If a faulty CXL memory device returns a broken zero LSA size in its
memory device information (Identify Memory Device (Opcode 4000h), CXL
spec. 3.1, 8.2.9.9.1.1), a divide error occurs in the libnvdimm
driver:
implied that the file system was previously mounted read/write and was
now remounted read-only, when it could have been some other mount
state that had changed by the "mount -o remount" operation. Fix this
by only logging "ro"or "r/w" when it has changed.
MSI remapping bypass (directly configuring MSI entries for devices on the
VMD bus) won't work under Xen, as Xen is not aware of devices in such bus,
and hence cannot configure the entries using the pIRQ interface in the PV
case, and in the PVH case traps won't be setup for MSI entries for such
devices.
Until Xen is aware of devices in the VMD bus prevent the
VMD_FEAT_CAN_BYPASS_MSI_REMAP capability from being used when running as
any kind of Xen guest.
The MSI remapping bypass is an optional feature of VMD bridges, and hence
when running under Xen it will be masked and devices will be forced to
redirect its interrupts from the VMD bridge. That mode of operation must
always be supported by VMD bridges and works when Xen is not aware of
devices behind the VMD bridge.
If the client should see an ENETDOWN when trying to connect to the data
server, it might still be able to talk to the metadata server through
another NIC. If so, report the error.
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com> Reviewed-by: Jeff Layton <jlayton@kernel.org> Tested-by: Jeff Layton <jlayton@kernel.org> Acked-by: Chuck Lever <chuck.lever@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Most systems' PCIe outbound map windows have non-zero physical addresses,
but the possibility of encountering zero increased after following commit
("PCI: dwc: Use parent_bus_offset").
'ep->outbound_addr[n]', representing 'parent_bus_address', might be 0 on
some hardware, which trims high address bits through bus fabric before
sending to the PCIe controller.
Replace the iteration logic with 'for_each_set_bit()' to ensure only
allocated map windows are iterated when determining the ATU index from a
given address.
If opts.uaccess isn't set, the uaccess validation is disabled, but only
partially: it doesn't read the uaccess_safe_builtin list but still tries
to do the validation. Disable it completely to prevent false warnings.
0c1d7a2c2d32 ("lockdep: Remove softirq accounting on PREEMPT_RT.")
the wait context test for mutex usage within "in softirq context" fails
as it references @softirq_context:
| wait context tests |
--------------------------------------------------------------------------
| rcu | raw | spin |mutex |
--------------------------------------------------------------------------
in hardirq context: ok | ok | ok | ok |
in hardirq context (not threaded): ok | ok | ok | ok |
in softirq context: ok | ok | ok |FAILED|
As a fix, add lockdep map for BH disabled section. This fixes the
issue by letting us catch cases when local_bh_disable() gets called
with preemption disabled where local_lock doesn't get acquired.
In the case of "in softirq context" selftest, local_bh_disable() was
being called with preemption disable as it's early in the boot.
[ boqun: Move the lockdep annotations into __local_bh_*() to avoid false
positives because of unpaired local_bh_disable() reported by
Borislav Petkov and Peter Zijlstra, and make bh_lock_map
only exist for PREEMPT_RT. ]
[ mingo: Restored authorship and improved the bh_lock_map definition. ]
Executing dql_reset after setting a non-zero value for limit_min can
lead to an unreasonable situation where dql->limit is less than
dql->limit_min.
For instance, after setting
/sys/class/net/eth*/queues/tx-0/byte_queue_limits/limit_min,
an ifconfig down/up operation might cause the ethernet driver to call
netdev_tx_reset_queue, which in turn invokes dql_reset.
In this case, dql->limit is reset to 0 while dql->limit_min remains
non-zero value, which is unexpected. The limit should always be
greater than or equal to limit_min.
Enable power-down of TMU (Thermal Management Unit) for TMU version 2 during
system suspend to save power. Save approximately 4.3mW on VDD_ANA_1P8 on
i.MX93 platforms.
The autobind setting was supposed to be determined in rpc_create(),
since commit c2866763b402 ("SUNRPC: use sockaddr + size when creating
remote transport endpoints").
Reviewed-by: Jeff Layton <jlayton@kernel.org> Reviewed-by: Benjamin Coddington <bcodding@redhat.com> Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
If a containerised process is killed and causes an ENETUNREACH or
ENETDOWN error to be propagated to the state manager, then mark the
nfs_client as being dead so that we don't loop in functions that are
expecting recovery to succeed.
Reviewed-by: Jeff Layton <jlayton@kernel.org> Reviewed-by: Benjamin Coddington <bcodding@redhat.com> Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Function ip_rfc1001_connect() which establish NetBIOS session for SMB
connections, currently uses smb_send() function for sending NetBIOS Session
Request packet. This function expects that the passed buffer is SMB packet
and for SMB2+ connections it mangles packet header, which breaks prepared
NetBIOS Session Request packet. Result is that this function send garbage
packet for SMB2+ connection, which SMB2+ server cannot parse. That function
is not mangling packets for SMB1 connections, so it somehow works for SMB1.
Fix this problem and instead of smb_send(), use smb_send_kvec() function
which does not mangle prepared packet, this function send them as is. Just
API of this function takes struct msghdr (kvec) instead of packet buffer.
[MS-SMB2] specification allows SMB2 protocol to use NetBIOS as a transport
protocol. NetBIOS can be used over TCP via port 139. So this is a valid
configuration, just not so common. And even recent Windows versions (e.g.
Windows Server 2022) still supports this configuration: SMB over TCP port
139, including for modern SMB2 and SMB3 dialects.
This change fixes SMB2 and SMB3 connections over TCP port 139 which
requires establishing of NetBIOS session. Tested that this change fixes
establishing of SMB2 and SMB3 connections with Windows Server 2022.
Signed-off-by: Pali Rohár <pali@kernel.org> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
I was wondering why there's garbage at the bottom of the screen when
tile blitting is used with an odd mode like 1080, 600 or 200. Sure there's
only space for half a tile but the same area is clean when the buffer
is bitmap.
Then later I found that it's supposed to be cleaned but that's not
implemented. So I took what's in bitblit and adapted it for tileblit.
This implementation was tested for both the horizontal and vertical case,
and now does the same as what's done for bitmap buffers.
If anyone is interested to reproduce the problem then I could bet that'd
be on a S3 or Ark. Just set up a mode with an odd line count and make
sure that the virtual size covers the complete tile at the bottom. E.g.
for 600 lines that's 608 virtual lines for a 16 tall tile. Then the
bottom area should be cleaned.
For the right side it's more difficult as there the drivers won't let an
odd size happen, unless the code is modified. But once it reports back a
few pixel columns short then fbcon won't use the last column. With the
patch that column is now clean.
Btw. the virtual size should be rounded up by the driver for both axes
(not only the horizontal) so that it's dividable by the tile size.
That's a driver bug but correcting it is not in scope for this patch.
The erase colour calculation for fbcon clearing should use get_color instead
of attr_col_ec, like everything else. The latter is similar but is not correct.
For example it's missing the depth dependent remapping and doesn't care about
blanking.
The problem can be reproduced by setting up the background colour to grey
(vt.color=0x70) and having an fbcon console set to 2bpp (4 shades of gray).
Now the background attribute should be 1 (dark gray) on the console.
If the screen is scrolled when pressing enter in a shell prompt at the bottom
line then the new line is cleared using colour 7 instead of 1. That's not
something fillrect likes (at 2bbp it expect 0-3) so the result is interesting.
This patch switches to get_color with vc_video_erase_char to determine the
erase colour from attr_col_ec. That makes the latter function redundant as
no other users were left.
NOMMU kernels currently cannot access memory below the kernel link
address. Remove this restriction by setting PAGE_OFFSET to the actual
start of RAM, as determined from the devicetree. The kernel link address
must be a constant, so keep using CONFIG_PAGE_OFFSET for that purpose.
In case of error, of_parse_phandle_with_args() returns -EINVAL when the
passed index is negative, or -ENOENT when the index is for an empty
phandle. The mailbox core overwrote the error return code with a less
precise -ENODEV. Use the error returned code from
of_parse_phandle_with_args().
The Platform Communication Channel (PCC) mailbox driver currently uses
ioremap() to map channel shared memory regions. However it is preferred
to use acpi_os_ioremap(), which is mapping function specific to EFI/ACPI
defined memory regions. It ensures that the correct memory attributes
are applied when mapping ACPI-provided regions.
While at it, also add checks for handling any errors with the mapping.
Acked-by: Huisong Li <lihuisong@huawei.com> Tested-by: Huisong Li <lihuisong@huawei.com> Tested-by: Adam Young <admiyo@os.amperecomputing.com> Signed-off-by: Sudeep Holla <sudeep.holla@arm.com> Signed-off-by: Jassi Brar <jassisinghbrar@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Intel Over-Clocking Watchdogs are described in ACPI tables by both the
generic PNP0C02 _CID and their ACPI _HID. The presence of the _CID then
causes the PNP scan handler to attach to the watchdog, preventing the
actual watchdog driver from binding. Address this by adding the ACPI
_HIDs to the list of non-PNP devices, so that the PNP scan handler is
bypassed.
Note that these watchdogs can be described by multiple _HIDs for what
seems to be identical hardware. This commit is not a complete list of
all the possible watchdog ACPI _HIDs.
Binary printing functions are using printf() type of format, and compiler
is not happy about them as is:
kernel/trace/trace.c:3292:9: error: function ‘trace_vbprintk’ might be a candidate for ‘gnu_printf’ format attribute [-Werror=suggest-attribute=format]
kernel/trace/trace_seq.c:182:9: error: function ‘trace_seq_bprintf’ might be a candidate for ‘gnu_printf’ format attribute [-Werror=suggest-attribute=format]
Fix the compilation errors by adding __printf() attribute.
While at it, move existing __printf() attributes from the implementations
to the declarations. IT also fixes incorrect attribute parameters that are
used for trace_array_printk().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: Kees Cook <kees@kernel.org> Reviewed-by: Petr Mladek <pmladek@suse.com> Link: https://lore.kernel.org/r/20250321144822.324050-4-andriy.shevchenko@linux.intel.com Signed-off-by: Petr Mladek <pmladek@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The HIP09 processor is vulnerable to the Spectre-BHB (Branch History
Buffer) attack, which can be exploited to leak information through
branch prediction side channels. This commit adds the MIDR of HIP09
to the list for software mitigation.
During mount option processing and negotiation with the server, the
original user-specified rsize/wsize values were being modified directly.
This makes it impossible to recover these values after a connection
reset, leading to potential degraded performance after reconnection.
The other problem is that When negotiating read and write sizes, there are
cases where the negotiated values might calculate to zero, especially
during reconnection when server->max_read or server->max_write might be
reset. In general, these values come from the negotiation response.
According to MS-SMB2 specification, these values should be at least 65536
bytes.
This patch improves IO parameter handling:
1. Adds vol_rsize and vol_wsize fields to store the original user-specified
values separately from the negotiated values
2. Uses got_rsize/got_wsize flags to determine if values were
user-specified rather than checking for non-zero values, which is more
reliable
3. Adds a prevent_zero_iosize() helper function to ensure IO sizes are
never negotiated down to zero, which could happen in edge cases like
when server->max_read/write is zero
The changes make the CIFS client more resilient to unusual server
responses and reconnection scenarios, preventing potential failures
when IO sizes are calculated to be zero.
Signed-off-by: Wang Zhaolong <wangzhaolong1@huawei.com> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
SMB negotiate retry functionality in cifs_negotiate() is currently broken
and does not work when doing socket reconnect. Caller of this function,
which is cifs_negotiate_protocol() requires that tcpStatus after successful
execution of negotiate callback stay in CifsInNegotiate. But if the
CIFSSMBNegotiate() called from cifs_negotiate() fails due to connection
issues then tcpStatus is changed as so repeated CIFSSMBNegotiate() call
does not help.
Fix this problem by moving retrying code from negotiate callback (which is
either cifs_negotiate() or smb2_negotiate()) to cifs_negotiate_protocol()
which is caller of those callbacks. This allows to properly handle and
implement correct transistions between tcpStatus states as function
cifs_negotiate_protocol() already handles it.
With this change, cifs_negotiate_protocol() now handles also -EAGAIN error
set by the RFC1002_NEGATIVE_SESSION_RESPONSE processing after reconnecting
with NetBIOS session.
Signed-off-by: Pali Rohár <pali@kernel.org> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Old SMB1 servers without CAP_NT_SMBS do not support CIFS_open() function
and instead SMBLegacyOpen() needs to be used. This logic is already handled
in cifs_open_file() function, which is server->ops->open callback function.
So for querying and creating MF symlinks use open callback function instead
of CIFS_open() function directly.
This change fixes querying and creating new MF symlinks on Windows 98.
Currently cifs_query_mf_symlink() is not able to detect MF symlink and
cifs_create_mf_symlink() is failing with EIO error.
Signed-off-by: Pali Rohár <pali@kernel.org> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Some operations, like WRITE, does not require FILE_READ_ATTRIBUTES access.
So when FILE_READ_ATTRIBUTES is not explicitly requested for
smb2_open_file() then first try to do SMB2 CREATE with FILE_READ_ATTRIBUTES
access (like it was before) and then fallback to SMB2 CREATE without
FILE_READ_ATTRIBUTES access (less common case).
This change allows to complete WRITE operation to a file when it does not
grant FILE_READ_ATTRIBUTES permission and its parent directory does not
grant READ_DATA permission (parent directory READ_DATA is implicit grant of
child FILE_READ_ATTRIBUTES permission).
Signed-off-by: Pali Rohár <pali@kernel.org> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
An erroneous message is written to the kernel log when either of the
following actions are taken by a user:
1. Assign an adapter or domain to a vfio_ap mediated device via its sysfs
assign_adapter or assign_domain attributes that would result in one or
more AP queues being assigned that are already assigned to a different
mediated device. Sharing of queues between mdevs is not allowed.
2. Reserve an adapter or domain for the host device driver via the AP bus
driver's sysfs apmask or aqmask attribute that would result in providing
host access to an AP queue that is in use by a vfio_ap mediated device.
Reserving a queue for a host driver that is in use by an mdev is not
allowed.
In both cases, the assignment will return an error; however, a message like
the following is written to the kernel log:
Notice the mdev reporting the error is the same as the mdev identified
in the message as the one to which the queue is being assigned.
It is perfectly okay to assign a queue to an mdev to which it is
already assigned; the assignment is simply ignored by the vfio_ap device
driver.
This patch logs more descriptive and accurate messages for both 1 and 2
above to the kernel log:
Example for 1:
vfio_ap_mdev 0fe903a0-a323-44db-9daf-134c68627d61: Userspace may not assign
queue 00.0033 to mdev: already assigned to \ 62177883-f1bb-47f0-914d-32a22e3a8804
Example for 2:
vfio_ap_mdev 62177883-f1bb-47f0-914d-32a22e3a8804: Can not reserve queue
00.0033 for host driver: in use by mdev
The scripts/kconfig/merge_config.sh script requires an existing
$INITFILE (or the $1 argument) as a base file for merging Kconfig
fragments. However, an empty $INITFILE can serve as an initial starting
point, later referenced by the KCONFIG_ALLCONFIG Makefile variable
if -m is not used. This variable can point to any configuration file
containing preset config symbols (the merged output) as stated in
Documentation/kbuild/kconfig.rst. When -m is used $INITFILE will
contain just the merge output requiring the user to run make (i.e.
KCONFIG_ALLCONFIG=<$INITFILE> make <allnoconfig/alldefconfig> or make
olddefconfig).
Instead of failing when `$INITFILE` is missing, create an empty file and
use it as the starting point for merges.
When building the latest samples/bpf on LoongArch Fedora
make M=samples/bpf
There are compilation errors as follows:
In file included from ./linux/samples/bpf/sockex2_kern.c:2:
In file included from ./include/uapi/linux/in.h:25:
In file included from ./include/linux/socket.h:8:
In file included from ./include/linux/uio.h:9:
In file included from ./include/linux/thread_info.h:60:
In file included from ./arch/loongarch/include/asm/thread_info.h:15:
In file included from ./arch/loongarch/include/asm/processor.h:13:
In file included from ./arch/loongarch/include/asm/cpu-info.h:11:
./arch/loongarch/include/asm/loongarch.h:13:10: fatal error: 'larchintrin.h' file not found
^~~~~~~~~~~~~~~
1 error generated.
larchintrin.h is included in /usr/lib64/clang/14.0.6/include,
and the header file location is specified at compile time.
Test on LoongArch Fedora:
https://github.com/fedora-remix-loongarch/releases-info
"sockmap_ktls disconnect_after_delete" test has been failing on BPF CI
after recent merges from netdev:
* https://github.com/kernel-patches/bpf/actions/runs/14458537639
* https://github.com/kernel-patches/bpf/actions/runs/14457178732
It happens because disconnect has been disabled for TLS [1], and it
renders the test case invalid.
Removing all the test code creates a conflict between bpf and
bpf-next, so for now only remove the offending assert [2].
On IMA policy update, if a measure rule exists in the policy,
IMA_MEASURE is set for ima_policy_flags which makes the violation_check
variable always true. Coupled with a no-action on MAY_READ for a
FILE_CHECK call, we're always taking the inode_lock().
This becomes a performance problem for extremely heavy read-only workloads.
Therefore, prevent this only in the case there's no action to be taken.
This small snippet of code ensures that we do something with the array
of RX software buffer descriptor elements after passing the skb to the
stack. In this case, we see if the other half of the page is reusable,
and if so, we "turn around" the buffers, making them directly usable by
enetc_refill_rx_ring() without going to enetc_new_page().
We will need to perform this kind of buffer flipping from a new code
path, i.e. from XDP_PASS. Currently, enetc_build_skb() does it there
buffer by buffer, but in a subsequent change we will stop using
enetc_build_skb() for XDP_PASS.
Assuming the VMM is QEMU. The vq->log_base is from QEMU userpace and can be
reclaimed via gfree(). As a result, this causes invalid memory writes to
QEMU userspace.
The control queue path has the same issue.
Signed-off-by: Dongli Zhang <dongli.zhang@oracle.com> Acked-by: Jason Wang <jasowang@redhat.com> Reviewed-by: Mike Christie <michael.christie@oracle.com>
Message-Id: <20250403063028.16045-2-dongli.zhang@oracle.com> Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When adding folio_memcg function call in the zram module for
Android16-6.12, the following error occurs during compilation:
ERROR: modpost: "cgroup_mutex" [../soc-repo/zram.ko] undefined!
This error is caused by the indirect call to lockdep_is_held(&cgroup_mutex)
within folio_memcg. The export setting for cgroup_mutex is controlled by
the CONFIG_PROVE_RCU macro. If CONFIG_LOCKDEP is enabled while
CONFIG_PROVE_RCU is not, this compilation error will occur.
To resolve this issue, add a parallel macro CONFIG_LOCKDEP control to
ensure cgroup_mutex is properly exported when needed.
When CONFIG_NEED_DMA_MAP_STATE is not defined, dma-mapping clients might
report unused data compilation warnings for dma_unmap_*() calls
arguments. Redefine macros for those calls to let compiler to notice that
it is okay when the provided arguments are not used.
Reported-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Suggested-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Tested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Link: https://lore.kernel.org/r/20250415075659.428549-1-m.szyprowski@samsung.com Signed-off-by: Sasha Levin <sashal@kernel.org>
The struct page->mapping, index fields are deprecated and soon to be only
available as part of a folio.
It is likely the intel_th code which sets page->mapping, index is was
implemented out of concern that some aspect of the page fault logic may
encounter unexpected problems should they not.
However, the appropriate interface for inserting kernel-allocated memory is
vm_insert_page() in a VM_MIXEDMAP. By using the helper function
vmf_insert_mixed() we can do this with minimal churn in the existing fault
handler.
By doing so, we bypass the remainder of the faulting logic. The pages are
still pinned so there is no possibility of anything unexpected being done
with the pages once established.
It would also be reasonable to pre-map everything on fault, however to
minimise churn we retain the fault handler.
We also eliminate all code which clears page->mapping on teardown as this
has now become unnecessary.
The MSU code relies on faulting to function correctly, so is by definition
dependent on CONFIG_MMU. We avoid spurious reports about compilation
failure for unsupported platforms by making this requirement explicit in
Kconfig as part of this change too.
Signed-off-by: Lorenzo Stoakes <lorenzo.stoakes@oracle.com> Acked-by: Alexander Shishkin <alexander.shishkin@linux.intel.com> Link: https://lore.kernel.org/r/20250331125608.60300-1-lorenzo.stoakes@oracle.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
syzbot reports a data-race when accessing the event_triggered, here is the
simplified stack when the issue occurred:
==================================================================
BUG: KCSAN: data-race in virtqueue_disable_cb / virtqueue_enable_cb_delayed
write to 0xffff8881025bc452 of 1 bytes by task 3288 on cpu 0:
virtqueue_enable_cb_delayed+0x42/0x3c0 drivers/virtio/virtio_ring.c:2653
start_xmit+0x230/0x1310 drivers/net/virtio_net.c:3264
__netdev_start_xmit include/linux/netdevice.h:5151 [inline]
netdev_start_xmit include/linux/netdevice.h:5160 [inline]
xmit_one net/core/dev.c:3800 [inline]
read to 0xffff8881025bc452 of 1 bytes by interrupt on cpu 1:
virtqueue_disable_cb_split drivers/virtio/virtio_ring.c:880 [inline]
virtqueue_disable_cb+0x92/0x180 drivers/virtio/virtio_ring.c:2566
skb_xmit_done+0x5f/0x140 drivers/net/virtio_net.c:777
vring_interrupt+0x161/0x190 drivers/virtio/virtio_ring.c:2715
__handle_irq_event_percpu+0x95/0x490 kernel/irq/handle.c:158
handle_irq_event_percpu kernel/irq/handle.c:193 [inline]
value changed: 0x01 -> 0x00
==================================================================
When the data race occurs, the function virtqueue_enable_cb_delayed() sets
event_triggered to false, and virtqueue_disable_cb_split/packed() reads it
as false due to the race condition. Since event_triggered is an unreliable
hint used for optimization, this should only cause the driver temporarily
suggest that the device not send an interrupt notification when the event
index is used.
Fix this KCSAN reported data-race issue by explicitly tagging the access as
data_racy.
Reported-by: syzbot+efe683d57990864b8c8e@syzkaller.appspotmail.com Closes: https://lore.kernel.org/all/67c7761a.050a0220.15b4b9.0018.GAE@google.com/ Signed-off-by: Zhongqiu Han <quic_zhonhan@quicinc.com>
Message-Id: <20250312130412.3516307-1-quic_zhonhan@quicinc.com> Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Acked-by: Jason Wang <jasowang@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Samsung UFS devices require additional time in hibern8 mode before
exiting, beyond the negotiated handshaking phase between the host and
device. Introduce a quirk to increase the PA_HIBERN8TIME parameter by
100 µs, a value derived from experiments, to ensure a proper hibernation
process.
Signed-off-by: Manish Pandey <quic_mapa@quicinc.com> Link: https://lore.kernel.org/r/20250411121630.21330-3-quic_mapa@quicinc.com Reviewed-by: Bean Huo <beanhuo@micron.com> Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
All platforms since Snapdragon 8 Gen1 (SM8450) require using 4-byte
reads to access QFPROM data. While older platforms were more than happy
with 1-byte reads, change the qfprom driver to use 4-byte reads for all
the platforms. Specify stride and word size of 4 bytes. To retain
compatibility with the existing DT and to simplify porting data from
vendor kernels, use fixup_dt_cell_info in order to bump alignment
requirements.
If NVMEM cell uses bit offset or specifies bit truncation, update
raw_len manually (following the cell->bytes update), ensuring that the
NVMEM access is still word-aligned.
Check that the NVMEM cell's raw_len is a aligned to word_size. Otherwise
Otherwise drivers might face incomplete read while accessing the last
part of the NVMEM cell.
The RK3588 has an offset into the OTP area where the readable area begins
and automatically adds this to the start address.
Other variants are very much similar to rk3588, just with a different
offset, so move that value into variant-data.
To match the size in bytes, store this value also in bytes and not in
number of blocks.
The phy-rcar-gen3-usb2 driver exposes four individual PHYs that are
requested and configured by PHY users. The struct phy_ops APIs access the
same set of registers to configure all PHYs. Additionally, PHY settings can
be modified through sysfs or an IRQ handler. While some struct phy_ops APIs
are protected by a driver-wide mutex, others rely on individual
PHY-specific mutexes.
This approach can lead to various issues, including:
1/ the IRQ handler may interrupt PHY settings in progress, racing with
hardware configuration protected by a mutex lock
2/ due to msleep(20) in rcar_gen3_init_otg(), while a configuration thread
suspends to wait for the delay, another thread may try to configure
another PHY (with phy_init() + phy_power_on()); re-running the
phy_init() goes to the exact same configuration code, re-running the
same hardware configuration on the same set of registers (and bits)
which might impact the result of the msleep for the 1st configuring
thread
3/ sysfs can configure the hardware (though role_store()) and it can
still race with the phy_init()/phy_power_on() APIs calling into the
drivers struct phy_ops
To address these issues, add a spinlock to protect hardware register access
and driver private data structures (e.g., calls to
rcar_gen3_is_any_rphy_initialized()). Checking driver-specific data remains
necessary as all PHY instances share common settings. With this change,
the existing mutex protection is removed and the cleanup.h helpers are
used.
While at it, to keep the code simpler, do not skip
regulator_enable()/regulator_disable() APIs in
rcar_gen3_phy_usb2_power_on()/rcar_gen3_phy_usb2_power_off() as the
regulators enable/disable operations are reference counted anyway.
Commit 08b0ad375ca6 ("phy: renesas: rcar-gen3-usb2: move IRQ registration
to init") moved the IRQ request operation from probe to
struct phy_ops::phy_init API to avoid triggering interrupts (which lead to
register accesses) while the PHY clocks (enabled through runtime PM APIs)
are not active. If this happens, it results in a synchronous abort.
One way to reproduce this issue is by enabling CONFIG_DEBUG_SHIRQ, which
calls free_irq() on driver removal.
Move the IRQ request and free operations back to probe, and take the
runtime PM state into account in IRQ handler. This commit is preparatory
for the subsequent fixes in this series.
The Renesas RZ/G3S need to initialize the USB BUS before transferring data
due to hardware limitation. As the register that need to be touched for
this is in the address space of the USB PHY, and the UBS PHY need to be
initialized before any other USB drivers handling data transfer, add
support to initialize the USB BUS.
As the USB PHY is probed before any other USB drivers that enables
clocks and de-assert the reset signals and the BUS initialization is done
in the probe phase, we need to add code to de-assert reset signal and
runtime resume the device (which enables its clocks) before accessing
the registers.
As the reset signals are not required by the USB PHY driver for the other
USB PHY hardware variants, the reset signals and runtime PM was handled
only in the function that initialize the USB BUS.
The PHY initialization was done right after runtime PM enable to have
all in place when the PHYs are registered.
If navi_amd_register_client() fails, the previous i2c_dw_probe() call
should be undone by a corresponding i2c_del_adapter() call, as already done
in the remove function.
Commit 90312351fd1e ("i2c: designware: MASTER mode as separated driver")
introduced ->disable() callback but there is no real use for it. Both
i2c-designware-master.c and i2c-designware-slave.c set it to the same
i2c_dw_disable() and scope is inside the same kernel module.
That said, replace the callback by explicitly calling the i2c_dw_disable().
Reviewed-by: Andi Shyti <andi.shyti@kernel.org> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Stable-dep-of: 1cfe51ef07ca ("i2c: designware: Fix an error handling path in i2c_dw_pci_probe()") Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently initialization flow in i2c_dw_probe_master() skips a few steps
and has code duplication for polling mode implementation.
Simplify this by adding a new ACCESS_POLLING flag that is set for those
two platforms that currently use polling mode and use it to skip
interrupt handler setup.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com> Tested-by: Jiawen Wu <jiawenwu@trustnetic.com> Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Stable-dep-of: 1cfe51ef07ca ("i2c: designware: Fix an error handling path in i2c_dw_pci_probe()") Signed-off-by: Sasha Levin <sashal@kernel.org>
If an input changes state during wake-up and is used as an interrupt
source, the IRQ handler reads the volatile input register to clear the
interrupt mask and deassert the IRQ line. However, the IRQ handler is
triggered before access to the register is granted, causing the read
operation to fail.
As a result, the IRQ handler enters a loop, repeatedly printing the
"failed reading register" message, until `pca953x_resume()` is eventually
called, which restores the driver context and enables access to
registers.
Fix by disabling the IRQ line before entering suspend mode, and
re-enabling it after the driver context is restored in `pca953x_resume()`.
An IRQ can be disabled with disable_irq() and still wake the system as
long as the IRQ has wake enabled, so the wake-up functionality is
preserved.
Set the s3/s0ix and s4 flags in the pm notifier so that we can skip
the resource evictions properly in pm prepare based on whether
we are suspending or hibernating. Drop the eviction as processes
are not frozen at this time, we we can end up getting stuck trying
to evict VRAM while applications continue to submit work which
causes the buffers to get pulled back into VRAM.
v2: Move suspend flags out of pm notifier (Mario)
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/4178 Fixes: 2965e6355dcd ("drm/amd: Add Suspend/Hibernate notification callback support") Cc: Mario Limonciello <mario.limonciello@amd.com> Reviewed-by: Mario Limonciello <mario.limonciello@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 06f2dcc241e7e5c681f81fbc46cacdf4bfd7d6d7) Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We used to take a lock in tegra186_utmi_bias_pad_power_on() but now we
have moved the lock into the caller. Unfortunately, when we moved the
lock this unlock was left behind and it results in a double unlock.
Delete it now.
Fixes: b47158fb4295 ("phy: tegra: xusb: Use a bitmask for UTMI pad power state tracking") Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org> Reviewed-by: Jon Hunter <jonathanh@nvidia.com> Link: https://lore.kernel.org/r/aAjmR6To4EnvRl4G@stanley.mountain Signed-off-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit b15c87263a69 ("hwpoison, memory_hotplug: allow hwpoisoned pages to
be offlined) add page poison checks in do_migrate_range in order to make
offline hwpoisoned page possible by introducing isolate_lru_page and
try_to_unmap for hwpoisoned page. However folio lock must be held before
calling try_to_unmap. Add it to fix this problem.
Warning will be produced if folio is not locked during unmap:
When increasing the array size in memblock_double_array() and the slab
is not yet available, a call to memblock_find_in_range() is used to
reserve/allocate memory. However, the range returned may not have been
accepted, which can result in a crash when booting an SNP guest:
Mitigate this by calling accept_memory() on the memory range returned
before the slab is available.
Prior to v6.12, the accept_memory() interface used a 'start' and 'end'
parameter instead of 'start' and 'size', therefore the accept_memory()
call must be adjusted to specify 'start + size' for 'end' when applying
to kernels prior to v6.12.
Cc: stable@vger.kernel.org # see patch description, needs adjustments for <= 6.11 Fixes: dcdfdd40fa82 ("mm: Add support for unaccepted memory") Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com> Link: https://lore.kernel.org/r/da1ac73bf4ded761e21b4e4bb5178382a580cd73.1746725050.git.thomas.lendacky@amd.com Signed-off-by: Mike Rapoport (Microsoft) <rppt@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
LoongArch's toolchain may change the default code model from normal to
medium. This is unnecessary for kernel, and generates some relocations
which cannot be handled by the module loader. So explicitly specify the
code model to normal in Makefile (for Rust 'normal' is 'small').
When BPF_TRAMP_F_CALL_ORIG is enabled, the address of a bpf_tramp_image
struct on the stack is passed during the size calculation pass and
an address on the heap is passed during code generation. This may
cause a heap buffer overflow if the heap address is tagged because
emit_a64_mov_i64() will emit longer code than it did during the size
calculation pass. The same problem could occur without tag-based
KASAN if one of the 16-bit words of the stack address happened to
be all-ones during the size calculation pass. Fix the problem by
assuming the worst case (4 instructions) when calculating the size
of the bpf_tramp_image address emission.
When BPF_TRAMP_F_CALL_ORIG is set, the trampoline calls
__bpf_tramp_enter() and __bpf_tramp_exit() functions, passing them
the struct bpf_tramp_image *im pointer as an argument in R0.
The trampoline generation code uses emit_addr_mov_i64() to emit
instructions for moving the bpf_tramp_image address into R0, but
emit_addr_mov_i64() assumes the address to be in the vmalloc() space
and uses only 48 bits. Because bpf_tramp_image is allocated using
kzalloc(), its address can use more than 48-bits, in this case the
trampoline will pass an invalid address to __bpf_tramp_enter/exit()
causing a kernel crash.
Fix this by using emit_a64_mov_i64() in place of emit_addr_mov_i64()
as it can work with addresses that are greater than 48-bits.
Fixes: efc9909fdce0 ("bpf, arm64: Add bpf trampoline for arm64") Signed-off-by: Puranjay Mohan <puranjay@kernel.org> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Closes: https://lore.kernel.org/all/SJ0PR15MB461564D3F7E7A763498CA6A8CBDB2@SJ0PR15MB4615.namprd15.prod.outlook.com/ Link: https://lore.kernel.org/bpf/20240711151838.43469-1-puranjay@kernel.org
[Minor context change fixed.] Signed-off-by: Bin Lan <bin.lan.cn@windriver.com> Signed-off-by: He Zhe <zhe.he@windriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
nr_failed was missing the large folio splits from migrate_pages_batch()
and can cause a mismatch between migrate_pages() return value and the
number of not migrated pages, i.e., when the return value of
migrate_pages() is 0, there are still pages left in the from page list.
It will happen when a non-PMD THP large folio fails to migrate due to
-ENOMEM and is split successfully but not all the split pages are not
migrated, migrate_pages_batch() would return non-zero, but
astats.nr_thp_split = 0. nr_failed would be 0 and returned to the caller
of migrate_pages(), but the not migrated pages are left in the from page
list without being added back to LRU lists.
Fix it by adding a new nr_split counter for large folio splits and adding
it to nr_failed in migrate_page_sync() after migrate_pages_batch() is
done.
Link: https://lkml.kernel.org/r/20231017163129.2025214-1-zi.yan@sent.com Fixes: 2ef7dbb26990 ("migrate_pages: try migrate in batch asynchronously firstly") Signed-off-by: Zi Yan <ziy@nvidia.com> Acked-by: Huang Ying <ying.huang@intel.com> Reviewed-by: Baolin Wang <baolin.wang@linux.alibaba.com> Cc: David Hildenbrand <david@redhat.com> Cc: Matthew Wilcox <willy@infradead.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Huacai Chen <chenhuacai@loongson.cn> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When running mm selftest to verify mm patches, 'compaction_test' case
failed on an x86 server with 1TB memory. And the root cause is that it
has too much free memory than what the test supports.
The test case tries to allocate 100000 huge pages, which is about 200 GB
for that x86 server, and when it succeeds, it expects it's large than 1/3
of 80% of the free memory in system. This logic only works for platform
with 750 GB ( 200 / (1/3) / 80% ) or less free memory, and may raise false
alarm for others.
Fix it by changing the fixed page number to self-adjustable number
according to the real number of free memory.
Link: https://lkml.kernel.org/r/20250423103645.2758-1-feng.tang@linux.alibaba.com Fixes: bd67d5c15cc1 ("Test compaction of mlocked memory") Signed-off-by: Feng Tang <feng.tang@linux.alibaba.com> Acked-by: Dev Jain <dev.jain@arm.com> Reviewed-by: Baolin Wang <baolin.wang@linux.alibaba.com> Tested-by: Baolin Wang <baolin.wang@inux.alibaba.com> Cc: Shuah Khan <shuah@kernel.org> Cc: Sri Jayaramappa <sjayaram@akamai.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch introduces the ucsi_con_mutex_lock / ucsi_con_mutex_unlock
functions to the UCSI driver. ucsi_con_mutex_lock ensures the connector
mutex is only locked if a connection is established and the partner pointer
is valid. This resolves a deadlock scenario where
ucsi_displayport_remove_partner holds con->mutex waiting for
dp_altmode_work to complete while dp_altmode_work attempts to acquire it.
Cc: stable <stable@kernel.org> Fixes: af8622f6a585 ("usb: typec: ucsi: Support for DisplayPort alt mode") Signed-off-by: Andrei Kuchynski <akuchynski@chromium.org> Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Link: https://lore.kernel.org/r/20250424084429.3220757-2-akuchynski@chromium.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fixes a kernel panic seen during release FW in a stress test
scenario where WLAN and BT FW download occurs simultaneously, and due to
a HW bug, chip sends out only 1 bootloader signatures.
When driver receives the bootloader signature, it enters FW download
mode, but since no consequtive bootloader signatures seen, FW file is
not requested.
After 60 seconds, when FW download times out, release_firmware causes a
kernel panic.
Fixes: e3c4891098c8 ("Bluetooth: btnxpuart: Handle FW Download Abort scenario") Fixes: 689ca16e5232 ("Bluetooth: NXP: Add protocol support for NXP Bluetooth chipsets") Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Bin Lan <bin.lan.cn@windriver.com> Signed-off-by: He Zhe <zhe.he@windriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The page allocator tracks the number of zones that have unaccepted memory
using static_branch_enc/dec() and uses that static branch in hot paths to
determine if it needs to deal with unaccepted memory.
Borislav and Thomas pointed out that the tracking is racy: operations on
static_branch are not serialized against adding/removing unaccepted pages
to/from the zone.
WARNING: CPU: 0 PID: 10 at kernel/jump_label.c:276 __static_key_slow_dec_cpuslocked+0x8e/0xa0
The comment around the WARN() explains the problem:
/*
* Warn about the '-1' case though; since that means a
* decrement is concurrent with a first (0->1) increment. IOW
* people are trying to disable something that wasn't yet fully
* enabled. This suggests an ordering problem on the user side.
*/
The effect of this static_branch optimization is only visible on
microbenchmark.
Instead of adding more complexity around it, remove it altogether.
Link: https://lkml.kernel.org/r/20250506133207.1009676-1-kirill.shutemov@linux.intel.com Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Fixes: dcdfdd40fa82 ("mm: Add support for unaccepted memory") Link: https://lore.kernel.org/all/20250506092445.GBaBnVXXyvnazly6iF@fat_crate.local Reported-by: Borislav Petkov <bp@alien8.de> Tested-by: Borislav Petkov (AMD) <bp@alien8.de> Reported-by: Thomas Gleixner <tglx@linutronix.de> Cc: Vlastimil Babka <vbabka@suse.cz> Cc: Suren Baghdasaryan <surenb@google.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Brendan Jackman <jackmanb@google.com> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: <stable@vger.kernel.org> [6.5+] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pawan Gupta [Mon, 19 May 2025 20:43:42 +0000 (13:43 -0700)]
x86/its: Fix build error for its_static_thunk()
Due to a likely merge resolution error of backport commit 772934d9062a
("x86/its: FineIBT-paranoid vs ITS"), the function its_static_thunk() was
placed in the wrong ifdef block, causing a build error when
CONFIG_MITIGATION_ITS and CONFIG_FINEIBT are both disabled:
The idxd_cleanup() helper cleans up perfmon, interrupts, internals and
so on. Refactor remove call with the idxd_cleanup() helper to avoid code
duplication. Note, this also fixes the missing put_device() for idxd
groups, enginces and wqs.
Fixes: bfe1d56091c1 ("dmaengine: idxd: Init and probe for Intel data accelerators") Cc: stable@vger.kernel.org Suggested-by: Vinicius Costa Gomes <vinicius.gomes@intel.com> Signed-off-by: Shuai Xue <xueshuai@linux.alibaba.com> Reviewed-by: Fenghua Yu <fenghuay@nvidia.com> Reviewed-by: Dave Jiang <dave.jiang@intel.com> Link: https://lore.kernel.org/r/20250404120217.48772-10-xueshuai@linux.alibaba.com Signed-off-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Memory allocated for idxd is not freed if an error occurs during
idxd_pci_probe(). To fix it, free the allocated memory in the reverse
order of allocation before exiting the function in case of an error.
Fixes: bfe1d56091c1 ("dmaengine: idxd: Init and probe for Intel data accelerators") Cc: stable@vger.kernel.org Signed-off-by: Shuai Xue <xueshuai@linux.alibaba.com> Reviewed-by: Dave Jiang <dave.jiang@intel.com> Reviewed-by: Fenghua Yu <fenghuay@nvidia.com> Link: https://lore.kernel.org/r/20250404120217.48772-8-xueshuai@linux.alibaba.com Signed-off-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Memory allocated for idxd is not freed if an error occurs during
idxd_alloc(). To fix it, free the allocated memory in the reverse order
of allocation before exiting the function in case of an error.
The remove call stack is missing idxd cleanup to free bitmap, ida and
the idxd_device. Call idxd_free() helper routines to make sure we exit
gracefully.
Fixes: bfe1d56091c1 ("dmaengine: idxd: Init and probe for Intel data accelerators") Cc: stable@vger.kernel.org Suggested-by: Vinicius Costa Gomes <vinicius.gomes@intel.com> Signed-off-by: Shuai Xue <xueshuai@linux.alibaba.com> Reviewed-by: Fenghua Yu <fenghuay@nvidia.com> Reviewed-by: Dave Jiang <dave.jiang@intel.com> Link: https://lore.kernel.org/r/20250404120217.48772-9-xueshuai@linux.alibaba.com Signed-off-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The idxd_cleanup_internals() function only decreases the reference count
of groups, engines, and wqs but is missing the step to release memory
resources.
To fix this, use the cleanup helper to properly release the memory
resources.
Fixes: ddf742d4f3f1 ("dmaengine: idxd: Add missing cleanup for early error out in probe call") Cc: stable@vger.kernel.org Signed-off-by: Shuai Xue <xueshuai@linux.alibaba.com> Reviewed-by: Fenghua Yu <fenghuay@nvidia.com> Reviewed-by: Dave Jiang <dave.jiang@intel.com> Link: https://lore.kernel.org/r/20250404120217.48772-6-xueshuai@linux.alibaba.com Signed-off-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Memory allocated for groups is not freed if an error occurs during
idxd_setup_groups(). To fix it, free the allocated memory in the reverse
order of allocation before exiting the function in case of an error.
Memory allocated for engines is not freed if an error occurs during
idxd_setup_engines(). To fix it, free the allocated memory in the
reverse order of allocation before exiting the function in case of an
error.
Memory allocated for wqs is not freed if an error occurs during
idxd_setup_wqs(). To fix it, free the allocated memory in the reverse
order of allocation before exiting the function in case of an error.
Currently, a local dma_cap_mask_t variable is used to store device
cap_mask within udma_of_xlate(). However, the DMA_PRIVATE flag in
the device cap_mask can get cleared when the last channel is released.
This can happen right after storing the cap_mask locally in
udma_of_xlate(), and subsequent dma_request_channel() can fail due to
mismatch in the cap_mask. Fix this by removing the local dma_cap_mask_t
variable and directly using the one from the dma_device structure.
After a recent change [1] in clang's randstruct implementation to
randomize structures that only contain function pointers, there is an
error because qede_ll_ops get randomized but does not use a designated
initializer for the first member:
drivers/net/ethernet/qlogic/qede/qede_main.c:206:2: error: a randomized struct can only be initialized with a designated initializer
206 | {
| ^
Explicitly initialize the common member using a designated initializer
to fix the build.
A warning on driver removal started occurring after commit 9dd05df8403b
("net: warn if NAPI instance wasn't shut down"). Disable tx napi before
deleting it in mt76_dma_cleanup().
Tested with mt7921e but the same pattern can be actually applied to other
mt76 drivers calling mt76_dma_cleanup() during removal. Tx napi is enabled
in their *_dma_init() functions and only toggled off and on again inside
their suspend/resume/reset paths. So it should be okay to disable tx
napi in such a generic way.
Found by Linux Verification Center (linuxtesting.org).
Fixes: 2ac515a5d74f ("mt76: mt76x02: use napi polling for tx cleanup") Cc: stable@vger.kernel.org Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru> Tested-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com> Link: https://patch.msgid.link/20250506115540.19045-1-pchelkin@ispras.ru Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A delay unit of 0 is a valid entry, thus it is not valid to check for
unused delays. Instead, check the value field; if that is zero, the
given delay is unset.
Fixes: 4426e6b4ecf6 ("spi: tegra114: Don't fail set_cs_timing when delays are zero") Cc: stable@vger.kernel.org Signed-off-by: Aaron Kling <webgeek1234@gmail.com> Reviewed-by: Jon Hunter <jonathanh@nvidia.com> Link: https://patch.msgid.link/20250506-spi-tegra114-fixup-v1-1-136dc2f732f3@gmail.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The response buffer for the CREATE request handled by smb311_posix_mkdir()
is leaked on the error path (goto err_free_rsp_buf) because the structure
pointer *rsp passed to free_rsp_buf() is not assigned until *after* the
error condition is checked.
As *rsp is initialised to NULL, free_rsp_buf() becomes a no-op and the leak
is instead reported by __kmem_cache_shutdown() upon subsequent rmmod of
cifs.ko if (and only if) the error path has been hit.
Pass rsp_iov.iov_base to free_rsp_buf() instead, similar to the code in
other functions in smb2pdu.c for which *rsp is assigned late.
Cc: stable@vger.kernel.org Signed-off-by: Jethro Donaldson <devel@jro.nz> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The REPORT ZONES buffer size is currently limited by the HBA's maximum
segment count to ensure the buffer can be mapped. However, the block
layer further limits the number of iovec entries to 1024 when allocating
a bio.
To avoid allocation of buffers too large to be mapped, further restrict
the maximum buffer size to BIO_MAX_INLINE_VECS.
Replace the UIO_MAXIOV symbolic name with the more contextually
appropriate BIO_MAX_INLINE_VECS.
Fixes: b091ac616846 ("sd_zbc: Fix report zones buffer allocation") Cc: stable@vger.kernel.org Signed-off-by: Steve Siwinski <ssiwinski@atto.com> Link: https://lore.kernel.org/r/20250508200122.243129-1-ssiwinski@atto.com Reviewed-by: Damien Le Moal <dlemoal@kernel.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
phy-rcar-gen3-usb2 driver exports 4 PHYs. The timing registers are common
to all PHYs. There is no need to set them every time a PHY is initialized.
Set timing register only when the 1st PHY is initialized.
It has been observed on the Renesas RZ/G3S SoC that unbinding and binding
the PHY driver leads to role autodetection failures. This issue occurs when
PHY 3 is the first initialized PHY. PHY 3 does not have an interrupt
associated with the USB2_INT_ENABLE register (as
rcar_gen3_int_enable[3] = 0). As a result, rcar_gen3_init_otg() is called
to initialize OTG without enabling PHY interrupts.
To resolve this, add rcar_gen3_is_any_otg_rphy_initialized() and call it in
role_store(), role_show(), and rcar_gen3_init_otg(). At the same time,
rcar_gen3_init_otg() is only called when initialization for a PHY with
interrupt bits is in progress. As a result, the
struct rcar_gen3_phy::otg_initialized is no longer needed.
projects / thirdparty / kernel / stable.git / log
