Setting up the timing engine when the physical encoder has a split role
neglects dividing the drm_display_mode's hskew parameter. Let's fix this
since this must also be done in preparation for implementing YUV420 over
DP.
Running event hv_gpci/dispatch_timebase_by_processor_processor_time_in_timebase_cycles,phys_processor_idx=0/
in one of the system throws below error:
---Logs---
# perf list | grep hv_gpci/dispatch_timebase_by_processor_processor_time_in_timebase_cycles
hv_gpci/dispatch_timebase_by_processor_processor_time_in_timebase_cycles,phys_processor_idx=?/[Kernel PMU event]
# perf stat -v -e hv_gpci/dispatch_timebase_by_processor_processor_time_in_timebase_cycles,phys_processor_idx=0/ sleep 2
Using CPUID 00800200
Control descriptor is not initialized
Warning:
hv_gpci/dispatch_timebase_by_processor_processor_time_in_timebase_cycles,phys_processor_idx=0/ event is not supported by the kernel.
failed to read counter hv_gpci/dispatch_timebase_by_processor_processor_time_in_timebase_cycles,phys_processor_idx=0/
The above error is because of the hcall failure as required
permission "Enable Performance Information Collection" is not set.
Based on current code, single_gpci_request function did not check the
error type incase hcall fails and by default returns EINVAL. But we can
have other reasons for hcall failures like H_AUTHORITY/H_PARAMETER with
detail_rc as GEN_BUF_TOO_SMALL, for which we need to act accordingly.
Fix this issue by adding new checks in the single_gpci_request and
h_gpci_event_init functions.
Result after fix patch changes:
# perf stat -e hv_gpci/dispatch_timebase_by_processor_processor_time_in_timebase_cycles,phys_processor_idx=0/ sleep 2
Error:
No permission to enable hv_gpci/dispatch_timebase_by_processor_processor_time_in_timebase_cycles,phys_processor_idx=0/ event.
Fixes: 220a0c609ad1 ("powerpc/perf: Add support for the hv gpci (get performance counter info) interface") Reported-by: Akanksha J N <akanksha@linux.ibm.com> Signed-off-by: Kajol Jain <kjain@linux.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://msgid.link/20240229122847.101162-1-kjain@linux.ibm.com Signed-off-by: Sasha Levin <sashal@kernel.org>
It's possible that mtk_crtc->event is NULL in
mtk_drm_crtc_finish_page_flip().
pending_needs_vblank value is set by mtk_crtc->event, but in
mtk_drm_crtc_atomic_flush(), it's is not guarded by the same
lock in mtk_drm_finish_page_flip(), thus a race condition happens.
Consider the following case:
CPU1 CPU2
step 1:
mtk_drm_crtc_atomic_begin()
mtk_crtc->event is not null,
step 1:
mtk_drm_crtc_atomic_flush:
mtk_drm_crtc_update_config(
!!mtk_crtc->event)
step 2:
mtk_crtc_ddp_irq ->
mtk_drm_finish_page_flip:
lock
mtk_crtc->event set to null,
pending_needs_vblank set to false
unlock
pending_needs_vblank set to true,
step 2:
mtk_crtc_ddp_irq ->
mtk_drm_finish_page_flip called again,
pending_needs_vblank is still true
//null pointer
Instead of guarding the entire mtk_drm_crtc_atomic_flush(), it's more
efficient to just check if mtk_crtc->event is null before use.
When saa7146_register_device and saa7146_vv_init fails, budget_av_attach
should free the resources it allocates, like the error-handling of
ttpci_budget_init does. Besides, there are two fixme comment refers to
such deallocations.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Zhipeng Lu <alexious@zju.edu.cn> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Sasha Levin <sashal@kernel.org>
A previous patch worked around a KASAN issue in stv0367, now a similar
problem showed up with clang:
drivers/media/dvb-frontends/stv0367.c:1222:12: error: stack frame size (3624) exceeds limit (2048) in 'stv0367ter_set_frontend' [-Werror,-Wframe-larger-than]
1214 | static int stv0367ter_set_frontend(struct dvb_frontend *fe)
Rework the stv0367_writereg() function to be simpler and mark both
register access functions as noinline_for_stack so the temporary
i2c_msg structures do not get duplicated on the stack when KASAN_STACK
is enabled.
[Syzbot reported]
BUG: KASAN: slab-use-after-free in pvr2_context_set_notify+0x2c4/0x310 drivers/media/usb/pvrusb2/pvrusb2-context.c:35
Read of size 4 at addr ffff888113aeb0d8 by task kworker/1:1/26
[Analyze]
Task A set disconnect_flag = !0, which resulted in Task B's condition being met
and releasing mp, leading to this issue.
[Fix]
Place the disconnect_flag assignment operation after all code in pvr2_context_disconnect()
to avoid this issue.
Reported-and-tested-by: syzbot+ce750e124675d4599449@syzkaller.appspotmail.com Fixes: e5be15c63804 ("V4L/DVB (7711): pvrusb2: Fix race on module unload") Signed-off-by: Edward Adam Davis <eadavis@qq.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Sasha Levin <sashal@kernel.org>
Missing break statement in the ATOM_ARG_IMM case of a switch statement,
adds the missing break statement, ensuring that the program's control
flow is as intended.
Fixes the below:
drivers/gpu/drm/amd/amdgpu/atom.c:323 atom_get_src_int() warn: ignoring unreachable code.
Fixes: d38ceaf99ed0 ("drm/amdgpu: add core driver (v4)") Cc: Jammy Zhou <Jammy.Zhou@amd.com> Cc: Christian König <christian.koenig@amd.com> Cc: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
According to Amlogic datasheets for the SoCs supported by this driver, the
maximum bit clock rate is 100MHz.
The tdm interface allows the rates listed by the DAI driver, regardless of
the number slots or their width. However, these will impact the bit clock
rate.
Hitting the 100MHz limit is very unlikely for most use cases but it is
possible.
For example with 32 slots / 32 bits wide, the maximum rate is no longer
384kHz but ~96kHz.
Add the constraint accordingly if the component is not already active.
If it is active, the rate is already constrained by the first stream rate.
By default, when mclk-fs is not provided, the tdm-interface driver
requests an MCLK that is 4x the bit clock, SCLK.
However there is no justification for this:
* If the codec needs MCLK for its operation, mclk-fs is expected to be set
according to the codec requirements.
* If the codec does not need MCLK the minimum is 2 * SCLK, because this is
minimum the divider between SCLK and MCLK can do.
Multiplying by 4 may cause problems because the PLL limit may be reached
sooner than it should, so use 2x instead.
mtd-ram can potentially be larger than 4GB. get_bitmask_order() uses
fls() that is not guaranteed to work with values larger than 32-bit.
Specifically on aarch64 fls() returns 0 when all 32 LSB bits are clear.
Use fls64() instead.
When the driver sets up the zpos property it sets the default zpos value
to the HW id of the plane. That is fine as such, but as on many DSS
versions the driver arranges the DRM planes in a different order than
the HW planes (to keep the non-scalable planes first), this leads to odd
initial zpos values. An example is J721e, where the initial zpos values
for DRM planes are 1, 3, 0, 2.
In theory the userspace should configure the zpos values properly when
using multiple planes, and in that sense the initial zpos values
shouldn't matter, but there's really no reason not to fix this and help
the userspace apps which don't handle zpos perfectly. In particular,
some versions of Weston seem to have issues dealing with the planes
with the current default zpos values.
So let's change the zpos values for the DRM planes to 0, 1, 2, 3.
Another option would be to configure the planes marked as primary planes
to zpos 0. On a two display system this would give us plane zpos values
of 0, 0, 1, 2. The end result and behavior would be very similar in this
option, and I'm not aware that this would actually help us in any way.
So, to keep the code simple, I opted for the 0, 1, 2, 3 values.
clang-16 warns about casting between incompatible function types:
arch/arm/crypto/sha256_glue.c:37:5: error: cast from 'void (*)(u32 *, const void *, unsigned int)' (aka 'void (*)(unsigned int *, const void *, unsigned int)') to 'sha256_block_fn *' (aka 'void (*)(struct sha256_state *, const unsigned char *, int)') converts to incompatible function type [-Werror,-Wcast-function-type-strict]
37 | (sha256_block_fn *)sha256_block_data_order);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
arch/arm/crypto/sha512-glue.c:34:3: error: cast from 'void (*)(u64 *, const u8 *, int)' (aka 'void (*)(unsigned long long *, const unsigned char *, int)') to 'sha512_block_fn *' (aka 'void (*)(struct sha512_state *, const unsigned char *, int)') converts to incompatible function type [-Werror,-Wcast-function-type-strict]
34 | (sha512_block_fn *)sha512_block_data_order);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Fix the prototypes for the assembler functions to match the typedef.
The code already relies on the digest being the first part of the
state structure, so there is no change in behavior.
Fixes: c80ae7ca3726 ("crypto: arm/sha512 - accelerated SHA-512 using ARM generic ASM and NEON") Fixes: b59e2ae3690c ("crypto: arm/sha256 - move SHA-224/256 ASM/NEON implementation to base layer") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Reviewed-by: Ard Biesheuvel <ardb@kernel.org> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
of_parse_phandle() returns a device_node with refcount incremented, which
the callee needs to call of_node_put() on when done. We should only call
of_node_put() when the property argument is provided though as otherwise
nothing has taken a reference on the node.
Fixes: f36e789a1f8d ("mfd: altera-sysmgr: Add SOCFPGA System Manager") Signed-off-by: Peter Griffin <peter.griffin@linaro.org> Link: https://lore.kernel.org/r/20240220115012.471689-4-peter.griffin@linaro.org Signed-off-by: Lee Jones <lee@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
of_parse_phandle() returns a device_node with refcount incremented, which
the callee needs to call of_node_put() on when done. We should only call
of_node_put() when the property argument is provided though as otherwise
nothing has taken a reference on the node.
Fixes: 45330bb43421 ("mfd: syscon: Allow property as NULL in syscon_regmap_lookup_by_phandle") Signed-off-by: Peter Griffin <peter.griffin@linaro.org> Link: https://lore.kernel.org/r/20240220115012.471689-2-peter.griffin@linaro.org Signed-off-by: Lee Jones <lee@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Inside tegra_fb_create(), drm_gem_object_lookup() increments ref count of
the found object. But if the following size check fails then the last
found object's ref count should be put there as the unreferencing loop
can't detect this situation.
Found by Linux Verification Center (linuxtesting.org).
Per PCIe r6.1, sec 2.2.6.2 and 7.5.3.4, a Requester may not use 8-bit Tags
unless its Extended Tag Field Enable is set, but all Receivers/Completers
must handle 8-bit Tags correctly regardless of their Extended Tag Field
Enable.
Some devices do not handle 8-bit Tags as Completers, so add a quirk for
them. If we find such a device, we disable Extended Tags for the entire
hierarchy to make peer-to-peer DMA possible.
The 3ware 9650SE seems to have issues with handling 8-bit tags. Mark it as
broken.
The register bits definitions for RGB666 formats are wrong in multiple
ways: first, in the DSI_PS_SEL bits region, the Packed 18-bits RGB666
format is selected with bit 1, while the Loosely Packed one is bit 2,
and second - the definition name "LOOSELY_PS_18BIT_RGB666" is wrong
because the loosely packed format is 24 bits instead!
Either way, functions mtk_dsi_ps_control_vact() and mtk_dsi_ps_control()
do not even agree on the DSI_PS_SEL bit to set in DSI_PSCTRL: one sets
loosely packed (24) on RGB666, the other sets packed (18), and the other
way around for RGB666_PACKED.
Fixing this entire stack of issues is done in one go:
- Use the correct bit for the Loosely Packed RGB666 definition
- Rename LOOSELY_PS_18BIT_RGB666 to LOOSELY_PS_24BIT_RGB666
- Change ps_bpp_mode in mtk_dsi_ps_control_vact() to set:
- Loosely Packed, 24-bits for MIPI_DSI_FMT_RGB666
- Packed, 18-bits for MIPI_DSI_FMT_RGB666_PACKED
Currently coefficients are applied only once, since they don't change.
However, this is done before enable bit is set and thus it doesn't get
applied properly.
Fix that by applying coefficients after enable bit is set. While this
means that it will be done evey time, it doesn't bring much time
penalty.
clang-16 warns about casting functions to incompatible types, as is done
here to call clk_disable_unprepare:
sound/soc/meson/t9015.c:274:4: error: cast from 'void (*)(struct clk *)' to 'void (*)(void *)' converts to incompatible function type [-Werror,-Wcast-function-type-strict]
274 | (void(*)(void *))clk_disable_unprepare,
The pattern of getting, enabling and setting a disable callback for a
clock can be replaced with devm_clk_get_enabled(), which also fixes
this warning.
clang-16 warns about casting functions to incompatible types, as is done
here to call clk_disable_unprepare:
sound/soc/meson/aiu.c:243:12: error: cast from 'void (*)(struct clk *)' to 'void (*)(void *)' converts to incompatible function type [-Werror,-Wcast-function-type-strict]
243 | (void(*)(void *))clk_disable_unprepare,
The pattern of getting, enabling and setting a disable callback for a
clock can be replaced with devm_clk_get_enabled(), which also fixes
this warning.
Cycles is recognized as part of a hard coded metric in stat-shadow.c,
it may call print_metric_only with a NULL fmt string leading to a
segfault. Handle the NULL fmt explicitly.
Fixes: 088519f318be ("perf stat: Move the display functions to stat-display.c") Signed-off-by: Ian Rogers <irogers@google.com> Reviewed-by: Kan Liang <kan.liang@linux.intel.com> Cc: K Prateek Nayak <kprateek.nayak@amd.com> Cc: James Clark <james.clark@arm.com> Cc: Kaige Ye <ye@kaige.org> Cc: John Garry <john.g.garry@oracle.com> Signed-off-by: Namhyung Kim <namhyung@kernel.org> Link: https://lore.kernel.org/r/20240209204947.3873294-4-irogers@google.com Signed-off-by: Sasha Levin <sashal@kernel.org>
The commit in Fixes changed the logic on how resources are released and
introduced a new switchtec_exit_pci() that need to be called explicitly in
order to undo a corresponding switchtec_init_pci().
This was done in the remove function, but not in the probe.
Dquot pointers in i_dquot array in the inode are protected by
dquot_srcu. Annotate the array pointers with __rcu, perform the locked
dereferences with srcu_dereference_check() instead of plain reads, and
set the array elements with rcu_assign_pointer().
Fixes: b9ba6f94b238 ("quota: remove dqptr_sem") Reported-by: kernel test robot <lkp@intel.com> Closes: https://lore.kernel.org/oe-kbuild-all/202402061900.rTuYDlo6-lkp@intel.com/ Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Sasha Levin <sashal@kernel.org>
If dquot_free_inode(or other routines) checks inode's quota pointers (1)
before quota_off sets it to NULL(2) and use it (3) after that, NULL pointer
dereference will be triggered.
So let's fix it by using a temporary pointer to avoid this issue.
Signed-off-by: Wang Jianjian <wangjianjian3@huawei.com> Signed-off-by: Jan Kara <jack@suse.cz>
Message-Id: <20240202081852.2514092-1-wangjianjian3@huawei.com>
Stable-dep-of: 179b8c97ebf6 ("quota: Fix rcu annotations of inode dquot pointers") Signed-off-by: Sasha Levin <sashal@kernel.org>
As Honza said, remove_inode_dquot_ref() currently does not release the
last dquot reference but instead adds the dquot to tofree_head list. This
is because dqput() can sleep while dropping of the last dquot reference
(writing back the dquot and calling ->release_dquot()) and that must not
happen under dq_list_lock. Now that dqput() queues the final dquot cleanup
into a workqueue, remove_inode_dquot_ref() can call dqput() unconditionally
and we can significantly simplify it.
Here we open code the simplified code of remove_inode_dquot_ref() into
remove_dquot_ref() and remove the function put_dquot_list() which is no
longer used.
Signed-off-by: Baokun Li <libaokun1@huawei.com> Signed-off-by: Jan Kara <jack@suse.cz>
Message-Id: <20230630110822.3881712-6-libaokun1@huawei.com>
Stable-dep-of: 179b8c97ebf6 ("quota: Fix rcu annotations of inode dquot pointers") Signed-off-by: Sasha Levin <sashal@kernel.org>
Trying to toggle the resets in a rapid fashion can lead to the changes
not actually arriving at the clock controller block when we expect them
to. This was observed at least on SM8250.
Read back the value after regmap_update_bits to ensure write completion.
The MT8192 does not support configuring pin slew rate. This is evident
from both the datasheet, and the fact that the driver points the slew
rate register range at the GPIO direction register range.
Drop the bogus setting.
Fixes: d32f38f2a8fc ("pinctrl: mediatek: Add pinctrl driver for mt8192") Signed-off-by: Chen-Yu Tsai <wenst@chromium.org> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Link: https://lore.kernel.org/r/20240131071910.3950450-2-wenst@chromium.org Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In dvb_register_device, *pdvbdev is set equal to dvbdev, which is freed
in several error-handling paths. However, *pdvbdev is not set to NULL
after dvbdev's deallocation, causing use-after-frees in many places,
for example, in the following call chain:
When calling dvb_unregister_device, dmxdev->dvbdev (i.e. *pdvbdev in
dvb_register_device) could point to memory that had been freed in
dvb_register_device. Thereafter, this pointer is transferred to
kref_put and triggering a use-after-free.
The entity->name (i.e. name) is allocated in v4l2_m2m_register_entity
but isn't freed in its following error-handling paths. This patch
adds such deallocation to prevent memleak of entity->name.
Fixes: be2fff656322 ("media: add helpers for memory-to-memory media controller") Signed-off-by: Zhipeng Lu <alexious@zju.edu.cn> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Sasha Levin <sashal@kernel.org>
In tpg_alloc, resources should be deallocated in each and every
error-handling paths, since they are allocated in for statements.
Otherwise there would be memleaks because tpg_free is called only when
tpg_alloc return 0.
Fixes: 63881df94d3e ("[media] vivid: add the Test Pattern Generator") Signed-off-by: Zhipeng Lu <alexious@zju.edu.cn> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Sasha Levin <sashal@kernel.org>
Static analyzers generate alerts for an unchecked call to
`media_device_register()`. However, in this case, the device will work
reliably without the media controller API.
Add a comment above the call to prevent future unnecessary changes.
The 'stream' pointer is used in dcn10_set_output_transfer_func() before
the check if 'stream' is NULL.
Fixes the below:
drivers/gpu/drm/amd/amdgpu/../display/dc/hwss/dcn10/dcn10_hwseq.c:1892 dcn10_set_output_transfer_func() warn: variable dereferenced before check 'stream' (see line 1875)
Fixes: ddef02de0d71 ("drm/amd/display: add null checks before logging") Cc: Wyatt Wood <wyatt.wood@amd.com> Cc: Anthony Koo <Anthony.Koo@amd.com> Cc: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com> Cc: Aurabindo Pillai <aurabindo.pillai@amd.com> Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com> Reviewed-by: Anthony Koo <Anthony.Koo@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Tell snprintf() to store at most 10 bytes in the output buffer
instead of 30.
Fixes the below:
drivers/gpu/drm/amd/amdgpu/../display/amdgpu_dm/amdgpu_dm_debugfs.c:1508 dp_dsc_clock_en_read() error: snprintf() is printing too much 30 vs 10
Fixes: c06e09b76639 ("drm/amd/display: Add DSC parameters logging to debugfs") Cc: Alex Hung <alex.hung@amd.com> Cc: Qingqing Zhuo <qingqing.zhuo@amd.com> Cc: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com> Cc: Aurabindo Pillai <aurabindo.pillai@amd.com> Cc: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com> Reviewed-by: Harry Wentland <harry.wentland@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Previous attempt to autodetect well-behaving patched firmware
introduced in commit 46a0a2c96f0f ("HID: lenovo: Detect quirk-free fw
on cptkbd and stop applying workaround") has shown that there are
false-positives on original firmware (on both 1st gen and 2nd gen
keyboards) which causes the middle button click workaround to be
mistakenly disabled.
This commit adds explicit parameter to sysfs to control this
workaround.
Fixes: 46a0a2c96f0f ("HID: lenovo: Detect quirk-free fw on cptkbd and stop applying workaround") Fixes: 43527a0094c1 ("HID: lenovo: Restrict detection of patched firmware only to USB cptkbd") Signed-off-by: Mikhail Khvainitski <me@khvoinitsky.org> Signed-off-by: Jiri Kosina <jkosina@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
perf_data__switch() may not assign a legal value to 'new_filename'.
In this case, 'new_filename' uses the on-stack value, which may cause a
incorrect free and unexpected result.
Fixes: 03724b2e9c45 ("perf record: Allow to limit number of reported perf.data files") Signed-off-by: Yang Jihong <yangjihong1@huawei.com> Acked-by: Namhyung Kim <namhyung@kernel.org> Link: https://lore.kernel.org/r/20240119040304.3708522-2-yangjihong1@huawei.com Signed-off-by: Namhyung Kim <namhyung@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The TLP Prefix Log Register consists of multiple DWORDs (PCIe r6.1 sec
7.9.14.13) but the loop in dpc_process_rp_pio_error() keeps reading from
the first DWORD, so we print only the first PIO TLP Prefix (duplicated
several times), and we never print the second, third, etc., Prefixes.
Add the iteration count based offset calculation into the config read.
Update the architecture dependency to be the generic Tegra
because the driver works on the four latest Tegra generations
not just T210, if you build a kernel with a specific
ARCH_TEGRA_xxx_SOC option that excludes 210 you don't get
this driver.
Fixes: 433de642a76c9 ("dmaengine: tegra210-adma: add support for Tegra186/Tegra194") Signed-off-by: Peter Robinson <pbrobinson@gmail.com> Cc: Jon Hunter <jonathanh@nvidia.com> Cc: Thierry Reding <treding@nvidia.com> Cc: Sameer Pujar <spujar@nvidia.com> Cc: Laxman Dewangan <ldewangan@nvidia.com> Reviewed-by: Jon Hunter <jonathanh@nvidia.com> Link: https://lore.kernel.org/r/20240112093310.329642-2-pbrobinson@gmail.com Signed-off-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
This scary message can misled the user into thinking something bad has
happened and needs to be fixed, however it could simply be part of a
normal boot process where EPROBE_DEFER is taken into account. Therefore,
let's use dev_err_probe so that this message doesn't get shown (by
default) when the return code is EPROBE_DEFER.
ret variable stores the return value of drm_of_find_panel_or_bridge
which can return error codes different from EPROBE_DEFER. Therefore,
let's just return that error code instead of forcing it to EPROBE_DEFER.
Unit testing this in VKMS shows that passing 0 into
this function returns -1, which is highly counter-
intuitive. Fix it by checking whether the input is
>= 0 instead of > 0.
Fixes: 64566b5e767f ("drm: Add drm_fixp_from_fraction and drm_fixp2int_ceil") Signed-off-by: Harry Wentland <harry.wentland@amd.com> Reviewed-by: Simon Ser <contact@emersion.fr> Reviewed-by: Melissa Wen <mwen@igalia.com> Signed-off-by: Melissa Wen <melissa.srw@gmail.com> Link: https://patchwork.freedesktop.org/patch/msgid/20231108163647.106853-2-harry.wentland@amd.com Signed-off-by: Sasha Levin <sashal@kernel.org>
The controller wants the difference between *total and *sync_start in the
HDMI_VIDEO_EXT_*DELAY registers. Otherwise the signal is very unstable for
certain non-VIC modes. See downstream commit [0].
When possible use dev_err_probe help to properly deal with the
PROBE_DEFER error, the benefit is that DEFER issue will be logged
in the devices_deferred debugfs file.
And using dev_err_probe() can reduce code size, the error value
gets printed.
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
Stable-dep-of: 830c1ded3563 ("drm/tegra: dsi: Fix some error handling paths in tegra_dsi_probe()") Signed-off-by: Sasha Levin <sashal@kernel.org>
There is this reported crash when experimenting with the lvm2 testsuite.
The list corruption is caused by the fact that the postsuspend and resume
methods were not paired correctly; there were two consecutive calls to the
origin_postsuspend function. The second call attempts to remove the
"hash_list" entry from a list, while it was already removed by the first
call.
Fix __dm_internal_resume so that it calls the preresume and resume
methods of the table's targets.
If a preresume method of some target fails, we are in a tricky situation.
We can't return an error because dm_internal_resume isn't supposed to
return errors. We can't return success, because then the "resume" and
"postsuspend" methods would not be paired correctly. So, we set the
DMF_SUSPENDED flag and we fake normal suspend - it may confuse userspace
tools, but it won't cause a kernel crash.
An empty flush doesn't have a payload, so it should never be looked at
when considering to possibly requeue a bio for the case when a reshape
is in progress.
Fixes: 9dbd1aa3a81c ("dm raid: add reshaping support to the target") Reported-by: Patrick Plenefisch <simonpatp@gmail.com> Signed-off-by: Ming Lei <ming.lei@redhat.com> Signed-off-by: Mike Snitzer <snitzer@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The kmalloc_array() in nfp_fl_lag_do_work() will return null, if
the physical memory has run out. As a result, if we dereference
the acti_netdevs, the null pointer dereference bugs will happen.
This patch adds a check to judge whether allocation failure occurs.
If it happens, the delayed work will be rescheduled and try again.
Fixes: bb9a8d031140 ("nfp: flower: monitor and offload LAG groups") Signed-off-by: Duoming Zhou <duoming@zju.edu.cn> Reviewed-by: Louis Peens <louis.peens@corigine.com> Link: https://lore.kernel.org/r/20240308142540.9674-1-duoming@zju.edu.cn Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The 'len' variable can't be negative when assigned the result of
'min_t' because all 'min_t' parameters are cast to unsigned int,
and then the minimum one is chosen.
To fix the logic, check 'len' as read from 'optlen',
where the types of relevant variables are (signed) int.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Gavrilov Ilia <Ilia.Gavrilov@infotecs.ru> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The 'len' variable can't be negative when assigned the result of
'min_t' because all 'min_t' parameters are cast to unsigned int,
and then the minimum one is chosen.
To fix the logic, check 'len' as read from 'optlen',
where the types of relevant variables are (signed) int.
Fixes: ab7ac4eb9832 ("kcm: Kernel Connection Multiplexor module") Signed-off-by: Gavrilov Ilia <Ilia.Gavrilov@infotecs.ru> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The 'len' variable can't be negative when assigned the result of
'min_t' because all 'min_t' parameters are cast to unsigned int,
and then the minimum one is chosen.
To fix the logic, check 'len' as read from 'optlen',
where the types of relevant variables are (signed) int.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Reviewed-by: Willem de Bruijn <willemb@google.com> Signed-off-by: Gavrilov Ilia <Ilia.Gavrilov@infotecs.ru> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The 'len' variable can't be negative when assigned the result of
'min_t' because all 'min_t' parameters are cast to unsigned int,
and then the minimum one is chosen.
To fix the logic, check 'len' as read from 'optlen',
where the types of relevant variables are (signed) int.
Fixes: 3557baabf280 ("[L2TP]: PPP over L2TP driver core") Reviewed-by: Tom Parkin <tparkin@katalix.com> Signed-off-by: Gavrilov Ilia <Ilia.Gavrilov@infotecs.ru> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The 'olr' variable can't be negative when assigned the result of
'min_t' because all 'min_t' parameters are cast to unsigned int,
and then the minimum one is chosen.
To fix the logic, check 'olr' as read from 'optlen',
where the types of relevant variables are (signed) int.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Gavrilov Ilia <Ilia.Gavrilov@infotecs.ru> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Similar to the earlier patch that changes sk_getsockopt() to
take the sockptr_t argument. This patch also changes
do_ip_getsockopt() to take the sockptr_t argument such that
a latter patch can make bpf_getsockopt(SOL_IP) to reuse
do_ip_getsockopt().
Note on the change in ip_mc_gsfget(). This function is to
return an array of sockaddr_storage in optval. This function
is shared between ip_get_mcast_msfilter() and
compat_ip_get_mcast_msfilter(). However, the sockaddr_storage
is stored at different offset of the optval because of
the difference between group_filter and compat_group_filter.
Thus, a new 'ss_offset' argument is added to ip_mc_gsfget().
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org> Link: https://lore.kernel.org/r/20220902002828.2890585-1-kafai@fb.com Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Stable-dep-of: 5c3be3e0eb44 ("ipmr: fix incorrect parameter validation in the ip_mroute_getsockopt() function") Signed-off-by: Sasha Levin <sashal@kernel.org>
There is a regular need in the kernel to provide a way to declare having
a dynamically sized set of trailing elements in a structure. Kernel code
should always use “flexible array members”[1] for these cases. The older
style of one-element or zero-length arrays should no longer be used[2].
Use an anonymous union with a couple of anonymous structs in order to
keep userspace unchanged and refactor the related code accordingly:
This helps with the ongoing efforts to globally enable -Warray-bounds
and get us closer to being able to tighten the FORTIFY_SOURCE routines
on memcpy().
Revert the use of structr_size() and stay with IP_MSFILTER_SIZE() for
now, as in this case, the size of struct ip_msfilter didn't change with
the addition of the flexible array imsf_slist_flex[]. So, if we use
struct_size() we will be allocating and calculating the size of
struct ip_msfilter with one too many items for imsf_slist_flex[].
We might use struct_size() in the future, but for now let's stay
with IP_MSFILTER_SIZE().
Fixes: 2d3e5caf96b9 ("net/ipv4: Replace one-element array with flexible-array member") Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: 5c3be3e0eb44 ("ipmr: fix incorrect parameter validation in the ip_mroute_getsockopt() function") Signed-off-by: Sasha Levin <sashal@kernel.org>
There is a regular need in the kernel to provide a way to declare having
a dynamically sized set of trailing elements in a structure. Kernel code
should always use “flexible array members”[1] for these cases. The older
style of one-element or zero-length arrays should no longer be used[2].
Use an anonymous union with a couple of anonymous structs in order to
keep userspace unchanged:
Also, refactor the code accordingly and make use of the struct_size()
and flex_array_size() helpers.
This helps with the ongoing efforts to globally enable -Warray-bounds
and get us closer to being able to tighten the FORTIFY_SOURCE routines
on memcpy().
The 'len' variable can't be negative when assigned the result of
'min_t' because all 'min_t' parameters are cast to unsigned int,
and then the minimum one is chosen.
To fix the logic, check 'len' as read from 'optlen',
where the types of relevant variables are (signed) int.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Gavrilov Ilia <Ilia.Gavrilov@infotecs.ru> Reviewed-by: Jason Xing <kerneljasonxing@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
If the kernel isn't built with interconnect support, icc_get_name()
returns NULL and we get following warning:
drivers/opp/debugfs.c: In function 'bw_name_read':
drivers/opp/debugfs.c:43:42: error: '%.62s' directive argument is null [-Werror=format-overflow=]
i = scnprintf(buf, sizeof(buf), "%.62s\n", icc_get_name(path));
Fix it.
Reported-by: kernel test robot <lkp@intel.com> Closes: https://lore.kernel.org/oe-kbuild-all/202402141313.81ltVF5g-lkp@intel.com/ Fixes: 0430b1d5704b0 ("opp: Expose bandwidth information via debugfs") Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org> Reviewed-by: Dhruva Gole <d-gole@ti.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The logic for enabling the TX clock shift is inverse of enabling the RX
clock shift. The TX clock shift is disabled when DP83822_TX_CLK_SHIFT is
set. Correct the current behavior and always write the delay configuration
to ensure consistent delay settings regardless of bootloader configuration.
Reference: https://www.ti.com/lit/ds/symlink/dp83822i.pdf p. 69
Fixes: 8095295292b5 ("net: phy: DP83822: Add setting the fixed internal delay") Signed-off-by: Tim Pambor <tp@osasysteme.de> Link: https://lore.kernel.org/r/20240305110608.104072-1-tp@osasysteme.de Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
RGMII mode can be enable from dp83822 straps, and also writing bit 9
of register 0x17 - RMII and Status Register (RCSR).
When phy_interface_is_rgmii rgmii mode must be enabled, same for
contrary, this prevents malconfigurations of hw straps
Currently, the mac port is fixed to configured as full dplex mode in
hclge_mac_init() when driver initialization or reset restore. Users may
change the mode to half duplex with ethtool, so it may cause the user
configuration dropped after reset.
To fix it, don't change the duplex mode when resetting.
Fixes: 2d03eacc0b7e ("net: hns3: Only update mac configuation when necessary") Signed-off-by: Jie Wang <wangjie125@huawei.com> Signed-off-by: Jijie Shao <shaojijie@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The phy_get_internal_delay function could try to access to an empty
array in the case that the driver is calling phy_get_internal_delay
without defining delay_values and rx-internal-delay-ps or
tx-internal-delay-ps is defined to 0 in the device-tree.
This will lead to "unable to handle kernel NULL pointer dereference at
virtual address 0". To avoid this kernel oops, the test should be delay
>= 0. As there is already delay < 0 test just before, the test could
only be size == 0.
Fixes: 92252eec913b ("net: phy: Add a helper to return the index for of the internal delay") Co-developed-by: Enguerrand de Ribaucourt <enguerrand.de-ribaucourt@savoirfairelinux.com> Signed-off-by: Enguerrand de Ribaucourt <enguerrand.de-ribaucourt@savoirfairelinux.com> Signed-off-by: Kévin L'hôpital <kevin.lhopital@savoirfairelinux.com> Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
8d975c15c0cd ("ip6_tunnel: make sure to pull inner header in __ip6_tnl_rcv()") 1ca1ba465e55 ("geneve: make sure to pull inner header in geneve_rx()")
We have to save skb->network_header in a temporary variable
in order to be able to recompute the network_header pointer
after a pskb_inet_may_pull() call.
pskb_inet_may_pull() makes sure the needed headers are in skb->head.
Fixes: c54419321455 ("GRE: Refactor GRE tunneling code.") Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
When rule policy is changed, ipv6 socket cache is not refreshed.
The sock's skb still uses a outdated route cache and was sent to
a wrong interface.
To avoid this error we should update fib node's version when
rule is changed. Then skb's route will be reroute checked as
route cache version is already different with fib node version.
The route cache is refreshed to match the latest rule.
Fixes: 101367c2f8c4 ("[IPV6]: Policy Routing Rules") Signed-off-by: Shiming Cheng <shiming.cheng@mediatek.com> Signed-off-by: Lena Wang <lena.wang@mediatek.com> Reviewed-by: David Ahern <dsahern@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The stackmap code relies on roundup_pow_of_two() to compute the number
of hash buckets, and contains an overflow check by checking if the
resulting value is 0. However, on 32-bit arches, the roundup code itself
can overflow by doing a 32-bit left-shift of an unsigned long value,
which is undefined behaviour, so it is not guaranteed to truncate
neatly. This was triggered by syzbot on the DEVMAP_HASH type, which
contains the same check, copied from the hashtab code.
The commit in the fixes tag actually attempted to fix this, but the fix
did not account for the UB, so the fix only works on CPUs where an
overflow does result in a neat truncation to zero, which is not
guaranteed. Checking the value before rounding does not have this
problem.
Fixes: 6183f4d3a0a2 ("bpf: Check for integer overflow when using roundup_pow_of_two()") Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com> Reviewed-by: Bui Quang Minh <minhquangbui99@gmail.com>
Message-ID: <20240307120340.99577-4-toke@redhat.com> Signed-off-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The hashtab code relies on roundup_pow_of_two() to compute the number of
hash buckets, and contains an overflow check by checking if the
resulting value is 0. However, on 32-bit arches, the roundup code itself
can overflow by doing a 32-bit left-shift of an unsigned long value,
which is undefined behaviour, so it is not guaranteed to truncate
neatly. This was triggered by syzbot on the DEVMAP_HASH type, which
contains the same check, copied from the hashtab code. So apply the same
fix to hashtab, by moving the overflow check to before the roundup.
Fixes: daaf427c6ab3 ("bpf: fix arraymap NULL deref and missing overflow and zero size checks") Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Message-ID: <20240307120340.99577-3-toke@redhat.com> Signed-off-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The devmap code allocates a number hash buckets equal to the next power
of two of the max_entries value provided when creating the map. When
rounding up to the next power of two, the 32-bit variable storing the
number of buckets can overflow, and the code checks for overflow by
checking if the truncated 32-bit value is equal to 0. However, on 32-bit
arches the rounding up itself can overflow mid-way through, because it
ends up doing a left-shift of 32 bits on an unsigned long value. If the
size of an unsigned long is four bytes, this is undefined behaviour, so
there is no guarantee that we'll end up with a nice and tidy 0-value at
the end.
Syzbot managed to turn this into a crash on arm32 by creating a
DEVMAP_HASH with max_entries > 0x80000000 and then trying to update it.
Fix this by moving the overflow check to before the rounding up
operation.
Fixes: 6f9d451ab1a3 ("xdp: Add devmap_hash map type for looking up devices by hashed index") Link: https://lore.kernel.org/r/000000000000ed666a0611af6818@google.com Reported-and-tested-by: syzbot+8cd36f6b65f3cafd400a@syzkaller.appspotmail.com Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Message-ID: <20240307120340.99577-2-toke@redhat.com> Signed-off-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
struct hci_dev_info has a fixed size name[8] field so in the event that
hdev->name is bigger than that strcpy would attempt to write past its
size, so this fixes this problem by switching to use strscpy.
Fixes: dcda165706b9 ("Bluetooth: hci_core: Fix build warnings") Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The "pending connections" feature was originally introduced with commit 4c67bc74f016 ("[Bluetooth] Support concurrent connect requests") and 6bd57416127e ("[Bluetooth] Handling pending connect attempts after
inquiry") to handle controllers supporting only a single connection request
at a time. Later things were extended to also cancel ongoing inquiries on
connect() with commit 89e65975fea5 ("Bluetooth: Cancel Inquiry before
Create Connection").
With commit a9de9248064b ("[Bluetooth] Switch from OGF+OCF to using only
opcodes"), hci_conn_check_pending() was introduced as a helper to
consolidate a few places where we check for pending connections (indicated
by the BT_CONNECT2 flag) and then try to connect.
This refactoring commit also snuck in two more calls to
hci_conn_check_pending():
- One is in the failure callback of hci_cs_inquiry(), this one probably
makes sense: If we send an "HCI Inquiry" command and then immediately
after a "Create Connection" command, the "Create Connection" command might
fail before the "HCI Inquiry" command, and then we want to retry the
"Create Connection" on failure of the "HCI Inquiry".
- The other added call to hci_conn_check_pending() is in the event handler
for the "Remote Name" event, this seems unrelated and is possibly a
copy-paste error, so remove that one.
Fixes: a9de9248064b ("[Bluetooth] Switch from OGF+OCF to using only opcodes") Signed-off-by: Jonas Dreßler <verdre@v0yd.nl> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fix "double" clearing of interrupts, which can cause external events
or timestamps to be missed.
The E1000_TSIRC Time Sync Interrupt Cause register can be cleared in two
ways, by either reading it or by writing '1' into the specific cause
bit. This is documented in section 8.16.1.
The following flow was used:
1. read E1000_TSIRC into 'tsicr';
2. handle the interrupts present into 'tsirc' and mark them in 'ack';
3. write 'ack' into E1000_TSICR;
As both (1) and (3) will clear the interrupt cause, if the same
interrupt happens again between (1) and (3) it will be ignored,
causing events to be missed.
Remove the extra clear in (3).
Fixes: 00c65578b47b ("igb: enable internal PPS for the i210") Acked-by: Richard Cochran <richardcochran@gmail.com> Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com> Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Remove code duplication in the tsync interrupt handler function by moving
this logic to separate functions. This keeps the interrupt handler readable
and allows the new functions to be extended for adapter types other than
i210.
Signed-off-by: Ruud Bos <kernel.hbk@gmail.com> Tested-by: Gurucharan G <gurucharanx.g@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Stable-dep-of: ee14cc9ea19b ("igb: Fix missing time sync events") Signed-off-by: Sasha Levin <sashal@kernel.org>
For those endpoint devices connect to system via hotplug capable ports,
users could request a hot reset to the device by flapping device's link
through setting the slot's link control register, as pciehp_ist() DLLSC
interrupt sequence response, pciehp will unload the device driver and
then power it off. thus cause an IOMMU device-TLB invalidation (Intel
VT-d spec, or ATS Invalidation in PCIe spec r6.1) request for non-existence
target device to be sent and deadly loop to retry that request after ITE
fault triggered in interrupt context.
That would cause following continuous hard lockup warning and system hang
Such issue could be triggered by all kinds of regular surprise removal
hotplug operation. like:
1. pull EP(endpoint device) out directly.
2. turn off EP's power.
3. bring the link down.
etc.
this patch aims to work for regular safe removal and surprise removal
unplug. these hot unplug handling process could be optimized for fix the
ATS Invalidation hang issue by calling pci_dev_is_disconnected() in
function devtlb_invalidation_with_pasid() to check target device state to
avoid sending meaningless ATS Invalidation request to iommu when device is
gone. (see IMPLEMENTATION NOTE in PCIe spec r6.1 section 10.3.1)
For safe removal, device wouldn't be removed until the whole software
handling process is done, it wouldn't trigger the hard lock up issue
caused by too long ATS Invalidation timeout wait. In safe removal path,
device state isn't set to pci_channel_io_perm_failure in
pciehp_unconfigure_device() by checking 'presence' parameter, calling
pci_dev_is_disconnected() in devtlb_invalidation_with_pasid() will return
false there, wouldn't break the function.
For surprise removal, device state is set to pci_channel_io_perm_failure in
pciehp_unconfigure_device(), means device is already gone (disconnected)
call pci_dev_is_disconnected() in devtlb_invalidation_with_pasid() will
return true to break the function not to send ATS Invalidation request to
the disconnected device blindly, thus avoid to trigger further ITE fault,
and ITE fault will block all invalidation request to be handled.
furthermore retry the timeout request could trigger hard lockup.
Make pci_dev_is_disconnected() public so that it can be called from
Intel VT-d driver to quickly fix/workaround the surprise removal
unplug hang issue for those ATS capable devices on PCIe switch downstream
hotplug capable ports.
Beside pci_device_is_present() function, this one has no config space
space access, so is light enough to optimize the normal pure surprise
removal and safe removal flow.
Acked-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Dan Carpenter <dan.carpenter@linaro.org> Tested-by: Haorong Ye <yehaorong@bytedance.com> Signed-off-by: Ethan Zhao <haifeng.zhao@linux.intel.com> Link: https://lore.kernel.org/r/20240301080727.3529832-2-haifeng.zhao@linux.intel.com Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com> Signed-off-by: Joerg Roedel <jroedel@suse.de>
Stable-dep-of: 4fc82cd907ac ("iommu/vt-d: Don't issue ATS Invalidation request when device is disconnected") Signed-off-by: Sasha Levin <sashal@kernel.org>
The creds and oa->data need to be freed in the error-handling paths after
their allocation. So this patch add these deallocations in the
corresponding paths.
Fixes: 1d658336b05f ("SUNRPC: Add RPC based upcall mechanism for RPCGSS auth") Signed-off-by: Zhipeng Lu <alexious@zju.edu.cn> Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / thirdparty / kernel / stable.git / log
