The dummy-hcd UDC driver is not careful about the way it handles
connection speeds. It ignores the module parameter that is supposed
to govern the maximum connection speed and it doesn't set the HCD
flags properly for the case where it ends up running at full speed.
The result is that in many cases, gadget enumeration over dummy-hcd
fails because the bMaxPacketSize byte in the device descriptor is set
incorrectly. For example, the default settings call for a high-speed
connection, but the maxpacket value for ep0 ends up being set for a
Super-Speed connection.
This patch fixes the problem by initializing the gadget's max_speed
and the HCD flags correctly.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Servers were emitting failed handoff messages but were not
waiting the full 1 second as designated in section 4.22.1 of
the eXtensible Host Controller Interface specifications. The
handshake was using wrong units so calls were made with milliseconds
not microseconds. Comments referenced 5 seconds not 1 second as
in specs.
The wrong units were also corrected in a second handshake call.
When a USB-audio device receives a maliciously adjusted or corrupted
buffer descriptor, the USB-audio driver may access an out-of-bounce
value at its parser. This was detected by syzkaller, something like:
This patch fixes an issue that the usbhsf_fifo_clear() is possible
to cause 10 msec delay if the pipe is RX direction and empty because
the FRDY bit will never be set to 1 in such case.
Fixes: e8d548d54968 ("usb: renesas_usbhs: fifo became independent from pipe.") Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes an issue that the driver sets the BCLR bit of
{C,Dn}FIFOCTR register to 1 even when it's non-DCP pipe and
the FRDY bit of {C,Dn}FIFOCTR register is set to 1.
Fixes: e8d548d54968 ("usb: renesas_usbhs: fifo became independent from pipe.") Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Kris Lindgren reports that without the NO_WP_DETECT flag, his Seagate
external disk drive fails all write accesses. This regresssion dates
back approximately to the start of the 4.x kernel releases.
The driver triggers actions on both edges of the vbus signal.
The former PIO controller was triggering IRQs on both falling and rising edges
by default. Newer PIO controller don't, so it's better to set it explicitly to
IRQF_TRIGGER_FALLING | IRQF_TRIGGER_RISING.
Without this patch we may trigger the connection with host but only on some
bouncing signal conditions and thus lose connecting events.
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The gadgetfs driver as a long-outstanding FIXME, regarding a call of
copy_to_user() made while holding a spinlock. This patch fixes the
issue by dropping the spinlock and using the dev->udc_usage mechanism
introduced by another recent patch to guard against status changes
while the lock isn't held.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Reported-by: Andrey Konovalov <andreyknvl@google.com> Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The gadgetfs driver (drivers/usb/gadget/legacy/inode.c) was written
before the UDC and composite frameworks were adopted; it is a legacy
driver. As such, it expects that once bound to a UDC controller, it
will not be unbound until it unregisters itself.
However, the UDC framework does unbind function drivers while they are
still registered. When this happens, it can cause the gadgetfs driver
to misbehave or crash. For example, userspace can cause a crash by
opening the device file and doing an ioctl call before setting up a
configuration (found by Andrey Konovalov using the syzkaller fuzzer).
This patch adds checks and synchronization to prevent these bad
behaviors. It adds a udc_usage counter that the driver increments at
times when it is using a gadget interface without holding the private
spinlock. The unbind routine waits for this counter to go to 0 before
returning, thereby ensuring that the UDC is no longer in use.
The patch also adds a check in the dev_ioctl() routine to make sure
the driver is bound to a UDC before dereferencing the gadget pointer,
and it makes destroy_ep_files() synchronize with the endpoint I/O
routines, to prevent the user from accessing an endpoint data
structure after it has been removed.
Fix bad unlock balance: ep0_write enter with the locks locked from
inode.c:1769, hence it must exit with spinlock held to avoid double
unlock in dev_config.
Signed-off-by: David Eccher <d.eccher@gmail.com> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In file included from drivers/media/pci/ttpci/av7110.c:63:0:
In function 'irdebi.isra.2',
inlined from 'start_debi_dma' at drivers/media/pci/ttpci/av7110.c:376:3,
inlined from 'gpioirq' at drivers/media/pci/ttpci/av7110.c:659:3:
drivers/media/pci/ttpci/av7110_hw.h:406:3: warning: 'memcpy': specified size between 18446744071562067968 and 18446744073709551615 exceeds maximum object size 9223372036854775807 [-Wstringop-overflow=]
memcpy(av7110->debi_virt, (char *) &res, count);
In function 'irdebi.isra.2',
inlined from 'start_debi_dma' at drivers/media/pci/ttpci/av7110.c:376:3,
inlined from 'gpioirq' at drivers/media/pci/ttpci/av7110.c:668:3:
drivers/media/pci/ttpci/av7110_hw.h:406:3: warning: 'memcpy': specified size between 18446744071562067968 and 18446744073709551615 exceeds maximum object size 9223372036854775807 [-Wstringop-overflow=]
memcpy(av7110->debi_virt, (char *) &res, count);
Apparently, 'count' can be negative here, which will then get turned
into a giant size argument for memcpy. Changing the sizes to 'unsigned
int' instead seems safe as we already check for maximum sizes, and it
also simplifies the code a bit.
The latest gcc-7.0.1 snapshot points out that we if nr_ch is zero, we never
initialize some variables:
sound/pci/au88x0/au88x0_core.c: In function 'vortex_adb_allocroute':
sound/pci/au88x0/au88x0_core.c:2304:68: error: 'mix[0]' may be used uninitialized in this function [-Werror=maybe-uninitialized]
sound/pci/au88x0/au88x0_core.c:2305:58: error: 'src[0]' may be used uninitialized in this function [-Werror=maybe-uninitialized]
I assume this can never happen in practice, but adding a check here doesn't
hurt either and avoids the warning. The code has been unchanged since
the start of git history.
aarch64-linux-gcc-7 complains about code it doesn't fully understand:
drivers/infiniband/hw/qib/qib_iba7322.c: In function 'qib_7322_txchk_change':
include/asm-generic/bitops/non-atomic.h:105:35: error: 'shadow' may be used uninitialized in this function [-Werror=maybe-uninitialized]
The code is right, and despite trying hard, I could not come up with a version
that I liked better than just adding a fake initialization here to shut up the
warning.
Fixes: f931551bafe1 ("IB/qib: Add new qib driver for QLogic PCIe InfiniBand adapters") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Ira Weiny <ira.weiny@intel.com> Signed-off-by: Doug Ledford <dledford@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Without this patch, failed probe would not free resources like irq.
ata port tdev object currently hold a reference to the ata port
object. Therefore the ata port object release function will not get
called until the ata_tport_release is called. But that would never
happen, releasing the last reference of ata port dev is done by
scsi_host_release, which is called by ata_host_release when the ata
port object is released.
The ata device objects actually do not need to explicitly hold a
reference to their real counterpart, given the transport objects are
the children of these objects and device_add() is call for each child.
We know the parent will not be deleted until we call the child's
device_del().
The sole remaining caller of kmem_zalloc_greedy is bulkstat, which uses
it to grab 1-4 pages for staging of inobt records. The infinite loop in
the greedy allocation function is causing hangs[1] in generic/269, so
just get rid of the greedy allocator in favor of kmem_zalloc_large.
This makes bulkstat somewhat more likely to ENOMEM if there's really no
pages to spare, but eliminates a source of hangs.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 57c67df(md/raid10: submit IO from originating thread instead of
md thread) submits bio directly for normal disks but not for replacement
disks. There is no point we shouldn't do this for replacement disks.
In the function rds_ib_setup_qp, the error handle is missing. When some
error occurs, it is possible that memory leak occurs. As such, error
handle is added.
Cc: Joe Jin <joe.jin@oracle.com> Reviewed-by: Junxiao Bi <junxiao.bi@oracle.com> Reviewed-by: Guanglei Li <guanglei.li@oracle.com> Signed-off-by: Zhu Yanjun <yanjun.zhu@oracle.com> Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Do a check for already installed leaf entry at the current level before
dereferencing it in order to avoid walking the page table down with
wrong pointer to the next level.
Signed-off-by: Oleksandr Tyshchenko <oleksandr_tyshchenko@epam.com> CC: Will Deacon <will.deacon@arm.com> CC: Robin Murphy <robin.murphy@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The helper->expect_class_max must be set to the total number of
expect_policy minus 1, since we will use the statement "if (class >
helper->expect_class_max)" to validate the CTA_EXPECT_CLASS attr in
ctnetlink_alloc_expect.
So for compatibility, set the helper->expect_class_max to the
NFCTH_POLICY_SET_NUM attr's value minus 1.
Also: it's invalid when the NFCTH_POLICY_SET_NUM attr's value is zero.
1. this will result "expect_policy = kzalloc(0, GFP_KERNEL);";
2. we cannot set the helper->expect_class_max to a proper value.
So if nla_get_be32(tb[NFCTH_POLICY_SET_NUM]) is zero, report -EINVAL to
the userspace.
In the case of semi planar formats cb and cr are in the same plane
in memory, meaning that will be set to 'cb' whatever the format is,
and whatever the (packed) order of those components are.
When the separate IRQ stack was introduced, stack unwinding only
proceeded as far as the top of the IRQ stack, leading to kernel
backtraces being less useful, lacking the trace of what was interrupted.
Fix this by providing a means for the kernel to unwind the IRQ stack
onto the interrupted task stack. The processor state is saved to the
kernel task stack on interrupt. The IRQ_STACK_START macro reserves an
unsigned long at the top of the IRQ stack where the interrupted task
stack pointer can be saved. After the active stack is switched to the
IRQ stack, save the interrupted tasks stack pointer to the reserved
location.
Fix the stack unwinding code to look for the frame being the top of the
IRQ stack and if so get the next frame from the saved location. The
existing test does not work with the separate stack since the ra is no
longer pointed at ret_from_{irq,exception}.
The test to stop unwinding the stack 32 bytes from the top of a stack
must be modified to allow unwinding to continue up to the location of
the saved task stack pointer when on the IRQ stack. The low / high marks
of the stack are set depending on whether the sp is on an irq stack or
not.
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com> Cc: Paolo Bonzini <pbonzini@redhat.com> Cc: Marcin Nowakowski <marcin.nowakowski@imgtec.com> Cc: Masanari Iida <standby24x7@gmail.com> Cc: Chris Metcalf <cmetcalf@mellanox.com> Cc: James Hogan <james.hogan@imgtec.com> Cc: Paul Burton <paul.burton@imgtec.com> Cc: Ingo Molnar <mingo@kernel.org> Cc: Jason A. Donenfeld <jason@zx2c4.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/15788/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Otherwise, another CPU may access the invalid pointer. For example:
CPU0 CPU1
- rcu_read_lock();
- pfunc = _hook_;
_hook_ = NULL; -
mod unload -
- pfunc(); // invalid, panic
- rcu_read_unlock();
So we must call synchronize_rcu() to wait the rcu reader to finish.
Also note, in nf_nat_snmp_basic_fini, synchronize_rcu() will be invoked
by later nf_conntrack_helper_unregister, but I'm inclined to add a
explicit synchronize_rcu after set the nf_nat_snmp_hook to NULL. Depend
on such obscure assumptions is not a good idea.
Last, in nfnetlink_cttimeout, we use kfree_rcu to free the time object,
so in cttimeout_exit, invoking rcu_barrier() is not necessary at all,
remove it too.
The problem is that the bridge's VLAN group is created after setting the
default PVID, when registering the netdevice and executing its
ndo_init().
Fix this by changing the order of both operations, so that
br_changelink() is only processed after the netdevice is registered,
when the VLAN group is already initialized.
Fixes: b6677449dff6 ("bridge: netlink: call br_changelink() during br_dev_newlink()") Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Reported-by: Peter V. Saveliev <peter@svinota.eu> Tested-by: Peter V. Saveliev <peter@svinota.eu> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Certain 64-bit systems (e.g. Amlogic Meson GX) require buffers to be
used for DMA to be 8-byte-aligned. struct sdio_func has an embedded
small DMA buffer not meeting this requirement.
When testing switching to descriptor chain mode in meson-gx driver
SDIO is broken therefore. Fix this by allocating the small DMA buffer
separately as kmalloc ensures that the returned memory area is
properly aligned for every basic data type.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Tested-by: Helmut Klein <hgkr.klein@gmail.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds support for the PL-27A1 by adding the appropriate
USB ID's. This chip is used in the goobay Active USB 3.0 Data Link
and Unitek Y-3501 cables.
Signed-off-by: Roman Spychała <roed@onet.eu> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In functions team_nl_send_port_list_get() and
team_nl_send_options_get(), pointer skb keeps the return value of
nlmsg_new(). When the call to genlmsg_put() fails, the memory is not
freed(). This will result in memory leak bugs.
Fixes: 9b00cf2d1024 ("team: implement multipart netlink messages for options transfers") Signed-off-by: Pan Bian <bianpan2016@163.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the case getsockopt() is called with PACKET_HDRLEN and optlen < 4
|val| remains uninitialized and the syscall may behave differently
depending on its value, and even copy garbage to userspace on certain
architectures. To fix this we now return -EINVAL if optlen is too small.
This bug has been detected with KMSAN.
Signed-off-by: Alexander Potapenko <glider@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hauke already fixed a couple of them, but one instance remains
that checks for a negative integer when it should check
for a NULL pointer:
arch/mips/lantiq/xway/sysctrl.c: In function 'ltq_soc_init':
arch/mips/lantiq/xway/sysctrl.c:473:19: error: ordered comparison of pointer with integer zero [-Werror=extra]
Fixes: 6e807852676a ("MIPS: Lantiq: Fix check for return value of request_mem_region()") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Cc: John Crispin <john@phrozen.org> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/15043/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 66feeec9322132689d42723df2537d60f96f8e44
"RFC: ASoC: dapm: handle probe deferrals"
forgot a to update some two sites where the call
was used. The static codechecks quickly found them.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Fixes: 66feeec93221 ("RFC: ASoC: dapm: handle probe deferrals") Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At some situations, the vbus may already be there before starting
gadget. So we need to check vbus event after switching to gadget in
order to handle missing vbus event. The typical use cases are plugging
vbus cable before driver load or the vbus has already been there
after stopping host but before starting gadget.
Signed-off-by: Peter Chen <peter.chen@nxp.com> Tested-by: Stephen Boyd <stephen.boyd@linaro.org> Reported-by: Stephen Boyd <stephen.boyd@linaro.org> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
32-bit socketcalls were not being logged by audit on x86_64 systems.
Log them. This is basically a duplicate of the call from
net/socket.c:sys_socketcall(), but it addresses the impedance mismatch
between 32-bit userspace process and 64-bit kernel audit.
Signed-off-by: Richard Guy Briggs <rgb@redhat.com> Acked-by: David S. Miller <davem@davemloft.net> Signed-off-by: Paul Moore <paul@paul-moore.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This starts to handle probe deferrals on regulators and clocks
on the ASoC DAPM.
I came to this patch after audio stopped working on Ux500 ages
ago and I finally looked into it to see what is wrong. I had
messages like this in the console since a while back:
ab8500-codec.0: ASoC: Failed to request audioclk: -517
ab8500-codec.0: ASoC: Failed to create DAPM control audioclk
ab8500-codec.0: Failed to create new controls -12
snd-soc-mop500.0: ASoC: failed to instantiate card -12
snd-soc-mop500.0: Error: snd_soc_register_card failed (-12)!
snd-soc-mop500: probe of snd-soc-mop500.0 failed with error -12
Apparently because the widget table for the codec looks like
this (sound/soc/codecs/ab8500-codec.c):
So when we call snd_soc_register_codec() and any of these widgets
get a deferred probe we do not get an -EPROBE_DEFER (-517) back as
we should and instead we just fail. Apparently the code assumes
that clocks and regulators must be available at this point and
not defer.
After this patch it rather looks like this:
ab8500-codec.0: Failed to create new controls -517
snd-soc-mop500.0: ASoC: failed to instantiate card -517
snd-soc-mop500.0: Error: snd_soc_register_card failed (-517)!
(...)
abx500-clk.0: registered clocks for ab850x
snd-soc-mop500.0: ab8500-codec-dai.0 <-> ux500-msp-i2s.1 mapping ok
snd-soc-mop500.0: ab8500-codec-dai.1 <-> ux500-msp-i2s.3 mapping ok
I'm pretty happy about the patch as it it, but I'm a bit
uncertain on how to proceed: there are a lot of users of the
external functions snd_soc_dapm_new_control() (111 sites)
and that will now return an occassional error pointer, which
is not handled in the calling sites.
I want an indication from the maintainers whether I should just
go in and augment all these call sites, or if deferred probe
is frowned upon when it leads to this much overhead.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a GUID Partition Table claims to have more than 2**25 entries, the
calculation of the partition table size in alloc_read_gpt_entries() will
overflow a 32-bit integer and not enough space will be allocated for the
table.
Nothing seems to get written out of bounds, but later efi_partition() will
read up to 32768 bytes from a 128 byte buffer, possibly OOPSing or exposing
information to /proc/partitions and uevents.
The problem exists on both 64-bit and 32-bit platforms.
Fix the overflow and also print a meaningful debug message if the table
size is too large.
Make sure to detect short transfers when reading a device register.
The modem-status handling had sufficient error checks in place, but move
handling of short transfers into the register accessor function itself
for consistency.
Make sure to log an error on short transfers when reading a device
register.
Also clear the provided buffer (which if often an uninitialised
automatic variable) on errors as the driver currently does not bother to
check for errors.
In function kfd_wait_on_events(), when the call to copy_from_user()
fails, the value of return variable ret is 0. 0 indicates success, which
is inconsistent with the execution status. This patch fixes the bug by
assigning "-EFAULT" to ret when copy_from_user() returns an unexpected
value.
In order to resolve a situation where a few process delete
the same list element in sequence and cause panic, list_del
is replaced with list_del_init. In this case if the first
process that calls list_del releases the lock before acquiring
it again, other processes who can acquire the lock will call
list_del_init.
Fixes: b63b70d87741 ("IPoIB: Use a private hash table for path lookup") Signed-off-by: Feras Daoud <ferasda@mellanox.com> Signed-off-by: Erez Shitrit <erezsh@mellanox.com> Reviewed-by: Alex Vesker <valex@mellanox.com> Signed-off-by: Leon Romanovsky <leon@kernel.org> Reviewed-by: Yuval Shaia <yuval.shaia@oracle.com> Signed-off-by: Doug Ledford <dledford@redhat.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ipoib_vlan_add function calls rtnl_unlock after free_netdev,
rtnl_unlock not only releases the lock, but also calls netdev_run_todo.
The latter function browses the net_todo_list array and completes the
unregistration of all its net_device instances. If we call free_netdev
before rtnl_unlock, then netdev_run_todo call over the freed device causes
panic.
To fix, move rtnl_unlock call before free_netdev call.
This patch fixes Deadlock while executing ipoib_vlan_delete.
The function takes the vlan_rwsem semaphore and calls
unregister_netdevice. The later function calls
ipoib_mcast_stop_thread that cause workqueue flush.
When the queue has one of the ipoib_ib_dev_flush_xxx events,
a deadlock occur because these events also tries to catch the
same vlan_rwsem semaphore.
To fix, unregister_netdevice should be called after releasing
the semaphore.
Fixes: cbbe1efa4972 ("IPoIB: Fix deadlock between ipoib_open() and child interface create") Signed-off-by: Feras Daoud <ferasda@mellanox.com> Signed-off-by: Erez Shitrit <erezsh@mellanox.com> Reviewed-by: Alex Vesker <valex@mellanox.com> Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Doug Ledford <dledford@redhat.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
REMAP_VECTORS_TO_RAM depends on DRAM_BASE, but since DRAM_BASE is a
hex, REMAP_VECTORS_TO_RAM could never get enabled. Also depending on
DRAM_BASE is redundant as whenever REMAP_VECTORS_TO_RAM makes itself
available to Kconfig, DRAM_BASE also is available as the Kconfig
gets sourced on !MMU.
Signed-off-by: Afzal Mohammed <afzal.mohd.ma@gmail.com> Reviewed-by: Vladimir Murzin <vladimir.murzin@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For some reason the axp288_adc driver was modifying the
AXP288_ADC_TS_PIN_CTRL register, changing bits 0-1 depending on
whether the GP_ADC channel or another channel was written.
These bits control when a bias current is send to the TS_PIN, the
GP_ADC has its own pin and a separate bit in another register to
control the bias current.
Not only does changing when to enable the TS_PIN bias current
(always or only when sampling) when reading the GP_ADC make no sense
at all, the code is modifying these bits is writing the entire register,
assuming that all the other bits have their default value.
So if the firmware has configured a different bias-current for either
pin, then that change gets clobbered by the write, likewise if the
firmware has set bit 2 to indicate that the battery has no thermal sensor,
this will get clobbered by the write.
This commit fixes all this, by simply removing all writes to the
AXP288_ADC_TS_PIN_CTRL register, they are not needed to read the
GP_ADC pin, and can actually be harmful.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Writes into limit attributes can overflow due to multplications and
additions with unbound input values. Writing into fan limit attributes
can result in a crash with a division by zero if very large values are
written and the fan divider is larger than 1.
The vbus-present bit in the power status register also gets set to 1
when a usb-host cable (id-pin shorted to ground) is plugged in and a 5v
boost converter is supplying 5v to the otg usb bus.
This causes a "disconnect or unknown or ID event" warning in dmesg as
well as the extcon device to report the last detected charger cable
type as being connected even though none is connected.
This commit switches to checking the vbus-valid bit instead, which is
only 1 when both vbus is present and the vbus-path is enabled in the
vbus-path control register (the vbus-path gets disabled when a usb-host
cable is detected, to avoid the pmic drawing power from the 5v boost
converter).
Whenever the igb driver detects the result of a read operation returns
a value composed only by F's (like 0xFFFFFFFF), it will detach the
net_device, clear the hw_addr pointer and warn to the user that adapter's
link is lost - those steps happen on igb_rd32().
In case a PCI error happens on Power architecture, there's a recovery
mechanism called EEH, that will reset the PCI slot and call driver's
handlers to reset the adapter and network functionality as well.
We observed that once hw_addr is NULL after the error is detected on
igb_rd32(), it's never assigned back, so in the process of resetting
the network functionality we got a NULL pointer dereference in both
igb_configure_tx_ring() and igb_configure_rx_ring(). In order to avoid
such bug, this patch re-assigns the hw_addr value in the slot_reset
handler.
Reported-by: Anthony H Thai <ahthai@us.ibm.com> Reported-by: Harsha Thyagaraja <hathyaga@in.ibm.com> Signed-off-by: Guilherme G Piccoli <gpiccoli@linux.vnet.ibm.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When clearing the .bss section in kernel_entry we do so using LONG_S
instructions, and branch whilst the current write address doesn't equal
the end of the .bss section minus the size of a long integer. The .bss
section always begins at a long-aligned address and we always increment
the write pointer by the size of a long integer - we therefore rely upon
the .bss section ending at a long-aligned address. If this is not the
case then the long-aligned write address can never be equal to the
non-long-aligned end address & we will continue to increment past the
end of the .bss section, attempting to zero the rest of memory.
Despite this requirement that .bss end at a long-aligned address we pass
0 as the end alignment requirement to the BSS_SECTION macro and thus
don't guarantee any particular alignment, allowing us to hit the error
condition described above.
Fix this by instead passing 8 bytes as the end alignment argument to
the BSS_SECTION macro, ensuring that the end of the .bss section is
always at least long-aligned.
Use recently added R-Car Gen 2 fallback binding for msiof nodes in
DT for r8a7790 SoC.
This has no run-time effect for the current driver as the initialisation
sequence is the same for the SoC-specific binding for r8a7790 and the
fallback binding for R-Car Gen 2.
When application sends an RDS RDMA composite message consist of
RDMA transfer to be followed up by non RDMA payload, it expect to
be notified *only* when the full message gets delivered. RDS RDMA
notification doesn't behave this way though.
Thanks to Venkat for debug and root casuing the issue
where only first part of the message(RDMA) was
successfully delivered but remainder payload delivery failed.
In that case, application should not be notified with
a false positive of message delivery success.
Fix this case by making sure the user gets notified only after
the full message delivery.
Arnd Bergmann [Wed, 4 Oct 2017 13:51:29 +0000 (15:51 +0200)]
fix xen_swiotlb_dma_mmap prototype
xen_swiotlb_dma_mmap was backported from v4.10, but older
kernels before commit 00085f1efa38 ("dma-mapping: use unsigned long
for dma_attrs") use a different signature:
arm/xen/mm.c:202:10: error: initialization from incompatible pointer type [-Werror=incompatible-pointer-types]
.mmap = xen_swiotlb_dma_mmap,
^~~~~~~~~~~~~~~~~~~~
arm/xen/mm.c:202:10: note: (near initialization for 'xen_swiotlb_dma_ops.mmap')
This adapts the patch to the old calling conventions.
'clk' is copied to a userland with padding byte(s) after 'vclk_post_div'
field unitialized, leaking data from the stack. Fix this ensuring all of
'clk' is initialized to zero.
The number of requestor lines was clamped to 0 for all pxa architectures
in the requestor declaration. Fix this by using the value.
Fixes: 72b195cb7162 ("ARM: pxa: add the number of DMA requestor lines") Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Declare the number of DMA requestor lines per platform :
- for pxa25x: 40 requestor lines
- for pxa27x: 75 requestor lines
- for pxa3xx: 100 requestor lines
This information will be used to activate the DMA flow control or not.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The DMA chip has a fixed number of requestor lines used for flow
control. This number is platform dependent. The pxa_dma dma driver will
use this value to activate or not the flow control.
There won't be any impact on mmp_pdma driver.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
cxl keeps a driver use count, which is used with the hash memory model
on p8 to know when to upgrade local TLBIs to global and to trigger
callbacks to manage the MMU for PSL8.
If a process opens a context and closes without attaching or fails the
attachment, the driver use count is never decremented. As a
consequence, TLB invalidations remain global, even if there are no
active cxl contexts.
We should increment the driver use count when the process is attaching
to the cxl adapter, and not on open. It's not needed before the
adapter starts using the context and the use count is decremented on
the detach path, so it makes more sense.
It affects only the user api. The kernel api is already doing The
Right Thing.
Signed-off-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com> Fixes: 7bb5d91a4dda ("cxl: Rework context lifetimes") Acked-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
[ajd: backport to stable v4.4 tree] Signed-off-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
WARN_ON_ONCE(pi_test_sn(&vmx->pi_desc)) in kvm_vcpu_trigger_posted_interrupt()
intends to detect the violation of invariant that VT-d PI notification
event is not suppressed when vcpu is in the guest mode. Because the
two checks for the target vcpu mode and the target suppress field
cannot be performed atomically, the target vcpu mode may change in
between. If that does happen, WARN_ON_ONCE() here may raise false
alarms.
As the previous patch fixed the real invariant breaker, remove this
WARN_ON_ONCE() to avoid false alarms, and document the allowed cases
instead.
Signed-off-by: Haozhong Zhang <haozhong.zhang@intel.com> Reported-by: "Ramamurthy, Venkatesh" <venkatesh.ramamurthy@intel.com> Reported-by: Dan Williams <dan.j.williams@intel.com> Reviewed-by: Paolo Bonzini <pbonzini@redhat.com> Fixes: 28b835d60fcc ("KVM: Update Posted-Interrupts Descriptor when vCPU is preempted") Signed-off-by: Radim Krčmář <rkrcmar@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In kvm_vcpu_trigger_posted_interrupt() and pi_pre_block(), KVM
assumes that PI notification events should not be suppressed when the
target vCPU is not blocked.
vmx_update_pi_irte() sets the SN field before changing an interrupt
from posting to remapping, but it does not check the vCPU mode.
Therefore, the change of SN field may break above the assumption.
Besides, I don't see reasons to suppress notification events here, so
remove the changes of SN field to avoid race condition.
Signed-off-by: Haozhong Zhang <haozhong.zhang@intel.com> Reported-by: "Ramamurthy, Venkatesh" <venkatesh.ramamurthy@intel.com> Reported-by: Dan Williams <dan.j.williams@intel.com> Reviewed-by: Paolo Bonzini <pbonzini@redhat.com> Fixes: 28b835d60fcc ("KVM: Update Posted-Interrupts Descriptor when vCPU is preempted") Signed-off-by: Radim Krčmář <rkrcmar@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The switch to rhashtables (commit 88ffbf3e03) broke the debugfs glock
dump (/sys/kernel/debug/gfs2/<device>/glocks) for dumps bigger than a
single buffer: the right function for restarting an rhashtable iteration
from the beginning of the hash table is rhashtable_walk_enter;
rhashtable_walk_stop + rhashtable_walk_start will just resume from the
current position.
The upstream commit doesn't directly apply to 4.4.y because 4.4.y
doesn't have rhashtable_walk_enter and the following mainline commits:
Other than rhashtable_walk_enter, rhashtable_walk_init can fail. To
handle the failure case in gfs2_glock_seq_stop, we check if
rhashtable_walk_init has initialized iter->walker; if it has not, we
must not call rhashtable_walk_stop or rhashtable_walk_exit.
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com> Signed-off-by: Bob Peterson <rpeterso@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[Please apply to 4.4-stable. Note: the backport includes the
fpstate_init() call in xstateregs_set(), since fix is useless without
it. It was added by commit 91c3dba7dbc1 ("x86/fpu/xstate: Fix PTRACE
frames for XSAVES"), but it doesn't make sense to backport that whole
commit.]
On x86, userspace can use the ptrace() or rt_sigreturn() system calls to
set a task's extended state (xstate) or "FPU" registers. ptrace() can
set them for another task using the PTRACE_SETREGSET request with
NT_X86_XSTATE, while rt_sigreturn() can set them for the current task.
In either case, registers can be set to any value, but the kernel
assumes that the XSAVE area itself remains valid in the sense that the
CPU can restore it.
However, in the case where the kernel is using the uncompacted xstate
format (which it does whenever the XSAVES instruction is unavailable),
it was possible for userspace to set the xcomp_bv field in the
xstate_header to an arbitrary value. However, all bits in that field
are reserved in the uncompacted case, so when switching to a task with
nonzero xcomp_bv, the XRSTOR instruction failed with a #GP fault. This
caused the WARN_ON_FPU(err) in copy_kernel_to_xregs() to be hit. In
addition, since the error is otherwise ignored, the FPU registers from
the task previously executing on the CPU were leaked.
Fix the bug by checking that the user-supplied value of xcomp_bv is 0 in
the uncompacted case, and returning an error otherwise.
The reason for validating xcomp_bv rather than simply overwriting it
with 0 is that we want userspace to see an error if it (incorrectly)
provides an XSAVE area in compacted format rather than in uncompacted
format.
Note that as before, in case of error we clear the task's FPU state.
This is perhaps non-ideal, especially for PTRACE_SETREGSET; it might be
better to return an error before changing anything. But it seems the
"clear on error" behavior is fine for now, and it's a little tricky to
do otherwise because it would mean we couldn't simply copy the full
userspace state into kernel memory in one __copy_from_user().
This bug was found by syzkaller, which hit the above-mentioned
WARN_ON_FPU():
Here is a C reproducer. The expected behavior is that the program spin
forever with no output. However, on a buggy kernel running on a
processor with the "xsave" feature but without the "xsaves" feature
(e.g. Sandy Bridge through Broadwell for Intel), within a second or two
the program reports that the xmm registers were corrupted, i.e. were not
restored correctly. With CONFIG_X86_DEBUG_FPU=y it also hits the above
kernel warning.
Note: the program only tests for the bug using the ptrace() system call.
The bug can also be reproduced using the rt_sigreturn() system call, but
only when called from a 32-bit program, since for 64-bit programs the
kernel restores the FPU state from the signal frame by doing XRSTOR
directly from userspace memory (with proper error checking).
Reported-by: Dmitry Vyukov <dvyukov@google.com> Signed-off-by: Eric Biggers <ebiggers@google.com> Reviewed-by: Kees Cook <keescook@chromium.org> Reviewed-by: Rik van Riel <riel@redhat.com> Acked-by: Dave Hansen <dave.hansen@linux.intel.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Andy Lutomirski <luto@amacapital.net> Cc: Andy Lutomirski <luto@kernel.org> Cc: Borislav Petkov <bp@alien8.de> Cc: Eric Biggers <ebiggers3@gmail.com> Cc: Fenghua Yu <fenghua.yu@intel.com> Cc: Kevin Hao <haokexin@gmail.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Michael Halcrow <mhalcrow@google.com> Cc: Oleg Nesterov <oleg@redhat.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Wanpeng Li <wanpeng.li@hotmail.com> Cc: Yu-cheng Yu <yu-cheng.yu@intel.com> Cc: kernel-hardening@lists.openwall.com Fixes: 0b29643a5843 ("x86/xsaves: Change compacted format xsave area header") Link: http://lkml.kernel.org/r/20170922174156.16780-2-ebiggers3@gmail.com Link: http://lkml.kernel.org/r/20170923130016.21448-25-mingo@kernel.org Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
`btrfs sub set-default` succeeds to set an ID which isn't corresponding to any
fs/file tree. If such the bad ID is set to a filesystem, we can't mount this
filesystem without specifying `subvol` or `subvolid` mount options.
Fixes: 6ef5ed0d386b ("Btrfs: add ioctl and incompat flag to set the default mount subvol") Signed-off-by: Satoru Takeuchi <satoru.takeuchi@gmail.com> Reviewed-by: Qu Wenruo <quwenruo.btrfs@gmx.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
btrfs_cmp_data_prepare() (almost) always returns 0 i.e. ignoring errors
from gather_extent_pages(). While the pages are freed by
btrfs_cmp_data_free(), cmp->num_pages still has > 0. Then,
btrfs_extent_same() try to access the already freed pages causing faults
(or violates PageLocked assertion).
This patch just return the error as is so that the caller stop the process.
Signed-off-by: Naohiro Aota <naohiro.aota@wdc.com> Fixes: f441460202cb ("btrfs: fix deadlock with extent-same and readpage") Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
__del_reloc_root should be called before freeing up reloc_root->node.
If not, calling __del_reloc_root() dereference reloc_root->node, causing
the system BUG.
Fixes: 6bdf131fac23 ("Btrfs: don't leak reloc root nodes on error") Signed-off-by: Naohiro Aota <naohiro.aota@wdc.com> Reviewed-by: Nikolay Borisov <nborisov@suse.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver_override implementation is susceptible to a race condition when
different threads are reading vs. storing a different driver override. Add
locking to avoid the race condition.
This is in close analogy to commit 6265539776a0 ("driver core: platform:
fix race condition with driver_override") from Adrian Salido.
If L1 does not specify the "use TPR shadow" VM-execution control in
vmcs12, then L0 must specify the "CR8-load exiting" and "CR8-store
exiting" VM-execution controls in vmcs02. Failure to do so will give
the L2 VM unrestricted read/write access to the hardware CR8.
This fixes CVE-2017-12154.
Signed-off-by: Jim Mattson <jmattson@google.com> Reviewed-by: David Hildenbrand <david@redhat.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The value of the guest_irq argument to vmx_update_pi_irte() is
ultimately coming from a KVM_IRQFD API call. Do not BUG() in
vmx_update_pi_irte() if the value is out-of bounds. (Especially,
since KVM as a whole seems to hang after that.)
Instead, print a message only once if we find that we don't have a
route for a certain IRQ (which can be out-of-bounds or within the
array).
We currently route pte translation faults via do_page_fault, which elides
the address check against TASK_SIZE before invoking the mm fault handling
code. However, this can cause issues with the path walking code in
conjunction with our word-at-a-time implementation because
load_unaligned_zeropad can end up faulting in kernel space if it reads
across a page boundary and runs into a page fault (e.g. by attempting to
read from a guard region).
In the case of such a fault, load_unaligned_zeropad has registered a
fixup to shift the valid data and pad with zeroes, however the abort is
reported as a level 3 translation fault and we dispatch it straight to
do_page_fault, despite it being a kernel address. This results in calling
a sleeping function from atomic context:
When the kernel is entered at EL2 on an ARMv8.0 system, we construct
the EL1 pstate and make sure this uses the the EL1 stack pointer
(we perform an exception return to EL1h).
But if the kernel is either entered at EL1 or stays at EL2 (because
we're on a VHE-capable system), we fail to set SPsel, and use whatever
stack selection the higher exception level has choosen for us.
Let's not take any chance, and make sure that SPsel is set to one
before we decide the mode we're going to run in.
Acked-by: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As Chris explains, get_seccomp_filter() and put_seccomp_filter() can end
up using different filters. Once we drop ->siglock it is possible for
task->seccomp.filter to have been replaced by SECCOMP_FILTER_FLAG_TSYNC.
Fixes: f8e529ed941b ("seccomp, ptrace: add support for dumping seccomp filters") Reported-by: Chris Salls <chrissalls5@gmail.com> Signed-off-by: Oleg Nesterov <oleg@redhat.com>
[tycho: add __get_seccomp_filter vs. open coding refcount_inc()] Signed-off-by: Tycho Andersen <tycho@docker.com>
[kees: tweak commit log] Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
nl80211_set_rekey_data() does not check if the required attributes
NL80211_REKEY_DATA_{REPLAY_CTR,KEK,KCK} are present when processing
NL80211_CMD_SET_REKEY_OFFLOAD request. This request can be issued by
users with CAP_NET_ADMIN privilege and may result in NULL dereference
and a system crash. Add a check for the required attributes presence.
This patch is based on the patch by bo Zhang.
This fixes CVE-2017-12153.
References: https://bugzilla.redhat.com/show_bug.cgi?id=1491046 Fixes: e5497d766ad ("cfg80211/nl80211: support GTK rekey offload") Reported-by: bo Zhang <zhangbo5891001@gmail.com> Signed-off-by: Vladis Dronov <vdronov@redhat.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In generic_file_llseek_size, return -ENXIO for negative offsets as well
as offsets beyond EOF. This affects filesystems which don't implement
SEEK_HOLE / SEEK_DATA internally, possibly because they don't support
holes.
Signed-off-by: Steve French <smfrench@gmail.com> Reviewed-by: Ronnie Sahlberg <lsahlber@redhat.com> Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As long as signing is supported (ie not a guest user connection) and
connection is SMB3 or SMB3.02, then validate negotiate (protect
against man in the middle downgrade attacks). We had been doing this
only when signing was required, not when signing was just enabled,
but this more closely matches recommended SMB3 behavior and is
better security. Suggested by Metze.
Signed-off-by: Steve French <smfrench@gmail.com> Reviewed-by: Jeremy Allison <jra@samba.org> Acked-by: Stefan Metzmacher <metze@samba.org> Reviewed-by: Ronnie Sahlberg <lsahlber@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Samba rejects SMB3.1.1 dialect (vers=3.1.1) negotiate requests from
the kernel client due to the two byte pad at the end of the negotiate
contexts.
Signed-off-by: Steve French <smfrench@gmail.com> Reviewed-by: Ronnie Sahlberg <lsahlber@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A reference to the parent device node is held by add_dt_node() for the
node to be added. If the call to dlpar_configure_connector() fails
add_dt_node() returns ENOENT and that reference is not freed.
Add a call to of_node_put(parent_dn) prior to bailing out after a
failed dlpar_configure_connector() call.
Fixes: 8d5ff320766f ("powerpc/pseries: Make dlpar_configure_connector parent node aware") Signed-off-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Because keyctl_read_key() looks up the key with no permissions
requested, it may find a negatively instantiated key. If the key is
also possessed, we went ahead and called ->read() on the key. But the
key payload will actually contain the ->reject_error rather than the
normal payload. Thus, the kernel oopses trying to read the
user_key_payload from memory address (int)-ENOKEY = 0x00000000ffffff82.
Fortunately the payload data is stored inline, so it shouldn't be
possible to abuse this as an arbitrary memory read primitive...
Reproducer:
keyctl new_session
keyctl request2 user desc '' @s
keyctl read $(keyctl show | awk '/user: desc/ {print $1}')
Fixes: 61ea0c0ba904 ("KEYS: Skip key state checks when checking for possession") Signed-off-by: Eric Biggers <ebiggers@google.com> Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is problematic because these "fake" keyrings won't have the right
permissions. In particular, the user who created them first will own
them and will have full access to them via the possessor permissions,
which can be used to compromise the security of a user's keys:
Fix it by marking user and user session keyrings with a flag
KEY_FLAG_UID_KEYRING. Then, when searching for a user or user session
keyring by name, skip all keyrings that don't have the flag set.
Fixes: 69664cf16af4 ("keys: don't generate user and user session keyrings unless they're accessed") Signed-off-by: Eric Biggers <ebiggers@google.com> Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Userspace can call keyctl_read() on a keyring to get the list of IDs of
keys in the keyring. But if the user-supplied buffer is too small, the
kernel would write the full list anyway --- which will corrupt whatever
userspace memory happened to be past the end of the buffer. Fix it by
only filling the space that is available.
Fixes: b2a4df200d57 ("KEYS: Expand the capacity of a keyring") Signed-off-by: Eric Biggers <ebiggers@google.com> Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's caused by skb_shared_info at the end of sk_buff was overwritten by
ISCSI_KEVENT_IF_ERROR when parsing nlmsg info from skb in iscsi_if_rx.
During the loop if skb->len == nlh->nlmsg_len and both are sizeof(*nlh),
ev = nlmsg_data(nlh) will acutally get skb_shinfo(SKB) instead and set a
new value to skb_shinfo(SKB)->nr_frags by ev->type.
This patch is to fix it by checking nlh->nlmsg_len properly there to
avoid over accessing sk_buff.
Reported-by: ChunYu Wang <chunwang@redhat.com> Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Chris Leech <cleech@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In release_stripe_plug(), if a stripe_head has its STRIPE_ON_UNPLUG_LIST
set, it indicates that this stripe_head is already in the raid5_plug_cb
list and release_stripe() would be called instead to drop a reference
count. Otherwise, the STRIPE_ON_UNPLUG_LIST bit would be set for this
stripe_head and it will get queued into the raid5_plug_cb list.
Since break_stripe_batch_list() did not preserve STRIPE_ON_UNPLUG_LIST,
A stripe could be re-added to plug list while it is still on that list
in the following situation. If stripe_head A is added to another
stripe_head B's batch list, in this case A will have its
batch_head != NULL and be added into the plug list. After that,
stripe_head B gets handled and called break_stripe_batch_list() to
reset all the batched stripe_head(including A which is still on
the plug list)'s state and reset their batch_head to NULL.
Before the plug list gets processed, if there is another write request
comes in and get stripe_head A, A will have its batch_head == NULL
(cleared by calling break_stripe_batch_list() on B) and be added to
plug list once again.
Signed-off-by: Dennis Yang <dennisyang@qnap.com> Signed-off-by: Shaohua Li <shli@fb.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We have a race condition in below scenario, say have 3 continuous stripes, sh1,
sh2 and sh3, sh1 is the stripe_head of sh2 and sh3:
CPU1 CPU2 CPU3
handle_stripe(sh3)
stripe_add_to_batch_list(sh3)
-> lock(sh2, sh3)
-> lock batch_lock(sh1)
-> add sh3 to batch_list of sh1
-> unlock batch_lock(sh1)
clear_batch_ready(sh1)
-> lock(sh1) and batch_lock(sh1)
-> clear STRIPE_BATCH_READY for all stripes in batch_list
-> unlock(sh1) and batch_lock(sh1)
->clear_batch_ready(sh3)
-->test_and_clear_bit(STRIPE_BATCH_READY, sh3)
--->return 0 as sh->batch == NULL
-> sh3->batch_head = sh1
-> unlock (sh2, sh3)
In CPU1, handle_stripe will continue handle sh3 even it's in batch stripe list
of sh1. By moving sh3->batch_head assignment in to batch_lock, we make it
impossible to clear STRIPE_BATCH_READY before batch_head is set.
Thanks Stephane for helping debug this tricky issue.
One convenient way to erase trace is "echo > trace". However, this
is currently broken if the current tracer is irqsoff tracer. This
is because irqsoff tracer use max_buffer as the default trace
buffer.
Set the max_buffer as the one to be cleared when it's the trace
buffer currently in use.
Link: http://lkml.kernel.org/r/1505754215-29411-1-git-send-email-byan@nvidia.com Cc: <mingo@redhat.com> Fixes: 4acd4d00f ("tracing: give easy way to clear trace buffer") Signed-off-by: Bo Yan <byan@nvidia.com> Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When reading data from trace_pipe, tracing_wait_pipe() performs a
check to see if tracing has been turned off after some data was read.
Currently, this check always looks at global trace state, but it
should be checking the trace instance where trace_pipe is located at.
Because of this bug, cat instances/i1/trace_pipe in the following
script will immediately exit instead of waiting for data:
projects / thirdparty / kernel / stable.git / log
