In preparation for the objtool klp diff subcommand, broaden the
elf_create_symbol() interface to give callers more control and reduce
duplication of some subtle setup logic.
While at it, make elf_create_symbol() and elf_create_section_symbol()
global so sections can be created by the upcoming klp diff code.
Acked-by: Petr Mladek <pmladek@suse.com> Tested-by: Joe Lawrence <joe.lawrence@redhat.com> Signed-off-by: Josh Poimboeuf <jpoimboe@kernel.org>
The add_jump_destinations() logic is a bit weird and convoluted after
being incrementally tweaked over the years. Refactor it to hopefully be
more logical and straightforward.
Acked-by: Petr Mladek <pmladek@suse.com> Tested-by: Joe Lawrence <joe.lawrence@redhat.com> Signed-off-by: Josh Poimboeuf <jpoimboe@kernel.org>
The --backup option was removed with the following commit:
aa8b3e64fd39 ("objtool: Create backup on error and print args")
... which tied the backup functionality to --verbose, and only for
warnings/errors.
It's a bit inelegant and out of scope to tie that to --verbose.
Bring back the old --backup option, but with the new behavior: only on
warnings/errors, and print the args to make it easier to recreate.
Suggested-by: Peter Zijlstra <peterz@infradead.org> Acked-by: Petr Mladek <pmladek@suse.com> Tested-by: Joe Lawrence <joe.lawrence@redhat.com> Signed-off-by: Josh Poimboeuf <jpoimboe@kernel.org>
The objtool --Werror option name is stylistically inconsistent: halfway
between GCC's single-dash capitalized -Werror and objtool's double-dash
--lowercase convention, making it unnecessarily hard to remember.
Make the 'W' lower case (--werror) for consistency with objtool's other
options.
Acked-by: Petr Mladek <pmladek@suse.com> Tested-by: Joe Lawrence <joe.lawrence@redhat.com> Signed-off-by: Josh Poimboeuf <jpoimboe@kernel.org>
objtool: Avoid emptying lists for duplicate sections
When a to-be-created section already exists, there's no point in
emptying the various lists if their respective sections already exist.
In fact it's better to leave them intact as they might get used later.
Acked-by: Petr Mladek <pmladek@suse.com> Tested-by: Joe Lawrence <joe.lawrence@redhat.com> Signed-off-by: Josh Poimboeuf <jpoimboe@kernel.org>
In preparation for the objtool klp diff subcommand, introduce a flag to
identify __pfx_*() and __cfi_*() functions in advance so they don't need
to be manually identified every time a check is needed.
Acked-by: Petr Mladek <pmladek@suse.com> Tested-by: Joe Lawrence <joe.lawrence@redhat.com> Signed-off-by: Josh Poimboeuf <jpoimboe@kernel.org>
objtool: Fix weak symbol hole detection for .cold functions
When ignore_unreachable_insn() looks for weak function holes which jump
to their .cold functions, it assumes the parent function comes before
the corresponding .cold function in the symbol table. That's not
necessarily the case with -ffunction-sections.
Mark all the holes beforehand (including .cold functions) so the
ordering of the discovery doesn't matter.
Acked-by: Petr Mladek <pmladek@suse.com> Tested-by: Joe Lawrence <joe.lawrence@redhat.com> Signed-off-by: Josh Poimboeuf <jpoimboe@kernel.org>
objtool: Convert elf iterator macros to use 'struct elf'
'struct objtool_file' is specific to the check code and doesn't belong
in the elf code which is supposed to be objtool_file-agnostic. Convert
the elf iterator macros to use 'struct elf' instead.
Acked-by: Petr Mladek <pmladek@suse.com> Tested-by: Joe Lawrence <joe.lawrence@redhat.com> Signed-off-by: Josh Poimboeuf <jpoimboe@kernel.org>
KBUILD_HOSTCFLAGS and KBUILD_HOSTLDFLAGS aren't defined when objtool is
built standalone. Also, the EXTRA_WARNINGS flags are rather arbitrary.
Make things simpler and more consistent by specifying compiler flags
explicitly and tweaking the warnings. Also make a few code tweaks to
make the new warnings happy.
Acked-by: Petr Mladek <pmladek@suse.com> Tested-by: Joe Lawrence <joe.lawrence@redhat.com> Signed-off-by: Josh Poimboeuf <jpoimboe@kernel.org>
objtool: Fix "unexpected end of section" warning for alternatives
Due to the short circuiting logic in next_insn_to_validate(), control
flow may silently transition from .altinstr_replacement to .text without
a corresponding nested call to validate_branch().
As a result the validate_branch() 'sec' variable doesn't get
reinitialized, which can trigger a confusing "unexpected end of section"
warning which blames .altinstr_replacement rather than the offending
fallthrough function.
Fix that by not caching the section. There's no point in doing that
anyway.
Acked-by: Petr Mladek <pmladek@suse.com> Tested-by: Joe Lawrence <joe.lawrence@redhat.com> Signed-off-by: Josh Poimboeuf <jpoimboe@kernel.org>
find_symbol_hole_containing() fails to find a symbol hole (aka stripped
weak symbol) if its section has no symbols before the hole. This breaks
weak symbol detection if -ffunction-sections is enabled.
Fix that by allowing the interval tree to contain section symbols, which
are always at offset zero for a given section.
Fixes a bunch of (-ffunction-sections) warnings like:
fixed the issue where overlapping symbols weren't getting sorted
properly in the symbol tree. Therefore the workaround to skip adding
empty symbols from the following commit
a2e38dffcd93 ("objtool: Don't add empty symbols to the rbtree")
is no longer needed.
Acked-by: Petr Mladek <pmladek@suse.com> Tested-by: Joe Lawrence <joe.lawrence@redhat.com> Signed-off-by: Josh Poimboeuf <jpoimboe@kernel.org>
Up to a certain point in objtool's execution, all errors are fatal and
return -1. When propagating such errors, just return -1 directly
instead of trying to propagate the original return code. This helps
make the code more compact and the behavior more explicit.
Acked-by: Petr Mladek <pmladek@suse.com> Tested-by: Joe Lawrence <joe.lawrence@redhat.com> Signed-off-by: Josh Poimboeuf <jpoimboe@kernel.org>
objtool: Fix broken error handling in read_symbols()
The free(sym) call in the read_symbols() error path is fundamentally
broken: 'sym' doesn't point to any allocated block. If triggered,
things would go from bad to worse.
Remove the free() and simplify the error paths. Freeing memory isn't
necessary here anyway, these are fatal errors which lead to an immediate
exit().
Acked-by: Petr Mladek <pmladek@suse.com> Tested-by: Joe Lawrence <joe.lawrence@redhat.com> Signed-off-by: Josh Poimboeuf <jpoimboe@kernel.org>
objtool: Make find_symbol_containing() less arbitrary
In the rare case of overlapping symbols, find_symbol_containing() just
returns the first one it finds. Make it slightly less arbitrary by
returning the smallest symbol with size > 0.
Acked-by: Petr Mladek <pmladek@suse.com> Tested-by: Joe Lawrence <joe.lawrence@redhat.com> Signed-off-by: Josh Poimboeuf <jpoimboe@kernel.org>
The INT3 call emulation selftest is a bit fragile as it relies on the
compiler not inserting any extra instructions before the
int3_selftest_ip() definition.
Also, the int3_selftest_ip() symbol overlaps with the int3_selftest
symbol(), which can confuse objtool.
Fix those issues by slightly reworking the functionality and moving
int3_selftest_ip() to a separate asm function. While at it, improve the
naming.
Acked-by: Petr Mladek <pmladek@suse.com> Tested-by: Joe Lawrence <joe.lawrence@redhat.com> Signed-off-by: Josh Poimboeuf <jpoimboe@kernel.org>
In preparation for klp-build livepatch module creation tooling,
suppress warnings for unresolved references to linker-generated
__start_* and __stop_* section bounds symbols.
These symbols are expected to be undefined when modpost runs, as they're
created later by the linker.
Cc: Masahiro Yamada <masahiroy@kernel.org> Acked-by: Petr Mladek <pmladek@suse.com> Tested-by: Joe Lawrence <joe.lawrence@redhat.com> Signed-off-by: Josh Poimboeuf <jpoimboe@kernel.org>
kbuild: Remove 'kmod_' prefix from __KBUILD_MODNAME
In preparation for the objtool klp diff subcommand, remove the arbitrary
'kmod_' prefix from __KBUILD_MODNAME and instead add it explicitly in
the __initcall_id() macro.
This change supports the standardization of "unique" symbol naming by
ensuring the non-unique portion of the name comes before the unique
part. That will enable objtool to properly correlate symbols across
builds.
Cc: Masahiro Yamada <masahiroy@kernel.org> Acked-by: Petr Mladek <pmladek@suse.com> Tested-by: Joe Lawrence <joe.lawrence@redhat.com> Signed-off-by: Josh Poimboeuf <jpoimboe@kernel.org>
In preparation for the objtool klp diff subcommand, replace the custom
unique symbol name generation in ELFNOTE() with __UNIQUE_ID().
This standardizes the naming format for all "unique" symbols, which will
allow objtool to properly correlate them. Note this also removes the
"one ELF note per line" limitation.
Acked-by: Petr Mladek <pmladek@suse.com> Tested-by: Joe Lawrence <joe.lawrence@redhat.com> Signed-off-by: Josh Poimboeuf <jpoimboe@kernel.org>
In preparation for the objtool klp diff subcommand, add an underscore
between the name and the counter. This will make it possible for
objtool to distinguish between the non-unique and unique parts of the
symbol name so it can properly correlate the symbols.
Acked-by: Petr Mladek <pmladek@suse.com> Tested-by: Joe Lawrence <joe.lawrence@redhat.com> Signed-off-by: Josh Poimboeuf <jpoimboe@kernel.org>
Since commit 877b145f0f47 ("x86/kprobes: Move trampoline code into
RODATA"), the optprobe template code is no longer analyzed by objtool so
it doesn't need to be ignored.
Acked-by: Petr Mladek <pmladek@suse.com> Tested-by: Joe Lawrence <joe.lawrence@redhat.com> Signed-off-by: Josh Poimboeuf <jpoimboe@kernel.org>
vmlinux.lds: Unify TEXT_MAIN, DATA_MAIN, and related macros
TEXT_MAIN, DATA_MAIN and friends are defined differently depending on
whether certain config options enable -ffunction-sections and/or
-fdata-sections.
There's no technical reason for that beyond voodoo coding. Keeping the
separate implementations adds unnecessary complexity, fragments the
logic, and increases the risk of subtle bugs.
Unify the macros by using the same input section patterns across all
configs.
This is a prerequisite for the upcoming livepatch klp-build tooling
which will manually enable -ffunction-sections and -fdata-sections via
KCFLAGS.
Cc: Heiko Carstens <hca@linux.ibm.com> Cc: Vasily Gorbik <gor@linux.ibm.com> Cc: Alexander Gordeev <agordeev@linux.ibm.com> Acked-by: Petr Mladek <pmladek@suse.com> Tested-by: Joe Lawrence <joe.lawrence@redhat.com> Signed-off-by: Josh Poimboeuf <jpoimboe@kernel.org>
s390/vmlinux.lds.S: Prevent thunk functions from getting placed with normal text
The s390 indirect thunks are placed in the .text.__s390_indirect_jump_*
sections.
Certain config options which enable -ffunction-sections have a custom
version of the TEXT_TEXT macro:
.text.[0-9a-zA-Z_]*
That unintentionally matches the thunk sections, causing them to get
grouped with normal text rather than being handled by their intended
rule later in the script:
*(.text.*_indirect_*)
Fix that by adding another period to the thunk section names, following
the kernel's general convention for distinguishing code-generated text
sections from compiler-generated ones.
Cc: Vasily Gorbik <gor@linux.ibm.com> Cc: Alexander Gordeev <agordeev@linux.ibm.com> Acked-by: Heiko Carstens <hca@linux.ibm.com> Acked-by: Petr Mladek <pmladek@suse.com> Tested-by: Joe Lawrence <joe.lawrence@redhat.com> Signed-off-by: Josh Poimboeuf <jpoimboe@kernel.org>
The objtool command line 'objtool --hacks=jump_label foo.o' on its own
should be expected to rewrite jump labels to NOPs. This means the
add_special_section_alts() code path needs to run when only this option
is provided.
This is mainly relevant in certain debugging situations, but could
potentially also fix kernel builds in which objtool is run with
--hacks=jump_label but without --orc, --stackval, --uaccess, or
--hacks=noinstr.
Fixes: de6fbcedf5ab ("objtool: Read special sections with alts only when specific options are selected") Signed-off-by: Dylan Hatch <dylanbhatch@google.com> Signed-off-by: Josh Poimboeuf <jpoimboe@kernel.org>
scripts/faddr2line: Fix "Argument list too long" error
The run_readelf() function reads the entire output of readelf into a
single shell variable. For large object files with extensive debug
information, the size of this variable can exceed the system's
command-line argument length limit.
When this variable is subsequently passed to sed via `echo "${out}"`, it
triggers an "Argument list too long" error, causing the script to fail.
Fix this by redirecting the output of readelf to a temporary file
instead of a variable. The sed commands are then modified to read from
this file, avoiding the argument length limitation entirely.
scripts/faddr2line: Use /usr/bin/env bash for portability
The shebang `#!/bin/bash` assumes a fixed path for the bash interpreter.
This path does not exist on some systems, such as NixOS, causing the
script to fail.
Replace `/bin/bash` with the more portable `#!/usr/bin/env bash`.
John Wang [Fri, 28 Mar 2025 07:38:02 +0000 (15:38 +0800)]
scripts/faddr2line: Set LANG=C to enforce ASCII output
Force tools like readelf to use the POSIX/C locale by exporting LANG=C
This ensures ASCII-only output and avoids locale-specific
characters(e.g., UTF-8 symbols or translated strings), which could
break text processing utilities like sed in the script
Signed-off-by: John Wang <wangzq.jn@gmail.com> Signed-off-by: Josh Poimboeuf <jpoimboe@kernel.org>
Josh Poimboeuf [Mon, 3 Mar 2025 01:01:42 +0000 (17:01 -0800)]
tools build: Fix fixdep dependencies
The tools version of fixdep has broken dependencies. It doesn't get
rebuilt if the host compiler or headers change.
Build fixdep with the tools kbuild infrastructure, so fixdep runs on
itself. Due to the recursive dependency, its dependency file is
incomplete the very first time it gets built. In that case build it a
second time to achieve fixdep inception.
Reported-by: Arthur Marsh <arthur.marsh@internode.on.net> Signed-off-by: Josh Poimboeuf <jpoimboe@kernel.org>
Linus Torvalds [Sun, 12 Oct 2025 20:27:56 +0000 (13:27 -0700)]
Merge tag 'i2c-for-6.18-rc1-hotfix' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fix from Wolfram Sang:
"One revert because of a regression in the I2C core which has sadly not
showed up during its time in -next"
* tag 'i2c-for-6.18-rc1-hotfix' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
Revert "i2c: boardinfo: Annotate code used in init phase only"
Linus Torvalds [Sun, 12 Oct 2025 15:45:52 +0000 (08:45 -0700)]
Merge tag 'irq_urgent_for_v6.18_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fixes from Borislav Petkov:
- Skip interrupt ID 0 in sifive-plic during suspend/resume because
ID 0 is reserved and accessing reserved register space could result
in undefined behavior
- Fix a function's retval check in aspeed-scu-ic
* tag 'irq_urgent_for_v6.18_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/sifive-plic: Avoid interrupt ID 0 handling during suspend/resume
irqchip/aspeed-scu-ic: Fix an IS_ERR() vs NULL check
Linus Torvalds [Sat, 11 Oct 2025 23:06:04 +0000 (16:06 -0700)]
Merge tag 'trace-v6.18-3' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace
Pull tracing fixes from Steven Rostedt:
"The previous fix to trace_marker required updating trace_marker_raw as
well. The difference between trace_marker_raw from trace_marker is
that the raw version is for applications to write binary structures
directly into the ring buffer instead of writing ASCII strings. This
is for applications that will read the raw data from the ring buffer
and get the data structures directly. It's a bit quicker than using
the ASCII version.
Unfortunately, it appears that our test suite has several tests that
test writes to the trace_marker file, but lacks any tests to the
trace_marker_raw file (this needs to be remedied). Two issues came
about the update to the trace_marker_raw file that syzbot found:
- Fix tracing_mark_raw_write() to use per CPU buffer
The fix to use the per CPU buffer to copy from user space was
needed for both the trace_maker and trace_maker_raw file.
The fix for reading from user space into per CPU buffers properly
fixed the trace_marker write function, but the trace_marker_raw
file wasn't fixed properly. The user space data was correctly
written into the per CPU buffer, but the code that wrote into the
ring buffer still used the user space pointer and not the per CPU
buffer that had the user space data already written.
- Stop the fortify string warning from writing into trace_marker_raw
After converting the copy_from_user_nofault() into a memcpy(),
another issue appeared. As writes to the trace_marker_raw expects
binary data, the first entry is a 4 byte identifier. The entry
structure is defined as:
struct {
struct trace_entry ent;
int id;
char buf[];
};
The size of this structure is reserved on the ring buffer with:
size = sizeof(*entry) + cnt;
Then it is copied from the buffer into the ring buffer with:
memcpy(&entry->id, buf, cnt);
This use to be a copy_from_user_nofault(), but now converting it to
a memcpy() triggers the fortify-string code, and causes a warning.
The allocated space is actually more than what is copied, as the
cnt used also includes the entry->id portion. Allocating
sizeof(*entry) plus cnt is actually allocating 4 bytes more than
what is needed.
* tag 'trace-v6.18-3' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
tracing: Stop fortify-string from warning in tracing_mark_raw_write()
tracing: Fix tracing_mark_raw_write() to use buf and not ubuf
Linus Torvalds [Sat, 11 Oct 2025 22:47:12 +0000 (15:47 -0700)]
Merge tag 'kbuild-fixes-6.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/kbuild/linux
Pull Kbuild fixes from Nathan Chancellor:
- Fix UAPI types check in headers_check.pl
- Only enable -Werror for hostprogs with CONFIG_WERROR / W=e
- Ignore fsync() error when output of gen_init_cpio is a pipe
- Several little build fixes for recent modules.builtin.modinfo series
* tag 'kbuild-fixes-6.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/kbuild/linux:
kbuild: Use '--strip-unneeded-symbol' for removing module device table symbols
s390/vmlinux.lds.S: Move .vmlinux.info to end of allocatable sections
kbuild: Add '.rel.*' strip pattern for vmlinux
kbuild: Restore pattern to avoid stripping .rela.dyn from vmlinux
gen_init_cpio: Ignore fsync() returning EINVAL on pipes
scripts/Makefile.extrawarn: Respect CONFIG_WERROR / W=e for hostprogs
kbuild: uapi: Strip comments before size type check
Reported-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com> Closes: https://lore.kernel.org/r/29ec0082-4dd4-4120-acd2-44b35b4b9487@oss.qualcomm.com Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Linus Torvalds [Sat, 11 Oct 2025 18:56:47 +0000 (11:56 -0700)]
Merge tag 'rtc-6.18' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux
Pull RTC updates from Alexandre Belloni:
"This cycle, we have a new RTC driver, for the SpacemiT P1. The optee
driver gets alarm support. We also get a fix for a race condition that
was fairly rare unless while stress testing the alarms.
Subsystem:
- Fix race when setting alarm
- Ensure alarm irq is enabled when UIE is enabled
- remove unneeded 'fast_io' parameter in regmap_config
New driver:
- SpacemiT P1 RTC
Drivers:
- efi: Remove wakeup functionality
- optee: add alarms support
- s3c: Drop support for S3C2410
- zynqmp: Restore alarm functionality after kexec transition"
* tag 'rtc-6.18' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux: (29 commits)
rtc: interface: Ensure alarm irq is enabled when UIE is enabled
rtc: tps6586x: Fix initial enable_irq/disable_irq balance
rtc: cpcap: Fix initial enable_irq/disable_irq balance
rtc: isl12022: Fix initial enable_irq/disable_irq balance
rtc: interface: Fix long-standing race when setting alarm
rtc: pcf2127: fix watchdog interrupt mask on pcf2131
rtc: zynqmp: Restore alarm functionality after kexec transition
rtc: amlogic-a4: Optimize global variables
rtc: sd2405al: Add I2C address.
rtc: Kconfig: move symbols to proper section
rtc: optee: make optee_rtc_pm_ops static
rtc: optee: Fix error code in optee_rtc_read_alarm()
rtc: optee: fix error code in probe()
dt-bindings: rtc: Convert apm,xgene-rtc to DT schema
rtc: spacemit: support the SpacemiT P1 RTC
rtc: optee: add alarm related rtc ops to optee rtc driver
rtc: optee: remove unnecessary memory operations
rtc: optee: fix memory leak on driver removal
rtc: x1205: Fix Xicor X1205 vendor prefix
dt-bindings: rtc: Fix Xicor X1205 vendor prefix
...
Linus Torvalds [Sat, 11 Oct 2025 18:49:00 +0000 (11:49 -0700)]
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Fixes only in drivers (ufs, mvsas, qla2xxx, target) that came in just
before or during the merge window.
The most important one is the qla2xxx which reverts a conversion to
fix flexible array member warnings, that went up in this merge window
but which turned out on further testing to be causing data corruption"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: ufs: core: Include UTP error in INT_FATAL_ERRORS
scsi: ufs: sysfs: Make HID attributes visible
scsi: mvsas: Fix use-after-free bugs in mvs_work_queue
scsi: ufs: core: Fix PM QoS mutex initialization
scsi: ufs: core: Fix runtime suspend error deadlock
Revert "scsi: qla2xxx: Fix memcpy() field-spanning write issue"
scsi: target: target_core_configfs: Add length check to avoid buffer overflow
Linus Torvalds [Sat, 11 Oct 2025 18:19:16 +0000 (11:19 -0700)]
Merge tag 'x86_core_for_v6.18_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull more x86 updates from Borislav Petkov:
- Remove a bunch of asm implementing condition flags testing in KVM's
emulator in favor of int3_emulate_jcc() which is written in C
- Replace KVM fastops with C-based stubs which avoids problems with the
fastop infra related to latter not adhering to the C ABI due to their
special calling convention and, more importantly, bypassing compiler
control-flow integrity checking because they're written in asm
- Remove wrongly used static branches and other ugliness accumulated
over time in hyperv's hypercall implementation with a proper static
function call to the correct hypervisor call variant
- Add some fixes and modifications to allow running FRED-enabled
kernels in KVM even on non-FRED hardware
- Add kCFI improvements like validating indirect calls and prepare for
enabling kCFI with GCC. Add cmdline params documentation and other
code cleanups
- Use the single-byte 0xd6 insn as the official #UD single-byte
undefined opcode instruction as agreed upon by both x86 vendors
- Other smaller cleanups and touchups all over the place
* tag 'x86_core_for_v6.18_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (24 commits)
x86,retpoline: Optimize patch_retpoline()
x86,ibt: Use UDB instead of 0xEA
x86/cfi: Remove __noinitretpoline and __noretpoline
x86/cfi: Add "debug" option to "cfi=" bootparam
x86/cfi: Standardize on common "CFI:" prefix for CFI reports
x86/cfi: Document the "cfi=" bootparam options
x86/traps: Clarify KCFI instruction layout
compiler_types.h: Move __nocfi out of compiler-specific header
objtool: Validate kCFI calls
x86/fred: KVM: VMX: Always use FRED for IRQs when CONFIG_X86_FRED=y
x86/fred: Play nice with invoking asm_fred_entry_from_kvm() on non-FRED hardware
x86/fred: Install system vector handlers even if FRED isn't fully enabled
x86/hyperv: Use direct call to hypercall-page
x86/hyperv: Clean up hv_do_hypercall()
KVM: x86: Remove fastops
KVM: x86: Convert em_salc() to C
KVM: x86: Introduce EM_ASM_3WCL
KVM: x86: Introduce EM_ASM_1SRC2
KVM: x86: Introduce EM_ASM_2CL
KVM: x86: Introduce EM_ASM_2W
...
Linus Torvalds [Sat, 11 Oct 2025 17:51:14 +0000 (10:51 -0700)]
Merge tag 'x86_cleanups_for_v6.18_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 cleanups from Borislav Petkov:
- Simplify inline asm flag output operands now that the minimum
compiler version supports the =@ccCOND syntax
- Remove a bunch of AS_* Kconfig symbols which detect assembler support
for various instruction mnemonics now that the minimum assembler
version supports them all
- The usual cleanups all over the place
* tag 'x86_cleanups_for_v6.18_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/asm: Remove code depending on __GCC_ASM_FLAG_OUTPUTS__
x86/sgx: Use ENCLS mnemonic in <kernel/cpu/sgx/encls.h>
x86/mtrr: Remove license boilerplate text with bad FSF address
x86/asm: Use RDPKRU and WRPKRU mnemonics in <asm/special_insns.h>
x86/idle: Use MONITORX and MWAITX mnemonics in <asm/mwait.h>
x86/entry/fred: Push __KERNEL_CS directly
x86/kconfig: Remove CONFIG_AS_AVX512
crypto: x86 - Remove CONFIG_AS_VPCLMULQDQ
crypto: X86 - Remove CONFIG_AS_VAES
crypto: x86 - Remove CONFIG_AS_GFNI
x86/kconfig: Drop unused and needless config X86_64_SMP
Linus Torvalds [Sat, 11 Oct 2025 17:40:24 +0000 (10:40 -0700)]
Merge tag 'slab-for-6.18-rc1-hotfix' of git://git.kernel.org/pub/scm/linux/kernel/git/vbabka/slab
Pull slab fix from Vlastimil Babka:
"A NULL pointer deref hotfix"
* tag 'slab-for-6.18-rc1-hotfix' of git://git.kernel.org/pub/scm/linux/kernel/git/vbabka/slab:
slab: fix barn NULL pointer dereference on memoryless nodes
- Fix metadata_dst leak in __bpf_redirect_neigh_v{4,6}() (Daniel
Borkmann)
- Fix undefined behavior in {get,put}_unaligned_be32() (Eric Biggers)
- Use correct context to unpin bpf hash map with special types (KaFai
Wan)
* tag 'bpf-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf:
selftests/bpf: Add test for unpinning htab with internal timer struct
bpf: Avoid RCU context warning when unpinning htab with internal structs
xsk: Harden userspace-supplied xdp_desc validation
bpf: Fix metadata_dst leak __bpf_redirect_neigh_v{4,6}
libbpf: Fix undefined behavior in {get,put}_unaligned_be32()
bpf: Finish constification of 1st parameter of bpf_d_path()
Linus Torvalds [Sat, 11 Oct 2025 17:27:52 +0000 (10:27 -0700)]
Merge tag 'mm-nonmm-stable-2025-10-10-15-03' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull more updates from Andrew Morton:
"Just one series here - Mike Rappoport has taught KEXEC handover to
preserve vmalloc allocations across handover"
* tag 'mm-nonmm-stable-2025-10-10-15-03' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm:
lib/test_kho: use kho_preserve_vmalloc instead of storing addresses in fdt
kho: add support for preserving vmalloc allocations
kho: replace kho_preserve_phys() with kho_preserve_pages()
kho: check if kho is finalized in __kho_preserve_order()
MAINTAINERS, .mailmap: update Umang's email address
Linus Torvalds [Sat, 11 Oct 2025 17:14:55 +0000 (10:14 -0700)]
Merge tag 'mm-hotfixes-stable-2025-10-10-15-00' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull misc fixes from Andrew Morton:
"7 hotfixes. All 7 are cc:stable and all 7 are for MM.
All singletons, please see the changelogs for details"
* tag 'mm-hotfixes-stable-2025-10-10-15-00' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm:
mm: hugetlb: avoid soft lockup when mprotect to large memory area
fsnotify: pass correct offset to fsnotify_mmap_perm()
mm/ksm: fix flag-dropping behavior in ksm_madvise
mm/damon/vaddr: do not repeat pte_offset_map_lock() until success
mm/rmap: fix soft-dirty and uffd-wp bit loss when remapping zero-filled mTHP subpage to shared zeropage
mm/thp: fix MTE tag mismatch when replacing zero-filled subpages
memcg: skip cgroup_file_notify if spinning is not allowed
This is because fortify string sees that the size of entry->id is only 4
bytes, but it is writing more than that. But this is OK as the
dynamic_array is allocated to handle that copy.
The size allocated on the ring buffer was actually a bit too big:
size = sizeof(*entry) + cnt;
But cnt includes the 'id' and the buffer data, so adding cnt to the size
of *entry actually allocates too much on the ring buffer.
Vlastimil Babka [Sat, 11 Oct 2025 08:45:41 +0000 (10:45 +0200)]
slab: fix barn NULL pointer dereference on memoryless nodes
Phil reported a boot failure once sheaves become used in commits 59faa4da7cd4 ("maple_tree: use percpu sheaves for maple_node_cache") and 3accabda4da1 ("mm, vma: use percpu sheaves for vm_area_struct cache"):
Linus decoded the stacktrace to get_barn() and get_node() and determined
that kmem_cache->node[numa_mem_id()] is NULL.
The problem is due to a wrong assumption that memoryless nodes only
exist on systems with CONFIG_HAVE_MEMORYLESS_NODES, where numa_mem_id()
points to the nearest node that has memory. SLUB has been allocating its
kmem_cache_node structures only on nodes with memory and so it does with
struct node_barn.
For kmem_cache_node, get_partial_node() checks if get_node() result is
not NULL, which I assumed was for protection from a bogus node id passed
to kmalloc_node() but apparently it's also for systems where
numa_mem_id() (used when no specific node is given) might return a
memoryless node.
Fix the sheaves code the same way by checking the result of get_node()
and bailing out if it's NULL. Note that cpus on such memoryless nodes
will have degraded sheaves performance, which can be improved later,
preferably by making numa_mem_id() work properly on such systems.
Steven Rostedt [Sat, 11 Oct 2025 03:51:42 +0000 (23:51 -0400)]
tracing: Fix tracing_mark_raw_write() to use buf and not ubuf
The fix to use a per CPU buffer to read user space tested only the writes
to trace_marker. But it appears that the selftests are missing tests to
the trace_maker_raw file. The trace_maker_raw file is used by applications
that writes data structures and not strings into the file, and the tools
read the raw ring buffer to process the structures it writes.
The fix that reads the per CPU buffers passes the new per CPU buffer to
the trace_marker file writes, but the update to the trace_marker_raw write
read the data from user space into the per CPU buffer, but then still used
then passed the user space address to the function that records the data.
Pass in the per CPU buffer and not the user space address.
TODO: Add a test to better test trace_marker_raw.
Cc: stable@vger.kernel.org Cc: Masami Hiramatsu <mhiramat@kernel.org> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com> Cc: Andrew Morton <akpm@linux-foundation.org> Link: https://lore.kernel.org/20251011035243.386098147@kernel.org Fixes: 64cf7d058a00 ("tracing: Have trace_marker use per-cpu data to read user space") Reported-by: syzbot+9a2ede1643175f350105@syzkaller.appspotmail.com Closes: https://lore.kernel.org/all/68e973f5.050a0220.1186a4.0010.GAE@google.com/ Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
kbuild: Use '--strip-unneeded-symbol' for removing module device table symbols
After commit 5ab23c7923a1 ("modpost: Create modalias for builtin
modules"), relocatable RISC-V kernels with CONFIG_KASAN=y start failing
when attempting to strip the module device table symbols:
riscv64-linux-objcopy: not stripping symbol `__mod_device_table__kmod_irq_starfive_jh8100_intc__of__starfive_intc_irqchip_match_table' because it is named in a relocation
make[4]: *** [scripts/Makefile.vmlinux:97: vmlinux] Error 1
The relocation appears to come from .LASANLOC5 in .data.rel.local:
This section appears to come from GCC for including additional
information about global variables that may be protected by KASAN.
There appears to be no way to opt out of the generation of these symbols
through either a flag or attribute. Attempting to remove '.LASANLOC*'
with '--strip-symbol' results in the same error as above because these
symbols may refer to (thus have relocation between) each other.
Avoid this build breakage by switching to '--strip-unneeded-symbol' for
removing __mod_device_table__ symbols, as it will only remove the symbol
when there is no relocation pointing to it. While this may result in a
little more bloat in the symbol table in certain configurations, it is
not as bad as outright build failures.
Fixes: 5ab23c7923a1 ("modpost: Create modalias for builtin modules") Reported-by: Charles Mirabile <cmirabil@redhat.com> Closes: https://lore.kernel.org/20251007011637.2512413-1-cmirabil@redhat.com/ Suggested-by: Alexey Gladkov <legion@kernel.org> Tested-by: Nicolas Schier <nsc@kernel.org> Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Linus Torvalds [Fri, 10 Oct 2025 21:06:02 +0000 (14:06 -0700)]
Merge tag 'for-6.18/hpfs-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull hpfs updates from Mikulas Patocka:
- Avoid -Wflex-array-member-not-at-end warnings
- Replace simple_strtoul with kstrtoint
- Fix error code for new_inode() failure
* tag 'for-6.18/hpfs-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
fs/hpfs: Fix error code for new_inode() failure in mkdir/create/mknod/symlink
hpfs: Replace simple_strtoul with kstrtoint in hpfs_parse_param
fs: hpfs: Avoid multiple -Wflex-array-member-not-at-end warnings
amdkfd:
- Fix kfd process ref leak
- mmap write lock handling fix
- Fix comments in IOCTL
xe:
- Fix build with clang 16
- Fix handling of invalid configfs syntax usage and spell out the
expected syntax in the documentation
- Do not try late bind firmware when running as VF since it shouldn't
handle firmware loading
- Fix idle assertion for local BOs
- Fix uninitialized variable for late binding
- Do not require perfmon_capable to expose free memory at page
granularity. Handle it like other drm drivers do
- Fix lock handling on suspend error path
- Fix I2C controller resume after S3
v3d:
- fix fence locking"
* tag 'drm-next-2025-10-11-1' of https://gitlab.freedesktop.org/drm/kernel: (34 commits)
drm/amd/display: Incorrect Mirror Cositing
drm/amd/display: Enable Dynamic DTBCLK Switch
drm/amdgpu: Report individual reset error
drm/amdgpu: partially revert "revert to old status lock handling v3"
drm/amd/display: Fix unsafe uses of kernel mode FPU
drm/amd/pm: Disable VCN queue reset on SMU v13.0.6 due to regression
drm/amdgpu: Fix general protection fault in amdgpu_vm_bo_reset_state_machine
drm/amdgpu: Check swus/ds for switch state save
drm/amdkfd: Fix two comments in kfd_ioctl.h
drm/amd/pm: Avoid interface mismatch messaging
drm/amdgpu: Merge amdgpu_vm_set_pasid into amdgpu_vm_init
drm/amd/amdgpu: Fix the mes version that support inv_tlbs
drm/amd: Check whether secure display TA loaded successfully
drm/amdkfd: Fix mmap write lock not release
drm/amdkfd: Fix kfd process ref leaking when userptr unmapping
drm/amdgpu: Fix for GPU reset being blocked by KIQ I/O.
drm/amd/display: Disable scaling on DCE6 for now
drm/amd/display: Properly disable scaling on DCE6
drm/amd/display: Properly clear SCL_*_FILTER_CONTROL on DCE6
drm/amd/display: Add missing DCE6 SCL_HORZ_FILTER_INIT* SRIs
...
Linus Torvalds [Fri, 10 Oct 2025 20:59:38 +0000 (13:59 -0700)]
Merge tag 'drm-fixes-2025-10-11' of https://gitlab.freedesktop.org/drm/kernel
Pull drm fixes from Dave Airlie:
"Some fixes leftover from our fixes branch, just nouveau and vmwgfx:
nouveau:
- Return errno code from TTM move helper
vmwgfx:
- Fix null-ptr access in cursor code
- Fix UAF in validation
- Use correct iterator in validation"
* tag 'drm-fixes-2025-10-11' of https://gitlab.freedesktop.org/drm/kernel:
drm/nouveau: fix bad ret code in nouveau_bo_move_prep
drm/vmwgfx: Fix copy-paste typo in validation
drm/vmwgfx: Fix Use-after-free in validation
drm/vmwgfx: Fix a null-ptr access in the cursor snooper
Allow additional properties to enable devices attached to the bus.
Fixes warnings like these:
arch/arm/boot/dts/renesas/sh73a0-kzm9g.dtb: bus@fec10000 (renesas,bsc-sh73a0): Unevaluated properties are not allowed ('ethernet@10000000' was unexpected)
arch/arm/boot/dts/renesas/r8a73a4-ape6evm.dtb: bus@fec10000 (renesas,bsc-r8a73a4): Unevaluated properties are not allowed ('ethernet@8000000', 'flash@0' were unexpected)
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Node names are already and properly checked by the core schema. No need
to do it again.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
[robh: Also drop [A-F] in unit address] Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Linus Torvalds [Fri, 10 Oct 2025 18:30:19 +0000 (11:30 -0700)]
Merge tag 'ceph-for-6.18-rc1' of https://github.com/ceph/ceph-client
Pull ceph updates from Ilya Dryomov:
- some messenger improvements (Eric and Max)
- address an issue (also affected userspace) of incorrect permissions
being granted to users who have access to multiple different CephFS
instances within the same cluster (Kotresh)
- a bunch of assorted CephFS fixes (Slava)
* tag 'ceph-for-6.18-rc1' of https://github.com/ceph/ceph-client:
ceph: add bug tracking system info to MAINTAINERS
ceph: fix multifs mds auth caps issue
ceph: cleanup in ceph_alloc_readdir_reply_buffer()
ceph: fix potential NULL dereference issue in ceph_fill_trace()
libceph: add empty check to ceph_con_get_out_msg()
libceph: pass the message pointer instead of loading con->out_msg
libceph: make ceph_con_get_out_msg() return the message pointer
ceph: fix potential race condition on operations with CEPH_I_ODIRECT flag
ceph: refactor wake_up_bit() pattern of calling
ceph: fix potential race condition in ceph_ioctl_lazyio()
ceph: fix overflowed constant issue in ceph_do_objects_copy()
ceph: fix wrong sizeof argument issue in register_session()
ceph: add checking of wait_for_completion_killable() return value
ceph: make ceph_start_io_*() killable
libceph: Use HMAC-SHA256 library instead of crypto_shash
Linus Torvalds [Fri, 10 Oct 2025 18:23:57 +0000 (11:23 -0700)]
Merge tag 'v6.18-rc-part2-smb-client-fixes' of git://git.samba.org/sfrench/cifs-2.6
Pull more smb client updates from Steve French:
- fix i_size in fallocate
- two truncate fixes
- utime fix
- minor cleanups
- SMB1 fixes
- improve error check in read
- improve perf of copy file_range (copy_chunk)
* tag 'v6.18-rc-part2-smb-client-fixes' of git://git.samba.org/sfrench/cifs-2.6:
cifs: update internal version number
cifs: Add comments for DeletePending assignments in open functions
cifs: Add fallback code path for cifs_mkdir_setinfo()
cifs: Allow fallback code in smb_set_file_info() also for directories
cifs: Query EA $LXMOD in cifs_query_path_info() for WSL reparse points
smb: client: remove cfids_invalidation_worker
smb: client: remove redudant assignment in cifs_strict_fsync()
smb: client: fix race with fallocate(2) and AIO+DIO
smb: client: fix missing timestamp updates after utime(2)
smb: client: fix missing timestamp updates after ftruncate(2)
smb: client: fix missing timestamp updates with O_TRUNC
cifs: Fix copy_to_iter return value check
smb: client: batch SRV_COPYCHUNK entries to cut round trips
smb: client: Omit an if branch in smb2_find_smb_tcon()
smb: client: Return directly after a failed genlmsg_new() in cifs_swn_send_register_message()
smb: client: Use common code in cifs_do_create()
smb: client: Improve unlocking of a mutex in cifs_get_swn_reg()
smb: client: Return a status code only as a constant in cifs_spnego_key_instantiate()
smb: client: Use common code in cifs_lookup()
smb: client: Reduce the scopes for a few variables in two functions
Linus Torvalds [Fri, 10 Oct 2025 18:20:19 +0000 (11:20 -0700)]
Merge tag 'xtensa-20251010' of https://github.com/jcmvbkbc/linux-xtensa
Pull Xtensa updates from Max Filippov:
- minor cleanups
* tag 'xtensa-20251010' of https://github.com/jcmvbkbc/linux-xtensa:
xtensa: use HZ_PER_MHZ in platform_calibrate_ccount
xtensa: simdisk: add input size check in proc_write_simdisk
Linus Torvalds [Fri, 10 Oct 2025 17:37:13 +0000 (10:37 -0700)]
Merge tag 'block-6.18-20251009' of git://git.kernel.org/pub/scm/linux/kernel/git/axboe/linux
Pull block fixes from Jens Axboe:
- Don't include __GFP_NOWARN for loop worker allocation, as it already
uses GFP_NOWAIT which has __GFP_NOWARN set already
- Small series cleaning up the recent bio_iov_iter_get_pages() changes
- loop fix for leaking the backing reference file, if validation fails
- Update of a comment pertaining to disk/partition stat locking
* tag 'block-6.18-20251009' of git://git.kernel.org/pub/scm/linux/kernel/git/axboe/linux:
loop: remove redundant __GFP_NOWARN flag
block: move bio_iov_iter_get_bdev_pages to block/fops.c
iomap: open code bio_iov_iter_get_bdev_pages
block: rename bio_iov_iter_get_pages_aligned to bio_iov_iter_get_pages
block: remove bio_iov_iter_get_pages
block: Update a comment of disk statistics
loop: fix backing file reference leak on validation error
Linus Torvalds [Fri, 10 Oct 2025 17:25:24 +0000 (10:25 -0700)]
Merge tag 'io_uring-6.18-20251009' of git://git.kernel.org/pub/scm/linux/kernel/git/axboe/linux
Pull io_uring fixes from Jens Axboe:
- Fixup indentation in the UAPI header
- Two fixes for zcrx. One fixes receiving too much in some cases, and
the other deals with not correctly incrementing the source in the
fallback copy loop
- Fix for a race in the IORING_OP_WAITID command, where there was a
small window where the request would be left on the wait_queue_head
list even though it was being canceled/completed
- Update liburing git URL in the kernel tree
* tag 'io_uring-6.18-20251009' of git://git.kernel.org/pub/scm/linux/kernel/git/axboe/linux:
io_uring/zcrx: increment fallback loop src offset
io_uring/zcrx: fix overshooting recv limit
io_uring: use tab indentation for IORING_SEND_VECTORIZED comment
io_uring/waitid: always prune wait queue entry in io_waitid_wait()
io_uring: update liburing git URL
Merge patch series "kbuild: Fixes for fallout from recent modules.builtin.modinfo series"
This is a series to address some problems that were exposed by the
recent modules.builtin.modinfo series that landed in commit c7d3dd9163e6
("Merge patch series "Add generated modalias to
modules.builtin.modinfo"").
The third patch is not directly related to the aforementioned series, as
the warning it fixes happens prior to the series but commit 8d18ef04f940
("s390: vmlinux.lds.S: Reorder sections") from the series creates
conflicts in this area, so I included it here.
s390/vmlinux.lds.S: Move .vmlinux.info to end of allocatable sections
When building s390 defconfig with binutils older than 2.32, there are
several warnings during the final linking stage:
s390-linux-ld: .tmp_vmlinux1: warning: allocated section `.got.plt' not in segment
s390-linux-ld: .tmp_vmlinux2: warning: allocated section `.got.plt' not in segment
s390-linux-ld: vmlinux.unstripped: warning: allocated section `.got.plt' not in segment
s390-linux-objcopy: vmlinux: warning: allocated section `.got.plt' not in segment
s390-linux-objcopy: st7afZyb: warning: allocated section `.got.plt' not in segment
binutils commit afca762f598 ("S/390: Improve partial relro support for
64 bit") [1] in 2.32 changed where .got.plt is emitted, avoiding the
warning.
The :NONE in the .vmlinux.info output section description changes the
segment for subsequent allocated sections. Move .vmlinux.info right
above the discards section to place all other sections in the previously
defined segment, .data.
Prior to binutils commit c12d9fa2afe ("Support objcopy
--remove-section=.relaFOO") [1] in 2.32, stripping relocation sections
required the trailing period (i.e., '.rel.*') to work properly.
After commit 3e86e4d74c04 ("kbuild: keep .modinfo section in
vmlinux.unstripped"), there is an error with binutils 2.31.1 or earlier
because these sections are not properly removed:
s390-linux-objcopy: st6tO8Ev: symbol `.modinfo' required but not present
s390-linux-objcopy:st6tO8Ev: no symbols
Add the old pattern to resolve this issue (along with a comment to allow
cleaning this when binutils 2.32 or newer is the minimum supported
version). While the aforementioned kbuild change exposes this, the
pattern was originally changed by commit 71d815bf5dfd ("kbuild: Strip
runtime const RELA sections correctly"), where it would still be
incorrect with binutils older than 2.32.
kbuild: Restore pattern to avoid stripping .rela.dyn from vmlinux
Commit 0ce5139fd96e ("kbuild: always create intermediate
vmlinux.unstripped") removed the pattern to avoid stripping .rela.dyn
sections added by commit e9d86b8e17e7 ("scripts: Do not strip .rela.dyn
section"). Restore it so that .rela.dyn sections remain in the final
vmlinux.
KaFai Wan [Wed, 8 Oct 2025 10:26:27 +0000 (18:26 +0800)]
selftests/bpf: Add test for unpinning htab with internal timer struct
Add test to verify that unpinning hash tables containing internal timer
structures does not trigger context warnings.
Each subtest (timer_prealloc and timer_no_prealloc) can trigger the
context warning when unpinning, but the warning cannot be triggered
twice within a short time interval (a HZ), which is expected behavior.
KaFai Wan [Wed, 8 Oct 2025 10:26:26 +0000 (18:26 +0800)]
bpf: Avoid RCU context warning when unpinning htab with internal structs
When unpinning a BPF hash table (htab or htab_lru) that contains internal
structures (timer, workqueue, or task_work) in its values, a BUG warning
is triggered:
BUG: sleeping function called from invalid context at kernel/bpf/hashtab.c:244
in_atomic(): 1, irqs_disabled(): 0, non_block: 0, pid: 14, name: ksoftirqd/0
...
The issue arises from the interaction between BPF object unpinning and
RCU callback mechanisms:
1. BPF object unpinning uses ->free_inode() which schedules cleanup via
call_rcu(), deferring the actual freeing to an RCU callback that
executes within the RCU_SOFTIRQ context.
2. During cleanup of hash tables containing internal structures,
htab_map_free_internal_structs() is invoked, which includes
cond_resched() or cond_resched_rcu() calls to yield the CPU during
potentially long operations.
However, cond_resched() or cond_resched_rcu() cannot be safely called from
atomic RCU softirq context, leading to the BUG warning when attempting
to reschedule.
Fix this by changing from ->free_inode() to ->destroy_inode() and rename
bpf_free_inode() to bpf_destroy_inode() for BPF objects (prog, map, link).
This allows direct inode freeing without RCU callback scheduling,
avoiding the invalid context warning.
Reported-by: Le Chen <tom2cat@sjtu.edu.cn> Closes: https://lore.kernel.org/all/1444123482.1827743.1750996347470.JavaMail.zimbra@sjtu.edu.cn/ Fixes: 68134668c17f ("bpf: Add map side support for bpf timers.") Suggested-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: KaFai Wan <kafai.wan@linux.dev> Acked-by: Yonghong Song <yonghong.song@linux.dev> Link: https://lore.kernel.org/r/20251008102628.808045-2-kafai.wan@linux.dev Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Turned out certain clearly invalid values passed in xdp_desc from
userspace can pass xp_{,un}aligned_validate_desc() and then lead
to UBs or just invalid frames to be queued for xmit.
desc->len close to ``U32_MAX`` with a non-zero pool->tx_metadata_len
can cause positive integer overflow and wraparound, the same way low
enough desc->addr with a non-zero pool->tx_metadata_len can cause
negative integer overflow. Both scenarios can then pass the
validation successfully.
This doesn't happen with valid XSk applications, but can be used
to perform attacks.
Always promote desc->len to ``u64`` first to exclude positive
overflows of it. Use explicit check_{add,sub}_overflow() when
validating desc->addr (which is ``u64`` already).
bloat-o-meter reports a little growth of the code size:
add/remove: 0/0 grow/shrink: 2/1 up/down: 60/-16 (44)
Function old new delta
xskq_cons_peek_desc 299 330 +31
xsk_tx_peek_release_desc_batch 973 1002 +29
xsk_generic_xmit 3148 3132 -16
but hopefully this doesn't hurt the performance much.
Fixes: 341ac980eab9 ("xsk: Support tx_metadata_len") Cc: stable@vger.kernel.org # 6.8+ Signed-off-by: Alexander Lobakin <aleksander.lobakin@intel.com> Reviewed-by: Jason Xing <kerneljasonxing@gmail.com> Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com> Link: https://lore.kernel.org/r/20251008165659.4141318-1-aleksander.lobakin@intel.com Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Linus Torvalds [Fri, 10 Oct 2025 17:01:55 +0000 (10:01 -0700)]
Merge tag 'parisc-for-6.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux
Pull parisc updates from Helge Deller:
"Minor enhancements and fixes, specifically:
- report emulation and alignment faults via perf
- add initial kernel-side support for perf_events
- small initialization fixes in the parisc firmware layer
- adjust TC* constants and avoid referencing termio structs to avoid
userspace build errors"
* tag 'parisc-for-6.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Fix iodc and device path return values on old machines
parisc: Firmware: Fix returned path for PDC_MODULE_FIND on older machines
parisc: Add initial kernel-side perf_event support
parisc: Report software alignment faults via perf
parisc: Report emulation faults via perf
parisc: don't reference obsolete termio struct for TC* constants
parisc: Remove spurious if statement from raw_copy_from_user()
Linus Torvalds [Fri, 10 Oct 2025 16:55:19 +0000 (09:55 -0700)]
Merge tag 'sound-fix-6.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"A few more small fixes for 6.18-rc1.
Most of changes are about ASoC Intel and SOF drivers, while a few
other device-specific fixes are found for HD-audio, USB-audio, ASoC
RT722VB and Meson"
* tag 'sound-fix-6.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ASoC: rt722: add settings for rt722VB
ASoC: meson: aiu-encoder-i2s: fix bit clock polarity
ALSA: usb: fpc: replace kmalloc_array followed by copy_from_user with memdup_array_user
ALSA: hda/tas2781: Enable init_profile_id for device initialization
ALSA: emu10k1: Fix typo in docs
ALSA: hda/realtek: Add quirk for ASUS ROG Zephyrus Duo
ASoC: SOF: Intel: Read the LLP via the associated Link DMA channel
ASoC: SOF: ipc4-pcm: do not report invalid delay values
ASoC: SOF: sof-audio: add dev_dbg_ratelimited wrapper
ASoC: SOF: Intel: hda-pcm: Place the constraint on period time instead of buffer time
ASoC: SOF: ipc4-topology: Account for different ChainDMA host buffer size
ASoC: SOF: ipc4-topology: Correct the minimum host DMA buffer size
ASoC: SOF: ipc4-pcm: fix start offset calculation for chain DMA
ASoC: SOF: ipc4-pcm: fix delay calculation when DSP resamples
ASoC: SOF: ipc3-topology: Fix multi-core and static pipelines tear down
ALSA: hda/hdmi: Add pin fix for HP ProDesk model
Linus Torvalds [Fri, 10 Oct 2025 16:36:23 +0000 (09:36 -0700)]
Merge tag 'fbdev-for-6.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/linux-fbdev
Pull fbdev updates from Helge Deller:
"Beside the usual bunch of smaller bug fixes, the majority of changes
were by Zsolt Kajtar to improve the s3fb driver.
Bug fixes:
- Bounds checking to fix vmalloc-out-of-bounds (Albin Babu Varghese)
- Fix logic error in "offb" name match (Finn Thain)
- simplefb: Fix use after free in (Janne Grunau)
- s3fb: Various fixes and powersave improvements (Zsolt Kajtar)
Enhancements & code cleanups:
- Various fixes in the documentation (Bagas Sanjaya)
- Use string choices helpers (Chelsy Ratnawat)
- xenfb: Use vmalloc_array to simplify code (Qianfeng Rong)
- mb862xxfb: use signed type for error codes (Qianfeng Rong)
- Make drivers depend on LCD_CLASS_DEVICE (Thomas Zimmermann)
- radeonfb: Remove stale product link in Kconfig (Sukrut Heroorkar)"
* tag 'fbdev-for-6.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/linux-fbdev:
fbdev: Fix logic error in "offb" name match
fbdev: Add bounds checking in bit_putcs to fix vmalloc-out-of-bounds
fbdev: Make drivers depend on LCD_CLASS_DEVICE
fbdev: radeonfb: Remove stale product link in Kconfig
Documentation: fb: Retitle driver docs
Documentation: fb: ep93xx: Demote section headings
Documentation: fb: Split toctree
fbdev: simplefb: Fix use after free in simplefb_detach_genpds()
fbdev: s3fb: Revert mclk stop in suspend
fbdev: mb862xxfb: Use int type to store negative error codes
fbdev: Use string choices helpers
fbdev: core: Fix ubsan warning in pixel_to_pat
fbdev: s3fb: Implement 1 and 2 BPP modes, improve 4 BPP
fbdev: s3fb: Implement powersave for S3 FB
fbdev: xenfb: Use vmalloc_array to simplify code
Linus Torvalds [Fri, 10 Oct 2025 16:22:39 +0000 (09:22 -0700)]
Merge tag 'gpio-fixes-for-v6.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux
Pull gpio fixes from Bartosz Golaszewski:
- add a missing ACPI ID for MTL-CVF devices in gpio-usbio
- mark the gpio-wcd934x controller as "sleeping" as it uses a mutex for
locking internally
* tag 'gpio-fixes-for-v6.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux:
gpio: wcd934x: mark the GPIO controller as sleeping
gpio: usbio: Add ACPI device-id for MTL-CVF devices
Linus Torvalds [Fri, 10 Oct 2025 16:18:19 +0000 (09:18 -0700)]
Merge tag 'ntb-6.18' of https://github.com/jonmason/ntb
Pull NTB updates from Jon Mason:
- Add support for Renesas R-Car and allow arbitrary BAR mapping in EPF
- Update ntb_hw_amd to support the latest generation secondary topology
and add a new maintainer
- Fix a bug by adding a mutex to ensure `link_event_callback` executes
sequentially
* tag 'ntb-6.18' of https://github.com/jonmason/ntb:
NTB: epf: Add Renesas rcar support
NTB: epf: Allow arbitrary BAR mapping
ntb: Add mutex to make link_event_callback executed linearly.
MAINTAINERS: Update for the NTB AMD driver maintainer
ntb_hw_amd: Update amd_ntb_get_link_status to support latest generation secondary topology
Linus Torvalds [Fri, 10 Oct 2025 16:13:11 +0000 (09:13 -0700)]
Merge tag 'i2c-for-6.18-rc1-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull more i2c updates from Wolfram Sang:
- Second part of rtl9300 updates since dependencies are in now:
- general cleanups
- implement block read/write support
- add RTL9310 support
- DT schema conversion of hix5hd2 binding
- namespace cleanup for i2c-algo-pca
- minor simplification for mt65xx
* tag 'i2c-for-6.18-rc1-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
dt-bindings: i2c: hisilicon,hix5hd2: convert to DT schema
i2c: mt65xx: convert set_speed function to void
i2c: rename wait_for_completion callback to wait_for_completion_cb
i2c: rtl9300: add support for RTL9310 I2C controller
dt-bindings: i2c: realtek,rtl9301-i2c: extend for RTL9310 support
i2c: rtl9300: use scoped guard instead of explicit lock/unlock
i2c: rtl9300: separate xfer configuration and execution
i2c: rtl9300: do not set read mode on every transfer
i2c: rtl9300: move setting SCL frequency to config_io
i2c: rtl9300: rename internal sda_pin to sda_num
dt-bindings: i2c: realtek,rtl9301-i2c: fix wording and typos
i2c: rtl9300: use regmap fields and API for registers
i2c: rtl9300: Implement I2C block read and write
Linus Torvalds [Fri, 10 Oct 2025 15:34:11 +0000 (08:34 -0700)]
Merge tag 'tpmdd-next-v6.18-2' of git://git.kernel.org/pub/scm/linux/kernel/git/jarkko/linux-tpmdd
Pull tpm updates from Jarkko Sakkinen:
- Disable TCG_TPM2_HMAC from defconfig
It causes performance issues, and breaks some atypical
configurations.
- simplify code using the new crypto library
- misc fixes and cleanups
* tag 'tpmdd-next-v6.18-2' of git://git.kernel.org/pub/scm/linux/kernel/git/jarkko/linux-tpmdd:
tpm: Prevent local DOS via tpm/tpm0/ppi/*operations
tpm: use a map for tpm2_calc_ordinal_duration()
tpm_tis: Fix incorrect arguments in tpm_tis_probe_irq_single
tpm: Use HMAC-SHA256 library instead of open-coded HMAC
tpm: Compare HMAC values in constant time
tpm: Disable TPM2_TCG_HMAC by default
The ozlabs.org PW instance is slow due to being geographically far away
from any of the maintainers and seems to have gotten slower as of late
(AI scrapers perhaps). The kernel.org PW also has some additional
features (i.e. pwbot) we want to use.
DT core patches also go into PW, so add the PW link for it.
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
gpio: wcd934x: mark the GPIO controller as sleeping
The slimbus regmap passed to the GPIO driver down from MFD does not use
fast_io. This means a mutex is used for locking and thus this GPIO chip
must not be used in atomic context. Change the can_sleep switch in
struct gpio_chip to true.
Fixes: 59c324683400 ("gpio: wcd934x: Add support to wcd934x gpio controller") Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
tpm: Prevent local DOS via tpm/tpm0/ppi/*operations
Reads on tpm/tpm0/ppi/*operations can become very long on
misconfigured systems. Reading the TPM is a blocking operation,
thus a user could effectively trigger a DOS.
Resolve this by caching the results and avoiding the blocking
operations after the first read.
[ jarkko: fixed atomic sleep:
sed -i 's/spin_/mutex_/g' drivers/char/tpm/tpm_ppi.c
sed -i 's/DEFINE_SPINLOCK/DEFINE_MUTEX/g' drivers/char/tpm/tpm_ppi.c ]
Signed-off-by: Denis Aleksandrov <daleksan@redhat.com> Reported-by: Jan Stancek <jstancek@redhat.com> Closes: https://lore.kernel.org/linux-integrity/20250915210829.6661-1-daleksan@redhat.com/T/#u Suggested-by: Jarkko Sakkinen <jarkko@kernel.org> Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de> Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
Jarkko Sakkinen [Thu, 18 Sep 2025 19:30:18 +0000 (22:30 +0300)]
tpm: use a map for tpm2_calc_ordinal_duration()
The current shenanigans for duration calculation introduce too much
complexity for a trivial problem, and further the code is hard to patch and
maintain.
Address these issues with a flat look-up table, which is easy to understand
and patch. If leaf driver specific patching is required in future, it is
easy enough to make a copy of this table during driver initialization and
add the chip parameter back.
'chip->duration' is retained for TPM 1.x.
As the first entry for this new behavior address TCG spec update mentioned
in this issue:
https://github.com/raspberrypi/linux/issues/7054
Therefore, for TPM_SelfTest the duration is set to 3000 ms.
This does not categorize a as bug, given that this is introduced to the
spec after the feature was originally made.
Reviewed-by: Serge Hallyn <serge@hallyn.com> Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
tpm_tis: Fix incorrect arguments in tpm_tis_probe_irq_single
The tpm_tis_write8() call specifies arguments in wrong order. Should be
(data, addr, value) not (data, value, addr). The initial correct order
was changed during the major refactoring when the code was split.
Fixes: 41a5e1cf1fe1 ("tpm/tpm_tis: Split tpm_tis driver into a core and TCG TIS compliant phy") Signed-off-by: Gunnar Kudrjavets <gunnarku@amazon.com> Reviewed-by: Justinien Bouron <jbouron@amazon.com> Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org> Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de> Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
Eric Biggers [Fri, 1 Aug 2025 21:24:22 +0000 (14:24 -0700)]
tpm: Use HMAC-SHA256 library instead of open-coded HMAC
Now that there are easy-to-use HMAC-SHA256 library functions, use these
in tpm2-sessions.c instead of open-coding the HMAC algorithm.
Note that the new implementation correctly handles keys longer than 64
bytes (SHA256_BLOCK_SIZE), whereas the old implementation handled such
keys incorrectly. But it doesn't appear that such keys were being used.
Signed-off-by: Eric Biggers <ebiggers@kernel.org> Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org> Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
Eric Biggers [Fri, 1 Aug 2025 21:24:21 +0000 (14:24 -0700)]
tpm: Compare HMAC values in constant time
In tpm_buf_check_hmac_response(), compare the HMAC values in constant
time using crypto_memneq() instead of in variable time using memcmp().
This is worthwhile to follow best practices and to be consistent with
MAC comparisons elsewhere in the kernel. However, in this driver the
side channel seems to have been benign: the HMAC input data is
guaranteed to always be unique, which makes the usual MAC forgery via
timing side channel not possible. Specifically, the HMAC input data in
tpm_buf_check_hmac_response() includes the "our_nonce" field, which was
generated by the kernel earlier, remains under the control of the
kernel, and is unique for each call to tpm_buf_check_hmac_response().
Signed-off-by: Eric Biggers <ebiggers@kernel.org> Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
Jarkko Sakkinen [Mon, 25 Aug 2025 20:32:23 +0000 (23:32 +0300)]
tpm: Disable TPM2_TCG_HMAC by default
After reading all the feedback, right now disabling the TPM2_TCG_HMAC
is the right call.
Other views discussed:
A. Having a kernel command-line parameter or refining the feature
otherwise. This goes to the area of improvements. E.g., one
example is my own idea where the null key specific code would be
replaced with a persistent handle parameter (which can be
*unambigously* defined as part of attestation process when
done correctly).
B. Removing the code. I don't buy this because that is same as saying
that HMAC encryption cannot work at all (if really nitpicking) in
any form. Also I disagree on the view that the feature could not
be refined to something more reasoable.
Also, both A and B are worst options in terms of backporting.
Thuss, this is the best possible choice.
Cc: stable@vger.kernel.or # v6.10+ Fixes: d2add27cf2b8 ("tpm: Add NULL primary creation") Suggested-by: Chris Fenner <cfenn@google.com> Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
projects / thirdparty / kernel / linux.git / log
