When inetdev_valid_mtu fails, cork->opt should be freed if it is
allocated in ip_setup_cork. Otherwise there could be a memleak.
Fixes: 501a90c94510 ("inet: protect against too small mtu values.") Signed-off-by: Zhipeng Lu <alexious@zju.edu.cn> Reviewed-by: Eric Dumazet <edumazet@google.com> Link: https://lore.kernel.org/r/20240129091017.2938835-1-alexious@zju.edu.cn Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
- Disallow families other than NFPROTO_{IPV4,IPV6,INET}.
- Disallow layer 4 protocol with no ports, since destination port is a
mandatory attribute for this object.
The original idea of the delay_time check was to not apply multicast
snooping too early when an MLD querier appears. And to instead wait at
least for MLD reports to arrive before switching from flooding to group
based, MLD snooped forwarding, to avoid temporary packet loss.
However in a batman-adv mesh network it was noticed that after 248 days of
uptime 32bit MIPS based devices would start to signal that they had
stopped applying multicast snooping due to missing queriers - even though
they were the elected querier and still sending MLD queries themselves.
While time_is_before_jiffies() generally is safe against jiffies
wrap-arounds, like the code comments in jiffies.h explain, it won't
be able to track a difference larger than ULONG_MAX/2. With a 32bit
large jiffies and one jiffies tick every 10ms (CONFIG_HZ=100) on these MIPS
devices running OpenWrt this would result in a difference larger than
ULONG_MAX/2 after 248 (= 2^32/100/60/60/24/2) days and
time_is_before_jiffies() would then start to return false instead of
true. Leading to multicast snooping not being applied to multicast
packets anymore.
Fix this issue by using a proper timer_list object which won't have this
ULONG_MAX/2 difference limitation.
Fixes: b00589af3b04 ("bridge: disable snooping if there is no querier") Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue> Acked-by: Nikolay Aleksandrov <razor@blackwall.org> Link: https://lore.kernel.org/r/20240127175033.9640-1-linus.luessing@c0d3.blue Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
syzbot reported an interesting trace [1] caused by a stale sk->sk_wq
pointer in a closed llc socket.
In commit ff7b11aa481f ("net: socket: set sock->sk to NULL after
calling proto_ops::release()") Eric Biggers hinted that some protocols
are missing a sock_orphan(), we need to perform a full audit.
In net-next, I plan to clear sock->sk from sock_orphan() and
amend Eric patch to add a warning.
[1]
BUG: KASAN: slab-use-after-free in list_empty include/linux/list.h:373 [inline]
BUG: KASAN: slab-use-after-free in waitqueue_active include/linux/wait.h:127 [inline]
BUG: KASAN: slab-use-after-free in sock_def_write_space_wfree net/core/sock.c:3384 [inline]
BUG: KASAN: slab-use-after-free in sock_wfree+0x9a8/0x9d0 net/core/sock.c:2468
Read of size 8 at addr ffff88802f4fc880 by task ksoftirqd/1/27
The buggy address belongs to the object at ffff88802f4fc800
which belongs to the cache sock_inode_cache of size 1408
The buggy address is located 128 bytes inside of
freed 1408-byte region [ffff88802f4fc800, ffff88802f4fcd80)
Memory state around the buggy address: ffff88802f4fc780: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc ffff88802f4fc800: fa fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
>ffff88802f4fc880: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
^ ffff88802f4fc900: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ffff88802f4fc980: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
Fixes: 43815482370c ("net: sock_def_readable() and friends RCU conversion") Reported-and-tested-by: syzbot+32b89eaa102b372ff76d@syzkaller.appspotmail.com Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Eric Biggers <ebiggers@google.com> Cc: Kuniyuki Iwashima <kuniyu@amazon.com> Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com> Link: https://lore.kernel.org/r/20240126165532.3396702-1-edumazet@google.com Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
On a parisc64 kernel I sometimes notice this kernel warning:
Kernel unaligned access to 0x40ff8814 at ndisc_send_skb+0xc0/0x4d8
The address 0x40ff8814 points to the in6addr_linklocal_allrouters
variable and the warning simply means that some ipv6 function tries to
read a 64-bit word directly from the not-64-bit aligned
in6addr_linklocal_allrouters variable.
Unaligned accesses are non-critical as the architecture or exception
handlers usually will fix it up at runtime. Nevertheless it may trigger
a performance penality for some architectures. For details read the
"unaligned-memory-access" kernel documentation.
The patch below ensures that the ipv6 loopback and router addresses will
always be naturally aligned. This prevents the unaligned accesses for
all architectures.
Signed-off-by: Helge Deller <deller@gmx.de> Fixes: 034dfc5df99eb ("ipv6: export in6addr_loopback to modules") Acked-by: Paolo Abeni <pabeni@redhat.com> Link: https://lore.kernel.org/r/ZbNuFM1bFqoH-UoY@p100 Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
All error handling paths, except this one, go to 'out' where
release_swfw_sync() is called.
This call balances the acquire_swfw_sync() call done at the beginning of
the function.
Branch to the error handling path in order to correctly release some
resources in case of error.
Fixes: ae14a1d8e104 ("ixgbe: Fix IOSF SB access issues") Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Reviewed-by: Simon Horman <horms@kernel.org> Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently ixgbe driver is notified of overheating events
via internal IXGBE_ERR_OVERTEMP error code.
Change the approach for handle_lasi() to use freshly introduced
is_overtemp function parameter which set when such event occurs.
Change check_overtemp() to bool and return true if overtemp
event occurs.
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com> Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Reviewed-by: Simon Horman <horms@kernel.org> Tested-by: Sunitha Mekala <sunithax.d.mekala@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fixes: 93ab6cc69162 ("tcp: implement mmap() for zero copy receive") Link: https://lore.kernel.org/netdev/5106a58e-04da-372a-b836-9d3d0bd2507b@huawei.com/T/ Reported-and-bisected-by: ZhangPeng <zhangpeng362@huawei.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Arjun Roy <arjunroy@google.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: linux-mm@vger.kernel.org Cc: Andrew Morton <akpm@linux-foundation.org> Cc: linux-fsdevel@vger.kernel.org Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: 8d975c15c0cd ("ip6_tunnel: make sure to pull inner header in __ip6_tnl_rcv()") Signed-off-by: Sasha Levin <sashal@kernel.org>
The gro.sh test-case relay on the gro_flush_timeout to ensure
that all the segments belonging to any given batch are properly
aggregated.
The other end, the sender is a user-space program transmitting
each packet with a separate write syscall. A busy host and/or
stracing the sender program can make the relevant segments reach
the GRO engine after the flush timeout triggers.
Give the GRO flush timeout more slack, to avoid sporadic self-tests
failures.
Fixes: 9af771d2ec04 ("selftests/net: allow GRO coalesce test on veth") Signed-off-by: Paolo Abeni <pabeni@redhat.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Tested-by: Eric Dumazet <edumazet@google.com> Link: https://lore.kernel.org/r/bffec2beab3a5672dd13ecabe4fad81d2155b367.1706206101.git.pabeni@redhat.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Inside scsi_eh_wakeup(), scsi_host_busy() is called & checked with host
lock every time for deciding if error handler kthread needs to be waken up.
This can be too heavy in case of recovery, such as:
- N hardware queues
- queue depth is M for each hardware queue
- each scsi_host_busy() iterates over (N * M) tag/requests
If recovery is triggered in case that all requests are in-flight, each
scsi_eh_wakeup() is strictly serialized, when scsi_eh_wakeup() is called
for the last in-flight request, scsi_host_busy() has been run for (N * M -
1) times, and request has been iterated for (N*M - 1) * (N * M) times.
If both N and M are big enough, hard lockup can be triggered on acquiring
host lock, and it is observed on mpi3mr(128 hw queues, queue depth 8169).
Fix the issue by calling scsi_host_busy() outside the host lock. We don't
need the host lock for getting busy count because host the lock never
covers that.
[mkp: Drop unnecessary 'busy' variables pointed out by Bart]
Cc: Ewan Milne <emilne@redhat.com> Fixes: 6eb045e092ef ("scsi: core: avoid host-wide host_busy counter for scsi_mq") Signed-off-by: Ming Lei <ming.lei@redhat.com> Link: https://lore.kernel.org/r/20240112070000.4161982-1-ming.lei@redhat.com Reviewed-by: Ewan D. Milne <emilne@redhat.com> Reviewed-by: Sathya Prakash Veerichetty <safhya.prakash@broadcom.com> Tested-by: Sathya Prakash Veerichetty <safhya.prakash@broadcom.com> Reviewed-by: Bart Van Assche <bvanassche@acm.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Some pending include file cleanups produced this error:
In file included from include/linux/kernel.h:27,
from drivers/gpu/ipu-v3/ipu-dp.c:7:
include/drm/drm_color_mgmt.h: In function 'drm_color_lut_extract':
include/drm/drm_color_mgmt.h:45:46: error: implicit declaration of function 'mul_u32_u32' [-Werror=implicit-function-declaration]
45 | return DIV_ROUND_CLOSEST_ULL(mul_u32_u32(user_input, (1 << bit_precision) - 1),
| ^~~~~~~~~~~
Replace rcu_dereference() with rcu_access_pointer() since we hold
the lock here (and aren't in an RCU critical section).
Fixes: 32af9a9e1069 ("wifi: cfg80211: free beacon_ies when overridden from hidden BSS") Reported-and-tested-by: syzbot+864a269c27ee06b58374@syzkaller.appspotmail.com Signed-off-by: Edward Adam Davis <eadavis@qq.com> Link: https://msgid.link/tencent_BF8F0DF0258C8DBF124CDDE4DD8D992DCF07@qq.com Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Thomas reported that commit 652ffc2104ec ("perf/core: Fix narrow
startup race when creating the perf nr_addr_filters sysfs file") made
the entire attribute group vanish, instead of only the nr_addr_filters
attribute.
Additionally a stray return.
Insufficient coffee was involved with both writing and merging the
patch.
Fixes: 652ffc2104ec ("perf/core: Fix narrow startup race when creating the perf nr_addr_filters sysfs file") Reported-by: Thomas Richter <tmricht@linux.ibm.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Tested-by: Thomas Richter <tmricht@linux.ibm.com> Link: https://lkml.kernel.org/r/20231122100756.GP8262@noisy.programming.kicks-ass.net Signed-off-by: Sasha Levin <sashal@kernel.org>
Range interval [start, last] is ordered by rb_tree, rb_prev, rb_next
return value still needs NULL check, thus modified from "node" to "rb_node".
Fixes the below:
drivers/gpu/drm/amd/amdgpu/../amdkfd/kfd_svm.c:2691 svm_range_get_range_boundaries() warn: can 'node' even be NULL?
Suggested-by: Philip Yang <Philip.Yang@amd.com> Cc: Felix Kuehling <Felix.Kuehling@amd.com> Cc: Christian König <christian.koenig@amd.com> Cc: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com> Reviewed-by: Felix Kuehling <felix.kuehling@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In function 'amdgpu_device_need_post(struct amdgpu_device *adev)' -
'adev->pm.fw' may not be released before return.
Using the function release_firmware() to release adev->pm.fw.
Thus fixing the below:
drivers/gpu/drm/amd/amdgpu/amdgpu_device.c:1571 amdgpu_device_need_post() warn: 'adev->pm.fw' from request_firmware() not released on lines: 1554.
Cc: Monk Liu <Monk.Liu@amd.com> Cc: Christian König <christian.koenig@amd.com> Cc: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com> Suggested-by: Lijo Lazar <lijo.lazar@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In 'struct phm_ppm_table *ptr' allocation using kzalloc, an incorrect
structure type is passed to sizeof() in kzalloc, larger structure types
were used, thus using correct type 'struct phm_ppm_table' fixes the
below:
drivers/gpu/drm/amd/amdgpu/../pm/powerplay/hwmgr/process_pptables_v1_0.c:203 get_platform_power_management_table() warn: struct type mismatch 'phm_ppm_table vs _ATOM_Tonga_PPM_Table'
Cc: Eric Huang <JinHuiEric.Huang@amd.com> Cc: Christian König <christian.koenig@amd.com> Cc: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com> Acked-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In blk_mq_mark_tag_wait(), __add_wait_queue() may be re-ordered
with the following blk_mq_get_driver_tag() in case of getting driver
tag failure.
Then in __sbitmap_queue_wake_up(), waitqueue_active() may not observe
the added waiter in blk_mq_mark_tag_wait() and wake up nothing, meantime
blk_mq_mark_tag_wait() can't get driver tag successfully.
This issue can be reproduced by running the following test in loop, and
fio hang can be observed in < 30min when running it on my test VM
in laptop.
"
drivers/net/virtio_net.c: In function ‘init_vqs’:
drivers/net/virtio_net.c:4551:48: warning: ‘%d’ directive writing between 1 and 11 bytes into a region of size 10 [-Wformat-overflow=]
4551 | sprintf(vi->rq[i].name, "input.%d", i);
| ^~
In function ‘virtnet_find_vqs’,
inlined from ‘init_vqs’ at drivers/net/virtio_net.c:4645:8:
drivers/net/virtio_net.c:4551:41: note: directive argument in the range [-2147483643, 65534]
4551 | sprintf(vi->rq[i].name, "input.%d", i);
| ^~~~~~~~~~
drivers/net/virtio_net.c:4551:17: note: ‘sprintf’ output between 8 and 18 bytes into a destination of size 16
4551 | sprintf(vi->rq[i].name, "input.%d", i);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/virtio_net.c: In function ‘init_vqs’:
drivers/net/virtio_net.c:4552:49: warning: ‘%d’ directive writing between 1 and 11 bytes into a region of size 9 [-Wformat-overflow=]
4552 | sprintf(vi->sq[i].name, "output.%d", i);
| ^~
In function ‘virtnet_find_vqs’,
inlined from ‘init_vqs’ at drivers/net/virtio_net.c:4645:8:
drivers/net/virtio_net.c:4552:41: note: directive argument in the range [-2147483643, 65534]
4552 | sprintf(vi->sq[i].name, "output.%d", i);
| ^~~~~~~~~~~
drivers/net/virtio_net.c:4552:17: note: ‘sprintf’ output between 9 and 19 bytes into a destination of size 16
4552 | sprintf(vi->sq[i].name, "output.%d", i);
I believe this cannot really lead to a deadlock in practice, because
svm_range_evict_svm_bo_worker only takes the mmap_read_lock if the BO
refcount is non-0. That means it's impossible that svm_range_bo_release
is running concurrently. However, there is no good way to annotate this.
To avoid the problem, take a BO reference in
svm_range_schedule_evict_svm_bo instead of in the worker. That way it's
impossible for a BO to get freed while eviction work is pending and the
cancel_work_sync call in svm_range_bo_release can be eliminated.
v2: Use svm_bo_ref_unless_zero and explained why that's safe. Also
removed redundant checks that are already done in
amdkfd_fence_enable_signaling.
Signed-off-by: Felix Kuehling <felix.kuehling@amd.com> Reviewed-by: Philip Yang <philip.yang@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
uniq() will write one command name over another causing the overwritten
string to be leaked. Fix by doing a pass that removes duplicates and a
second that removes the holes.
Signed-off-by: Ian Rogers <irogers@google.com> Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Chenyuan Mi <cymi20@fudan.edu.cn> Cc: Ingo Molnar <mingo@redhat.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Link: https://lore.kernel.org/r/20231208000515.1693746-1-irogers@google.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When a device with AER detects an error, it logs error information in its
own AER Error Status registers. It may send an Error Message to the Root
Port (RCEC in the case of an RCiEP), which logs the fact that an Error
Message was received (Root Error Status) and the Requester ID of the
message source (Error Source Identification).
aer_print_port_info() prints the Requester ID from the Root Port Error
Source in the usual Linux "bb:dd.f" format, but when find_source_device()
finds no error details in the hierarchy below the Root Port, it printed the
raw Requester ID without decoding it.
Decode the Requester ID in the usual Linux format so it matches other
messages.
Sample message changes:
- pcieport 0000:00:1c.5: AER: Correctable error received: 0000:00:1c.5
- pcieport 0000:00:1c.5: AER: can't find device of ID00e5
+ pcieport 0000:00:1c.5: AER: Correctable error message received from 0000:00:1c.5
+ pcieport 0000:00:1c.5: AER: found no error details for 0000:00:1c.5
Unlike the lower rates, the PCIe 64GT/s Data Rate uses 1b/1b encoding, not
128b/130b (PCIe r6.1 sec 1.2, Table 1-1). Correct the PCIE_SPEED2MBS_ENC()
calculation to reflect that.
Handling of S_ISGID is usually done by inode_init_owner() in all other
filesystems, but kernfs doesn't use that function. In kernfs, struct
kernfs_node is the primary data structure, and struct inode is only
created from it on demand. Therefore, inode_init_owner() can't be
used and we need to imitate its behavior.
S_ISGID support is useful for the cgroup filesystem; it allows
subtrees managed by an unprivileged process to retain a certain owner
gid, which then enables sharing access to the subtree with another
unprivileged process.
The capability CAP_CHECKPOINT_RESTORE was introduced to allow non-root
users to checkpoint and restore processes as non-root with CRIU.
This change extends CAP_CHECKPOINT_RESTORE to enable the CRIU option
'--shell-job' as non-root. CRIU's man-page describes the '--shell-job'
option like this:
Allow one to dump shell jobs. This implies the restored task will
inherit session and process group ID from the criu itself. This option
also allows to migrate a single external tty connection, to migrate
applications like top.
TIOCSLCKTRMIOS can only be done if the process has CAP_SYS_ADMIN and
this change extends it to CAP_SYS_ADMIN or CAP_CHECKPOINT_RESTORE.
With this change it is possible to checkpoint and restore processes
which have a tty connection as non-root if CAP_CHECKPOINT_RESTORE is
set.
Acked-by: Christian Brauner <brauner@kernel.org> Signed-off-by: Adrian Reber <areber@redhat.com> Acked-by: Andrei Vagin <avagin@gmail.com> Link: https://lore.kernel.org/r/20231208143656.1019-1-areber@redhat.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
DEFINED only considers symbols, not section names. Hence, replace the
check for .got.plt with the _GLOBAL_OFFSET_TABLE_ symbol and remove other
(non-essential) asserts.
Since commit d927ef5004ef ("perf cs-etm: Add exception level consistency
check"), the exception that was added to Perf will be triggered unless
the following bugfix from OpenCSD is present:
- _Version 1.2.1_:
- __Bugfix__:
ETM4x / ETE - output of context elements to client can in some
circumstances be delayed until after subsequent atoms have been
processed leading to incorrect memory decode access via the client
callbacks. Fixed to flush context elements immediately they are
committed.
Rather than remove the assert and silently fail, just increase the
minimum version requirement to avoid hard to debug issues and
regressions.
Reviewed-by: Ian Rogers <irogers@google.com> Signed-off-by: James Clark <james.clark@arm.com> Tested-by: Leo Yan <leo.yan@linaro.org> Cc: John Garry <john.g.garry@oracle.com> Cc: Mike Leach <mike.leach@linaro.org> Cc: Will Deacon <will@kernel.org> Cc: linux-arm-kernel@lists.infradead.org Link: https://lore.kernel.org/r/20230901133716.677499-1-james.clark@arm.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
A PCI device hot removal may occur while stdev->cdev is held open. The call
to stdev_release() then happens during close or exit, at a point way past
switchtec_pci_remove(). Otherwise the last ref would vanish with the
trailing put_device(), just before return.
At that later point in time, the devm cleanup has already removed the
stdev->mmio_mrpc mapping. Also, the stdev->pdev reference was not a counted
one. Therefore, in DMA mode, the iowrite32() in stdev_release() will cause
a fatal page fault, and the subsequent dma_free_coherent(), if reached,
would pass a stale &stdev->pdev->dev pointer.
Fix by moving MRPC DMA shutdown into switchtec_pci_remove(), after
stdev_kill(). Counting the stdev->pdev ref is now optional, but may prevent
future accidents.
Reproducible via the script at
https://lore.kernel.org/r/20231113212150.96410-1-dns@arista.com
By running a Van Gogh device (Steam Deck), the following message
was noticed in the kernel log:
pci 0000:04:00.3: PCI class overridden (0x0c03fe -> 0x0c03fe) so dwc3 driver can claim this instead of xhci
Effectively this means the quirk executed but changed nothing, since the
class of this device was already the proper one (likely adjusted by newer
firmware versions).
When arm_mhuv2 working with the data protocol transfer mode.
We have split one mhu into two channels, and every channel
include four channel windows, the two channels share
one gic spi interrupt.
There is a problem with the sending scenario.
The first channel will take up 0-3 channel windows, and the second
channel take up 4-7 channel windows. When the first channel send the
data, and the receiver will clear all the four channels status.
Although we only enabled the interrupt on the last channel window with
register CH_INT_EN,the register CHCOMB_INT_ST0 will be 0xf, not be 0x8.
Currently we just clear the last channel windows int status with the
data proctol mode.So after that,the CHCOMB_INT_ST0 status will be 0x7,
not be the 0x0.
Then the second channel send the data, the receiver read the
data, clear all the four channel windows status, trigger the sender
interrupt. But currently the CHCOMB_INT_ST0 register will be 0xf7,
get_irq_chan_comb function will always return the first channel.
So this patch clear all channel windows int status to avoid this interrupt
confusion.
DO NOT access the underlying struct page of an sg table exported
by DMA-buf in dmabuf_imp_to_refs(), this is not allowed.
Please see drivers/dma-buf/dma-buf.c:mangle_sg_table() for details.
Fortunately, here (for special Xen device) we can avoid using
pages and calculate gfns directly from dma addresses provided by
the sg table.
Suggested-by: Daniel Vetter <daniel@ffwll.ch> Signed-off-by: Oleksandr Tyshchenko <oleksandr_tyshchenko@epam.com> Acked-by: Christian König <christian.koenig@amd.com> Reviewed-by: Stefano Stabellini <sstabellini@kernel.org> Acked-by: Daniel Vetter <daniel@ffwll.ch> Link: https://lore.kernel.org/r/20240107103426.2038075-1-olekstysh@gmail.com Signed-off-by: Juergen Gross <jgross@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
As per the Cadence IP document fixed the I2C clock divider value limit from
16 bits instead of 10 bits. Without this change setting up the I2C clock to
low frequencies will not work as the prescaler value might be greater than
10 bit number.
I3C clock divider value is 10 bits only. Updating the macro names for both.
In 'basic' time-travel mode (without =inf-cpu or =ext), we
still get timer interrupts. These can happen at arbitrary
points in time, i.e. while in timer_read(), which pushes
time forward just a little bit. Then, if we happen to get
the interrupt after calculating the new time to push to,
but before actually finishing that, the interrupt will set
the time to a value that's incompatible with the forward,
and we'll crash because time goes backwards when we do the
forwarding.
Fix this by reading the time_travel_time, calculating the
adjustment, and doing the adjustment all with interrupts
disabled.
Reported-by: Vincent Whitchurch <Vincent.Whitchurch@axis.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Richard Weinberger <richard@nod.at> Signed-off-by: Sasha Levin <sashal@kernel.org>
With clang's kernel control flow integrity (kCFI, CONFIG_CFI_CLANG),
indirect call targets are validated against the expected function
pointer prototype to make sure the call target is valid to help mitigate
ROP attacks. If they are not identical, there is a failure at run time,
which manifests as either a kernel panic or thread getting killed. A
warning in clang aims to catch these at compile time, which reveals:
arch/um/drivers/net_kern.c:353:21: warning: incompatible function pointer types initializing 'netdev_tx_t (*)(struct sk_buff *, struct net_device *)' (aka 'enum netdev_tx (*)(struct sk_buff *, struct net_device *)') with an expression of type 'int (struct sk_buff *, struct net_device *)' [-Wincompatible-function-pointer-types-strict]
353 | .ndo_start_xmit = uml_net_start_xmit,
| ^~~~~~~~~~~~~~~~~~
1 warning generated.
->ndo_start_xmit() in 'struct net_device_ops' expects a return type of
'netdev_tx_t', not 'int'. Adjust the return type of uml_net_start_xmit()
to match the prototype's to resolve the warning. While UML does not
currently implement support for kCFI, it could in the future, which
means this warning becomes a fatal CFI failure at run time.
Reported-by: kernel test robot <lkp@intel.com> Closes: https://lore.kernel.org/oe-kbuild-all/202310031340.v1vPh207-lkp@intel.com/ Acked-by: Anton Ivanov <anton.ivanov@cambridgegreys.com> Signed-off-by: Nathan Chancellor <nathan@kernel.org> Signed-off-by: Richard Weinberger <richard@nod.at> Signed-off-by: Sasha Levin <sashal@kernel.org>
The threads allocated inside the kernel have only a single page of
stack. Unfortunately, the vfprintf function in standard glibc may use
too much stack-space, overflowing it.
To make os_info safe to be used by helper threads, use the kernel
vscnprintf function into a smallish buffer and write out the information
to stderr.
Signed-off-by: Benjamin Berg <benjamin@sipsolutions.net> Signed-off-by: Richard Weinberger <richard@nod.at> Signed-off-by: Sasha Levin <sashal@kernel.org>
When OMTP headset plugin the headset jack of CX8070 and SN6160 sound cards,
the headset type detection circuit will recognize the headset type as CTIA.
At this point, plugout and plugin the headset will get the correct headset
type as OMTP.
The reason for the failure of headset type recognition is that the sound
card creation will enable the VREF voltage of the headset mic, which
interferes with the headset type automatic detection circuit. Plugout and
plugin the headset will restart the headset detection and get the correct
headset type.
The patch is disable the VREF voltage when the headset is not present, and
will enable the VREF voltage when the headset is present.
Return value of container_of(...) can't be null, so null check is not
required for 'fence'. Hence drop its NULL check.
Fixes the below:
drivers/gpu/drm/amd/amdgpu/amdgpu_amdkfd_fence.c:93 to_amdgpu_amdkfd_fence() warn: can 'fence' even be NULL?
Cc: Felix Kuehling <Felix.Kuehling@amd.com> Cc: Christian König <christian.koenig@amd.com> Cc: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com> Reviewed-by: Felix Kuehling <felix.kuehling@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Change the rules for amdgpu_sync_resv to let KFD synchronize with VM
fences on page table reservations. This fixes intermittent memory
corruption after evictions when using amdgpu_vm_handle_moved to update
page tables for VM mappings managed through render nodes.
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
To be compatible with SCU firmware based on 1.15 a different clock
routing for LVDS is needed.
Signed-off-by: Oliver F. Brown <oliver.brown@oss.nxp.com> Signed-off-by: Ranjani Vaidyanathan <ranjani.vaidyanathan@nxp.com> Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com> Reviewed-by: Abel Vesa <abel.vesa@linaro.org> Link: https://lore.kernel.org/r/20231218122407.2757175-1-alexander.stein@ew.tq-group.com/ Signed-off-by: Abel Vesa <abel.vesa@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In cases where imx_clk_is_resource_owned() returns false, the code path
does not handle the failure gracefully, potentially leading to a memory
leak. This fix ensures proper cleanup by freeing the allocated memory
for 'clk_node' before returning.
WDTCTRL bit 3 sets the mode choice for the clock input of IT8784/IT8786.
Some motherboards require this bit to be set to 1 (= PCICLK mode),
otherwise the watchdog functionality gets broken. The BIOS of those
motherboards sets WDTCTRL bit 3 already to 1.
Instead of setting all bits of WDTCTRL to 0 by writing 0x00 to it, keep
bit 3 of it unchanged for IT8784/IT8786 chips. In this way, bit 3 keeps
the status as set by the BIOS of the motherboard.
Watchdog tests have been successful with this patch with the following
systems:
IT8784: Thomas-Krenn LES plus v2 (YANLING YL-KBRL2 V2)
IT8786: Thomas-Krenn LES plus v3 (YANLING YL-CLU L2)
IT8786: Thomas-Krenn LES network 6L v2 (YANLING YL-CLU6L)
In cases where mapping of mpmu/apmu/apbc registers fails, the code path
does not handle the failure gracefully, potentially leading to a memory
leak. This fix ensures proper cleanup by freeing the allocated memory
for 'pxa_unit' before returning.
In cases where kcalloc() fails for the 'clk_data->clks' allocation, the
code path does not handle the failure gracefully, potentially leading
to a memory leak. This fix ensures proper cleanup by freeing the
allocated memory for 'clk_data' before returning.
Issue: during evict or validate happened on amdgpu_bo, the 'from' and
'to' is always same in ftrace event of amdgpu_bo_move
where calling the 'trace_amdgpu_bo_move', the comment says move_notify
is called before move happens, but actually it is called after move
happens, here the new_mem is same as bo->resource
Fix: move trace_amdgpu_bo_move from move_notify to amdgpu_bo_move
Signed-off-by: Wang, Beyond <Wang.Beyond@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Releasing the `priv->lock` while iterating the `priv->multicast_list` in
`ipoib_mcast_join_task()` opens a window for `ipoib_mcast_dev_flush()` to
remove the items while in the middle of iteration. If the mcast is removed
while the lock was dropped, the for loop spins forever resulting in a hard
lockup (as was reported on RHEL 4.18.0-372.75.1.el8_6 kernel):
Task A (kworker/u72:2 below) | Task B (kworker/u72:0 below)
-----------------------------------+-----------------------------------
ipoib_mcast_join_task(work) | ipoib_ib_dev_flush_light(work)
spin_lock_irq(&priv->lock) | __ipoib_ib_dev_flush(priv, ...)
list_for_each_entry(mcast, | ipoib_mcast_dev_flush(dev = priv->dev)
&priv->multicast_list, list) |
ipoib_mcast_join(dev, mcast) |
spin_unlock_irq(&priv->lock) |
| spin_lock_irqsave(&priv->lock, flags)
| list_for_each_entry_safe(mcast, tmcast,
| &priv->multicast_list, list)
| list_del(&mcast->list);
| list_add_tail(&mcast->list, &remove_list)
| spin_unlock_irqrestore(&priv->lock, flags)
spin_lock_irq(&priv->lock) |
| ipoib_mcast_remove_list(&remove_list)
(Here, `mcast` is no longer on the | list_for_each_entry_safe(mcast, tmcast,
`priv->multicast_list` and we keep | remove_list, list)
spinning on the `remove_list` of | >>> wait_for_completion(&mcast->done)
the other thread which is blocked |
and the list is still valid on |
it's stack.)
Fix this by keeping the lock held and changing to GFP_ATOMIC to prevent
eventual sleeps.
Unfortunately we could not reproduce the lockup and confirm this fix but
based on the code review I think this fix should address such lockups.
Based on grepping through the source code this driver appears to be
missing a call to drm_atomic_helper_shutdown() at system shutdown time
and at driver unbind time. Among other things, this means that if a
panel is in use that it won't be cleanly powered off at system
shutdown time.
The fact that we should call drm_atomic_helper_shutdown() in the case
of OS shutdown/restart and at driver remove (or unbind) time comes
straight out of the kernel doc "driver instance overview" in
drm_drv.c.
A few notes about this fix:
- When adding drm_atomic_helper_shutdown() to the unbind path, I added
it after drm_kms_helper_poll_fini() since that's when other drivers
seemed to have it.
- Technically with a previous patch, ("drm/atomic-helper:
drm_atomic_helper_shutdown(NULL) should be a noop"), we don't
actually need to check to see if our "drm" pointer is NULL before
calling drm_atomic_helper_shutdown(). We'll leave the "if" test in,
though, so that this patch can land without any dependencies. It
could potentially be removed later.
- This patch also makes sure to set the drvdata to NULL in the case of
bind errors to make sure that shutdown can't access freed data.
Suggested-by: Maxime Ripard <mripard@kernel.org> Reviewed-by: Maxime Ripard <mripard@kernel.org> Signed-off-by: Douglas Anderson <dianders@chromium.org> Tested-by: Marek Szyprowski <m.szyprowski@samsung.com> Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Inki Dae <inki.dae@samsung.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
It needs to add missing gcing flag on page during block migration,
in order to garantee migrated data be persisted during checkpoint,
otherwise out-of-order persistency between data and node may cause
data corruption after SPOR.
Similar issue was fixed by commit 2d1fe8a86bf5 ("f2fs: fix to tag
gcing flag on page during file defragment").
In all known platforms the ISP has dedicated IRQ lines, but for some
reason the driver uses IRQF_SHARED.
Supporting IRQF_SHARED properly requires handling interrupts even when
our device is disabled, and the driver does not handle this. To avoid
adding such code, and to be sure the driver won't accidentally be used
in a platform with shared interrupts, let's drop the IRQF_SHARED flag.
Link: https://lore.kernel.org/r/20231207-rkisp-irq-fix-v3-1-358a2c871a3c@ideasonboard.com Tested-by: Adam Ford <aford173@gmail.com> #imx8mp-beacon Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com> Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When using 32 bit RGB formats, the RGA on the rk3568 produces wrong
colors as the wrong color channels are read or written. The reason is
that the format description for the channel swizzeling is wrong and the
wrong bits are configured. For example, when converting ARGB32 to NV12,
the alpha channel is used as blue channel.. This doesn't happen if the
color format is the same on both sides.
Fix the color_swap settings of the formats to correctly handle 32 bit
RGB formats.
For RGA_COLOR_FMT_XBGR8888, the RGA_COLOR_ALPHA_SWAP bit doesn't have an
effect. Thus, it isn't possible to handle the V4L2_PIX_FMT_XRGB32. Thus,
it is removed from the list of supported formats.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Sasha Levin <sashal@kernel.org>
The function stk1160_dbg gets called too many times, which causes
the output to get flooded with messages. Since stk1160_dbg uses
printk, it is now replaced with printk_ratelimited.
Suggested-by: Phillip Potter <phil@philpotter.co.uk> Signed-off-by: Ghanshyam Agrawal <ghanshyam1898@gmail.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Sasha Levin <sashal@kernel.org>
After reading the code, I think this is what happens:
We have a DSI host defined in the device tree and a DSI peripheral under
that host (i.e. an i2c device using the DSI as data bus doesn't exhibit
this behavior).
The host driver calls mipi_dsi_host_register(), which causes (via a few
functions) mipi_dsi_device_add() to be called for the DSI peripheral. So
now we have a DSI device under the host, but attach hasn't been called.
Normally the probing of the devices continues, and eventually the DSI
peripheral's driver will call mipi_dsi_attach(), attaching the
peripheral.
However, if the host driver's probe encounters an error after calling
mipi_dsi_host_register(), and before the peripheral has called
mipi_dsi_attach(), the host driver will do cleanups and return an error
from its probe function. The cleanups include calling
mipi_dsi_host_unregister().
mipi_dsi_host_unregister() will call two functions for all its DSI
peripheral devices: mipi_dsi_detach() and mipi_dsi_device_unregister().
The latter makes sense, as the device exists, but the former may be
wrong as attach has not necessarily been done.
To fix this, track the attached state of the peripheral, and only detach
from mipi_dsi_host_unregister() if the peripheral was attached.
Note that I have only tested this with a board with an i2c DSI
peripheral, not with a "pure" DSI peripheral.
However, slightly related, the unregister machinery still seems broken.
E.g. if the DSI host driver is unbound, it'll detach and unregister the
DSI peripherals. After that, when the DSI peripheral driver unbound
it'll call detach either directly or using the devm variant, leading to
a crash. And probably the driver will crash if it happens, for some
reason, to try to send a message via the DSI bus.
But that's another topic.
Tested-by: H. Nikolaus Schaller <hns@goldelico.com> Acked-by: Maxime Ripard <mripard@kernel.org> Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com> Tested-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com> Link: https://patchwork.freedesktop.org/patch/msgid/20230921-dsi-detach-fix-v1-1-d0de2d1621d9@ideasonboard.com Signed-off-by: Sasha Levin <sashal@kernel.org>
drivers/gpu/drm/drm_framebuffer.c:654 drm_mode_getfb2_ioctl() error: uninitialized symbol 'ret'.
'ret' is possibly not set when there are no errors, causing the error
above. I can't say if that ever happens in real-life, but in any case I
think it is good to initialize 'ret' to 0.
drivers/gpu/drm/drm_file.c:967 drm_show_memory_stats() error: uninitialized symbol 'supported_status'.
'supported_status' is only set in one code path. I'm not familiar with
the code to say if that path will always be ran in real life, but
whether that is the case or not, I think it is good to initialize
'supported_status' to 0 to silence the warning (and possibly fix a bug).
If refcount is less than 1, we should just warn, unlock dentry and
return true, so that the caller doesn't try to do anything else.
Taking care of that leaves the rest of "lockref_put_return() has
failed" case equivalent to "decrement refcount and rejoin the
normal slow path after the point where we grab ->d_lock".
NOTE: lockref_put_return() is strictly a fastpath thing - unlike
the rest of lockref primitives, it does not contain a fallback.
Caller (and it looks like fast_dput() is the only legitimate one
in the entire kernel) has to do that itself. Reasons for
lockref_put_return() failures:
* ->d_lock held by somebody
* refcount <= 0
* ... or an architecture not supporting lockref use of
cmpxchg - sparc, anything non-SMP, config with spinlock debugging...
We could add a fallback, but it would be a clumsy API - we'd have
to distinguish between:
(1) refcount > 1 - decremented, lock not held on return
(2) refcount < 1 - left alone, probably no sense to hold the lock
(3) refcount is 1, no cmphxcg - decremented, lock held on return
(4) refcount is 1, cmphxcg supported - decremented, lock *NOT* held
on return.
We want to return with no lock held in case (4); that's the whole point of that
thing. We very much do not want to have the fallback in case (3) return without
a lock, since the caller might have to retake it in that case.
So it wouldn't be more convenient than doing the fallback in the caller and
it would be very easy to screw up, especially since the test coverage would
suck - no way to test (3) and (4) on the same kernel build.
Reviewed-by: Christian Brauner <brauner@kernel.org> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Sasha Levin <sashal@kernel.org>
The virtual widget example makes use of an undefined SND_SOC_DAPM_NOPM
argument passed to SND_SOC_DAPM_MIXER(). Replace with the correct
SND_SOC_NOPM definition.
In a couple of loops over the all streams, we check the bitmap against
the loop counter. A more correct reference would be, however, the
index of each stream, instead.
This patch corrects the check of bitmaps to the stream index.
Note that this change doesn't fix anything for now; all existing
drivers set up the stream indices properly, hence the loop count is
always equal with the stream index. That said, this change is only
for consistency.
Let's check return value of f2fs_reserve_new_block() in do_recover_data()
rather than letting it fails silently.
Also refactoring check condition on return value of f2fs_reserve_new_block()
as below:
- trigger f2fs_bug_on() only for ENOSPC case;
- use do-while statement to avoid redundant codes;
As of today, the last MCAM entry was not getting allocated because of
a <= check with the max_bmap count. This patch modifies that and if the
requested entry is greater than the available entries then set it to the
max value.
Currently, if a VF is disabled using the
'ip link set dev $ETHX vf $VF_NUM state disable' command, the VF is still
able to receive traffic.
Fix the behavior of the 'ip link set dev $ETHX vf $VF_NUM state disable'
to completely shutdown the VF's queues making it entirely disabled and
not able to receive or send any traffic.
Modify the behavior of the 'ip link set $ETHX vf $VF_NUM state enable'
command to make a VF do reinitialization bringing the queues back up.
Co-developed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com> Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com> Reviewed-by: Jan Sokolowski <jan.sokolowski@intel.com> Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com> Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com> Signed-off-by: Andrii Staikov <andrii.staikov@intel.com> Tested-by: Rafal Romanowski <rafal.romanowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
It appears that there is a typo in the code where the nlattr array is
being parsed with policy br_cfm_cc_ccm_tx_policy, but the instance is
being accessed via IFLA_BRIDGE_CFM_CC_RDI_INSTANCE, which is associated
with the policy br_cfm_cc_rdi_policy.
This problem was introduced by commit 2be665c3940d ("bridge: cfm: Netlink
SET configuration Interface.").
Though it seems like a harmless typo since these two enum owns the exact
same value (1 here), it is quite misleading hence fix it by using the
correct enum IFLA_BRIDGE_CFM_CC_CCM_TX_INSTANCE here.
Signed-off-by: Lin Ma <linma@zju.edu.cn> Reviewed-by: Simon Horman <horms@kernel.org> Acked-by: Nikolay Aleksandrov <razor@blackwall.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
In case of an incomplete command or a command with a null identifier 2
reject packets will be sent, one with the identifier and one with 0.
Consuming the data of the command will prevent it.
This allows to send a reject packet for each corrupted command in a
multi-command packet.
Signed-off-by: Frédéric Danis <frederic.danis@collabora.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Set both WIDEBAND_SPEECH_SUPPORTED and VALID_LE_STATES quirks
for QCA2066.
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
This is a more of a cosmetic fix. The branch will only be taken if
proberesp_ies is set, which implies that beacon_ies is not set unless we
are connected to an AP that just did a channel switch. And, in that case
we should have found the BSS in the internal storage to begin with.
An issue occurred while reading an ELF file in libbpf.c during fuzzing:
Program received signal SIGSEGV, Segmentation fault.
0x0000000000958e97 in bpf_object.collect_prog_relos () at libbpf.c:4206
4206 in libbpf.c
(gdb) bt
#0 0x0000000000958e97 in bpf_object.collect_prog_relos () at libbpf.c:4206
#1 0x000000000094f9d6 in bpf_object.collect_relos () at libbpf.c:6706
#2 0x000000000092bef3 in bpf_object_open () at libbpf.c:7437
#3 0x000000000092c046 in bpf_object.open_mem () at libbpf.c:7497
#4 0x0000000000924afa in LLVMFuzzerTestOneInput () at fuzz/bpf-object-fuzzer.c:16
#5 0x000000000060be11 in testblitz_engine::fuzzer::Fuzzer::run_one ()
#6 0x000000000087ad92 in tracing::span::Span::in_scope ()
#7 0x00000000006078aa in testblitz_engine::fuzzer::util::walkdir ()
#8 0x00000000005f3217 in testblitz_engine::entrypoint::main::{{closure}} ()
#9 0x00000000005f2601 in main ()
(gdb)
scn_data was null at this code(tools/lib/bpf/src/libbpf.c):
if (rel->r_offset % BPF_INSN_SZ || rel->r_offset >= scn_data->d_size) {
Upon assembling the array, both kernel and mdadm allow the devices to have event
counter difference of 1, and still consider them as up-to-date.
However, a device whose event count is behind by 1, may in fact not be up-to-date,
and array resync with such a device may cause data corruption.
To avoid this, consult the superblock of the freshest device about the status
of a device, whose event counter is behind by 1.
mv88e6xxx_get_stats, which collects stats from various sources,
expects all callees to return the number of stats read. If an error
occurs, 0 should be returned.
Prevent future mishaps of this kind by updating the return type to
reflect this contract.
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com> Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Per fsl,mxs-dma.yaml, the node name should be 'dma-controller'.
Change it to fix the following dt-schema warning.
imx28-apf28.dtb: dma-apbx@80024000: $nodename:0: 'dma-apbx@80024000' does not match '^dma-controller(@.*)?$'
from schema $id: http://devicetree.org/schemas/dma/fsl,mxs-dma.yaml#
The 'gpios' property to describe the SDA and SCL GPIOs is considered
deprecated according to i2c-gpio.yaml.
Switch to the preferred 'sda-gpios' and 'scl-gpios' properties.
This fixes the following schema warnings:
imx23-sansa.dtb: i2c-0: 'sda-gpios' is a required property
from schema $id: http://devicetree.org/schemas/i2c/i2c-gpio.yaml#
imx23-sansa.dtb: i2c-0: 'scl-gpios' is a required property
from schema $id: http://devicetree.org/schemas/i2c/i2c-gpio.yaml#
Per leds-gpio.yaml, the led names should start with 'led'.
Change it to fix the following dt-schema warning:
imx27-apf27dev.dtb: leds: 'user' does not match any of the regexes: '(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/leds/leds-gpio.yaml#
Per display-timings.yaml, the 'timing' pattern should be used to
describe the display timings.
Change it accordingly to fix the following dt-schema warning:
imx27-apf27dev.dtb: display-timings: '800x480' does not match any of the regexes: '^timing', 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/display/panel/display-timings.yaml#
Per imx-iim.yaml, the compatible string should only contain a single
entry.
Use it as "fsl,imx25-iim" to fix the following dt-schema warning:
imx25-karo-tx25.dtb: efuse@53ff0000: compatible: ['fsl,imx25-iim', 'fsl,imx27-iim'] is too long
from schema $id: http://devicetree.org/schemas/nvmem/imx-iim.yaml#
Since "dev_search_path" can technically be as large as PATH_MAX,
there was a risk of truncation when copying it and a second string
into "full_path" since it was also PATH_MAX sized. The W=1 builds were
reporting this warning:
drivers/block/rnbd/rnbd-srv.c: In function 'process_msg_open.isra':
drivers/block/rnbd/rnbd-srv.c:616:51: warning: '%s' directive output may be truncated writing up to 254 bytes into a region of size between 0 and 4095 [-Wformat-truncation=]
616 | snprintf(full_path, PATH_MAX, "%s/%s",
| ^~
In function 'rnbd_srv_get_full_path',
inlined from 'process_msg_open.isra' at drivers/block/rnbd/rnbd-srv.c:721:14: drivers/block/rnbd/rnbd-srv.c:616:17: note: 'snprintf' output between 2 and 4351 bytes into a destination of size 4096
616 | snprintf(full_path, PATH_MAX, "%s/%s",
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
617 | dev_search_path, dev_name);
| ~~~~~~~~~~~~~~~~~~~~~~~~~~
To fix this, unconditionally check for truncation (as was already done
for the case where "%SESSNAME%" was present).
Reported-by: kernel test robot <lkp@intel.com> Closes: https://lore.kernel.org/oe-kbuild-all/202312100355.lHoJPgKy-lkp@intel.com/ Cc: Md. Haris Iqbal <haris.iqbal@ionos.com> Cc: Jack Wang <jinpu.wang@ionos.com> Cc: Jens Axboe <axboe@kernel.dk> Cc: <linux-block@vger.kernel.org> Signed-off-by: Kees Cook <keescook@chromium.org> Acked-by: Guoqing Jiang <guoqing.jiang@linux.dev> Acked-by: Jack Wang <jinpu.wang@ionos.com> Link: https://lore.kernel.org/r/20231212214738.work.169-kees@kernel.org Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
Don't rely on the PCI memory for the devcmd opcode because we
read a 0xff value if the PCI bus is broken, which can cause us
to report a bogus dev_cmd opcode later.
Signed-off-by: Shannon Nelson <shannon.nelson@amd.com> Reviewed-by: Brett Creeley <brett.creeley@amd.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / thirdparty / kernel / stable.git / log
