We have a race between marking that an inode needs to be logged, either
at btrfs_set_inode_last_trans() or at btrfs_page_mkwrite(), and between
btrfs_sync_log(). The following steps describe how the race happens.
1) We are at transaction N;
2) Inode I was previously fsynced in the current transaction so it has:
inode->logged_trans set to N;
3) The inode's root currently has:
root->log_transid set to 1
root->last_log_commit set to 0
Which means only one log transaction was committed to far, log
transaction 0. When a log tree is created we set ->log_transid and
->last_log_commit of its parent root to 0 (at btrfs_add_log_tree());
4) One more range of pages is dirtied in inode I;
5) Some task A starts an fsync against some other inode J (same root), and
so it joins log transaction 1.
Before task A calls btrfs_sync_log()...
6) Task B starts an fsync against inode I, which currently has the full
sync flag set, so it starts delalloc and waits for the ordered extent
to complete before calling btrfs_inode_in_log() at btrfs_sync_file();
7) During ordered extent completion we have btrfs_update_inode() called
against inode I, which in turn calls btrfs_set_inode_last_trans(),
which does the following:
So ->last_trans is set to N and ->last_sub_trans set to 1.
But before setting ->last_log_commit...
8) Task A is at btrfs_sync_log():
- it increments root->log_transid to 2
- starts writeback for all log tree extent buffers
- waits for the writeback to complete
- writes the super blocks
- updates root->last_log_commit to 1
It's a lot of slow steps between updating root->log_transid and
root->last_log_commit;
9) The task doing the ordered extent completion, currently at
btrfs_set_inode_last_trans(), then finally runs:
Which results in inode->last_log_commit being set to 1.
The ordered extent completes;
10) Task B is resumed, and it calls btrfs_inode_in_log() which returns
true because we have all the following conditions met:
inode->logged_trans == N which matches fs_info->generation &&
inode->last_subtrans (1) <= inode->last_log_commit (1) &&
inode->last_subtrans (1) <= root->last_log_commit (1) &&
list inode->extent_tree.modified_extents is empty
And as a consequence we return without logging the inode, so the
existing logged version of the inode does not point to the extent
that was written after the previous fsync.
It should be impossible in practice for one task be able to do so much
progress in btrfs_sync_log() while another task is at
btrfs_set_inode_last_trans() right after it reads root->log_transid and
before it reads root->last_log_commit. Even if kernel preemption is enabled
we know the task at btrfs_set_inode_last_trans() can not be preempted
because it is holding the inode's spinlock.
However there is another place where we do the same without holding the
spinlock, which is in the memory mapped write path at:
So with preemption happening after setting ->last_sub_trans and before
setting ->last_log_commit, it is less of a stretch to have another task
do enough progress at btrfs_sync_log() such that the task doing the memory
mapped write ends up with ->last_sub_trans and ->last_log_commit set to
the same value. It is still a big stretch to get there, as the task doing
btrfs_sync_log() has to start writeback, wait for its completion and write
the super blocks.
So fix this in two different ways:
1) For btrfs_set_inode_last_trans(), simply set ->last_log_commit to the
value of ->last_sub_trans minus 1;
2) For btrfs_page_mkwrite() only set the inode's ->last_sub_trans, just
like we do for buffered and direct writes at btrfs_file_write_iter(),
which is all we need to make sure multiple writes and fsyncs to an
inode in the same transaction never result in an fsync missing that
the inode changed and needs to be logged. Turn this into a helper
function and use it both at btrfs_page_mkwrite() and at
btrfs_file_write_iter() - this also fixes the problem that at
btrfs_page_mkwrite() we were setting those fields without the
protection of the inode's spinlock.
This is an extremely unlikely race to happen in practice.
Signed-off-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Anand Jain <anand.jain@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Function "dma_map_sg" is entitled to merge adjacent entries
and return a value smaller than what was passed as "nents".
Subsequently "ib_map_mr_sg" needs to work with this value ("sg_dma_len")
rather than the original "nents" parameter ("sg_len").
This old RDS bug was exposed and reliably causes kernel panics
(using RDMA operations "rds-stress -D") on x86_64 starting with:
commit c588072bba6b ("iommu/vt-d: Convert intel iommu driver to the iommu ops")
When booted with multiple displays attached, the EFI GOP driver on (at
least) Ampere, can leave DP links powered up that aren't being used to
display anything. This confuses our tracking of SOR routing, with the
likely result being a failed modeset and display engine hang.
Fix this by (ab?)using the DisableLT IED script to power-down the link,
restoring HW to a state the driver expects.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com> Reviewed-by: Lyude Paul <lyude@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
[Why]
Userspace should get back a copy of drm_wait_vblank that's been modified
even when drm_wait_vblank_ioctl returns a failure.
Rationale:
drm_wait_vblank_ioctl modifies the request and expects the user to read
it back. When the type is RELATIVE, it modifies it to ABSOLUTE and updates
the sequence to become current_vblank_count + sequence (which was
RELATIVE), but now it became ABSOLUTE.
drmWaitVBlank (in libdrm) expects this to be the case as it modifies
the request to be Absolute so it expects the sequence to would have been
updated.
The change is in compat_drm_wait_vblank, which is called by
drm_compat_ioctl. This change of copying the data back regardless of the
return number makes it en par with drm_ioctl, which always copies the
data before returning.
[How]
Return from the function after everything has been copied to user.
Fixes IGT:kms_flip::modeset-vs-vblank-race-interruptible
Tested on ChromeOS Trogdor(msm)
Inside blk_mq_queue_tag_busy_iter() we already grabbed request's
refcount before calling ->fn(), so needn't to grab it one more time
in blk_mq_check_expired().
Meantime remove extra request expire check in blk_mq_check_expired().
Cc: Keith Busch <kbusch@kernel.org> Signed-off-by: Ming Lei <ming.lei@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: John Garry <john.garry@huawei.com> Link: https://lore.kernel.org/r/20210811155202.629575-1-ming.lei@redhat.com Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
As __vringh_iov() traverses a descriptor chain, it populates
each descriptor entry into either read or write vring iov
and increments that iov's ->used member. So, as we iterate
over a descriptor chain, at any point, (riov/wriov)->used
value gives the number of descriptor enteries available,
which are to be read or written by the device. As all read
iovs must precede the write iovs, wiov->used should be zero
when we are traversing a read descriptor. Current code checks
for wiov->i, to figure out whether any previous entry in the
current descriptor chain was a write descriptor. However,
iov->i is only incremented, when these vring iovs are consumed,
at a later point, and remain 0 in __vringh_iov(). So, correct
the check for read and write descriptor order, to use
wiov->used.
Acked-by: Jason Wang <jasowang@redhat.com> Reviewed-by: Stefano Garzarella <sgarzare@redhat.com> Signed-off-by: Neeraj Upadhyay <neeraju@codeaurora.org> Link: https://lore.kernel.org/r/1624591502-4827-1-git-send-email-neeraju@codeaurora.org Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Do not call vDPA drivers' callbacks with vq indicies larger than what
the drivers indicate that they support. vDPA drivers do not bounds
check the indices.
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com> Link: https://lore.kernel.org/r/20210701114652.21956-1-vincent.whitchurch@axis.com Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Acked-by: Jason Wang <jasowang@redhat.com> Reviewed-by: Stefano Garzarella <sgarzare@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When a virtio pci device undergo surprise removal (aka async removal in
PCIe spec), mark the device as broken so that any upper layer drivers can
abort any outstanding operation.
When a virtio net pci device undergo surprise removal which is used by a
NetworkManager, a below call trace was observed.
Currently vq->broken field is read by virtqueue_is_broken() in busy
loop in one context by virtnet_send_command().
vq->broken is set to true in other process context by
virtio_break_device(). Reader and writer are accessing it without any
synchronization. This may lead to a compiler optimization which may
result to optimize reading vq->broken only once.
Hence, force reading vq->broken on each invocation of
virtqueue_is_broken() and also force writing it so that such
update is visible to the readers.
It is a theoretical fix that isn't yet encountered in the field.
Some products (So) may have two different types of products
with different mac-type that are otherwise equivalent, and
have the same PNVM data, so the PNVM file will contain two
(or perhaps later more) HW-type TLVs. Accept the file and
use the data section that contains any matching entry.
The probe was manually passing NULL instead of dev to devm_clk_hw_register.
This caused a Unable to handle kernel NULL pointer dereference error.
Fix this by passing 'dev'.
Signed-off-by: Adam Ford <aford173@gmail.com> Fixes: a20a40a8bbc2 ("clk: renesas: rcar-usb2-clock-sel: Fix error handling in .probe()") Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The u32 variable pci_dword is being masked with 0x1fffffff and then left
shifted 23 places. The shift is a u32 operation,so a value of 0x200 or
more in pci_dword will overflow the u32 and only the bottow 32 bits
are assigned to addr. I don't believe this was the original intent.
Fix this by casting pci_dword to a resource_size_t to ensure no
overflow occurs.
Note that the mask and 12 bit left shift operation does not need this
because the mask SNR_IMC_MMIO_MEM0_MASK and shift is always a 32 bit
value.
Fixes: ee49532b38dd ("perf/x86/intel/uncore: Add IMC uncore support for Snow Ridge")
Addresses-Coverity: ("Unintentional integer overflow") Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Signed-off-by: Ingo Molnar <mingo@kernel.org> Reviewed-by: Kan Liang <kan.liang@linux.intel.com> Link: https://lore.kernel.org/r/20210706114553.28249-1-colin.king@canonical.com Signed-off-by: Sasha Levin <sashal@kernel.org>
When the schema fixups are applied to 'select' the result is a single
entry is required for a match, but that will never match as there should
be 2 entries. Also, a 'select' schema should have the widest possible
match, so use 'contains' which matches the compatible string(s) in any
position and not just the first position.
If the endpoint completion callback is call right after the ep_enabled flag
is cleared and before usb_ep_dequeue() is call, we could do a double free
on the request and the associated buffer.
Fix this by clearing ep_enabled after all the endpoint requests have been
dequeued.
A small race exists between intel_gt_retire_requests_timeout and
intel_timeline_exit which could result in the syncmap not getting
free'd. Rather than work to hard to seal this race, simply cleanup the
syncmap on fini.
Fixes: b60189e0392f ("net: stmmac: Integrate EST with TAPRIO scheduler API") Cc: <stable@vger.kernel.org> # 5.10.x Signed-off-by: Wong Vee Khee <vee.khee.wong@linux.intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Add a mutex lock to protect est structure parameters so that the
EST parameters can be updated by other threads.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Pavel Machek (CIP) <pavel@denx.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
It turned out that the change from the reverted commit breaks the ACPI
based rpi's because it causes the 100Mhz max clock to be overridden to the
return from sdhci_iproc_get_max_clock(), which is 0 because there isn't a
OF/DT based clock device.
Reported-by: Jeremy Linton <jeremy.linton@arm.com> Fixes: 419dd626e357 ("mmc: sdhci-iproc: Set SDHCI_QUIRK_CAP_CLOCK_BASE_BROKEN on BCM2711") Acked-by: Stefan Wahren <stefan.wahren@i2se.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently, when query PFC configuration by dcbtool, driver will return
PFC enable status based on TC. As all priorities are mapped to TC0 by
default, if TC0 is enabled, then all priorities mapped to TC0 will be
shown as enabled status when query PFC setting, even though some
priorities have never been set.
for example:
$ dcb pfc show dev eth0
pfc-cap 4 macsec-bypass off delay 0
prio-pfc 0:off 1:off 2:off 3:off 4:off 5:off 6:off 7:off
$ dcb pfc set dev eth0 prio-pfc 0:on 1:on 2:on 3:on
$ dcb pfc show dev eth0
pfc-cap 4 macsec-bypass off delay 0
prio-pfc 0:on 1:on 2:on 3:on 4:on 5:on 6:on 7:on
To fix this problem, just returns user's PFC config parameter saved in
driver.
Fixes: cacde272dd00 ("net: hns3: Add hclge_dcb module for the support of DCB feature") Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
VLAN list should not be added duplicate VLAN node, otherwise it would
cause "add failed" when restore VLAN from VLAN list, so this patch adds
VLAN ID check before adding node into VLAN list.
After the cmdq registers are cleared, the firmware may take time to
clear out possible left over commands in the cmdq. Driver must release
cmdq memory only after firmware has completed processing of left over
commands.
Fixes: 232d0d55fca6 ("net: hns3: uninitialize command queue while unloading PF driver") Signed-off-by: Yufeng Mo <moyufeng@huawei.com> Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
If a PF is bonded to a virtual machine and the virtual machine exits
unexpectedly, some hardware resource cannot be cleared. In this case,
loading driver may cause exceptions. Therefore, the hardware resource
needs to be cleared when the driver is loaded.
Currently when device is moved between network namespaces using
RTM_NEWLINK message type and one of netns attributes (FLA_NET_NS_PID,
IFLA_NET_NS_FD, IFLA_TARGET_NETNSID) but w/o specifying IFLA_IFNAME, and
target namespace already has device with same name, userspace will get
EINVAL what is confusing and makes debugging harder.
Fix it so that userspace gets more appropriate EEXIST instead what makes
debugging much easier.
Before:
# ./ifname.sh
+ ip netns add ns0
+ ip netns exec ns0 ip link add l0 type dummy
+ ip netns exec ns0 ip link show l0
8: l0: <BROADCAST,NOARP> mtu 1500 qdisc noop state DOWN mode DEFAULT group default qlen 1000
link/ether 66:90:b5:d5:78:69 brd ff:ff:ff:ff:ff:ff
+ ip link add l0 type dummy
+ ip link show l0
10: l0: <BROADCAST,NOARP> mtu 1500 qdisc noop state DOWN mode DEFAULT group default qlen 1000
link/ether 6e:c6:1f:15:20:8d brd ff:ff:ff:ff:ff:ff
+ ip link set l0 netns ns0
RTNETLINK answers: Invalid argument
After:
# ./ifname.sh
+ ip netns add ns0
+ ip netns exec ns0 ip link add l0 type dummy
+ ip netns exec ns0 ip link show l0
8: l0: <BROADCAST,NOARP> mtu 1500 qdisc noop state DOWN mode DEFAULT group default qlen 1000
link/ether 1e:4a:72:e3:e3:8f brd ff:ff:ff:ff:ff:ff
+ ip link add l0 type dummy
+ ip link show l0
10: l0: <BROADCAST,NOARP> mtu 1500 qdisc noop state DOWN mode DEFAULT group default qlen 1000
link/ether f2:fc:fe:2b:7d:a6 brd ff:ff:ff:ff:ff:ff
+ ip link set l0 netns ns0
RTNETLINK answers: File exists
The problem is that do_setlink() passes its `char *ifname` argument,
that it gets from a caller, to __dev_change_net_namespace() as is (as
`const char *pat`), but semantics of ifname and pat can be different.
, i.e. do_setlink() gets ifname pointer that is always valid no matter
if user specified IFLA_IFNAME or not and then do_setlink() passes this
ifname pointer as is to __dev_change_net_namespace() as pat argument.
But the pat (pattern) in __dev_change_net_namespace() is used as:
net/core/dev.c
11198 err = -EEXIST;
11199 if (__dev_get_by_name(net, dev->name)) {
11200 /* We get here if we can't use the current device name */
11201 if (!pat)
11202 goto out;
11203 err = dev_get_valid_name(net, dev, pat);
11204 if (err < 0)
11205 goto out;
11206 }
As the result the `goto out` path on line 11202 is neven taken and
instead of returning EEXIST defined on line 11198,
__dev_change_net_namespace() returns an error from dev_get_valid_name()
and this, in turn, will be EINVAL for ifname[0] = '\0' set earlier.
Fixes: d8a5ec672768 ("[NET]: netlink support for moving devices between network namespaces.") Signed-off-by: Andrey Ignatov <rdna@fb.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
When adapter init fails, the blocked freelist bitmap is already freed
up and should not be touched. So, move the bitmap zeroing closer to
where it was successfully allocated. Also handle adapter init failure
unwind path immediately and avoid setting up RDMA memory windows.
Fixes: 5b377d114f2b ("cxgb4: Add debugfs facility to inject FL starvation") Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
A group of security researchers brought to our attention
the weakness of hash function used in rt6_exception_hash()
Lets use siphash instead of Jenkins Hash, to considerably
reduce security risks.
Following patch deals with IPv4.
Fixes: 35732d01fe31 ("ipv6: introduce a hash table to store dst cache") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: Keyu Man <kman001@ucr.edu> Cc: Wei Wang <weiwan@google.com> Cc: Martin KaFai Lau <kafai@fb.com> Acked-by: Wei Wang <weiwan@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
When the change() function decreases the value of 'nstrict', we must take
into account that packets might be already enqueued on a class that flips
from 'strict' to 'quantum': otherwise that class will not be added to the
bandwidth-sharing list. Then, a call to ets_qdisc_reset() will attempt to
do list_del(&alist) with 'alist' filled with zero, hence the NULL pointer
dereference.
For classes flipping from 'strict' to 'quantum', initialize an empty list
and eventually add it to the bandwidth-sharing list, if there are packets
already enqueued. In this way, the kernel will:
a) prevent crashing as described above.
b) avoid retaining the backlog packets (for an arbitrarily long time) in
case no packet is enqueued after a change from 'strict' to 'quantum'.
Reported-by: Hangbin Liu <liuhangbin@gmail.com> Fixes: dcc68b4d8084 ("net: sch_ets: Add a new Qdisc") Signed-off-by: Davide Caratti <dcaratti@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
We need to increment the ucounts reference counter befor security_prepare_creds()
because this function may fail and abort_creds() will try to decrement
this reference.
According to Armada XP datasheet bit at 0 position is corresponding for
TxInProg indication.
Fixes: c5aff18204da ("net: mvneta: driver for Marvell Armada 370/XP network unit") Signed-off-by: Maxim Kiselev <bigunclemax@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
A successful 'xge_mdio_config()' call should be balanced by a corresponding
'xge_mdio_remove()' call in the error handling path of the probe, as
already done in the remove function.
Update the error handling path accordingly.
Fixes: ea8ab16ab225 ("drivers: net: xgene-v2: Add MDIO support") Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Validate csum_start in gre_handle_offloads before we call _gre_xmit so
that we do not crash later when the csum_start value is used in the
lco_csum function call.
This patch deals with ipv4 code.
Fixes: c54419321455 ("GRE: Refactor GRE tunneling code.") Reported-by: syzbot+ff8e1b9f2f36481e2efc@syzkaller.appspotmail.com Signed-off-by: Shreyansh Chouhan <chouhan.shreyansh630@gmail.com> Reviewed-by: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
On new platforms, the NVM is read-only. Attempting to update the NVM
is causing a lockup to occur. Do not attempt to write to the NVM
on platforms where it's not supported.
Emit an error message when the NVM checksum is invalid.
We should decode the latency and the max_latency before directly compare.
The latency should be presented as lat_enc = scale x value:
lat_enc_d = (lat_enc & 0x0x3ff) x (1U << (5*((max_ltr_enc & 0x1c00)
>> 10)))
Fixes: cf8fb73c23aa ("e1000e: add support for LTR on I217/I218") Suggested-by: Yee Li <seven.yi.lee@gmail.com> Signed-off-by: Sasha Neftin <sasha.neftin@intel.com> Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Use num_tx_queues rather than the IGC_MAX_TX_QUEUES fixed number 4 when
iterating over tx_ring queue since instantiated queue count could be
less than 4 where on-line cpu count is less than 4.
Fixes: ec50a9d437f0 ("igc: Add support for taprio offloading") Signed-off-by: Toshiki Nishioka <toshiki.nishioka@intel.com> Signed-off-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com> Tested-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com> Acked-by: Sasha Neftin <sasha.neftin@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
After unplug thunderbolt dock with i225, pciehp interrupt is triggered,
remove call will read/write mmio address which is already disconnected,
then cause page fault and make system hang.
Fixes: 13b5b7fd6a4a ("igc: Add support for Tx/Rx rings") Fixes: b03c49cde61f ("igc: Save PTP time before a reset") Signed-off-by: Aaron Ma <aaron.ma@canonical.com> Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
- restore the behavior in enable_net_traffic() to avoid regressions - Jakub
Kicinski;
- hurried up and removed redundant assignment in pegasus_open() before yet
another checker complains;
Fixes: 8a160e2e9aeb ("net: usb: pegasus: Check the return value of get_geristers() and friends;") Reported-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Petko Manolov <petko.manolov@konsulko.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The devlink dev info command reports version information about the
device and firmware running on the board. This includes the "board.id"
field which is supposed to represent an identifier of the board design.
The ice driver uses the Product Board Assembly identifier for this.
In some cases, the PBA is not present in the NVM. If this happens,
devlink dev info will fail with an error. Instead, modify the
ice_info_pba function to just exit without filling in the context
buffer. This will cause the board.id field to be skipped. Log a dev_dbg
message in case someone wants to confirm why board.id is not showing up
for them.
Fixes: e961b679fb0b ("ice: add board identifier info to devlink .info_get") Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Tony Brelinski <tonyx.brelinski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Link: https://lore.kernel.org/r/20210819223451.245613-1-anthony.l.nguyen@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The fixed commit removes all rtnl_lock() and rtnl_unlock() calls in
function bnxt_re_dev_init(), but forgets to remove a rtnl_unlock() in the
error handling path of bnxt_re_register_netdev(), which may cause a
deadlock. This bug is suggested by a static analysis tool.
Fixes: c2b777a95923 ("RDMA/bnxt_re: Refactor device add/remove functionalities") Link: https://lore.kernel.org/r/20210816085531.12167-1-dinghao.liu@zju.edu.cn Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn> Acked-by: Selvin Xavier <selvin.xavier@broadcom.com> Reviewed-by: Jason Gunthorpe <jgg@nvidia.com> Signed-off-by: Jason Gunthorpe <jgg@nvidia.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
kmalloc_array() is called to allocate memory for tx->descp. If it fails,
the function __sdma_txclean() is called:
__sdma_txclean(dd, tx);
However, in the function __sdma_txclean(), tx-descp is dereferenced if
tx->num_desc is not zero:
sdma_unmap_desc(dd, &tx->descp[0]);
To fix this possible null-pointer dereference, assign the return value of
kmalloc_array() to a local variable descp, and then assign it to tx->descp
if it is not NULL. Otherwise, go to enomem.
Fixes: 7724105686e7 ("IB/hfi1: add driver files") Link: https://lore.kernel.org/r/20210806133029.194964-1-islituo@gmail.com Reported-by: TOTE Robot <oslab@tsinghua.edu.cn> Signed-off-by: Tuo Li <islituo@gmail.com> Tested-by: Mike Marciniszyn <mike.marciniszyn@cornelisnetworks.com> Acked-by: Mike Marciniszyn <mike.marciniszyn@cornelisnetworks.com> Signed-off-by: Jason Gunthorpe <jgg@nvidia.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
blk_mq_run_hw_queues
^^^^^^ dispatch IO, q_usage_counter will reduce to zero
blk_mq_unfreeze_queue
^^^^^ mq_freeze_depth--
To fix this, we need to run queue before rescanning device when the device
state changes to SDEV_RUNNING.
Link: https://lore.kernel.org/r/20210824025921.3277629-1-lijinlin3@huawei.com Fixes: f0f82e2476f6 ("scsi: core: Fix capacity set to zero after offlinining device") Reviewed-by: Bart Van Assche <bvanassche@acm.org> Signed-off-by: Li Jinlin <lijinlin3@huawei.com> Signed-off-by: Qiu Laibin <qiulaibin@huawei.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During a USB cable disconnect, or soft disconnect scenario, a pending
SETUP transaction may not be completed, leading to the following
error:
dwc3 a600000.dwc3: timed out waiting for SETUP phase
If this occurs, then the entire pullup disable routine is skipped and
proper cleanup and halting of the controller does not complete.
Instead of returning an error (which is ignored from the UDC
perspective), allow the pullup disable routine to continue, which
will also handle disabling of EP0/1. This will end any active
transfers as well. Ensure to clear any delayed_status also, as the
timeout could happen within the STATUS stage.
Fixes: bb0147364850 ("usb: dwc3: gadget: don't clear RUN/STOP when it's invalid to do so") Cc: <stable@vger.kernel.org> Reviewed-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com> Acked-by: Felipe Balbi <balbi@kernel.org> Signed-off-by: Wesley Cheng <wcheng@codeaurora.org> Link: https://lore.kernel.org/r/20210825042855.7977-1-wcheng@codeaurora.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We can't depend on the TRB's HWO bit to determine if the TRB ring is
"full". A TRB is only available when the driver had processed it, not
when the controller consumed and relinquished the TRB's ownership to the
driver. Otherwise, the driver may overwrite unprocessed TRBs. This can
happen when many transfer events accumulate and the system is slow to
process them and/or when there are too many small requests.
If a request is in the started_list, that means there is one or more
unprocessed TRBs remained. Check this instead of the TRB's HWO bit
whether the TRB ring is full.
The recent attempt to handle an unknown ROM state in the commit d143825baf15 ("usb: renesas-xhci: Fix handling of unknown ROM state")
resulted in a regression and reverted later by the commit 44cf53602f5a
("Revert "usb: renesas-xhci: Fix handling of unknown ROM state"").
The problem of the former fix was that it treated the failure of
firmware loading as a fatal error. Since the firmware files aren't
included in the standard linux-firmware tree, most users don't have
them, hence they got the non-working system after that. The revert
fixed the regression, but also it didn't make the firmware loading
triggered even on the devices that do need it. So we need still a fix
for them.
This is another attempt to handle the unknown ROM state. Like the
previous fix, this also tries to load the firmware when ROM shows
unknown state. In this patch, however, the failure of a firmware
loading (such as a missing firmware file) isn't handled as a fatal
error any longer when ROM has been already detected, but it falls back
to the ROM mode like before. The error is returned only when no ROM
is detected and the firmware loading failed.
Along with it, for simplifying the code flow, the detection and the
check of ROM is factored out from renesas_fw_check_running() and done
in the caller side, renesas_xhci_check_request_fw(). It avoids the
redundant ROM checks.
The patch was tested on Lenovo Thinkpad T14 gen (BIOS 1.34). Also it
was confirmed that no regression is seen on another Thinkpad T14
machine that has worked without the patch, too.
These devices do not appear to send a zero-length packet when the
transfer size is a multiple of the bulk-endpoint max-packet size. This
means that incoming data may not be processed by the driver until a
short packet is received or the receive buffer is full.
Revert back to using endpoint-sized receive buffers to avoid stalled
reads.
schedule_delayed_work does not push back the work if it was already
scheduled before, so amdgpu_device_delay_enable_gfx_off ran ~100 ms
after the first time GFXOFF was disabled and re-enabled, even if GFXOFF
was disabled and re-enabled again during those 100 ms.
This resulted in frame drops / stutter with the upcoming mutter 41
release on Navi 14, due to constantly enabling GFXOFF in the HW and
disabling it again (for getting the GPU clock counter).
To fix this, call cancel_delayed_work_sync when the disable count
transitions from 0 to 1, and only schedule the delayed work on the
reverse transition, not if the disable count was already 0. This makes
sure the delayed work doesn't run at unexpected times, and allows it to
be lock-free.
v2:
* Use cancel_delayed_work_sync & mutex_trylock instead of
mod_delayed_work.
v3:
* Make amdgpu_device_delay_enable_gfx_off lock-free (Christian König)
v4:
* Fix race condition between amdgpu_gfx_off_ctrl incrementing
adev->gfx.gfx_off_req_count and amdgpu_device_delay_enable_gfx_off
checking for it to be 0 (Evan Quan)
Cc: stable@vger.kernel.org Reviewed-by: Evan Quan <evan.quan@amd.com> Reviewed-by: Lijo Lazar <lijo.lazar@amd.com> # v3 Acked-by: Christian König <christian.koenig@amd.com> # v3 Signed-off-by: Michel Dänzer <mdaenzer@redhat.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[BUG]
It's no longer possible to create compressed inline extent after commit f2165627319f ("btrfs: compression: don't try to compress if we don't
have enough pages").
[CAUSE]
For compression code, there are several possible reasons we have a range
that needs to be compressed while it's no more than one page.
- Compressed inline write
The data is always smaller than one sector and the test lacks the
condition to properly recognize a non-inline extent.
- Compressed subpage write
For the incoming subpage compressed write support, we require page
alignment of the delalloc range.
And for 64K page size, we can compress just one page into smaller
sectors.
For those reasons, the requirement for the data to be more than one page
is not correct, and is already causing regression for compressed inline
data writeback. The idea of skipping one page to avoid wasting CPU time
could be revisited in the future.
[FIX]
Fix it by reverting the offending commit.
Reported-by: Zygo Blaxell <ce3g8jdj@umail.furryterror.org> Link: https://lore.kernel.org/linux-btrfs/afa2742.c084f5d6.17b6b08dffc@tnonline.net Fixes: f2165627319f ("btrfs: compression: don't try to compress if we don't have enough pages") CC: stable@vger.kernel.org # 4.4+ Signed-off-by: Qu Wenruo <wqu@suse.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The value of FP registers in the core dump file comes from the
thread.fstate. However, kernel saves the FP registers to the thread.fstate
only before scheduling out the process. If no process switch happens
during the exception handling process, kernel will not have a chance to
save the latest value of FP registers to thread.fstate. It will cause the
value of FP registers in the core dump file may be incorrect. To solve this
problem, this patch force lets kernel save the FP register into the
thread.fstate if the target task_struct equals the current.
Signed-off-by: Vincent Chen <vincent.chen@sifive.com> Reviewed-by: Jisheng Zhang <jszhang@kernel.org> Fixes: b8c8a9590e4f ("RISC-V: Add FP register ptrace support for gdb.") Cc: stable@vger.kernel.org Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ceph_cap_flush structures are usually dynamically allocated, but
the ceph_cap_snap has an embedded one.
When force umounting, the client will try to remove all the session
caps. During this, it will free them, but that should not be done
with the ones embedded in a capsnap.
Fix this by adding a new boolean that indicates that the cap flush is
embedded in a capsnap, and skip freeing it if that's set.
At the same time, switch to using list_del_init() when detaching the
i_list and g_list heads. It's possible for a forced umount to remove
these objects but then handle_cap_flushsnap_ack() races in and does the
list_del_init() again, corrupting memory.
Cc: stable@vger.kernel.org
URL: https://tracker.ceph.com/issues/52283 Signed-off-by: Xiubo Li <xiubli@redhat.com> Reviewed-by: Jeff Layton <jlayton@kernel.org> Signed-off-by: Ilya Dryomov <idryomov@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes the interchanged fetch of the CAN RX and TX error
counters from the ESD_EV_CAN_ERROR_EXT message. The RX error counter
is really in struct rx_msg::data[2] and the TX error counter is in
struct rx_msg::data[3].
Fixes: 96d8e90382dc ("can: Add driver for esd CAN-USB/2 device") Link: https://lore.kernel.org/r/20210825215227.4947-2-stefan.maetje@esd.eu Cc: stable@vger.kernel.org Signed-off-by: Stefan Mätje <stefan.maetje@esd.eu> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ocelot driver makes use of regmap, wrapping it with driver specific
operations that are thin wrappers around the core regmap APIs. These are
exported with EXPORT_SYMBOL, dropping the _GPL from the core regmap
exports which is frowned upon. Add _GPL suffixes to at least the APIs that
are doing register I/O.
Signed-off-by: Mark Brown <broonie@kernel.org> Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
One error path can result in release_dentry_name_snapshot() being called
before "name" was initialized by take_dentry_name_snapshot().
Fix by moving the release_dentry_name_snapshot() to immediately after the
only use.
Reported-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Miklos Szeredi <mszeredi@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org> Cc: Daniel Borkmann <daniel@iogearbox.net> Cc: David S. Miller <davem@davemloft.net> Cc: Eric Dumazet <edumazet@google.com> Reported-by: Minmin chen <chenmingmin@huawei.com> Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com> Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Michal Kubecek reports that conntrack gc is responsible for frequent
wakeups (every 125ms) on idle systems.
On busy systems, timed out entries are evicted during lookup.
The gc worker is only needed to remove entries after system becomes idle
after a busy period.
To resolve this, always scan the entire table.
If the scan is taking too long, reschedule so other work_structs can run
and resume from next bucket.
After a completed scan, wait for 2 minutes before the next cycle.
Heuristics for faster re-schedule are removed.
GC_SCAN_INTERVAL could be exposed as a sysctl in the future to allow
tuning this as-needed or even turn the gc worker off.
Reported-by: Michal Kubecek <mkubecek@suse.cz> Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When the component level pin control functions were added they for some
no longer obvious reason handled adding prefixing of widget names. This
meant that when the lack of prefix handling in the DAPM level pin
operations was fixed by ae4fc532244b3bb4d (ASoC: dapm: use component
prefix when checking widget names) the one device using the component
level API ended up with the prefix being applied twice, causing all
lookups to fail.
Fix this by removing the redundant prefixing from the component code,
which has the nice side effect of also making that code much simpler.
Reported-by: Richard Fitzgerald <rf@opensource.cirrus.com> Signed-off-by: Mark Brown <broonie@kernel.org> Tested-by: Lucas Tanure <tanureal@opensource.cirrus.com> Link: https://lore.kernel.org/r/20210726194123.54585-1-broonie@kernel.org Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Jiri Olsa reported a bug ([1]) in kernel where cgroup local
storage pointer may be NULL in bpf_get_local_storage() helper.
There are two issues uncovered by this bug:
(1). kprobe or tracepoint prog incorrectly sets cgroup local storage
before prog run,
(2). due to change from preempt_disable to migrate_disable,
preemption is possible and percpu storage might be overwritten
by other tasks.
This issue (1) is fixed in [2]. This patch tried to address issue (2).
The following shows how things can go wrong:
task 1: bpf_cgroup_storage_set() for percpu local storage
preemption happens
task 2: bpf_cgroup_storage_set() for percpu local storage
preemption happens
task 1: run bpf program
task 1 will effectively use the percpu local storage setting by task 2
which will be either NULL or incorrect ones.
Instead of just one common local storage per cpu, this patch fixed
the issue by permitting 8 local storages per cpu and each local
storage is identified by a task_struct pointer. This way, we
allow at most 8 nested preemption between bpf_cgroup_storage_set()
and bpf_cgroup_storage_unset(). The percpu local storage slot
is released (calling bpf_cgroup_storage_unset()) by the same task
after bpf program finished running.
bpf_test_run() is also fixed to use the new bpf_cgroup_storage_set()
interface.
The patch is tested on top of [2] with reproducer in [1].
Without this patch, kernel will emit error in 2-3 minutes.
With this patch, after one hour, still no error.
Commit 457f44363a88 ("bpf: Implement BPF ring buffer and verifier support
for it") extended check_map_func_compatibility() by enforcing map -> helper
function match, but not helper -> map type match.
Due to this all of the bpf_ringbuf_*() helper functions could be used with
a wrong map type such as array or hash map, leading to invalid access due
to type confusion.
Also, both BPF_FUNC_ringbuf_{submit,discard} have ARG_PTR_TO_ALLOC_MEM as
argument and not a BPF map. Therefore, their check_map_func_compatibility()
presence is incorrect since it's only for map type checking.
Fixes: 457f44363a88 ("bpf: Implement BPF ring buffer and verifier support for it") Reported-by: Ryota Shiga (Flatt Security) Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If an SQPOLL based ring is newly created and an application issues an
io_uring_enter(2) system call on it, then we can return a spurious
-EOWNERDEAD error. This happens because there's nothing to submit, and
if the caller doesn't specify any other action, the initial error
assignment of -EOWNERDEAD never gets overwritten. This causes us to
return it directly, even if it isn't valid.
Move the error assignment into the actual failure case instead.
Cc: stable@vger.kernel.org Fixes: d9d05217cb69 ("io_uring: stop SQPOLL submit on creator's death") Reported-by: Sherlock Holo sherlockya@gmail.com Link: https://github.com/axboe/liburing/issues/413 Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Pavel Begunkov <asml.silence@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
We currently check for ret != 0 to indicate error, but '1' is a valid
return and just indicates that the allocation succeeded with a wrap.
Correct the check to be for < 0, like it was before the xarray
conversion.
We've had CONFIG_MANDATORY_FILE_LOCKING since 2015 and a lot of distros
have disabled it. Warn the stragglers that still use "-o mand" that
we'll be dropping support for that mount option.
Cc: stable@vger.kernel.org Signed-off-by: Jeff Layton <jlayton@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
We've noticed occasional OOM killing when memory.low settings are in
effect for cgroups. This is unexpected and undesirable as memory.low is
supposed to express non-OOMing memory priorities between cgroups.
The reason for this is proportional memory.low reclaim. When cgroups
are below their memory.low threshold, reclaim passes them over in the
first round, and then retries if it couldn't find pages anywhere else.
But when cgroups are slightly above their memory.low setting, page scan
force is scaled down and diminished in proportion to the overage, to the
point where it can cause reclaim to fail as well - only in that case we
currently don't retry, and instead trigger OOM.
To fix this, hook proportional reclaim into the same retry logic we have
in place for when cgroups are skipped entirely. This way if reclaim
fails and some cgroups were scanned with diminished pressure, we'll try
another full-force cycle before giving up and OOMing.
[akpm@linux-foundation.org: coding-style fixes]
Link: https://lkml.kernel.org/r/20210817180506.220056-1-hannes@cmpxchg.org Fixes: 9783aa9917f8 ("mm, memcg: proportional memory.{low,min} reclaim") Signed-off-by: Johannes Weiner <hannes@cmpxchg.org> Reported-by: Leon Yang <lnyng@fb.com> Reviewed-by: Rik van Riel <riel@surriel.com> Reviewed-by: Shakeel Butt <shakeelb@google.com> Acked-by: Roman Gushchin <guro@fb.com> Acked-by: Chris Down <chris@chrisdown.name> Acked-by: Michal Hocko <mhocko@suse.com> Cc: <stable@vger.kernel.org> [5.4+] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The commit 2e6b836312a4 ("ASoC: intel: atom: Fix reference to PCM
buffer address") changed the reference of PCM buffer address to
substream->runtime->dma_addr as the buffer address may change
dynamically. However, I forgot that the dma_addr field is still not
set up for the CONTINUOUS buffer type (that this driver uses) yet in
5.14 and earlier kernels, and it resulted in garbage I/O. The problem
will be fixed in 5.15, but we need to address it quickly for now.
The fix is to deduce the address again from the DMA pointer with
virt_to_phys(), but from the right one, substream->runtime->dma_area.
The Renoir XHCI controller apparently doesn't resume reliably with the
standard D3hot-to-D0 delay. Increase it to 20ms.
[Alex: I talked to the AMD USB hardware team and the AMD Windows team and
they are not aware of any HW errata or specific issues. The HW works fine
in Windows. I was told Windows uses a rather generous default delay of
100ms for PCI state transitions.]
Link: https://lore.kernel.org/r/20210722025858.220064-1-alexander.deucher@amd.com Signed-off-by: Marcin Bachry <hegel666@gmail.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Cc: stable@vger.kernel.org Cc: Mario Limonciello <mario.limonciello@amd.com> Cc: Prike Liang <prike.liang@amd.com> Cc: Shyam Sundar S K <shyam-sundar.s-k@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The struct pci_dev uses reference counting but zPCI assumed erroneously
that the last reference would always be the local reference after
calling pci_stop_and_remove_bus_device(). This is usually the case but
not how reference counting works and thus inherently fragile.
In fact one case where this causes a NULL pointer dereference when on an
SRIOV device the function 0 was hot unplugged before another function of
the same multi-function device. In this case the second function's
pdev->sriov->dev reference keeps the struct pci_dev of function 0 alive
even after the unplug. This bug was previously hidden by the fact that
we were leaking the struct pci_dev which in turn means that it always
outlived the struct zpci_dev. This was fixed in commit 0b13525c20fe
("s390/pci: fix leak of PCI device structure") exposing the broken
behavior.
Fix this by accounting for the long living reference a struct pci_dev
has to its underlying struct zpci_dev via the zbus->function[] array and
only release that in pcibios_release_device() ensuring that the struct
pci_dev is not left with a dangling reference. This is a minimal fix in
the future it would probably better to use fine grained reference
counting for struct zpci_dev.
Cross-rename lacks a check when that would prevent exchanging a
directory and subvolume from different parent subvolume. This causes
data inconsistencies and is caught before commit by tree-checker,
turning the filesystem to read-only.
Calling the renameat2 with RENAME_EXCHANGE flags like
The corrupted data will not be written, and filesystem can be unmounted
and mounted again (all changes since the last commit will be lost).
Add the missing check for new_ino so that all non-subvolumes must reside
under the same parent subvolume. There's an exception allowing to
exchange two subvolumes from any parents as the directory representing a
subvolume is only a logical link and does not have any other structures
related to the parent subvolume, unlike files, directories etc, that
are always in the inode namespace of the parent subvolume.
Fixes: cdd1fedf8261 ("btrfs: add support for RENAME_EXCHANGE and RENAME_WHITEOUT") CC: stable@vger.kernel.org # 4.7+ Reviewed-by: Nikolay Borisov <nborisov@suse.com> Signed-off-by: NeilBrown <neilb@suse.de> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The controller doesn't seem to pick-up on clock changes, so set the
SDHCI_QUIRK_CAP_CLOCK_BASE_BROKEN flag to query the clock frequency
directly from the clock.
Fixes: f84e411c85be ("mmc: sdhci-iproc: Add support for emmc2 of the BCM2711") Signed-off-by: Nicolas Saenz Julienne <nsaenz@kernel.org> Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/1628334401-6577-6-git-send-email-stefan.wahren@i2se.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
There is a known bug on BCM2711's SDHCI core integration where the
controller will hang when the difference between the core clock and the
bus clock is too great. Specifically this can be reproduced under the
following conditions:
- No SD card plugged in, polling thread is running, probing cards at
100 kHz.
- BCM2711's core clock configured at 500MHz or more.
So set 200 kHz as the minimum clock frequency available for that board.
For more information on the issue see this:
https://lore.kernel.org/linux-mmc/20210322185816.27582-1-nsaenz@kernel.org/T/#m11f2783a09b581da6b8a15f302625b43a6ecdeca
Fixes: f84e411c85be ("mmc: sdhci-iproc: Add support for emmc2 of the BCM2711") Signed-off-by: Nicolas Saenz Julienne <nsaenz@kernel.org> Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/1628334401-6577-5-git-send-email-stefan.wahren@i2se.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The 2021-model XPS 15 appears to use the same 4-speakers-on-ALC289 audio
setup as the Precision models, so requires the same quirk to enable woofer
output. Tested on my own 9510.
The error handling code in tpci200_register does not free interface_regs
allocated by ioremap and the current version of error handling code is
problematic.
Fix this by refactoring the error handling code and free interface_regs
when necessary.
Fixes: 43986798fd50 ("ipack: add error handling for ioremap_nocache") Cc: stable@vger.kernel.org Reported-by: Dongliang Mu <mudongliangabcd@gmail.com> Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com> Link: https://lore.kernel.org/r/20210810100323.3938492-2-mudongliangabcd@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The function tpci200_register called by tpci200_install and
tpci200_unregister called by tpci200_uninstall are in pair. However,
tpci200_unregister has some cleanup operations not in the
tpci200_register. So the error handling code of tpci200_pci_probe has
many different double free issues.
Fix this problem by moving those cleanup operations out of
tpci200_unregister, into tpci200_pci_remove and reverting
the previous commit 9272e5d0028d ("ipack/carriers/tpci200:
Fix a double free in tpci200_pci_probe").
Fixes: 9272e5d0028d ("ipack/carriers/tpci200: Fix a double free in tpci200_pci_probe") Cc: stable@vger.kernel.org Reported-by: Dongliang Mu <mudongliangabcd@gmail.com> Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com> Link: https://lore.kernel.org/r/20210810100323.3938492-1-mudongliangabcd@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
During suspend/resume NGD remote instance is power cycled along
with remotely controlled bam dma engine.
So Reset the dma configuration during this suspend resume path
so that we are not dealing with any stale dma setup.
Without this transactions timeout after first suspend resume path.
In some usecases transaction ids are dynamically allocated inside
the controller driver after sending the messages which have generic
acknowledge responses. So check for this before refcounting pm_runtime.
Without this we would end up imbalancing runtime pm count by
doing pm_runtime_put() in both slim_do_transfer() and slim_msg_response()
for a single pm_runtime_get() in slim_do_transfer()
As tid is unsigned its hard to figure out if the tid is valid or
invalid. So Start the transaction ids from 1 instead of zero
so that we could differentiate between a valid tid and invalid tids
This is useful in cases where controller would add a tid for controller
specific transfers.
The problem was the "trace(read_max,count)" where the "count" should be
"$count" as "onmax()" only handles variables (although it really should be
able to figure out that "count" is a field of sys_enter_read). But there's
a path that does not find the variable and ends up passing a NULL for the
event, which ends up getting passed to "strcmp()".
Add a check for NULL to return and error on the command with:
The original code in the cap_put_caller() function does not
handle correctly the positive values returned from the passed
function for multiple iterations. It means that the change
notifications may be lost.
As GDSCs are registered and found to be already enabled gdsc_init()
ensures that 1) the kernel state matches the hardware state, and 2)
votable GDSCs are properly enabled from this master as well.
But as the (optional) supply regulator is enabled deep into
gdsc_toggle_logic(), which is only executed for votable GDSCs, the
kernel's state of the regulator might not match the hardware. The
regulator might be automatically turned off if no other users are
present or the next call to gdsc_disable() would cause an unbalanced
regulator_disable().
Given that the votable case deals with an already enabled GDSC, most of
gdsc_enable() and gdsc_toggle_logic() can be skipped. Reduce it to just
clearing the SW_COLLAPSE_MASK and enabling hardware control to simply
call regulator_enable() in both cases.
The enablement of hardware control seems to be an independent property
from the GDSC being enabled, so this is moved outside that conditional
segment.
Lastly, as the propagation of ALWAYS_ON to GENPD_FLAG_ALWAYS_ON needs to
happen regardless of the initial state this is grouped together with the
other sc->pd updates at the end of the function.
The earlycon depends on the bootloader setup UART clocks being retained.
There're actually two uart clocks (ipg, per) on MX6QDL,
but the 'Fixes' commit change to register only one which means
another clock may be disabled during booting phase
and result in the earlycon unwork.
Cc: stable@vger.kernel.org # v5.10+ Fixes: 379c9a24cc23 ("clk: imx: Fix reparenting of UARTs not associated with stdout") Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com> Link: https://lore.kernel.org/r/20210702085438.1988087-1-aisheng.dong@nxp.com Reviewed-by: Abel Vesa <abel.vesa@nxp.com> Signed-off-by: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Whenever SDHC run at clock rate 50MHZ or below, the hardware data
timeout value will be 21.47secs, which is approx. 22secs and we have
a current software timeout value as 10secs. We have to set software
timeout value more than the hardware data timeout value to avioid seeing
the below register dumps.
If the card has not been power cycled, it may still be using 1.8V
signaling. This situation is detected in mmc_sd_init_card function and
should be handled in mmci stm32 variant. The host->pwr_reg variable is
also correctly protected with spin locks.
When a Data CRC interrupt is received, the driver disables the DMA, then
sends the stop/abort command and then waits for Data Transfer Over.
However, sometimes, when a data CRC error is received in the middle of a
multi-block write transfer, the Data Transfer Over interrupt is never
received, and the driver hangs and never completes the request.
The driver sets the BMOD.SWR bit (SDMMC_IDMAC_SWRESET) when stopping the
DMA, but according to the manual CMD.STOP_ABORT_CMD should be programmed
"before assertion of SWR". Do these operations in the recommended
order. With this change the Data Transfer Over is always received
correctly in my tests.
Cited commit added a check to make sure 'action' is not NULL, but
'action' is already dereferenced before the check, when calling
flow_offload_has_one_action().
Therefore, the check does not make any sense and results in a smatch
warning:
include/net/flow_offload.h:322 flow_action_mixed_hw_stats_check() warn:
variable dereferenced before check 'action' (see line 319)
Fix by reverting this commit.
Cc: gushengxian <gushengxian@yulong.com> Fixes: 9ea3e52c5bc8 ("flow_offload: action should not be NULL when it is referenced") Signed-off-by: Ido Schimmel <idosch@nvidia.com> Acked-by: Jamal Hadi Salim <jhs@mojatatu.com> Link: https://lore.kernel.org/r/20210819105842.1315705-1-idosch@idosch.org Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Make changes to MAC address dependent on the response of PF.
Disallow changes to HW MAC address and MAC filter from untrusted
VF, thanks to that ping is not lost if VF tries to change MAC.
Add a new field in iavf_mac_filter, to indicate whether there
was response from PF for given filter. Based on this field pass
or discard the filter.
If untrusted VF tried to change it's address, it's not changed.
Still filter was changed, because of that ping couldn't go through.
Fixes: c5c922b3e09b ("iavf: fix MAC address setting for VFs when filter is rejected") Signed-off-by: Przemyslaw Patynowski <przemyslawx.patynowski@intel.com> Signed-off-by: Sylwester Dziedziuch <sylwesterx.dziedziuch@intel.com> Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com> Tested-by: Gurucharan G <Gurucharanx.g@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Without this patch, ATR does not work. Receive/transmit uses queue
selection based on SW DCB hashing method.
If traffic classes are not configured for PF, then use
netdev_pick_tx function for selecting queue for packet transmission.
Instead of calling i40e_swdcb_skb_tx_hash, call netdev_pick_tx,
which ensures that packet is transmitted/received from CPU that is
running the application.
Reproduction steps:
1. Load i40e driver
2. Map each MSI interrupt of i40e port for each CPU
3. Disable ntuple, enable ATR i.e.:
ethtool -K $interface ntuple off
ethtool --set-priv-flags $interface flow-director-atr
4. Run application that is generating traffic and is bound to a
single CPU, i.e.:
taskset -c 9 netperf -H 1.1.1.1 -t TCP_RR -l 10
5. Observe behavior:
Application's traffic should be restricted to the CPU provided in
taskset.
Fixes: 89ec1f0886c1 ("i40e: Fix queue-to-TC mapping on Tx") Signed-off-by: Przemyslaw Patynowski <przemyslawx.patynowski@intel.com> Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com> Tested-by: Dave Switzer <david.switzer@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / thirdparty / kernel / stable.git / log
