thinkpad_acpi was reporting 2 fans on a ThinkPad T14s gen 1, even though
the laptop has only 1 fan.
The second, not present fan always reads 65535 (-1 in 16 bit signed),
ignore fans which report 65535 to avoid reporting the non present fan.
Signed-off-by: Jelle van der Waa <jvanderwaa@redhat.com> Link: https://lore.kernel.org/r/20221019194751.5392-1-jvanderwaa@redhat.com Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Lenovo Thinkbook 14+ 2022 (ThinkBook 14 G4+ ARA) uses Ryzen
6000 processor, and has the same microphone problem as other
ThinkPads with AMD Ryzen 6000 series CPUs, which has been
listed in https://bugzilla.kernel.org/show_bug.cgi?id=216267.
Adding 21D0 to quirks table solves this microphone problem
for ThinkBook 14 G4+ ARA.
Don't use the test-specific header files as source files to force a
target dependency, as clang will complain if more than one source file
is used for a compile command with a single '-o' flag.
Use the proper Makefile variables instead as defined in
tools/testing/selftests/lib.mk.
Line In Bypass control is used as Master Capture at the moment
this is completely incorrect.
Current control routed to Mixer instead of ADC, thus can't affect
Capture path. ADC control shall be used instead.
ADC volume control parameters are different, so the patch fixes that
as well. Manual says (16.6.3.2 Programmable input attenuation amplifier:
PGATM) that gain varies in range 0dB..22.5dB with 1.5dB step.
DAC volume control is the Master Playback Volume at the moment
and it reports wrong levels in alsamixer and other alsa apps.
The patch fixes that, as stated in manual on the jz4725b SoC
(16.6.3.4 Programmable attenuation: GOD) the ctl range varies
from -22.5dB to 0dB with 1.5dB step.
According to documentation, the 64K erase opcode is located in VSCC
range [16:23] instead of [8:15].
Use the proper value to shift the mask over the correct range.
In wm8962 driver, the WM8962_ADDITIONAL_CONTROL_4 is used as a volatile
register, but this register mixes a bunch of volatile status bits and a
bunch of non-volatile control bits. The dapm widgets TEMP_HP and
TEMP_SPK leverages the control bits in this register. After the wm8962
probe, the regmap will bet set to cache only mode, then a read error
like below would be triggered when trying to read the initial power
state of the dapm widgets TEMP_HP and TEMP_SPK.
wm8962 0-001a: ASoC: error at soc_component_read_no_lock
on wm8962.0-001a: -16
In order to fix this issue, we add event handler to actually power
up/down these widgets. With this change, we also need to explicitly
power off these widgets in the wm8962 probe since they are enabled
by default.
Signed-off-by: Xiaolei Wang <xiaolei.wang@windriver.com> Tested-by: Adam Ford <aford173@gmail.com> Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com> Link: https://lore.kernel.org/r/20221010092014.2229246-1-xiaolei.wang@windriver.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
It would be better to keep the pm_runtime enables before the
IRQ and component stuff. Both of those could start triggering
PM runtime events.
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Link: https://lore.kernel.org/r/20221008140522.134912-1-zhangqilong3@huawei.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Return value should be updated to zero in combined sequence routine
if transfer is completed successfully. Currently it holds timeout value
resulting in errors.
In adreno_unbind, we should clean up gpu device's drvdata to avoid
accessing a stale pointer during system suspend. Also, check for NULL
ptr in both system suspend/resume callbacks.
With use_codeword_fixup enabled, any return from
mtd_device_parse_register gets overwritten. Aside from the clear bug, this
is also problematic as a parser can EPROBE_DEFER and because this is not
correctly handled, the nand is never rescanned later in the bootup
process.
An example of this problem is when smem requires additional time to be
probed and nandc use qcomsmempart as parser. Parser will return
EPROBE_DEFER but in the current code this ret gets overwritten by
qcom_nand_host_parse_boot_partitions and qcom_nand_host_init_and_register
return 0.
Correctly handle the return code from mtd_device_parse_register so that
any error from this function is not ignored.
Fixes: 862bdedd7f4b ("mtd: nand: raw: qcom_nandc: add support for unprotected spare data pages") Cc: stable@vger.kernel.org # v6.0+ Signed-off-by: Christian Marangi <ansuelsmth@gmail.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20221021165304.19991-1-ansuelsmth@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The latest fix for the non-contiguous memalloc helper changed the
allocation method for a non-IOMMU system to use only the fallback
allocator. This should have worked, but it caused a problem sometimes
when too many non-contiguous pages are allocated that can't be treated
by HD-audio controller.
As a quirk workaround, go back to the original strategy: use
dma_alloc_noncontiguous() at first, and apply the fallback only when
it fails, but only for non-IOMMU case.
We'll need a better fix in the fallback code as well, but this
workaround should paper over most cases.
migrate_vma_setup shows below warning because we don't hold another
process mm mmap_lock. We should use current vmf->vma->vm_mm instead, the
caller already hold current mmap lock inside CPU page fault handler.
Fixes: e1f84eef313f ("drm/amdkfd: handle CPU fault on COW mapping") Signed-off-by: Philip Yang <Philip.Yang@amd.com> Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The iterator can not be greater than ATC_MAX_DSCR_TRIALS, as the for loop
will stop when i == ATC_MAX_DSCR_TRIALS. While here, use the common "i"
name for the iterator.
at_hdmac uses __raw_writel for register writes. In the absence of a
barrier, the CPU may reorder the register operations.
Introduce a write memory barrier so that the CPU does not reorder the
channel enable, thus the start of the transfer, without making sure that
all the pre-required register fields are already written.
In case the controller detected an error, the code took the chance to move
all the queued (submitted) descriptors to the active (issued) list. This
was wrong as if there were any descriptors in the submitted list they were
moved to the issued list without actually issuing them to the controller,
thus a completion could be raised without even fireing the descriptor.
As it was before, the descriptor was issued to the hardware without adding
it to the active (issued) list. This could result in a completion of other
descriptor, or/and in the descriptor never being completed.
The tasklet (atc_advance_work()) did not held the channel lock when
retrieving the first active descriptor, causing concurrency problems if
issue_pending() was called in between. If issue_pending() was called
exactly after the lock was released in the tasklet (atc_advance_work()),
atc_chain_complete() could complete a descriptor for which the controller
has not yet raised an interrupt.
There's no need to hold the channel lock when freeing the memset buf, as
the operation has already completed. Free the memset buf without holding
the channel lock.
The descriptor was added to the free_list before calling the callback,
which could result in reissuing of the same descriptor and calling of a
single callback for both. Move the decriptor to the free list after the
callback is invoked.
atc_complete_all() had concurrency bugs, thus remove it:
1/ atc_complete_all() in its entirety was buggy, as when the atchan->queue
list (the one that contains descriptors that are not yet issued to the
hardware) contained descriptors, it fired just the first from the
atchan->queue, but moved all the desc from atchan->queue to
atchan->active_list and considered them all as fired. This could result in
calling the completion of a descriptor that was not yet issued to the
hardware.
2/ when in tasklet at atc_advance_work() time, atchan->active_list was
queried without holding the lock of the chan. This can result in
atchan->active_list concurrency problems between the tasklet and
issue_pending().
Now that the complete callback call was removed from
device_terminate_all(), we can protect the atchan->status with the channel
lock. The atomic bitops on atchan->status do not substitute proper locking
on the status, as one could still modify the status after the lock was
dropped in atc_terminate_all() but before the atomic bitops were executed.
The method was wrong because it violated the dmaengine API. For aborted
transfers the complete callback should not be called. Fix the behavior and
do not call the complete callback on device_terminate_all.
Multiple calls to atc_issue_pending() could result in a premature
completion of a descriptor from the atchan->active list, as the method
always completed the first active descriptor from the list. Instead,
issue_pending() should just take the first transaction descriptor from the
pending queue, move it to active_list and start the transfer.
Cyclic channels must too call issue_pending in order to start a transfer.
Start the transfer in issue_pending regardless of the type of channel.
This wrongly worked before, because in the past the transfer was started
at tx_submit level when only a desc in the transfer list.
tx_submit is supposed to push the current transaction descriptor to a
pending queue, waiting for issue_pending() to be called. issue_pending()
must start the transfer, not tx_submit(), thus remove atc_dostart() from
atc_tx_submit(). Clients of at_xdmac that assume that tx_submit() starts
the transfer must be updated and call dma_async_issue_pending() if they
miss to call it.
The vdbg print was moved to after the lock is released. It is desirable to
do the prints without the lock held if possible, and because the if
statement disappears there's no reason why to do the print while holding
the lock.
Those hardware registers are all of 32 bits, while dma_addr_t ca be of
type u64 or u32 depending on CONFIG_ARCH_DMA_ADDR_T_64BIT. Force u32 to
comply with what the hardware expects.
In commit a6d190f8c767 ("can: skb: drop tx skb if in listen only
mode") the priv->ctrlmode element is read even on virtual CAN
interfaces that do not create the struct can_priv at startup. This
out-of-bounds read may lead to CAN frame drops for virtual CAN
interfaces like vcan and vxcan.
This patch mainly reverts the original commit and adds a new helper
for CAN interface drivers that provide the required information in
struct can_priv.
Fixes: a6d190f8c767 ("can: skb: drop tx skb if in listen only mode") Reported-by: Dariusz Stojaczyk <Dariusz.Stojaczyk@opensynergy.com> Cc: Vincent Mailhol <mailhol.vincent@wanadoo.fr> Cc: Max Staudt <max@enpas.org> Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net> Acked-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr> Link: https://lore.kernel.org/all/20221102095431.36831-1-socketcan@hartkopp.net Cc: stable@vger.kernel.org # 6.0.x
[mkl: patch pch_can, too] Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is error-prone that code after vmexit cannot access percpu data
because GSBASE has not been restored yet. It forces MSR_IA32_SPEC_CTRL
save/restore to happen very late, after the predictor untraining
sequence, and it gets in the way of return stack depth tracking
(a retbleed mitigation that is in linux-next as of 2022-11-09).
As a first step towards fixing that, move the VMCB VMSAVE/VMLOAD to
assembly, essentially undoing commit fb0c4a4fee5a ("KVM: SVM: move
VMLOAD/VMSAVE to C code", 2021-03-15). The reason for that commit was
that it made it simpler to use a different VMCB for VMLOAD/VMSAVE versus
VMRUN; but that is not a big hassle anymore thanks to the kvm-asm-offsets
machinery and other related cleanups.
The idea on how to number the exception tables is stolen from
a prototype patch by Peter Zijlstra.
Continue moving accesses to struct vcpu_svm to vmenter.S. Reducing the
number of arguments limits the chance of mistakes due to different
registers used for argument passing in 32- and 64-bit ABIs; pushing the
VMCB argument and almost immediately popping it into a different
register looks pretty weird.
32-bit ABI is not a concern for __svm_sev_es_vcpu_run() which is 64-bit
only; however, it will soon need @svm to save/restore SPEC_CTRL so stay
consistent with __svm_vcpu_run() and let them share the same prototype.
Explicitly print the VMSA dump at KERN_DEBUG log level, KERN_CONT uses
KERNEL_DEFAULT if the previous log line has a newline, i.e. if there's
nothing to continuing, and as a result the VMSA gets dumped when it
shouldn't.
The KERN_CONT documentation says it defaults back to KERNL_DEFAULT if the
previous log line has a newline. So switch from KERN_CONT to
print_hex_dump_debug().
Jarkko pointed this out in reference to the original patch. See:
https://lore.kernel.org/all/YuPMeWX4uuR1Tz3M@kernel.org/
print_hex_dump(KERN_DEBUG, ...) was pointed out there, but
print_hex_dump_debug() should similar.
Fixes: 6fac42f127b8 ("KVM: SVM: Dump Virtual Machine Save Area (VMSA) to klog") Signed-off-by: Peter Gonda <pgonda@google.com> Reviewed-by: Sean Christopherson <seanjc@google.com> Cc: Jarkko Sakkinen <jarkko@kernel.org> Cc: Harald Hoyer <harald@profian.com> Cc: Paolo Bonzini <pbonzini@redhat.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@redhat.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Dave Hansen <dave.hansen@linux.intel.com> Cc: x86@kernel.org Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: kvm@vger.kernel.org Cc: linux-kernel@vger.kernel.org Cc: stable@vger.kernel.org
Message-Id: <20221104142220.469452-1-pgonda@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
32-bit ABI uses RAX/RCX/RDX as its argument registers, so they are in
the way of instructions that hardcode their operands such as RDMSR/WRMSR
or VMLOAD/VMRUN/VMSAVE.
In preparation for moving vmload/vmsave to __svm_vcpu_run(), keep
the pointer to the struct vcpu_svm in %rdi. In particular, it is now
possible to load svm->vmcb01.pa in %rax without clobbering the struct
vcpu_svm pointer.
This already removes an ugly #include "" from asm-offsets.c, but
especially it avoids a future error when trying to define asm-offsets
for KVM's svm/svm.h header.
This would not work for kernel/asm-offsets.c, because svm/svm.h
includes kvm_cache_regs.h which is not in the include path when
compiling asm-offsets.c. The problem is not there if the .c file is
in arch/x86/kvm.
Suggested-by: Sean Christopherson <seanjc@google.com> Cc: stable@vger.kernel.org Fixes: a149180fbcf3 ("x86: Add magic AMD return-thunk") Reviewed-by: Sean Christopherson <seanjc@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SDM lists an architectural MSR IA32_CORE_CAPABILITIES (0xCF)
that limits the theoretical maximum value of the Intel GP PMC MSRs
allocated at 0xC1 to 14; likewise the Intel April 2022 SDM adds
IA32_OVERCLOCKING_STATUS at 0x195 which limits the number of event
selection MSRs to 15 (0x186-0x194).
Limiting the maximum number of counters to 14 or 18 based on the currently
allocated MSRs is clearly fragile, and it seems likely that Intel will
even place PMCs 8-15 at a completely different range of MSR indices.
So stop at the maximum number of GP PMCs supported today on Intel
processors.
There are some machines, like Intel P4 with non Architectural PMU, that
may indeed have 18 counters, but those counters are in a completely
different MSR address range and are not supported by KVM.
Cc: Vitaly Kuznetsov <vkuznets@redhat.com> Cc: stable@vger.kernel.org Fixes: cf05a67b68b8 ("KVM: x86: omit "impossible" pmu MSRs from MSR list") Suggested-by: Jim Mattson <jmattson@google.com> Signed-off-by: Like Xu <likexu@tencent.com> Reviewed-by: Jim Mattson <jmattson@google.com>
Message-Id: <20220919091008.60695-1-likexu@tencent.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When zapping a GFN range, pass 0 => ALL_ONES for the to-be-invalidated
range to effectively block all page faults while the zap is in-progress.
The invalidation helpers take a host virtual address, whereas zapping a
GFN obviously provides a guest physical address and with the wrong unit
of measurement (frame vs. byte).
Alternatively, KVM could walk all memslots to get the associated HVAs,
but thanks to SMM, that would require multiple lookups. And practically
speaking, kvm_zap_gfn_range() usage is quite rare and not a hot path,
e.g. MTRR and CR0.CD are almost guaranteed to be done only on vCPU0
during boot, and APICv inhibits are similarly infrequent operations.
When introducing support for R-Car V3U, which has 8 instead of 2
channels, the ECC error bitmask was extended to take into account the
extra channels, but rcar_canfd_global_error() was not updated to act
upon the extra bits.
Replace the RCANFD_GERFL_EEF[01] macros by a new macro that takes the
channel number, fixing R-Car V3U while simplifying the code.
Fixes: 45721c406dcf50d4 ("can: rcar_canfd: Add support for r8a779a0 SoC") Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com> Link: https://lore.kernel.org/all/4edb2ea46cc64d0532a08a924179827481e14b4f.1666951503.git.geert+renesas@glider.be Cc: stable@vger.kernel.org Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In commit 4b7fe92c0690 ("can: isotp: add local echo tx processing for
consecutive frames") the data flow for consecutive frames (CF) has been
reworked to improve the reliability of long data transfers.
This rework did not touch the transmission and the tx state changes of
single frame (SF) transfers which likely led to the WARN in the
isotp_tx_timer_handler() catching a wrong tx state. This patch makes use
of the improved frame processing for SF frames and sets the ISOTP_SENDING
state in isotp_sendmsg() within the cmpxchg() condition handling.
A review of the state machine and the timer handling additionally revealed
a missing echo timeout handling in the case of the burst mode in
isotp_rcv_echo() and removes a potential timer configuration uncertainty
in isotp_rcv_fc() when the receiver requests consecutive frames.
The read access to struct canxl_frame::len inside of a j1939 created
skbuff revealed a missing initialization of reserved and later filled
elements in struct can_frame.
This patch initializes the 8 byte CAN header with zero.
mfill_atomic_install_pte() checks page->mapping to detect whether one page
is used in the page cache. However as pointed out by Matthew, the page
can logically be a tail page rather than always the head in the case of
uffd minor mode with UFFDIO_CONTINUE. It means we could wrongly install
one pte with shmem thp tail page assuming it's an anonymous page.
It's not that clear even for anonymous page, since normally anonymous
pages also have page->mapping being setup with the anon vma. It's safe
here only because the only such caller to mfill_atomic_install_pte() is
always passing in a newly allocated page (mcopy_atomic_pte()), whose
page->mapping is not yet setup. However that's not extremely obvious
either.
For either of above, use page_mapping() instead.
Link: https://lkml.kernel.org/r/Y2K+y7wnhC4vbnP2@x1n Fixes: 153132571f02 ("userfaultfd/shmem: support UFFDIO_CONTINUE for shmem") Signed-off-by: Peter Xu <peterx@redhat.com> Reported-by: Matthew Wilcox <willy@infradead.org> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Hugh Dickins <hughd@google.com> Cc: Axel Rasmussen <axelrasmussen@google.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
virtio_pmem use devm_memremap_pages() to map the device memory. By
default this memory is mapped as encrypted with SEV. Guest reboot changes
the current encryption key and guest no longer properly decrypts the FSDAX
device meta data.
Mark the corresponding device memory region for FSDAX devices (mapped with
memremap_pages) as decrypted to retain the persistent memory property.
Link: https://lkml.kernel.org/r/20221102160728.3184016-1-pankaj.gupta@amd.com Fixes: b7b3c01b19159 ("mm/memremap_pages: support multiple ranges per invocation") Signed-off-by: Pankaj Gupta <pankaj.gupta@amd.com> Cc: Dan Williams <dan.j.williams@intel.com> Cc: Tom Lendacky <thomas.lendacky@amd.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A user could write a name of a file under 'damon/' debugfs directory,
which is not a user-created context, to 'rm_contexts' file. In the case,
'dbgfs_rm_context()' just assumes it's the valid DAMON context directory
only if a file of the name exist. As a result, invalid memory access
could happen as below. Fix the bug by checking if the given input is for
a directory. This check can filter out non-context inputs because
directories under 'damon/' debugfs directory can be created via only
'mk_contexts' file.
When the idxd_user_drv driver is bound to a Work Queue (WQ) device
without IOMMU or with IOMMU Passthrough without Shared Virtual
Addressing (SVA), the application gains direct access to physical
memory via the device by programming physical address to a submitted
descriptor. This allows direct userspace read and write access to
arbitrary physical memory. This is inconsistent with the security
goals of a good kernel API.
Unlike vfio_pci driver, the IDXD char device driver does not provide any
ways to pin user pages and translate the address from user VA to IOVA or
PA without IOMMU SVA. Therefore the application has no way to instruct the
device to perform DMA function. This makes the char device not usable for
normal application usage.
Since user type WQ without SVA cannot be used for normal application usage
and presents the security issue, bind idxd_user_drv driver and enable user
type WQ only when SVA is enabled (i.e. user PASID is enabled).
Fixes: 448c3de8ac83 ("dmaengine: idxd: create user driver for wq 'device'") Cc: stable@vger.kernel.org Suggested-by: Arjan Van De Ven <arjan.van.de.ven@intel.com> Signed-off-by: Fenghua Yu <fenghua.yu@intel.com> Reviewed-by: Dave Jiang <dave.jiang@intel.com> Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com> Link: https://lore.kernel.org/r/20221014222541.3912195-1-fenghua.yu@intel.com Signed-off-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The kernel test robot reported build failures with a 'randconfig' on s390:
>> mm/hugetlb_vmemmap.c:421:11: error: a function declaration without a
prototype is deprecated in all versions of C [-Werror,-Wstrict-prototypes]
core_param(hugetlb_free_vmemmap, vmemmap_optimize_enabled, bool, 0);
^
Recently pud_huge() got aware of non-present entry by commit 3a194f3f8ad0
("mm/hugetlb: make pud_huge() and follow_huge_pud() aware of non-present
pud entry") to handle some special states of gigantic page. However, it's
overlooked that pud_none() always returns false when running with 2-level
paging, and as a result pud_huge() can return true pointlessly.
Introduce "#if CONFIG_PGTABLE_LEVELS > 2" to pud_huge() to deal with this.
Link: https://lkml.kernel.org/r/20221107021010.2449306-1-naoya.horiguchi@linux.dev Fixes: 3a194f3f8ad0 ("mm/hugetlb: make pud_huge() and follow_huge_pud() aware of non-present pud entry") Signed-off-by: Naoya Horiguchi <naoya.horiguchi@nec.com> Reported-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Tested-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Miaohe Lin <linmiaohe@huawei.com> Cc: David Hildenbrand <david@redhat.com> Cc: Liu Shixin <liushixin2@huawei.com> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Muchun Song <songmuchun@bytedance.com> Cc: Oscar Salvador <osalvador@suse.de> Cc: Yang Shi <shy828301@gmail.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@redhat.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Dave Hansen <dave.hansen@linux.intel.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
loop0: detected capacity change from 0 to 2048
==================================================================
BUG: KASAN: slab-out-of-bounds in udf_find_entry+0x8a5/0x14f0
fs/udf/namei.c:253
Write of size 105 at addr ffff8880123ff896 by task syz-executor323/3610
The buggy address belongs to the object at ffff8880123ff800
which belongs to the cache kmalloc-256 of size 256
The buggy address is located 150 bytes inside of
256-byte region [ffff8880123ff800, ffff8880123ff900)
The buggy address belongs to the physical page:
page:ffffea000048ff80 refcount:1 mapcount:0 mapping:0000000000000000
index:0x0 pfn:0x123fe
head:ffffea000048ff80 order:1 compound_mapcount:0 compound_pincount:0
flags: 0xfff00000010200(slab|head|node=0|zone=1|lastcpupid=0x7ff)
raw: 00fff00000010200ffffea00004b8500dead000000000003ffff888012041b40
raw: 0000000000000000000000008010001000000001ffffffff0000000000000000
page dumped because: kasan: bad access detected
page_owner tracks the page as allocated
page last allocated via order 0, migratetype Unmovable, gfp_mask 0x0(),
pid 1, tgid 1 (swapper/0), ts 1841222404, free_ts 0
create_dummy_stack mm/page_owner.c:67 [inline]
register_early_stack+0x77/0xd0 mm/page_owner.c:83
init_page_owner+0x3a/0x731 mm/page_owner.c:93
kernel_init_freeable+0x41c/0x5d5 init/main.c:1629
kernel_init+0x19/0x2b0 init/main.c:1519
page_owner free stack trace missing
Memory state around the buggy address: ffff8880123ff780: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc ffff8880123ff800: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>ffff8880123ff880: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 06
^ ffff8880123ff900: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc ffff8880123ff980: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
==================================================================
Fix this by changing the memory size allocated for copy_name from
UDF_NAME_LEN(254) to UDF_NAME_LEN_CS0(255), because the total length
(lfi) of subsequent memcpy can be up to 255.
CC: stable@vger.kernel.org Reported-by: syzbot+69c9fdccc6dd08961d34@syzkaller.appspotmail.com Fixes: 066b9cded00b ("udf: Use separate buffer for copying split names") Signed-off-by: ZhangPeng <zhangpeng362@huawei.com> Signed-off-by: Jan Kara <jack@suse.cz> Link: https://lore.kernel.org/r/20221109013542.442790-1-zhangpeng362@huawei.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[[ NOTE: this is completely untested by the author, but included solely
because, as noted in commit df57d73276b8 ("mmc: sdhci-pci: Fix
SDHCI_RESET_ALL for CQHCI for Intel GLK-based controllers"), "other
drivers using CQHCI might benefit from a similar change, if they
also have CQHCI reset by SDHCI_RESET_ALL." We've now seen the same
bug on at least MSM, Arasan, and Intel hardware. ]]
SDHCI_RESET_ALL resets will reset the hardware CQE state, but we aren't
tracking that properly in software. When out of sync, we may trigger
various timeouts.
It's not typical to perform resets while CQE is enabled, but this may
occur in some suspend or error recovery scenarios.
Include this fix by way of the new sdhci_and_cqhci_reset() helper.
This patch depends on (and should not compile without) the patch
entitled "mmc: cqhci: Provide helper for resetting both SDHCI and
CQHCI".
Move am65_cpsw_nuss_phylink_cleanup() call to after
am65_cpsw_nuss_cleanup_ndev() so phylink is still valid
to prevent the below Segmentation fault on module remove when
first slave link is up.
Commit fc64623637da ("phy: qcom-qmp-combo,usb: add support for separate
PCS_USB region") started treating the PCS_USB registers as potentially
separate from the PCS registers but used the wrong base when no PCS_USB
offset has been provided.
Fix the PCS_USB base used at runtime resume to prevent dereferencing a
NULL pointer on platforms that do not provide a PCS_USB offset (e.g.
SC7180).
Fixes: fc64623637da ("phy: qcom-qmp-combo,usb: add support for separate PCS_USB region") Cc: stable@vger.kernel.org # 5.20 Signed-off-by: Johan Hovold <johan+linaro@kernel.org> Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Reviewed-by: Andrew Halaney <ahalaney@redhat.com> Link: https://lore.kernel.org/r/20221026162116.26462-1-johan+linaro@kernel.org Signed-off-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We already check if the chosen starting offset for the buffer IDs fit
within an unsigned short, as 65535 is the maximum value for a provided
buffer. But if the caller asks to add N buffers at offset M, and M + N
would exceed the size of the unsigned short, we simply add buffers with
wrapping around the ID.
This is not necessarily a bug and could in fact be a valid use case, but
it seems confusing and inconsistent with the initial check for starting
offset. Let's check for wrap consistently, and error the addition if we
do need to wrap.
When performing seeding on a zoned filesystem it is necessary to
initialize each zoned device's btrfs_zoned_device_info structure,
otherwise mounting the filesystem will cause a NULL pointer dereference.
This was uncovered by fstests' testcase btrfs/163.
CC: stable@vger.kernel.org # 5.15+ Signed-off-by: Johannes Thumshirn <johannes.thumshirn@wdc.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
assertion failed: (args->devid != (u64)-1) || args->missing, in fs/btrfs/volumes.c:6921
This can be triggered when we set devid to (u64)-1 by ioctl. In this
case, the match of devid will be skipped and the match of device may
succeed incorrectly.
Patch 562d7b1512f7 introduced this function which is used to match device.
This function contains two matching scenarios, we can distinguish them by
checking the value of args->missing rather than check whether args->devid
and args->uuid is default value.
Reported-by: syzbot+031687116258450f9853@syzkaller.appspotmail.com Fixes: 562d7b1512f7 ("btrfs: handle device lookup with btrfs_dev_lookup_args") CC: stable@vger.kernel.org # 5.16+ Reviewed-by: Nikolay Borisov <nborisov@suse.com> Signed-off-by: Liu Shixin <liushixin2@huawei.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2. Thread A starts to run and calls rtnl_lock() from within
ath11k_regd_update_work(), then enters wait state because the lock is owned by
thread B.
3. Thread B continues to run and tries to call
cancel_work_sync(&ar->regd_update_work), but thread A is in
ath11k_regd_update_work() waiting for rtnl_lock(). So cancel_work_sync()
forever waits for ath11k_regd_update_work() to finish and we have a deadlock.
Fix this by switching from using regulatory_set_wiphy_regd_sync() to
regulatory_set_wiphy_regd(). Now cfg80211 will schedule another workqueue which
handles the locking on it's own. So the ath11k workqueue can simply exit without
taking any locks, avoiding the deadlock.
After upgrading BIOS to U82 01.02.01 Rev.A, the console is flooded
strange char "^@" which printed out every second and makes login
nearly impossible. Also the below messages were shown both in console
and journal/dmesg every second:
usb 1-3: Device not responding to setup address.
usb 1-3: device not accepting address 4, error -71
usb 1-3: device descriptor read/all, error -71
usb usb1-port3: unable to enumerate USB device
Wifi is soft blocked by checking rfkill. When unblocked manually,
after few seconds it would be soft blocked again. So I was suspecting
something triggered rfkill to soft block wifi. At the end it was
fixed by removing hp_wmi module.
The root cause is the way hp-wmi driver handles command 1B on
post-2009 BIOS. In pre-2009 BIOS, command 1Bh return 0x4 to indicate
that BIOS no longer controls the power for the wireless devices.
mutex_unlock before the exit label because all the error code paths that
jump there didn't take that lock. This fixes unbalanced locking errors
in case of restore errors.
Fixes: 40e8a766a761 ("drm/amdkfd: CRIU checkpoint and restore events") Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com> Reviewed-by: Rajneesh Bhardwaj <rajneesh.bhardwaj@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Checkpoint BOs last. That way we don't need to close dmabuf FDs if
something else fails later. This avoids problematic access to user mode
memory in the error handling code path.
criu_checkpoint_bos has its own error handling and cleanup that does not
depend on access to user memory.
In the private data, keep BOs before the remaining objects. This is
necessary to restore things in the correct order as restoring events
depends on the events-page BO being restored first.
Fixes: be072b06c739 ("drm/amdkfd: CRIU export BOs as prime dmabuf objects") Reported-by: Jann Horn <jannh@google.com> CC: Rajneesh Bhardwaj <Rajneesh.Bhardwaj@amd.com> Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com> Reviewed-and-tested-by: Rajneesh Bhardwaj <rajneesh.bhardwaj@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[Why & How]
New values requested by hardware after fine-tuning.
Update for all memory types.
Reviewed-by: Jun Lei <Jun.Lei@amd.com> Acked-by: Alan Liu <HaoPing.Liu@amd.com> Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org # 6.0.x Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[Why]
The link enablement sequence can end up resetting the encoder while
the PHY symclk isn't yet on.
This means that waiting for symclk on will timeout, along with the reset
bit never asserting high.
This causes unnecessary delay when enabling the link and produces a
warning affecting multiple IGT tests.
[How]
Don't wait for the symclk to be on here because firmware already does.
Don't wait for reset if we know the symclk isn't on.
Split the reset into a helper function that checks the bit and decides
whether or not a delay is sufficient.
Reviewed-by: Roman Li <Roman.Li@amd.com> Acked-by: Alan Liu <HaoPing.Liu@amd.com> Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org # 6.0.x Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need to iterate over the original entries here for the sg_table,
pulling out the struct page for each one, to be remapped. However
currently this incorrectly iterates over the final dma mapped entries,
which is likely just one gigantic sg entry if the iommu is enabled,
leading to us only mapping the first struct page (and any physically
contiguous pages following it), even if there is potentially lots more
data to follow.
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/7306 Fixes: 1286ff739773 ("i915: add dmabuf/prime buffer sharing support.") Signed-off-by: Matthew Auld <matthew.auld@intel.com> Cc: Lionel Landwerlin <lionel.g.landwerlin@intel.com> Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: Michael J. Ruhl <michael.j.ruhl@intel.com> Cc: <stable@vger.kernel.org> # v3.5+ Reviewed-by: Michael J. Ruhl <michael.j.ruhl@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20221028155029.494736-1-matthew.auld@intel.com
(cherry picked from commit 28d52f99bbca7227008cf580c9194c9b3516968e) Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a nilfs2 filesystem is downgraded to read-only due to metadata
corruption on disk and is remounted read/write, or if emergency read-only
remount is performed, detaching a log writer and synchronizing the
filesystem can be done at the same time.
In these cases, use-after-free of the log writer (hereinafter
nilfs->ns_writer) can happen as shown in the scenario below:
While Task1 is sleeping, nilfs->ns_writer is freed by Task2. After Task1
waked up, Task1 accesses nilfs->ns_writer which is already freed. This
scenario diagram is based on the Shigeru Yoshida's post [1].
This patch fixes the issue by not detaching nilfs->ns_writer on remount so
that this UAF race doesn't happen. Along with this change, this patch
also inserts a few necessary read-only checks with superblock instance
where only the ns_writer pointer was used to check if the filesystem is
read-only.
A semaphore deadlock can occur if nilfs_get_block() detects metadata
corruption while locating data blocks and a superblock writeback occurs at
the same time:
task 1 task 2
------ ------
* A file operation *
nilfs_truncate()
nilfs_get_block()
down_read(rwsem A) <--
nilfs_bmap_lookup_contig()
... generic_shutdown_super()
nilfs_put_super()
* Prepare to write superblock *
down_write(rwsem B) <--
nilfs_cleanup_super()
* Detect b-tree corruption * nilfs_set_log_cursor()
nilfs_bmap_convert_error() nilfs_count_free_blocks()
__nilfs_error() down_read(rwsem A) <--
nilfs_set_error()
down_write(rwsem B) <--
*** DEADLOCK ***
Here, nilfs_get_block() readlocks rwsem A (= NILFS_MDT(dat_inode)->mi_sem)
and then calls nilfs_bmap_lookup_contig(), but if it fails due to metadata
corruption, __nilfs_error() is called from nilfs_bmap_convert_error()
inside the lock section.
Since __nilfs_error() calls nilfs_set_error() unless the filesystem is
read-only and nilfs_set_error() attempts to writelock rwsem B (=
nilfs->ns_sem) to write back superblock exclusively, hierarchical lock
acquisition occurs in the order rwsem A -> rwsem B.
Now, if another task starts updating the superblock, it may writelock
rwsem B during the lock sequence above, and can deadlock trying to
readlock rwsem A in nilfs_count_free_blocks().
However, there is actually no need to take rwsem A in
nilfs_count_free_blocks() because it, within the lock section, only reads
a single integer data on a shared struct with
nilfs_sufile_get_ncleansegs(). This has been the case after commit aa474a220180 ("nilfs2: add local variable to cache the number of clean
segments"), that is, even before this bug was introduced.
So, this resolves the deadlock problem by just not taking the semaphore in
nilfs_count_free_blocks().
SAT SCSI/ATA Translation specification requires SCSI SYNCHRONIZE CACHE
(10) and (16) commands both shall be translated to ATA flush command.
Also, ZBC Zoned Block Commands specification mandates SYNCHRONIZE CACHE
(16) command support. However, libata translates only SYNCHRONIZE CACHE
(10). This results in SYNCHRONIZE CACHE (16) command failures on SATA
drives and then libata translation does not conform to ZBC. To avoid the
failure, add support for SYNCHRONIZE CACHE (16).
Signed-off-by: Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com> Cc: stable@vger.kernel.org Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit d4c639990036 ("vmlinux.lds.h: Avoid orphan section with !SMP")
fixed an orphan section warning by adding the '.data..decrypted' section
to the linker script under the PERCPU_DECRYPTED_SECTION define but that
placement introduced a panic with !SMP, as the percpu sections are not
instantiated with that configuration so attempting to access variables
defined with DEFINE_PER_CPU_DECRYPTED() will result in a page fault.
Move the '.data..decrypted' section to the DATA_MAIN define so that the
variables in it are properly instantiated at boot time with
CONFIG_SMP=n.
Accuphase DAC-60 option card supports native DSD up to DSD256,
but doesn't have support for auto-detection. Explicitly enable
DSD support for the correct altsetting.
M-Audio Micro (0762:201a) defines the descriptor as vendor-specific,
while the content seems class-compliant. Just overriding the probe
makes the device working.
Although we tried to fix the regression for the recent changes with
the delayed card registration, it doesn't seem covering the all
cases; e.g. on Roland EDIROL M-100FX, where the generic quirk for
Roland devices is applied, it misses the card registration because the
detection of the last interface (apparently for MIDI) fails.
This patch is an attempt to recover from those failures by calling the
card register also at the error path for the secondary interfaces.
The card register condition is also extended to match with the old
check in the previous patch, too (i.e. the simple check of the
interface number) for catching the probe with errors.
As 'kobject_add' may allocated memory for 'kobject->name' when return error.
And in this function, if call 'kobject_add' failed didn't free kobject.
So call 'kobject_put' to recycling resources.
The Z390 DARK mainboard uses a CA0132 audio controller. The quirk is
needed to enable surround sound and 3.5mm headphone jack handling in
the front audio connector as well as in the rear of the board when in
stereo mode.
Page 97 of the linked manual contains instructions to setup the
controller.
[[ NOTE: this is completely untested by the author, but included solely
because, as noted in commit df57d73276b8 ("mmc: sdhci-pci: Fix
SDHCI_RESET_ALL for CQHCI for Intel GLK-based controllers"), "other
drivers using CQHCI might benefit from a similar change, if they
also have CQHCI reset by SDHCI_RESET_ALL." We've now seen the same
bug on at least MSM, Arasan, and Intel hardware. ]]
SDHCI_RESET_ALL resets will reset the hardware CQE state, but we aren't
tracking that properly in software. When out of sync, we may trigger
various timeouts.
It's not typical to perform resets while CQE is enabled, but this may
occur in some suspend or error recovery scenarios.
Include this fix by way of the new sdhci_and_cqhci_reset() helper.
This patch depends on (and should not compile without) the patch
entitled "mmc: cqhci: Provide helper for resetting both SDHCI and
CQHCI".
Fixes: 3c4019f97978 ("mmc: tegra: HW Command Queue Support for Tegra SDMMC") Signed-off-by: Brian Norris <briannorris@chromium.org> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20221026124150.v4.5.I418c9eaaf754880fcd2698113e8c3ef821a944d7@changeid Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[[ NOTE: this is completely untested by the author, but included solely
because, as noted in commit df57d73276b8 ("mmc: sdhci-pci: Fix
SDHCI_RESET_ALL for CQHCI for Intel GLK-based controllers"), "other
drivers using CQHCI might benefit from a similar change, if they
also have CQHCI reset by SDHCI_RESET_ALL." We've now seen the same
bug on at least MSM, Arasan, and Intel hardware. ]]
SDHCI_RESET_ALL resets will reset the hardware CQE state, but we aren't
tracking that properly in software. When out of sync, we may trigger
various timeouts.
It's not typical to perform resets while CQE is enabled, but this may
occur in some suspend or error recovery scenarios.
Include this fix by way of the new sdhci_and_cqhci_reset() helper.
This patch depends on (and should not compile without) the patch
entitled "mmc: cqhci: Provide helper for resetting both SDHCI and
CQHCI".
Fixes: f545702b74f9 ("mmc: sdhci_am654: Add Support for Command Queuing Engine to J721E") Signed-off-by: Brian Norris <briannorris@chromium.org> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20221026124150.v4.6.I35ca9d6220ba48304438b992a76647ca8e5b126f@changeid Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[[ NOTE: this is completely untested by the author, but included solely
because, as noted in commit df57d73276b8 ("mmc: sdhci-pci: Fix
SDHCI_RESET_ALL for CQHCI for Intel GLK-based controllers"), "other
drivers using CQHCI might benefit from a similar change, if they
also have CQHCI reset by SDHCI_RESET_ALL." We've now seen the same
bug on at least MSM, Arasan, and Intel hardware. ]]
SDHCI_RESET_ALL resets will reset the hardware CQE state, but we aren't
tracking that properly in software. When out of sync, we may trigger
various timeouts.
It's not typical to perform resets while CQE is enabled, but this may
occur in some suspend or error recovery scenarios.
Include this fix by way of the new sdhci_and_cqhci_reset() helper.
I only patch the bcm7216 variant even though others potentially *could*
provide the 'supports-cqe' property (and thus enable CQHCI), because d46ba2d17f90 ("mmc: sdhci-brcmstb: Add support for Command Queuing
(CQE)") and some Broadcom folks confirm that only the 7216 variant
actually supports it.
This patch depends on (and should not compile without) the patch
entitled "mmc: cqhci: Provide helper for resetting both SDHCI and
CQHCI".
Fixes: d46ba2d17f90 ("mmc: sdhci-brcmstb: Add support for Command Queuing (CQE)") Signed-off-by: Brian Norris <briannorris@chromium.org> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20221026124150.v4.3.I6a715feab6d01f760455865e968ecf0d85036018@changeid Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SDHCI_RESET_ALL resets will reset the hardware CQE state, but we aren't
tracking that properly in software. When out of sync, we may trigger
various timeouts.
It's not typical to perform resets while CQE is enabled, but one
particular case I hit commonly enough: mmc_suspend() -> mmc_power_off().
Typically we will eventually deactivate CQE (cqhci_suspend() ->
cqhci_deactivate()), but that's not guaranteed -- in particular, if
we perform a partial (e.g., interrupted) system suspend.
The same bug was already found and fixed for two other drivers, in v5.7
and v5.9:
5cf583f1fb9c ("mmc: sdhci-msm: Deactivate CQE during SDHC reset") df57d73276b8 ("mmc: sdhci-pci: Fix SDHCI_RESET_ALL for CQHCI for Intel
GLK-based controllers")
The latter is especially prescient, saying "other drivers using CQHCI
might benefit from a similar change, if they also have CQHCI reset by
SDHCI_RESET_ALL."
So like these other patches, deactivate CQHCI when resetting the
controller. Do this via the new sdhci_and_cqhci_reset() helper.
This patch depends on (and should not compile without) the patch
entitled "mmc: cqhci: Provide helper for resetting both SDHCI and
CQHCI".
Fixes: 84362d79f436 ("mmc: sdhci-of-arasan: Add CQHCI support for arasan,sdhci-5.1") Cc: <stable@vger.kernel.org> Signed-off-by: Brian Norris <briannorris@chromium.org> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Link: https://lore.kernel.org/r/20221026124150.v4.2.I29f6a2189e84e35ad89c1833793dca9e36c64297@changeid Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / thirdparty / kernel / stable.git / log
