In https://bugzilla.kernel.org/show_bug.cgi?id=67561, a locking dependency is reported
when b43 is used with hostapd, and rfkill is used to kill the radio output.
The lockdep splat (in part) is as follows:
======================================================
[ INFO: possible circular locking dependency detected ]
3.12.0 #1 Not tainted
-------------------------------------------------------
rfkill/10040 is trying to acquire lock:
(rtnl_mutex){+.+.+.}, at: [<ffffffff8146f282>] rtnl_lock+0x12/0x20
but task is already holding lock:
(rfkill_global_mutex){+.+.+.}, at: [<ffffffffa04832ca>] rfkill_fop_write+0x6a/0x170 [rfkill]
Cleanup of iwl_mvm_leds was missing in case of error,
resulting in the following warning:
WARNING: at lib/kobject.c:196 kobject_add_internal+0x1f4/0x210()
kobject_add_internal failed for phy0-led with -EEXIST, don't try to register things with the same name in the same directory.
Enabling the oscillator consumes slightly more power (100uA)
but allows to make sure that we exit from L1 on time.
Not doing so might lead to a PCIe specification violation
since we might wake up from L1 at the wrong time.
This issue has been identified on 3160 and 7260 only.
On older NICs L1 off is not enabled, on newer NICs (7265),
the issue is fixed.
When the bug occurs the user sees that the NIC has
disappeared from the PCI bridge, any access to the device
returns 0xff.
This fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=64541
and has been extensively discussed here:
http://markmail.org/thread/mfmpzqt3r333n4bo
The static analyser "cppcheck" shows the following typo:
drivers/net/wireless/rtlwifi/rtl8188ee/dm.c:1081]: (style) Same expression on both sides of '!='.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Reported-by: David Binderman <dcb314@hotmail.com> Cc: David Binderman <dcb314@hotmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The vendor driver contained a number of improvements in the gain settings
for the rtl8192c{e,u} devices. This patch implements them in the kernel
driver.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch uses the newly introduced power index register routines.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current number of RX buffers queued is 32, which is too small under
heavy load. That number is doubled.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Changes in the gain-control mechanism will require some changes in the header.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The present code fails to set the linked state when an interface is
added.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The initial USB driver did not use some register save locations in the
private data storage. To save some memory, a union was used to overlay these
variables with USB I/O components. In an update of the gain-control code,
these register save locations are now needed for USB drivers.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Vendor driver rtl8188C_8192C_8192D_usb_linux_v3.4.2_3727.20120404 introduced
new firmware for these chips. The code try for the new file, and fall back to
the original firmware if the new file is not available.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This driver has a watchdog timer that attempts to reconnect when beacon frames
are not seen for 6 seconds. This patch disables that reconnect whenever the
device has never been connected.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The USB drivers were not updating the beacon statistics, which led to
false beacon loss indications.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reported-by: Jan Prinsloo <janroot@gmail.com> Tested-by: Jan Prinsloo <janroot@gmail.com> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to Freescale imx28 Errata, "ENGR119653 USB: ARM to USB
register error issue", All USB register write operations must
use the ARM SWP instruction. So, we implement a special ehci_write
for imx28.
Discussion for it at below:
http://marc.info/?l=linux-usb&m=137996395529294&w=2
Without this patcheset, imx28 works unstable at high AHB bus loading.
If the bus loading is not high, the imx28 usb can work well at the most
of time. There is a IC errata for this problem, usually, we consider
IC errata is a problem not a new feature, and this workaround is needed
for that, so we need to add them to stable tree 3.11+.
Cc: robert.hodaszi@digi.com Signed-off-by: Peter Chen <peter.chen@freescale.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Tested-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a race in the hub driver between hub_disconnect() and
recursively_mark_NOTATTACHED(). This race can be triggered if the
driver is unbound from a device at the same time as the bus's root hub
is removed. When the race occurs, it can cause an oops:
One problem is that recursively_mark_NOTATTACHED() uses the intfdata
value and hub->hdev->maxchild while hub_disconnect() is clearing them.
Another problem is that it uses hub->ports[i] while the port device is
being released.
To fix this race, we need to hold the device_state_lock while
hub_disconnect() changes the values. (Note that usb_disconnect()
and hub_port_connect_change() already acquire this lock at similar
critical times during a USB device's life cycle.) We also need to
remove the port devices after maxchild has been set to 0, instead of
before.
If CONFIG_PCI is enabled, make sure xhci_cleanup_msix()
doesn't try to free a bogus PCI IRQ or dereference an invalid
pci_dev when the xHCI device is actually a platform_device.
This patch should be backported to kernels as old as 3.9, that
contain the commit 52fb61250a7a132b0cfb9f4a1060a1f3c49e5a25
"xhci-plat: Don't enable legacy PCI interrupts."
Signed-off-by: Jack Pham <jackp@codeaurora.org> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The USB storage operation of Nokia Asha 502 Dual SIM smartphone running Asha
Platform 1.1.1 is unreliable in respect of data consistency (i.e. transfered
files are corrupted). A similar issue is described here:
http://discussions.nokia.com/t5/Asha-and-other-Nokia-Series-30/Nokia-301-USB-transfers-and-corrupted-files/td-p/1974170
The workaround is (MAX_SECTORS_64):
rmmod usb_storage && modprobe usb_storage quirks=0421:06aa:m
The patch adds the tested device to the unusual list permanently.
Genuine FTDI chips support only CS7/8. A previous fix in commit 8704211f65a2 ("USB: ftdi_sio: fixed handling of unsupported CSIZE
setting") enforced this limitation and reported it back to userspace.
However, certain types of smartcard readers depend on specific
driver behaviour that requests 0 data bits (not 5) to change into a
different operating mode if CS5 has been set.
This patch reenables this behaviour for all FTDI devices.
Tagged to be added to stable, because it affects a lot of users of
embedded systems which rely on these readers to work properly.
Reported-by: Heinrich Siebmanns <H.Siebmanns@t-online.de> Tested-by: Heinrich Siebmanns <H.Siebmanns@t-online.de> Signed-off-by: Colin Leitner <colin.leitner@gmail.com> Signed-off-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix ring-indicator (RI) status-bit definition, which was defined as CTS,
effectively preventing RI-changes from being detected while reporting
false RI status.
This bug predates git.
Signed-off-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some PL2303 devices are known to lose bytes if you change serial
settings even to the same values as before. Avoid this by comparing the
encoded settings with the previsouly used ones before configuring the
device.
The common case was fixed by commit bf5e5834bffc6 ("pl2303: Fix mode
switching regression"), but this problem was still possible to trigger,
for instance, by using the TCSETS2-interface to repeatedly request
115201 baud, which gets mapped to 115200 and thus always triggers a
settings update.
Cc: Frank Schäfer <fschaefer.oss@googlemail.com> Signed-off-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The reset_gpio member of the usb_phy_gen_xceiv_platform_data
structure needs the have negative value or phy-generic's
probe will fail unless DT is used. 0 is a valid gpio number.
This fixes an issue where phy-generic fails to probe with
message: "usb_phy_gen_xceiv.0: Error requesting RESET GPIO 0".
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We set resp_count to 0 when the device is closed. The next open and
read will try to clear the WDM_READ flag if there was leftover data
in the read buffer. This fix is necessary to prevent resubmitting
the read URB in a tight loop because resp_count becomes negative.
The bug can easily be triggered from userspace by not reading all
data in the read buffer, and then closing and reopening the chardev.
commit 73e06865ead1 ("USB: cdc-wdm: support back-to-back
USB_CDC_NOTIFY_RESPONSE_AVAILABLE notifications") implemented
queued response handling. This added a new requirement: The read
urb must be resubmitted every time we clear the WDM_READ flag if
the response counter indicates that the device is waiting for a
read.
Fix by factoring out the code handling the WMD_READ clearing and
possible urb submission, calling it everywhere we clear the flag.
Without this fix, the driver ends up in a state where the read urb
is inactive, but the response counter is positive after a zero
length read. This prevents the read urb from ever being submitted
again and the driver appears to be hanging.
We have met a bug that the high bandwidth ISO-TX transfer has failed
at the last packet if it is less than 1024, the TD status shows it
is "Transaction Error".
The root cause of this problem is: the mult value at qh is not correct
for current TD's transfer length. We use TD list to queue un-transfer
TDs, and change mult for new adding TDs. If new adding TDs transfer length
less than 1024, but the queued un-transfer TDs transfer length is larger
than 1024, the transfer error will occur, and vice versa.
Usually, this problem occurs at the last packet, and the first packet for
new frame.
We fixed this problem by setting Mult at QH as the largest value (3), and
set MultO (Multiplier Override) at TD according to every transfer length.
It can cover both hardware version less than 2.3 (the real mult is MultO
if it is not 0) and 2.3+ (the real mult is min(qh.mult, td.multo)).
Since the MultO bits are only existed at TX TD, we keep the ISO-RX behavior
unchanged.
For stable tree: 3.11+.
Cc: Michael Grzeschik <m.grzeschik@pengutronix.de> Reported-by: Matthieu Vanin <b47495@freescale.com> Tested-by: Matthieu Vanin <b47495@freescale.com> Signed-off-by: Peter Chen <peter.chen@freescale.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For otgsc, both enable bits and status bits are in it. So we need
to make sure the status bits are not be cleared when write enable
bits. It can fix one bug that we plug in/out Micro AB cable fast,
and sometimes, the IDIS will be cleared wrongly when handle last
ID interrupt (ID 0->1), so the current interrupt will not occur.
For stable tree: 3.12+
Signed-off-by: Peter Chen <peter.chen@freescale.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to Freescale imx28 Errata, "ENGR119653 USB: ARM to USB
register error issue", All USB register write operations must
use the ARM SWP instruction. So, we implement special hw_write
and hw_test_and_clear for imx28.
Discussion for it at below:
http://marc.info/?l=linux-usb&m=137996395529294&w=2
This patch is needed for stable tree 3.11+.
Cc: robert.hodaszi@digi.com Signed-off-by: Peter Chen <peter.chen@freescale.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Tested-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When Hyper-V hypervisor leaves are present, KVM must relocate
its own leaves at 0x40000100, because Windows does not look for
Hyper-V leaves at indices other than 0x40000000. In this case,
the KVM features are at 0x40000101, but the old code would always
look at 0x40000001.
Fix by using kvm_cpuid_base(). This also requires making the
function non-inline, since kvm_cpuid_base() is static.
It is unnecessary to go through hypervisor_cpuid_base every time
a leaf is found (which will be every time a feature is requested
after the next patch).
Current code check boot service region with kernel text region by:
start+size >= __pa_symbol(_text)
The end of the above region should be start + size - 1 instead.
I see this problem in ovmf + Fedora 19 grub boot:
text start: 1000000 md start: 800000 md size: 800000
Signed-off-by: Dave Young <dyoung@redhat.com> Acked-by: Borislav Petkov <bp@suse.de> Acked-by: Toshi Kani <toshi.kani@hp.com> Tested-by: Toshi Kani <toshi.kani@hp.com> Signed-off-by: Matt Fleming <matt.fleming@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The timeout pointer parameter is provided by userland (hence the __user
annotation) but for x32 syscalls it's simply cast to a kernel pointer
and is passed to __sys_recvmmsg which will eventually directly
dereference it for both reading and writing. Other callers to
__sys_recvmmsg properly copy from userland to the kernel first.
The bug was introduced by commit ee4fa23c4bfc ("compat: Use
COMPAT_USE_64BIT_TIME in net/compat.c") and should affect all kernels
since 3.4 (and perhaps vendor kernels if they backported x32 support
along with this code).
Note that CONFIG_X86_X32_ABI gets enabled at build time and only if
CONFIG_X86_X32 is enabled and ld can build x32 executables.
Other uses of COMPAT_USE_64BIT_TIME seem fine.
This addresses CVE-2014-0038.
Signed-off-by: PaX Team <pageexec@freemail.hu> Signed-off-by: H. Peter Anvin <hpa@linux.intel.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As a result of commit 5606e3877ad8 ("mm: numa: Migrate on reference
policy"), /proc/<pid>/numa_maps prints the mempolicy for any <pid> as
"prefer:N" for the local node, N, of the process reading the file.
This should only be printed when the mempolicy of <pid> is
MPOL_PREFERRED for node N.
If the process is actually only using the default mempolicy for local
node allocation, make sure "default" is printed as expected.
Signed-off-by: David Rientjes <rientjes@google.com> Reported-by: Robert Lippert <rlippert@google.com> Cc: Peter Zijlstra <peterz@infradead.org> Acked-by: Mel Gorman <mgorman@suse.de> Cc: Ingo Molnar <mingo@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case the device 0, function 1 is not found using pci_get_device(),
pci_scan_single_device() will be used but, differently than
pci_get_device(), it allocates a pci_dev but doesn't does bump the usage
count on the pci_dev and after few module removals and loads the pci_dev
will be freed.
As release_stripe and __release_stripe decrement ->count and then
manipulate ->lru both under ->device_lock, it is important that
get_active_stripe() increments ->count and clears ->lru also under
->device_lock.
However we currently list_del_init ->lru under the lock, but increment
the ->count outside the lock. This can lead to races and list
corruption.
So move the atomic_inc(&sh->count) up inside the ->device_lock
protected region.
Note that we still increment ->count without device lock in the case
where get_free_stripe() was called, and in fact don't take
->device_lock at all in that path.
This is safe because if the stripe_head can be found by
get_free_stripe, then the hash lock assures us the no-one else could
possibly be calling release_stripe() at the same time.
Before a write starts we set a bit in the write-intent bitmap.
When the write completes we clear that bit if the write was successful
to all devices. However if the write wasn't fully successful we
should not clear the bit. If the faulty drive is subsequently
re-added, the fact that the bit is still set ensure that we will
re-write the data that is missing.
This logic is mediated by the STRIPE_DEGRADED flag - we only clear the
bitmap bit when this flag is not set.
Currently we correctly set the flag if a write starts when some
devices are failed or missing. But we do *not* set the flag if some
device failed during the write attempt.
This is wrong and can result in clearing the bit inappropriately.
So: set the flag when a write fails.
This bug has been present since bitmaps were introduces, so the fix is
suitable for any -stable kernel.
Commit 338de0ca (extcon: gpio: Use gpio driver/chip debounce if supported)
introduced a call to gpio_set_debounce() before actually requesting the
respective gpio pin from the gpio subsystem.
The gpio subsystem expects that a gpio pin was requested before modifying its
state. Not doing so results in a warning from gpiolib, and the gpio pin is
auto-requested. This in turn causes the subsequent devm_gpio_request_one()
to fail. So devm_gpio_request_one() must be called prior to calling
gpio_set_debounce().
When the pl011 is being used for a console, pl011_console_write forces
the control register (CR) to enable the UART for transmission and then
restores this to the original value afterwards. It does this while
holding the port lock.
Unfortunately, when the uart is started or shutdown - say in response to
userland using the serial device for a terminal - then this updates the
control register without any locking.
This means we can have
pl011_console_write Save CR
pl011_startup Initialise CR, e.g. enable receive
pl011_console_write Restore old CR with receive not enabled
this result is a serial port which doesn't respond to any input.
A similar race in reverse could happen when the device is shutdown.
We can fix these problems by taking the port lock when updating CR.
Signed-off-by: Jon Medhurst <tixy@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
{,set}page_address() are macros if WANT_PAGE_VIRTUAL. If
!WANT_PAGE_VIRTUAL, they're plain C functions.
If someone calls them with a void *, this pointer is auto-converted to
struct page * if !WANT_PAGE_VIRTUAL, but causes a build failure on
architectures using WANT_PAGE_VIRTUAL (arc, m68k and sparc64):
drivers/md/bcache/bset.c: In function `__btree_sort':
drivers/md/bcache/bset.c:1190: warning: dereferencing `void *' pointer
drivers/md/bcache/bset.c:1190: error: request for member `virtual' in something not a structure or union
Convert them to static inline functions to fix this. There are already
plenty of users of struct page members inside <linux/mm.h>, so there's
no reason to keep them as macros.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org> Acked-by: Michael S. Tsirkin <mst@redhat.com> Tested-by: Guenter Roeck <linux@roeck-us.net> Tested-by: David Rientjes <rientjes@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The dev->irq passed to request_irq() will always be 0 when the auto_attach
function is called. The pcidev->irq should be used instead to get the correct
irq number.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com> Reviewed-by: Ian Abbott <abbotti@mev.co.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the channel list is not set in userspace we get an error at
PTR_ERR(async->cmd.chanlist). However, do_become_nonbusy(dev, s) cleans
up this pointer which causes a kernel ooops. Setting the channel list in
async to NULL and checking this in do_become_nonbusy prevents the oops.
[Ian Abbott] Also do the same for the chanlist allocated in
do_cmdtest_ioctl().
This patch calls get_write_access in function gfs2_setattr_chown,
which merely increases inode->i_writecount for the duration of the
function. That will ensure that any file closes won't delete the
inode's multi-block reservation while the function is running.
It also ensures that a multi-block reservation exists when needed
for quota change operations during the chown.
Signed-off-by: Bob Peterson <rpeterso@redhat.com> Signed-off-by: Steven Whitehouse <swhiteho@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ilia Mirkin [Sun, 19 Jan 2014 15:30:32 +0000 (10:30 -0500)]
drm/nouveau/mxm: fix null deref on load
Since commit 61b365a505d6 ("drm/nouveau: populate master subdev pointer
only when fully constructed"), the nouveau_mxm(bios) call will return
NULL, since it's still being called from the constructor. Instead, pass
the mxm pointer via the unused data field.
See https://bugs.freedesktop.org/show_bug.cgi?id=73791
Reported-by: Andreas Reis <andreas.reis@gmail.com> Tested-by: Andreas Reis <andreas.reis@gmail.com> Signed-off-by: Ilia Mirkin <imirkin@alum.mit.edu> Cc: Ben Skeggs <bskeggs@redhat.com> Cc: Dave Airlie <airlied@linux.ie> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Mon, 20 Jan 2014 01:18:13 +0000 (17:18 -0800)]
Merge tag 'acpi-3.13-fixup' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull last-minute ACPI fix from Rafael Wysocki:
"This reverts a commit that causes the Alan Cox' ASUS T100TA to "crash
and burn" during boot if the Baytrail pinctrl driver is compiled in"
* tag 'acpi-3.13-fixup' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
Revert "ACPI: Add BayTrail SoC GPIO and LPSS ACPI IDs"
Linus Torvalds [Sun, 19 Jan 2014 21:06:51 +0000 (13:06 -0800)]
Merge branch 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Ingo Molnar:
- an s2ram related fix on AMD systems
- a perf fault handling bug that is relatively old but which has become
much easier to trigger in v3.13 after commit e00b12e64be9 ("perf/x86:
Further optimize copy_from_user_nmi()")
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/x86/amd/ibs: Fix waking up from S3 for AMD family 10h
x86, mm, perf: Allow recursive faults from interrupts
Revert "ACPI: Add BayTrail SoC GPIO and LPSS ACPI IDs"
This reverts commit f6308b36c411 (ACPI: Add BayTrail SoC GPIO and LPSS
ACPI IDs), because it causes the Alan Cox' ASUS T100TA to "crash and
burn" during boot if the Baytrail pinctrl driver is compiled in.
Fixes: f6308b36c411 (ACPI: Add BayTrail SoC GPIO and LPSS ACPI IDs) Reported-by: One Thousand Gnomes <gnomes@lxorguk.ukuu.org.uk> Requested-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
1) The value choosen for the new SO_MAX_PACING_RATE socket option on
parisc was very poorly choosen, let's fix it while we still can.
From Eric Dumazet.
2) Our generic reciprocal divide was found to handle some edge cases
incorrectly, part of this is encoded into the BPF as deep as the JIT
engines themselves. Just use a real divide throughout for now.
From Eric Dumazet.
3) Because the initial lookup is lockless, the TCP metrics engine can
end up creating two entries for the same lookup key. Fix this by
doing a second lookup under the lock before we actually create the
new entry. From Christoph Paasch.
4) Fix scatter-gather list init in usbnet driver, from Bjørn Mork.
5) Fix unintended 32-bit truncation in cxgb4 driver's bit shifting.
From Dan Carpenter.
6) Netlink socket dumping uses the wrong socket state for timewait
sockets. Fix from Neal Cardwell.
7) Fix netlink memory leak in ieee802154_add_iface(), from Christian
Engelmayer.
8) Multicast forwarding in ipv4 can overflow the per-rule reference
counts, causing all multicast traffic to cease. Fix from Hannes
Frederic Sowa.
9) via-rhine needs to stop all TX queues when it resets the device,
from Richard Weinberger.
10) Fix RDS per-cpu accesses broken by the this_cpu_* conversions. From
Gerald Schaefer.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
s390/bpf,jit: fix 32 bit divisions, use unsigned divide instructions
parisc: fix SO_MAX_PACING_RATE typo
ipv6: simplify detection of first operational link-local address on interface
tcp: metrics: Avoid duplicate entries with the same destination-IP
net: rds: fix per-cpu helper usage
e1000e: Fix compilation warning when !CONFIG_PM_SLEEP
bpf: do not use reciprocal divide
be2net: add dma_mapping_error() check for dma_map_page()
bnx2x: Don't release PCI bars on shutdown
net,via-rhine: Fix tx_timeout handling
batman-adv: fix batman-adv header overhead calculation
qlge: Fix vlan netdev features.
net: avoid reference counter overflows on fib_rules in multicast forwarding
dm9601: add USB IDs for new dm96xx variants
MAINTAINERS: add virtio-dev ML for virtio
ieee802154: Fix memory leak in ieee802154_add_iface()
net: usbnet: fix SG initialisation
inet_diag: fix inet_diag_dump_icsk() to use correct state for timewait sockets
cxgb4: silence shift wrapping static checker warning
Heiko Carstens [Fri, 17 Jan 2014 08:37:15 +0000 (09:37 +0100)]
s390/bpf,jit: fix 32 bit divisions, use unsigned divide instructions
The s390 bpf jit compiler emits the signed divide instructions "dr" and "d"
for unsigned divisions.
This can cause problems: the dividend will be zero extended to a 64 bit value
and the divisor is the 32 bit signed value as specified A or X accumulator,
even though A and X are supposed to be treated as unsigned values.
The divide instrunctions will generate an exception if the result cannot be
expressed with a 32 bit signed value.
This is the case if e.g. the dividend is 0xffffffff and the divisor either 1
or also 0xffffffff (signed: -1).
To avoid all these issues simply use unsigned divide instructions.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Thu, 16 Jan 2014 19:15:12 +0000 (11:15 -0800)]
parisc: fix SO_MAX_PACING_RATE typo
SO_MAX_PACING_RATE definition on parisc got a typo.
Its not too late to fix it, before 3.13 is official.
Fixes: 62748f32d501 ("net: introduce SO_MAX_PACING_RATE") Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
ipv6: simplify detection of first operational link-local address on interface
In commit 1ec047eb4751e3 ("ipv6: introduce per-interface counter for
dad-completed ipv6 addresses") I build the detection of the first
operational link-local address much to complex. Additionally this code
now has a race condition.
Replace it with a much simpler variant, which just scans the address
list when duplicate address detection completes, to check if this is
the first valid link local address and send RS and MLD reports then.
Fixes: 1ec047eb4751e3 ("ipv6: introduce per-interface counter for dad-completed ipv6 addresses") Reported-by: Jiri Pirko <jiri@resnulli.us> Cc: Flavio Leitner <fbl@redhat.com> Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Acked-by: Flavio Leitner <fbl@redhat.com> Acked-by: Jiri Pirko <jiri@resnulli.us> Signed-off-by: David S. Miller <davem@davemloft.net>
Christoph Paasch [Thu, 16 Jan 2014 19:01:21 +0000 (20:01 +0100)]
tcp: metrics: Avoid duplicate entries with the same destination-IP
Because the tcp-metrics is an RCU-list, it may be that two
soft-interrupts are inside __tcp_get_metrics() for the same
destination-IP at the same time. If this destination-IP is not yet part of
the tcp-metrics, both soft-interrupts will end up in tcpm_new and create
a new entry for this IP.
So, we will have two tcp-metrics with the same destination-IP in the list.
This patch checks twice __tcp_get_metrics(). First without holding the
lock, then while holding the lock. The second one is there to confirm
that the entry has not been added by another soft-irq while waiting for
the spin-lock.
Fixes: 51c5d0c4b169b (tcp: Maintain dynamic metrics in local cache.) Signed-off-by: Christoph Paasch <christoph.paasch@uclouvain.be> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Gerald Schaefer [Thu, 16 Jan 2014 15:54:48 +0000 (16:54 +0100)]
net: rds: fix per-cpu helper usage
commit ae4b46e9d "net: rds: use this_cpu_* per-cpu helper" broke per-cpu
handling for rds. chpfirst is the result of __this_cpu_read(), so it is
an absolute pointer and not __percpu. Therefore, __this_cpu_write()
should not operate on chpfirst, but rather on cache->percpu->first, just
like __this_cpu_read() did before.
Linus Torvalds [Sat, 18 Jan 2014 01:29:36 +0000 (17:29 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace
Pull namespace fixes from Eric Biederman:
"This is a set of 3 regression fixes.
This fixes /proc/mounts when using "ip netns add <netns>" to display
the actual mount point.
This fixes a regression in clone that broke lxc-attach.
This fixes a regression in the permission checks for mounting /proc
that made proc unmountable if binfmt_misc was in use. Oops.
My apologies for sending this pull request so late. Al Viro gave
interesting review comments about the d_path fix that I wanted to
address in detail before I sent this pull request. Unfortunately a
bad round of colds kept from addressing that in detail until today.
The executive summary of the review was:
Al: Is patching d_path really sufficient?
The prepend_path, d_path, d_absolute_path, and __d_path family of
functions is a really mess.
Me: Yes, patching d_path is really sufficient. Yes, the code is mess.
No it is not appropriate to rewrite all of d_path for a regression
that has existed for entirely too long already, when a two line
change will do"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace:
vfs: Fix a regression in mounting proc
fork: Allow CLONE_PARENT after setns(CLONE_NEWPID)
vfs: In d_path don't call d_dname on a mount point
David S. Miller [Fri, 17 Jan 2014 01:16:43 +0000 (17:16 -0800)]
Merge tag 'batman-adv-fix-for-davem' of git://git.open-mesh.org/linux-merge
Included change:
- properly compute the batman-adv header overhead. Such
result is later used to initialize the hard_header_len
member of the soft-interface netdev object
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Fri, 17 Jan 2014 00:33:27 +0000 (11:33 +1100)]
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fix from Catalin Marinas:
"Revert "arm64: Fix memory shareability attribute for ioremap_wc/cache"
We noticed that it breaks ioremap (and earlyprintk) with 64K page
configuration"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
Revert "arm64: Fix memory shareability attribute for ioremap_wc/cache"
Hugh Dickins [Thu, 16 Jan 2014 23:26:48 +0000 (15:26 -0800)]
percpu_counter: unbreak __percpu_counter_add()
Commit 74e72f894d56 ("lib/percpu_counter.c: fix __percpu_counter_add()")
looked very plausible, but its arithmetic was badly wrong: obvious once
you see the fix, but maddening to get there from the weird tmpfs ENOSPCs
Signed-off-by: Hugh Dickins <hughd@google.com> Cc: Ming Lei <tom.leiming@gmail.com> Cc: Paul Gortmaker <paul.gortmaker@windriver.com> Cc: Shaohua Li <shli@fusionio.com> Cc: Jens Axboe <axboe@kernel.dk> Cc: Fan Du <fan.du@windriver.com> Cc: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mika Westerberg [Thu, 16 Jan 2014 12:39:39 +0000 (14:39 +0200)]
e1000e: Fix compilation warning when !CONFIG_PM_SLEEP
Commit 7509963c703b (e1000e: Fix a compile flag mis-match for
suspend/resume) moved suspend and resume hooks to be available when
CONFIG_PM is set. However, it can be set even if CONFIG_PM_SLEEP is not set
causing following warnings to be emitted:
drivers/net/ethernet/intel/e1000e/netdev.c:6178:12: warning:
‘e1000_suspend’ defined but not used [-Wunused-function]
drivers/net/ethernet/intel/e1000e/netdev.c:6185:12: warning:
‘e1000_resume’ defined but not used [-Wunused-function]
To fix this make the hooks to be available only when CONFIG_PM_SLEEP is set
and remove CONFIG_PM wrapping from driver ops because this is already
handled by SET_SYSTEM_SLEEP_PM_OPS() and SET_RUNTIME_PM_OPS().
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Cc: Dave Ertman <davidx.m.ertman@intel.com> Cc: Aaron Brown <aaron.f.brown@intel.com> Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The above commit breaks the mapping type for Device memory because
pgprot_default already contains a Normal memory type. pgprot_default is
also not initialised early enough for earlyprintk resulting in an
inconsistent memory mapping with 64K PAGE_SIZE configuration.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Reported-by: Will Deacon <will.deacon@arm.com> Acked-by: Will Deacon <will.deacon@arm.com>
Robert Richter [Wed, 15 Jan 2014 14:57:29 +0000 (15:57 +0100)]
perf/x86/amd/ibs: Fix waking up from S3 for AMD family 10h
On AMD family 10h we see following error messages while waking up from
S3 for all non-boot CPUs leading to a failed IBS initialization:
Enabling non-boot CPUs ...
smpboot: Booting Node 0 Processor 1 APIC 0x1
[Firmware Bug]: cpu 1, try to use APIC500 (LVT offset 0) for vector 0x400, but the register is already in use for vector 0xf9 on another cpu
perf: IBS APIC setup failed on cpu #1
process: Switch to broadcast mode on CPU1
CPU1 is up
...
ACPI: Waking up from system sleep state S3
Reason for this is that during suspend the LVT offset for the IBS
vector gets lost and needs to be reinialized while resuming.
The offset is read from the IBSCTL msr. On family 10h the offset needs
to be 1 as offset 0 is used for the MCE threshold interrupt, but
firmware assings it for IBS to 0 too. The kernel needs to reprogram
the vector. The msr is a readonly node msr, but a new value can be
written via pci config space access. The reinitialization is
implemented for family 10h in setup_ibs_ctl() which is forced during
IBS setup.
This patch fixes IBS setup after waking up from S3 by adding
resume/supend hooks for the boot cpu which does the offset
reinitialization.
Marking it as stable to let distros pick up this fix.
Peter Zijlstra [Fri, 10 Jan 2014 20:06:03 +0000 (21:06 +0100)]
x86, mm, perf: Allow recursive faults from interrupts
Waiman managed to trigger a PMI while in a emulate_vsyscall() fault,
the PMI in turn managed to trigger a fault while obtaining a stack
trace. This triggered the sig_on_uaccess_error recursive fault logic
and killed the process dead.
Fix this by explicitly excluding interrupts from the recursive fault
logic.
Reported-and-Tested-by: Waiman Long <waiman.long@hp.com> Fixes: e00b12e64be9 ("perf/x86: Further optimize copy_from_user_nmi()") Cc: Aswin Chandramouleeswaran <aswin@hp.com> Cc: Scott J Norton <scott.norton@hp.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Andy Lutomirski <luto@amacapital.net> Cc: Arnaldo Carvalho de Melo <acme@ghostprotocols.net> Cc: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Peter Zijlstra <peterz@infradead.org> Link: http://lkml.kernel.org/r/20140110200603.GJ7572@laptop.programming.kicks-ass.net Signed-off-by: Ingo Molnar <mingo@kernel.org>
Linus Torvalds [Thu, 16 Jan 2014 01:33:21 +0000 (08:33 +0700)]
Merge branches 'sched-urgent-for-linus' and 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler and timer fixes from Ingo Molnar:
"Contains a fix for a scheduler bug that manifested itself as a 3D
performance regression and a crash fix for the ARM Cadence TTC clock
driver"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched: Calculate effective load even if local weight is 0
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
clocksource: cadence_ttc: Fix mutex taken inside interrupt context
Linus Torvalds [Thu, 16 Jan 2014 01:31:55 +0000 (08:31 +0700)]
Merge branch 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull locking fixes from Ingo Molnar:
"Two fixes from lockdep coverage of seqlocks, which fix deadlocks on
lockdep-enabled ARM systems"
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched_clock: Disable seqlock lockdep usage in sched_clock()
seqlock: Use raw_ prefix instead of _no_lockdep
Linus Torvalds [Thu, 16 Jan 2014 01:26:44 +0000 (08:26 +0700)]
Merge tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon fix from Guenter Roeck:
"Fix attribute length problem in coretemp driver"
* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (coretemp) Fix truncated name of alarm attributes
Eric Dumazet [Wed, 15 Jan 2014 14:50:07 +0000 (06:50 -0800)]
bpf: do not use reciprocal divide
At first Jakub Zawadzki noticed that some divisions by reciprocal_divide
were not correct. (off by one in some cases)
http://www.wireshark.org/~darkjames/reciprocal-buggy.c
He could also show this with BPF:
http://www.wireshark.org/~darkjames/set-and-dump-filter-k-bug.c
The reciprocal divide in linux kernel is not generic enough,
lets remove its use in BPF, as it is not worth the pain with
current cpus.
Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: Jakub Zawadzki <darkjames-ws@darkjames.pl> Cc: Mircea Gherzan <mgherzan@gmail.com> Cc: Daniel Borkmann <dxchgb@gmail.com> Cc: Hannes Frederic Sowa <hannes@stressinduktion.org> Cc: Matt Evans <matt@ozlabs.org> Cc: Martin Schwidefsky <schwidefsky@de.ibm.com> Cc: Heiko Carstens <heiko.carstens@de.ibm.com> Cc: David S. Miller <davem@davemloft.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Yuval Mintz [Wed, 15 Jan 2014 10:05:30 +0000 (12:05 +0200)]
bnx2x: Don't release PCI bars on shutdown
The bnx2x driver in its pci shutdown() callback releases its pci bars (in the
same manner it does during its pci remove() callback).
During a system reboot while VFs are enabled, its possible for the VF's remove
to be called (as a result of pci_disable_sriov()) after its shutdown callback
has already finished running; This will cause a paging request fault as the VF
tries to access the pci bar which it has previously released, crashing the
system.
This patch further differentiates the shutdown and remove callbacks, preventing the
pci release procedures from being called during shutdown.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com> Signed-off-by: Ariel Elior <ariele@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
rhine_reset_task() misses to disable the tx scheduler upon reset,
this can lead to a crash if work is still scheduled while we're resetting
the tx queue.
Fixes:
[ 93.591707] BUG: unable to handle kernel NULL pointer dereference at 0000004c
[ 93.595514] IP: [<c119d10d>] rhine_napipoll+0x491/0x6
Signed-off-by: Richard Weinberger <richard@nod.at> Signed-off-by: David S. Miller <davem@davemloft.net>
Batman-adv prepends a full ethernet header in addition to its own
header. This has to be reflected in the MTU calculation, especially
since the value is used to set dev->hard_header_len.
Reported-by: cmsv <cmsv@wirelesspt.net> Reported-by: Martin Hundebøll <martin@hundeboll.net> Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch> Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Andrew Jones [Wed, 15 Jan 2014 12:39:59 +0000 (13:39 +0100)]
kvm: x86: fix apic_base enable check
Commit e66d2ae7c67bd moved the assignment
vcpu->arch.apic_base = value above a condition with
(vcpu->arch.apic_base ^ value), causing that check
to always fail. Use old_value, vcpu->arch.apic_base's
old value, in the condition instead.
Signed-off-by: Andrew Jones <drjones@redhat.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Linus Torvalds [Wed, 15 Jan 2014 08:42:11 +0000 (15:42 +0700)]
Merge branch 'akpm' (incoming from Andrew)
Merge patches from Andrew Morton:
"Six fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
lib/percpu_counter.c: fix __percpu_counter_add()
crash_dump: fix compilation error (on MIPS at least)
mm: fix crash when using XFS on loopback
MIPS: fix blast_icache32 on loongson2
MIPS: fix case mismatch in local_r4k_flush_icache_range()
nilfs2: fix segctor bug that causes file system corruption
Linus Torvalds [Wed, 15 Jan 2014 08:07:36 +0000 (15:07 +0700)]
Merge tag 'md/3.13-fixes' of git://neil.brown.name/md
Pull late md fixes from Neil Brown:
"Half a dozen md bug fixes.
All of these fix real bugs the people have hit, and are tagged for
-stable. Sorry they are late .... Christmas holidays and all that.
Hopefully they can still squeak into 3.13"
* tag 'md/3.13-fixes' of git://neil.brown.name/md:
md: fix problem when adding device to read-only array with bitmap.
md/raid10: fix bug when raid10 recovery fails to recover a block.
md/raid5: fix a recently broken BUG_ON().
md/raid1: fix request counting bug in new 'barrier' code.
md/raid10: fix two bugs in handling of known-bad-blocks.
md/raid5: Fix possible confusion when multiple write errors occur.
Linus Torvalds [Wed, 15 Jan 2014 08:06:14 +0000 (15:06 +0700)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"One nouveau regression fix on older cards, i915 black screen fixes,
and a revert for a strange G33 intel problem"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/nouveau: fix null ptr dereferences on some boards
Revert "drm: copy mode type in drm_mode_connector_list_update()"
drm/i915/bdw: make sure south port interrupts are enabled properly v2
drm/i915: Don't grab crtc mutexes in intel_modeset_gem_init()
drm/i915: fix DDI PLLs HW state readout code
Ming Lei [Wed, 15 Jan 2014 01:56:42 +0000 (17:56 -0800)]
lib/percpu_counter.c: fix __percpu_counter_add()
__percpu_counter_add() may be called in softirq/hardirq handler (such
as, blk_mq_queue_exit() is typically called in hardirq/softirq handler),
so we need to call this_cpu_add()(irq safe helper) to update percpu
counter, otherwise counts may be lost.
This fixes the problem that 'rmmod null_blk' hangs in blk_cleanup_queue()
because of miscounting of request_queue->mq_usage_counter.
This patch is the v1 of previous one of "lib/percpu_counter.c:
disable local irq when updating percpu couter", and takes Andrew's
approach which may be more efficient for ARCHs(x86, s390) that
have optimized this_cpu_add().
Signed-off-by: Ming Lei <tom.leiming@gmail.com> Cc: Paul Gortmaker <paul.gortmaker@windriver.com> Cc: Shaohua Li <shli@fusionio.com> Cc: Jens Axboe <axboe@kernel.dk> Cc: Fan Du <fan.du@windriver.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mikulas Patocka [Wed, 15 Jan 2014 01:56:40 +0000 (17:56 -0800)]
mm: fix crash when using XFS on loopback
Commit 8456a648cf44 ("slab: use struct page for slab management") causes
a crash in the LVM2 testsuite on PA-RISC (the crashing test is
fsadm.sh). The testsuite doesn't crash on 3.12, crashes on 3.13-rc1 and
later.
Kernel panic - not syncing: Bad Address (null pointer deref?)
Commit 8456a648cf44 changes the page structure so that the slab
subsystem reuses the page->mapping field.
The crash happens in the following way:
* XFS allocates some memory from slab and issues a bio to read data
into it.
* the bio is sent to the loopback device.
* lo_receive creates an actor and calls splice_direct_to_actor.
* lo_splice_actor copies data to the target page.
* lo_splice_actor calls flush_dcache_page because the page may be
mapped by userspace. In that case we need to flush the kernel cache.
* flush_dcache_page asks for the list of userspace mappings, however
that page->mapping field is reused by the slab subsystem for a
different purpose. This causes the crash.
Note that other architectures without coherent caches (sparc, arm, mips)
also call page_mapping from flush_dcache_page, so they may crash in the
same way.
This patch fixes this bug by testing if the page is a slab page in
page_mapping and returning NULL if it is.
The patch also fixes VM_BUG_ON(PageSlab(page)) that could happen in
earlier kernels in the same scenario on architectures without cache
coherence when CONFIG_DEBUG_VM is enabled - so it should be backported
to stable kernels.
In the old kernels, the function page_mapping is placed in
include/linux/mm.h, so you should modify the patch accordingly when
backporting it.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com> Cc: John David Anglin <dave.anglin@bell.net>] Cc: Andi Kleen <ak@linux.intel.com> Cc: Christoph Lameter <cl@linux.com> Acked-by: Pekka Enberg <penberg@kernel.org> Reviewed-by: Joonsoo Kim <iamjoonsoo.kim@lge.com> Cc: Helge Deller <deller@gmx.de> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Aaro Koskinen [Wed, 15 Jan 2014 01:56:38 +0000 (17:56 -0800)]
MIPS: fix blast_icache32 on loongson2
Commit 14bd8c082016 ("MIPS: Loongson: Get rid of Loongson 2 #ifdefery
all over arch/mips") failed to add Loongson2 specific blast_icache32
functions. Fix that.
The patch fixes the following crash seen with 3.13-rc1:
Huacai Chen [Wed, 15 Jan 2014 01:56:37 +0000 (17:56 -0800)]
MIPS: fix case mismatch in local_r4k_flush_icache_range()
Currently, Loongson-2 call protected_blast_icache_range() and others
call protected_loongson23_blast_icache_range(), but I think the correct
behavior should be the opposite. BTW, Loongson-3's cache-ops is
compatible with MIPS64, but not compatible with Loongson-2. So, rename
xxx_loongson23_yyy things to xxx_loongson2_yyy.
The patch fixes early boot hang with 3.13-rc1, introduced in commit 14bd8c082016 ("MIPS: Loongson: Get rid of Loongson 2 #ifdefery all over
arch/mips").
Signed-off-by: Huacai Chen <chenhc@lemote.com> Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi> Reviewed-by: Aurelien Jarno <aurelien@aurel32.net> Acked-by: John Crispin <blogic@openwrt.org> Cc: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andreas Rohner [Wed, 15 Jan 2014 01:56:36 +0000 (17:56 -0800)]
nilfs2: fix segctor bug that causes file system corruption
There is a bug in the function nilfs_segctor_collect, which results in
active data being written to a segment, that is marked as clean. It is
possible, that this segment is selected for a later segment
construction, whereby the old data is overwritten.
The problem shows itself with the following kernel log message:
nilfs_sufile_do_cancel_free: segment 6533 must be clean
Usually a few hours later the file system gets corrupted:
The issue can be reproduced with a file system that is nearly full and
with the cleaner running, while some IO intensive task is running.
Although it is quite hard to reproduce.
This is what happens:
1. The cleaner starts the segment construction
2. nilfs_segctor_collect is called
3. sc_stage is on NILFS_ST_SUFILE and segments are freed
4. sc_stage is on NILFS_ST_DAT current segment is full
5. nilfs_segctor_extend_segments is called, which
allocates a new segment
6. The new segment is one of the segments freed in step 3
7. nilfs_sufile_cancel_freev is called and produces an error message
8. Loop around and the collection starts again
9. sc_stage is on NILFS_ST_SUFILE and segments are freed
including the newly allocated segment, which will contain active
data and can be allocated at a later time
10. A few hours later another segment construction allocates the
segment and causes file system corruption
This can be prevented by simply reordering the statements. If
nilfs_sufile_cancel_freev is called before nilfs_segctor_extend_segments
the freed segments are marked as dirty and cannot be allocated any more.
Signed-off-by: Andreas Rohner <andreas.rohner@gmx.net> Reviewed-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp> Tested-by: Andreas Rohner <andreas.rohner@gmx.net> Signed-off-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ingo Molnar [Wed, 15 Jan 2014 06:39:30 +0000 (07:39 +0100)]
Merge branch 'clockevents/3.13-fixes' of git://git.linaro.org/people/daniel.lezcano/linux into timers/urgent
Pull clock driver fix from Daniel Lezcano:
" * Soren Brinkmann fixed the cadence_ttc driver where a call to
clk_get_rate happens in an interrupt context. More precisely in an IPI
when the broadcast timer is initialized for each cpu in the cpuidle
driver. "
net: avoid reference counter overflows on fib_rules in multicast forwarding
Bob Falken reported that after 4G packets, multicast forwarding stopped
working. This was because of a rule reference counter overflow which
freed the rule as soon as the overflow happend.
This patch solves this by adding the FIB_LOOKUP_NOREF flag to
fib_rules_lookup calls. This is safe even from non-rcu locked sections
as in this case the flag only implies not taking a reference to the rule,
which we don't need at all.
Rules only hold references to the namespace, which are guaranteed to be
available during the call of the non-rcu protected function reg_vif_xmit
because of the interface reference which itself holds a reference to
the net namespace.
Fixes: f0ad0860d01e47 ("ipv4: ipmr: support multiple tables") Fixes: d1db275dd3f6e4 ("ipv6: ip6mr: support multiple tables") Reported-by: Bob Falken <NetFestivalHaveFun@gmx.com> Cc: Patrick McHardy <kaber@trash.net> Cc: Thomas Graf <tgraf@suug.ch> Cc: Julian Anastasov <ja@ssi.bg> Cc: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / thirdparty / kernel / stable.git / log
