When VLAN filtering is off, we configure the switch to forward, but not
learn on VLAN table misses. This effectively disables learning while not
filtering.
Fix this by switching to forward and learn. Setting the learning disable
register will still control whether learning actually happens.
Currently the PVID of ports are only set when adding/updating VLANs with
PVID set or removing VLANs, but not when clearing the PVID flag of a
VLAN.
E.g. the following flow
$ ip link add br0 type bridge vlan_filtering 1
$ ip link set sw1p1 master bridge
$ bridge vlan add dev sw1p1 vid 10 pvid untagged
$ bridge vlan add dev sw1p1 vid 10 untagged
Would keep the PVID set as 10, despite the flag being cleared. Fix this
by checking if we need to unset the PVID on vlan updates.
Allow reserved multicast to ignore VLAN membership so STP and other
management protocols work without a PVID VLAN configured when using a
vlan aware bridge.
Fixes: 967dd82ffc52 ("net: dsa: b53: Add support for Broadcom RoboSwitch") Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com> Tested-by: Florian Fainelli <florian.fainelli@broadcom.com> Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com> Link: https://patch.msgid.link/20250429201710.330937-2-jonas.gorski@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When bpf_redirect_peer is used to redirect packets to a device in
another network namespace, the skb isn't scrubbed. That can lead skb
information from one namespace to be "misused" in another namespace.
As one example, this is causing Cilium to drop traffic when using
bpf_redirect_peer to redirect packets that just went through IPsec
decryption to a container namespace. The following pwru trace shows (1)
the packet path from the host's XFRM layer to the container's XFRM
layer where it's dropped and (2) the number of active skb extensions at
each function.
In this case, there are no XFRM policies in the container's network
namespace so the drop is unexpected. When we decrypt the IPsec packet,
the XFRM state used for decryption is set in the skb extensions. This
information is preserved across the netns switch. When we reach the
XFRM policy check in the container's netns, __xfrm_policy_check drops
the packet with LINUX_MIB_XFRMINNOPOLS because a (container-side) XFRM
policy can't be found that matches the (host-side) XFRM state used for
decryption.
This patch fixes this by scrubbing the packet when using
bpf_redirect_peer, as is done on typical netns switches via veth
devices except skb->mark and skb->tstamp are not zeroed.
Region locking introduced in v5.6-rc4 contained three macros to handle
the region locks: ahash_bucket_start(), ahash_bucket_end() which gave
back the start and end hash bucket values belonging to a given region
lock and ahash_region() which should give back the region lock belonging
to a given hash bucket. The latter was incorrect which can lead to a
race condition between the garbage collector and adding new elements
when a hash type of set is defined with timeouts.
Fixes: f66ee0410b1c ("netfilter: ipset: Fix "INFO: rcu detected stall in hash_xxx" reports") Reported-by: Kota Toda <kota.toda@gmo-cybersecurity.com> Signed-off-by: Jozsef Kadlecsik <kadlec@netfilter.org> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
syzbot reports for uninit-value for the saddr argument [1].
commit 4754957f04f5 ("ipvs: do not use random local source address for
tunnels") already implies that the input value of saddr
should be ignored but the code is still reading it which can prevent
to connect the route. Fix it by changing the argument to ret_saddr.
CPU: 0 UID: 0 PID: 22408 Comm: syz.4.5165 Not tainted 6.15.0-rc3-syzkaller-00019-gbc3372351d0c #0 PREEMPT(undef)
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 02/12/2025
Reported-by: syzbot+04b9a82855c8aed20860@syzkaller.appspotmail.com Closes: https://lore.kernel.org/netdev/68138dfa.050a0220.14dd7d.0017.GAE@google.com/ Fixes: 4754957f04f5 ("ipvs: do not use random local source address for tunnels") Signed-off-by: Julian Anastasov <ja@ssi.bg> Acked-by: Simon Horman <horms@kernel.org> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
As reported by Sebastian Andrzej Siewior the use of local_bh_disable()
is only feasible in uni processor systems to update the modification rules.
The usual use-case to update the modification rules is to update the data
of the modifications but not the modification types (AND/OR/XOR/SET) or
the checksum functions itself.
To omit additional memory allocations to maintain fast modification
switching times, the modification description space is doubled at gw-job
creation time so that only the reference to the active modification
description is changed under rcu protection.
Rename cgw_job::mod to cf_mod and make it a RCU pointer. Allocate in
cgw_create_job() and free it together with cgw_job in
cgw_job_free_rcu(). Update all users to dereference cgw_job::cf_mod with
a RCU accessor and if possible once.
[bigeasy: Replace mod1/mod2 from the Oliver's original patch with dynamic
allocation, use RCU annotation and accessor]
Reported-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Closes: https://lore.kernel.org/linux-can/20231031112349.y0aLoBrz@linutronix.de/ Fixes: dd895d7f21b2 ("can: cangw: introduce optional uid to reference created routing jobs") Tested-by: Oliver Hartkopp <socketcan@hartkopp.net> Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net> Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Link: https://patch.msgid.link/20250429070555.cs-7b_eZ@linutronix.de Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
The TDC is currently hardcoded enabled. This means that even for lower
CAN-FD data bitrates (with a DBRP (data bitrate prescaler) > 2) a TDC
is configured. This leads to a bus-off condition.
ISO 11898-1 section 11.3.3 says "Transmitter delay compensation" (TDC)
is only applicable if DBRP is 1 or 2.
To fix the problem, switch the driver to use the TDC calculation
provided by the CAN driver framework (which respects ISO 11898-1
section 11.3.3). This has the positive side effect that userspace can
control TDC as needed.
Demonstration of the feature in action:
| $ ip link set can0 up type can bitrate 125000 dbitrate 500000 fd on
| $ ip -details link show can0
| 3: can0: <NOARP,UP,LOWER_UP,ECHO> mtu 72 qdisc pfifo_fast state UP mode DEFAULT group default qlen 10
| link/can promiscuity 0 allmulti 0 minmtu 0 maxmtu 0
| can <FD> state ERROR-ACTIVE (berr-counter tx 0 rx 0) restart-ms 0
| bitrate 125000 sample-point 0.875
| tq 50 prop-seg 69 phase-seg1 70 phase-seg2 20 sjw 10 brp 2
| mcp251xfd: tseg1 2..256 tseg2 1..128 sjw 1..128 brp 1..256 brp_inc 1
| dbitrate 500000 dsample-point 0.875
| dtq 125 dprop-seg 6 dphase-seg1 7 dphase-seg2 2 dsjw 1 dbrp 5
| mcp251xfd: dtseg1 1..32 dtseg2 1..16 dsjw 1..16 dbrp 1..256 dbrp_inc 1
| tdcv 0..63 tdco 0..63
| clock 40000000 numtxqueues 1 numrxqueues 1 gso_max_size 65536 gso_max_segs 65535 tso_max_size 65536 tso_max_segs 65535 gro_max_size 65536 parentbus spi parentdev spi0.0
| $ ip link set can0 up type can bitrate 1000000 dbitrate 4000000 fd on
| $ ip -details link show can0
| 3: can0: <NOARP,UP,LOWER_UP,ECHO> mtu 72 qdisc pfifo_fast state UP mode DEFAULT group default qlen 10
| link/can promiscuity 0 allmulti 0 minmtu 0 maxmtu 0
| can <FD,TDC-AUTO> state ERROR-ACTIVE (berr-counter tx 0 rx 0) restart-ms 0
| bitrate 1000000 sample-point 0.750
| tq 25 prop-seg 14 phase-seg1 15 phase-seg2 10 sjw 5 brp 1
| mcp251xfd: tseg1 2..256 tseg2 1..128 sjw 1..128 brp 1..256 brp_inc 1
| dbitrate 4000000 dsample-point 0.700
| dtq 25 dprop-seg 3 dphase-seg1 3 dphase-seg2 3 dsjw 1 dbrp 1
| tdco 7
| mcp251xfd: dtseg1 1..32 dtseg2 1..16 dsjw 1..16 dbrp 1..256 dbrp_inc 1
| tdcv 0..63 tdco 0..63
| clock 40000000 numtxqueues 1 numrxqueues 1 gso_max_size 65536 gso_max_segs 65535 tso_max_size 65536 tso_max_segs 65535 gro_max_size 65536 parentbus spi parentdev spi0.0
There has been some confusion about the MCP2518FD using a relative or
absolute TDCO due to the datasheet specifying a range of [-64,63]. I
have a custom board with a 40 MHz clock and an estimated loop delay of
100 to 216 ns. During testing at a data bit rate of 4 Mbit/s I found
that using can_get_relative_tdco() resulted in bus-off errors. The
final TDCO value was 1 which corresponds to a 10% SSP in an absolute
configuration. This behavior is expected if the TDCO value is really
absolute and not relative. Using priv->can.tdc.tdco instead results in
a final TDCO of 8, setting the SSP at exactly 80%. This configuration
works.
The automatic, manual, and off TDC modes were tested at speeds up to,
and including, 8 Mbit/s on real hardware and behave as expected.
Use addrconf_addr_gen() to generate IPv6 link-local addresses on GRE
devices in most cases and fall back to using add_v4_addrs() only in
case the GRE configuration is incompatible with addrconf_addr_gen().
GRE used to use addrconf_addr_gen() until commit e5dd729460ca ("ip/ip6_gre:
use the same logic as SIT interfaces when computing v6LL address")
restricted this use to gretap and ip6gretap devices, and created
add_v4_addrs() (borrowed from SIT) for non-Ethernet GRE ones.
The original problem came when commit 9af28511be10 ("addrconf: refuse
isatap eui64 for INADDR_ANY") made __ipv6_isatap_ifid() fail when its
addr parameter was 0. The commit says that this would create an invalid
address, however, I couldn't find any RFC saying that the generated
interface identifier would be wrong. Anyway, since gre over IPv4
devices pass their local tunnel address to __ipv6_isatap_ifid(), that
commit broke their IPv6 link-local address generation when the local
address was unspecified.
Then commit e5dd729460ca ("ip/ip6_gre: use the same logic as SIT
interfaces when computing v6LL address") tried to fix that case by
defining add_v4_addrs() and calling it to generate the IPv6 link-local
address instead of using addrconf_addr_gen() (apart for gretap and
ip6gretap devices, which would still use the regular
addrconf_addr_gen(), since they have a MAC address).
That broke several use cases because add_v4_addrs() isn't properly
integrated into the rest of IPv6 Neighbor Discovery code. Several of
these shortcomings have been fixed over time, but add_v4_addrs()
remains broken on several aspects. In particular, it doesn't send any
Router Sollicitations, so the SLAAC process doesn't start until the
interface receives a Router Advertisement. Also, add_v4_addrs() mostly
ignores the address generation mode of the interface
(/proc/sys/net/ipv6/conf/*/addr_gen_mode), thus breaking the
IN6_ADDR_GEN_MODE_RANDOM and IN6_ADDR_GEN_MODE_STABLE_PRIVACY cases.
Fix the situation by using add_v4_addrs() only in the specific scenario
where the normal method would fail. That is, for interfaces that have
all of the following characteristics:
* run over IPv4,
* transport IP packets directly, not Ethernet (that is, not gretap
interfaces),
* tunnel endpoint is INADDR_ANY (that is, 0),
* device address generation mode is EUI64.
In all other cases, revert back to the regular addrconf_addr_gen().
Also, remove the special case for ip6gre interfaces in add_v4_addrs(),
since ip6gre devices now always use addrconf_addr_gen() instead.
Note:
This patch was originally applied as commit 183185a18ff9 ("gre: Fix
IPv6 link-local address generation."). However, it was then reverted
by commit fc486c2d060f ("Revert "gre: Fix IPv6 link-local address
generation."") because it uncovered another bug that ended up
breaking net/forwarding/ip6gre_custom_multipath_hash.sh. That other
bug has now been fixed by commit 4d0ab3a6885e ("ipv6: Start path
selection from the first nexthop"). Therefore we can now revive this
GRE patch (no changes since original commit 183185a18ff9 ("gre: Fix
IPv6 link-local address generation.").
Fixes: e5dd729460ca ("ip/ip6_gre: use the same logic as SIT interfaces when computing v6LL address") Signed-off-by: Guillaume Nault <gnault@redhat.com> Reviewed-by: Ido Schimmel <idosch@nvidia.com> Link: https://patch.msgid.link/a88cc5c4811af36007645d610c95102dccb360a6.1746225214.git.gnault@redhat.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
For htb_next_rb_node(), after calling the 1st htb_deactivate(), the
clprio[prio]->ptr could be already set to NULL, which means
htb_next_rb_node() is vulnerable here.
For htb_deactivate(), although we checked qlen before calling it, in
case of qlen==0 after qdisc_tree_reduce_backlog(), we may call it again
which triggers the warning inside.
To fix the issues here, we need to:
1) Make htb_deactivate() idempotent, that is, simply return if we
already call it before.
2) Make htb_next_rb_node() safe against ptr==NULL.
Many thanks to Alan for testing and for the reproducer.
Fixes: 5ba8b837b522 ("sch_htb: make htb_qlen_notify() idempotent") Reported-by: Alan J. Wylie <alan@wylie.me.uk> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Link: https://patch.msgid.link/20250428232955.1740419-2-xiyou.wangcong@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The previous patch that added bounds check for create lease context
introduced a memory leak. When the bounds check fails, the function
returns NULL without freeing the previously allocated lease_ctx_info
structure.
This patch fixes the issue by adding kfree(lreq) before returning NULL
in both boundary check cases.
Fixes: bab703ed8472 ("ksmbd: add bounds check for create lease context") Signed-off-by: Wang Zhaolong <wangzhaolong1@huawei.com> Acked-by: Namjae Jeon <linkinjeon@kernel.org> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
This patch replaces the manual Netlink attribute iteration in
output_userspace() with nla_for_each_nested(), which ensures that only
well-formed attributes are processed.
A use-after-free is possible if one thread destroys the file
via __ksmbd_close_fd while another thread holds a reference to
it. The existing checks on fp->refcount are not sufficient to
prevent this.
The fix takes ft->lock around the section which removes the
file from the file table. This prevents two threads acquiring the
same file pointer via __close_file_table_ids, as well as the other
functions which retrieve a file from the IDR and which already use
this same lock.
Cc: stable@vger.kernel.org Signed-off-by: Sean Heelan <seanheelan@gmail.com> Acked-by: Namjae Jeon <linkinjeon@kernel.org> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ksmbd_vfs_stream_write() did not validate whether the write offset
(*pos) was within the bounds of the existing stream data length (v_len).
If *pos was greater than or equal to v_len, this could lead to an
out-of-bounds memory write.
This patch adds a check to ensure *pos is less than v_len before
proceeding. If the condition fails, -EINVAL is returned.
Cc: stable@vger.kernel.org Signed-off-by: Norbert Szetei <norbert@doyensec.com> Acked-by: Namjae Jeon <linkinjeon@kernel.org> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Client can send empty newname string to ksmbd server.
It will cause a kernel oops from d_alloc.
This patch return the error when attempting to rename
a file or directory with an empty new name string.
If a driver is removed, the driver framework invokes the driver's
remove callback. A CAN driver's remove function calls
unregister_candev(), which calls net_device_ops::ndo_stop further down
in the call stack for interfaces which are in the "up" state.
With the mcp251xfd driver the removal of the module causes the
following warning:
| WARNING: CPU: 0 PID: 352 at net/core/dev.c:7342 __netif_napi_del_locked+0xc8/0xd8
as can_rx_offload_del() deletes the NAPI, while it is still active,
because the interface is still up.
To fix the warning, first unregister the network interface, which
calls net_device_ops::ndo_stop, which disables the NAPI, and then call
can_rx_offload_del().
Currently during the multi-link element defragmentation process, the
multi-link element length added to the total IEs length when calculating
the length of remaining IEs after the multi-link element in
cfg80211_defrag_mle(). This could lead to out-of-bounds access if the
multi-link element or its corresponding fragment elements are the last
elements in the IEs buffer.
To address this issue, correctly calculate the remaining IEs length by
deducting the multi-link element end offset from total IEs end offset.
Cc: stable@vger.kernel.org Fixes: 2481b5da9c6b ("wifi: cfg80211: handle BSS data contained in ML probe responses") Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com> Link: https://patch.msgid.link/20250424-fix_mle_defragmentation_oob_access-v1-1-84412a1743fa@quicinc.com Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a driver is removed, the driver framework invokes the driver's
remove callback. A CAN driver's remove function calls
unregister_candev(), which calls net_device_ops::ndo_stop further down
in the call stack for interfaces which are in the "up" state.
The removal of the module causes a warning, as can_rx_offload_del()
deletes the NAPI, while it is still active, because the interface is
still up.
To fix the warning, first unregister the network interface, which
calls net_device_ops::ndo_stop, which disables the NAPI, and then call
can_rx_offload_del().
Fixes: 1be37d3b0414 ("can: m_can: fix periph RX path: use rx-offload to ensure skbs are sent from softirq context") Cc: stable@vger.kernel.org Link: https://patch.msgid.link/20250502-can-rx-offload-del-v1-3-59a9b131589d@pengutronix.de Reviewed-by: Markus Schneider-Pargmann <msp@baylibre.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Define vqmmc regulator-gpio for usdhc2 with vin-supply
coming from LDO5.
Without this definition LDO5 will be powered down, disabling
SD card after bootup. This has been introduced in commit f5aab0438ef1 ("regulator: pca9450: Fix enable register for LDO5").
Fixes: 6a57f224f734 ("arm64: dts: freescale: add initial support for verdin imx8m mini") Fixes: f5aab0438ef1 ("regulator: pca9450: Fix enable register for LDO5") Tested-by: Manuel Traut <manuel.traut@mt.com> Reviewed-by: Philippe Schenker <philippe.schenker@impulsing.ch> Tested-by: Francesco Dolcini <francesco.dolcini@toradex.com> Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com> Cc: stable@vger.kernel.org Signed-off-by: Wojciech Dubowik <Wojciech.Dubowik@mt.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The blammed commit copied to argv the size of the reallocated argv,
instead of the size of the old_argv, thus reading and copying from
past the old_argv allocated memory.
Don't try to remove a secondary interrupter that is known to be invalid.
Also check if the interrupter is valid inside the spinlock that protects
the array of interrupters.
Found by smatch static checker
Reported-by: Dan Carpenter <dan.carpenter@linaro.org> Closes: https://lore.kernel.org/linux-usb/ffaa0a1b-5984-4a1f-bfd3-9184630a97b9@moroto.mountain/ Fixes: c99b38c41234 ("xhci: add support to allocate several interrupters") Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Link: https://lore.kernel.org/r/20240125152737.2983959-2-mathias.nyman@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If xhci_mem_init() fails, it calls into xhci_mem_cleanup() to mop
up the damage. If it fails early enough, before xhci->interrupters
is allocated but after xhci->max_interrupters has been set, which
happens in most (all?) cases, things get uglier, as xhci_mem_cleanup()
unconditionally derefences xhci->interrupters. With prejudice.
Gate the interrupt freeing loop with a check on xhci->interrupters
being non-NULL.
Found while debugging a DMA allocation issue that led the XHCI driver
on this exact path.
The HDCP code in amdgpu_dm_hdcp.c copies pointers to amdgpu_dm_connector
objects without incrementing the kref reference counts. When using a
USB-C dock, and the dock is unplugged, the corresponding
amdgpu_dm_connector objects are freed, creating dangling pointers in the
HDCP code. When the dock is plugged back, the dangling pointers are
dereferenced, resulting in a slab-use-after-free:
[ 66.775837] BUG: KASAN: slab-use-after-free in event_property_validate+0x42f/0x6c0 [amdgpu]
[ 66.776171] Read of size 4 at addr ffff888127804120 by task kworker/0:1/10
ASPEED VGA card has two built-in devices:
0008:06:00.0 PCI bridge: ASPEED Technology, Inc. AST1150 PCI-to-PCI Bridge (rev 06)
0008:07:00.0 VGA compatible controller: ASPEED Technology, Inc. ASPEED Graphics Family (rev 52)
Its toplogy looks like this:
+-[0008:00]---00.0-[01-09]--+-00.0-[02-09]--+-00.0-[03]----00.0 Sandisk Corp Device 5017
| +-01.0-[04]--
| +-02.0-[05]----00.0 NVIDIA Corporation Device
| +-03.0-[06-07]----00.0-[07]----00.0 ASPEED Technology, Inc. ASPEED Graphics Family
| +-04.0-[08]----00.0 Renesas Technology Corp. uPD720201 USB 3.0 Host Controller
| \-05.0-[09]----00.0 Realtek Semiconductor Co., Ltd. RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller
\-00.1 PMC-Sierra Inc. Device 4028
The IORT logic populaties two identical IDs into the fwspec->ids array via
DMA aliasing in iort_pci_iommu_init() called by pci_for_each_dma_alias().
Though the SMMU driver had been able to handle this situation since commit 563b5cbe334e ("iommu/arm-smmu-v3: Cope with duplicated Stream IDs"), that
got broken by the later commit cdf315f907d4 ("iommu/arm-smmu-v3: Maintain
a SID->device structure"), which ended up with allocating separate streams
with the same stuffing.
On a kernel prior to v6.15-rc1, there has been an overlooked warning:
pci 0008:07:00.0: vgaarb: setting as boot VGA device
pci 0008:07:00.0: vgaarb: bridge control possible
pci 0008:07:00.0: vgaarb: VGA device added: decodes=io+mem,owns=none,locks=none
pcieport 0008:06:00.0: Adding to iommu group 14
ast 0008:07:00.0: stream 67328 already in tree <===== WARNING
ast 0008:07:00.0: enabling device (0002 -> 0003)
ast 0008:07:00.0: Using default configuration
ast 0008:07:00.0: AST 2600 detected
ast 0008:07:00.0: [drm] Using analog VGA
ast 0008:07:00.0: [drm] dram MCLK=396 Mhz type=1 bus_width=16
[drm] Initialized ast 0.1.0 for 0008:07:00.0 on minor 0
ast 0008:07:00.0: [drm] fb0: astdrmfb frame buffer device
With v6.15-rc, since the commit bcb81ac6ae3c ("iommu: Get DT/ACPI parsing
into the proper probe path"), the error returned with the warning is moved
to the SMMU device probe flow:
arm_smmu_probe_device+0x15c/0x4c0
__iommu_probe_device+0x150/0x4f8
probe_iommu_group+0x44/0x80
bus_for_each_dev+0x7c/0x100
bus_iommu_probe+0x48/0x1a8
iommu_device_register+0xb8/0x178
arm_smmu_device_probe+0x1350/0x1db0
which then fails the entire SMMU driver probe:
pci 0008:06:00.0: Adding to iommu group 21
pci 0008:07:00.0: stream 67328 already in tree
arm-smmu-v3 arm-smmu-v3.9.auto: Failed to register iommu
arm-smmu-v3 arm-smmu-v3.9.auto: probe with driver arm-smmu-v3 failed with error -22
Since SMMU driver had been already expecting a potential duplicated Stream
ID in arm_smmu_install_ste_for_dev(), change the arm_smmu_insert_master()
routine to ignore a duplicated ID from the fwspec->sids array as well.
Note: this has been failing the iommu_device_probe() since 2021, although a
recent iommu commit in v6.15-rc1 that moves iommu_device_probe() started to
fail the SMMU driver probe. Since nobody has cared about DMA Alias support,
leave that as it was but fix the fundamental iommu_device_probe() breakage.
Fixes: cdf315f907d4 ("iommu/arm-smmu-v3: Maintain a SID->device structure") Cc: stable@vger.kernel.org Suggested-by: Jason Gunthorpe <jgg@nvidia.com> Reviewed-by: Jason Gunthorpe <jgg@nvidia.com> Signed-off-by: Nicolin Chen <nicolinc@nvidia.com> Link: https://lore.kernel.org/r/20250415185620.504299-1-nicolinc@nvidia.com Signed-off-by: Will Deacon <will@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Since v5.12 the rbtree has gained some simplifying helpers aimed at making
rb tree users write less convoluted boiler plate code. Instead the caller
provides a single comparison function and the helpers generate the prior
open-coded stuff.
Update smmu->streams to use rb_find_add() and rb_find().
Tested-by: Nicolin Chen <nicolinc@nvidia.com> Reviewed-by: Mostafa Saleh <smostafa@google.com> Signed-off-by: Jason Gunthorpe <jgg@nvidia.com> Link: https://lore.kernel.org/r/1-v3-9fef8cdc2ff6+150d1-smmuv3_tidy_jgg@nvidia.com Signed-off-by: Will Deacon <will@kernel.org>
Stable-dep-of: b00d24997a11 ("iommu/arm-smmu-v3: Fix iommu_device_probe bug due to duplicated stream ids") Signed-off-by: Sasha Levin <sashal@kernel.org>
module_add_driver() relies on module_kset list for
/sys/module/<built-in-module>/drivers directory creation.
Since,
commit 96a1a2412acba ("kernel/params.c: defer most of param_sysfs_init() to late_initcall time")
drivers which are initialized from subsys_initcall() or any other
higher precedence initcall couldn't find the related kobject entry
in the module_kset list because module_kset is not fully populated
by the time module_add_driver() refers it. As a consequence,
module_add_driver() returns early without calling make_driver_name().
Therefore, /sys/module/<built-in-module>/drivers is never created.
Fix this issue by letting module_add_driver() handle module_kobject
creation itself.
Fixes: 96a1a2412acb ("kernel/params.c: defer most of param_sysfs_init() to late_initcall time") Cc: stable@vger.kernel.org # requires all other patches from the series Suggested-by: Rasmus Villemoes <linux@rasmusvillemoes.dk> Signed-off-by: Shyam Saini <shyamsaini@linux.microsoft.com> Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Link: https://lore.kernel.org/r/20250227184930.34163-5-shyamsaini@linux.microsoft.com Signed-off-by: Petr Pavlu <petr.pavlu@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
lookup_or_create_module_kobject() is marked as static and __init,
to make it global drop static keyword.
Since this function can be called from non-init code, use __modinit
instead of __init, __modinit marker will make it __init if
CONFIG_MODULES is not defined.
The locate_module_kobject() function looks up an existing
module_kobject for a given module name. If it cannot find the
corresponding module_kobject, it creates one for the given name.
This commit renames locate_module_kobject() to
lookup_or_create_module_kobject() to better describe its operations.
Current xhci bus resume implementation prevents xHC host from generating
interrupts during high-speed USB 2 and super-speed USB 3 bus resume.
Only reason to disable interrupts during bus resume would be to prevent
the interrupt handler from interfering with the resume process of USB 2
ports.
Host initiated resume of USB 2 ports is done in two stages.
The xhci driver first transitions the port from 'U3' to 'Resume' state,
then wait in Resume for 20ms, and finally moves port to U0 state.
xhci driver can't prevent interrupts by keeping the xhci spinlock
due to this 20ms sleep.
Limit interrupt disabling to the USB 2 port resume case only.
resuming USB 2 ports in bus resume is only done in special cases where
USB 2 ports had to be forced to suspend during bus suspend.
The current way of preventing interrupts by clearing the 'Interrupt
Enable' (INTE) bit in USBCMD register won't prevent the Interrupter
registers 'Interrupt Pending' (IP), 'Event Handler Busy' (EHB) and
USBSTS register Event Interrupt (EINT) bits from being set.
New interrupts can't be issued before those bits are properly clered.
Disable interrupts by clearing the interrupter register 'Interrupt
Enable' (IE) bit instead. This way IP, EHB and INTE won't be set
before IE is enabled again and a new interrupt is triggered.
Check if requested segments ('segs' or 'ERST_DEFAULT_SEGS') exceeds the
maximum amount ERST supports.
When 'segs' is '0', 'ERST_DEFAULT_SEGS' is used instead. But both values
may not exceed ERST max.
Macro 'ERST_MAX_SEGS' is renamed to 'ERST_DEFAULT_SEGS'. The new name
better represents the macros, which is the number of Event Ring segments
to allocate, when the amount is not specified.
Additionally, rename and change xhci_create_secondary_interrupter()'s
argument 'int num_segs' to 'unsigned int segs'. This makes it the same
as its counter part in xhci_alloc_interrupter().
Fixes: c99b38c41234 ("xhci: add support to allocate several interrupters") Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Link: https://lore.kernel.org/r/20240429140245.3955523-4-mathias.nyman@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: bea5892d0ed2 ("xhci: Limit time spent with xHC interrupts disabled during bus resume") Signed-off-by: Sasha Levin <sashal@kernel.org>
Modify the XHCI drivers to accommodate for handling multiple event rings in
case there are multiple interrupters. Add the required APIs so clients are
able to allocate/request for an interrupter ring, and pass this information
back to the client driver. This allows for users to handle the resource
accordingly, such as passing the event ring base address to an audio DSP.
There is no actual support for multiple MSI/MSI-X vectors.
[export xhci_initialize_ring_info() -wcheng]
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com> Link: https://lore.kernel.org/r/20240102214549.22498-2-quic_wcheng@quicinc.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: bea5892d0ed2 ("xhci: Limit time spent with xHC interrupts disabled during bus resume") Signed-off-by: Sasha Levin <sashal@kernel.org>
The current function that both removes and frees an interrupter isn't
optimal when using several interrupters. The array of interrupters need
to be protected with a lock while removing interrupters, but the default
xhci spin lock can't be used while freeing the interrupters event ring
segment table as dma_free_coherent() should be called with IRQs enabled.
There is no need to free the interrupter under the lock, so split this
code into separate unlocked free part, and a lock protected remove part.
Commit ebd88cf50729 ("xhci: Remove unused defines for ERST_SIZE and
ERST_ENTRIES") removed the ERST_SIZE macro but retained a code comment
explaining the quantity chosen in the macro.
Remove the code comment as well.
Signed-off-by: Lukas Wunner <lukas@wunner.de> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Link: https://lore.kernel.org/r/20231019102924.2797346-11-mathias.nyman@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: bea5892d0ed2 ("xhci: Limit time spent with xHC interrupts disabled during bus resume") Signed-off-by: Sasha Levin <sashal@kernel.org>
Users have reported log spam created by "Event Ring Full" xHC event
TRBs. These are caused by interrupt latency in conjunction with a very
busy set of devices on the bus. The errors are benign, but throughput
will suffer as the xHC will pause processing of transfers until the
Event Ring is drained by the kernel.
Commit dc0ffbea5729 ("usb: host: xhci: update event ring dequeue pointer
on purpose") mitigated the issue by advancing the Event Ring Dequeue
Pointer already after half a segment has been processed. Nevertheless,
providing a larger Event Ring would be useful to cope with load peaks.
Expand the number of event TRB slots available by increasing the number
of Event Ring segments in the ERST.
Controllers have a hardware-defined limit as to the number of ERST
entries they can process, but with up to 32k it can be excessively high
(sec 5.3.4). So cap the actual number at 2 (configurable through the
ERST_MAX_SEGS macro), which seems like a reasonable quantity. It is
supported by any xHC because the limit in the HCSPARAMS2 register is
defined as a power of 2. Renesas uPD720201 and VIA VL805 controllers
do not support more than 2 ERST entries.
An alternative to increasing the number of Event Ring segments would be
an increase of the segment size. But that requires allocating multiple
contiguous pages, which may be impossible if memory is fragmented.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com> Signed-off-by: Lukas Wunner <lukas@wunner.de> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Link: https://lore.kernel.org/r/20231019102924.2797346-6-mathias.nyman@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: bea5892d0ed2 ("xhci: Limit time spent with xHC interrupts disabled during bus resume") Signed-off-by: Sasha Levin <sashal@kernel.org>
When using more than one Event Ring segment (ERSTSZ > 1), software shall
set the DESI bits in the ERDP register to the number of the segment to
which the upper ERDP bits are pointing. The xHC may use the DESI bits
as a shortcut to determine whether it needs to check for an Event Ring
Full condition: If it's enqueueing events in a different segment, it
need not compare its internal Enqueue Pointer with the Dequeue Pointer
in the upper bits of the ERDP register (sec 5.5.2.3.3).
Not setting the DESI bits correctly can result in the xHC enqueueing
events past the Dequeue Pointer. On Renesas uPD720201 host controllers,
incorrect DESI bits cause an interrupt storm. For comparison, VIA VL805
host controllers do not exhibit such problems. Perhaps they do not take
advantage of the optimization afforded by the DESI bits.
To fix the issue, assign the segment number to each struct xhci_segment
in xhci_segment_alloc(). When advancing the Dequeue Pointer in
xhci_update_erst_dequeue(), write the segment number to the DESI bits.
On driver probe, set the DESI bits to zero in xhci_set_hc_event_deq() as
processing starts in segment 0. Likewise on driver teardown, clear the
DESI bits to zero in xhci_free_interrupter() when clearing the upper
bits of the ERDP register. Previously those functions (incorrectly)
treated the DESI bits as if they're declared RsvdP.
Signed-off-by: Lukas Wunner <lukas@wunner.de> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Link: https://lore.kernel.org/r/20231019102924.2797346-5-mathias.nyman@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: bea5892d0ed2 ("xhci: Limit time spent with xHC interrupts disabled during bus resume") Signed-off-by: Sasha Levin <sashal@kernel.org>
The patch does permit the offending YUV420 @ 59.94 phy_freq and
vclk_freq mode to match in calculations. It also results in all
fractional rates being unavailable for use. This was unintended
and requires the patch to be reverted.
Commit c7e73b5051d6 ("ARM: imx: mach-imx6ul: remove 14x14 EVK specific
PHY fixup") removed a PHY fixup that setted the clock mode and the LED
mode.
Make the Ethernet interface work again by doing as advised in the
commit's log, set clock mode and the LED mode in the device tree.
Completion of the FFA_PARTITION_INFO_GET ABI transfers the ownership of
the caller’s Rx buffer from the producer(typically partition mnager) to
the consumer(this driver/OS). FFA_RX_RELEASE transfers the ownership
from the consumer back to the producer.
However, when we set the flag to just return the count of partitions
deployed in the system corresponding to the specified UUID while
invoking FFA_PARTITION_INFO_GET, the Rx buffer ownership shouldn't be
transferred to this driver. We must be able to skip transferring back
the ownership to the partition manager when we request just to get the
count of the partitions as the buffers are not acquired in this case.
Firmware may return FFA_RET_DENIED or other error for the ffa_rx_release()
in such cases.
Using device_find_child() to lookup the proper SCMI device to destroy
causes an unbalance in device refcount, since device_find_child() calls an
implicit get_device(): this, in turns, inhibits the call of the provided
release methods upon devices destruction.
As a consequence, one of the structures that is not freed properly upon
destruction is the internal struct device_private dev->p populated by the
drivers subsystem core.
KMemleak detects this situation since loading/unloding some SCMI driver
causes related devices to be created/destroyed without calling any
device_release method.
est_qlen_notify() deletes its class from its active list with
list_del() when qlen is 0, therefore, it is not idempotent and
not friendly to its callers, like fq_codel_dequeue().
Let's make it idempotent to ease qdisc_tree_reduce_backlog() callers'
life. Also change other list_del()'s to list_del_init() just to be
extra safe.
Reported-by: Gerrard Tai <gerrard.tai@starlabs.sg> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Link: https://patch.msgid.link/20250403211033.166059-6-xiyou.wangcong@gmail.com Acked-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
qfq_qlen_notify() always deletes its class from its active list
with list_del_init() _and_ calls qfq_deactivate_agg() when the whole list
becomes empty.
To make it idempotent, just skip everything when it is not in the active
list.
Also change other list_del()'s to list_del_init() just to be extra safe.
Reported-by: Gerrard Tai <gerrard.tai@starlabs.sg> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://patch.msgid.link/20250403211033.166059-5-xiyou.wangcong@gmail.com Acked-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
hfsc_qlen_notify() is not idempotent either and not friendly
to its callers, like fq_codel_dequeue(). Let's make it idempotent
to ease qdisc_tree_reduce_backlog() callers' life:
1. update_vf() decreases cl->cl_nactive, so we can check whether it is
non-zero before calling it.
2. eltree_remove() always removes RB node cl->el_node, but we can use
RB_EMPTY_NODE() + RB_CLEAR_NODE() to make it safe.
Reported-by: Gerrard Tai <gerrard.tai@starlabs.sg> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://patch.msgid.link/20250403211033.166059-4-xiyou.wangcong@gmail.com Acked-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
drr_qlen_notify() always deletes the DRR class from its active list
with list_del(), therefore, it is not idempotent and not friendly
to its callers, like fq_codel_dequeue().
Let's make it idempotent to ease qdisc_tree_reduce_backlog() callers'
life. Also change other list_del()'s to list_del_init() just to be
extra safe.
Reported-by: Gerrard Tai <gerrard.tai@starlabs.sg> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://patch.msgid.link/20250403211033.166059-3-xiyou.wangcong@gmail.com Acked-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
htb_qlen_notify() always deactivates the HTB class and in fact could
trigger a warning if it is already deactivated. Therefore, it is not
idempotent and not friendly to its callers, like fq_codel_dequeue().
Let's make it idempotent to ease qdisc_tree_reduce_backlog() callers'
life.
Reported-by: Gerrard Tai <gerrard.tai@starlabs.sg> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://patch.msgid.link/20250403211033.166059-2-xiyou.wangcong@gmail.com Acked-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
OF: /sound: Read of boolean property 'simple-audio-card,bitclock-master' with a value.
OF: /sound: Read of boolean property 'simple-audio-card,frame-master' with a value.
or:
OF: /soc/sound@ec500000/ports/port@0/endpoint: Read of boolean property 'bitclock-master' with a value.
OF: /soc/sound@ec500000/ports/port@0/endpoint: Read of boolean property 'frame-master' with a value.
The use of of_property_read_bool() for non-boolean properties is
deprecated in favor of of_property_present() when testing for property
presence.
Replace testing for presence before calling of_property_read_u32() by
testing for an -EINVAL return value from the latter, to simplify the
code.
Use of_property_read_bool() to read boolean properties rather than
of_get_property(). This is part of a larger effort to remove callers
of of_get_property() and similar functions. of_get_property() leaks
the DT property data pointer which is a problem for dynamically
allocated nodes which may be freed.
Signed-off-by: Rob Herring (Arm) <robh@kernel.org> Link: https://patch.msgid.link/20240731191312.1710417-20-robh@kernel.org Signed-off-by: Mark Brown <broonie@kernel.org> Cc: Christophe Leroy <christophe.leroy@csgroup.eu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case the CMD_RTS got corrupted by interferences, the MSE102x
doesn't allow a retransmission of the command. Instead the Ethernet
frame must be shifted out of the SPI FIFO. Since the actual length is
unknown, assume the maximum possible value.
Fixes: 2f207cbf0dd4 ("net: vertexcom: Add MSE102x SPI support") Signed-off-by: Stefan Wahren <wahrenst@gmx.net> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://patch.msgid.link/20250430133043.7722-5-wahrenst@gmx.net Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Since there is no protection in the SPI protocol against electrical
interferences, the driver shouldn't blindly trust the length payload
of CMD_RTS. So introduce a bounds check for incoming frames.
Fixes: 2f207cbf0dd4 ("net: vertexcom: Add MSE102x SPI support") Signed-off-by: Stefan Wahren <wahrenst@gmx.net> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://patch.msgid.link/20250430133043.7722-4-wahrenst@gmx.net Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The MSE102x doesn't provide any SPI commands for interrupt handling.
So in case the interrupt fired before the driver requests the IRQ,
the interrupt will never fire again. In order to fix this always poll
for pending packets after opening the interface.
Fixes: 2f207cbf0dd4 ("net: vertexcom: Add MSE102x SPI support") Signed-off-by: Stefan Wahren <wahrenst@gmx.net> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://patch.msgid.link/20250430133043.7722-2-wahrenst@gmx.net Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently the ptp_clock_register() is called before relative
ptp resource ready. It may cause unexpected result when upper
layer called the ptp API during the timewindow. Fix it by
moving the ptp_clock_register() to the function end.
Fixes: 0bf5eb788512 ("net: hns3: add support for PTP") Signed-off-by: Jian Shen <shenjian15@huawei.com> Signed-off-by: Jijie Shao <shaojijie@huawei.com> Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev> Link: https://patch.msgid.link/20250430093052.2400464-5-shaojijie@huawei.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The size of the tm_qset file of debugfs is limited to 64 KB,
which is too small in the scenario with 1280 qsets.
The size needs to be expanded to 1 MB.
Fixes: 5e69ea7ee2a6 ("net: hns3: refactor the debugfs process") Signed-off-by: Hao Lan <lanhao@huawei.com> Signed-off-by: Peiyang Wang <wangpeiyang1@huawei.com> Signed-off-by: Jijie Shao <shaojijie@huawei.com> Link: https://patch.msgid.link/20250430093052.2400464-4-shaojijie@huawei.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When a VF is passthrough to a VM, and the VM is killed, the reported
interrupt may not been handled, it will remain, and won't be clear by
the nic engine even with a flr or tqp reset. When the VM restart, the
interrupt of the first vector may be dropped by the second enable_irq
in vfio, see the issue below:
https://gitlab.com/qemu-project/qemu/-/issues/2884#note_2423361621
We notice that the vfio has always behaved this way, and the interrupt
is a residue of the nic engine, so we fix the problem by moving the
vector enable process out of the enable_irq loop.
The VF driver missed to store the rx VLAN tag strip state when
user change the rx VLAN tag offload state. And it will default
to enable the rx vlan tag strip when re-init VF device after
reset. So if user disable rx VLAN tag offload, and trig reset,
then the HW will still strip the VLAN tag from packet nad fill
into RX BD, but the VF driver will ignore it for rx VLAN tag
offload disabled. It may cause the rx VLAN tag dropped.
Fixes: b2641e2ad456 ("net: hns3: Add support of hardware rx-vlan-offload to HNS3 VF driver") Signed-off-by: Jian Shen <shenjian15@huawei.com> Signed-off-by: Jijie Shao <shaojijie@huawei.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://patch.msgid.link/20250430093052.2400464-2-shaojijie@huawei.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When the host loses heartbeat messages from the device,
the driver calls the device-specific ndo_stop function,
which frees the resources. If the driver is unloaded in
this scenario, it calls ndo_stop again, attempting to free
resources that have already been freed, leading to a host
hang issue. To resolve this, dev_close should be called
instead of the device-specific stop function.dev_close
internally calls ndo_stop to stop the network interface
and performs additional cleanup tasks. During the driver
unload process, if the device is already down, ndo_stop
is not called.
Fixes: 5cb96c29aa0e ("octeon_ep: add heartbeat monitor") Signed-off-by: Sathesh B Edara <sedara@marvell.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://patch.msgid.link/20250429114624.19104-1-sedara@marvell.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Activate TX hang workaround also in
fec_enet_txq_submit_skb() when TSO is not enabled.
Errata: ERR007885
Symptoms: NETDEV WATCHDOG: eth0 (fec): transmit queue 0 timed out
commit 37d6017b84f7 ("net: fec: Workaround for imx6sx enet tx hang when enable three queues")
There is a TDAR race condition for mutliQ when the software sets TDAR
and the UDMA clears TDAR simultaneously or in a small window (2-4 cycles).
This will cause the udma_tx and udma_tx_arbiter state machines to hang.
So, the Workaround is checking TDAR status four time, if TDAR cleared by
hardware and then write TDAR, otherwise don't set TDAR.
Fixes: 53bb20d1faba ("net: fec: add variable reg_desc_active to speed things up") Signed-off-by: Mattias Barthel <mattias.barthel@atlascopco.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://patch.msgid.link/20250429090826.3101258-1-mattiasbarthel@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Always map the `skb` to the LS descriptor. Previously skb was
mapped to EXT descriptor when the number of fragments is zero with
GSO enabled. Mapping the skb to EXT descriptor prevents it from
being freed, leading to a memory leak
Fixes: 23f0703c125b ("lan743x: Add main source files for new lan743x driver") Signed-off-by: Thangaraj Samynathan <thangaraj.s@microchip.com> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Link: https://patch.msgid.link/20250429052527.10031-1-thangaraj.s@microchip.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
This patch addresses a data corruption issue observed in nvme-tcp during
testing.
In an NVMe native multipath setup, when an I/O timeout occurs, all
inflight I/Os are canceled almost immediately after the kernel socket is
shut down. These canceled I/Os are reported as host path errors,
triggering a failover that succeeds on a different path.
However, at this point, the original I/O may still be outstanding in the
host's network transmission path (e.g., the NIC’s TX queue). From the
user-space app's perspective, the buffer associated with the I/O is
considered completed since they're acked on the different path and may
be reused for new I/O requests.
Because nvme-tcp enables zero-copy by default in the transmission path,
this can lead to corrupted data being sent to the original target,
ultimately causing data corruption.
We can reproduce this data corruption by injecting delay on one path and
triggering i/o timeout.
To prevent this issue, this change ensures that all inflight
transmissions are fully completed from host's perspective before
returning from queue stop. To handle concurrent I/O timeout from multiple
namespaces under the same controller, always wait in queue stop
regardless of queue's state.
This aligns with the behavior of queue stopping in other NVMe fabric
transports.
Fixes: 3f2304f8c6d6 ("nvme-tcp: add NVMe over TCP host driver") Signed-off-by: Michael Liang <mliang@purestorage.com> Reviewed-by: Mohamed Khalfella <mkhalfella@purestorage.com> Reviewed-by: Randy Jennings <randyj@purestorage.com> Reviewed-by: Sagi Grimberg <sagi@grimberg.me> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
For version 1 register dump that includes the PCIe stats, the existing
code incorrectly assumes that all PCIe stats are 64-bit values. Fix it
by using an array containing the starting and ending index of the 32-bit
values. The loop in bnxt_get_regs() will use the array to do proper
endian swap for the 32-bit values.
Fixes: b5d600b027eb ("bnxt_en: Add support for 'ethtool -d'") Reviewed-by: Shruti Parab <shruti.parab@broadcom.com> Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com> Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
This happens when copying the coredump segment list in
bnxt_hwrm_dbg_dma_data() with the HWRM_DBG_COREDUMP_LIST FW command.
The info->dest_buf buffer is allocated based on the number of coredump
segments returned by the FW. The segment list is then DMA'ed by
the FW and the length of the DMA is returned by FW. The driver then
copies this DMA'ed segment list to info->dest_buf.
In some cases, this DMA length may exceed the info->dest_buf length
and cause the above BUG condition. Fix it by capping the copy
length to not exceed the length of info->dest_buf. The extra
DMA data contains no useful information.
This code path is shared for the HWRM_DBG_COREDUMP_LIST and the
HWRM_DBG_COREDUMP_RETRIEVE FW commands. The buffering is different
for these 2 FW commands. To simplify the logic, we need to move
the line to adjust the buffer length for HWRM_DBG_COREDUMP_RETRIEVE
up, so that the new check to cap the copy length will work for both
commands.
Fixes: c74751f4c392 ("bnxt_en: Return error if FW returns more data than dump length") Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com> Signed-off-by: Shruti Parab <shruti.parab@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
When handling HWRM_DBG_COREDUMP_LIST FW command in
bnxt_hwrm_dbg_dma_data(), the allocated buffer info->dest_buf is
not freed in the error path. In the normal path, info->dest_buf
is assigned to coredump->data and it will eventually be freed after
the coredump is collected.
Free info->dest_buf immediately inside bnxt_hwrm_dbg_dma_data() in
the error path.
Fixes: c74751f4c392 ("bnxt_en: Return error if FW returns more data than dump length") Reported-by: Michael Chan <michael.chan@broadcom.com> Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com> Signed-off-by: Shruti Parab <shruti.parab@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Simplest setup to reproduce the issue: connect 2 ports of the
LS1028A-RDB together (eno0 with swp0) and run:
$ ip link set eno0 up && ip link set swp0 up
$ tc qdisc replace dev swp0 parent root handle 100 taprio num_tc 8 \
queues 1@0 1@1 1@2 1@3 1@4 1@5 1@6 1@7 map 0 1 2 3 4 5 6 7 \
base-time 0 sched-entry S 20 300000 sched-entry S 10 200000 \
sched-entry S 20 300000 sched-entry S 48 200000 \
sched-entry S 20 300000 sched-entry S 83 200000 \
sched-entry S 40 300000 sched-entry S 00 200000 flags 2
$ ptp4l -i eno0 -f /etc/linuxptp/configs/gPTP.cfg -m &
$ ptp4l -i swp0 -f /etc/linuxptp/configs/gPTP.cfg -m
One will observe that the PTP state machine on swp0 starts
synchronizing, then it attempts to do a clock step, and after that, it
never fails to recover from the condition below.
ptp4l[82.427]: selected best master clock 00049f.fffe.05f627
ptp4l[82.428]: port 1 (swp0): MASTER to UNCALIBRATED on RS_SLAVE
ptp4l[83.252]: port 1 (swp0): UNCALIBRATED to SLAVE on MASTER_CLOCK_SELECTED
ptp4l[83.886]: rms 4537731277 max 9075462553 freq -18518 +/- 11467 delay 818 +/- 0
ptp4l[84.170]: timed out while polling for tx timestamp
ptp4l[84.171]: increasing tx_timestamp_timeout or increasing kworker priority may correct this issue, but a driver bug likely causes it
ptp4l[84.172]: port 1 (swp0): send peer delay request failed
ptp4l[84.173]: port 1 (swp0): clearing fault immediately
ptp4l[84.269]: port 1 (swp0): SLAVE to LISTENING on INIT_COMPLETE
ptp4l[85.303]: timed out while polling for tx timestamp
ptp4l[84.171]: increasing tx_timestamp_timeout or increasing kworker priority may correct this issue, but a driver bug likely causes it
ptp4l[84.172]: port 1 (swp0): send peer delay request failed
ptp4l[84.173]: port 1 (swp0): clearing fault immediately
ptp4l[84.269]: port 1 (swp0): SLAVE to LISTENING on INIT_COMPLETE
ptp4l[85.303]: timed out while polling for tx timestamp
ptp4l[85.304]: increasing tx_timestamp_timeout or increasing kworker priority may correct this issue, but a driver bug likely causes it
ptp4l[85.305]: port 1 (swp0): send peer delay response failed
ptp4l[85.306]: port 1 (swp0): clearing fault immediately
ptp4l[86.304]: timed out while polling for tx timestamp
A hint is given by the non-zero statistics for dropped packets which
were expecting hardware TX timestamps:
We know that when PTP clock stepping takes place (from ocelot_ptp_settime64()
or from ocelot_ptp_adjtime()), vsc9959_tas_clock_adjust() is called.
Another interesting hint is that placing an early return in
vsc9959_tas_clock_adjust(), so as to neutralize this function, fixes the
issue and TX timestamps are no longer dropped.
The debugging function written by me and included below is intended to
read the GCL RAM, after the admin schedule became operational, through
the two status registers available for this purpose:
QSYS_GCL_STATUS_REG_1 and QSYS_GCL_STATUS_REG_2.
static void vsc9959_print_tas_gcl(struct ocelot *ocelot)
{
u32 val, list_length, interval, gate_state;
int i, err;
err = read_poll_timeout(ocelot_read, val,
!(val & QSYS_PARAM_STATUS_REG_8_CONFIG_PENDING),
10, 100000, false, ocelot, QSYS_PARAM_STATUS_REG_8);
if (err) {
dev_err(ocelot->dev,
"Failed to wait for TAS config pending bit to clear: %pe\n",
ERR_PTR(err));
return;
}
val = ocelot_read(ocelot, QSYS_PARAM_STATUS_REG_3);
list_length = QSYS_PARAM_STATUS_REG_3_LIST_LENGTH_X(val);
for (i = 0; i < list_length; i++) {
ocelot_rmw(ocelot,
QSYS_GCL_STATUS_REG_1_GCL_ENTRY_NUM(i),
QSYS_GCL_STATUS_REG_1_GCL_ENTRY_NUM_M,
QSYS_GCL_STATUS_REG_1);
interval = ocelot_read(ocelot, QSYS_GCL_STATUS_REG_2);
val = ocelot_read(ocelot, QSYS_GCL_STATUS_REG_1);
gate_state = QSYS_GCL_STATUS_REG_1_GATE_STATE_X(val);
dev_info(ocelot->dev, "GCL entry %d: states 0x%x interval %u\n",
i, gate_state, interval);
}
}
Calling it from two places: after the initial QSYS_TAS_PARAM_CFG_CTRL_CONFIG_CHANGE
performed by vsc9959_qos_port_tas_set(), and after the one done by
vsc9959_tas_clock_adjust(), I notice the following difference.
From the tc-taprio process context, where the schedule was initially
configured, the GCL looks like this:
mscc_felix 0000:00:00.5: GCL length: 8
mscc_felix 0000:00:00.5: GCL entry 0: states 0x20 interval 300000
mscc_felix 0000:00:00.5: GCL entry 1: states 0x10 interval 200000
mscc_felix 0000:00:00.5: GCL entry 2: states 0x20 interval 300000
mscc_felix 0000:00:00.5: GCL entry 3: states 0x48 interval 200000
mscc_felix 0000:00:00.5: GCL entry 4: states 0x20 interval 300000
mscc_felix 0000:00:00.5: GCL entry 5: states 0x83 interval 200000
mscc_felix 0000:00:00.5: GCL entry 6: states 0x40 interval 300000
mscc_felix 0000:00:00.5: GCL entry 7: states 0x0 interval 200000
But from the ptp4l clock stepping process context, when the
vsc9959_tas_clock_adjust() hook is called, the GCL RAM of the
operational schedule now looks like this:
mscc_felix 0000:00:00.5: GCL length: 8
mscc_felix 0000:00:00.5: GCL entry 0: states 0x0 interval 0
mscc_felix 0000:00:00.5: GCL entry 1: states 0x0 interval 0
mscc_felix 0000:00:00.5: GCL entry 2: states 0x0 interval 0
mscc_felix 0000:00:00.5: GCL entry 3: states 0x0 interval 0
mscc_felix 0000:00:00.5: GCL entry 4: states 0x0 interval 0
mscc_felix 0000:00:00.5: GCL entry 5: states 0x0 interval 0
mscc_felix 0000:00:00.5: GCL entry 6: states 0x0 interval 0
mscc_felix 0000:00:00.5: GCL entry 7: states 0x0 interval 0
I do not have a formal explanation, just experimental conclusions.
It appears that after triggering QSYS_TAS_PARAM_CFG_CTRL_CONFIG_CHANGE
for a port's TAS, the GCL entry RAM is updated anyway, despite what the
documentation claims: "Specify the time interval in
QSYS::GCL_CFG_REG_2.TIME_INTERVAL. This triggers the actual RAM
write with the gate state and the time interval for the entry number
specified". We don't touch that register (through vsc9959_tas_gcl_set())
from vsc9959_tas_clock_adjust(), yet the GCL RAM is updated anyway.
It seems to be updated with effectively stale memory, which in my
testing can hold a variety of things, including even pieces of the
previously applied schedule, for particular schedule lengths.
As such, in most circumstances it is very difficult to pinpoint this
issue, because the newly updated schedule would "behave strangely",
but ultimately might still pass traffic to some extent, due to some
gate entries still being present in the stale GCL entry RAM. It is easy
to miss.
With the particular schedule given at the beginning, the GCL RAM
"happens" to be reproducibly rewritten with all zeroes, and this is
consistent with what we see: when the time-aware shaper has gate entries
with all gates closed, traffic is dropped on TX, no wonder we can't
retrieve TX timestamps.
Rewriting the GCL entry RAM when reapplying the new base time fixes the
observed issue.
Fixes: 8670dc33f48b ("net: dsa: felix: update base time of time-aware shaper when adjusting PTP time") Reported-by: Richie Pearn <richard.pearn@nxp.com> Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Link: https://patch.msgid.link/20250426144859.3128352-2-vladimir.oltean@nxp.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
If the mtk_poll_rx() function detects the MTK_RESETTING flag, it will
jump to release_desc and refill the high word of the SDP on the 4GB RFB.
Subsequently, mtk_rx_clean will process an incorrect SDP, leading to a
panic.
Commit 1a931c4f5e68 ("igc: add lock preventing multiple simultaneous PTM
transactions") added a new mutex to protect concurrent PTM transactions.
This lock is acquired in igc_ptp_reset() in order to ensure the PTM
registers are properly disabled after a device reset.
The flow where the lock is acquired already holds a spinlock, so acquiring
a mutex leads to a sleep-while-locking bug, reported both by smatch,
and the kernel test robot.
The critical section in igc_ptp_reset() does correctly use the
readx_poll_timeout_atomic variants, but the standard PTM flow uses regular
sleeping variants. This makes converting the mutex to a spinlock a bit
tricky.
Instead, re-order the locking in igc_ptp_reset. Acquire the mutex first,
and then the tmreg_lock spinlock. This is safe because there is no other
ordering dependency on these locks, as this is the only place where both
locks were acquired simultaneously. Indeed, any other flow acquiring locks
in that order would be wrong regardless.
This bit is necessary to receive packets from the internal PHY.
Without this bit set, no activity occurs on the interface.
Normally u-boot sets this bit, but if u-boot is compiled without
net support, the interface will be up but without any activity.
If bit is set once, it will work until the IP is powered down or reset.
The vendor SDK sets this bit along with the PHY_ID bits.
As it's name suggests, parse_eeprom() parses EEPROM data.
This is done by reading data, 16 bits at a time as follows:
for (i = 0; i < 128; i++)
((__le16 *) sromdata)[i] = cpu_to_le16(read_eeprom(np, i));
sromdata is at the same memory location as psrom.
And the type of psrom is a pointer to struct t_SROM.
As can be seen in the loop above, data is stored in sromdata, and thus psrom,
as 16-bit little-endian values.
However, the integer fields of t_SROM are host byte order integers.
And in the case of led_mode this leads to a little endian value
being incorrectly treated as host byte order.
Looking at rio_set_led_mode, this does appear to be a bug as that code
masks led_mode with 0x1, 0x2 and 0x8. Logic that would be effected by a
reversed byte order.
This problem would only manifest on big endian hosts.
Found by inspection while investigating a sparse warning
regarding the crc field of t_SROM.
I believe that warning is a false positive. And although I plan
to send a follow-up to use little-endian types for other the integer
fields of PSROM_t I do not believe that will involve any bug fixes.
A zero return means the reset was successfully scheduled. We don't want
to unquiesce the queues while the reset_work is pending, as that will
just flush out requeued requests to a failed completion.
Fixes: 71a5bb153be104 ("nvme: ensure disabling pairs with unquiesce") Reported-by: Dhankaran Singh Ajravat <dhankaran@meta.com> Signed-off-by: Keith Busch <kbusch@kernel.org> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
The conversion function from MIDI 1.0 to UMP packet contains an
internal buffer to keep the incoming MIDI bytes, and its size is 4, as
it was supposed to be the max size for a MIDI1 UMP packet data.
However, the implementation overlooked that SysEx is handled in a
different format, and it can be up to 6 bytes, as found in
do_convert_to_ump(). It leads eventually to a buffer overflow, and
may corrupt the memory when a longer SysEx message is received.
The fix is simply to extend the buffer size to 6 to fit with the SysEx
UMP message.
As mentioned in the commit baeb705fd6a7 ("ice: always check VF VSI
pointer values"), we need to perform a null pointer check on the return
value of ice_get_vf_vsi() before using it.
Fixes: 6ebbe97a4881 ("ice: Add a per-VF limit on number of FDIR filters") Signed-off-by: Xuanqiang Luo <luoxuanqiang@kylinos.cn> Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com> Reviewed-by: Simon Horman <horms@kernel.org> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Link: https://patch.msgid.link/20250425222636.3188441-3-anthony.l.nguyen@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
As described in Gerrard's report [1], there are use cases where a netem
child qdisc will make the parent qdisc's enqueue callback reentrant.
In the case of qfq, there won't be a UAF, but the code will add the same
classifier to the list twice, which will cause memory corruption.
This patch checks whether the class was already added to the agg->active
list (cl_is_active) before doing the addition to cater for the reentrant
case.
As described in Gerrard's report [1], there are use cases where a netem
child qdisc will make the parent qdisc's enqueue callback reentrant.
In the case of ets, there won't be a UAF, but the code will add the same
classifier to the list twice, which will cause memory corruption.
In addition to checking for qlen being zero, this patch checks whether
the class was already added to the active_list (cl_is_active) before
doing the addition to cater for the reentrant case.
As described in Gerrard's report [1], we have a UAF case when an hfsc class
has a netem child qdisc. The crux of the issue is that hfsc is assuming
that checking for cl->qdisc->q.qlen == 0 guarantees that it hasn't inserted
the class in the vttree or eltree (which is not true for the netem
duplicate case).
This patch checks the n_active class variable to make sure that the code
won't insert the class in the vttree or eltree twice, catering for the
reentrant case.
As described in Gerrard's report [1], there are use cases where a netem
child qdisc will make the parent qdisc's enqueue callback reentrant.
In the case of drr, there won't be a UAF, but the code will add the same
classifier to the list twice, which will cause memory corruption.
In addition to checking for qlen being zero, this patch checks whether the
class was already added to the active_list (cl_is_active) before adding
to the list to cover for the reentrant case.
The actual device uninit usually happens on a separate thread
scheduled after this code runs, but there is no guarantee of order
of thread execution, so this could be a problem. There's no
actual need to clear the client_id at this point, so simply
remove the offending code.
Fixes: 10659034c622 ("pds_core: add the aux client API") Signed-off-by: Shannon Nelson <shannon.nelson@amd.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://patch.msgid.link/20250425203857.71547-1-shannon.nelson@amd.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In preparation for adding a new auxiliary_device for the PF,
make the vif type an argument to pdsc_auxbus_dev_add(). Pass in
the address of the padev pointer so that the caller can specify
where to save it and keep the mutex usage within the function.
Link: https://patch.msgid.link/r/20250320194412.67983-3-shannon.nelson@amd.com Reviewed-by: Leon Romanovsky <leonro@nvidia.com> Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Reviewed-by: Dave Jiang <dave.jiang@intel.com> Signed-off-by: Shannon Nelson <shannon.nelson@amd.com> Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Stable-dep-of: dfd76010f8e8 ("pds_core: remove write-after-free of client_id") Signed-off-by: Sasha Levin <sashal@kernel.org>
When the VF is hit with a reset, remove the aux device in
the prepare for reset and try to restore it after the reset.
The userland mechanics will need to recover and rebuild whatever
uses the device afterwards.
Reviewed-by: Brett Creeley <brett.creeley@amd.com> Signed-off-by: Shannon Nelson <shannon.nelson@amd.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: dfd76010f8e8 ("pds_core: remove write-after-free of client_id") Signed-off-by: Sasha Levin <sashal@kernel.org>
Similar to what we do in the AdminQ, check for devcmd health
while waiting for an answer.
Signed-off-by: Shannon Nelson <shannon.nelson@amd.com> Reviewed-by: Brett Creeley <brett.creeley@amd.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: dfd76010f8e8 ("pds_core: remove write-after-free of client_id") Signed-off-by: Sasha Levin <sashal@kernel.org>
In mtk_star_rx_poll function, on event processing completion, the
mtk_star_emac driver calls napi_complete_done but ignores its return
code and enable RX DMA interrupts inconditionally. This return code
gives the info if a device should avoid rearming its interrupts or not,
so fix this behaviour by taking it into account.
Use spin_lock_irqsave and spin_unlock_irqrestore instead of spin_lock
and spin_unlock in mtk_star_emac driver to avoid spinlock recursion
occurrence that can happen when enabling the DMA interrupts again in
rx/tx poll.
ip link add br0 type bridge vlan_filtering 1 # vlan_default_pvid 1 is implicit
ip link set swp0 master br0
bridge vlan add dev swp0 vid 1
should result in the dropping of untagged and 802.1p-tagged traffic, but
we see that it continues to be accepted. Whereas, had we deleted VID 1
instead, the aforementioned dropping would have worked
This is because the ANA_PORT_DROP_CFG update logic doesn't run, because
ocelot_vlan_add() only calls ocelot_port_set_pvid() if the new VLAN has
the BRIDGE_VLAN_INFO_PVID flag.
Similar to other drivers like mt7530_port_vlan_add() which handle this
case correctly, we need to test whether the VLAN we're changing used to
have the BRIDGE_VLAN_INFO_PVID flag, but lost it now. That amounts to a
PVID deletion and should be treated as such.
Regarding blame attribution: this never worked properly since the
introduction of bridge VLAN filtering in commit 7142529f1688 ("net:
mscc: ocelot: add VLAN filtering"). However, there was a significant
paradigm shift which aligned the ANA_PORT_DROP_CFG register with the
PVID concept rather than with the native VLAN concept, and that change
wasn't targeted for 'stable'. Realistically, that is as far as this fix
needs to be propagated to.
Fixes: be0576fed6d3 ("net: mscc: ocelot: move the logic to drop 802.1p traffic to the pvid deletion") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Link: https://patch.msgid.link/20250424223734.3096202-1-vladimir.oltean@nxp.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
I was revisiting the topic of 802.1ad treatment in the Ocelot switch [0]
and realized that not only is its basic VLAN classification pipeline
improper for offloading vlan_protocol 802.1ad bridges, but also improper
for offloading regular 802.1Q bridges already.
Namely, 802.1ad-tagged traffic should be treated as VLAN-untagged by
bridged ports, but this switch treats it as if it was 802.1Q-tagged with
the same VID as in the 802.1ad header. This is markedly different to
what the Linux bridge expects; see the "other_tpid()" function in
tools/testing/selftests/net/forwarding/bridge_vlan_aware.sh.
An idea came to me that the VCAP IS1 TCAM is more powerful than I'm
giving it credit for, and that it actually overwrites the classified VID
before the VLAN Table lookup takes place. In other words, it can be
used even to save a packet from being dropped on ingress due to VLAN
membership.
Add a sophisticated TCAM rule hardcoded into the driver to force the
switch to behave like a Linux bridge with vlan_filtering 1 vlan_protocol
802.1Q.
Regarding the lifetime of the filter: eventually the bridge will
disappear, and vlan_filtering on the port will be restored to 0 for
standalone mode. Then the filter will be deleted.
Fixes: 7142529f1688 ("net: mscc: ocelot: add VLAN filtering") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: 5ec6d7d737a4 ("net: mscc: ocelot: delete PVID VLAN when readding it as non-PVID") Signed-off-by: Sasha Levin <sashal@kernel.org>
mono_delivery_time was added to check if skb->tstamp has delivery
time in mono clock base (i.e. EDT) otherwise skb->tstamp has
timestamp in ingress and delivery_time at egress.
Renaming the bitfield from mono_delivery_time to tstamp_type is for
extensibilty for other timestamps such as userspace timestamp
(i.e. SO_TXTIME) set via sock opts.
As we are renaming the mono_delivery_time to tstamp_type, it makes
sense to start assigning tstamp_type based on enum defined
in this commit.
Earlier we used bool arg flag to check if the tstamp is mono in
function skb_set_delivery_time, Now the signature of the functions
accepts tstamp_type to distinguish between mono and real time.
Also skb_set_delivery_type_by_clockid is a new function which accepts
clockid to determine the tstamp_type.
In future tstamp_type:1 can be extended to support userspace timestamp
by increasing the bitfield.
Signed-off-by: Abhishek Chauhan <quic_abchauha@quicinc.com> Reviewed-by: Willem de Bruijn <willemb@google.com> Reviewed-by: Martin KaFai Lau <martin.lau@kernel.org> Link: https://lore.kernel.org/r/20240509211834.3235191-2-quic_abchauha@quicinc.com Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
Stable-dep-of: 3908feb1bd7f ("Bluetooth: L2CAP: copy RX timestamp to new fragments") Signed-off-by: Sasha Levin <sashal@kernel.org>
The issue stems from handle_dump_pkt_qca() returning 0 even when a dump
packet is successfully processed. This is because it incorrectly
forwards the return value of hci_devcd_init() (which returns 0 on
success). As a result, the caller (btusb_recv_acl_qca() or
btusb_recv_evt_qca()) assumes the packet was not handled and passes it
to hci_recv_frame(), leading to premature kfree() of the skb.
Later, hci_devcd_rx() attempts to dequeue the same skb from the dump
queue, resulting in a NULL pointer dereference.
Fix this by:
1. Making handle_dump_pkt_qca() return 0 on success and negative errno
on failure, consistent with kernel conventions.
2. Splitting dump packet detection into separate functions for ACL
and event packets for better structure and readability.
This ensures dump packets are properly identified and consumed, avoiding
double handling and preventing NULL pointer access.
The cited commit assumes enabling roce always succeeds. But it is
not true. Add error handling for it.
Fixes: 80f09dfc237f ("net/mlx5: Eswitch, enable RoCE loopback traffic") Signed-off-by: Chris Mi <cmi@nvidia.com> Reviewed-by: Roi Dayan <roid@nvidia.com> Reviewed-by: Maor Gottlieb <maorg@nvidia.com> Signed-off-by: Mark Bloch <mbloch@nvidia.com> Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com> Link: https://patch.msgid.link/20250423083611.324567-6-mbloch@nvidia.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / thirdparty / kernel / stable.git / log
