According to MT7622 Reference Manual for Development Board v1.0 the PWM
unit found in the MT7622 SoC also comes with the PWM_CK_26M_SEL register
at offset 0x210 just like other modern MediaTek ARM64 SoCs.
And also MT7622 sets that register to 0x00000001 on reset which is
described as 'Select 26M fix CLK as BCLK' in the datasheet.
Hence set has_ck_26m_sel to true also for MT7622 which results in the
driver writing 0 to the PWM_CK_26M_SEL register which is described as
'Select bus CLK as BCLK'.
Fixes: 0c0ead76235db0 ("pwm: mediatek: Always use bus clock") Signed-off-by: Daniel Golle <daniel@makrotopia.org> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Link: https://lore.kernel.org/r/Y1iF2slvSblf6bYK@makrotopia.org Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Thierry Reding <thierry.reding@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Do not set 'HCI_UART_PROTO_READY' before call 'hci_uart_register_dev()'.
Possible race is when someone calls 'hci_tty_uart_close()' after this bit
is set, but 'hci_uart_register_dev()' wasn't done. This leads to access
to uninitialized fields. To fix it let's set this bit after device was
registered (as before patch c411c62cc133) and to fix previous problem let's
add one more bit in addition to 'HCI_UART_PROTO_READY' which allows to
perform power up without original bit set (pls see commit c411c62cc133).
While debugging kexec/hibernation hangs and crashes, it turned out that
the current implementation of e820__register_nosave_regions() suffers from
multiple serious issues:
- The end of last region is tracked by PFN, causing it to find holes
that aren't there if two consecutive subpage regions are present
- The nosave PFN ranges derived from holes are rounded out (instead of
rounded in) which makes it inconsistent with how explicitly reserved
regions are handled
Fix this by:
- Treating reserved regions as if they were holes, to ensure consistent
handling (rounding out nosave PFN ranges is more correct as the
kernel does not use partial pages)
- Tracking the end of the last RAM region by address instead of pages
to detect holes more precisely
These bugs appear to have been introduced about ~18 years ago with the very
first version of e820_mark_nosave_regions(), and its flawed assumptions were
carried forward uninterrupted through various waves of rewrites and renames.
[ mingo: Added Git archeology details, for kicks and giggles. ]
Fixes: e8eff5ac294e ("[PATCH] Make swsusp avoid memory holes and reserved memory regions on x86_64") Reported-by: Roberto Ricci <io@r-ricci.it> Tested-by: Roberto Ricci <io@r-ricci.it> Signed-off-by: Myrrh Periwinkle <myrrhperiwinkle@qtmlabs.xyz> Signed-off-by: Ingo Molnar <mingo@kernel.org> Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Cc: Ard Biesheuvel <ardb@kernel.org> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Kees Cook <keescook@chromium.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: David Woodhouse <dwmw@amazon.co.uk> Cc: Len Brown <len.brown@intel.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20250406-fix-e820-nosave-v3-1-f3787bc1ee1d@qtmlabs.xyz Closes: https://lore.kernel.org/all/Z4WFjBVHpndct7br@desktop0a/ Signed-off-by: Myrrh Periwinkle <myrrhperiwinkle@qtmlabs.xyz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When submitting the TLMM test driver, Bjorn reported that some of the test
cases are failing for GPIOs that not are backed by PDC (i.e. "non-wakeup"
GPIOs that are handled directly in pinctrl-msm). Basically, lingering
latched interrupt state is still being delivered at IRQ request time, e.g.:
ok 1 tlmm_test_silent_rising
tlmm_test_silent_falling: ASSERTION FAILED at drivers/pinctrl/qcom/tlmm-test.c:178
Expected atomic_read(&priv->intr_count) == 0, but
atomic_read(&priv->intr_count) == 1 (0x1)
not ok 2 tlmm_test_silent_falling
tlmm_test_silent_low: ASSERTION FAILED at drivers/pinctrl/qcom/tlmm-test.c:178
Expected atomic_read(&priv->intr_count) == 0, but
atomic_read(&priv->intr_count) == 1 (0x1)
not ok 3 tlmm_test_silent_low
ok 4 tlmm_test_silent_high
Whether to report interrupts that came in while the IRQ was unclaimed
doesn't seem to be well-defined in the Linux IRQ API. However, looking
closer at these specific cases, we're actually reporting events that do not
match the interrupt type requested by the driver:
1. After "ok 1 tlmm_test_silent_rising", the GPIO is in low state and
configured for IRQF_TRIGGER_RISING.
2. (a) In preparation for "tlmm_test_silent_falling", the GPIO is switched
to high state. The rising interrupt gets latched.
(b) The GPIO is re-configured for IRQF_TRIGGER_FALLING, but the latched
interrupt isn't cleared.
(c) The IRQ handler is called for the latched interrupt, but there
wasn't any falling edge.
3. (a) For "tlmm_test_silent_low", the GPIO remains in high state.
(b) The GPIO is re-configured for IRQF_TRIGGER_LOW. This seems to
result in a phantom interrupt that gets latched.
(c) The IRQ handler is called for the latched interrupt, but the GPIO
isn't in low state.
4. (a) For "tlmm_test_silent_high", the GPIO is switched to low state.
(b) This doesn't result in a latched interrupt, because RAW_STATUS_EN
was cleared when masking the level-triggered interrupt.
Fix this by clearing the interrupt state whenever making any changes to the
interrupt configuration. This includes previously disabled interrupts, but
also any changes to interrupt polarity or detection type.
With this change, all 16 test cases are now passing for the non-wakeup
GPIOs in the TLMM.
If device_register(&child->dev) fails, call put_device() to explicitly
release child->dev, per the comment at device_register().
Found by code review.
Link: https://lore.kernel.org/r/20250202062357.872971-1-make24@iscas.ac.cn Fixes: 4f535093cf8f ("PCI: Put pci_dev in device tree as early as possible") Signed-off-by: Ma Ke <make24@iscas.ac.cn> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A call to of_parse_phandle() is incrementing the refcount, and as such,
the of_node_put() must be called when the reference is no longer needed.
Thus, refactor the existing code and add a missing of_node_put() call
following the check to ensure that "msi_np" matches "pcie->np" and after
MSI initialization, but only if the MSI support is enabled system-wide.
of_irq_init() will leak interrupt controller device node refcounts
in two places as explained below:
1) Leak refcounts of both @desc->dev and @desc->interrupt_parent when
suffers @desc->irq_init_cb() failure.
2) Leak refcount of @desc->interrupt_parent when cleans up list
@intc_desc_list in the end.
Refcounts of both @desc->dev and @desc->interrupt_parent were got in
the first loop, but of_irq_init() does not put them before kfree(@desc)
in places mentioned above, so causes refcount leakages.
Fix by putting refcounts involved before kfree(@desc).
In irq_of_parse_and_map(), refcount of device node @oirq.np was got
by successful of_irq_parse_one() invocation, but it does not put the
refcount before return, so causes @oirq.np refcount leakage.
Fix by putting @oirq.np refcount before return.
Fixes: e3873444990d ("of/irq: Move irq_of_parse_and_map() to common code") Cc: stable@vger.kernel.org Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com> Link: https://lore.kernel.org/r/20250209-of_irq_fix-v2-6-93e3a2659aa7@quicinc.com Signed-off-by: Rob Herring (Arm) <robh@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
of_irq_count() invokes of_irq_parse_one() to count IRQs, and successful
invocation of the later will get device node @irq.np refcount, but the
former does not put the refcount before next iteration invocation, hence
causes device node refcount leakages.
Fix by putting @irq.np refcount before the next iteration invocation.
msi_db_mask is of type 'u64', still the standard 'int' arithmetic is
performed to compute its value.
While most of the ntb_hw drivers actually don't utilize the higher 32
bits of the doorbell mask now, this may be the case for Switchtec - see
switchtec_ntb_init_db().
Found by Linux Verification Center (linuxtesting.org) with SVACE static
analysis tool.
Fixes: 2b0569b3b7e6 ("NTB: Add MSI interrupt support to ntb_transport") Cc: stable@vger.kernel.org Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru> Reviewed-by: Dave Jiang <dave.jiang@intel.com> Signed-off-by: Jon Mason <jdmason@kudzu.us> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the kernel contains a large number of functions that can be traced,
the loop in ftrace_graph_set_hash() may take a lot of time to execute.
This may trigger the softlockup watchdog.
Add cond_resched() within the loop to allow the kernel to remain
responsive even when processing a large number of functions.
This matches the cond_resched() that is used in other locations of the
code that iterates over all functions that can be traced.
Cc: stable@vger.kernel.org Fixes: b9b0c831bed26 ("ftrace: Convert graph filter to use hash tables") Link: https://lore.kernel.org/tencent_3E06CE338692017B5809534B9C5C03DA7705@qq.com Signed-off-by: zhoumin <teczm@foxmail.com> Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, the ASP primary device check does not have support for PCI
domains, and, as a result, when the system is configured with PCI domains
(PCI segments) the wrong device can be selected as primary. This results
in commands submitted to the device timing out and failing. The device
check also relies on specific device and function assignments that may
not hold in the future.
Fix the primary ASP device check to include support for PCI domains and
to perform proper checking of the Bus/Device/Function positions.
The mapping table for the rk3328 is missing the entry for -25C which is
found in the TRM section 9.5.2 "Temperature-to-code mapping".
NOTE: the kernel uses the tsadc_q_sel=1'b1 mode which is defined as:
4096-<code in table>. Whereas the table in the TRM gives the code
"3774" for -25C, the kernel uses 4096-3774=322.
[Dragan Simic] : "After going through the RK3308 and RK3328 TRMs, as
well as through the downstream kernel code, it seems we may have
some troubles at our hands. Let me explain, please.
To sum it up, part 1 of the RK3308 TRM v1.1 says on page 538 that
the equation for the output when tsadc_q_sel equals 1 is (4096 -
tsadc_q), while part 1 of the RK3328 TRM v1.2 says that the output
equation is (1024 - tsadc_q) in that case.
The downstream kernel code, however, treats the RK3308 and RK3328
tables and their values as being the same. It even mentions 1024 as
the "offset" value in a comment block for the rk_tsadcv3_control()
function, just like the upstream code does, which is obviously wrong
"offset" value when correlated with the table on page 544 of part 1
of the RK3308 TRM v1.1.
With all this in mind, it's obvious that more work is needed to make
it clear where's the actual mistake (it could be that the TRM is
wrong), which I'll volunteer for as part of the SoC binning project.
In the meantime, this patch looks fine as-is to me, by offering
what's a clear improvement to the current state of the upstream
code"
sctp_sendmsg() re-uses associations and transports when possible by
doing a lookup based on the socket endpoint and the message destination
address, and then sctp_sendmsg_to_asoc() sets the selected transport in
all the message chunks to be sent.
There's a possible race condition if another thread triggers the removal
of that selected transport, for instance, by explicitly unbinding an
address with setsockopt(SCTP_SOCKOPT_BINDX_REM), after the chunks have
been set up and before the message is sent. This can happen if the send
buffer is full, during the period when the sender thread temporarily
releases the socket lock in sctp_wait_for_sndbuf().
This causes the access to the transport data in
sctp_outq_select_transport(), when the association outqueue is flushed,
to result in a use-after-free read.
This change avoids this scenario by having sctp_transport_free() signal
the freeing of the transport, tagging it as "dead". In order to do this,
the patch restores the "dead" bit in struct sctp_transport, which was
removed in
commit 47faa1e4c50e ("sctp: remove the dead field of sctp_transport").
Then, in the scenario where the sender thread has released the socket
lock in sctp_wait_for_sndbuf(), the bit is checked again after
re-acquiring the socket lock to detect the deletion. This is done while
holding a reference to the transport to prevent it from being freed in
the process.
If the transport was deleted while the socket lock was relinquished,
sctp_sendmsg_to_asoc() will return -EAGAIN to let userspace retry the
send.
The bug was found by a private syzbot instance (see the error report [1]
and the C reproducer that triggers it [2]).
The PGDAT_RECLAIM_LOCKED bit is used to provide mutual exclusion of node
reclaim for struct pglist_data using a single bit.
It is "locked" with a test_and_set_bit (similarly to a try lock) which
provides full ordering with respect to loads and stores done within
__node_reclaim().
It is "unlocked" with clear_bit(), which does not provide any ordering
with respect to loads and stores done before clearing the bit.
The lack of clear_bit() memory ordering with respect to stores within
__node_reclaim() can cause a subsequent CPU to fail to observe stores from
a prior node reclaim. This is not an issue in practice on TSO (e.g.
x86), but it is an issue on weakly-ordered architectures (e.g. arm64).
Fix this by using clear_bit_unlock rather than clear_bit to clear
PGDAT_RECLAIM_LOCKED with a release memory ordering semantic.
This provides stronger memory ordering (release rather than relaxed).
Link: https://lkml.kernel.org/r/20250312141014.129725-1-mathieu.desnoyers@efficios.com Fixes: d773ed6b856a ("mm: test and set zone reclaim lock before starting reclaim") Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com> Cc: Lorenzo Stoakes <lorenzo.stoakes@oracle.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Alan Stern <stern@rowland.harvard.edu> Cc: Andrea Parri <parri.andrea@gmail.com> Cc: Will Deacon <will@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Boqun Feng <boqun.feng@gmail.com> Cc: Nicholas Piggin <npiggin@gmail.com> Cc: David Howells <dhowells@redhat.com> Cc: Jade Alglave <j.alglave@ucl.ac.uk> Cc: Luc Maranget <luc.maranget@inria.fr> Cc: "Paul E. McKenney" <paulmck@kernel.org> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 38e0edb15bd0 ("mm/apply_to_range: call pte function with lazy
updates") it's been possible for arch_[enter|leave]_lazy_mmu_mode() to be
called without holding a page table lock (for the kernel mappings case),
and therefore it is possible that preemption may occur while in the lazy
mmu mode. The Sparc lazy mmu implementation is not robust to preemption
since it stores the lazy mode state in a per-cpu structure and does not
attempt to manage that state on task switch.
Powerpc had the same issue and fixed it by explicitly disabling preemption
in arch_enter_lazy_mmu_mode() and re-enabling in
arch_leave_lazy_mmu_mode(). See commit b9ef323ea168 ("powerpc/64s:
Disable preemption in hash lazy mmu mode").
Given Sparc's lazy mmu mode is based on powerpc's, let's fix it in the
same way here.
Link: https://lkml.kernel.org/r/20250303141542.3371656-4-ryan.roberts@arm.com Fixes: 38e0edb15bd0 ("mm/apply_to_range: call pte function with lazy updates") Signed-off-by: Ryan Roberts <ryan.roberts@arm.com> Acked-by: David Hildenbrand <david@redhat.com> Acked-by: Andreas Larsson <andreas@gaisler.com> Acked-by: Juergen Gross <jgross@suse.com> Cc: Borislav Betkov <bp@alien8.de> Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Dave Hansen <dave.hansen@linux.intel.com> Cc: David S. Miller <davem@davemloft.net> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Juegren Gross <jgross@suse.com> Cc: Matthew Wilcow (Oracle) <willy@infradead.org> Cc: Thomas Gleinxer <tglx@linutronix.de> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The MT8173 disp-pwm device should have only one compatible string, based
on the following DT validation error:
arch/arm64/boot/dts/mediatek/mt8173-elm.dtb: pwm@1401e000: compatible: 'oneOf' conditional failed, one must be fixed:
['mediatek,mt8173-disp-pwm', 'mediatek,mt6595-disp-pwm'] is too long
'mediatek,mt8173-disp-pwm' is not one of ['mediatek,mt6795-disp-pwm', 'mediatek,mt8167-disp-pwm']
'mediatek,mt8173-disp-pwm' is not one of ['mediatek,mt8186-disp-pwm', 'mediatek,mt8188-disp-pwm', 'mediatek,mt8192-disp-pwm', 'mediatek,mt8195-disp-pwm', 'mediatek,mt8365-disp-pwm']
'mediatek,mt8173-disp-pwm' was expected
'mediatek,mt8183-disp-pwm' was expected
from schema $id: http://devicetree.org/schemas/pwm/mediatek,pwm-disp.yaml#
arch/arm64/boot/dts/mediatek/mt8173-elm.dtb: pwm@1401f000: compatible: 'oneOf' conditional failed, one must be fixed:
['mediatek,mt8173-disp-pwm', 'mediatek,mt6595-disp-pwm'] is too long
'mediatek,mt8173-disp-pwm' is not one of ['mediatek,mt6795-disp-pwm', 'mediatek,mt8167-disp-pwm']
'mediatek,mt8173-disp-pwm' is not one of ['mediatek,mt8186-disp-pwm', 'mediatek,mt8188-disp-pwm', 'mediatek,mt8192-disp-pwm', 'mediatek,mt8195-disp-pwm', 'mediatek,mt8365-disp-pwm']
'mediatek,mt8173-disp-pwm' was expected
'mediatek,mt8183-disp-pwm' was expected
from schema $id: http://devicetree.org/schemas/pwm/mediatek,pwm-disp.yaml#
Drop the extra "mediatek,mt6595-disp-pwm" compatible string.
Fixes: 61aee9342514 ("arm64: dts: mt8173: add MT8173 display PWM driver support node") Cc: YH Huang <yh.huang@mediatek.com> Cc: stable@vger.kernel.org # v4.5+ Signed-off-by: Chen-Yu Tsai <wenst@chromium.org> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Link: https://lore.kernel.org/r/20250108083424.2732375-2-wenst@chromium.org Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In r852_ready(), the dev get from r852_get_dev() need to be checked.
An unstable device should not be ready. A proper implementation can
be found in r852_read_byte(). Add a status check and return 0 when it is
unstable.
In INFTL_findwriteunit(), the return value of inftl_read_oob()
need to be checked. A proper implementation can be
found in INFTL_deleteblock(). The status will be set as
SECTOR_IGNORE to break from the while-loop correctly
if the inftl_read_oob() fails.
Fixes: 8593fbc68b0d ("[MTD] Rework the out of band handling completely") Cc: stable@vger.kernel.org # v2.6+ Signed-off-by: Wentao Liang <vulab@iscas.ac.cn> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The split_sg_phys function was incorrectly setting the offsets of all
scatterlist entries (except the first) to 0. Only the first scatterlist
entry's offset and length needs to be modified to account for the skip.
Setting the rest entries' offsets to 0 could lead to incorrect data
access.
I am using this function in a crypto driver that I'm currently developing
(not yet sent to mailing list). During testing, it was observed that the
output scatterlists (except the first one) contained incorrect garbage
data.
I narrowed this issue down to the call of sg_split(). Upon debugging
inside this function, I found that this resetting of offset is the cause
of the problem, causing the subsequent scatterlists to point to incorrect
memory locations in a page. By removing this code, I am obtaining
expected data in all the split output scatterlists. Thus, this was indeed
causing observable runtime effects!
This patch removes the offending code, ensuring that the page offsets in
the input scatterlist are preserved in the output scatterlist.
Currently, when a lock class is allocated, nr_unused_locks will be
increased by 1, until it gets used: nr_unused_locks will be decreased by
1 in mark_lock(). However, one scenario is missed: a lock class may be
zapped without even being used once. This could result into a situation
that nr_unused_locks != 0 but no unused lock class is active in the
system, and when `cat /proc/lockdep_stats`, a WARN_ON() will
be triggered in a CONFIG_DEBUG_LOCKDEP=y kernel:
The off_gpios could be NULL. Add missing check in the kb3930_probe().
This is similar to the issue fixed in commit b1ba8bcb2d1f
("backlight: hx8357: Fix potential NULL pointer dereference").
This was detected by our static analysis tool.
Cc: stable@vger.kernel.org Fixes: ede6b2d1dfc0 ("mfd: ene-kb3930: Add driver for ENE KB3930 Embedded Controller") Suggested-by: Lee Jones <lee@kernel.org> Signed-off-by: Chenyuan Yang <chenyuan0y@gmail.com> Link: https://lore.kernel.org/r/20250224233736.1919739-1-chenyuan0y@gmail.com Signed-off-by: Lee Jones <lee@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Journal emptiness is not determined by sb->s_sequence == 0 but rather by
sb->s_start == 0 (which is set a few lines above). Furthermore 0 is a
valid transaction ID so the check can spuriously trigger. Remove the
invalid WARN_ON.
CC: stable@vger.kernel.org Signed-off-by: Jan Kara <jack@suse.cz> Reviewed-by: Zhang Yi <yi.zhang@huawei.com> Link: https://patch.msgid.link/20250206094657.20865-3-jack@suse.cz Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The I3C master driver may receive an IBI from a target device that has not
been probed yet. In such cases, the master calls `i3c_master_queue_ibi()`
to queue an IBI work task, leading to "Unable to handle kernel read from
unreadable memory" and resulting in a kernel panic.
Typical IBI handling flow:
1. The I3C master scans target devices and probes their respective drivers.
2. The target device driver calls `i3c_device_request_ibi()` to enable IBI
and assigns `dev->ibi = ibi`.
3. The I3C master receives an IBI from the target device and calls
`i3c_master_queue_ibi()` to queue the target device driver’s IBI
handler task.
However, since target device events are asynchronous to the I3C probe
sequence, step 3 may occur before step 2, causing `dev->ibi` to be `NULL`,
leading to a kernel panic.
Add a NULL pointer check in `i3c_master_queue_ibi()` to prevent accessing
an uninitialized `dev->ibi`, ensuring stability.
create_user_mr() has correct code to count the number of null keys
used to fill in a hole for the memory map. However, fill_indir()
does not follow the same to cap the range up to the 1GB limit
correspondingly. Fill in more null keys for the gaps in between,
so that null keys are correctly populated.
Fixes: 94abbccdf291 ("vdpa/mlx5: Add shared memory registration code") Cc: stable@vger.kernel.org Reported-by: Cong Meng <cong.meng@oracle.com> Signed-off-by: Si-Wei Liu <si-wei.liu@oracle.com> Signed-off-by: Dragos Tatulea <dtatulea@nvidia.com> Acked-by: Eugenio Pérez <eperezma@redhat.com>
Message-Id: <20250220193732.521462-2-dtatulea@nvidia.com> Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Acked-by: Jason Wang <jasowang@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Syzkaller detected a use-after-free issue in ext4_insert_dentry that was
caused by out-of-bounds access due to incorrect splitting in do_split.
BUG: KASAN: use-after-free in ext4_insert_dentry+0x36a/0x6d0 fs/ext4/namei.c:2109
Write of size 251 at addr ffff888074572f14 by task syz-executor335/5847
The following loop is located right above 'if' statement.
for (i = count-1; i >= 0; i--) {
/* is more than half of this entry in 2nd half of the block? */
if (size + map[i].size/2 > blocksize/2)
break;
size += map[i].size;
move++;
}
'i' in this case could go down to -1, in which case sum of active entries
wouldn't exceed half the block size, but previous behaviour would also do
split in half if sum would exceed at the very last block, which in case of
having too many long name files in a single block could lead to
out-of-bounds access and following use-after-free.
Found by Linux Verification Center (linuxtesting.org) with Syzkaller.
Cc: stable@vger.kernel.org Fixes: 5872331b3d91 ("ext4: fix potential negative array index in do_split()") Signed-off-by: Artem Sadovnikov <a.sadovnikov@ispras.ru> Reviewed-by: Jan Kara <jack@suse.cz> Link: https://patch.msgid.link/20250404082804.2567-3-a.sadovnikov@ispras.ru Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case of attempts to compress playback something, for instance,
when audio routing is not set up correctly, the audio DSP is left in
inconsistent state because we are not doing the correct things in
the error path of q6asm_dai_compr_set_params().
So, when routing is not set up and compress playback is attempted
the following errors are present (simplified log):
q6routing routing: Routing not setup for MultiMedia-1 Session
q6asm-dai dais: Stream reg failed ret:-22
q6asm-dai dais: ASoC error (-22): at snd_soc_component_compr_set_params()
on 17300000.remoteproc:glink-edge:apr:service@7:dais
After setting the correct routing the compress playback will always fail:
q6asm-dai dais: cmd = 0x10db3 returned error = 0x9
q6asm-dai dais: DSP returned error[9]
q6asm-dai dais: q6asm_open_write failed
q6asm-dai dais: ASoC error (-22): at snd_soc_component_compr_set_params()
on 17300000.remoteproc:glink-edge:apr:service@7:dais
0x9 here means "Operation is already processed". The CMD_OPEN here was
sent the second time hence DSP responds that it was already done.
Turns out the CMD_CLOSE should be sent after the q6asm_open_write()
succeeded but something failed after that, for instance, routing
setup.
Fix this by slightly reworking the error path in
q6asm_dai_compr_set_params().
Since the new_metric and last_hop_metric variables can reach
the MAX_METRIC(0xffffffff) value, an integer overflow may occur
when multiplying them by 10/9. It can lead to incorrect behavior.
Found by InfoTeCS on behalf of Linux Verification Center
(linuxtesting.org) with SVACE.
Fixes: a8d418d9ac25 ("mac80211: mesh: only switch path when new metric is at least 10% better") Cc: stable@vger.kernel.org Signed-off-by: Ilia Gavrilov <Ilia.Gavrilov@infotecs.ru> Link: https://patch.msgid.link/20250212082124.4078236-1-Ilia.Gavrilov@infotecs.ru Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Implement the workaround for erratum
3.3 RGMII timing may be out of spec when transmit delay is enabled
for the 6320 family, which says:
When transmit delay is enabled via Port register 1 bit 14 = 1, duty
cycle may be out of spec. Under very rare conditions this may cause
the attached device receive CRC errors.
Signed-off-by: Marek Behún <kabel@kernel.org> Cc: <stable@vger.kernel.org> # 5.4.x Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://patch.msgid.link/20250317173250.28780-8-kabel@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a possibility that init_codecs is invoked multiple times during
manipulated payload from video firmware. In such case, if codecs_count
can get incremented to value more than MAX_CODEC_NUM, there can be OOB
access. Reset the count so that it always starts from beginning.
Lift the xshutdown (enable) GPIO 1 ms after enabling the regulators, as
required by the sensor's power-up sequence.
Fixes: d30bb512da3d ("media: Add a driver for the ov7251 camera sensor") Cc: stable@vger.kernel.org Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com> Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes: d30bb512da3d ("media: Add a driver for the ov7251 camera sensor") Cc: stable@vger.kernel.org Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com> Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In v4l2_detect_gtf(), it seems safer to cast the 32-bit image_width
variable to the 64-bit type u64 before multiplying to avoid
a possible overflow. The resulting object code even seems to
look better, at least on x86_64.
Found by Linux Verification Center (linuxtesting.org) with Svace.
If streamzap_callback() receives an urb with any non-critical error
status, i.e. any error code other than -ECONNRESET, -ENOENT or -ESHUTDOWN,
it will try to process IR data, ignoring a possible transfer failure.
Make streamzap_callback() process IR data only when urb->status is 0.
Move processing logic to a separate function to make code cleaner and
more similar to the URB completion handlers in other RC drivers.
Found by Linux Verification Center (linuxtesting.org) with Syzkaller.
Fixes: 19770693c354 ("V4L/DVB: staging/lirc: add lirc_streamzap driver") Cc: stable@vger.kernel.org Signed-off-by: Murad Masimov <m.masimov@mt-integration.ru> Signed-off-by: Sean Young <sean@mess.org> Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixed warning on PM resume as shown below caused due to uninitialized
struct nand_operation that checks chip select field :
WARN_ON(op->cs >= nanddev_ntargets(&chip->base)
The fix uses the higher level nand_reset(chip, chipnr); where chipnr = 0, when
doing PM resume operation in compliance with the controller support for single
die nand chip. Switching from nand_reset_op() to nand_reset() implies more
than just setting the cs field op->cs, it also reconfigures the data interface
(ie. the timings). Tested and confirmed the NAND chip is in sync timing wise
with host after the fix.
Fixes: 97d90da8a886 ("mtd: nand: provide several helpers to do common NAND operations") Cc: stable@vger.kernel.org Signed-off-by: Kamal Dasu <kamal.dasu@broadcom.com> Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In 2020, there's been an unnoticed change which rightfully attempted to
report probe deferrals upon DMA absence by checking the return value of
dma_request_chan_by_mask(). By doing so, it also reported errors which
were simply ignored otherwise, likely on purpose.
This change actually turned a void return into an error code. Hence, not
only the -EPROBE_DEFER error codes but all error codes got reported to
the callers, now failing to probe in the absence of Rx DMA channel,
despite the fact that DMA seems to not be supported natively by many
implementations.
Looking at the history, this change probably led to: ad2775dc3fc5 ("spi: cadence-quadspi: Disable the DAC for Intel LGM SoC") f724c296f2f2 ("spi: cadence-quadspi: fix Direct Access Mode disable for SoCFPGA")
In my case, the AM62A LP SK core octo-SPI node from TI does not
advertise any DMA channel, hinting that there is likely no support for
it, but yet when the support for the am654 compatible was added, DMA
seemed to be used, so just discarding its use with the
CQSPI_DISABLE_DAC_MODE quirk for this compatible does not seem the
correct approach.
Let's get change the return condition back to:
- return a probe deferral error if we get one
- ignore the return value otherwise
The "error" log level was however likely too high for something that is
expected to fail, so let's lower it arbitrarily to the info level.
Fixes: 935da5e5100f ("mtd: spi-nor: cadence-quadspi: Handle probe deferral while requesting DMA channel") Cc: stable@vger.kernel.org Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://patch.msgid.link/20250305200933.2512925-2-miquel.raynal@bootlin.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Qualcomm Kryo 400-series Gold cores have a derivative of an ARM Cortex
A76 in them. Since A76 needs Spectre mitigation via looping then the
Kyro 400-series Gold cores also need Spectre mitigation via looping.
Qualcomm has confirmed that the proper "k" value for Kryo 400-series
Gold cores is 24.
Fixes: 558c303c9734 ("arm64: Mitigate spectre style branch history side channels") Cc: stable@vger.kernel.org Cc: Scott Bauer <sbauer@quicinc.com> Signed-off-by: Douglas Anderson <dianders@chromium.org> Acked-by: Trilok Soni <quic_tsoni@quicinc.com> Link: https://lore.kernel.org/r/20250107120555.v4.1.Ie4ef54abe02e7eb0eee50f830575719bf23bda48@changeid Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The interface specifies the symnum field as an input and output; the
hypervisor sets it to the next sequential symbol's index. xensyms_next()
incrementing the position explicitly (and xensyms_next_sym()
decrementing it to "rewind") is only correct as long as the sequence of
symbol indexes is non-sparse. Use the hypervisor-supplied value instead
to update the position in xensyms_next(), and use the saved incoming
index in xensyms_next_sym().
The smsdvb_module_init() returns without checking the retval from
smscore_register_hotplug().
If the smscore_register_hotplug() failed, the module failed to install,
leaving the smsdvb_debugfs not unregistered.
Fixes: 3f6b87cff66b ("[media] siano: allow showing the complete statistics via debugfs") Cc: stable@vger.kernel.org Signed-off-by: Yuan Can <yuancan@huawei.com> Acked-by: Ricardo Ribalda <ribalda@chromium.org> Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move the v4l2_info() call displaying the video device name after the
device is actually registered.
This fixes a bug where the driver was always displaying "/dev/video0"
since it was reading from the vfd before it was registered.
Fixes: cf7f34777a5b ("media: vim2m: Register video device after setting up internals") Cc: stable@vger.kernel.org Signed-off-by: Matthew Majewski <mattwmajewski@gmail.com> Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
qsize represents size of shared queued between driver and video
firmware. Firmware can modify this value to an invalid large value. In
such situation, empty_space will be bigger than the space actually
available. Since new_wr_idx is not checked, so the following code will
result in an OOB write.
...
qsize = qhdr->q_size
sfr->buf_size is in shared memory and can be modified by malicious user.
OOB write is possible when the size is made higher than actual sfr data
buffer. Cap the size to allocated size for such cases.
The mask to select the test-pattern in register ADV748X_SDP_FRP is
incorrect, it's the lower 3 bits which controls the pattern. The
GENMASK() macro is used incorrectly and the generated mask is 0x0e
instead of 0x07.
The result is that not all test patterns are selectable, and that in
some cases the wrong test pattern is activated. Fix this by correcting
the GENMASK().
A file handle that userspace provides to open_by_handle_at() can
legitimately contain an outdated inode number that has since been reused
for another purpose - that's why the file handle also contains a generation
number.
But if the inode number has been reused for an ea_inode, check_igot_inode()
will notice, __ext4_iget() will go through ext4_error_inode(), and if the
inode was newly created, it will also be marked as bad by iget_failed().
This all happens before the point where the inode generation is checked.
ext4_error_inode() is supposed to only be used on filesystem corruption; it
should not be used when userspace just got unlucky with a stale file
handle. So when this happens, let __ext4_iget() just return an error.
It is invalid for the casefold inode flag to be set without the casefold
superblock feature flag also being set. e2fsck already considers this
case to be invalid and handles it by offering to clear the casefold flag
on the inode. __ext4_iget() also already considered this to be invalid,
sort of, but it only got so far as logging an error message; it didn't
actually reject the inode. Make it reject the inode so that other code
doesn't have to handle this case. This matches what f2fs does.
Note: we could check 's_encoding != NULL' instead of
ext4_has_feature_casefold(). This would make the check robust against
the casefold feature being enabled by userspace writing to the page
cache of the mounted block device. However, it's unsolvable in general
for filesystems to be robust against concurrent writes to the page cache
of the mounted block device. Though this very particular scenario
involving the casefold feature is solvable, we should not pretend that
we can support this model, so let's just check the casefold feature.
tune2fs already forbids enabling casefold on a mounted filesystem.
Classic BPF socket filters with SKB_NET_OFF and SKB_LL_OFF fail to
read when these offsets extend into frags.
This has been observed with iwlwifi and reproduced with tun with
IFF_NAPI_FRAGS. The below straightforward socket filter on UDP port,
applied to a RAW socket, will silently miss matching packets.
This is unexpected behavior. Socket filter programs should be
consistent regardless of environment. Silent misses are
particularly concerning as hard to detect.
Use skb_copy_bits for offsets outside linear, same as done for
non-SKF_(LL|NET) offsets.
Offset is always positive after subtracting the reference threshold
SKB_(LL|NET)_OFF, so is always >= skb_(mac|network)_offset. The sum of
the two is an offset against skb->data, and may be negative, but it
cannot point before skb->head, as skb_(mac|network)_offset would too.
This appears to go back to when frag support was introduced to
sk_run_filter in linux-2.4.4, before the introduction of git.
The amount of code change and 8/16/32 bit duplication are unfortunate.
But any attempt I made to be smarter saved very few LoC while
complicating the code.
A couple of the syscalls which load values (bpf_skb_load_helper_16() and
bpf_skb_load_helper_32()) are using u16/u32 types which are triggering
warnings as they are then converted from big-endian to CPU-endian. Fix
these by making the types __be instead.
Fixes the following sparse warnings:
net/core/filter.c:246:32: warning: cast to restricted __be16
net/core/filter.c:246:32: warning: cast to restricted __be16
net/core/filter.c:246:32: warning: cast to restricted __be16
net/core/filter.c:246:32: warning: cast to restricted __be16
net/core/filter.c:273:32: warning: cast to restricted __be32
net/core/filter.c:273:32: warning: cast to restricted __be32
net/core/filter.c:273:32: warning: cast to restricted __be32
net/core/filter.c:273:32: warning: cast to restricted __be32
net/core/filter.c:273:32: warning: cast to restricted __be32
net/core/filter.c:273:32: warning: cast to restricted __be32
Considering that the driver doesn't enable the used clocks (and also
that clk_get_rate() returns 0 if CONFIG_HAVE_CLK is unset) better check
the return value of clk_get_rate() for being non-zero before dividing by
it.
There were several issues in the function rcar_pwm_set_counter():
- The u64 values period_ns and duty_ns were cast to int on function
call which might loose bits on 32 bit architectures.
Fix: Make parameters to rcar_pwm_set_counter() u64
- The algorithm divided by the result of a division which looses
precision.
Fix: Make use of mul_u64_u64_div_u64()
- The calculated values were just masked to fit the respective register
fields which again might loose bits.
Fix: Explicitly check for overlow
Implement the respective fixes.
A side effect of fixing the 2nd issue is that there is no division by 0
if clk_get_rate() returns 0.
due to the fact that the !CONFIG_HAVE_CLK version of clk_get_rate()
returns zero.
This is presumably just a theoretical problem: COMPILE_TEST overrides
the dependency on RALINK which would select COMMON_CLK. Regardless it's
a good idea to check for the error explicitly to avoid divide-by-zero.
Fixes the following warning:
drivers/pwm/pwm-mediatek.o: warning: objtool: .text: unexpected end of section
The MediaTek PWM IP can sometimes use the 26 MHz source clock to
generate the PWM signal, but the driver currently assumes that we always
use the PWM bus clock to generate the PWM signal.
This commit modifies the PWM driver in order to force the PWM IP to
always use the bus clock as source clock.
I do not have the datasheet of all the MediaTek SoC, so I don't know if
the register to choose the source clock is present in all the SoCs or
only in subset. As a consequence I made this change optional by using a
platform data paremeter to says whether this register is supported or
not. On all the SoCs I don't have the datasheet (MT2712, MT7622, MT7623,
MT7628, MT7629) I kept the behavior to be the same as before this
change.
Function dispc_ovl_setup is not intended to work with the value OMAP_DSS_WB
of the enum parameter plane.
The value of this parameter is initialized in dss_init_overlays and in the
current state of the code it cannot take this value so it's not a real
problem.
For the purposes of defensive coding it wouldn't be superfluous to check
the parameter value, because some functions down the call stack process
this value correctly and some not.
For example, in dispc_ovl_setup_global_alpha it may lead to buffer
overflow.
Add check for this value.
Found by Linux Verification Center (linuxtesting.org) with SVACE static
analysis tool.
In preparation for adding support for MT8195's HDMI reserved
DPI, add calls to clk_prepare_enable() / clk_disable_unprepare()
for the TVD clock: in this particular case, the aforementioned
clock is not (and cannot be) parented to neither pixel or engine
clocks hence it won't get enabled automatically by the clock
framework.
Please note that on all of the currently supported MediaTek
platforms, the TVD clock is always a parent of either pixel or
engine clocks, and this means that the common clock framework
is already enabling this clock before the children.
On such platforms, this commit will only increase the refcount
of the TVD clock without any functional change.
If GPU in reset, destroy_queue return -EIO, pqm_destroy_queue should
delete the queue from process_queue_list and free the resource.
Signed-off-by: Philip Yang <Philip.Yang@amd.com> Reviewed-by: Felix Kuehling <felix.kuehling@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Having an DRM_MODE_CONNECTOR_Unknown connector type is considered bad, and
drm_panel_bridge_add_typed() and derivatives are deprecated for this.
drm_panel_init() won't prevent initializing a panel with a
DRM_MODE_CONNECTOR_Unknown connector type. Luckily there are no in-tree
users doing it, so take this as an opportinuty to document a valid
connector type must be passed.
Returning an error if this rule is violated is not possible because
drm_panel_init() is a void function. Add at least a warning to make any
violations noticeable, especially to non-upstream drivers.
AYANEO 2S uses the same panel and orientation as the AYANEO 2.
Update the AYANEO 2 DMI match to also match AYANEO 2S.
Signed-off-by: Andrew Wyatt <fewtarius@steamfork.org> Signed-off-by: John Edwards <uejji@uejji.net> Tested-by: John Edwards <uejji@uejji.net> Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de> Link: https://patchwork.freedesktop.org/patch/msgid/20250213222455.93533-2-uejji@uejji.net Signed-off-by: Sasha Levin <sashal@kernel.org>
In certain use-cases, a CRTC could switch between two encoders
and because the mode being programmed on the CRTC remains
the same during this switch, the CRTC's mode_changed remains false.
In such cases, the encoder's mode_set also gets skipped.
Skipping mode_set on the encoder for such cases could cause an issue
because even though the same CRTC mode was being used, the encoder
type could have changed like the CRTC could have switched from a
real time encoder to a writeback encoder OR vice-versa.
Allow encoder's mode_set to happen even when connectors changed on a
CRTC and not just when the mode changed.
'hci_register_dev()' calls power up function, which is executed by
kworker - 'hci_power_on()'. This function does access to bluetooth chip
using callbacks from 'hci_ldisc.c', for example 'hci_uart_send_frame()'.
Now 'hci_uart_send_frame()' checks 'HCI_UART_PROTO_READY' bit set, and
if not - it fails. Problem is that 'HCI_UART_PROTO_READY' is set after
'hci_register_dev()', and there is tiny chance that 'hci_power_on()' will
be executed before setting this bit. In that case HCI init logic fails.
Patch moves setting of 'HCI_UART_PROTO_READY' before calling function
'hci_uart_register_dev()'.
Signed-off-by: Arseniy Krasnov <avkrasnov@salutedevices.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When __ftrace_event_enable_disable invokes the class callback to
unregister the event, the return value is not reported up to the
caller, hence leading to event unregister failures being silently
ignored.
This patch assigns the ret variable to the invocation of the
event unregister callback, so that its return value is stored
and reported to the caller, and it raises a warning in case
of error.
With the device instance lock, there is now a possibility of a deadlock:
[ 1.211455] ============================================
[ 1.211571] WARNING: possible recursive locking detected
[ 1.211687] 6.14.0-rc5-01215-g032756b4ca7a-dirty #5 Not tainted
[ 1.211823] --------------------------------------------
[ 1.211936] ip/184 is trying to acquire lock:
[ 1.212032] ffff8881024a4c30 (&dev->lock){+.+.}-{4:4}, at: dev_set_allmulti+0x4e/0xb0
[ 1.212207]
[ 1.212207] but task is already holding lock:
[ 1.212332] ffff8881024a4c30 (&dev->lock){+.+.}-{4:4}, at: dev_open+0x50/0xb0
[ 1.212487]
[ 1.212487] other info that might help us debug this:
[ 1.212626] Possible unsafe locking scenario:
[ 1.212626]
[ 1.212751] CPU0
[ 1.212815] ----
[ 1.212871] lock(&dev->lock);
[ 1.212944] lock(&dev->lock);
[ 1.213016]
[ 1.213016] *** DEADLOCK ***
[ 1.213016]
[ 1.213143] May be due to missing lock nesting notation
[ 1.213143]
[ 1.213294] 3 locks held by ip/184:
[ 1.213371] #0: ffffffff838b53e0 (rtnl_mutex){+.+.}-{4:4}, at: rtnl_nets_lock+0x1b/0xa0
[ 1.213543] #1: ffffffff84e5fc70 (&net->rtnl_mutex){+.+.}-{4:4}, at: rtnl_nets_lock+0x37/0xa0
[ 1.213727] #2: ffff8881024a4c30 (&dev->lock){+.+.}-{4:4}, at: dev_open+0x50/0xb0
[ 1.213895]
[ 1.213895] stack backtrace:
[ 1.213991] CPU: 0 UID: 0 PID: 184 Comm: ip Not tainted 6.14.0-rc5-01215-g032756b4ca7a-dirty #5
[ 1.213993] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Arch Linux 1.16.3-1-1 04/01/2014
[ 1.213994] Call Trace:
[ 1.213995] <TASK>
[ 1.213996] dump_stack_lvl+0x8e/0xd0
[ 1.214000] print_deadlock_bug+0x28b/0x2a0
[ 1.214020] lock_acquire+0xea/0x2a0
[ 1.214027] __mutex_lock+0xbf/0xd40
[ 1.214038] dev_set_allmulti+0x4e/0xb0 # real_dev->flags & IFF_ALLMULTI
[ 1.214040] vlan_dev_open+0xa5/0x170 # ndo_open on vlandev
[ 1.214042] __dev_open+0x145/0x270
[ 1.214046] __dev_change_flags+0xb0/0x1e0
[ 1.214051] netif_change_flags+0x22/0x60 # IFF_UP vlandev
[ 1.214053] dev_change_flags+0x61/0xb0 # for each device in group from dev->vlan_info
[ 1.214055] vlan_device_event+0x766/0x7c0 # on netdevsim0
[ 1.214058] notifier_call_chain+0x78/0x120
[ 1.214062] netif_open+0x6d/0x90
[ 1.214064] dev_open+0x5b/0xb0 # locks netdevsim0
[ 1.214066] bond_enslave+0x64c/0x1230
[ 1.214075] do_set_master+0x175/0x1e0 # on netdevsim0
[ 1.214077] do_setlink+0x516/0x13b0
[ 1.214094] rtnl_newlink+0xaba/0xb80
[ 1.214132] rtnetlink_rcv_msg+0x440/0x490
[ 1.214144] netlink_rcv_skb+0xeb/0x120
[ 1.214150] netlink_unicast+0x1f9/0x320
[ 1.214153] netlink_sendmsg+0x346/0x3f0
[ 1.214157] __sock_sendmsg+0x86/0xb0
[ 1.214160] ____sys_sendmsg+0x1c8/0x220
[ 1.214164] ___sys_sendmsg+0x28f/0x2d0
[ 1.214179] __x64_sys_sendmsg+0xef/0x140
[ 1.214184] do_syscall_64+0xec/0x1d0
[ 1.214190] entry_SYSCALL_64_after_hwframe+0x77/0x7f
[ 1.214191] RIP: 0033:0x7f2d1b4a7e56
Device setup:
netdevsim0 (down)
^ ^
bond netdevsim1.100@netdevsim1 allmulticast=on (down)
When we enslave the lower device (netdevsim0) which has a vlan, we
propagate vlan's allmuti/promisc flags during ndo_open. This causes
(re)locking on of the real_dev.
Propagate allmulti/promisc on flags change, not on the open. There
is a slight semantics change that vlans that are down now propagate
the flags, but this seems unlikely to result in the real issues.
ip link set dev $dev name netdevsim0
ip link set dev netdevsim0 up
ip link add link netdevsim0 name netdevsim0.100 type vlan id 100
ip link set dev netdevsim0.100 allmulticast on down
ip link add name bond1 type bond mode 802.3ad
ip link set dev netdevsim0 down
ip link set dev netdevsim0 master bond1
ip link set dev bond1 up
ip link show
Reported-by: syzbot+b0c03d76056ef6cd12a6@syzkaller.appspotmail.com Closes: https://lore.kernel.org/netdev/Z9CfXjLMKn6VLG5d@mini-arch/T/#m15ba130f53227c883e79fb969687d69d670337a0 Signed-off-by: Stanislav Fomichev <sdf@fomichev.me> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://patch.msgid.link/20250313100657.2287455-1-sdf@fomichev.me Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Once inside 'ext4_xattr_inode_dec_ref_all' we should
ignore xattrs entries past the 'end' entry.
This fixes the following KASAN reported issue:
==================================================================
BUG: KASAN: slab-use-after-free in ext4_xattr_inode_dec_ref_all+0xb8c/0xe90
Read of size 4 at addr ffff888012c120c4 by task repro/2065
The buggy address belongs to the object at ffff888012c12000
which belongs to the cache filp of size 360
The buggy address is located 196 bytes inside of
freed 360-byte region [ffff888012c12000, ffff888012c12168)
Memory state around the buggy address: ffff888012c11f80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ffff888012c12000: fa fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
> ffff888012c12080: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
^ ffff888012c12100: fb fb fb fb fb fb fb fb fb fb fb fb fb fc fc fc ffff888012c12180: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
==================================================================
Add support for Marvell Technology Group Ltd. 88SE9215 SATA 6 Gb/s
controller, which is e.g. used in the DAWICONTROL DC-614e RAID bus
controller and was not automatically recognized before.
Tested with a DAWICONTROL DC-614e RAID bus controller.
------------[ cut here ]------------
UBSAN: array-index-out-of-bounds in fs/f2fs/node.h:381:10
index 18446744073709550692 is out of range for type '__le32[5]' (aka 'unsigned int[5]')
CPU: 0 UID: 0 PID: 5318 Comm: syz.0.0 Not tainted 6.14.0-rc3-syzkaller-00060-g6537cfb395f3 #0
Call Trace:
<TASK>
__dump_stack lib/dump_stack.c:94 [inline]
dump_stack_lvl+0x241/0x360 lib/dump_stack.c:120
ubsan_epilogue lib/ubsan.c:231 [inline]
__ubsan_handle_out_of_bounds+0x121/0x150 lib/ubsan.c:429
get_nid fs/f2fs/node.h:381 [inline]
f2fs_truncate_inode_blocks+0xa5e/0xf60 fs/f2fs/node.c:1181
f2fs_do_truncate_blocks+0x782/0x1030 fs/f2fs/file.c:808
f2fs_truncate_blocks+0x10d/0x300 fs/f2fs/file.c:836
f2fs_truncate+0x417/0x720 fs/f2fs/file.c:886
f2fs_file_write_iter+0x1bdb/0x2550 fs/f2fs/file.c:5093
aio_write+0x56b/0x7c0 fs/aio.c:1633
io_submit_one+0x8a7/0x18a0 fs/aio.c:2052
__do_sys_io_submit fs/aio.c:2111 [inline]
__se_sys_io_submit+0x171/0x2e0 fs/aio.c:2081
do_syscall_x64 arch/x86/entry/common.c:52 [inline]
do_syscall_64+0xf3/0x230 arch/x86/entry/common.c:83
entry_SYSCALL_64_after_hwframe+0x77/0x7f
RIP: 0033:0x7f238798cde9
index 18446744073709550692 (decimal, unsigned long long)
= 0xfffffffffffffc64 (hexadecimal, unsigned long long)
= -924 (decimal, long long)
In f2fs_truncate_inode_blocks(), UBSAN detects that get_nid() tries to
access .i_nid[-924], it means both offset[0] and level should zero.
The possible case should be in f2fs_do_truncate_blocks(), we try to
truncate inode size to zero, however, dn.ofs_in_node is zero and
dn.node_page is not an inode page, so it fails to truncate inode page,
and then pass zeroed free_from to f2fs_truncate_inode_blocks(), result
in this issue.
I guess the reason why dn.node_page is not an inode page could be: there
are multiple nat entries share the same node block address, once the node
block address was reused, f2fs_get_node_page() may load a non-inode block.
Let's add a sanity check for such condition to avoid out-of-bounds access
issue.
The width in dmapctl of the AG is zero, it trigger a divide error when
calculating the control page level in dbAllocAG.
To avoid this issue, add a check for agwidth in dbAllocAG.
Reported-and-tested-by: syzbot+7c808908291a569281a9@syzkaller.appspotmail.com Closes: https://syzkaller.appspot.com/bug?extid=7c808908291a569281a9 Signed-off-by: Edward Adam Davis <eadavis@qq.com> Signed-off-by: Dave Kleikamp <dave.kleikamp@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When calling "ioctl$LOOP_SET_STATUS64", the offset value passed in is 4,
which does not match the mounted loop device, causing the mapping of the
mounted loop device to be invalidated.
When creating the directory and creating the inode of iag in diReadSpecial(),
read the page of fixed disk inode (AIT) in raw mode in read_metapage(), the
metapage data it returns is corrupted, which causes the nlink value of 0 to be
assigned to the iag inode when executing copy_from_dinode(), which ultimately
causes a deadlock when entering diFree().
To avoid this, first check the nlink value of dinode before setting iag inode.
[1]
WARNING: possible recursive locking detected 6.12.0-rc7-syzkaller-00212-g4a5df3796467 #0 Not tainted
--------------------------------------------
syz-executor301/5309 is trying to acquire lock: ffff888044548920 (&(imap->im_aglock[index])){+.+.}-{3:3}, at: diFree+0x37c/0x2fb0 fs/jfs/jfs_imap.c:889
but task is already holding lock: ffff888044548920 (&(imap->im_aglock[index])){+.+.}-{3:3}, at: diAlloc+0x1b6/0x1630
other info that might help us debug this:
Possible unsafe locking scenario:
Reported-by: syzbot+355da3b3a74881008e8f@syzkaller.appspotmail.com Closes: https://syzkaller.appspot.com/bug?extid=355da3b3a74881008e8f Signed-off-by: Edward Adam Davis <eadavis@qq.com> Signed-off-by: Dave Kleikamp <dave.kleikamp@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The JFS filesystem calculates allocation group (AG) size using 1 <<
l2agsize in dbExtendFS(). When l2agsize exceeds 31 (possible with >2TB
aggregates on 32-bit systems), this 32-bit shift operation causes undefined
behavior and improper AG sizing.
On 32-bit architectures:
- Left-shifting 1 by 32+ bits results in 0 due to integer overflow
- This creates invalid AG sizes (0 or garbage values) in
sbi->bmap->db_agsize
- Subsequent block allocations would reference invalid AG structures
- Could lead to:
- Filesystem corruption during extend operations
- Kernel crashes due to invalid memory accesses
- Security vulnerabilities via malformed on-disk structures
Fix by casting to s64 before shifting:
bmp->db_agsize = (s64)1 << l2agsize;
This ensures 64-bit arithmetic even on 32-bit architectures. The cast
matches the data type of db_agsize (s64) and follows similar patterns in
JFS block calculation code.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
The expression "inactags << bmp->db_agl2size" in the function
dbFinalizeBmap() is computed using int operands. Although the
values (inactags and db_agl2size) are derived from filesystem
parameters and are usually small, there is a theoretical risk that
the shift could overflow a 32-bit int if extreme values occur.
According to the C standard, shifting a signed 32-bit int can lead
to undefined behavior if the result exceeds its range. In our
case, an overflow could miscalculate free blocks, potentially
leading to erroneous filesystem accounting.
To ensure the arithmetic is performed in 64-bit space, we cast
"inactags" to s64 before shifting. This defensive fix prevents any
risk of overflow and complies with kernel coding best practices.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
We noticed the kworker in page_pool_release_retry() was waken
up repeatedly and infinitely in production because of the
buggy driver causing the inflight less than 0 and warning
us in page_pool_inflight()[1].
Since the inflight value goes negative, it means we should
not expect the whole page_pool to get back to work normally.
This patch mitigates the adverse effect by not rescheduling
the kworker when detecting the inflight negative in
page_pool_release_retry().
[1]
[Mon Feb 10 20:36:11 2025] ------------[ cut here ]------------
[Mon Feb 10 20:36:11 2025] Negative(-51446) inflight packet-pages
...
[Mon Feb 10 20:36:11 2025] Call Trace:
[Mon Feb 10 20:36:11 2025] page_pool_release_retry+0x23/0x70
[Mon Feb 10 20:36:11 2025] process_one_work+0x1b1/0x370
[Mon Feb 10 20:36:11 2025] worker_thread+0x37/0x3a0
[Mon Feb 10 20:36:11 2025] kthread+0x11a/0x140
[Mon Feb 10 20:36:11 2025] ? process_one_work+0x370/0x370
[Mon Feb 10 20:36:11 2025] ? __kthread_cancel_work+0x40/0x40
[Mon Feb 10 20:36:11 2025] ret_from_fork+0x35/0x40
[Mon Feb 10 20:36:11 2025] ---[ end trace ebffe800f33e7e34 ]---
Note: before this patch, the above calltrace would flood the
dmesg due to repeated reschedule of release_dw kworker.
Fix quirk for CME master keyboards so it not only handles
sysex but also song position pointer, MIDI timing clock, start
and stop messages, and active sensing. All of these can be
output by the CME UF series master keyboards.
Tested with a CME UF6 in a desktop Linux environment as
well as on the Zynthian Raspberry Pi based platform.
quirk_nvidia_hda() forcefully enables HDA controller on all NVIDIA GPUs,
because some buggy BIOSes leave it disabled. However, some dual-GPU
laptops do not have a functional HDA controller in DGPU, and BIOS
disables it on purpose. After quirk_nvidia_hda() reenables this dummy
HDA controller, attempting to probe it fails at azx_first_init(), which
is too late to cancel the probe, as it happens in azx_probe_continue().
The sna_hda_intel driver calls azx_free() and stops the chip, however,
it stays probed, and from the runtime PM point of view, the device
remains active (it was set as active by the PCI subsystem on probe). It
prevents vga_switcheroo from turning off the DGPU, because
pci_create_device_link() syncs power management for video and audio
devices.
Affected devices should be added to driver_denylist to prevent them from
probing early. This patch helps identify such devices by printing a
warning, and also forces the device to the suspended state to allow
vga_switcheroo turn off DGPU.
This function triggered a null pointer dereference if used to search for
a report that isn't implemented on the device. This happened both for
optional and required reports alike.
The same logic was applied to pidff_find_special_field and although
pidff_init_fields should return an error earlier if one of the required
reports is missing, future modifications could change this logic and
resurface this possible null pointer dereference again.
Envelope struct is always initialized, but the envelope itself is
optional as described in USB PID Device class definition 1.0.
5.1.1.1 Type Specific Block Offsets
...
4) Effects that do not use Condition Blocks use 1 Parameter Block and
an *optional* Envelope Block.
Sending out "empty" envelope breaks force feedback on some devices with
games that use SINE effect + offset to emulate constant force effect, as
well as generally breaking Constant/Periodic effects. One of the affected
brands is Moza Racing.
This change prevents the envelope from being sent if it contains all
0 values while keeping the old behavior of only sending it, if it differs
from the old one.
Changes in v6:
- Simplify the checks to make them clearer
- Fix possible null pointer dereference while calling
pidff_needs_set_envelope
Signed-off-by: Tomasz Pakuła <tomasz.pakula.oficjalny@gmail.com> Reviewed-by: Michał Kopeć <michal@nozomi.space> Reviewed-by: Paul Dino Jones <paul@spacefreak18.xyz> Tested-by: Paul Dino Jones <paul@spacefreak18.xyz> Tested-by: Cristóferson Bueno <cbueno81@gmail.com> Tested-by: Pablo Cisneros <patchkez@protonmail.com> Signed-off-by: Jiri Kosina <jkosina@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Software uses 0 as de-facto infinite lenght on Linux FF apis (SDL),
Linux doesn't actually define anythi as of now, while USB PID defines
NULL (0xffff). Most PID devices do not expect a 0-length effect and
can't interpret it as infinite. This change fixes Force Feedback for
most PID compliant devices.
As most games depend on updating the values of already playing infinite
effects, this is crucial to ensure they will actually work.
Previously, users had to rely on third-party software to do this conversion
and make their PID devices usable.
Co-developed-by: Makarenko Oleg <oleg@makarenk.ooo> Signed-off-by: Makarenko Oleg <oleg@makarenk.ooo> Signed-off-by: Tomasz Pakuła <tomasz.pakula.oficjalny@gmail.com> Reviewed-by: Michał Kopeć <michal@nozomi.space> Reviewed-by: Paul Dino Jones <paul@spacefreak18.xyz> Tested-by: Paul Dino Jones <paul@spacefreak18.xyz> Tested-by: Cristóferson Bueno <cbueno81@gmail.com> Tested-by: Pablo Cisneros <patchkez@protonmail.com> Signed-off-by: Jiri Kosina <jkosina@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When a character array without a terminating NUL character has a static
initializer, GCC 15's -Wunterminated-string-initialization will only
warn if the array lacks the "nonstring" attribute[1]. Mark the arrays
with __nonstring to and correctly identify the char array as "not a C
string" and thereby eliminate the warning.
Currently armpmu_add() tries to handle a newly-allocated counter having
a stale associated event, but this should not be possible, and if this
were to happen the current mitigation is insufficient and potentially
expensive. It would be better to warn if we encounter the impossible
case.
Calls to pmu::add() and pmu::del() are serialized by the core perf code,
and armpmu_del() clears the relevant slot in pmu_hw_events::events[]
before clearing the bit in pmu_hw_events::used_mask such that the
counter can be reallocated. Thus when armpmu_add() allocates a counter
index from pmu_hw_events::used_mask, it should not be possible to observe
a stale even in pmu_hw_events::events[] unless either
pmu_hw_events::used_mask or pmu_hw_events::events[] have been corrupted.
If this were to happen, we'd end up with two events with the same
event->hw.idx, which would clash with each other during reprogramming,
deletion, etc, and produce bogus results. Add a WARN_ON_ONCE() for this
case so that we can detect if this ever occurs in practice.
That possiblity aside, there's no need to call arm_pmu::disable(event)
for the new event. The PMU reset code initialises the counter in a
disabled state, and armpmu_del() will disable the counter before it can
be reused. Remove the redundant disable.
Signed-off-by: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Rob Herring (Arm) <robh@kernel.org> Reviewed-by: Anshuman Khandual <anshuman.khandual@arm.com> Tested-by: James Clark <james.clark@linaro.org> Link: https://lore.kernel.org/r/20250218-arm-brbe-v19-v20-2-4e9922fc2e8e@kernel.org Signed-off-by: Will Deacon <will@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When running in a virtual machine, we might see the original hardware CPU
vendor string (i.e. "AuthenticAMD"), but a model and family ID set by the
hypervisor. In case we run on AMD hardware and the hypervisor sets a model
ID < 0x14, the LAHF cpu feature is eliminated from the the list of CPU
capabilities present to circumvent a bug with some BIOSes in conjunction with
AMD K8 processors.
Parsing the flags list from /proc/cpuinfo seems to be happening mostly in
bash scripts and prebuilt Docker containers, as it does not need to have
additionals tools present – even though more reliable ways like using "kcpuid",
which calls the CPUID instruction instead of parsing a list, should be preferred.
Scripts, that use /proc/cpuinfo to determine if the current CPU is
"compliant" with defined microarchitecture levels like x86-64-v2 will falsely
claim the CPU is incapable of modern CPU instructions when "lahf_lm" is missing
in that flags list.
This can prevent some docker containers from starting or build scripts to create
unoptimized binaries.
Admittably, this is more a small inconvenience than a severe bug in the kernel
and the shoddy scripts that rely on parsing /proc/cpuinfo
should be fixed instead.
This patch adds an additional check to see if we're running inside a
virtual machine (X86_FEATURE_HYPERVISOR is present), which, to my
understanding, can't be present on a real K8 processor as it was introduced
only with the later/other Athlon64 models.
Example output with the "lahf_lm" flag missing in the flags list
(should be shown between "hypervisor" and "abm"):
$ cat /proc/cpuinfo
processor : 0
vendor_id : AuthenticAMD
cpu family : 15
model : 6
model name : Common KVM processor
stepping : 1
microcode : 0x1000065
cpu MHz : 2599.998
cache size : 512 KB
physical id : 0
siblings : 1
core id : 0
cpu cores : 1
apicid : 0
initial apicid : 0
fpu : yes
fpu_exception : yes
cpuid level : 13
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca
cmov pat pse36 clflush mmx fxsr sse sse2 syscall nx rdtscp
lm rep_good nopl cpuid extd_apicid tsc_known_freq pni
pclmulqdq ssse3 fma cx16 sse4_1 sse4_2 x2apic movbe popcnt
tsc_deadline_timer aes xsave avx f16c hypervisor abm
3dnowprefetch vmmcall bmi1 avx2 bmi2 xsaveopt
... while kcpuid shows the feature to be present in the CPU:
# kcpuid -d | grep lahf
lahf_lm - LAHF/SAHF available in 64-bit mode
[ mingo: Updated the comment a bit, incorporated Boris's review feedback. ]
Loosen the permission check on forced umount to allow users holding
CAP_SYS_ADMIN privileges in namespaces that are privileged with respect
to the userns that originally mounted the filesystem.
The value of 'ff' is irrelevant, any address will be matched
as long as the other octets are the same.
This is because of too-early register clobbering:
ymm7 is reloaded with new packet data (pkt[9]) but it still holds data
of an earlier load that wasn't processed yet.
The existing tests in nft_concat_range.sh selftests do exercise this code
path, but do not trigger incorrect matching due to the network prefix
limitation.
Ensure we have enough data in linear buffer from skb before accessing
initial bytes. This prevents potential out-of-bounds accesses
when processing short packets.
When ppp_sync_txmung receives an incoming package with an empty
payload:
(remote) gef➤ p *(struct pppoe_hdr *) (skb->head + skb->network_header)
$18 = {
type = 0x1,
ver = 0x1,
code = 0x0,
sid = 0x2,
length = 0x0,
tag = 0xffff8880371cdb96
}
from the skb struct (trimmed)
tail = 0x16,
end = 0x140,
head = 0xffff88803346f400 "4",
data = 0xffff88803346f416 ":\377",
truesize = 0x380,
len = 0x0,
data_len = 0x0,
mac_len = 0xe,
hdr_len = 0x0,
The newly element to be added to the list is the first argument of
list_add_tail. This fix is missing dcfad4ab4d67 ("nvmet-fcloop: swap
the list_add_tail arguments").
Fixes: 437c0b824dbd ("nvme-fcloop: add target to host LS request support") Signed-off-by: Daniel Wagner <wagi@kernel.org> Reviewed-by: Hannes Reinecke <hare@suse.de> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
The function pdc20621_prog_dimm0() calls the function pdc20621_i2c_read()
but does not handle the error if the read fails. This could lead to
process with invalid data. A proper implementation can be found in
/source/drivers/ata/sata_sx4.c, pdc20621_prog_dimm_global(). As mentioned
in its commit: bb44e154e25125bef31fa956785e90fccd24610b, the variable spd0
might be used uninitialized when pdc20621_i2c_read() fails.
Add error handling to pdc20621_i2c_read(). If a read operation fails,
an error message is logged via dev_err(), and return a negative error
code.
Add error handling to pdc20621_prog_dimm0() in pdc20621_dimm_init(), and
return a negative error code if pdc20621_prog_dimm0() fails.
Fixes: 4447d3515616 ("libata: convert the remaining SATA drivers to new init model") Signed-off-by: Wentao Liang <vulab@iscas.ac.cn> Reviewed-by: Niklas Cassel <cassel@kernel.org> Signed-off-by: Damien Le Moal <dlemoal@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
syzbot discovered that it can disconnect a TLS socket and then
run into all sort of unexpected corner cases. I have a vague
recollection of Eric pointing this out to us a long time ago.
Supporting disconnect is really hard, for one thing if offload
is enabled we'd need to wait for all packets to be _acked_.
Disconnect is not commonly used, disallow it.
The immediate problem syzbot run into is the warning in the strp,
but that's just the easiest bug to trigger:
In case the backlog transmit queue for system-importance messages is overloaded,
tipc_link_xmit() returns -ENOBUFS but the skb list is not purged. This leads to
memory leak and failure when a skb is allocated.
This commit fixes this issue by purging the skb list before tipc_link_xmit()
returns.
Fixes: 365ad353c256 ("tipc: reduce risk of user starvation during link congestion") Signed-off-by: Tung Nguyen <tung.quang.nguyen@est.tech> Link: https://patch.msgid.link/20250403092431.514063-1-tung.quang.nguyen@est.tech Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
devm_ioremap() returns NULL on error. Currently, pxa_ata_probe() does
not check for this case, which can result in a NULL pointer dereference.
Add NULL check after devm_ioremap() to prevent this issue.
Fixes: 2dc6c6f15da9 ("[ARM] pata_pxa: DMA-capable PATA driver") Signed-off-by: Henry Martin <bsdhenrymartin@gmail.com> Signed-off-by: Damien Le Moal <dlemoal@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / thirdparty / kernel / stable.git / log
