After commit 13a4b7fb6260 ("pmdomain: core: Leave powered-on genpds on
until late_initcall_sync") was applied, the Tegra210 Jetson TX1 board
failed to boot. Looking into this issue, before this commit was applied,
if any of the Tegra power-domains were in 'on' state when the kernel
booted, they were being turned off by the genpd core before any driver
had chance to request them. This was purely by luck and a consequence of
the power-domains being turned off earlier during boot. After this
commit was applied, any power-domains in the 'on' state are kept on for
longer during boot and therefore, may never transitioned to the off
state before they are requested/used. The hang on the Tegra210 Jetson
TX1 is caused because devices in some power-domains are accessed without
the power-domain being turned off and on, indicating that the
power-domain is not in a completely on state.
>From reviewing the Tegra PMC driver code, if a power-domain is in the
'on' state there is no guarantee that all the necessary clocks
associated with the power-domain are on and even if they are they would
not have been requested via the clock framework and so could be turned
off later. Some power-domains also have a 'clamping' register that needs
to be configured as well. In short, if a power-domain is already 'on' it
is difficult to know if it has been configured correctly. Given that the
power-domains happened to be switched off during boot previously, to
ensure that they are in a good known state on boot, fix this by
switching off any power-domains that are on initially when registering
the power-domains with the genpd framework.
Note that commit 05cfb988a4d0 ("soc/tegra: pmc: Initialise resets
associated with a power partition") updated the
tegra_powergate_of_get_resets() function to pass the 'off' to ensure
that the resets for the power-domain are in the correct state on boot.
However, now that we may power off a domain on boot, if it is on, it is
better to move this logic into the tegra_powergate_add() function so
that there is a single place where we are handling the initial state of
the power-domain.
Both jbd2_log_do_checkpoint() and jbd2_journal_shrink_checkpoint_list()
periodically release j_list_lock after processing a batch of buffers to
avoid long hold times on the j_list_lock. However, since both functions
contend for j_list_lock, the combined time spent waiting and processing
can be significant.
jbd2_journal_shrink_checkpoint_list() explicitly calls cond_resched() when
need_resched() is true to avoid softlockups during prolonged operations.
But jbd2_log_do_checkpoint() only exits its loop when need_resched() is
true, relying on potentially sleeping functions like __flush_batch() or
wait_on_buffer() to trigger rescheduling. If those functions do not sleep,
the kernel may hit a softlockup.
An endpoint driver configfs attributes group is added to the
epf_group list of struct pci_epf_driver by pci_epf_add_cfs() but an
added group is not removed from this list when the attribute group is
unregistered with pci_ep_cfs_remove_epf_group().
Add the missing list_del() call in pci_ep_cfs_remove_epf_group()
to correctly remove the attribute group from the driver list.
With this change, once the loop over all attribute groups in
pci_epf_remove_cfs() completes, the driver epf_group list should be
empty. Add a WARN_ON() to make sure of that.
Fixes: ef1433f717a2 ("PCI: endpoint: Create configfs entry for each pci_epf_device_id table entry") Signed-off-by: Damien Le Moal <dlemoal@kernel.org> Signed-off-by: Manivannan Sadhasivam <mani@kernel.org> Reviewed-by: Niklas Cassel <cassel@kernel.org> Cc: stable@vger.kernel.org Link: https://patch.msgid.link/20250624114544.342159-3-dlemoal@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Doing a list_del() on the epf_group field of struct pci_epf_driver in
pci_epf_remove_cfs() is not correct as this field is a list head, not
a list entry. This list_del() call triggers a KASAN warning when an
endpoint function driver which has a configfs attribute group is torn
down:
==================================================================
BUG: KASAN: slab-use-after-free in pci_epf_remove_cfs+0x17c/0x198
Write of size 8 at addr ffff00010f4a0d80 by task rmmod/319
The Linux hwmon sysfs API values for pwmX_auto_pointY_pwm represent an
integer value between 0 (0%) to 255 (100%) and the pwmX_auto_pointY_temp
represent millidegrees Celcius.
Commit a6d80df47ee2 ("hwmon: (gsc-hwmon) fix fan pwm temperature
scaling") properly addressed the incorrect scaling in the
pwm_auto_point_temp_store implementation but erroneously scaled
the pwm_auto_point_pwm_show (pwm value) instead of the
pwm_auto_point_temp_show (temp value) resulting in:
# cat /sys/class/hwmon/hwmon0/pwm1_auto_point6_pwm
25500
# cat /sys/class/hwmon/hwmon0/pwm1_auto_point6_temp
4500
Fix the scaling of these attributes:
# cat /sys/class/hwmon/hwmon0/pwm1_auto_point6_pwm
255
# cat /sys/class/hwmon/hwmon0/pwm1_auto_point6_temp
45000
Fixes: a6d80df47ee2 ("hwmon: (gsc-hwmon) fix fan pwm temperature scaling") Cc: stable@vger.kernel.org Signed-off-by: Tim Harvey <tharvey@gateworks.com> Link: https://lore.kernel.org/r/20250718200259.1840792-1-tharvey@gateworks.com Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As per the i.MX93 TRM, section 67.3.2.1 "MOD register update", the value
of the TPM counter does NOT get updated when writing MOD.MOD unless
SC.CMOD != 0. Therefore, with the current code, assuming the following
sequence:
1) pwm_disable()
2) pwm_apply_might_sleep() /* period is changed here */
3) pwm_enable()
and assuming only one channel is active, if CNT.COUNT is higher than the
MOD.MOD value written during the pwm_apply_might_sleep() call then, when
re-enabling the PWM during pwm_enable(), the counter will end up resetting
after UINT32_MAX - CNT.COUNT + MOD.MOD cycles instead of MOD.MOD cycles as
normally expected.
Fix this problem by forcing a reset of the TPM counter before MOD.MOD is
written.
Add the missing memory barrier to make sure that LMAC source ring
descriptors are written before updating the head pointer to avoid
passing stale data to the firmware on weakly ordered architectures like
aarch64.
Note that non-LMAC rings use MMIO write accessors which have the
required write memory barrier.
A new warning in clang [1] complains that diq_start in
wlc_lcnphy_tx_iqlo_cal() is passed uninitialized as a const pointer to
wlc_lcnphy_common_read_table():
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_lcn.c:2728:13: error: variable 'diq_start' is uninitialized when passed as a const pointer argument here [-Werror,-Wuninitialized-const-pointer]
2728 | &diq_start, 1, 16, 69);
| ^~~~~~~~~
The table pointer passed to wlc_lcnphy_common_read_table() should not be
considered constant, as wlc_phy_read_table() is ultimately going to
update it. Remove the const qualifier from the tbl_ptr to clear up the
warning.
Use common wrappers operating directly on the struct sg_table objects to
fix incorrect use of statterlists related calls. dma_unmap_sg() function
has to be called with the number of elements originally passed to the
dma_map_sg() function, not the one returned in sgtable's nents.
CC: stable@vger.kernel.org Fixes: 425902f5c8e3 ("fpga zynq: Use the scatterlist interface") Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Reviewed-by: Jason Gunthorpe <jgg@nvidia.com> Reviewed-by: Xu Yilun <yilun.xu@intel.com> Link: https://lore.kernel.org/r/20250616120932.1090614-1-m.szyprowski@samsung.com Signed-off-by: Xu Yilun <yilun.xu@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 8ae720449fca ("libata: whitespace fixes in ata_to_sense_error()")
inadvertantly added the entry 0x40 (ATA_DRDY) to the stat_table array in
the function ata_to_sense_error(). This entry ties a failed qc which has
a status filed equal to ATA_DRDY to the sense key ILLEGAL REQUEST with
the additional sense code UNALIGNED WRITE COMMAND. This entry will be
used to generate a failed qc sense key and sense code when the qc is
missing sense data and there is no match for the qc error field in the
sense_table array of ata_to_sense_error().
As a result, for a failed qc for which we failed to get sense data (e.g.
read log 10h failed if qc is an NCQ command, or REQUEST SENSE EXT
command failed for the non-ncq case, the user very often end up seeing
the completely misleading "unaligned write command" error, even if qc
was not a write command. E.g.:
Fix this by removing the ATA_DRDY entry from the stat_table array so
that we default to always returning ABORTED COMMAND without any
additional sense code, since we do not know any better. The entry 0x08
(ATA_DRQ) is also removed since signaling ABORTED COMMAND with a parity
error is also misleading (as a parity error would likely be signaled
through a bus error). So for this case, also default to returning
ABORTED COMMAND without any additional sense code. With this, the
previous example error case becomes:
sd 0:0:0:0: [sda] tag#17 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_OK cmd_age=0s
sd 0:0:0:0: [sda] tag#17 Sense Key : Aborted Command [current]
sd 0:0:0:0: [sda] tag#17 Add. Sense: No additional sense information
sd 0:0:0:0: [sda] tag#17 CDB: Read(10) 28 00 00 00 10 00 00 00 08 00
I/O error, dev sda, sector 4096 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0
Together with these fixes, refactor stat_table to make it more readable
by putting the entries comments in front of the entries and using the
defined status bits macros instead of hardcoded values.
Reported-by: Lorenz Brun <lorenz@brun.one> Reported-by: Brandon Schwartz <Brandon.Schwartz@wdc.com> Fixes: 8ae720449fca ("libata: whitespace fixes in ata_to_sense_error()") Cc: stable@vger.kernel.org Signed-off-by: Damien Le Moal <dlemoal@kernel.org> Reviewed-by: Hannes Reinecke <hare@suse.de> Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In some cases like small FSes with no meta_bg and where the resize
doesn't need extra gdt blocks as it can fit in the current one,
s_reserved_gdt_blocks is set as 0, which causes fsmap to emit a 0
length entry, which is incorrect.
With bigalloc enabled, the logic to report last extent has a bug since
we try to use cluster units instead of block units. This can cause an
issue where extra incorrect entries might be returned back to the
user. This was flagged by generic/365 with 64k bs and -O bigalloc.
** Details of issue **
The issue was noticed on 5G 64k blocksize FS with -O bigalloc which has
only 1 bg.
Only the first entry was expected to be returned but we get 2. This is
because:
ext4_getfsmap_datadev()
first_cluster, last_cluster = 0
...
info->gfi_last = true;
ext4_getfsmap_datadev_helper(sb, end_ag, last_cluster + 1, 0, info);
fsb = C2B(1) = 16
fslen = 0
...
/* Merge in any relevant extents from the meta_list */
list_for_each_entry_safe(p, tmp, &info->gfi_meta_list, fmr_list) {
...
// since fsb = 16, considers all metadata which starts before 16 blockno
iter 1: error = ext4_getfsmap_helper(sb, info, p); // p = sb (0,1), nop
info->gfi_next_fsblk = 1
iter 2: error = ext4_getfsmap_helper(sb, info, p); // p = gdt (1,2), nop
info->gfi_next_fsblk = 2
iter 3: error = ext4_getfsmap_helper(sb, info, p); // p = blk bitmap (2,3), nop
info->gfi_next_fsblk = 3
iter 4: error = ext4_getfsmap_helper(sb, info, p); // p = ino bitmap (18,19)
if (rec_blk > info->gfi_next_fsblk) { // (18 > 3)
// emits an extra entry ** BUG **
}
}
Fix this by directly calling ext4_getfsmap_datadev() with a dummy
record that has fmr_physical set to (end_fsb + 1) instead of
last_cluster + 1. By using the block instead of cluster we get the
correct behavior.
Replacing ext4_getfsmap_datadev_helper() with ext4_getfsmap_helper()
is okay since the gfi_lastfree and metadata checks in
ext4_getfsmap_datadev_helper() are anyways redundant when we only want
to emit the last allocated block of the range, as we have already
taken care of emitting metadata and any last free blocks.
The check for a fast symlink in the presence of only an
external xattr inode is incorrect. If a fast symlink does
not have an xattr block (i_file_acl == 0), but does have
an external xattr inode that increases inode i_blocks, then
the check for a fast symlink will incorrectly fail and
__ext4_iget()->ext4_ind_check_inode() will report the inode
is corrupt when it "validates" i_data[] on the next read:
(note that "block 7303014" = 0x6f6f66 = "foo" in LE order).
ext4_inode_is_fast_symlink() should check the superblock
EXT4_FEATURE_INCOMPAT_EA_INODE feature flag, not the inode
EXT4_EA_INODE_FL, since the latter is only set on the xattr
inode itself, and not on the inode that uses this xattr.
Cc: stable@vger.kernel.org Fixes: fc82228a5e38 ("ext4: support fast symlinks from ext3 file systems") Signed-off-by: Andreas Dilger <adilger@whamcloud.com> Reviewed-by: Li Dongyang <dongyangli@ddn.com> Reviewed-by: Alex Zhuravlev <bzzz@whamcloud.com> Reviewed-by: Oleg Drokin <green@whamcloud.com>
Reviewed-on: https://review.whamcloud.com/59879
Lustre-bug-id: https://jira.whamcloud.com/browse/LU-19121 Link: https://patch.msgid.link/20250717063709.757077-1-adilger@dilger.ca Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The patch is wrong as it checks vc_origin against vc_screenbuf,
while in text mode it should compare against vga_vram_base.
As such it broke VGA text scrolling, which can be reproduced like this:
(1) boot a kernel that is configured to use text mode VGA-console
(2) type commands: ls -l /usr/bin | less -S
(3) scroll up/down with cursor-down/up keys
Reported-by: Jari Ruusu <jariruusu@protonmail.com> Cc: stable@vger.kernel.org Cc: Yi Yang <yiyang13@huawei.com> Cc: GONG Ruiqi <gongruiqi1@huawei.com> Signed-off-by: Helge Deller <deller@gmx.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The MIPS32r2 ChaCha code has never been buildable with the clang
assembler. First, clang doesn't support the 'rotl' pseudo-instruction:
error: unknown instruction, did you mean: rol, rotr?
Second, clang requires that both operands of the 'wsbh' instruction be
explicitly given:
error: too few operands for instruction
To fix this, align the code with the real instruction set by (1) using
the real instruction 'rotr' instead of the nonstandard pseudo-
instruction 'rotl', and (2) explicitly giving both operands to 'wsbh'.
To make removing the use of 'rotl' a bit easier, also remove the
unnecessary special-casing for big endian CPUs at
.Lchacha_mips_xor_bytes. The tail handling is actually
endian-independent since it processes one byte at a time. On big endian
CPUs the old code byte-swapped SAVED_X, then iterated through it in
reverse order. But the byteswap and reverse iteration canceled out.
Tested with chacha20poly1305-selftest in QEMU using "-M malta" with both
little endian and big endian mips32r2 kernels.
Fixes: 49aa7c00eddf ("crypto: mips/chacha - import 32r2 ChaCha code from Zinc") Cc: stable@vger.kernel.org Reported-by: kernel test robot <lkp@intel.com> Closes: https://lore.kernel.org/oe-kbuild-all/202505080409.EujEBwA0-lkp@intel.com/ Link: https://lore.kernel.org/r/20250619225535.679301-1-ebiggers@kernel.org Signed-off-by: Eric Biggers <ebiggers@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The maximum number of keycodes got bumped to 256 a very long time ago,
but the default keymaps were never adjusted to match. This is causing
the kernel to interpret keycodes above 127 as U+0000 if the shipped
generated keymap is used.
Fix this by mapping all keycodes above 127 to K_HOLE so the kernel
ignores them.
The contents of this patche were generated by rerunning `loadkeys
--mktable --unicode` and only including the changes to map keycodes
above 127 to K_HOLE.
We don't process Unicode characters if the virtual terminal is in raw
mode, so there's no reason why we shouldn't do the same for K_OFF
(especially since people would expect K_OFF to actually turn off all VT
key processing).
On big endian platform like PowerPC, the MHI bus (which is little endian)
does not start properly. The following example shows the error messages by
using QCN9274 WLAN device with ath12k driver:
ath12k_pci 0001:01:00.0: BAR 0: assigned [mem 0xc00000000-0xc001fffff 64bit]
ath12k_pci 0001:01:00.0: MSI vectors: 1
ath12k_pci 0001:01:00.0: Hardware name: qcn9274 hw2.0
ath12k_pci 0001:01:00.0: failed to set mhi state: POWER_ON(2)
ath12k_pci 0001:01:00.0: failed to start mhi: -110
ath12k_pci 0001:01:00.0: failed to power up :-110
ath12k_pci 0001:01:00.0: failed to create soc core: -110
ath12k_pci 0001:01:00.0: failed to init core: -110
ath12k_pci: probe of 0001:01:00.0 failed with error -110
The issue seems to be with the incorrect DMA address/size used for
transferring the firmware image over BHI. So fix it by converting the DMA
address and size of the BHI vector table to little endian format before
sending them to the device.
Fixes: 6cd330ae76ff ("bus: mhi: core: Add support for ringing channel/event ring doorbells") Signed-off-by: Alexander Wilhelm <alexander.wilhelm@westermo.com>
[mani: added stable tag and reworded commit message] Signed-off-by: Manivannan Sadhasivam <mani@kernel.org> Reviewed-by: Jeff Hugo <jeff.hugo@oss.qualcomm.com> Reviewed-by: Krishna Chaitanya Chundru <krishna.chundru@oss.qualcomm.com> Cc: stable@vger.kernel.org Link: https://patch.msgid.link/20250519145837.958153-1-alexander.wilhelm@westermo.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After a recent change in clang to expose uninitialized warnings from
const variables [1], there is a warning in cxacru_heavy_init():
drivers/usb/atm/cxacru.c:1104:6: error: variable 'bp' is used uninitialized whenever 'if' condition is false [-Werror,-Wsometimes-uninitialized]
1104 | if (instance->modem_type->boot_rom_patch) {
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/usb/atm/cxacru.c:1113:39: note: uninitialized use occurs here
1113 | cxacru_upload_firmware(instance, fw, bp);
| ^~
drivers/usb/atm/cxacru.c:1104:2: note: remove the 'if' if its condition is always true
1104 | if (instance->modem_type->boot_rom_patch) {
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/usb/atm/cxacru.c:1095:32: note: initialize the variable 'bp' to silence this warning
1095 | const struct firmware *fw, *bp;
| ^
| = NULL
While the warning is technically correct that bp is conditionally passed
uninitialized to cxacru_upload_firmware(), it is ultimately a false
positive warning on the uninitialized use of bp because the same
condition that initializes bp, instance->modem_type->boot_rom_patch, is
the same one that gates the use of bp within cxacru_upload_firmware().
As this warning occurs in clang's frontend before inlining occurs, it
cannot know that these conditions are indentical to avoid the warning.
Manually inline cxacru_upload_firmware() into cxacru_heavy_init(), as
that is its only callsite, so that clang can see that bp is initialized
and used under the same condition, clearing up the warning without any
functional changes to the code (LLVM was already doing this inlining
later).
Move the cursor position rightward after rendering the character,
not before. This avoids complications that arise when the recursive
console_putc call has to wrap the line and/or scroll the display.
This also fixes the linewrap bug that crops off the rightmost column.
When the cursor is at the bottom of the display, a linefeed will not
move the cursor position further downward. Instead, the display scrolls
upward. Avoid the repeated add/subtract sequence by way of a single
subtraction at the initialization of console_struct_num_rows.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Cc: stable@vger.kernel.org Signed-off-by: Finn Thain <fthain@linux-m68k.org> Tested-by: Stan Johnson <userm57@yahoo.com> Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org> Link: https://lore.kernel.org/9d4e8c68a456d5f2bc254ac6f87a472d066ebd5e.1743115195.git.fthain@linux-m68k.org Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The freq_tables[] array has num_possible_cpus() elements so, to avoid an
out of bounds access, this loop should be capped at "< nb_cpus" instead
of "<= nb_cpus". The freq_tables[] array is allocated in
armada_8k_cpufreq_init().
Cc: stable@vger.kernel.org Fixes: f525a670533d ("cpufreq: ap806: add cpufreq driver for Armada 8K") Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org> Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the PSLVERR_RESP_EN parameter is set to 1, the device generates
an error response if an attempt is made to read an empty RBR (Receive
Buffer Register) while the FIFO is enabled.
In serial8250_do_startup(), calling serial_port_out(port, UART_LCR,
UART_LCR_WLEN8) triggers dw8250_check_lcr(), which invokes
dw8250_force_idle() and serial8250_clear_and_reinit_fifos(). The latter
function enables the FIFO via serial_out(p, UART_FCR, p->fcr).
Execution proceeds to the serial_port_in(port, UART_RX).
This satisfies the PSLVERR trigger condition.
When another CPU (e.g., using printk()) is accessing the UART (UART
is busy), the current CPU fails the check (value & ~UART_LCR_SPAR) ==
(lcr & ~UART_LCR_SPAR) in dw8250_check_lcr(), causing it to enter
dw8250_force_idle().
Put serial_port_out(port, UART_LCR, UART_LCR_WLEN8) under the port->lock
to fix this issue.
Currently, the driver performs a length check of the metadata buffer
before the actual metadata size is known and before the metadata is
decided to be copied. This results in valid metadata buffers being
incorrectly marked as invalid.
Move the length check to occur after the metadata size is determined and
is decided to be copied.
Cc: stable@vger.kernel.org Fixes: 088ead255245 ("media: uvcvideo: Add a metadata device node") Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Reviewed-by: Hans de Goede <hansg@kernel.org> Signed-off-by: Ricardo Ribalda <ribalda@chromium.org> Link: https://lore.kernel.org/r/20250707-uvc-meta-v8-1-ed17f8b1218b@chromium.org Signed-off-by: Hans de Goede <hansg@kernel.org> Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The buffer length check before calling uvc_parse_format() only ensured
that the buffer has at least 3 bytes (buflen > 2), buf the function
accesses buffer[3], requiring at least 4 bytes.
This can lead to an out-of-bounds read if the buffer has exactly 3 bytes.
Fix it by checking that the buffer has at least 4 bytes in
uvc_parse_format().
Signed-off-by: Youngjun Lee <yjjuny.lee@samsung.com> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Fixes: c0efd232929c ("V4L/DVB (8145a): USB Video Class driver") Cc: stable@vger.kernel.org Reviewed-by: Ricardo Ribalda <ribalda@chromium.org> Link: https://lore.kernel.org/r/20250610124107.37360-1-yjjuny.lee@samsung.com Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When netpoll is enabled, calling pr_warn_once() while holding
kmemleak_lock in mem_pool_alloc() can cause a deadlock due to lock
inversion with the netconsole subsystem. This occurs because
pr_warn_once() may trigger netpoll, which eventually leads to
__alloc_skb() and back into kmemleak code, attempting to reacquire
kmemleak_lock.
Fix this by setting a flag and issuing the pr_warn_once() after
kmemleak_lock is released.
Link: https://lkml.kernel.org/r/20250731-kmemleak_lock-v1-1-728fd470198f@debian.org Fixes: c5665868183f ("mm: kmemleak: use the memory pool for early allocations") Signed-off-by: Breno Leitao <leitao@debian.org> Reported-by: Jakub Kicinski <kuba@kernel.org> Acked-by: Catalin Marinas <catalin.marinas@arm.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A soft lockup warning was observed on a relative small system x86-64
system with 16 GB of memory when running a debug kernel with kmemleak
enabled.
watchdog: BUG: soft lockup - CPU#8 stuck for 33s! [kworker/8:1:134]
The test system was running a workload with hot unplug happening in
parallel. Then kemleak decided to disable itself due to its inability to
allocate more kmemleak objects. The debug kernel has its
CONFIG_DEBUG_KMEMLEAK_MEM_POOL_SIZE set to 40,000.
The soft lockup happened in kmemleak_do_cleanup() when the existing
kmemleak objects were being removed and deleted one-by-one in a loop via a
workqueue. In this particular case, there are at least 40,000 objects
that need to be processed and given the slowness of a debug kernel and the
fact that a raw_spinlock has to be acquired and released in
__delete_object(), it could take a while to properly handle all these
objects.
As kmemleak has been disabled in this case, the object removal and
deletion process can be further optimized as locking isn't really needed.
However, it is probably not worth the effort to optimize for such an edge
case that should rarely happen. So the simple solution is to call
cond_resched() at periodic interval in the iteration loop to avoid soft
lockup.
Link: https://lkml.kernel.org/r/20250728190248.605750-1-longman@redhat.com Signed-off-by: Waiman Long <longman@redhat.com> Acked-by: Catalin Marinas <catalin.marinas@arm.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If we log a new inode (not persisted in a past transaction) that has 0
links and extents, then log another inode with an higher inode number, we
end up with failing to replay the log tree with -EINVAL. The steps for
this are:
1) create new file A
2) write some data to file A
3) open an fd on file A
4) unlink file A
5) fsync file A using the previously open fd
6) create file B (has higher inode number than file A)
7) fsync file B
8) power fail before current transaction commits
Now when attempting to mount the fs, the log replay will fail with
-ENOENT at replay_one_extent() when attempting to replay the first
extent of file A. The failure comes when trying to open the inode for
file A in the subvolume tree, since it doesn't exist.
Before commit 5f61b961599a ("btrfs: fix inode lookup error handling
during log replay"), the returned error was -EIO instead of -ENOENT,
since we converted any errors when attempting to read an inode during
log replay to -EIO.
The reason for this is that the log replay procedure fails to ignore
the current inode when we are at the stage LOG_WALK_REPLAY_ALL, our
current inode has 0 links and last inode we processed in the previous
stage has a non 0 link count. In other words, the issue is that at
replay_one_extent() we only update wc->ignore_cur_inode if the current
replay stage is LOG_WALK_REPLAY_INODES.
Fix this by updating wc->ignore_cur_inode whenever we find an inode item
regardless of the current replay stage. This is a simple solution and easy
to backport, but later we can do other alternatives like avoid logging
extents or inode items other than the inode item for inodes with a link
count of 0.
The problem with the wc->ignore_cur_inode logic has been around since
commit f2d72f42d5fa ("Btrfs: fix warning when replaying log after fsync
of a tmpfile") but it only became frequent to hit since the more recent
commit 5e85262e542d ("btrfs: fix fsync of files with no hard links not
persisting deletion"), because we stopped skipping inodes with a link
count of 0 when logging, while before the problem would only be triggered
if trying to replay a log tree created with an older kernel which has a
logged inode with 0 links.
syzbot reports a use-after-free in comedi in the below link, which is
due to comedi gladly removing the allocated async area even though poll
requests are still active on the wait_queue_head inside of it. This can
cause a use-after-free when the poll entries are later triggered or
removed, as the memory for the wait_queue_head has been freed. We need
to check there are no tasks queued on any of the subdevices' wait queues
before allowing the device to be detached by the `COMEDI_DEVCONFIG`
ioctl.
Tasks will read-lock `dev->attach_lock` before adding themselves to the
subdevice wait queue, so fix the problem in the `COMEDI_DEVCONFIG` ioctl
handler by write-locking `dev->attach_lock` before checking that all of
the subdevices are safe to be deleted. This includes testing for any
sleepers on the subdevices' wait queues. It remains locked until the
device has been detached. This requires the `comedi_device_detach()`
function to be refactored slightly, moving the bulk of it into new
function `comedi_device_detach_locked()`.
Note that the refactor of `comedi_device_detach()` results in
`comedi_device_cancel_all()` now being called while `dev->attach_lock`
is write-locked, which wasn't the case previously, but that does not
matter.
Thanks to Jens Axboe for diagnosing the problem and co-developing this
patch.
The current power direction of an USB-C port also influences the
power_supply's online status, so a power role change should also update
the power_supply.
Fixes an issue on some systems where plugging in a normal USB device in
for the first time after a reboot will cause upower to erroneously
consider the system to be connected to AC power.
When a card is present in the reader, the driver currently defers
autosuspend by returning -EAGAIN during the suspend callback to
trigger USB remote wakeup signaling. However, this does not guarantee
that the mmc child device has been resumed, which may cause issues if
it remains suspended while the card is accessible.
This patch ensures that all child devices, including the mmc host
controller, are explicitly resumed before returning -EAGAIN. This
fixes a corner case introduced by earlier remote wakeup handling,
improving reliability of runtime PM when a card is inserted.
Fixes: 883a87ddf2f1 ("misc: rtsx_usb: Use USB remote wakeup signaling for card insertion detection") Cc: stable@vger.kernel.org Signed-off-by: Ricky Wu <ricky_wu@realtek.com> Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org> Link: https://lore.kernel.org/r/20250711140143.2105224-1-ricky_wu@realtek.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the regmap_write() for software reset in fsl_sai_config_disable would
cause the FSL_SAI_CSR_BCE bit to be cleared. Refer to
commit 197c53c8ecb34 ("ASoC: fsl_sai: Don't disable bitclock for i.MX8MP")
FSL_SAI_CSR_BCE should not be cleared. So need to use regmap_update_bits()
instead of regmap_write() for these bit operations.
Fixes: dc78f7e59169d ("ASoC: fsl_sai: Force a software reset when starting in consumer mode") Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com> Link: https://patch.msgid.link/20250807020318.2143219-1-shengjiu.wang@nxp.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
dai->probed is used at snd_soc_pcm_dai_probe/remove(),
and used to call real remove() function only when it was probed.
int snd_soc_pcm_dai_probe(...)
{
...
for_each_rtd_dais(rtd, i, dai) {
...
if (dai->driver->probe) {
(A) int ret = dai->driver->probe(dai);
if (ret < 0)
return soc_dai_ret(dai, ret);
}
=> dai->probed = 1;
}
...
}
int snd_soc_pcm_dai_remove(...)
{
...
for_each_rtd_dais(rtd, i, dai) {
...
=> if (dai->probed &&
...) {
...
}
=> dai->probed = 0;
}
...
}
But on probe() case, we need to check dai->probed before calling
real probe() function at (A), otherwise real probe() might be called
multi times (but real remove() will be called only once).
This patch checks it at probe().
In using CONFIG_RTC_HCTOSYS, rtc_hctosys() will sync the RTC time to the
kernel time as long as rtc_read_time() succeeds. In some power loss
situations, our supercapacitor-backed DS1342 RTC comes up with either an
unpredictable future time or the default 01/01/00 from the datasheet.
The oscillator stop flag (OSF) is set in these scenarios due to the
power loss and can be used to determine the validity of the RTC data.
Some chip types in the ds1307 driver already have OSF handling to
determine whether .read_time provides valid RTC data or returns -EINVAL.
This change removes the clear of the OSF in .probe as the OSF needs to
be preserved to expand the OSF handling to the ds1341 chip type (note
that DS1341 and DS1342 share a datasheet).
The error occurs on the third attempt to encode extents. When function
ext_tree_prepare_commit() reallocates a larger buffer to retry encoding
extents, the "layoutupdate_pages" page array is initialized only after the
retry loop. But ext_tree_free_commitdata() is called on every iteration
and tries to put pages in the array, thus dereferencing uninitialized
pointers.
An additional problem is that there is no limit on the maximum possible
buffer_size. When there are too many extents, the client may create a
layoutcommit that is larger than the maximum possible RPC size accepted
by the server.
During testing, we observed two typical scenarios. First, one memory page
for extents is enough when we work with small files, append data to the
end of the file, or preallocate extents before writing. But when we fill
a new large file without preallocating, the number of extents can be huge,
and counting the number of written extents in ext_tree_encode_commit()
does not help much. Since this number increases even more between
unlocking and locking of ext_tree, the reallocated buffer may not be
large enough again and again.
Co-developed-by: Konstantin Evtushenko <koevtushenko@yandex.com> Signed-off-by: Konstantin Evtushenko <koevtushenko@yandex.com> Signed-off-by: Sergey Bashirov <sergeybashirov@gmail.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Link: https://lore.kernel.org/r/20250630183537.196479-2-sergeybashirov@gmail.com Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When there are too many block extents for a layoutcommit, they may not
all fit into the maximum-sized RPC. This patch allows the generic pnfs
code to properly handle -ENOSPC returned by the block/scsi layout driver
and trigger additional layoutcommits if necessary.
Co-developed-by: Konstantin Evtushenko <koevtushenko@yandex.com> Signed-off-by: Konstantin Evtushenko <koevtushenko@yandex.com> Signed-off-by: Sergey Bashirov <sergeybashirov@gmail.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Link: https://lore.kernel.org/r/20250630183537.196479-5-sergeybashirov@gmail.com Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
At the end of the isect translation, disc_addr represents the physical
disk offset. Thus, end calculated from disk_addr is also a physical disk
offset. Therefore, range checking should be done using map->disk_offset,
not map->start.
Because of integer division, we need to carefully calculate the
disk offset. Consider the example below for a stripe of 6 volumes,
a chunk size of 4096, and an offset of 70000.
In blk_stack_limits(), we check that the t->chunk_sectors value is a
multiple of the t->physical_block_size value.
However, by finding the chunk_sectors value in bytes, we may overflow
the unsigned int which holds chunk_sectors, so change the check to be
based on sectors.
Reviewed-by: Hannes Reinecke <hare@suse.de> Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: John Garry <john.g.garry@oracle.com> Reviewed-by: Damien Le Moal <dlemoal@kernel.org> Link: https://lore.kernel.org/r/20250729091448.1691334-2-john.g.garry@oracle.com Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
According to the LAN8710A datasheet (Rev. B, section 3.8.5.1), a hardware
reset is required after power-on, and the reference clock (REF_CLK) must be
established before asserting reset.
The source and destination of some strcpy operations was the same.
Split out the part of the operations that needed to be done for those
particular calls so the unnecessary copy wasn't done.
In case a menu has comment without letters/numbers (eg. characters
matching the regexp '^[^[:alpha:][:digit:]]+$', for example - or *),
hitting space will cycle through those comments, rather than
selecting/deselecting the currently-highlighted option.
This is the behaviour of hitting any letter/digit: jump to the next
option which prompt starts with that letter. The only letters that
do not behave as such are 'y' 'm' and 'n'. Prompts that start with
one of those three letters are instead matched on the first letter
that is not 'y', 'm' or 'n'.
Fix that by treating 'space' as we treat y/m/n, ie. as an action key,
not as shortcut to jump to prompt.
Signed-off-by: Yann E. MORIN <yann.morin.1998@free.fr> Signed-off-by: Peter Korsgaard <peter@korsgaard.com> Signed-off-by: Cherniaev Andrei <dungeonlords789@naver.com>
[masahiro: took from Buildroot, adjusted the commit subject] Signed-off-by: Masahiro Yamada <masahiroy@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The on_treeview2_cursor_changed() handler is connected to both the left
and right tree views, but it hardcodes model2 (the GtkTreeModel of the
right tree view). This is incorrect. Get the associated model from the
view.
During BMC firmware upgrades on live systems, the ipmi_msghandler
generates excessive "BMC returned incorrect response" warnings
while the BMC is temporarily offline. This can flood system logs
in large deployments.
Replace dev_warn() with dev_warn_ratelimited() to throttle these
warnings and prevent log spam during BMC maintenance operations.
When PCI_IRQ_AFFINITY is set for calling pci_alloc_irq_vectors(), it
means interrupts are spread around the available CPUs. It also means that
the interrupts become managed, which means that an interrupt is shutdown
when all the CPUs in the interrupt affinity mask go offline.
Using managed interrupts in this way means that we should ensure that
completions should not occur on HW queues where the associated interrupt
is shutdown. This is typically achieved by ensuring only CPUs which are
online can generate IO completion traffic to the HW queue which they are
mapped to (so that they can also serve completion interrupts for that HW
queue).
The problem in the driver is that a CPU can generate completions to a HW
queue whose interrupt may be shutdown, as the CPUs in the HW queue
interrupt affinity mask may be offline. This can cause IOs to never
complete and hang the system. The driver maintains its own CPU <-> HW
queue mapping for submissions, see aac_fib_vector_assign(), but this does
not reflect the CPU <-> HW queue interrupt affinity mapping.
Commit 9dc704dcc09e ("scsi: aacraid: Reply queue mapping to CPUs based on
IRQ affinity") tried to remedy this issue may mapping CPUs properly to HW
queue interrupts. However this was later reverted in commit c5becf57dd56
("Revert "scsi: aacraid: Reply queue mapping to CPUs based on IRQ
affinity") - it seems that there were other reports of hangs. I guess
that this was due to some implementation issue in the original commit or
maybe a HW issue.
Fix the very original hang by just not using managed interrupts by not
setting PCI_IRQ_AFFINITY. In this way, all CPUs will be in each HW queue
affinity mask, so should not create completion problems if any CPUs go
offline.
Signed-off-by: John Garry <john.g.garry@oracle.com> Link: https://lore.kernel.org/r/20250715111535.499853-1-john.g.garry@oracle.com Closes: https://lore.kernel.org/linux-scsi/20250618192427.3845724-1-jmeneghi@redhat.com/ Reviewed-by: John Meneghini <jmeneghi@redhat.com> Tested-by: John Meneghini <jmeneghi@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
sas_user_scan() did not fully process wildcard channel scans
(SCAN_WILD_CARD) when a transport-specific user_scan() callback was
present. Only channel 0 would be scanned via user_scan(), while the
remaining channels were skipped, potentially missing devices.
user_scan() invokes updated sas_user_scan() for channel 0, and if
successful, iteratively scans remaining channels (1 to
shost->max_channel) via scsi_scan_host_selected(). This ensures complete
wildcard scanning without affecting transport-specific scanning behavior.
strcpy() performs no bounds checking and can lead to buffer overflows if
the input string exceeds the destination buffer size. This patch replaces
it with strncpy(), and null terminates the input string.
This patch fixes an issue where the touchpad cursor movement becomes
slow on the Dell Precision 5560. Force the touchpad freq to 100khz
as a workaround.
Tested on Dell Precision 5560 with 6.14 to 6.14.6. Cursor movement
is now smooth and responsive.
Signed-off-by: fangzhong.zhou <myth5@myth5.com>
[wsa: kept sorting and removed unnecessary parts from commit msg] Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
'I3C_BCR_HDR_CAP' is still spec v1.0 and has been renamed to 'advanced
capabilities' in v1.1 onwards. The ST pressure sensor LPS22DF does not
have HDR, but has the 'advanced cap' bit set. The core still wants to
get additional information using the CCC 'GETHDRCAP' (or GETCAPS in v1.1
onwards). Not all controllers support this CCC and will notify the upper
layers about it. For instantiating the device, we can ignore this
unsupported CCC as standard communication will work. Without this patch,
the device will not be instantiated at all.
In using CONFIG_RTC_HCTOSYS, rtc_hctosys() will sync the RTC time to the
kernel time as long as rtc_read_time() succeeds. In some power loss
situations, our supercapacitor-backed DS1342 RTC comes up with either an
unpredictable future time or the default 01/01/00 from the datasheet.
The oscillator stop flag (OSF) is set in these scenarios due to the
power loss and can be used to determine the validity of the RTC data.
This change expands the oscillator stop flag (OSF) handling that has
already been implemented for some chips to the ds1341 chip (DS1341 and
DS1342 share a datasheet). This handling manages the validity of the RTC
data in .read_time and .set_time based on the OSF.
LKP found a random config which failed to build because IO accessors
were not defined:
In file included from drivers/i3c/master.c:21:
drivers/i3c/internals.h: In function 'i3c_writel_fifo':
>> drivers/i3c/internals.h:35:9: error: implicit declaration of function 'writesl' [-Werror=implicit-function-declaration]
Add the proper header to where the IO accessors are used.
Reported-by: kernel test robot <lkp@intel.com> Closes: https://lore.kernel.org/oe-kbuild-all/202507150208.BZDzzJ5E-lkp@intel.com/ Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Reviewed-by: Frank Li <Frank.Li@nxp.com> Link: https://lore.kernel.org/r/20250717120046.9022-2-wsa+renesas@sang-engineering.com Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fix Smatch-detected error:
drivers/md/dm-zoned-target.c:1073 dmz_iterate_devices()
error: uninitialized symbol 'r'.
Smatch detects a possible use of the uninitialized variable 'r' in
dmz_iterate_devices() because if dmz->nr_ddevs is zero, the loop is
skipped and 'r' is returned without being set, leading to undefined
behavior.
Initialize 'r' to 0 before the loop. This ensures that if there are no
devices to iterate over, the function still returns a defined value.
In w7090p_tuner_write_serpar, msg is controlled by user. When msg[0].buf is null and msg[0].len is zero, former checks on msg[0].buf would be passed. If accessing msg[0].buf[2] without sanity check, null pointer deref would happen. We add
check on msg[0].len to prevent crash.
Similar commit: commit 0ed554fd769a ("media: dvb-usb: az6027: fix null-ptr-deref in az6027_i2c_xfer()")
In dib7090p_rw_on_apb, msg is controlled by user. When msg[0].buf is null and
msg[0].len is zero, former checks on msg[0].buf would be passed. If accessing
msg[0].buf[2] without sanity check, null pointer deref would happen. We add
check on msg[0].len to prevent crash. Similar issue occurs when access
msg[1].buf[0] and msg[1].buf[1].
Similar commit: commit 0ed554fd769a ("media: dvb-usb: az6027: fix null-ptr-deref in az6027_i2c_xfer()")
This driver passes the length of an i2c_msg directly to
usb_control_msg(). If the message is now a read and of length 0, it
violates the USB protocol and a warning will be printed. Enable the
I2C_AQ_NO_ZERO_LEN_READ quirk for this adapter thus forbidding 0-length
read messages altogether.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Sasha Levin <sashal@kernel.org>
The existing fixed value of 16 worked for UYVY 720P60 over
2 lanes at 594MHz, or UYVY 1080P60 over 4 lanes. (RGB888
1080P60 needs 6 lanes at 594MHz).
It doesn't allow for lower resolutions to work as the FIFO
underflows.
374 is required for 1080P24 or 1080P30 UYVY over 2 lanes @
972Mbit/s, but >374 means that the FIFO underflows on 1080P50
UYVY over 2 lanes @ 972Mbit/s.
Whilst it would be nice to compute it, the required information
isn't published by Toshiba.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com> Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Sasha Levin <sashal@kernel.org>
When calling tc358743_set_fmt, the code was calling tc358743_get_fmt
to choose a valid format. However that sets the colorspace
based on information read back from the chip, not the colour
format requested.
The result was that if you called try or set format for UYVY
when the current format was RGB3 then you would get told SRGB,
and try RGB3 when current was UYVY and you would get told
SMPTE170M.
The value programmed in the VI_REP register for the colorspace
is always set by this driver, therefore there is no need to read
back the value, and never set to REC709.
Return the colorspace based on the format set/tried instead.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com> Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Sasha Levin <sashal@kernel.org>
The probe for the TC358743 reads the CHIPID register from
the device and compares it to the expected value of 0.
If the I2C request fails then that also returns 0, so
the driver loads thinking that the device is there.
Generally I2C communications are reliable so there is
limited need to check the return value on every transfer,
therefore only amend the one read during probe to check
for I2C errors.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com> Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Sasha Levin <sashal@kernel.org>
With the ATA error model, an NCQ command failure always triggers an abort
(termination) of all NCQ commands queued on the device. In such case, the
SAT or the host must handle the failed command according to the command
sense data and immediately retry all other NCQ commands that were aborted
due to the failed NCQ command.
For SAS HBAs controlled by the mpt3sas driver, NCQ command aborts are not
handled by the HBA SAT and sent back to the host, with an ioc log
information equal to 0x31080000 (IOC_LOGINFO_PREFIX_PL with the PL code
PL_LOGINFO_CODE_SATA_NCQ_FAIL_ALL_CMDS_AFTR_ERR). The function
_scsih_io_done() always forces a retry of commands terminated with the
status MPI2_IOCSTATUS_SCSI_IOC_TERMINATED using the SCSI result
DID_SOFT_ERROR, regardless of the log_info for the command. This
correctly forces the retry of collateral NCQ abort commands, but with the
retry counter for the command being incremented. If a command to an ATA
device is subject to too many retries due to other NCQ commands failing
(e.g. read commands trying to access unreadable sectors), the collateral
NCQ abort commands may be terminated with an error as they run out of
retries. This violates the SAT specification and causes hard-to-debug
command errors.
Solve this issue by modifying the handling of the
MPI2_IOCSTATUS_SCSI_IOC_TERMINATED status to check if a command is for an
ATA device and if the command loginfo indicates an NCQ collateral
abort. If that is the case, force the command retry using the SCSI result
DID_IMM_RETRY to avoid incrementing the command retry count.
Signed-off-by: Damien Le Moal <dlemoal@kernel.org> Link: https://lore.kernel.org/r/20250606052747.742998-3-dlemoal@kernel.org Tested-by: Yafang Shao <laoar.shao@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
If a call to lpfc_sli4_read_rev() from lpfc_sli4_hba_setup() fails, the
resultant cleanup routine lpfc_sli4_vport_delete_fcp_xri_aborted() may
occur before sli4_hba.hdwqs are allocated. This may result in a null
pointer dereference when attempting to take the abts_io_buf_list_lock for
the first hardware queue. Fix by adding a null ptr check on
phba->sli4_hba.hdwq and early return because this situation means there
must have been an error during port initialization.
The function divides number of online CPUs by num_core_siblings, and
later checks the divider by zero. This implies a possibility to get
and divide-by-zero runtime error. Fix it by moving the check prior to
division. This also helps to save one indentation level.
mc_subled used for multi_index needs well defined array indexes,
to guarantee the desired result, use reg for that.
If devicetree child nodes is processed in random or reverse order
you may end up with multi_index "blue green red" instead of the expected
"red green blue".
If user space apps uses multi_index to deduce how to control the leds
they would most likely be broken without this patch if devicetree
processing is reversed (which it appears to be).
arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-fuji.dts has reg set
but I don't see how it can have worked without this change.
If reg is not set, an error is returned,
If reg is out of range, an error is returned.
reg within led child nodes starts with 0, to map to the iout in each bank.
Signed-off-by: Johan Adolfsson <johan.adolfsson@axis.com> Reviewed-by: Jacek Anaszewski <jacek.anaszewski@gmail.com> Link: https://lore.kernel.org/r/20250617-led-fix-v7-1-cdbe8efc88fa@axis.com Signed-off-by: Lee Jones <lee@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Not all tasks have an ABI associated or vDSO mapped,
for example kthreads never do.
If such a task ever ends up calling stack_top(), it will derefence the
NULL ABI pointer and crash.
When computing the tree index in dbAllocAG, we never check if we are
out of bounds realative to the size of the stree.
This could happen in a scenario where the filesystem metadata are
corrupted.
The reproducer builds a corrupted file on disk with a negative i_size value.
Add a check when opening this file to avoid subsequent operation failures.
Reported-by: syzbot+630f6d40b3ccabc8e96e@syzkaller.appspotmail.com Closes: https://syzkaller.appspot.com/bug?extid=630f6d40b3ccabc8e96e Tested-by: syzbot+630f6d40b3ccabc8e96e@syzkaller.appspotmail.com Signed-off-by: Edward Adam Davis <eadavis@qq.com> Signed-off-by: Dave Kleikamp <dave.kleikamp@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The fileset value of the inode copy from the disk by the reproducer is
AGGR_RESERVED_I. When executing evict, its hard link number is 0, so its
inode pages are not truncated. This causes the bugon to be triggered when
executing clear_inode() because nrpages is greater than 0.
When the bfad_im_probe() function fails during initialization, the memory
pointed to by bfad->im is freed without setting bfad->im to NULL.
Subsequently, during driver uninstallation, when the state machine enters
the bfad_sm_stopping state and calls the bfad_im_probe_undo() function,
it attempts to free the memory pointed to by bfad->im again, thereby
triggering a double-free vulnerability.
These functions are exported but their prototypes are not defined.
This patch adds the missing function prototypes to fix the following
compilation warnings:
arch/mips/kernel/vpe-mt.c:180:7: error: no previous prototype for 'vpe_alloc' [-Werror=missing-prototypes]
180 | void *vpe_alloc(void)
| ^~~~~~~~~
arch/mips/kernel/vpe-mt.c:198:5: error: no previous prototype for 'vpe_start' [-Werror=missing-prototypes]
198 | int vpe_start(void *vpe, unsigned long start)
| ^~~~~~~~~
arch/mips/kernel/vpe-mt.c:208:5: error: no previous prototype for 'vpe_stop' [-Werror=missing-prototypes]
208 | int vpe_stop(void *vpe)
| ^~~~~~~~
arch/mips/kernel/vpe-mt.c:229:5: error: no previous prototype for 'vpe_free' [-Werror=missing-prototypes]
229 | int vpe_free(void *vpe)
| ^~~~~~~~
Signed-off-by: Shiji Yang <yangshiji66@outlook.com> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
The Synopsys Watchdog driver sets the default timeout to 30 seconds,
but on some devices this is not a valid timeout. E.g. on RK3588 the
actual timeout being used is 44 seconds instead.
Once the watchdog is started the value is updated accordingly, but
it would be better to expose a sensible timeout to userspace without
the need to first start the watchdog.
sprintf() is discouraged for use with bounded destination buffers
as it does not prevent buffer overflows when the formatted output
exceeds the destination buffer size. snprintf() is a safer
alternative as it limits the number of bytes written and ensures
NUL-termination.
Replace sprintf() with snprintf() for copying the debug string
into a temporary buffer, using ORANGEFS_MAX_DEBUG_STRING_LEN as
the maximum size to ensure safe formatting and prevent memory
corruption in edge cases.
EDIT: After this patch sat on linux-next for a few days, Dan
Carpenter saw it and suggested that I use scnprintf instead of
snprintf. I made the change and retested.
Signed-off-by: Amir Mohammad Jahangirzad <a.jahangirzad@gmail.com> Signed-off-by: Mike Marshall <hubcap@omnibond.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In case of an ib_fast_reg_mr allocation failure during iSER setup, the
machine hits a panic because iscsi_conn->dd_data is initialized
unconditionally, even when no memory is allocated (dd_size == 0). This
leads invalid pointer dereference during connection teardown.
Fix by setting iscsi_conn->dd_data only if memory is actually allocated.
Signed-off-by: Showrya M N <showrya@chelsio.com> Signed-off-by: Potnuri Bharat Teja <bharat@chelsio.com> Link: https://lore.kernel.org/r/20250627112329.19763-1-showrya@chelsio.com Reviewed-by: Chris Leech <cleech@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
A syzbot fuzzed image triggered a BUG_ON in ext4_update_inline_data()
when an inode had the INLINE_DATA_FL flag set but was missing the
system.data extended attribute.
Since this can happen due to a maiciouly fuzzed file system, we
shouldn't BUG, but rather, report it as a corrupted file system.
Add similar replacements of BUG_ON with EXT4_ERROR_INODE() ii
ext4_create_inline_data() and ext4_inline_data_truncate().
To query root path (without msearch wildcard) it is needed to
send pattern '\' instead of '' (empty string).
This allows to use CIFSFindFirst() to query information about root path
which is being used in followup changes.
This change fixes the stat() syscall called on the root path on the mount.
It is because stat() syscall uses the cifs_query_path_info() function and
it can fallback to the CIFSFindFirst() usage with msearch=false.
Signed-off-by: Pali Rohár <pali@kernel.org> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
This patch fails vhost_add_used_n() early when __vhost_add_used()
fails to make sure used idx is not updated with stale used ring
information.
Reported-by: Eugenio Pérez <eperezma@redhat.com> Signed-off-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20250714084755.11921-2-jasowang@redhat.com> Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Tested-by: Lei Yang <leiyang@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
A decade ago commit 6d08acd2d32e ("in6: fix conflict with glibc")
hid the definitions of IPV6 options, because GCC was complaining
about duplicates. The commit did not list the warnings seen, but
trying to recreate them now I think they are (building iproute2):
In file included from ./include/uapi/rdma/rdma_user_cm.h:39,
from rdma.h:16,
from res.h:9,
from res-ctx.c:7:
../include/uapi/linux/in6.h:171:9: warning: ‘IPV6_ADD_MEMBERSHIP’ redefined
171 | #define IPV6_ADD_MEMBERSHIP 20
| ^~~~~~~~~~~~~~~~~~~
In file included from /usr/include/netinet/in.h:37,
from rdma.h:13:
/usr/include/bits/in.h:233:10: note: this is the location of the previous definition
233 | # define IPV6_ADD_MEMBERSHIP IPV6_JOIN_GROUP
| ^~~~~~~~~~~~~~~~~~~
../include/uapi/linux/in6.h:172:9: warning: ‘IPV6_DROP_MEMBERSHIP’ redefined
172 | #define IPV6_DROP_MEMBERSHIP 21
| ^~~~~~~~~~~~~~~~~~~~
/usr/include/bits/in.h:234:10: note: this is the location of the previous definition
234 | # define IPV6_DROP_MEMBERSHIP IPV6_LEAVE_GROUP
| ^~~~~~~~~~~~~~~~~~~~
Compilers don't complain about redefinition if the defines
are identical, but here we have the kernel using the literal
value, and glibc using an indirection (defining to a name
of another define, with the same numerical value).
Problem is, the commit in question hid all the IPV6 socket
options, and glibc has a pretty sparse list. For instance
it lacks Flow Label related options. Willem called this out
in commit 3fb321fde22d ("selftests/net: ipv6 flowlabel"):
/* uapi/glibc weirdness may leave this undefined */
#ifndef IPV6_FLOWINFO
#define IPV6_FLOWINFO 11
#endif
More interestingly some applications (socat) use
a #ifdef IPV6_FLOWINFO to gate compilation of thier
rudimentary flow label support. (For added confusion
socat misspells it as IPV4_FLOWINFO in some places.)
Hide only the two defines we know glibc has a problem
with. If we discover more warnings we can hide more
but we should avoid covering the entire block of
defines for "IPV6 socket options".
For the evict fail case, the evict error should be returned.
v2: Consider ENOENT case.
v3: Abort directly when the eviction failed for some reason (except for -ENOENT)
and not wait for the move to finish
Signed-off-by: Emily Deng <Emily.Deng@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Christian König <christian.koenig@amd.com> Link: https://lore.kernel.org/r/20250603091154.3472646-1-Emily.Deng@amd.com Signed-off-by: Sasha Levin <sashal@kernel.org>
In NC-SI spec v1.2 section 8.4.44.2, the firmware name doesn't
need to be null terminated while its size occupies the full size
of the field. Fix the buffer overflow issue by adding one
additional byte for null terminator.
BCM5325 doesn't implement GMII_PORT_OVERRIDE_CTRL register so we should
avoid reading or writing it.
PORT_OVERRIDE_RX_FLOW and PORT_OVERRIDE_TX_FLOW aren't defined on BCM5325
and we should use PORT_OVERRIDE_LP_FLOW_25 instead.
In gve_adminq_issue_cmd(), return -EINVAL instead of 0 when an unknown
admin queue command opcode is encountered.
This prevents the function from silently succeeding on invalid input
and prevents undefined behavior by ensuring the function fails gracefully
when an unrecognized opcode is provided.
When CONFIG_VLAN_8021Q=n, a set of stub helpers are used, three of these
helpers use BUG() unconditionally.
This code should not be reached, as callers of these functions should
always check for is_vlan_dev() first, but the usage of BUG() is not
recommended, replace it with WARN_ON() instead.
Reviewed-by: Alex Lazar <alazar@nvidia.com> Reviewed-by: Dragos Tatulea <dtatulea@nvidia.com> Signed-off-by: Gal Pressman <gal@nvidia.com> Link: https://patch.msgid.link/20250616132626.1749331-3-gal@nvidia.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The function `_rtl_pci_init_one_rxdesc()` can fail even when the new
`skb` is passed because of a DMA mapping error. If it fails, the `skb`
is not saved in the rx ringbuffer and thus lost.
projects / thirdparty / kernel / stable.git / log
