In revision 0x20, we use vlan id != 0 to check whether a vlan tag
has been offloaded, so vlan id 0 is not supported.
In revision 0x21, rx buffer descriptor adds two bits to indicate
whether one or more vlan tags have been offloaded, so vlan id 0
is valid now.
This patch seperates the handle for vlan id 0, add vlan id 0 support
for revision 0x21.
Fixes: 5b5455a9ed5a ("net: hns3: Add STRP_TAGP field support for hardware revision 0x21") Signed-off-by: Jian Shen <shenjian15@huawei.com> Signed-off-by: Salil Mehta <salil.mehta@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
A crash in bman portal probing could not be triggered (as is the case
with qman portals) but it does make calls [1] into the bman driver so
lets make sure the bman portal probing happens after bman's.
[1] bman_p_irqsource_add() (in bman) called by:
init_pcfg() called by:
bman_portal_probe()
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com> Signed-off-by: Li Yang <leoyang.li@nxp.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
A certain silead controller (Chip ID: 0x56810000) loses its firmware
after suspend, causing the resume to fail. This patch tries to load
the firmware, should a resume error occur and retries the resuming.
Signed-off-by: Julian Sax <jsbc@gmx.de> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When an io error is hit, it calls gfs2_io_error_bh_i for every
journal buffer it can't write. Since we changed gfs2_io_error_bh_i
recently to withdraw later in the cycle, it sends a flood of
errors to the console. This patch checks for the file system already
being withdrawn, and if so, doesn't send more messages. It doesn't
stop the flood of messages, but it slows it down and keeps it more
reasonable.
Signed-off-by: Bob Peterson <rpeterso@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
If a receive is in progress or starts before the transmit has
a chance, then lower the Signal Free Time of the upcoming transmit
to no more than CEC_SIGNAL_FREE_TIME_NEW_INITIATOR.
Running "./nfstest_delegation --runtest recall26" uncovers that
client doesn't recover the lock when we have an appending open,
where the initial open got a write delegation.
Instead of checking for the passed in open context against
the file lock's open context. Check that the state is the same.
ARCH_BCM_63XX which is used by ARM-based DSL SoCs from Broadcom uses the
same controller, make it possible to select the STB driver and update
the Kconfig and help text a bit.
clk_notifier_register() documentation states, that the provided notifier
callbacks associated with the notifier must not re-enter into the clk
framework by calling any top-level clk APIs. Fix this by replacing
clk_get_rate() calls with clk_hw_get_rate(), which is safe in this
context.
The bit of GATE_BUS_PERIS1 for CLK_SECKEY is just reserved on
exynos5422/5800, not exynos5420. Define gate clk for exynos5420 to
handle the bit only on exynos5420.
SoC clock drivers should suspend after every other drivers in the system,
which are using clocks and resume before them. The last stage for calling
suspend device callbacks is NOIRQ stage and there exists driver, which use
that state (dwmmc-exynos), so Exynos5433 clocks driver should also use it.
During the same stage, clocks driver will be always suspended after its
clients as a direct result of proper device probe order (deferred probe
reorders the suspend call sequence).
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Acked-by: Chanwoo Choi <cw00.choi@samsung.com> Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org> Signed-off-by: Sylwester Nawrocki <snawrocki@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
On disconnect wireless core attempts to remove all the supported keys.
Following cfg80211_ops conventions, firmware returns -ENOENT code
for the out-of-bound key indexes. This is a normal behavior,
so no need to report errors for this case.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Driver retrieves information about supported extended capabilities
from wireless card. However this information is not propagated
further to Linux wireless core. Fix this by setting extended
capabilities fields of wiphy structure.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
SGI should be passed to wireless core as a part of rate structure.
Otherwise wireless core performs incorrect rate calculation when
SGI is enabled in hardware but not reported to host.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In case firmware reports that it can not do OBSS scanning for 40MHz
2.4GHz channels itself, tell userpsace to do that instead by setting
NL80211_FEATURE_NEED_OBSS_SCAN flag.
Signed-off-by: Igor mitsyanko <igor.mitsyanko.os@quantenna.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The driver sends an action frame down and waits for a completion signal
triggered by the received BRCMF_E_ACTION_FRAME_OFF_CHAN_COMPLETE event
to continue the process. However, the action frame could be transmitted
either on the current channel or on an off channel. For the on-channel
case, only BRCMF_E_ACTION_FRAME_COMPLETE event will be received when
the frame is transmitted, which make the driver always wait a full
timeout duration. This patch has the completion signal be triggered by
receiving the BRCMF_E_ACTION_FRAME_COMPLETE event for the on-channel
case.
This change fixes WFA p2p certification 5.1.19 failure.
Signed-off-by: Chung-Hsien Hsu <stanley.hsu@cypress.com> Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Finding a common channel to send an action frame out is required for
some action types. Since a loop with several scan retry is used to find
the channel, a short wait time could be considered for each attempt.
This patch reduces the wait time from 1500 to 450 msec for each action
frame scan.
This patch fixes the WFA p2p certification 5.1.20 failure caused by the
long action frame send time.
Signed-off-by: Chung-Hsien Hsu <stanley.hsu@cypress.com> Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When booting with "nosmt=force" a message is issued into dmesg to
confirm that SMT has been force-disabled but such a message is not
issued when only "nosmt" is on the kernel command line.
During probe, if there was an error the memory region and the memory
map were not properly released.This can lead a system unusable if
deferred probe is in use.
Replace mem_request and map with devm_ioremap_resource
The bug would let the usb controller enter partial power down,
which was formally known as hibernate, upon boot if nothing was plugged
in to the port. Partial power down couldn't be exited properly, so any
usb devices plugged in after boot would not be usable.
Before the name change, params.hibernation was false by default, so
_dwc2_hcd_suspend() would skip entering hibernation. With the
rename, _dwc2_hcd_suspend() was changed to use params.power_down
to decide whether or not to enter partial power down.
Since params.power_down is non-zero by default, it needs to be set
to 0 for rockchip devices to restore functionality.
This bug was reported in the linux-usb thread:
REGRESSION: usb: dwc2: USB device not seen after boot
Fix interrupt-out transfer length which was being set to the
transfer-buffer length rather than the size of the outgoing packet.
Note that no slab data was leaked as the whole transfer buffer is always
cleared before each transfer.
Fixes: 9aa8dae7b1fa ("cypress_m8: use usb_fill_int_urb where appropriate") Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When an OS (currently only classic Mac OS) is running in KVM-PR and makes a
linked jump from code with split hack addressing enabled into code that does
not, LR is not correctly updated and reflects the previously munged PC.
To fix this, this patch undoes the address munge when exiting split
hack mode so that code relying on LR being a proper address will now
execute. This does not affect OS X or other operating systems running
on KVM-PR.
Signed-off-by: Cameron Kaiser <spectre@floodgap.com> Signed-off-by: Paul Mackerras <paulus@ozlabs.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Return proper error code when Firmware returns
HWRM_ERR_CODE_RESOURCE_ACCESS_DENIED for HWRM_NVM_GET/SET_VARIABLE
commands.
Cc: Michael Chan <michael.chan@broadcom.com> Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The Elo VuPoint 15MX has two headphone jacks of which neither work by
default. Disabling automute allows ALSA to work normally with the
speakers & left headphone jack.
Future pin configuration changes may be required in the future to get
the right headphone jack working in tandem.
Currently the adv748x driver will fail to probe unless both of its
output endpoints (TXA and TXB) are connected.
Make the driver support probing provided that there is at least one
input, and one output connected and protect the clean-up function from
accessing un-initialized fields.
Following patches will fix other uses of un-initialized TXs in the driver,
such as power management functions.
When adding support for parallel subdev for Gen3 it was missed that the
symbol 'i' in rvin_group_link_notify() was already declared, remove the
dupe as it's only used as a loop variable this have no functional
change. This fixes warning:
rcar-core.c:117:52: originally declared here
rcar-core.c:173:30: warning: symbol 'i' shadows an earlier one
Clang warns when one enumerated type is implicitly converted to another.
drivers/net/ethernet/qlogic/qed/qed_ll2.c:799:32: warning: implicit
conversion from enumeration type 'enum core_tx_dest' to different
enumeration type 'enum qed_ll2_tx_dest' [-Wenum-conversion]
tx_pkt.tx_dest = p_ll2_conn->tx_dest;
~ ~~~~~~~~~~~~^~~~~~~
1 warning generated.
Fix this by using a switch statement to convert between the enumerated
values since they are not 1 to 1, which matches how the rest of the
driver handles this conversion.
Link: https://github.com/ClangBuiltLinux/linux/issues/125 Suggested-by: Tomer Tayar <Tomer.Tayar@cavium.com> Signed-off-by: Nathan Chancellor <natechancellor@gmail.com> Acked-by: Tomer Tayar <Tomer.Tayar@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Clang warns when one enumerated type is implicitly converted to another.
drivers/ata/pata_ep93xx.c:662:36: warning: implicit conversion from
enumeration type 'enum dma_data_direction' to different enumeration type
'enum dma_transfer_direction' [-Wenum-conversion]
drv_data->dma_rx_data.direction = DMA_FROM_DEVICE;
~ ^~~~~~~~~~~~~~~
drivers/ata/pata_ep93xx.c:670:36: warning: implicit conversion from
enumeration type 'enum dma_data_direction' to different enumeration type
'enum dma_transfer_direction' [-Wenum-conversion]
drv_data->dma_tx_data.direction = DMA_TO_DEVICE;
~ ^~~~~~~~~~~~~
drivers/ata/pata_ep93xx.c:681:19: warning: implicit conversion from
enumeration type 'enum dma_data_direction' to different enumeration type
'enum dma_transfer_direction' [-Wenum-conversion]
conf.direction = DMA_FROM_DEVICE;
~ ^~~~~~~~~~~~~~~
drivers/ata/pata_ep93xx.c:692:19: warning: implicit conversion from
enumeration type 'enum dma_data_direction' to different enumeration type
'enum dma_transfer_direction' [-Wenum-conversion]
conf.direction = DMA_TO_DEVICE;
~ ^~~~~~~~~~~~~
Use the equivalent valued enums from the expected type so that Clang no
longer warns about a conversion.
Local radix TLB flush operations that operate on congruence classes
have explicit ERAT flushes for POWER9. The process scoped LPID flush
did not have a flush, so add it.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
We currently cap the decrementer clockevent at 4 seconds, even on systems
with large decrementer support. Fix this by converting the code to use
clockevents_register_device() which calculates the upper bound based on
the max_delta passed in.
Signed-off-by: Anton Blanchard <anton@ozlabs.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
If the CPU exits the "polling" state due to the time limit in the
loop in poll_idle(), this is not a real wakeup and it just means
that the "polling" state selection was not adequate. The governor
mispredicted short idle duration, but had a more suitable state been
selected, the CPU might have spent more time in it. In fact, there
is no reason to expect that there would have been a wakeup event
earlier than the next timer in that case.
Handling such cases as regular wakeups in menu_update() may cause the
menu governor to make suboptimal decisions going forward, but ignoring
them altogether would not be correct either, because every time
menu_select() is invoked, it makes a separate new attempt to predict
the idle duration taking distinct time to the closest timer event as
input and the outcomes of all those attempts should be recorded.
For this reason, make menu_update() always assume that if the
"polling" state was exited due to the time limit, the next proper
wakeup event for the CPU would be the next timer event (not
including the tick).
Fixes: a37b969a61c1 "cpuidle: poll_state: Add time limit to poll_idle()" Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Reviewed-by: Daniel Lezcano <daniel.lezcano@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
These address spaces are defined by the ACPI spec to be
"always available", and thus _REG should never be run on them.
Provides compatibility with other ACPI implementations.
Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Erik Schmauss <erik.schmauss@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The point of the 'force_dma' parameter for of_dma_configure
is to force the device to be set up even if DMA capability is
not described by the firmware which is exactly the use case
we have for GMU - we need SMMU to get set up but we have no
other dma capabilities since memory is managed by the GPU
driver. Currently we pass false so of_dma_configure() fails
and subsequently GMU and GPU probe does as well.
Fixes: 4b565ca5a2c ("drm/msm: Add A6XX device support") Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org> Tested-by: Sibi Sankar <sibis@codeaurora.org> Signed-off-by: Rob Clark <robdclark@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Clang warns when one enumerated type is implicitly converted to another.
drivers/infiniband/hw/mlx4/mad.c:1811:41: warning: implicit conversion
from enumeration type 'enum mlx4_ib_qp_flags' to different enumeration
type 'enum ib_qp_create_flags' [-Wenum-conversion]
qp_init_attr.init_attr.create_flags = MLX4_IB_SRIOV_TUNNEL_QP;
~ ^~~~~~~~~~~~~~~~~~~~~~~
drivers/infiniband/hw/mlx4/mad.c:1819:41: warning: implicit conversion
from enumeration type 'enum mlx4_ib_qp_flags' to different enumeration
type 'enum ib_qp_create_flags' [-Wenum-conversion]
qp_init_attr.init_attr.create_flags = MLX4_IB_SRIOV_SQP;
~ ^~~~~~~~~~~~~~~~~
The type mlx4_ib_qp_flags explicitly provides supplemental values to the
type ib_qp_create_flags. Make that clear to Clang by changing the
create_flags type to u32.
Reported-by: Nick Desaulniers <ndesaulniers@google.com> Signed-off-by: Nathan Chancellor <natechancellor@gmail.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The hip08 split two hardware version. The version id are 0x20 and 0x21
according to the PCI revison. The max size of extend sge of sq is limited
to 2M for 0x20 version and 8M for 0x21 version. It may be exceeded to 2M
according to the algorithm that compute the product of wqe count and
extend sge number of every wqe. But the product always less than 8M.
Signed-off-by: Lijun Ou <oulijun@huawei.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
It will print the warning when the MSB bit of SLID is not zero running
cm_req_handler function that test CM. It needs to fixed zero when test
RoCE device.
Signed-off-by: Lijun Ou <oulijun@huawei.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In rxe_queue_init, q and q->buf are allocated. In do_mmap_info, q->ip is
allocated. When error occurs, rxe_srq_from_init and the later error
handler do not free these allocated memories. This will make memory leak.
This patch fix crash when we have restore flow director filters after reset
adapter. In ixgbe_fdir_filter_restore() filter->action is outside of the
rx_ring array, as it has a VF identifier in the upper 32 bits.
Signed-off-by: Radoslaw Tyl <radoslawx.tyl@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Clang warns when one enumerated type is converted implicitly to another.
drivers/net/ethernet/intel/i40e/i40e_virtchnl_pf.c:4214:42: warning:
implicit conversion from enumeration type 'enum i40e_aq_link_speed' to
different enumeration type 'enum virtchnl_link_speed'
[-Wenum-conversion]
pfe.event_data.link_event.link_speed = I40E_LINK_SPEED_40GB;
~ ^~~~~~~~~~~~~~~~~~~~
1 warning generated.
Use the proper enum from virtchnl_link_speed, which has the same value
as I40E_LINK_SPEED_40GB, VIRTCHNL_LINK_SPEED_40GB. This appears to be
missed by commit ff3f4cc267f6 ("virtchnl: finish conversion to virtchnl
interface").
Link: https://github.com/ClangBuiltLinux/linux/issues/81 Signed-off-by: Nathan Chancellor <natechancellor@gmail.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit 35bfc52187f6 ("md: allow metadata update while suspending.")
added support for allowing md_check_recovery() to still perform
metadata updates while the array is entering the 'suspended' state.
This is needed to allow the processes of entering the state to
complete.
Unfortunately, the patch doesn't really work. The test for
"mddev->suspended" at the start of md_check_recovery() means that the
function doesn't try to do anything at all while entering suspend.
This patch moves the code of updating the metadata while suspending to
*before* the test on mddev->suspended.
Reported-by: Jeff Mahoney <jeffm@suse.com> Fixes: 35bfc52187f6 ("md: allow metadata update while suspending.") Signed-off-by: NeilBrown <neilb@suse.com> Signed-off-by: Shaohua Li <shli@fb.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The driver seems to abuse *unsigned long* not only for the (32-bit)
register values but also for the 'sh_cmt_channel::total_cycles' which
needs to always be 64-bit -- as a result, the clocksource's mask is
needlessly clamped down to 32-bits on the 32-bit machines...
Fixes: 19bdc9d061bc ("clocksource: sh_cmt clocksource support") Reported-by: Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Reviewed-by: Simon Horman <horms+renesas@verge.net.au> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When trying to use CMT for clockevents on R-Car gen3 SoCs, I noticed
that 'max_delta_ns' for the broadcast timer (CMT) was shown as 1000 in
/proc/timer_list. It turned out that when calculating it, the driver did
1 << 32 (causing what I think was undefined behavior) resulting in a zero
delta, later clamped to 1000 by cev_delta2ns(). The root cause turned out
to be that the driver abused *unsigned long* for the CMT register values
(which are 16/32-bit), so that the calculation of 'ch->max_match_value'
in sh_cmt_setup_channel() used the wrong branch. Using more proper 'u32'
instead fixed 'max_delta_ns' and even fixed the switching an active
clocksource to CMT (which caused the system to turn non-interactive
before).
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently if get_e820_md5() fails, then it will hibernate nevertheless.
Actually the error code should be propagated to upper caller so that
the hibernation could be aware of the result and terminates the process
if md5 digest fails.
Suggested-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Pavel Machek <pavel@ucw.cz> Signed-off-by: Chen Yu <yu.c.chen@intel.com> Acked-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Clang warns when one enumerated type is converted implicitly to another:
drivers/mtd/nand/raw/sh_flctl.c:483:46: warning: implicit conversion
from enumeration type 'enum dma_transfer_direction' to different
enumeration type 'enum dma_data_direction' [-Wenum-conversion]
flctl_dma_fifo0_transfer(flctl, buf, rlen, DMA_DEV_TO_MEM) > 0)
~~~~~~~~~~~~~~~~~~~~~~~~^~~~~~~~~~~~~~
drivers/mtd/nand/raw/sh_flctl.c:542:46: warning: implicit conversion
from enumeration type 'enum dma_transfer_direction' to different
enumeration type 'enum dma_data_direction' [-Wenum-conversion]
flctl_dma_fifo0_transfer(flctl, buf, rlen, DMA_MEM_TO_DEV) > 0)
~~~~~~~~~~~~~~~~~~~~~~~~^~~~~~~~~~~~~~
2 warnings generated.
Use the proper enums from dma_data_direction to satisfy Clang.
When CONFIG_VIRT_CPU_ACCOUNTING_NATIVE is not set, we look up dtl_idx in
the lppaca to determine the number of entries in the buffer. Since
lppaca is in big endian, we need to do an endian conversion before using
this in our calculation to determine the number of entries in the
buffer. Without this, we do not iterate over the existing entries in the
DTL buffer properly.
When CONFIG_VIRT_CPU_ACCOUNTING_NATIVE is not set, we register the DTL
buffer for a cpu when the associated file under powerpc/dtl in debugfs
is opened. When doing so, we need to set the size of the buffer being
registered in the second u32 word of the buffer. This needs to be in big
endian, but we are not doing the conversion resulting in the below error
showing up in dmesg:
dtl_start: DTL registration for cpu 0 (hw 0) failed with -4
Clang warns when one enumerated type is implicitly converted to another.
drivers/net/ethernet/chelsio/cxgb4/cxgb4_dcb.c:390:4: warning: implicit
conversion from enumeration type 'enum cxgb4_dcb_state' to different
enumeration type 'enum cxgb4_dcb_state_input' [-Wenum-conversion]
IEEE_FAUX_SYNC(dev, dcb);
^~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/ethernet/chelsio/cxgb4/cxgb4_dcb.h:70:10: note: expanded
from macro 'IEEE_FAUX_SYNC'
CXGB4_DCB_STATE_FW_ALLSYNCED);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~
Use the equivalent value of the expected type to silence Clang while
resulting in no functional change.
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com> Reviewed-by: Nick Desaulniers <ndesaulniers@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Clang warns when one enumerated type is implicitly converted to another.
drivers/net/ethernet/chelsio/cxgb4/cxgb4_dcb.c:303:7: warning: implicit
conversion from enumeration type 'enum cxgb4_dcb_state' to different
enumeration type 'enum cxgb4_dcb_state_input' [-Wenum-conversion]
? CXGB4_DCB_STATE_FW_ALLSYNCED
^~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/ethernet/chelsio/cxgb4/cxgb4_dcb.c:304:7: warning: implicit
conversion from enumeration type 'enum cxgb4_dcb_state' to different
enumeration type 'enum cxgb4_dcb_state_input' [-Wenum-conversion]
: CXGB4_DCB_STATE_FW_INCOMPLETE);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~
2 warnings generated.
Use the equivalent value of the expected type to silence Clang while
resulting in no functional change.
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com> Reviewed-by: Nick Desaulniers <ndesaulniers@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
A root port Device ID changed between simulation and production. Rather
than match Device IDs which may not be future-proof if left unmaintained,
match all root ports which exist in a VMD domain.
For TCP, the logic in xprt_connect_status is currently never invoked
to record a successful connection. Commit 2a4919919a97 ("SUNRPC:
Return EAGAIN instead of ENOTCONN when waking up xprt->pending")
changed the way TCP xprt's are awoken after a connect succeeds.
Instead, change connection-oriented transports to bump connect_count
and compute connect_time the moment that XPRT_CONNECTED is set.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
E.g. for snd_hdac_ext_bus_link_power_up(), we should set mask to be
AZX_MLCTL_SPA(it was 0), and AZX_MLCTL_SPA as value to power up it,
here correct it and several similar mismatches.
Clang warns when implicitly converting from one enumerated type to
another. Avoid this by using the equivalent value from the expected
type.
drivers/dma/timb_dma.c:548:27: warning: implicit conversion from
enumeration type 'enum dma_transfer_direction' to different enumeration
type 'enum dma_data_direction' [-Wenum-conversion]
td_desc->desc_list_len, DMA_MEM_TO_DEV);
^~~~~~~~~~~~~~
1 warning generated.
Reported-by: Nick Desaulniers <ndesaulniers@google.com> Signed-off-by: Nathan Chancellor <natechancellor@gmail.com> Reviewed-by: Nick Desaulniers <ndesaulniers@google.com> Signed-off-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Clang warns when implicitly converting from one enumerated type to
another. Avoid this by using the equivalent value from the expected
type.
In file included from drivers/dma/ep93xx_dma.c:30:
./include/linux/platform_data/dma-ep93xx.h:88:10: warning: implicit
conversion from enumeration type 'enum dma_data_direction' to different
enumeration type 'enum dma_transfer_direction' [-Wenum-conversion]
return DMA_NONE;
~~~~~~ ^~~~~~~~
1 warning generated.
Reported-by: Nick Desaulniers <ndesaulniers@google.com> Signed-off-by: Nathan Chancellor <natechancellor@gmail.com> Reviewed-by: Nick Desaulniers <ndesaulniers@google.com> Signed-off-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
CON_PRINTBUFFER console registration requires us to do several
preparation steps:
- Rollback console_seq to replay logbuf messages which were already
seen on other consoles;
- Set exclusive_console flag so console_unlock() will ->write() logbuf
messages only to the exclusive_console driver.
We rollback console_seq under logbuf_lock with IRQs disabled, but
we set exclusive_console with local IRQs enabled and logbuf unlocked.
If the system oops-es or panic-s before we set exclusive_console - and
given that we have IRQs and preemption enabled there is such a
possibility - we will re-play all logbuf messages to every registered
console, which may be a bit annoying and time consuming.
Move exclusive_console assignment to the same IRQs-disabled and
logbuf_lock-protected section where we rollback console_seq.
Link: http://lkml.kernel.org/r/20180928095304.9972-1-sergey.senozhatsky@gmail.com
To: Steven Rostedt <rostedt@goodmis.org> Cc: Sergey Senozhatsky <sergey.senozhatsky.work@gmail.com> Cc: linux-kernel@vger.kernel.org Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com> Signed-off-by: Petr Mladek <pmladek@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
We return H_TOO_HARD from TCE update handlers when we think that
the next handler (realmode -> virtual mode -> user mode) has a chance to
handle the request; H_HARDWARE/H_CLOSED otherwise.
This changes the handlers to return H_TOO_HARD on every error giving
the userspace an opportunity to handle any request or at least log
them all.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru> Reviewed-by: David Gibson <david@gibson.dropbear.id.au> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
We want to go into a sane state when unregistering. Currently, it
happens that the watchdog stops when unbinding because of RuntimePM
stopping the core clock. When rebinding, the core clock gets reactivated
and the watchdog fires even though it hasn't been opened by userspace
yet. Strange scenario, yes, but sane state is much preferred anyhow.
watchdog_stop() calls watchdog_update_worker() which needs a valid
wdd->wd_data pointer. So, when unregistering the cdev, clear the
pointers after we call watchdog_stop(), not before.
The irq_domain structure has an host_data pointer that just stores
private data. It is meant to not be touched by the IRQ core. However,
when it comes to MSI, the MSI layer adds its own private data there
with a structure that also has a host_data pointer.
Because this IRQ domain is an MSI domain, to access private data we
should do a d->host_data->host_data, also wrapped as
'platform_msi_get_host_data()'.
This bug was lying there silently because the 'icu' structure retrieved
this way was just called by dev_err(), only producing a
'(NULL device *):' output on the console.
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Use the NL80211_KEY_IDX attribute inside the NL80211_ATTR_KEY in
NL80211_CMD_GET_KEY responses to comply with nl80211_key_policy.
This is unlikely to affect existing userspace.
Signed-off-by: Andrew Zaborowski <andrew.zaborowski@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When operating in USB 2.0 speeds (HS/FS), if GUSB2PHYCFG.ENBLSLPM or
GUSB2PHYCFG.SUSPHY is set, it must be cleared before issuing an endpoint
command.
Current implementation only save and restore GUSB2PHYCFG.SUSPHY
configuration. We must save and clear both GUSB2PHYCFG.ENBLSLPM and
GUSB2PHYCFG.SUSPHY settings. Restore them after the command is
completed.
DWC_usb3 3.30a and DWC_usb31 1.90a programming guide section 3.2.2
TLS test cases splice_from_pipe, send_and_splice &
recv_peek_multiple_records expect to receive a given nummber of bytes
and then compare them against the number of bytes which were sent.
Therefore, system call recv() must not return before receiving the
requested number of bytes, otherwise the subsequent memcmp() fails.
This patch passes MSG_WAITALL flag to recv() so that it does not return
prematurely before requested number of bytes are copied to receive
buffer.
Signed-off-by: Vakul Garg <vakul.garg@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Since the debug print code is outside of the loop, it shouldn't use the loop
iterator anymore but instead print the found maximum index.
Cc: Nick Kossifidis <mickflemm@gmail.com> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
device_release() is freeing the resources before calling the device
specific release callback which is, in the case of devfreq, stopping
the governor.
It is a problem as some governors are using the device resources. e.g.
simpleondemand which is using the devfreq deferrable monitoring work. If it
is not stopped before the resources are freed, it might lead to a use after
free.
Signed-off-by: Vincent Donnefort <vincent.donnefort@arm.com> Reviewed-by: John Einar Reitan <john.reitan@arm.com>
[cw00.choi: Fix merge conflict] Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com> Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit ab8f58ad72c4 ("PM / devfreq: Set min/max_freq when adding the
devfreq device") initializes df->min/max_freq with the min/max OPP when
the device is added. Later commit f1d981eaecf8 ("PM / devfreq: Use the
available min/max frequency") adds df->scaling_min/max_freq and the
following to the frequency adjustment code:
With the current handling of min/max_freq this is incorrect:
Even though df->max_freq is now initialized to a value != 0 user space
can still set it to 0, in this case max_freq would be 0 instead of
df->scaling_max_freq as intended. In consequence the frequency adjustment
is not performed:
if (max_freq && freq > max_freq) {
freq = max_freq;
To fix this set df->min/max freq to the min/max OPP in max/max_freq_store,
when the user passes a value of 0. This also prevents df->max_freq from
being set below the min OPP when df->min_freq is 0, and similar for
min_freq. Since it is now guaranteed that df->min/max_freq can't be 0 the
checks for this case can be removed.
Fixes: f1d981eaecf8 ("PM / devfreq: Use the available min/max frequency") Signed-off-by: Matthias Kaehlcke <mka@chromium.org> Reviewed-by: Brian Norris <briannorris@chromium.org> Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com> Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When the devfreq driver and the governor driver are built as modules,
the call to devfreq_add_device() or governor_store() fails because the
governor driver is not loaded at the time the devfreq driver loads. The
devfreq driver has a build dependency on the governor but also should
have a runtime dependency. We need to make sure that the governor driver
is loaded before the devfreq driver.
This patch fixes this bug by adding a try_then_request_governor()
function. First tries to find the governor, and then, if it is not found,
it requests the module and tries again.
Fixes: 1b5c1be2c88e (PM / devfreq: map devfreq drivers to governor using name) Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com> Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com> Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Clang warns when one enumerated type is implicitly converted to another.
drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtcoutsrc.c:1327:34:
warning: implicit conversion from enumeration type 'enum
btc_chip_interface' to different enumeration type 'enum
wifionly_chip_interface' [-Wenum-conversion]
wifionly_cfg->chip_interface = BTC_INTF_PCI;
~ ^~~~~~~~~~~~
drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtcoutsrc.c:1330:34:
warning: implicit conversion from enumeration type 'enum
btc_chip_interface' to different enumeration type 'enum
wifionly_chip_interface' [-Wenum-conversion]
wifionly_cfg->chip_interface = BTC_INTF_USB;
~ ^~~~~~~~~~~~
drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtcoutsrc.c:1333:34:
warning: implicit conversion from enumeration type 'enum
btc_chip_interface' to different enumeration type 'enum
wifionly_chip_interface' [-Wenum-conversion]
wifionly_cfg->chip_interface = BTC_INTF_UNKNOWN;
~ ^~~~~~~~~~~~~~~~
3 warnings generated.
Use the values from the correct enumerated type, wifionly_chip_interface.
The vdev-start-response message should cause the
completion to fire, even in the error case. Otherwise,
the user still gets no useful information and everything
is blocked until the timeout period.
Add some warning text to print out the invalid status
code to aid debugging, and propagate failure code.
Signed-off-by: Ben Greear <greearb@candelatech.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The dummy node ID is marked into all memory ranges on the system. So the
dummy node really extends the entire memblock.memory. Hence report correct
extent information for the dummy node using memblock range helper functions
instead of the range [0LLU, PFN_PHYS(max_pfn) - 1)].
Fixes: 1a2db30034 ("arm64, numa: Add NUMA support for arm64 platforms") Acked-by: Punit Agrawal <punit.agrawal@arm.com> Signed-off-by: Anshuman Khandual <anshuman.khandual@arm.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
So far we have only supported 3 level page table with fixed IPA of
40bits, where PUD is folded. With 4 level page tables, we need
to check if the PUD entry is valid or not. Fix stage2_flush_memslot()
to do this check, before walking down the table.
Acked-by: Christoffer Dall <cdall@kernel.org> Acked-by: Marc Zyngier <marc.zyngier@arm.com> Reviewed-by: Eric Auger <eric.auger@redhat.com> Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
in the __arm_smmu_sync_poll_msi() polling loop requires that sync_idx
must be increased monotonically according to the sequence of the CMDs in
the cmdq.
However, since the msidata is populated using atomic_inc_return_relaxed()
before taking the command-queue spinlock, then the following scenario
can occur:
CPU0 CPU1
msidata=0
msidata=1
insert cmd1
insert cmd0
smmu execute cmd1
smmu execute cmd0
poll timeout, because msidata=1 is overridden by
cmd0, that means VAL=0, sync_idx=1.
This is not a functional problem, since the caller will eventually either
timeout or exit due to another CMD_SYNC, however it's clearly not what
the code is supposed to be doing. Fix it, by incrementing the sequence
count with the command-queue lock held, allowing us to drop the atomic
operations altogether.
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
[will: dropped the specialised cmd building routine for now] Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / thirdparty / kernel / stable.git / log
