Currently, the firmware returns incorrect pdev_id information in
WMI_PDEV_BSS_CHAN_INFO_EVENTID, leading to incorrect filling of
the pdev's survey information.
To prevent this issue, when requesting BSS channel information
through WMI_PDEV_BSS_CHAN_INFO_REQUEST_CMDID, firmware expects
pdev_id as one of the arguments in this WMI command.
Add pdev_id to the struct wmi_pdev_bss_chan_info_req_cmd and fill it
during ath12k_wmi_pdev_bss_chan_info_request(). This resolves the
issue of sending the correct pdev_id in WMI_PDEV_BSS_CHAN_INFO_EVENTID.
We should not be checking the return values from debugfs creation at all: the
debugfs functions are designed to handle errors of previously called functions
and just transparently abort the creation of debugfs entries when debugfs is
disabled. If we check the return value and abort driver initialisation, we break
the driver if debugfs is disabled (such as when booting with debugfs=off).
Earlier versions of ath9k accidentally did the right thing by checking the
return value, but only for NULL, not for IS_ERR(). This was "fixed" by the two
commits referenced below, breaking ath9k with debugfs=off starting from the 6.6
kernel (as reported in the Bugzilla linked below).
Restore functionality by just getting rid of the return value check entirely.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=219122 Fixes: 1e4134610d93 ("wifi: ath9k: use IS_ERR() with debugfs_create_dir()") Fixes: 6edb4ba6fb5b ("wifi: ath9k: fix parameter check in ath9k_init_debug()") Reported-by: Daniel Tobias <dan.g.tob@gmail.com> Tested-by: Daniel Tobias <dan.g.tob@gmail.com> Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://patch.msgid.link/20240805110225.19690-1-toke@toke.dk Signed-off-by: Sasha Levin <sashal@kernel.org>
When the firmware interface layer was refactored it provided various
"get" and "set" functions. For the "get" in some cases a parameter
needed to be passed down to firmware as a key indicating what to
"get" turning the output parameter of the "get" function into an
input parameter as well. To accommodate this the "get" function blindly
copies the parameter which in some places resulted in an uninitialized
warnings from the compiler. These have been fixed by initializing the
input parameter in the past. Recently another batch of similar fixes
were submitted to address clang static checker warnings [1].
Proposing another solution by introducing a "query" variant which is used
when the (input) parameter is needed by firmware. The "get" variant will
only fill the (output) parameter with the result received from firmware
taking care of proper endianess conversion.
With multi-vendor support the vendor-specific module may need to use
the firmware interface functions so export them using the macro
BRCMF_EXPORT_SYMBOL_GPL() which exports them to driver namespace.
Commit c055e3eae0f1 ("crypto: xor - use ktime for template benchmarking")
switched from using jiffies to ktime-based performance benchmarking.
This works nicely on machines which have a fine-grained ktime()
clocksource as e.g. x86 machines with TSC.
But other machines, e.g. my 4-way HP PARISC server, don't have such
fine-grained clocksources, which is why it seems that 800 xor loops
take zero seconds, which then shows up in the logs as:
Fix this with some small modifications to the existing code to improve
the algorithm to always produce correct results without introducing
major delays for architectures with a fine-grained ktime()
clocksource:
a) Delay start of the timing until ktime() just advanced. On machines
with a fast ktime() this should be just one additional ktime() call.
b) Count the number of loops. Run at minimum 800 loops and finish
earliest when the ktime() counter has progressed.
With that the throughput can now be calculated more accurately under all
conditions.
Fixes: c055e3eae0f1 ("crypto: xor - use ktime for template benchmarking") Signed-off-by: Helge Deller <deller@gmx.de> Tested-by: John David Anglin <dave.anglin@bell.net>
v2:
- clean up coding style (noticed & suggested by Herbert Xu)
- rephrased & fixed typo in commit message
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
In 'rtw_wait_firmware_completion()', always wait for both (regular and
wowlan) firmware loading attempts. Otherwise if 'rtw_usb_intf_init()'
has failed in 'rtw_usb_probe()', 'rtw_usb_disconnect()' may issue
'ieee80211_free_hw()' when one of 'rtw_load_firmware_cb()' (usually
the wowlan one) is still in progress, causing UAF detected by KASAN.
The Zynq UltraScale+ MPSoC DDR has a disjoint memory from 2GB to 32GB.
The DDR host interface has a contiguous memory so while injecting
errors, the driver should remove the hole else the injection fails as
the address translation is incorrect.
Introduce a get_mem_info() function pointer and set it for Zynq
UltraScale+ platform to return host address.
The race condition around the ECCCLR register access happens in the IRQ
disable method called in the device remove() procedure and in the ECC IRQ
handler:
1. Enable IRQ:
a. ECCCLR = EN_CE | EN_UE
2. Disable IRQ:
a. ECCCLR = 0
3. IRQ handler:
a. ECCCLR = CLR_CE | CLR_CE_CNT | CLR_CE | CLR_CE_CNT
b. ECCCLR = 0
c. ECCCLR = EN_CE | EN_UE
So if the IRQ disabling procedure is called concurrently with the IRQ
handler method the IRQ might be actually left enabled due to the
statement 3c.
The root cause of the problem is that ECCCLR register (which since
v3.10a has been called as ECCCTL) has intermixed ECC status data clear
flags and the IRQ enable/disable flags. Thus the IRQ disabling (clear EN
flags) and handling (write 1 to clear ECC status data) procedures must
be serialised around the ECCCTL register modification to prevent the
race.
So fix the problem described above by adding the spin-lock around the
ECCCLR modifications and preventing the IRQ-handler from modifying the
IRQs enable flags (there is no point in disabling the IRQ and then
re-enabling it again within a single IRQ handler call, see the
statements 3a/3b and 3c above).
Fixes: f7824ded4149 ("EDAC/synopsys: Add support for version 3 of the Synopsys EDAC DDR") Signed-off-by: Serge Semin <fancer.lancer@gmail.com> Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de> Link: https://lore.kernel.org/r/20240222181324.28242-2-fancer.lancer@gmail.com
Stable-dep-of: 35e6dbfe1846 ("EDAC/synopsys: Fix error injection on Zynq UltraScale+") Signed-off-by: Sasha Levin <sashal@kernel.org>
The mcp251xfd wakes up from Low Power or Sleep Mode when SPI activity
is detected. To avoid this, make sure that the timestamp worker is
stopped before shutting down the chip.
Split the starting of the timestamp worker out of
mcp251xfd_timestamp_init() into the separate function
mcp251xfd_timestamp_start().
Call mcp251xfd_timestamp_init() before mcp251xfd_chip_start(), move
mcp251xfd_timestamp_start() to mcp251xfd_chip_start(). In this way,
mcp251xfd_timestamp_stop() can be called unconditionally by
mcp251xfd_chip_stop().
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
New CPU #defines encode vendor and family as well as model.
[ dhansen: vertically align 0's in invlpg_miss_ids[] ]
Signed-off-by: Tony Luck <tony.luck@intel.com> Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com> Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de> Link: https://lore.kernel.org/all/20240424181518.41946-1-tony.luck%40intel.com
[ Ricardo: I used the old match macro X86_MATCH_INTEL_FAM6_MODEL()
instead of X86_MATCH_VFM() as in the upstream commit. ] Signed-off-by: Ricardo Neri <ricardo.neri-calderon@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Another device has been reported to be unreliable if we have more than
one outstanding command. In this new case, data corruption may occur.
Since we have two devices now needing this quirky behavior, make a
generic quirk flag.
The same Apple quirk is clearly not "temporary", so update the comment
while moving it.
linereq_set_config() behaves badly when direction is not set.
The configuration validation is borrowed from linereq_create(), where,
to verify the intent of the user, the direction must be set to in order to
effect a change to the electrical configuration of a line. But, when
applied to reconfiguration, that validation does not allow for the unset
direction case, making it possible to clear flags set previously without
specifying the line direction.
Adding to the inconsistency, those changes are not immediately applied by
linereq_set_config(), but will take effect when the line value is next get
or set.
For example, by requesting a configuration with no flags set, an output
line with GPIO_V2_LINE_FLAG_ACTIVE_LOW and GPIO_V2_LINE_FLAG_OPEN_DRAIN
set could have those flags cleared, inverting the sense of the line and
changing the line drive to push-pull on the next line value set.
Skip the reconfiguration of lines for which the direction is not set, and
only reconfigure the lines for which direction is set.
Fixes: a54756cb24ea ("gpiolib: cdev: support GPIO_V2_LINE_SET_CONFIG_IOCTL") Signed-off-by: Kent Gibson <warthog618@gmail.com> Link: https://lore.kernel.org/r/20240626052925.174272-3-warthog618@gmail.com Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add missing decorator type to lookup expression and tighten WARN_ON_ONCE
check in pipapo to spot earlier that this is unset.
Fixes: 29b359cf6d95 ("netfilter: nft_set_pipapo: walk over current view on netlink dump") Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The generation mask can be updated while netlink dump is in progress.
The pipapo set backend walk iterator cannot rely on it to infer what
view of the datastructure is to be used. Add notation to specify if user
wants to read/update the set.
Based on patch from Florian Westphal.
Fixes: 2b84e215f874 ("netfilter: nft_set_pipapo: .walk does not deal with generations") Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
to match traffic from a process that got added to "foo" via
"echo $pid > /sys/fs/cgroup/foo/cgroup.procs".
However, 'level 3' is needed to make this work.
Seen from initial namespace, the complete hierarchy is:
% stat /sys/fs/cgroup/system.slice/docker-.../foo
Device: 0,21 Inode: 2264 ..
i.e. hierarchy is
0 1 2 3
/ -> system.slice -> docker-1... -> foo
... but the container doesn't know that its "/" is the "docker-1.."
cgroup. Current code will retrieve the 'system.slice' cgroup node
and store its kn->id in the destination register, so compare with
2264 ("foo" cgroup id) will not match.
Fetch "/" cgroup from ->init() and add its level to the level we try to
extract. cgroup root-level is 0 for the init-namespace or the level
of the ancestor that is exposed as the cgroup root inside the container.
In the above case, cgrp->level of "/" resolved in the container is 2
(docker-1...scope/) and request for 'level 1' will get adjusted
to fetch the actual level (3).
v2: use CONFIG_SOCK_CGROUP_DATA, eval function depends on it.
(kernel test robot)
Cc: cgroups@vger.kernel.org Fixes: e0bb96db96f8 ("netfilter: nft_socket: add support for cgroupsv2") Reported-by: Nadia Pinaeva <n.m.pinaeva@gmail.com> Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Having a limit of 64 DRM devices is not good enough for modern world
where we have multi-GPU servers, SR-IOV virtual functions and virtual
devices used for testing.
Let's utilize full minor range for DRM devices.
To avoid regressing the existing userspace, we're still maintaining the
numbering scheme where 0-63 is used for primary, 64-127 is reserved
(formerly for control) and 128-191 is used for render.
For minors >= 192, we're allocating minors dynamically on a first-come,
first-served basis.
Accel minor management is based on DRM (and is also using struct
drm_minor internally), since DRM is using XArray for minors, it makes
sense to also convert accel.
As the two implementations are identical (only difference being the
underlying xarray), move the accel_minor_* functionality to DRM.
IDR is deprecated, and since XArray manages its own state with internal
locking, it simplifies the locking on DRM side.
Additionally, don't use the IRQ-safe variant, since operating on drm
minor is not done in IRQ context.
Suggested-by: Matthew Wilcox <willy@infradead.org> Signed-off-by: Michał Winiarski <michal.winiarski@intel.com> Acked-by: James Zhu <James.Zhu@amd.com> Acked-by: Christian König <christian.koenig@amd.com> Link: https://patchwork.freedesktop.org/patch/msgid/20240823163048.2676257-2-michal.winiarski@intel.com Signed-off-by: Christian König <christian.koenig@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
xattr in ocfs2 maybe 'non-indexed', which saved with additional space
requested. It's better to check if the memory is out of bound before
memcmp, although this possibility mainly comes from crafted poisonous
images.
Link: https://lkml.kernel.org/r/20240520024024.1976129-2-joseph.qi@linux.alibaba.com Signed-off-by: Ferry Meng <mengferry@linux.alibaba.com> Signed-off-by: Joseph Qi <joseph.qi@linux.alibaba.com> Reported-by: lei lu <llfamsec@gmail.com> Reviewed-by: Joseph Qi <joseph.qi@linux.alibaba.com> Cc: Changwei Ge <gechangwei@live.cn> Cc: Gang He <ghe@suse.com> Cc: Joel Becker <jlbec@evilplan.org> Cc: Jun Piao <piaojun@huawei.com> Cc: Junxiao Bi <junxiao.bi@oracle.com> Cc: Mark Fasheh <mark@fasheh.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Add a paranoia check to make sure it doesn't stray beyond valid memory
region containing ocfs2 xattr entries when scanning for a match. It will
prevent out-of-bound access in case of crafted images.
Link: https://lkml.kernel.org/r/20240520024024.1976129-1-joseph.qi@linux.alibaba.com Signed-off-by: Ferry Meng <mengferry@linux.alibaba.com> Signed-off-by: Joseph Qi <joseph.qi@linux.alibaba.com> Reported-by: lei lu <llfamsec@gmail.com> Reviewed-by: Joseph Qi <joseph.qi@linux.alibaba.com> Cc: Mark Fasheh <mark@fasheh.com> Cc: Joel Becker <jlbec@evilplan.org> Cc: Junxiao Bi <junxiao.bi@oracle.com> Cc: Changwei Ge <gechangwei@live.cn> Cc: Gang He <ghe@suse.com> Cc: Jun Piao <piaojun@huawei.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Stable-dep-of: af77c4fc1871 ("ocfs2: strict bound check before memcmp in ocfs2_xattr_find_entry()") Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit 82b74cac2849 ("blk-ioprio: Convert from rqos policy to direct
call") pushed setting bio I/O priority down into blk_mq_submit_bio()
-- which is too low within block core's submit_bio() because it
skips setting I/O priority for block drivers that implement
fops->submit_bio() (e.g. DM, MD, etc).
Fix this by moving bio_set_ioprio() up from blk-mq.c to blk-core.c and
call it from submit_bio(). This ensures all block drivers call
bio_set_ioprio() during initial bio submission.
Fixes: a78418e6a04c ("block: Always initialize bio IO priority on submit") Co-developed-by: Yibin Ding <yibin.ding@unisoc.com> Signed-off-by: Yibin Ding <yibin.ding@unisoc.com> Signed-off-by: Hongyu Jin <hongyu.jin@unisoc.com> Reviewed-by: Eric Biggers <ebiggers@google.com> Reviewed-by: Mikulas Patocka <mpatocka@redhat.com>
[snitzer: revised commit header] Signed-off-by: Mike Snitzer <snitzer@kernel.org> Reviewed-by: Ming Lei <ming.lei@redhat.com> Link: https://lore.kernel.org/r/20240130202638.62600-2-snitzer@kernel.org Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
A Linux guest on Hyper-V gets the TSC frequency from a synthetic MSR, if
available. In this case, set X86_FEATURE_TSC_KNOWN_FREQ so that Linux
doesn't unnecessarily do refined TSC calibration when setting up the TSC
clocksource.
With this change, a message such as this is no longer output during boot
when the TSC is used as the clocksource:
Furthermore, the guest and host will have exactly the same view of the
TSC frequency, which is important for features such as the TSC deadline
timer that are emulated by the Hyper-V host.
Signed-off-by: Michael Kelley <mhklinux@outlook.com> Reviewed-by: Roman Kisel <romank@linux.microsoft.com> Link: https://lore.kernel.org/r/20240606025559.1631-1-mhklinux@outlook.com Signed-off-by: Wei Liu <wei.liu@kernel.org>
Message-ID: <20240606025559.1631-1-mhklinux@outlook.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Call cifs_reconnect() to wake up processes waiting on negotiate
protocol to handle the case where server abruptly shut down and had no
chance to properly close the socket.
We use komeda_crtc_normalize_zpos to normalize zpos of affected planes
to their blending zorder in CU. If there's only one slave plane in
affected planes and its layer_split property is enabled, order++ for
its split layer, so that when calculating the normalized_zpos
of master planes, the split layer of the slave plane is included, but
the max_slave_zorder does not include the split layer and keep zero
because there's only one slave plane in affacted planes, although we
actually use two slave layers in this commit.
In most cases, this bug does not result in a commit failure, but assume
the following situation:
slave_layer 0: zpos = 0, layer split enabled, normalized_zpos =
0;(use slave_layer 2 as its split layer)
master_layer 0: zpos = 2, layer_split enabled, normalized_zpos =
2;(use master_layer 2 as its split layer)
master_layer 1: zpos = 4, normalized_zpos = 4;
master_layer 3: zpos = 5, normalized_zpos = 5;
kcrtc_st->max_slave_zorder = 0;
When we use master_layer 3 as a input of CU in function
komeda_compiz_set_input and check it with function
komeda_component_check_input, the parameter idx is equal to
normailzed_zpos minus max_slave_zorder, the value of idx is 5
and is euqal to CU's max_active_inputs, so that
komeda_component_check_input returns a -EINVAL value.
To fix the bug described above, when calculating the max_slave_zorder
with the layer_split enabled, count the split layer in this calculation
directly.
There are 2G and 4G RAM versions of the Lenovo Yoga Tab 3 X90F and it
turns out that the 2G version has a DMI product name of
"CHERRYVIEW D1 PLATFORM" where as the 4G version has
"CHERRYVIEW C0 PLATFORM". The sys-vendor + product-version check are
unique enough that the product-name check is not necessary.
Drop the product-name check so that the existing DMI match for the 4G
RAM version also matches the 2G RAM version.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Link: https://patch.msgid.link/20240823074305.16873-1-hdegoede@redhat.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When changing the interface from CAN-CC to CAN-FD mode the old
coalescing parameters are re-used. This might cause problem, as the
configured parameters are too big for CAN-FD mode.
During testing an invalid TX coalescing configuration has been seen.
The problem should be been fixed in the previous patch, but add a
safeguard here to ensure that the number of TEF coalescing buffers (if
configured) is exactly the half of all TEF buffers.
When the firmware crashes, we first told the op_mode and only then,
changed the transport's state. This is a problem if the op_mode's
nic_error() handler needs to send a host command: it'll see that the
transport's state still reflects that the firmware is alive.
Today, this has no consequences since we set the STATUS_FW_ERROR bit and
that will prevent sending host commands. iwl_fw_dbg_stop_restart_recording
looks at this bit to know not to send a host command for example.
To fix the hibernation, we needed to reset the firmware without having
an error and checking STATUS_FW_ERROR to see whether the firmware is
alive will no longer hold, so this change is necessary as well.
Change the flow a bit.
Change trans->state before calling the op_mode's nic_error() method and
check trans->state instead of STATUS_FW_ERROR. This will keep the
current behavior of iwl_fw_dbg_stop_restart_recording upon firmware
error, and it'll allow us to call iwl_fw_dbg_stop_restart_recording
safely even if STATUS_FW_ERROR is clear, but yet, the firmware is not
alive.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com> Link: https://patch.msgid.link/20240825191257.9d7427fbdfd7.Ia056ca57029a382c921d6f7b6a6b28fc480f2f22@changeid
[I missed this was a dependency for the hibernation fix, changed
the commit message a bit accordingly] Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
There is a WARNING in iwl_trans_wait_tx_queues_empty() (that was
recently converted from just a message), that can be hit if we
wait for TX queues to become empty after firmware died. Clearly,
we can't expect anything from the firmware after it's declared dead.
Don't call iwl_trans_wait_tx_queues_empty() in this case. While it could
be a good idea to stop the flow earlier, the flush functions do some
maintenance work that is not related to the firmware, so keep that part
of the code running even when the firmware is not running.
The calculation should consider also the 6GHz IE's len, fix that.
In addition, in iwl_mvm_sched_scan_start() the scan_fits helper is
called only in case non_psc_incldued is true, but it should be called
regardless, fix that as well.
An invalid buffer destination is not a problem for the driver and it
does not make sense to report it with the KERN_ERR message level. As
such, change the message to use IWL_DEBUG_FW.
Reported-by: Len Brown <lenb@kernel.org> Closes: https://lore.kernel.org/r/CAJvTdKkcxJss=DM2sxgv_MR5BeZ4_OC-3ad6tA40TYH2yqHCWw@mail.gmail.com Signed-off-by: Benjamin Berg <benjamin.berg@intel.com> Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com> Link: https://patch.msgid.link/20240825191257.20abf78f05bc.Ifbcecc2ae9fb40b9698302507dcba8b922c8d856@changeid Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently we call irq_set_noprobe() in a loop for all IRQs, but indeed
it only works for IRQs below NR_IRQS_LEGACY because at init_IRQ() only
legacy interrupts have been allocated.
Instead, we can define ARCH_IRQ_INIT_FLAGS as IRQ_NOPROBE in asm/hwirq.h
and the core will automatically set the flag for all interrupts.
The driver must ensure TX descriptor updates are visible
before updating TX pointer and TX clear pointer.
This resolves TX hangs observed on AST2600 when running
iperf3.
Signed-off-by: Jacky Chou <jacky_chou@aspeedtech.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
There are 2G and 4G RAM versions of the Lenovo Yoga Tab 3 X90F and it
turns out that the 2G version has a DMI product name of
"CHERRYVIEW D1 PLATFORM" where as the 4G version has
"CHERRYVIEW C0 PLATFORM". The sys-vendor + product-version check are
unique enough that the product-name check is not necessary.
Drop the product-name check so that the existing DMI match for the 4G
RAM version also matches the 2G RAM version.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Link: https://lore.kernel.org/r/20240825132415.8307-1-hdegoede@redhat.com Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Before commit 721f4a6526da ("mm/memblock: remove empty dummy entry") the
check for non-zero of memblock.reserved.cnt in mmu_init() would always
be true either because memblock.reserved.cnt is initialized to 1 or
because there were memory reservations earlier.
The removal of dummy empty entry in memblock caused this check to fail
because now memblock.reserved.cnt is initialized to 0.
Remove the check for non-zero of memblock.reserved.cnt because it's
perfectly fine to have an empty memblock.reserved array that early in
boot.
pinctrl-at91 currently does not support the gpio-groups devicetree
property and has no pin-range.
Because of this at91 gpios stopped working since patch
commit 2ab73c6d8323fa1e ("gpio: Support GPIO controllers without pin-ranges")
This was discussed in the patches
commit fc328a7d1fcce263 ("gpio: Revert regression in sysfs-gpio (gpiolib.c)")
commit 56e337f2cf132632 ("Revert "gpio: Revert regression in sysfs-gpio (gpiolib.c)"")
As a workaround manually set pin-range via gpiochip_add_pin_range() until
a) pinctrl-at91 is reworked to support devicetree gpio-groups
b) another solution as mentioned in
commit 56e337f2cf132632 ("Revert "gpio: Revert regression in sysfs-gpio (gpiolib.c)"")
is found
Dell platform with ALC215 ALC285 ALC289 ALC225 ALC295 ALC299, plug
headphone or headset.
It had a chance to get no sound from headphone.
Replace depop procedure will solve this issue.
Add AFE Control Register 0 to the volatile_register.
AFE_DAC_CON0 can be modified by both the SOF and ALSA drivers.
If this register is read and written in cache mode, the cached value
might not reflect the actual value when the register is modified by
another driver. It can cause playback or capture failures. Therefore,
it is necessary to add AFE_DAC_CON0 to the list of volatile registers.
Signed-off-by: YR Yang <yr.yang@mediatek.com> Reviewed-by: Fei Shao <fshao@chromium.org> Reviewed-by: Trevor Wu <trevor.wu@mediatek.com> Link: https://patch.msgid.link/20240801084326.1472-1-yr.yang@mediatek.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Buffer 'card->dai_link' is reallocated in 'meson_card_reallocate_links()',
so move 'pad' pointer initialization after this function when memory is
already reallocated.
Kasan bug report:
==================================================================
BUG: KASAN: slab-use-after-free in axg_card_add_link+0x76c/0x9bc
Read of size 8 at addr ffff000000e8b260 by task modprobe/356
Intel Arrow Lake-H/U has the same GPIO hardware than Meteor Lake-P but
the ACPI ID is different. Add this new ACPI ID to the list of supported
devices.
Cc: stable@vger.kernel.org Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the calculation of packet signatures by adding the offset into a page
in the read or write data payload when hashing the pages from it.
Fixes: 39bc58203f04 ("cifs: Add a function to Hash the contents of an iterator") Signed-off-by: David Howells <dhowells@redhat.com> Reviewed-by: Tom Talpey <tom@talpey.com> Reviewed-by: Paulo Alcantara (Red Hat) <pc@manguebit.com>
cc: Shyam Prasad N <nspmangalore@gmail.com>
cc: Rohith Surabattula <rohiths.msft@gmail.com>
cc: Jeff Layton <jlayton@kernel.org>
cc: linux-cifs@vger.kernel.org
cc: linux-fsdevel@vger.kernel.org Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Clang static checker (scan-build) warning:
sound/soc/codecs/peb2466.c:232:8:
Assigned value is garbage or undefined [core.uninitialized.Assign]
232 | *val = tmp;
| ^ ~~~
When peb2466_read_byte() fails, 'tmp' will have a garbage value.
Add a judgemnet to avoid this problem.
Fixes: 227f609c7c0e ("ASoC: codecs: Add support for the Infineon PEB2466 codec") Signed-off-by: Su Hui <suhui@nfschina.com> Link: https://patch.msgid.link/20240911115448.277828-1-suhui@nfschina.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
It may be possible for the sum of the values derived from
i915_ggtt_offset() and __get_parent_scratch_offset()/
i915_ggtt_offset() to go over the u32 limit before being assigned
to wq offsets of u64 type.
Mitigate these issues by expanding one of the right operands
to u64 to avoid any overflow issues just in case.
Found by Linux Verification Center (linuxtesting.org) with static
analysis tool SVACE.
In spi_geni_remove(), the free_irq() sequence is different from that
on the probe error path. And the IRQ will still remain and it's interrupt
handler may use the dma channel after release dma channel and before free
irq, which is not secure, fix it.
Fixes: b59c122484ec ("spi: spi-geni-qcom: Add support for GPI dma") Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com> Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Link: https://patch.msgid.link/20240909073141.951494-3-ruanjinjie@huawei.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
It's important to undo pm_runtime_use_autosuspend() with
pm_runtime_dont_use_autosuspend() at driver exit time unless driver
initially enabled pm_runtime with devm_pm_runtime_enable()
(which handles it for you).
Hence, switch to devm_pm_runtime_enable() to fix it, so the
pm_runtime_disable() in probe error path and remove function
can be removed.
Fixes: cfdab2cd85ec ("spi: spi-geni-qcom: Set an autosuspend delay of 250 ms") Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com> Suggested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Link: https://patch.msgid.link/20240909073141.951494-2-ruanjinjie@huawei.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
init() was removed from ramgp102 when reworking the memory detection, as
it was thought that the code was only necessary when the driver performs
mclk changes, which nouveau doesn't support on pascal.
However, it turns out that we still need to execute this on some GPUs to
restore settings after DEVINIT, so revert to the original behaviour.
Until VM_DONTEXPAND was added in commit 1c1914d6e8c6 ("dma-buf: heaps:
Don't track CMA dma-buf pages under RssFile") it was possible to obtain
a mapping larger than the buffer size via mremap and bypass the overflow
check in dma_buf_mmap_internal. When using such a mapping to attempt to
fault past the end of the buffer, the CMA heap fault handler also checks
the fault offset against the buffer size, but gets the boundary wrong by
1. Fix the boundary check so that we don't read off the end of the pages
array and insert an arbitrary page in the mapping.
Reported-by: Xingyu Jin <xingyuj@google.com> Fixes: a5d2d29e24be ("dma-buf: heaps: Move heap-helper logic into the cma_heap implementation") Cc: stable@vger.kernel.org # Applicable >= 5.10. Needs adjustments only for 5.10. Signed-off-by: T.J. Mercier <tjmercier@google.com> Acked-by: John Stultz <jstultz@google.com> Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org> Link: https://patchwork.freedesktop.org/patch/msgid/20240830192627.2546033-1-tjmercier@google.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A syncobj reference is taken in drm_syncobj_find, but not released if
eventfd_ctx_fdget or kzalloc fails. Put the reference in these error
paths.
Reported-by: Xingyu Jin <xingyuj@google.com> Fixes: c7a472297169 ("drm/syncobj: add IOCTL to register an eventfd") Signed-off-by: T.J. Mercier <tjmercier@google.com> Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@igalia.com>
Reviewed-by. Christian König <christian.koenig@amd.com> CC: stable@vger.kernel.org # 6.6+ Link: https://patchwork.freedesktop.org/patch/msgid/20240909205400.3498337-1-tjmercier@google.com Signed-off-by: Christian König <christian.koenig@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit ab8d66d132bc8f1992d3eb6cab8d32dda6733c84 because it
breaks codecs using non-continuous masks in source and sink ports. The
commit missed the point that port numbers are not used as indices for
iterating over prop.sink_ports or prop.source_ports.
Soundwire core and existing codecs expect that the array passed as
prop.sink_ports and prop.source_ports is continuous. The port mask still
might be non-continuous, but that's unrelated.
Reported-by: Bard Liao <yung-chuan.liao@linux.intel.com> Closes: https://lore.kernel.org/all/b6c75eee-761d-44c8-8413-2a5b34ee2f98@linux.intel.com/ Fixes: ab8d66d132bc ("soundwire: stream: fix programming slave ports for non-continous port maps") Acked-by: Bard Liao <yung-chuan.liao@linux.intel.com> Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com> Cc: stable@vger.kernel.org Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Tested-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com> Link: https://lore.kernel.org/r/20240909164746.136629-1-krzysztof.kozlowski@linaro.org Signed-off-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Change the memcpy length to fix the out-of-bounds issue when writing the
data that is not 4 byte aligned to TX FIFO.
To reproduce the issue, write 3 bytes data to NOR chip.
dd if=3b of=/dev/mtd0
[ 36.926103] ==================================================================
[ 36.933409] BUG: KASAN: slab-out-of-bounds in nxp_fspi_exec_op+0x26ec/0x2838
[ 36.940514] Read of size 4 at addr ffff00081037c2a0 by task dd/455
[ 36.946721]
[ 36.948235] CPU: 3 UID: 0 PID: 455 Comm: dd Not tainted 6.11.0-rc5-gc7b0e37c8434 #1070
[ 36.956185] Hardware name: Freescale i.MX8QM MEK (DT)
[ 36.961260] Call trace:
[ 36.963723] dump_backtrace+0x90/0xe8
[ 36.967414] show_stack+0x18/0x24
[ 36.970749] dump_stack_lvl+0x78/0x90
[ 36.974451] print_report+0x114/0x5cc
[ 36.978151] kasan_report+0xa4/0xf0
[ 36.981670] __asan_report_load_n_noabort+0x1c/0x28
[ 36.986587] nxp_fspi_exec_op+0x26ec/0x2838
[ 36.990800] spi_mem_exec_op+0x8ec/0xd30
[ 36.994762] spi_mem_no_dirmap_read+0x190/0x1e0
[ 36.999323] spi_mem_dirmap_write+0x238/0x32c
[ 37.003710] spi_nor_write_data+0x220/0x374
[ 37.007932] spi_nor_write+0x110/0x2e8
[ 37.011711] mtd_write_oob_std+0x154/0x1f0
[ 37.015838] mtd_write_oob+0x104/0x1d0
[ 37.019617] mtd_write+0xb8/0x12c
[ 37.022953] mtdchar_write+0x224/0x47c
[ 37.026732] vfs_write+0x1e4/0x8c8
[ 37.030163] ksys_write+0xec/0x1d0
[ 37.033586] __arm64_sys_write+0x6c/0x9c
[ 37.037539] invoke_syscall+0x6c/0x258
[ 37.041327] el0_svc_common.constprop.0+0x160/0x22c
[ 37.046244] do_el0_svc+0x44/0x5c
[ 37.049589] el0_svc+0x38/0x78
[ 37.052681] el0t_64_sync_handler+0x13c/0x158
[ 37.057077] el0t_64_sync+0x190/0x194
[ 37.060775]
[ 37.062274] Allocated by task 455:
[ 37.065701] kasan_save_stack+0x2c/0x54
[ 37.069570] kasan_save_track+0x20/0x3c
[ 37.073438] kasan_save_alloc_info+0x40/0x54
[ 37.077736] __kasan_kmalloc+0xa0/0xb8
[ 37.081515] __kmalloc_noprof+0x158/0x2f8
[ 37.085563] mtd_kmalloc_up_to+0x120/0x154
[ 37.089690] mtdchar_write+0x130/0x47c
[ 37.093469] vfs_write+0x1e4/0x8c8
[ 37.096901] ksys_write+0xec/0x1d0
[ 37.100332] __arm64_sys_write+0x6c/0x9c
[ 37.104287] invoke_syscall+0x6c/0x258
[ 37.108064] el0_svc_common.constprop.0+0x160/0x22c
[ 37.112972] do_el0_svc+0x44/0x5c
[ 37.116319] el0_svc+0x38/0x78
[ 37.119401] el0t_64_sync_handler+0x13c/0x158
[ 37.123788] el0t_64_sync+0x190/0x194
[ 37.127474]
[ 37.128977] The buggy address belongs to the object at ffff00081037c2a0
[ 37.128977] which belongs to the cache kmalloc-8 of size 8
[ 37.141177] The buggy address is located 0 bytes inside of
[ 37.141177] allocated 3-byte region [ffff00081037c2a0, ffff00081037c2a3)
[ 37.153465]
[ 37.154971] The buggy address belongs to the physical page:
[ 37.160559] page: refcount:1 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x89037c
[ 37.168596] flags: 0xbfffe0000000000(node=0|zone=2|lastcpupid=0x1ffff)
[ 37.175149] page_type: 0xfdffffff(slab)
[ 37.179021] raw: 0bfffe0000000000ffff000800002500dead0000000001220000000000000000
[ 37.186788] raw: 0000000000000000000000008080008000000001fdffffff0000000000000000
[ 37.194553] page dumped because: kasan: bad access detected
[ 37.200144]
[ 37.201647] Memory state around the buggy address:
[ 37.206460] ffff00081037c180: fa fc fc fc fa fc fc fc fa fc fc fc fa fc fc fc
[ 37.213701] ffff00081037c200: fa fc fc fc 05 fc fc fc 03 fc fc fc 02 fc fc fc
[ 37.220946] >ffff00081037c280: 06 fc fc fc 03 fc fc fc fc fc fc fc fc fc fc fc
[ 37.228186] ^
[ 37.232473] ffff00081037c300: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 37.239718] ffff00081037c380: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 37.246962] ==================================================================
[ 37.254394] Disabling lock debugging due to kernel taint
0+1 records in
0+1 records out
3 bytes copied, 0.335911 s, 0.0 kB/s
Fixes: a5356aef6a90 ("spi: spi-mem: Add driver for NXP FlexSPI controller") Cc: stable@kernel.org Signed-off-by: Han Xu <han.xu@nxp.com> Link: https://patch.msgid.link/20240911211146.3337068-1-han.xu@nxp.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To fix some critical section races, the interface_lock was added to a few
locations. One of those locations was above where the interface_lock was
declared, so the declaration was moved up before that usage.
Unfortunately, where it was placed was inside a CONFIG_TIMERLAT_TRACER
ifdef block. As the interface_lock is used outside that config, this broke
the build when CONFIG_OSNOISE_TRACER was enabled but
CONFIG_TIMERLAT_TRACER was not.
Cc: Masami Hiramatsu <mhiramat@kernel.org> Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com> Cc: "Helena Anna" <helena.anna.dubel@intel.com> Cc: "Luis Claudio R. Goncalves" <lgoncalv@redhat.com> Cc: Tomas Glozar <tglozar@redhat.com> Link: https://lore.kernel.org/20240909103231.23a289e2@gandalf.local.home Fixes: e6a53481da29 ("tracing/timerlat: Only clear timer if a kthread exists") Reported-by: "Bityutskiy, Artem" <artem.bityutskiy@intel.com> Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When sending packets under 60 bytes, up to three bytes of the buffer
following the data may be leaked. Avoid this by extending all packets to
ETH_ZLEN, ensuring nothing is leaked in the padding. This bug can be
reproduced by running
$ ping -s 11 destination
Fixes: 9ad1a3749333 ("dpaa_eth: add support for DPAA Ethernet") Suggested-by: Eric Dumazet <edumazet@google.com> Signed-off-by: Sean Anderson <sean.anderson@linux.dev> Reviewed-by: Eric Dumazet <edumazet@google.com> Link: https://patch.msgid.link/20240910143144.1439910-1-sean.anderson@linux.dev Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The TAS module could not be configured when it's running in pending
status. We need disable the module and configure it again. However, the
pending status is not cleared after the module disabled. TC taprio set
will always return busy even it's disabled.
For example, a user uses tc-taprio to configure Qbv and a future
basetime. The TAS module will run in a pending status. There is no way
to reconfigure Qbv, it always returns busy.
Actually the TAS module can be reconfigured when it's disabled. So it
doesn't need to check the pending status if the TAS module is disabled.
After the patch, user can delete the tc taprio configuration to disable
Qbv and reconfigure it again.
Fixes: de143c0e274b ("net: dsa: felix: Configure Time-Aware Scheduler via taprio offload") Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com> Link: https://patch.msgid.link/20240906093550.29985-1-xiaoliang.yang_1@nxp.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Padding is not included in UDP and TCP checksums. Therefore, reduce the
length of the checksummed data to include only the data in the IP
payload. This fixes spurious reported checksum failures like
rx: pkt: sport=33000 len=26 csum=0xc850 verify=0xf9fe
pkt: bad csum
Technically it is possible for there to be trailing bytes after the UDP
data but before the Ethernet padding (e.g. if sizeof(ip) + sizeof(udp) +
udp.len < ip.len). However, we don't generate such packets.
Fixes: 91a7de85600d ("selftests/net: add csum offload test") Signed-off-by: Sean Anderson <sean.anderson@linux.dev> Reviewed-by: Willem de Bruijn <willemb@google.com> Link: https://patch.msgid.link/20240906210743.627413-1-sean.anderson@linux.dev Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently, the driver only enables RX interrupt to handle RX
packets and TX resources. Sometimes there is not RX traffic,
so the TX resource needs to wait for RX interrupt to free.
This situation will toggle the TX timeout watchdog when the MAC
TX ring has no more resources to transmit packets.
Therefore, enable TX interrupt to release TX resources at any time.
When I am verifying iperf3 over UDP, the network hangs.
Like the log below.
The network topology is FTGMAC connects directly to a PC.
UDP does not need to wait for ACK, unlike TCP.
Therefore, FTGMAC needs to enable TX interrupt to release TX resources instead
of waiting for the RX interrupt.
The current implementation of SMQ flush sequence waits for the packets
in the TM pipeline to be transmitted out of the link. This sequence
doesn't succeed in HW when there is any issue with link such as lack of
link credits, link down or any other traffic that is fully occupying the
link bandwidth (QoS). This patch modifies the SMQ flush sequence to
drop the packets after TL1 level (SQM) instead of polling for the packets
to be sent out of RPM/CGX link.
The bridge mode is only relevant when there are multiple functions per
port. Therefore, prevent setting and getting this setting when there are no
VFs.
Note that after this change, there are no settings to change on the PF
interface using `bridge link` when there are no VFs, so the interface no
longer appears in the `bridge link` output.
Fixes: 4b89251de024 ("net/mlx5: Support ndo bridge_setlink and getlink") Signed-off-by: Benjamin Poirier <bpoirier@nvidia.com> Reviewed-by: Cosmin Ratiu <cratiu@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Before creating a scheduling element in a NIC or E-Switch scheduler,
ensure that the requested element type is supported. If the element is
of type Transmit Scheduling Arbiter (TSAR), also verify that the
specific TSAR type is supported.
Always call igb_xdp_ring_update_tail() under __netif_tx_lock, add a comment
and lockdep assert to indicate that. This is needed to share the same TX
ring between XDP, XSK and slow paths. Furthermore, the current XDP
implementation is racy on tail updates.
Fixes: 9cbc948b5a20 ("igb: add XDP support") Signed-off-by: Sriram Yagnaraman <sriram.yagnaraman@est.tech>
[Kurt: Add lockdep assert and fixes tag] Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de> Acked-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com> Tested-by: George Kuruvinakunnel <george.kuruvinakunnel@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The description of function ice_find_vsi_list_entry says:
Search VSI list map with VSI count 1
However, since the blamed commit (see Fixes below), the function no
longer checks vsi_count. This causes a problem in ice_add_vlan_internal,
where the decision to share VSI lists between filter rules relies on the
vsi_count of the found existing VSI list being 1.
The reproducing steps:
1. Have a PF and two VFs.
There will be a filter rule for VLAN 0, referring to a VSI list
containing VSIs: 0 (PF), 2 (VF#0), 3 (VF#1).
2. Add VLAN 1234 to VF#0.
ice will make the wrong decision to share the VSI list with the new
rule. The wrong behavior may not be immediately apparent, but it can
be observed with debug prints.
3. Add VLAN 1234 to VF#1.
ice will unshare the VSI list for the VLAN 1234 rule. Due to the
earlier bad decision, the newly created VSI list will contain
VSIs 0 (PF) and 3 (VF#1), instead of expected 2 (VF#0) and 3 (VF#1).
4. Try pinging a network peer over the VLAN interface on VF#0.
This fails.
Reproducer script at:
https://gitlab.com/mschmidt2/repro/-/blob/master/RHEL-46814/test-vlan-vsi-list-confusion.sh
Commented debug trace:
https://gitlab.com/mschmidt2/repro/-/blob/master/RHEL-46814/ice-vlan-vsi-lists-debug.txt
Patch adding the debug prints:
https://gitlab.com/mschmidt2/linux/-/commit/f8a8814623944a45091a77c6094c40bfe726bfdb
(Unsafe, by the way. Lacks rule_lock when dumping in ice_remove_vlan.)
Michal Swiatkowski added to the explanation that the bug is caused by
reusing a VSI list created for VLAN 0. All created VFs' VSIs are added
to VLAN 0 filter. When a non-zero VLAN is created on a VF which is already
in VLAN 0 (normal case), the VSI list from VLAN 0 is reused.
It leads to a problem because all VFs (VSIs to be specific) that are
subscribed to VLAN 0 will now receive a new VLAN tag traffic. This is
one bug, another is the bug described above. Removing filters from
one VF will remove VLAN filter from the previous VF. It happens a VF is
reset. Example:
- creation of 3 VFs
- we have VSI list (used for VLAN 0) [0 (pf), 2 (vf1), 3 (vf2), 4 (vf3)]
- we are adding VLAN 100 on VF1, we are reusing the previous list
because 2 is there
- VLAN traffic works fine, but VLAN 100 tagged traffic can be received
on all VSIs from the list (for example broadcast or unicast)
- trust is turning on VF2, VF2 is resetting, all filters from VF2 are
removed; the VLAN 100 filter is also removed because 3 is on the list
- VLAN traffic to VF1 isn't working anymore, there is a need to recreate
VLAN interface to readd VLAN filter
One thing I'm not certain about is the implications for the LAG feature,
which is another caller of ice_find_vsi_list_entry. I don't have a
LAG-capable card at hand to test.
Fixes: 23ccae5ce15f ("ice: changes to the interface with the HW and FW for SRIOV_VF+LAG") Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com> Signed-off-by: Michal Schmidt <mschmidt@redhat.com> Reviewed-by: Dave Ertman <David.m.ertman@intel.com> Tested-by: Rafal Romanowski <rafal.romanowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When adding a switch filter (such as a MAC or VLAN filter), it is expected
that the driver will detect the case where the filter already exists, and
return -EEXIST. This is used by calling code such as ice_vc_add_mac_addr,
and ice_vsi_add_vlan to avoid incrementing the accounting fields such as
vsi->num_vlan or vf->num_mac.
This logic works correctly for the case where only a single VSI has added a
given switch filter.
When a second VSI adds the same switch filter, the driver converts the
existing filter from an ICE_FWD_TO_VSI filter into an ICE_FWD_TO_VSI_LIST
filter. This saves switch resources, by ensuring that multiple VSIs can
re-use the same filter.
The ice_add_update_vsi_list() function is responsible for doing this
conversion. When first converting a filter from the FWD_TO_VSI into
FWD_TO_VSI_LIST, it checks if the VSI being added is the same as the
existing rule's VSI. In such a case it returns -EEXIST.
However, when the switch rule has already been converted to a
FWD_TO_VSI_LIST, the logic is different. Adding a new VSI in this case just
requires extending the VSI list entry. The logic for checking if the rule
already exists in this case returns 0 instead of -EEXIST.
This breaks the accounting logic mentioned above, so the counters for how
many MAC and VLAN filters exist for a given VF or VSI no longer accurately
reflect the actual count. This breaks other code which relies on these
counts.
In typical usage this primarily affects such filters generally shared by
multiple VSIs such as VLAN 0, or broadcast and multicast MAC addresses.
Fix this by correctly reporting -EEXIST in the case of adding the same VSI
to a switch rule already converted to ICE_FWD_TO_VSI_LIST.
Fixes: 9daf8208dd4d ("ice: Add support for switch filter programming") Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Rafal Romanowski <rafal.romanowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / thirdparty / kernel / stable.git / log
