Fix NULL-pointer dereference when clearing halt at open should the device
lack a bulk-out endpoint.
Unable to handle kernel NULL pointer dereference at virtual address 00000030
...
PC is at cyberjack_open+0x40/0x9c [cyberjack]
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Johan Hovold <johan@kernel.org>
[bwh: Backported to 3.2: add this check to the existing
usb_serial_driver::attach implementation] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Andrey Konovalov's fuzz testing of gadgetfs showed that we should
improve the driver's checks for valid configuration descriptors passed
in by the user. In particular, the driver needs to verify that the
wTotalLength value in the descriptor is not too short (smaller
than USB_DT_CONFIG_SIZE). And the check for whether wTotalLength is
too large has to be changed, because the driver assumes there is
always enough room remaining in the buffer to hold a device descriptor
(at least USB_DT_DEVICE_SIZE bytes).
This patch adds the additional check and fixes the existing check. It
may do a little more than strictly necessary, but one extra check
won't hurt.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> CC: Andrey Konovalov <andreyknvl@google.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
[bwh: Backported to 3.2: adjust filename] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The cause of the bug is subtle. The dev_config() routine gets called
twice by the fuzzer. The first time, the user data contains both a
full-speed configuration descriptor and a high-speed config
descriptor, causing dev->hs_config to be set. But it also contains an
invalid device descriptor, so the buffer containing the descriptors is
deallocated and dev_config() returns an error.
The second time dev_config() is called, the user data contains only a
full-speed config descriptor. But dev->hs_config still has the stale
pointer remaining from the first call, causing the routine to think
that there is a valid high-speed config. Later on, when the driver
dereferences the stale pointer to copy that descriptor, we get a
use-after-free access.
The fix is simple: Clear dev->hs_config if the passed-in data does not
contain a high-speed config descriptor.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Reported-by: Andrey Konovalov <andreyknvl@google.com> Tested-by: Andrey Konovalov <andreyknvl@google.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
[bwh: Backported to 3.2: adjust filename] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Indeed, there is a comment saying that the value of len is restricted
to a 16-bit integer, but the code doesn't actually do this.
This patch fixes the warning. It replaces the comment with a
computation that forces the amount of data copied from the user in
ep0_write() to be no larger than the wLength size for the control
transfer, which is a 16-bit quantity.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Reported-by: Andrey Konovalov <andreyknvl@google.com> Tested-by: Andrey Konovalov <andreyknvl@google.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
[bwh: Backported to 3.2 adjust filename] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Andrey Konovalov reported that we were not properly checking the upper
limit before of a device configuration size before calling
memdup_user(), which could cause some problems.
So set the upper limit to PAGE_SIZE * 4, which should be good enough for
all devices.
Reported-by: Andrey Konovalov <andreyknvl@google.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
[bwh: Backported to 3.2: adjust filename] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The stop_activity() routine in dummy-hcd is supposed to unlink all
active requests for every endpoint, among other things. But it
doesn't handle ep0. As a result, fuzz testing can generate a WARNING
like the following:
This patch fixes the problem by iterating over all the endpoints in
the driver's ep array instead of iterating over the gadget's ep_list,
which explicitly leaves out ep0.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Reported-by: Andrey Konovalov <andreyknvl@google.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
[bwh: Backported to 3.2: adjust filename, context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
By convention (according to doc) if function does not provide
get_alt() callback composite framework should assume that it has only
altsetting 0 and should respond with error if host tries to set
other one.
After commit dd4dff8b035f ("USB: composite: Fix bug: should test
set_alt function pointer before use it")
we started checking set_alt() callback instead of get_alt().
This check is useless as we check if set_alt() is set inside
usb_add_function() and fail if it's NULL.
Let's fix this check and move comment about why we check the get
method instead of set a little bit closer to prevent future false
fixes.
Fixes: dd4dff8b035f ("USB: composite: Fix bug: should test set_alt function pointer before use it") Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
This patch removes BUG_ON() macro from mlx4_alloc_icm_coherent()
by checking DMA address alignment in advance and performing proper
folding in case of error.
Fixes: 5b0bf5e25efe ("mlx4_core: Support ICM tables in coherent memory") Reported-by: Ozgur Karatas <okaratas@member.fsf.org> Signed-off-by: Leon Romanovsky <leonro@mellanox.com> Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Single send WQE in RX buffer should be stamped with software
ownership in order to prevent the flow of QP in error in FW
once UPDATE_QP is called.
Fixes: 9f519f68cfff ('mlx4_en: Not using Shared Receive Queues') Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com> Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Commit beb0babfb77e ("korina: disable napi on close and restart")
introduced calls to napi_disable() that were missing before,
unfortunately this leaves a small window during which NAPI has a chance
to run, yet we just freed resources since korina_free_ring() has been
called:
Fix this by disabling NAPI first then freeing resource, and make sure
that we also cancel the restart task before doing the resource freeing.
Fixes: beb0babfb77e ("korina: disable napi on close and restart") Reported-by: Alexandros C. Couloumbis <alex@ozo.com> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Shahar reported a soft lockup in tc_classify(), where we run into an
endless loop when walking the classifier chain due to tp->next == tp
which is a state we should never run into. The issue only seems to
trigger under load in the tc control path.
What happens is that in tc_ctl_tfilter(), thread A allocates a new
tp, initializes it, sets tp_created to 1, and calls into tp->ops->change()
with it. In that classifier callback we had to unlock/lock the rtnl
mutex and returned with -EAGAIN. One reason why we need to drop there
is, for example, that we need to request an action module to be loaded.
This happens via tcf_exts_validate() -> tcf_action_init/_1() meaning
after we loaded and found the requested action, we need to redo the
whole request so we don't race against others. While we had to unlock
rtnl in that time, thread B's request was processed next on that CPU.
Thread B added a new tp instance successfully to the classifier chain.
When thread A returned grabbing the rtnl mutex again, propagating -EAGAIN
and destroying its tp instance which never got linked, we goto replay
and redo A's request.
This time when walking the classifier chain in tc_ctl_tfilter() for
checking for existing tp instances we had a priority match and found
the tp instance that was created and linked by thread B. Now calling
again into tp->ops->change() with that tp was successful and returned
without error.
tp_created was never cleared in the second round, thus kernel thinks
that we need to link it into the classifier chain (once again). tp and
*back point to the same object due to the match we had earlier on. Thus
for thread B's already public tp, we reset tp->next to tp itself and
link it into the chain, which eventually causes the mentioned endless
loop in tc_classify() once a packet hits the data path.
Fix is to clear tp_created at the beginning of each request, also when
we replay it. On the paths that can cause -EAGAIN we already destroy
the original tp instance we had and on replay we really need to start
from scratch. It seems that this issue was first introduced in commit 12186be7d2e1 ("net_cls: fix unconfigured struct tcf_proto keeps chaining
and avoid kernel panic when we use cls_cgroup").
Fixes: 12186be7d2e1 ("net_cls: fix unconfigured struct tcf_proto keeps chaining and avoid kernel panic when we use cls_cgroup") Reported-by: Shahar Klein <shahark@mellanox.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Cc: Cong Wang <xiyou.wangcong@gmail.com> Acked-by: Eric Dumazet <edumazet@google.com> Tested-by: Shahar Klein <shahark@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
[bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
This iscsit_tpg_add_portal_group() function is only called from
lio_target_tiqn_addtpg(). Both functions free the "tpg" pointer on
error so it's a double free bug. The memory is allocated in the caller
so it should be freed in the caller and not here.
Fixes: e48354ce078c ("iscsi-target: Add iSCSI fabric support for target v4.1") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by: David Disseldorp <ddiss@suse.de>
[ bvanassche: Added "Fix" at start of patch title ] Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
A race between scanning and fc_remote_port_delete() may result in a
permanent stop if the device gets blocked before scsi_sysfs_add_sdev()
and unblocked after. The reason is that blocking a device sets both the
SDEV_BLOCKED state and the QUEUE_FLAG_STOPPED. However,
scsi_sysfs_add_sdev() unconditionally sets SDEV_RUNNING which causes the
device to be ignored by scsi_target_unblock() and thus never have its
QUEUE_FLAG_STOPPED cleared leading to a device which is apparently
running but has a stopped queue.
We actually have two places where SDEV_RUNNING is set: once in
scsi_add_lun() which respects the blocked flag and once in
scsi_sysfs_add_sdev() which doesn't. Since the second set is entirely
spurious, simply remove it to fix the problem.
Reported-by: Zengxi Chen <chenzengxi@huawei.com> Signed-off-by: Wei Fang <fangwei1@huawei.com> Reviewed-by: Ewan D. Milne <emilne@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
It is unavoidable that zfcp_scsi_queuecommand() has to finish requests
with DID_IMM_RETRY (like fc_remote_port_chkready()) during the time
window when zfcp detected an unavailable rport but
fc_remote_port_delete(), which is asynchronous via
zfcp_scsi_schedule_rport_block(), has not yet blocked the rport.
However, for the case when the rport becomes available again, we should
prevent unblocking the rport too early. In contrast to other FCP LLDDs,
zfcp has to open each LUN with the FCP channel hardware before it can
send I/O to a LUN. So if a port already has LUNs attached and we
unblock the rport just after port recovery, recoveries of LUNs behind
this port can still be pending which in turn force
zfcp_scsi_queuecommand() to unnecessarily finish requests with
DID_IMM_RETRY.
This also opens a time window with unblocked rport (until the followup
LUN reopen recovery has finished). If a scsi_cmnd timeout occurs during
this time window fc_timed_out() cannot work as desired and such command
would indeed time out and trigger scsi_eh. This prevents a clean and
timely path failover. This should not happen if the path issue can be
recovered on FC transport layer such as path issues involving RSCNs.
Fix this by only calling zfcp_scsi_schedule_rport_register(), to
asynchronously trigger fc_remote_port_add(), after all LUN recoveries as
children of the rport have finished and no new recoveries of equal or
higher order were triggered meanwhile. Finished intentionally includes
any recovery result no matter if successful or failed (still unblock
rport so other successful LUNs work). For simplicity, we check after
each finished LUN recovery if there is another LUN recovery pending on
the same port and then do nothing. We handle the special case of a
successful recovery of a port without LUN children the same way without
changing this case's semantics.
For debugging we introduce 2 new trace records written if the rport
unblock attempt was aborted due to still unfinished or freshly triggered
recovery. The records are only written above the default trace level.
Benjamin noticed the important special case of new recovery that can be
triggered between having given up the erp_lock and before calling
zfcp_erp_action_cleanup() within zfcp_erp_strategy(). We must avoid the
following sequence:
ERP thread rport_work other context
------------------------- -------------- --------------------------------
port is unblocked, rport still blocked,
due to pending/running ERP action,
so ((port->status & ...UNBLOCK) != 0)
and (port->rport == NULL)
unlock ERP
zfcp_erp_action_cleanup()
case ZFCP_ERP_ACTION_REOPEN_LUN:
zfcp_erp_try_rport_unblock()
((status & ...UNBLOCK) != 0) [OLD!]
zfcp_erp_port_reopen()
lock ERP
zfcp_erp_port_block()
port->status clear ...UNBLOCK
unlock ERP
zfcp_scsi_schedule_rport_block()
port->rport_task = RPORT_DEL
queue_work(rport_work)
zfcp_scsi_rport_work()
(port->rport_task != RPORT_ADD)
port->rport_task = RPORT_NONE
zfcp_scsi_rport_block()
if (!port->rport) return
zfcp_scsi_schedule_rport_register()
port->rport_task = RPORT_ADD
queue_work(rport_work)
zfcp_scsi_rport_work()
(port->rport_task == RPORT_ADD)
port->rport_task = RPORT_NONE
zfcp_scsi_rport_register()
(port->rport == NULL)
rport = fc_remote_port_add()
port->rport = rport;
Now the rport was erroneously unblocked while the zfcp_port is blocked.
This is another situation we want to avoid due to scsi_eh
potential. This state would at least remain until the new recovery from
the other context finished successfully, or potentially forever if it
failed. In order to close this race, we take the erp_lock inside
zfcp_erp_try_rport_unblock() when checking the status of zfcp_port or
LUN. With that, the possible corresponding rport state sequences would
be: (unblock[ERP thread],block[other context]) if the ERP thread gets
erp_lock first and still sees ((port->status & ...UNBLOCK) != 0),
(block[other context],NOP[ERP thread]) if the ERP thread gets erp_lock
after the other context has already cleard ...UNBLOCK from port->status.
Since checking fields of struct erp_action is unsafe because they could
have been overwritten (re-used for new recovery) meanwhile, we only
check status of zfcp_port and LUN since these are only changed under
erp_lock elsewhere. Regarding the check of the proper status flags (port
or port_forced are similar to the shown adapter recovery):
Hence, we should check for both UNBLOCK and ERP_INUSE because they are
interleaved. Also we need to explicitly check ERP_FAILED for the link
down case which currently does not clear the UNBLOCK flag in
zfcp_fsf_link_down_info_eval().
Signed-off-by: Steffen Maier <maier@linux.vnet.ibm.com> Fixes: 8830271c4819 ("[SCSI] zfcp: Dont fail SCSI commands when transitioning to blocked fc_rport") Fixes: a2fa0aede07c ("[SCSI] zfcp: Block FC transport rports early on errors") Fixes: 5f852be9e11d ("[SCSI] zfcp: Fix deadlock between zfcp ERP and SCSI") Fixes: 338151e06608 ("[SCSI] zfcp: make use of fc_remote_port_delete when target port is unavailable") Fixes: 3859f6a248cb ("[PATCH] zfcp: add rports to enable scsi_add_device to work again") Reviewed-by: Benjamin Block <bblock@linux.vnet.ibm.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Since quite a while, Linux issues enough SCSI commands per scsi_device
which successfully return with FCP_RESID_UNDER, FSF_FCP_RSP_AVAILABLE,
and SAM_STAT_GOOD. This floods the HBA trace area and we cannot see
other and important HBA trace records long enough.
Therefore, do not trace HBA response errors for pure benign residual
under counts at the default trace level.
This excludes benign residual under count combined with other validity
bits set in FCP_RSP_IU, such as FCP_SNS_LEN_VAL. For all those other
cases, we still do want to see both the HBA record and the corresponding
SCSI record by default.
Signed-off-by: Steffen Maier <maier@linux.vnet.ibm.com> Fixes: a54ca0f62f95 ("[SCSI] zfcp: Redesign of the debug tracing for HBA records.") Reviewed-by: Benjamin Block <bblock@linux.vnet.ibm.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
When SCSI EH invokes zFCP's callbacks for eh_device_reset_handler() and
eh_target_reset_handler(), it expects us to relent the ownership over
the given scsi_cmnd and all other scsi_cmnds within the same scope - LUN
or target - when returning with SUCCESS from the callback ('release'
them). SCSI EH can then reuse those commands.
We did not follow this rule to release commands upon SUCCESS; and if
later a reply arrived for one of those supposed to be released commands,
we would still make use of the scsi_cmnd in our ingress tasklet. This
will at least result in undefined behavior or a kernel panic because of
a wrong kernel pointer dereference.
To fix this, we NULLify all pointers to scsi_cmnds (struct zfcp_fsf_req
*)->data in the matching scope if a TMF was successful. This is done
under the locks (struct zfcp_adapter *)->abort_lock and (struct
zfcp_reqlist *)->lock to prevent the requests from being removed from
the request-hashtable, and the ingress tasklet from making use of the
scsi_cmnd-pointer in zfcp_fsf_fcp_cmnd_handler().
For cases where a reply arrives during SCSI EH, but before we get a
chance to NULLify the pointer - but before we return from the callback
-, we assume that the code is protected from races via the CAS operation
in blk_complete_request() that is called in scsi_done().
The following stacktrace shows an example for a crash resulting from the
previous behavior:
This patch avoids that Coverity complains about not checking the
ib_find_pkey() return value.
Fixes: commit 547af76521b3 ("IB/multicast: Report errors on multicast groups if P_key changes") Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com> Cc: Sean Hefty <sean.hefty@intel.com> Signed-off-by: Doug Ledford <dledford@redhat.com>
[bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The array ib_mad_mgmt_class_table.method_table has MAX_MGMT_CLASS
(80) elements. Hence compare the array index with that value instead
of with IB_MGMT_MAX_METHODS (128). This patch avoids that Coverity
reports the following:
Overrunning array class->method_table of 80 8-byte elements at element index 127 (byte offset 1016) using index convert_mgmt_class(mad_hdr->mgmt_class) (which evaluates to 127).
Fixes: commit b7ab0b19a85f ("IB/mad: Verify mgmt class in received MADs") Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com> Cc: Sean Hefty <sean.hefty@intel.com> Reviewed-by: Hal Rosenstock <hal@mellanox.com> Signed-off-by: Doug Ledford <dledford@redhat.com>
[bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
bdev->bd_contains is not stable before calling __blkdev_get().
When __blkdev_get() is called on a parition with ->bd_openers == 0
it sets
bdev->bd_contains = bdev;
which is not correct for a partition.
After a call to __blkdev_get() succeeds, ->bd_openers will be > 0
and then ->bd_contains is stable.
When FMODE_EXCL is used, blkdev_get() calls
bd_start_claiming() -> bd_prepare_to_claim() -> bd_may_claim()
This call happens before __blkdev_get() is called, so ->bd_contains
is not stable. So bd_may_claim() cannot safely use ->bd_contains.
It currently tries to use it, and this can lead to a BUG_ON().
This happens when a whole device is already open with a bd_holder (in
use by dm in my particular example) and two threads race to open a
partition of that device for the first time, one opening with O_EXCL and
one without.
The thread that doesn't use O_EXCL gets through blkdev_get() to
__blkdev_get(), gains the ->bd_mutex, and sets bdev->bd_contains = bdev;
Immediately thereafter the other thread, using FMODE_EXCL, calls
bd_start_claiming() from blkdev_get(). This should fail because the
whole device has a holder, but because bdev->bd_contains == bdev
bd_may_claim() incorrectly reports success.
This thread continues and blocks on bd_mutex.
The first thread then sets bdev->bd_contains correctly and drops the mutex.
The thread using FMODE_EXCL then continues and when it calls bd_may_claim()
again in:
BUG_ON(!bd_may_claim(bdev, whole, holder));
The BUG_ON fires.
Fix this by removing the dependency on ->bd_contains in
bd_may_claim(). As bd_may_claim() has direct access to the whole
device, it can simply test if the target bdev is the whole device.
Fixes: 6b4517a7913a ("block: implement bd_claiming and claiming block") Signed-off-by: NeilBrown <neilb@suse.com> Signed-off-by: Jens Axboe <axboe@fb.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
fsnotify_unmount_inodes() plays complex tricks to pin next inode in the
sb->s_inodes list when iterating over all inodes. Furthermore the code has a
bug that if the current inode is the last on i_sb_list that does not have e.g.
I_FREEING set, then we leave next_i pointing to inode which may get removed
from the i_sb_list once we drop s_inode_list_lock thus resulting in
use-after-free issues (usually manifesting as infinite looping in
fsnotify_unmount_inodes()).
Fix the problem by keeping current inode pinned somewhat longer. Then we can
make the code much simpler and standard.
Signed-off-by: Jan Kara <jack@suse.cz>
[bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
After sending an authorizer (ceph_x_authorize_a + ceph_x_authorize_b),
the client gets back a ceph_x_authorize_reply, which it is supposed to
verify to ensure the authenticity and protect against replay attacks.
The code for doing this is there (ceph_x_verify_authorizer_reply(),
ceph_auth_verify_authorizer_reply() + plumbing), but it is never
invoked by the the messenger.
AFAICT this goes back to 2009, when ceph authentication protocols
support was added to the kernel client in 4e7a5dcd1bba ("ceph:
negotiate authentication protocol; implement AUTH_NONE protocol").
The second param of ceph_connection_operations::verify_authorizer_reply
is unused all the way down. Pass 0 to facilitate backporting, and kill
it in the next commit.
Signed-off-by: Ilya Dryomov <idryomov@gmail.com> Reviewed-by: Sage Weil <sage@redhat.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The buffer for iucv_message_receive() needs to be below 2 GB. In
__iucv_message_receive(), the buffer address is casted to an u32, which
would result in either memory corruption or an addressing exception when
using addresses >= 2 GB.
Fix this by using GFP_DMA for the buffer allocation.
Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The original code causes a static checker warning because it has a
continue inside a do { } while (0); loop. In that context, a continue
and a break are equivalent. The intent was to go back to the start of
the loop so the continue was a bug.
I've added a retry label at the start and changed the continue to a goto
retry. Then I removed the do { } while (0) loop and pulled the code in
one indent level.
Fixes: 2791c1a43900 ("SPARC/LEON: added support for selecting Timer Core and Timer within core") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Currently it is impossible to edit the value of a config symbol with a
prompt longer than (terminal width - 2) characters. dialog_inputbox()
calculates a negative x-offset for the input window and newwin() fails
as this is invalid. It also doesn't check for this failure, so it
busy-loops calling wgetch(NULL) which immediately returns -1.
The additions in the offset calculations also don't match the intended
size of the window.
Limit the window size and calculate the offset similarly to
show_scroll_win().
Fixes: 692d97c380c6 ("kconfig: new configuration interface (nconfig)") Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
[bwh: Backported to 3.2: replaced code used LINES and COLS] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Don't load an inode with a negative size; this causes integer overflow
problems in the VFS.
[ Added EXT4_ERROR_INODE() to mark file system as corrupted. -TYT]
Fixes: a48380f769df (ext4: rename i_dir_acl to i_size_high) Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Theodore Ts'o <tytso@mit.edu>
[bwh: Backported to 3.2: use EIO instead of EFSCORRUPTED] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
What matters when deciding if we should make a page uptodate is
not how much we _wanted_ to copy, but how much we actually have
copied. As it is, on architectures that do not zero tail on
short copy we can leave uninitialized data in page marked uptodate.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
temp1_max: Suspected overflow: [160000 vs. 0]
temp1_min: Suspected overflow: [160000 vs. 0]
This is seen because the values passed when writing temperature limits
are unbound.
Reviewed-by: Jean Delvare <jdelvare@suse.de> Fixes: 6099469805c2 ("hwmon: Support for Dallas Semiconductor DS620") Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The Logitech QuickCam Communicate Deluxe/S7500 microphone fails with the
following warning.
[ 6.778995] usb 2-1.2.2.2: Warning! Unlikely big volume range (=3072),
cval->res is probably wrong.
[ 6.778996] usb 2-1.2.2.2: [5] FU [Mic Capture Volume] ch = 1, val =
4608/7680/1
Adding it to the list of devices in volume_control_quirks makes it work
properly, fixing related typo.
Signed-off-by: Con Kolivas <kernel@kolivas.org> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Yu Zhao has noticed that __unregister_cpu_notifier only unregisters its
notifiers when HOTPLUG_CPU=y while the registration might succeed even
when HOTPLUG_CPU=n if MODULE is enabled. This means that e.g. zswap
might keep a stale notifier on the list on the manual clean up during
the pool tear down and thus corrupt the list. Resulting in the following
This can be even triggered manually by changing
/sys/module/zswap/parameters/compressor multiple times.
Fix this issue by making unregister APIs symmetric to the register so
there are no surprises.
Fixes: 47e627bc8c9a ("[PATCH] hotplug: Allow modules to use the cpu hotplug notifiers even if !CONFIG_HOTPLUG_CPU") Reported-and-tested-by: Yu Zhao <yuzhao@google.com> Signed-off-by: Michal Hocko <mhocko@suse.com> Cc: linux-mm@kvack.org Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Dan Streetman <ddstreet@ieee.org> Link: http://lkml.kernel.org/r/20161207135438.4310-1-mhocko@kernel.org Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
[bwh: Backported to 3.2:
- The lockless (__-prefixed) variants don't exist
- Keep definition of cpu_notify_nofail() conditional on CONFIG_HOTPLUG_CPU] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
leaf N:
...
item 240 key (282 DIR_LOG_ITEM 0) itemoff 8189 itemsize 8
dir log end 1275809046
leaf N + 1:
item 0 key (282 DIR_LOG_ITEM 3936149215) itemoff 16275 itemsize 8
dir log end 18446744073709551615
...
When we pass the value 1275809046 + 1 as the parameter start_ret to the
function tree-log.c:find_dir_range() (done by replay_dir_deletes()), we
end up with path->slots[0] having the value 239 (points to the last item
of leaf N, item 240). Because the dir log item in that position has an
offset value smaller than *start_ret (1275809046 + 1) we need to move on
to the next leaf, however the logic for that is wrong since it compares
the current slot to the number of items in the leaf, which is smaller
and therefore we don't lookup for the next leaf but instead we set the
slot to point to an item that does not exist, at slot 240, and we later
operate on that slot which has unexpected content or in the worst case
can result in an invalid memory access (accessing beyond the last page
of leaf N's extent buffer).
So fix the logic that checks when we need to lookup at the next leaf
by first incrementing the slot and only after to check if that slot
is beyond the last item of the current leaf.
Signed-off-by: Robbie Ko <robbieko@synology.com> Reviewed-by: Filipe Manana <fdmanana@suse.com> Fixes: e02119d5a7b4 (Btrfs: Add a write ahead tree log to optimize synchronous operations) Signed-off-by: Filipe Manana <fdmanana@suse.com>
[Modified changelog for clarity and correctness] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
GCC 5 generates different code for this bootwrapper null check that
causes the PS3 to hang very early in its bootup. This check is of
limited value, so just get rid of it.
Signed-off-by: Geoff Levand <geoff@infradead.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Function klsi_105_open() calls usb_control_msg() (to "enable read") and
checks its return value. When the return value is unexpected, it only
assigns the error code to the return variable retval, but does not
terminate the exception path. This patch fixes the bug by inserting
"goto err_generic_close;" when the call to usb_control_msg() fails.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Pan Bian <bianpan2016@163.com>
[johan: rebase on prerequisite fix and amend commit message] Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Kill urbs and disable read before returning from open on failure to
retrieve the line state.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Johan Hovold <johan@kernel.org>
[bwh: Backported to 3.2: replaced code was using dbg()] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
In the critical sysfs entry the thermal hwmon was returning wrong
temperature to the user-space. It was reporting the temperature of the
first trip point instead of the temperature of critical trip point.
For example:
/sys/class/hwmon/hwmon0/temp1_crit:50000
/sys/class/thermal/thermal_zone0/trip_point_0_temp:50000
/sys/class/thermal/thermal_zone0/trip_point_0_type:active
/sys/class/thermal/thermal_zone0/trip_point_3_temp:120000
/sys/class/thermal/thermal_zone0/trip_point_3_type:critical
Since commit e68b16abd91d ("thermal: add hwmon sysfs I/F") the driver
have been registering a sysfs entry if get_crit_temp() callback was
provided. However when accessed, it was calling get_trip_temp() instead
of the get_crit_temp().
Fixes: e68b16abd91d ("thermal: add hwmon sysfs I/F") Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Signed-off-by: Zhang Rui <rui.zhang@intel.com>
[bwh: Backported to 3.2: adjust filename] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The function returns -EINVAL even if it builds the stream properly.
The bogus error code sneaked in during the code refactoring, but it
wasn't noticed until now since the returned error code itself is
ignored in anyway. Kill it here, but there is no behavior change by
this patch, obviously.
Commit 2cbbb579bcbe ("regmap: Add the LZO cache support") introduced
'blksize' in regcache_lzo_read() and regcache_lzo_write(), that is
set but not used. Compiling with W=1 gives the following warnings,
fix them.
drivers/base/regmap/regcache-lzo.c: In function ‘regcache_lzo_read’:
drivers/base/regmap/regcache-lzo.c:239:9: warning: variable ‘blksize’ set but not used [-Wunused-but-set-variable]
size_t blksize, tmp_dst_len;
^
drivers/base/regmap/regcache-lzo.c: In function ‘regcache_lzo_write’:
drivers/base/regmap/regcache-lzo.c:278:9: warning: variable ‘blksize’ set but not used [-Wunused-but-set-variable]
size_t blksize, tmp_dst_len;
^
These are harmless warnings and are only being fixed to reduce the
noise with W=1 in the kernel.
Fixes: 2cbbb579bcbe ("regmap: Add the LZO cache support") Cc: Dimitris Papastamos <dp@opensource.wolfsonmicro.com> Cc: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Kirtika Ruchandani <kirtika@chromium.org> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
A recent cleanup had the right idea to remove the initialization
of the error variable, but missed the actual benefit of that,
which is that we get warnings if there is a bug in it. Now
we get a warning about a bug that was introduced by this cleanup:
drivers/media/platform/davinci/vpfe_capture.c: In function 'vpfe_probe':
drivers/media/platform/davinci/vpfe_capture.c:1992:9: error: 'ret' may be used uninitialized in this function [-Werror=maybe-uninitialized]
This adds the missing initialization that the warning is about,
and another one that was preexisting and that we did not get
a warning for. That second bug has existed since the driver
was first added.
Fixes: efb74461f5a6 ("[media] DaVinci-VPFE-Capture: Delete an unnecessary variable initialisation in vpfe_probe()") Fixes: 7da8a6cb3e5b ("V4L/DVB (12248): v4l: vpfe capture bridge driver for DM355 and DM6446")
[mchehab@s-opensource.com: fix a merge conflict] Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
[bwh: Backported to 3.2: adjust filename] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
In crypt_set_key(), if a failure occurs while replacing the old key
(e.g. tfm->setkey() fails) the key must not have DM_CRYPT_KEY_VALID flag
set. Otherwise, the crypto layer would have an invalid key that still
has DM_CRYPT_KEY_VALID flag set.
Signed-off-by: Ondrej Kozina <okozina@redhat.com> Reviewed-by: Mikulas Patocka <mpatocka@redhat.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The commit "ext4: sanity check the block and cluster size at mount
time" should prevent any problems, but in case the superblock is
modified while the file system is mounted, add an extra safety check
to make sure we won't overrun the allocated buffer.
Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Fix a large number of problems with how we handle mount options in the
superblock. For one, if the string in the superblock is long enough
that it is not null terminated, we could run off the end of the string
and try to interpret superblocks fields as characters. It's unlikely
this will cause a security problem, but it could result in an invalid
parse. Also, parse_options is destructive to the string, so in some
cases if there is a comma-separated string, it would be modified in
the superblock. (Fortunately it only happens on file systems with a
1k block size.)
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
[bwh: Backported to 3.2: adjust context, indentation] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
When there is a CRC error in the SPROM read from the device, the code
attempts to handle a fallback SPROM. When this also fails, the driver
returns zero rather than an error code.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
[bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
gcc-7 notices that the condition in mvs_94xx_command_active looks
suspicious:
drivers/scsi/mvsas/mv_94xx.c: In function 'mvs_94xx_command_active':
drivers/scsi/mvsas/mv_94xx.c:671:15: error: '<<' in boolean context, did you mean '<' ? [-Werror=int-in-bool-context]
This was introduced when the mv_printk() statement got added, and leads
to the condition being ignored. This is probably harmless.
Changing '&&' to '&' makes the code look reasonable, as we check the
command bit before setting and printing it.
Fixes: a4632aae8b66 ("[SCSI] mvsas: Add new macros and functions") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The number of 'counters' elements needed in 'struct sg' is
super_block->s_blocksize_bits + 2. Presently we have 16 'counters'
elements in the array. This is insufficient for block sizes >= 32k. In
such cases the memcpy operation performed in ext4_mb_seq_groups_show()
would cause stack memory corruption.
Fixes: c9de560ded61f Signed-off-by: Chandan Rajendra <chandan@linux.vnet.ibm.com> Signed-off-by: Theodore Ts'o <tytso@mit.edu> Reviewed-by: Jan Kara <jack@suse.cz> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
'border' variable is set to a value of 2 times the block size of the
underlying filesystem. With 64k block size, the resulting value won't
fit into a 16-bit variable. Hence this commit changes the data type of
'border' to 'unsigned int'.
Fixes: c9de560ded61f Signed-off-by: Chandan Rajendra <chandan@linux.vnet.ibm.com> Signed-off-by: Theodore Ts'o <tytso@mit.edu> Reviewed-by: Andreas Dilger <adilger@dilger.ca> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Make sure to drop any reference taken by bus_find_device() when creating
devices during init and driver registration.
Fixes: 55347cc9962f ("[POWERPC] ibmebus: Add device creation and bus probing based on of_device") Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Make sure to drop any reference taken by bus_find_device() in the sysfs
callbacks that are used to create and destroy devices based on
device-tree entries.
Fixes: 6bccf755ff53 ("[POWERPC] ibmebus: dynamic addition/removal of adapters, some code cleanup") Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The AEAD givenc descriptor relies on moving the IV through the
output FIFO and then back to the CTX2 for authentication. The
SEQ FIFO STORE could be scheduled before the data can be
read from OFIFO, especially since the SEQ FIFO LOAD needs
to wait for the SEQ FIFO LOAD SKIP to finish first. The
SKIP takes more time when the input is SG than when it's
a contiguous buffer. If the SEQ FIFO LOAD is not scheduled
before the STORE, the DECO will hang waiting for data
to be available in the OFIFO so it can be transferred to C2.
In order to overcome this, first force transfer of IV to C2
by starting the "cryptlen" transfer first and then starting to
store data from OFIFO to the output buffer.
Fixes: 1acebad3d8db8 ("crypto: caam - faster aead implementation") Signed-off-by: Alex Porosanu <alexandru.porosanu@nxp.com> Signed-off-by: Horia Geantă <horia.geanta@nxp.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The UHCI controllers in Intel chipsets rely on a platform-specific non-PME
mechanism for wakeup signalling. They can generate wakeup signals even
though they don't support PME.
We need to let the USB core know this so that it will enable runtime
suspend for UHCI controllers.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
One some systems, the firmware does not allow certain PCI devices to be put
in deep D-states. This can cause problems for wakeup signalling, if the
device does not support PME# in the deepest allowed suspend state. For
example, Pierre reports that on his system, ACPI does not permit his xHCI
host controller to go into D3 during runtime suspend -- but D3 is the only
state in which the controller can generate PME# signals. As a result, the
controller goes into runtime suspend but never wakes up, so it doesn't work
properly. USB devices plugged into the controller are never detected.
If the device relies on PME# for wakeup signals but is not capable of
generating PME# in the target state, the PCI core should accurately report
that it cannot do wakeup from runtime suspend. This patch modifies the
pci_dev_run_wake() routine to add this check.
Reported-by: Pierre de Villemereuil <flyos@mailoo.org> Tested-by: Pierre de Villemereuil <flyos@mailoo.org> Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> CC: Lukas Wunner <lukas@wunner.de> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
There have been several reports over the years of NULL pointer
dereferences in xfs_trans_log_inode during xfs_fsr processes,
when the process is doing an fput and tearing down extents
on the temporary inode, something like:
As it turns out, this is because the i_itemp pointer, along
with the d_ops pointer, has been overwritten with zeros
when we tear down the extents during truncate. When the in-core
inode fork on the temporary inode used by xfs_fsr was originally
set up during the extent swap, we mistakenly looked at di_nextents
to determine whether all extents fit inline, but this misses extents
generated by speculative preallocation; we should be using if_bytes
instead.
This mistake corrupts the in-memory inode, and code in
xfs_iext_remove_inline eventually gets bad inputs, causing
it to memmove and memset incorrect ranges; this became apparent
because the two values in ifp->if_u2.if_inline_ext[1] contained
what should have been in d_ops and i_itemp; they were memmoved due
to incorrect array indexing and then the original locations
were zeroed with memset, again due to an array overrun.
Fix this by properly using i_df.if_bytes to determine the number
of extents, not di_nextents.
Thanks to dchinner for looking at this with me and spotting the
root cause.
Signed-off-by: Eric Sandeen <sandeen@redhat.com> Reviewed-by: Brian Foster <bfoster@redhat.com> Signed-off-by: Dave Chinner <david@fromorbit.com>
[bwh: Backported to 3.2: adjust filename, indentation] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
If CONFIG_ETRAX_AXISFLASHMAP is not configured, the flash rescue image
object file is empty. With recent versions of binutils, this results
in the following build error.
cris-linux-objcopy: error:
the input file 'arch/cris/boot/rescue/rescue.o' has no sections
This is seen, for example, when trying to build cris:allnoconfig
with recently generated toolchains.
Since it does not make sense to build a flash rescue image if there is
no flash, only build it if CONFIG_ETRAX_AXISFLASHMAP is enabled.
Hook up drm_compat_ioctl to support 32-bit userspace on 64-bit kernels.
It turns out that N2600 and N2800 comes with 64-bit enabled. We
previously assumed there where no such systems out there.
usb_endpoint_maxp() returns wMaxPacketSize in its
raw form. Without taking into consideration that it
also contains other bits reserved for isochronous
endpoints.
This patch fixes one occasion where this is a
problem by making sure that we initialize
ep->maxpacket only with lower 10 bits of the value
returned by usb_endpoint_maxp(). Note that seperate
patches will be necessary to audit all call sites of
usb_endpoint_maxp() and make sure that
usb_endpoint_maxp() only returns lower 10 bits of
wMaxPacketSize.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Both register_perl_scripting() and register_python_scripting() allocate
this variable, fix it by checking if it already was.
Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: David Ahern <dsahern@gmail.com> Cc: Frederic Weisbecker <fweisbec@gmail.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Tom Zanussi <tzanussi@gmail.com> Cc: Wang Nan <wangnan0@huawei.com> Fixes: 7e4b21b84c43 ("perf/scripts: Add Python scripting engine") Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Function ite_set_carrier_params() uses variable use_demodulator after
having initialized it to false in some if branches, but this variable is
never set to true otherwise.
This bug has been found using clang -Wsometimes-uninitialized warning
flag.
Fixes: 620a32bba4a2 ("[media] rc: New rc-based ite-cir driver for
several ITE CIRs")
Signed-off-by: Nicolas Iooss <nicolas.iooss_linux@m4x.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
META_COLLECTOR int_vlan_tag() assumes that if the accel tag (vlan_tci)
is zero, then no vlan accel tag is present.
This is incorrect for zero VID vlan accel packets, making the following
match fail:
tc filter add ... basic match 'meta(vlan mask 0xfff eq 0)' ...
Apparently 'int_vlan_tag' was implemented prior VLAN_TAG_PRESENT was
introduced in 05423b2 "vlan: allow null VLAN ID to be used"
(and at time introduced, the 'vlan_tx_tag_get' call in em_meta was not
adapted).
Fix, testing skb_vlan_tag_present instead of testing skb_vlan_tag_get's
value.
Fixes: 05423b2413 ("vlan: allow null VLAN ID to be used") Fixes: 1a31f2042e ("netsched: Allow meta match on vlan tag on receive") Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com> Cc: Eric Dumazet <eric.dumazet@gmail.com> Cc: Stephen Hemminger <stephen@networkplumber.org> Signed-off-by: David S. Miller <davem@davemloft.net>
[bwh: Backported to 3.2: s/skb_vlan_tag/vlan_tx_tag/] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The oversampling ratio is controlled using the oversampling pins,
OS [2:0] with OS2 being the MSB control bit, and OS0 the LSB control
bit.
The gpio connected to the OS2 pin is not being set correctly, only OS0
and OS1 pins are being set. Fix the typo to allow proper control of the
oversampling pins.
Signed-off-by: Eva Rachel Retuya <eraretuya@gmail.com> Fixes: b9618c0 ("staging: IIO: ADC: New driver for AD7606/AD7606-6/AD7606-4") Acked-by: Lars-Peter Clausen <lars@metafoo.de> Signed-off-by: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
In the current DCCP implementation an skb for a DCCP_PKT_REQUEST packet
is forcibly freed via __kfree_skb in dccp_rcv_state_process if
dccp_v6_conn_request successfully returns.
However, if IPV6_RECVPKTINFO is set on a socket, the address of the skb
is saved to ireq->pktopts and the ref count for skb is incremented in
dccp_v6_conn_request, so skb is still in use. Nevertheless, it gets freed
in dccp_rcv_state_process.
Fix by calling consume_skb instead of doing goto discard and therefore
calling __kfree_skb.
Signed-off-by: Andrey Konovalov <andreyknvl@google.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The current implementation failed to detect short transfers when
attempting to read the line state, and also, to make things worse,
logged the content of the uninitialised heap transfer buffer.
Fixes: abf492e7b3ae ("USB: kl5kusb105: fix DMA buffers on stack") Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
When L2 exits to L0 due to "exception or NMI", software exceptions
(#BP and #OF) for which L1 has requested an intercept should be
handled by L1 rather than L0. Previously, only hardware exceptions
were forwarded to L1.
Signed-off-by: Jim Mattson <jmattson@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
[bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Currently kill_fasync() is called outside the stream lock in
snd_pcm_period_elapsed(). This is potentially racy, since the stream
may get released even during the irq handler is running. Although
snd_pcm_release_substream() calls snd_pcm_drop(), this doesn't
guarantee that the irq handler finishes, thus the kill_fasync() call
outside the stream spin lock may be invoked after the substream is
detached, as recently reported by KASAN.
As a quick workaround, move kill_fasync() call inside the stream
lock. The fasync is rarely used interface, so this shouldn't have a
big impact from the performance POV.
Ideally, we should implement some sync mechanism for the proper finish
of stream and irq handler. But this oneliner should suffice for most
cases, so far.
Reported-by: Baozeng Ding <sploving1@gmail.com> Signed-off-by: Takashi Iwai <tiwai@suse.de>
[bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
CAP_NET_ADMIN users should not be allowed to set negative
sk_sndbuf or sk_rcvbuf values, as it can lead to various memory
corruptions, crashes, OOM...
Note that before commit 82981930125a ("net: cleanups in
sock_setsockopt()"), the bug was even more serious, since SO_SNDBUF
and SO_RCVBUF were vulnerable.
This needs to be backported to all known linux kernels.
Again, many thanks to syzkaller team for discovering this gem.
Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: Andrey Konovalov <andreyknvl@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Both damn things interpret userland pointers embedded into the payload;
worse, they are actually traversing those. Leaving aside the bad
API design, this is very much _not_ safe to call with KERNEL_DS.
Bail out early if that happens.
Cc: stable@vger.kernel.org Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Andrey Konovalov reported that KASAN detected that SCTP was using a slab
beyond the boundaries. It was caused because when handling out of the
blue packets in function sctp_sf_ootb() it was checking the chunk len
only after already processing the first chunk, validating only for the
2nd and subsequent ones.
The fix is to just move the check upwards so it's also validated for the
1st chunk.
Reported-by: Andrey Konovalov <andreyknvl@google.com> Tested-by: Andrey Konovalov <andreyknvl@google.com> Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Reviewed-by: Xin Long <lucien.xin@gmail.com> Acked-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
[bwh: Backported to 3.2: moved code is slightly different] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Linus Torvalds [Tue, 8 Nov 2016 10:17:00 +0000 (11:17 +0100)]
Fix potential infoleak in older kernels
Not upstream as it is not needed there.
So a patch something like this might be a safe way to fix the
potential infoleak in older kernels.
THIS IS UNTESTED. It's a very obvious patch, though, so if it compiles
it probably works. It just initializes the output variable with 0 in
the inline asm description, instead of doing it in the exception
handler.
It will generate slightly worse code (a few unnecessary ALU
operations), but it doesn't have any interactions with the exception
handler implementation.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
With syzkaller help, Marco Grassi found a bug in TCP stack,
crashing in tcp_collapse()
Root cause is that sk_filter() can truncate the incoming skb,
but TCP stack was not really expecting this to happen.
It probably was expecting a simple DROP or ACCEPT behavior.
We first need to make sure no part of TCP header could be removed.
Then we need to adjust TCP_SKB_CB(skb)->end_seq
Many thanks to syzkaller team and Marco for giving us a reproducer.
Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: Marco Grassi <marco.gra@gmail.com> Reported-by: Vladis Dronov <vdronov@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
[bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Dccp verifies packet integrity, including length, at initial rcv in
dccp_invalid_packet, later pulls headers in dccp_enqueue_skb.
A call to sk_filter in-between can cause __skb_pull to wrap skb->len.
skb_copy_datagram_msg interprets this as a negative value, so
(correctly) fails with EFAULT. The negative length is reported in
ioctl SIOCINQ or possibly in a DCCP_WARN in dccp_close.
Introduce an sk_receive_skb variant that caps how small a filter
program can trim packets, and call this in dccp with the header
length. Excessively trimmed packets are now processed normally and
queued for reception as 0B payloads.
Fixes: 7c657876b63c ("[DCCP]: Initial implementation") Signed-off-by: Willem de Bruijn <willemb@google.com> Acked-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: David S. Miller <davem@davemloft.net>
[bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Sockets can have a filter program attached that drops or trims
incoming packets based on the filter program return value.
Rose requires data packets to have at least ROSE_MIN_LEN bytes. It
verifies this on arrival in rose_route_frame and unconditionally pulls
the bytes in rose_recvmsg. The filter can trim packets to below this
value in-between, causing pull to fail, leaving the partial header at
the time of skb_copy_datagram_msg.
Place a lower bound on the size to which sk_filter may trim packets
by introducing sk_filter_trim_cap and call this for rose packets.
Signed-off-by: Willem de Bruijn <willemb@google.com> Acked-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: David S. Miller <davem@davemloft.net>
[bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Plugging a Logitech DJ receiver with KASAN activated raises a bunch of
out-of-bound readings.
The fields are allocated up to MAX_USAGE, meaning that potentially, we do
not have enough fields to fit the incoming values.
Add checks and silence KASAN.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
get_task_ioprio() accesses the task->io_context without holding the task
lock and thus can race with exit_io_context(), leading to a
use-after-free. The reproducer below hits this within a few seconds on
my 4-core QEMU VM:
Di Shen reported a race between two concurrent sys_perf_event_open()
calls where both try and move the same pre-existing software group
into a hardware context.
... where, while we wait for a ctx->mutex acquisition, the event->ctx
relation can have changed under us.
That very same commit failed to recognise sys_perf_event_context() as an
external access vector to the events and thereby didn't apply the
established locking rules correctly.
So while one sys_perf_event_open() call is stuck waiting on
mutex_lock_double(), the other (which owns said locks) moves the group
about. So by the time the former sys_perf_event_open() acquires the
locks, the context we've acquired is stale (and possibly dead).
Apply the established locking rules as per perf_event_ctx_lock_nested()
to the mutex_lock_double() for the 'move_group' case. This obviously means
we need to validate state after we acquire the locks.
Reported-by: Di Shen (Keen Lab) Tested-by: John Dias <joaodias@google.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Arnaldo Carvalho de Melo <acme@kernel.org> Cc: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Kees Cook <keescook@chromium.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Min Chong <mchong@google.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Stephane Eranian <eranian@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Vince Weaver <vincent.weaver@maine.edu> Fixes: f63a8daa5812 ("perf: Fix event->ctx locking") Link: http://lkml.kernel.org/r/20170106131444.GZ3174@twins.programming.kicks-ass.net Signed-off-by: Ingo Molnar <mingo@kernel.org>
[bwh: Backported to 3.2:
- Use ACCESS_ONCE() instead of READ_ONCE()
- Test perf_event::group_flags instead of group_caps
- Add the err_locked cleanup block, which we didn't need before
- Adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Since commit c9a4962881929df7f1ef6e63e1b9da304faca4dd ("nfsd:
make client_lock per net") compiling nfs4state.o without
CONFIG_LOCKDEP set, triggers this GCC warning:
fs/nfsd/nfs4state.c: In function ‘free_client’:
fs/nfsd/nfs4state.c:1051:19: warning: unused variable ‘nn’ [-Wunused-variable]
The cause of that warning is that lockdep_assert_held() compiles
away if CONFIG_LOCKDEP is not set. Silence this warning by using
the argument to lockdep_assert_held() as a nop if CONFIG_LOCKDEP
is not set.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Stanislav Kinsbursky <skinsbursky@parallels.com> Cc: J. Bruce Fields <bfields@redhat.com> Link: http://lkml.kernel.org/r/1359060797.1325.33.camel@x61.thuisdomein Signed-off-by: Ingo Molnar <mingo@kernel.org>
[bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
In perf_event_for_each() we call a function on an event, and then
iterate over the siblings of the event.
However we don't call the function on the siblings, we call it
repeatedly on the original event - it seems "obvious" that we should
be calling it with sibling as the argument.
It looks like this broke in commit 75f937f24bd9 ("Fix ctx->mutex
vs counter->mutex inversion").
The only effect of the bug is that the PERF_IOC_FLAG_GROUP parameter
to the ioctls doesn't work.
Line discipline drivers may mistakenly misuse ldisc-related fields
when initializing. For example, a failure to initialize tty->receive_room
in the N_GIGASET_M101 line discipline was recently found and fixed [1].
Now, the N_X25 line discipline has been discovered accessing the previous
line discipline's already-freed private data [2].
Harden the ldisc interface against misuse by initializing revelant
tty fields before instancing the new line discipline.
Commit 79901317ce80 ("n_tty: Don't flush buffer when closing ldisc"),
first merged in kernel release 3.10, caused the following regression
in the Gigaset M101 driver:
Before that commit, when closing the N_TTY line discipline in
preparation to switching to N_GIGASET_M101, receive_room would be
reset to a non-zero value by the call to n_tty_flush_buffer() in
n_tty's close method. With the removal of that call, receive_room
might be left at zero, blocking data reception on the serial line.
The present patch fixes that regression by setting receive_room
to an appropriate value in the ldisc open method.
Fixes: 79901317ce80 ("n_tty: Don't flush buffer when closing ldisc") Signed-off-by: Tilman Schmidt <tilman@imap.cc> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
There's a race on CPU unplug where we free the swevent hash array
while it can still have events on. This will result in a
use-after-free which is BAD.
Simply do not free the hash array on unplug. This leaves the thing
around and no use-after-free takes place.
When the last swevent dies, we do a for_each_possible_cpu() iteration
anyway to clean these up, at which time we'll free it, so no leakage
will occur.
Reported-by: Sasha Levin <sasha.levin@oracle.com> Tested-by: Sasha Levin <sasha.levin@oracle.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Frederic Weisbecker <fweisbec@gmail.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Stephane Eranian <eranian@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Vince Weaver <vincent.weaver@maine.edu> Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
In sg_common_write(), we free the block request and return -ENODEV if
the device is detached in the middle of the SG_IO ioctl().
Unfortunately, sg_finish_rem_req() also tries to free srp->rq, so we
end up freeing rq->cmd in the already free rq object, and then free
the object itself out from under the current user.
This ends up corrupting random memory via the list_head on the rq
object. The most common crash trace I saw is this:
The solution is straightforward: just set srp->rq to NULL in the
failure branch so that sg_finish_rem_req() doesn't attempt to re-free
it.
Additionally, since sg_rq_end_io() will never be called on the object
when this happens, we need to free memory backing ->cmd if it isn't
embedded in the object itself.
KASAN was extremely helpful in finding the root cause of this bug.
Signed-off-by: Calvin Owens <calvinowens@fb.com> Acked-by: Douglas Gilbert <dgilbert@interlog.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
[bwh: Backported to 3.2:
- sg_finish_rem_req() would not free srp->rq->cmd so don't do it here either
- Adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
DMA mapping permissions were being derived from pgprot_kernel directly
without using PAGE_KERNEL. This causes them to be marked with executable
permission, which is not what we want. Fix this.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
[bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Use min_t()/max_t() macros, reformat two comments, use !!test_bit() to
match !!sock_flag()
Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
If we can't allocate the resources in gigaset_initdriver() then we
should return -ENOMEM instead of zero.
Fixes: 2869b23e4b95 ("[PATCH] drivers/isdn/gigaset: new M101 driver (v2)") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
[bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
This patch adds a check to limit the number of can_filters that can be
set via setsockopt on CAN_RAW sockets. Otherwise allocations > MAX_ORDER
are not prevented resulting in a warning.
Reference: https://lkml.org/lkml/2016/12/2/230
Reported-by: Andrey Konovalov <andreyknvl@google.com> Tested-by: Andrey Konovalov <andreyknvl@google.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
[bwh: Backported to 3.2: adjust filename] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
projects / thirdparty / kernel / stable.git / log
