin_lock_irqsave() was called in the
atomic and irq disable interrupt context suitation. On the PREEMPT_RT kernel,
these locks are replaced with sleepable rt-spinlock, so the stack calltrace will
be triggered.
Fix it by raw_spin_lock_irqsave when PREEMPT_RT and "trace_event=initcall:initcall_start
tp_printk=1" enabled.
The function percent_rmt_hitm_cmp() wrongly uses local HITMs for
sorting remote HITMs.
Since this function is to sort cache lines for remote HITMs, this patch
changes to use 'rmt_hitm' field for correct sorting.
Fixes: 9cb3500afc0980c5 ("perf c2c report: Add hitm/store percent related sort keys") Signed-off-by: Leo Yan <leo.yan@linaro.org> Acked-by: Namhyung Kim <namhyung@kernel.org> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Joe Mario <jmario@redhat.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Peter Zijlstra <peterz@infradead.org> Link: https://lore.kernel.org/r/20220530084253.750190-1-leo.yan@linaro.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In AFS, a directory is handled as a file that the client downloads and
parses locally for the purposes of performing lookup and getdents
operations. The in-kernel afs filesystem has a number of functions that
do this.
A directory file is arranged as a series of 2K blocks divided into
32-byte slots, where a directory entry occupies one or more slots, plus
each block starts with one or more metadata blocks.
When parsing a block, if the last slots are occupied by a dirent that
occupies more than a single slot and the file position points at a slot
that's not the initial one, the logic in afs_dir_iterate_block() that
skips over it won't advance the file pointer to the end of it. This
will cause an infinite loop in getdents() as it will keep retrying that
block and failing to advance beyond the final entry.
Fix this by advancing the file pointer if the next entry will be beyond
it when we skip a block.
This was found by the generic/676 xfstest but can also be triggered with
something like:
1) A new passive FastOpen TCP socket is created.
This FO socket waits for an ACK coming from client to be a complete
ESTABLISHED one.
2) A socket operation on this socket goes through lock_sock()
release_sock() dance.
3) While the socket is owned by the user in step 2),
a retransmit of the SYN is received and stored in socket backlog.
4) At release_sock() time, the socket backlog is processed while
in process context.
5) A SYNACK packet is cooked in response of the SYN retransmit.
6) -> tcp_rtx_synack() is called in process context.
Before blamed commit, tcp_rtx_synack() was always called from BH handler,
from a timer handler.
Fix this by using TCP_INC_STATS() & NET_INC_STATS()
which do not assume caller is in non preemptible context.
Some features (LRO, HW GRO) conflict with XDP. If there is an attempt to
enable such features while XDP is active, they will be set to `off
[requested on]`. In order to activate these features after XDP is turned
off, the driver needs to call netdev_update_features(). This commit adds
this missing call after XDP state changes.
Fixes: cf6e34c8c22f ("net/mlx5e: Properly block LRO when XDP is enabled") Fixes: b0617e7b3500 ("net/mlx5e: Properly block HW GRO when XDP is enabled") Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com> Reviewed-by: Tariq Toukan <tariqt@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
With the `-z unique-symbol` linker flag or any similar mechanism,
it is possible to trigger the following:
ERROR: modpost: "param_set_uint.0" [vmlinux] is a static EXPORT_SYMBOL
The reason is that for now the condition from remove_dot():
if (m && (s[n + m] == '.' || s[n + m] == 0))
which was designed to test if it's a dot or a '\0' after the suffix
is never satisfied.
This is due to that `s[n + m]` always points to the last digit of a
numeric suffix, not on the symbol next to it (from a custom debug
print added to modpost):
param_set_uint.0, s[n + m] is '0', s[n + m + 1] is '\0'
So it's off-by-one and was like that since 2014.
Fix this for the sake of any potential upcoming features, but don't
bother stable-backporting, as it's well hidden -- apart from that
LD flag, it can be triggered only with GCC LTO which never landed
upstream.
of_get_child_by_name() returns a node pointer with refcount
incremented, we should use of_node_put() on it when done.
mv88e6xxx_mdio_register() pass the device node to of_mdiobus_register().
We don't need the device node after it.
Add missing of_node_put() to avoid refcount leak.
Fixes: a3c53be55c95 ("net: dsa: mv88e6xxx: Support multiple MDIO busses") Signed-off-by: Miaoqian Lin <linmq006@gmail.com> Reviewed-by: Marek Behún <kabel@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The "fsp->location" variable comes from user via ethtool_get_rxnfc().
Check that it is valid to prevent an out of bounds read.
Fixes: 7aab747e5563 ("net: ethernet: mediatek: add ethtool functions to configure RX flows of HW LRO") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The argument of scatterwalk_unmap() is supposed to be the void* that was
returned by the previous scatterwalk_map() call.
The s390 AES-GCM implementation was instead passing the pointer to the
struct scatter_walk.
This doesn't actually break anything because scatterwalk_unmap() only uses
its argument under CONFIG_HIGHMEM and ARCH_HAS_FLUSH_ON_KUNMAP.
We can get "failed to disable" clock_unprepare warnings on unbind at least
for the serial console device if the unbind is done before the device has
been idled.
As some devices are using deferred idle, we must check the status for
pending idle work to idle the device.
Add CSIZE sanitization for unsupported CSIZE configurations. In
addition, if parity is asked for but CSx was unsupported, the sensible
result is CS8+parity which requires setting USART_CR1_M0 like with 9
bits.
Incorrect CSIZE results in miscalculation of the frame bits in
tty_get_char_size() or in its predecessor where the roughly the same
code is directly within uart_update_timeout().
Fixes: c8a9d043947b (serial: stm32: fix word length configuration) Cc: Erwan Le Ray <erwan.leray@st.com> Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Link: https://lore.kernel.org/r/20220519081808.3776-9-ilpo.jarvinen@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Only CS7 and CS8 seem supported but CSIZE is not sanitized from CS5 or
CS6 to CS8. In addition, ASC_CTL_MODE_7BIT_PAR suggests that CS7 has
to have parity, thus add PARENB.
Incorrect CSIZE results in miscalculation of the frame bits in
tty_get_char_size() or in its predecessor where the roughly the same
code is directly within uart_update_timeout().
Only CS7 and CS8 seem supported but CSIZE is not sanitized from
CS5 or CS6 to CS8.
Set CSIZE correctly so that userspace knows the effective value.
Incorrect CSIZE also results in miscalculation of the frame bits in
tty_get_char_size() or in its predecessor where the roughly the same
code is directly within uart_update_timeout().
Only CS7 and CS8 are supported but CSIZE is not sanitized with
CS5 or CS6 to CS8.
Set CSIZE correctly so that userspace knows the effective value.
Incorrect CSIZE also results in miscalculation of the frame bits in
tty_get_char_size() or in its predecessor where the roughly the same
code is directly within uart_update_timeout().
Only CS7 and CS8 seem supported but CSIZE is not sanitized to CS8 in
the default: block.
Set CSIZE correctly so that userspace knows the effective value.
Incorrect CSIZE also results in miscalculation of the frame bits in
tty_get_char_size() or in its predecessor where the roughly the same
code is directly within uart_update_timeout().
SER_RS485_RTS_ON_SEND and SER_RS485_RTS_AFTER_SEND relate to behavior
within RS485 operation. The driver checks if they have the same value
which is not possible to realize with the hardware. The check is taken
regardless of SER_RS485_ENABLED flag and -EINVAL is returned when the
check fails, which creates problems.
This check makes it unnecessarily complicated to turn RS485 mode off as
simple zeroed serial_rs485 struct will trigger that equal values check.
In addition, the driver itself memsets its rs485 structure to zero when
RS485 is disabled but if userspace would try to make an TIOCSRS485
ioctl() call with the very same struct, it would end up failing with
-EINVAL which doesn't make much sense.
Resolve the problem by moving the check inside SER_RS485_ENABLED block.
The uart_ops startup() callback is called without interrupts
disabled and without port->lock locked, relatively late during the
boot process (from the call path of console_on_rootfs()). If the
device is a console, it was already previously registered and could
be actively printing messages.
Since the startup() callback is reading/writing registers used by
the console write() callback (AML_UART_CONTROL), its access must
be synchronized using the port->lock. Currently it is not.
The startup() callback is the only function that explicitly enables
interrupts. Without the synchronization, it is possible that
interrupts become accidentally permanently disabled.
Some implementations of the SBI time extension depend on hart-local
state (for example, CSRs) that are lost or hardware that is powered
down when a CPU is suspended. To be safe, the clockevents driver
cannot assume that timer IRQs will be received during CPU suspend.
Fixes: 62b019436814 ("clocksource: new RISC-V SBI timer driver") Signed-off-by: Samuel Holland <samuel@sholland.org> Reviewed-by: Anup Patel <anup@brainfault.org> Link: https://lore.kernel.org/r/20220509012121.40031-1-samuel@sholland.org Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
of_find_matching_node_and_match returns a node pointer with refcount
incremented, we should use of_node_put() on it when done.
Add missing of_node_put() to avoid refcount leak.
The panic notifier infrastructure executes registered callbacks when
a panic event happens - such callbacks are executed in atomic context,
with interrupts and preemption disabled in the running CPU and all other
CPUs disabled. That said, mutexes in such context are not a good idea.
This patch replaces a regular mutex with a mutex_trylock safer approach;
given the nature of the mutex used in the driver, it should be pretty
uncommon being unable to acquire such mutex in the panic path, hence
no functional change should be observed (and if it is, that would be
likely a deadlock with the regular mutex).
Fixes: 2227b7c74634 ("coresight: add support for CPU debug module") Cc: Leo Yan <leo.yan@linaro.org> Cc: Mathieu Poirier <mathieu.poirier@linaro.org> Cc: Mike Leach <mike.leach@linaro.org> Cc: Suzuki K Poulose <suzuki.poulose@arm.com> Signed-off-by: Guilherme G. Piccoli <gpiccoli@igalia.com> Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com> Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com> Link: https://lore.kernel.org/r/20220427224924.592546-10-gpiccoli@igalia.com Signed-off-by: Sasha Levin <sashal@kernel.org>
If the device is already in a runtime PM enabled state
pm_runtime_get_sync() will return 1, so a test for negative
value should be used to check for errors.
The hardware only supports periods <= 1.6 ms and if a bigger period is
requested it is clamped to 1.6 ms. In this case duty_cycle might be bigger
than 1.6 ms and then the duty cycle register is written with a value
bigger than LP3943_MAX_DUTY. So clamp duty_cycle accordingly.
The function documentation of usb_set_configuration says that its
callers should hold the device lock. This lock is held for all
callsites except tweak_set_configuration_cmd. The code path can be
executed for example when attaching a remote USB device.
The solution is to surround the call by the device lock.
This bug was found using my experimental own-developed static analysis
tool, which reported the missing lock on v5.17.2. I manually verified
this bug report by doing code review as well. I runtime checked that
the required lock is not held. I compiled and runtime tested this on
x86_64 with a USB mouse. After applying this patch, my analyser no
longer reports this potential bug.
In goldfish_tty_probe(), the port initialized through tty_port_init()
should be destroyed in error paths.In goldfish_tty_remove(), qtty->port
also should be destroyed or else might leak resources.
If the list does not exit early then data == NULL and 'module' does not
point to a valid list element.
Using 'module' in such a case is not valid and was therefore removed.
Fixes: 6dd67645f22c ("greybus: audio: Use single codec driver registration") Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by: Vaibhav Agarwal <vaibhav.sr@gmail.com> Reviewed-by: Mark Greer <mgreer@animalcreek.com> Signed-off-by: Jakob Koschel <jakobkoschel@gmail.com> Link: https://lore.kernel.org/r/20220321123626.3068639-1-jakobkoschel@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When the MIPS_ALCHEMY board selection is MIPS_XXS1500 instead of
MIPS_DB1XXX, the PCMCIA driver 'db1xxx_ss' has build errors due
to missing DB1XXX symbols. The PCMCIA driver should be restricted
to MIPS_DB1XXX instead of MIPS_ALCHEMY to fix this build error.
Remove unsupported forcing of `cpu_has_fpu' to 1, which makes the `nofpu'
kernel parameter non-functional, and also causes a link error:
ld: arch/mips/kernel/traps.o: in function `trap_init':
./arch/mips/include/asm/msa.h:(.init.text+0x348): undefined reference to `handle_fpe'
ld: ./arch/mips/include/asm/msa.h:(.init.text+0x354): undefined reference to `handle_fpe'
ld: ./arch/mips/include/asm/msa.h:(.init.text+0x360): undefined reference to `handle_fpe'
where the CONFIG_MIPS_FP_SUPPORT configuration option has been disabled.
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk> Reported-by: Stephen Zhang <starzhangzsd@gmail.com> Fixes: 0ebb2f4159af ("MIPS: IP27: Update/restructure CPU overrides") Cc: stable@vger.kernel.org # v4.2+ Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Current rxe_requester() doesn't generate a completion when processing an
unsupported/invalid opcode. If rxe driver doesn't support a new opcode
(e.g. RDMA Atomic Write) and RDMA library supports it, an application
using the new opcode can reproduce this issue. Fix the issue by calling
"goto err;".
iolatency needs to track the number of inflight IOs per cgroup. As this
tracking can be expensive, it is disabled when no cgroup has iolatency
configured for the device. To ensure that the inflight counters stay
balanced, iolatency_set_limit() freezes the request_queue while manipulating
the enabled counter, which ensures that no IO is in flight and thus all
counters are zero.
Unfortunately, iolatency_set_limit() isn't the only place where the enabled
counter is manipulated. iolatency_pd_offline() can also dec the counter and
trigger disabling. As this disabling happens without freezing the q, this
can easily happen while some IOs are in flight and thus leak the counts.
This can be easily demonstrated by turning on iolatency on an one empty
cgroup while IOs are in flight in other cgroups and then removing the
cgroup. Note that iolatency shouldn't have been enabled elsewhere in the
system to ensure that removing the cgroup disables iolatency for the whole
device.
The following keeps flipping on and off iolatency on sda:
If a cgroup with stuck inflight ends up getting throttled, the throttled IOs
will never get issued as there's no completion event to wake it up leading
to an indefinite hang.
This patch fixes the bug by unifying enable handling into a work item which
is automatically kicked off from iolatency_set_min_lat_nsec() which is
called from both iolatency_set_limit() and iolatency_pd_offline() paths.
Punting to a work item is necessary as iolatency_pd_offline() is called
under spinlocks while freezing a request_queue requires a sleepable context.
This also simplifies the code reducing LOC sans the comments and avoids the
unnecessary freezes which were happening whenever a cgroup's latency target
is newly set or cleared.
Signed-off-by: Tejun Heo <tj@kernel.org> Cc: Josef Bacik <josef@toxicpanda.com> Cc: Liu Bo <bo.liu@linux.alibaba.com> Fixes: 8c772a9bfc7c ("blk-iolatency: fix IO hang due to negative inflight counter") Cc: stable@vger.kernel.org # v5.0+ Link: https://lore.kernel.org/r/Yn9ScX6Nx2qIiQQi@slm.duckdns.org Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The list iterator value 'crtc' will *always* be set and non-NULL by
list_for_each_entry(), so it is incorrect to assume that the iterator
value will be NULL if the list is empty or no element is found.
To fix the bug, return 'crtc' when found, otherwise return NULL.
If the previous list_for_each_entry_continue_rcu() don't exit early
(no goto hit inside the loop), the iterator 'cvif' after the loop
will be a bogus pointer to an invalid structure object containing
the HEAD (&ar->vif_list). As a result, the use of 'cvif' after that
will lead to a invalid memory access (i.e., 'cvif->id': the invalid
pointer dereference when return back to/after the callsite in the
carl9170_update_beacon()).
The original intention should have been to return the valid 'cvif'
when found in list, NULL otherwise. So just return NULL when no
entry found, to fix this bug.
Cc: stable@vger.kernel.org Fixes: 1f1d9654e183c ("carl9170: refactor carl9170_update_beacon") Signed-off-by: Xiaomeng Tong <xiam0nd.tong@gmail.com> Acked-by: Christian Lamparter <chunkeey@gmail.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20220328122820.1004-1-xiam0nd.tong@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver has a custom put function for "DSP Voice Wake Up" which does
not generate event notifications on change, instead returning 0. Since we
already exit early in the case that there is no change this can be fixed
by unconditionally returning 1 at the end of the function.
Using not existing queues can panic the kernel with rtl8180/rtl8185 cards.
Ignore the skb priority for those cards, they only have one tx queue. Pierre
Asselin (pa@panix.com) reported the kernel crash in the Gentoo forum:
He also confirmed that this patch fixes the issue. In summary this happened:
After updating wpa_supplicant from 2.9 to 2.10 the kernel crashed with a
"divide error: 0000" when connecting to an AP. Control port tx now tries to
use IEEE80211_AC_VO for the priority, which wpa_supplicants starts to use in
2.10.
Since only the rtl8187se part of the driver supports QoS, the priority
of the skb is set to IEEE80211_AC_BE (2) by mac80211 for rtl8180/rtl8185
cards.
rtl8180 is then unconditionally reading out the priority and finally crashes on
drivers/net/wireless/realtek/rtl818x/rtl8180/dev.c line 544 without this
patch:
idx = (ring->idx + skb_queue_len(&ring->queue)) % ring->entries
"ring->entries" is zero for rtl8180/rtl8185 cards, tx_ring[2] never got
initialized.
Cc: stable@vger.kernel.org Reported-by: pa@panix.com Tested-by: pa@panix.com Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20220422145228.7567-1-alexander@wetzel-home.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The routine huge_pmd_unshare() is passed a pointer to an address
associated with an area which may be unshared. If unshare is successful
this address is updated to 'optimize' callers iterating over huge page
addresses. For the optimization to work correctly, address should be
updated to the last huge page in the unmapped/unshared area. However, in
the common case where the passed address is PUD_SIZE aligned, the address
is incorrectly updated to the address of the preceding huge page. That
wastes CPU cycles as the unmapped/unshared range is scanned twice.
Link: https://lkml.kernel.org/r/20220524205003.126184-1-mike.kravetz@oracle.com Fixes: 39dde65c9940 ("shared page table for hugetlb page") Signed-off-by: Mike Kravetz <mike.kravetz@oracle.com> Acked-by: Muchun Song <songmuchun@bytedance.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With gcc version 12.0.1 20220401 (Red Hat 12.0.1-0), building with
defconfig results in the following compilation error:
| CC mm/swapfile.o
| mm/swapfile.c: In function `setup_swap_info':
| mm/swapfile.c:2291:47: error: array subscript -1 is below array bounds
| of `struct plist_node[]' [-Werror=array-bounds]
| 2291 | p->avail_lists[i].prio = 1;
| | ~~~~~~~~~~~~~~^~~
| In file included from mm/swapfile.c:16:
| ./include/linux/swap.h:292:27: note: while referencing `avail_lists'
| 292 | struct plist_node avail_lists[]; /*
| | ^~~~~~~~~~~
This is due to the compiler detecting that the mask in
node_states[__state] could theoretically be zero, which would lead to
first_node() returning -1 through find_first_bit.
I believe that the warning/error is legitimate. I first tried adding a
test to check that the node mask is not emtpy, since a similar test exists
in the case where MAX_NUMNODES == 1.
However, adding the if statement causes other warnings to appear in
for_each_cpu_node_but, because it introduces a dangling else ambiguity.
And unfortunately, GCC is not smart enough to detect that the added test
makes the case where (node) == -1 impossible, so it still complains with
the same message.
This is why I settled on replacing that with a harmless, but relatively
useless (node) >= 0 test. Based on the warning for the dangling else, I
also decided to fix the case where MAX_NUMNODES == 1 by moving the
condition inside the for loop. It will still only be tested once. This
ensures that the meaning of an else following for_each_node_mask or
derivatives would not silently have a different meaning depending on the
configuration.
Link: https://lkml.kernel.org/r/20220414150855.2407137-3-dinechin@redhat.com Signed-off-by: Christophe de Dinechin <christophe@dinechin.org> Signed-off-by: Christophe de Dinechin <dinechin@redhat.com> Reviewed-by: Andrew Morton <akpm@linux-foundation.org> Cc: Ben Segall <bsegall@google.com> Cc: "Michael S. Tsirkin" <mst@redhat.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Ingo Molnar <mingo@redhat.com> Cc: Mel Gorman <mgorman@suse.de> Cc: Dietmar Eggemann <dietmar.eggemann@arm.com> Cc: Vincent Guittot <vincent.guittot@linaro.org> Cc: Paolo Bonzini <pbonzini@redhat.com> Cc: Daniel Bristot de Oliveira <bristot@redhat.com> Cc: Jason Wang <jasowang@redhat.com> Cc: Zhen Lei <thunder.leizhen@huawei.com> Cc: Juri Lelli <juri.lelli@redhat.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The bug is here:
if (!iommu || iommu->dev->of_node != spec->np) {
The list iterator value 'iommu' will *always* be set and non-NULL by
list_for_each_entry(), so it is incorrect to assume that the iterator
value will be NULL if the list is empty or no element is found (in fact,
it will point to a invalid structure object containing HEAD).
To fix the bug, use a new value 'iter' as the list iterator, while use
the old value 'iommu' as a dedicated variable to point to the found one,
and remove the unneeded check for 'iommu->dev->of_node != spec->np'
outside the loop.
syscall_stub_data() expects the data_count parameter to be the number of
longs, not bytes.
==================================================================
BUG: KASAN: stack-out-of-bounds in syscall_stub_data+0x70/0xe0
Read of size 128 at addr 000000006411f6f0 by task swapper/1
The previous fix here was only partially correct, it did
result in returning a proper error value in case of error,
but it also clobbered the pid that we need to return from
this function (not just zero for success).
As a result, it returned 0 here, but later this is treated
as a pid and used to kill the process, but since it's now
0 we kill(0, SIGKILL), which makes UML kill itself rather
than just the helper thread.
Fix that and make it more obvious by using a separate
variable for the pid.
Fixes: ccf1236ecac4 ("um: fix error return code in winch_tramp()") Reported-and-tested-by: Nathan Chancellor <nathan@kernel.org> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Cc: stable@vger.kernel.org Signed-off-by: Richard Weinberger <richard@nod.at> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In client mode, we can't connect to hidden SSID APs or SSIDs not advertised
in beacons on DFS channels, since we're forced to passive scan. Fix this by
sending out a probe request immediately after the first beacon, if active
scan was requested by the user.
Cc: stable@vger.kernel.org Reported-by: Catrinel Catrinescu <cc@80211.de> Signed-off-by: Felix Fietkau <nbd@nbd.name> Link: https://lore.kernel.org/r/20220420104907.36275-1-nbd@nbd.name Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When irq-xtensa-mx chip is used in non-SMP configuration its
irq_set_affinity callback is not called leaving IRQ affinity set empty.
As a result IRQ delivery does not work in that configuration.
Initialize IRQ affinity of the xtensa MX interrupt distributor to CPU 0
for all external IRQ lines.
Cc: stable@vger.kernel.org Signed-off-by: Max Filippov <jcmvbkbc@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Register ARMADA_370_XP_INT_FABRIC_MASK_OFFS is Armada 370 and XP specific
and on new Armada platforms it has different meaning. It does not configure
Performance Counter Overflow interrupt masking. So do not touch this
register on non-A370/XP platforms (A375, A38x and A39x).
Signed-off-by: Pali Rohár <pali@kernel.org> Cc: stable@vger.kernel.org Fixes: 28da06dfd9e4 ("irqchip: armada-370-xp: Enable the PMU interrupts") Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Marc Zyngier <maz@kernel.org> Link: https://lore.kernel.org/r/20220425113706.29310-1-pali@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When multiplying of different types, an overflow is possible even when
storing the result in a larger type. This is because the conversion is
done after the multiplication. So arithmetic overflow and thus in
incorrect value is possible.
Correct an instance of this in the inter packet delay calculation. Fix by
ensuring one of the operands is u64 which will promote the other to u64 as
well ensuring no overflow.
Cc: stable@vger.kernel.org Fixes: 7724105686e7 ("IB/hfi1: add driver files") Link: https://lore.kernel.org/r/20220520183712.48973.29855.stgit@awfm-01.cornelisnetworks.com Reviewed-by: Mike Marciniszyn <mike.marciniszyn@cornelisnetworks.com> Signed-off-by: Dennis Dalessandro <dennis.dalessandro@cornelisnetworks.com> Signed-off-by: Jason Gunthorpe <jgg@nvidia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add H264 level 1.0, 4.1, 4.2 to the list of supported formats.
While the hardware does not fully support these levels, it does support
most of them. The constraints on frame size and pixel formats already
cover the limitation.
This fixes negotiation of level on GStreamer 1.17.1.
The CODA960 manual states that ASO/FMO features of baseline are not
supported, so for this reason this driver should only report
constrained baseline support.
This fixes negotiation issue with constrained baseline content
on GStreamer 1.17.1.
ASO/FMO features are unsupported for the encoder and untested for the
decoder because there is currently no userspace support. Neither GStreamer
parsers nor FFMPEG parsers support ASO/FMO.
The bug is here:
if (!rdev || rdev->desc_nr != nr) {
The list iterator value 'rdev' will *always* be set and non-NULL
by rdev_for_each_rcu(), so it is incorrect to assume that the
iterator value will be NULL if the list is empty or no element
found (In fact, it will be a bogus pointer to an invalid struct
object containing the HEAD). Otherwise it will bypass the check
and lead to invalid memory access passing the check.
To fix the bug, use a new variable 'iter' as the list iterator,
while using the original variable 'pdev' as a dedicated pointer to
point to the found element.
Cc: stable@vger.kernel.org Fixes: 70bcecdb1534 ("md-cluster: Improve md_reload_sb to be less error prone") Signed-off-by: Xiaomeng Tong <xiam0nd.tong@gmail.com> Signed-off-by: Song Liu <song@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The list iterator value 'rdev' will *always* be set and non-NULL
by rdev_for_each(), so it is incorrect to assume that the iterator
value will be NULL if the list is empty or no element found.
Otherwise it will bypass the NULL check and lead to invalid memory
access passing the check.
To fix the bug, use a new variable 'iter' as the list iterator,
while using the original variable 'rdev' as a dedicated pointer to
point to the found element.
Cc: stable@vger.kernel.org Fixes: 2aa82191ac36 ("md-cluster: Perform a lazy update") Acked-by: Guoqing Jiang <guoqing.jiang@linux.dev> Signed-off-by: Xiaomeng Tong <xiam0nd.tong@gmail.com> Acked-by: Goldwyn Rodrigues <rgoldwyn@suse.com> Signed-off-by: Song Liu <song@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the display is not enable()d, then we aren't holding a runtime PM
reference here. Thus, it's easy to accidentally cause a hang, if user
space is poking around at /dev/drm_dp_aux0 at the "wrong" time.
Let's get a runtime PM reference, and check that we "see" the panel.
Don't force any panel power-up, etc., because that can be intrusive, and
that's not what other drivers do (see
drivers/gpu/drm/bridge/ti-sn65dsi86.c and
drivers/gpu/drm/bridge/parade-ps8640.c.)
Fixes: 0d97ad03f422 ("drm/bridge: analogix_dp: Remove duplicated code") Cc: <stable@vger.kernel.org> Cc: Tomeu Vizoso <tomeu.vizoso@collabora.com> Signed-off-by: Brian Norris <briannorris@chromium.org> Reviewed-by: Douglas Anderson <dianders@chromium.org> Signed-off-by: Douglas Anderson <dianders@chromium.org> Link: https://patchwork.freedesktop.org/patch/msgid/20220301181107.v4.1.I773a08785666ebb236917b0c8e6c05e3de471e75@changeid Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The bug is here:
if (nvkm_cstate_valid(clk, cstate, max_volt, clk->temp))
return cstate;
The list iterator value 'cstate' will *always* be set and non-NULL
by list_for_each_entry_from_reverse(), so it is incorrect to assume
that the iterator value will be unchanged if the list is empty or no
element is found (In fact, it will be a bogus pointer to an invalid
structure object containing the HEAD). Also it missed a NULL check
at callsite and may lead to invalid memory access after that.
To fix this bug, just return 'encoder' when found, otherwise return
NULL. And add the NULL check.
Cc: stable@vger.kernel.org Fixes: 1f7f3d91ad38a ("drm/nouveau/clk: Respect voltage limits in nvkm_cstate_prog") Signed-off-by: Xiaomeng Tong <xiam0nd.tong@gmail.com> Reviewed-by: Lyude Paul <lyude@redhat.com> Signed-off-by: Lyude Paul <lyude@redhat.com> Link: https://patchwork.freedesktop.org/patch/msgid/20220327075824.11806-1-xiam0nd.tong@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In ufs_qcom_dev_ref_clk_ctrl(), it was noted that the ref_clk needs to be
stable for at least 1us. Even though there is wmb() to make sure the write
gets "completed", there is no guarantee that the write actually reached the
UFS device. There is a good chance that the write could be stored in a
Write Buffer (WB). In that case, even though the CPU waits for 1us, the
ref_clk might not be stable for that period.
So lets do a readl() to make sure that the previous write has reached the
UFS device before udelay().
Also, the wmb() after writel_relaxed() is not really needed. Both writel()
and readl() are ordered on all architectures and the CPU won't speculate
instructions after readl() due to the in-built control dependency with read
value on weakly ordered architectures. So it can be safely removed.
Link: https://lore.kernel.org/r/20220504084212.11605-4-manivannan.sadhasivam@linaro.org Fixes: f06fcc7155dc ("scsi: ufs-qcom: add QUniPro hardware support and power optimizations") Cc: stable@vger.kernel.org Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / thirdparty / kernel / stable.git / log
