If the callee gpmi_alloc_dma_buffer() failed to alloc memory for
this->raw_buffer, gpmi_free_dma_buffer() will be called to free
this->auxiliary_virt. But this->auxiliary_virt is still a non-NULL
and valid ptr.
Then gpmi_alloc_dma_buffer() returns err and gpmi_free_dma_buffer()
is called again to free this->auxiliary_virt in err_out. This causes
a double free.
As gpmi_free_dma_buffer() has already called in gpmi_alloc_dma_buffer's
error path, so it should return err directly instead of releasing the dma
buffer again.
The function adf_isr_resource_alloc() is not unwinding correctly in case
of error.
This patch fixes the error paths and propagate the errors to the caller.
Fixes: 7afa232e76ce ("crypto: qat - Intel(R) QAT DH895xcc accelerator") Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com> Reviewed-by: Marco Chiappero <marco.chiappero@intel.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
Put child node before return to fix potential reference count leak.
Generally, the reference count of child is incremented and decremented
automatically in the macro for_each_available_child_of_node() and should
be decremented manually if the loop is broken in loop body.
MEMLOCK, MEMUNLOCK and OTPLOCK modify protection bits. Thus require
write permission. Depending on the hardware MEMLOCK might even be
write-once, e.g. for SPI-NOR flashes with their WP# tied to GND. OTPLOCK
is always write-once.
MEMSETBADBLOCK modifies the bad block table.
Fixes: f7e6b19bc764 ("mtd: properly check all write ioctls for permissions") Signed-off-by: Michael Walle <michael@walle.cc> Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Acked-by: Rafał Miłecki <rafal@milecki.pl> Acked-by: Richard Weinberger <richard@nod.at> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20210303155735.25887-1-michael@walle.cc Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently it leaves unhandled interrupts unmasked, but those are never
acked. In the case of a "device idle" interrupt, this leads to an
effectively frozen system until plugging it in.
When the EP0 IN request was not completed but less than a packet sent,
it would complete the request successfully. That doesn't make sense
and can't really happen as fotg210_start_dma always sends
min(length, maxpkt) bytes.
For a 134 Byte packet, it sends the first two 64 Byte packets just fine,
but then notice that less than a packet is remaining and call fotg210_done
without actually sending the rest.
For a 75 Byte request, it would send the first 64 separately, then detect
that the remaining 11 Byte fit into a single DMA, but due to this bug set
the length to the original 75 Bytes. This leads to a DMA failure (which is
ignored...) and the request completes without the remaining bytes having
been sent.
ADF_STATUS_PF_RUNNING is (only) used and checked by adf_vf2pf_shutdown()
before calling adf_iov_putmsg()->mutex_lock(vf2pf_lock), however the
vf2pf_lock is initialized in adf_dev_init(), which can fail and when it
fail, the vf2pf_lock is either not initialized or destroyed, a subsequent
use of vf2pf_lock will cause issue.
To fix this issue, only set this flag if adf_dev_init() returns 0.
adf_vf_isr_resource_alloc() is not unwinding correctly when error
happens and it want to release uninitialized resources.
To fix this, only release initialized resources.
DMA mapping might fail, we have to check it with dma_mapping_error().
Otherwise DMA-API is not happy:
DMA-API: pch_udc 0000:02:02.4: device driver failed to check map error[device address=0x00000000027ee678] [size=64 bytes] [mapped as single]
Fixes: abab0c67c061 ("usb: pch_udc: Fixed issue which does not work with g_serial") Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Link: https://lore.kernel.org/r/20210323153626.54908-3-andriy.shevchenko@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Either way ~0 will be in the correct byte order, hence
replace cpu_to_le32() by lower_32_bits(). Moreover,
it makes sparse happy, otherwise it complains:
.../pch_udc.c:1813:27: warning: incorrect type in assignment (different base types)
.../pch_udc.c:1813:27: expected unsigned int [usertype] dataptr
.../pch_udc.c:1813:27: got restricted __le32 [usertype]
Incorrect characters are observed on console during boot. This issue occurs
when init/main.c is modifying termios settings to open /dev/console on the
rootfs.
This patch adds a waiting loop in set_termios to wait for TX shift register
empty (and TX FIFO if any) before stopping serial port.
The Maxim PMIC datasheets describe the interrupt line as active low
with a requirement of acknowledge from the CPU. Without specifying the
interrupt type in Devicetree, kernel might apply some fixed
configuration, not necessarily working for this hardware.
Additionally, the interrupt line is shared so using level sensitive
interrupt is here especially important to avoid races.
The Maxim PMIC datasheets describe the interrupt line as active low
with a requirement of acknowledge from the CPU. Without specifying the
interrupt type in Devicetree, kernel might apply some fixed
configuration, not necessarily working for this hardware.
Additionally, the interrupt line is shared so using level sensitive
interrupt is here especially important to avoid races.
Fixes: 47580e8d94c2 ("ARM: dts: Specify MAX77686 pmic interrupt for exynos5250-smdk5250") Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Link: https://lore.kernel.org/r/20201210212534.216197-8-krzk@kernel.org Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently the array gpmc_cs is indexed by cs before it cs is range checked
and the pointer read from this out-of-index read is dereferenced. Fix this
by performing the range check on cs before the read and the following
pointer dereference.
Addresses-Coverity: ("Negative array index read") Fixes: 9ed7a776eb50 ("ARM: OMAP2+: Fix support for multiple devices on a GPMC chip select") Signed-off-by: Colin Ian King <colin.king@canonical.com> Reviewed-by: Tony Lindgren <tony@atomide.com> Link: https://lore.kernel.org/r/20210223193821.17232-1-colin.king@canonical.com Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The commit d3cb25a12138 ("usb: gadget: udc: fix spin_lock in pch_udc")
obviously was not thought through and had made the situation even worse
than it was before. Two changes after almost reverted it. but a few
leftovers have been left as it. With this revert d3cb25a12138 completely.
While at it, narrow down the scope of unlocked section to prevent
potential race when prot_stall is assigned.
The quirk entry for Uniwill ECS M31EI is with the PCI SSID device 0,
which means matching with all. That is, it's essentially equivalent
with SND_PCI_QUIRK_VENDOR(0x1584), which also matches with the
previous entry for Haier W18 applying the very same quirk.
Let's unify them with the single vendor-quirk entry.
Just re-order the alc269_fixup_tbl[] entries for Lenovo devices for
avoiding the oversight of the duplicated or unapplied item in future.
No functional changes.
Also Cc-to-stable for the further patch applications.
Just re-order the alc269_fixup_tbl[] entries for Sony devices for
avoiding the oversight of the duplicated or unapplied item in future.
No functional changes.
Also Cc-to-stable for the further patch applications.
Just re-order the alc882_fixup_tbl[] entries for Sony devices for
avoiding the oversight of the duplicated or unapplied item in future.
No functional changes.
Also Cc-to-stable for the further patch applications.
Just re-order the alc882_fixup_tbl[] entries for Acer devices for
avoiding the oversight of the duplicated or unapplied item in future.
No functional changes.
Also Cc-to-stable for the further patch applications.
Currently the ioctl command RADEON_INFO_SI_BACKEND_ENABLED_MASK can
copy back uninitialised data in value_tmp that pointer *value points
to. This can occur when rdev->family is less than CHIP_BONAIRE and
less than CHIP_TAHITI. Fix this by adding in a missing -EINVAL
so that no invalid value is copied back to userspace.
Addresses-Coverity: ("Uninitialized scalar variable) Cc: stable@vger.kernel.org # 3.13+ Fixes: 439a1cfffe2c ("drm/radeon: expose render backend mask to the userspace") Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If we overflow the maximum number of BSS entries and free the
new entry, drop it from any hidden_list that it may have been
added to in the code above or in cfg80211_combine_bsses().
commit d3374825ce57 ("md: make devices disappear when they are no longer
needed.") introduced protection between mddev creating & removing. The
md_open shouldn't create mddev when all_mddevs list doesn't contain
mddev. With currently code logic, there will be very easy to trigger
soft lockup in non-preempt env.
This patch changes md_open returning from -ERESTARTSYS to -EBUSY, which
will break the infinitely retry when md_open enter racing area.
This patch is partly fix soft lockup issue, full fix needs mddev_find
is split into two functions: mddev_find & mddev_find_or_alloc. And
md_open should call new mddev_find (it only does searching job).
For more detail, please refer with Christoph's "split mddev_find" patch
in later commits.
*** env ***
kvm-qemu VM 2C1G with 2 iscsi luns
kernel should be non-preempt
I use mdcluster env to trigger soft lockup, but it isn't mdcluster
speical bug. To stop md array in mdcluster env will do more jobs than
non-cluster array, which will leave enough time/gap to allow kernel to
run md_open.
"mdadm -A" (or other array assemble commands) will start a daemon "mdadm
--monitor" by default. When "mdadm -Ss" is running, the stop action will
wakeup "mdadm --monitor". The "--monitor" daemon will immediately get
info from /proc/mdstat. This time mddev in kernel still exist, so
/proc/mdstat still show md device, which makes "mdadm --monitor" to open
/dev/md0.
The previously "mdadm -Ss" is removing action, the "mdadm --monitor"
open action will trigger md_open which is creating action. Racing is
happening.
```
<thread 1>: "mdadm -Ss"
md_release
mddev_put deletes mddev from all_mddevs
queue_work for mddev_delayed_delete
at this time, "/dev/md0" is still available for opening
<thread 2>: "mdadm --monitor ..."
md_open
+ mddev_find can't find mddev of /dev/md0, and create a new mddev and
| return.
+ trigger "if (mddev->gendisk != bdev->bd_disk)" and return
-ERESTARTSYS.
```
In non-preempt kernel, <thread 2> is occupying on current CPU. and
mddev_delayed_delete which was created in <thread 1> also can't be
schedule.
In preempt kernel, it can also trigger above racing. But kernel doesn't
allow one thread running on a CPU all the time. after <thread 2> running
some time, the later "mdadm -A" (refer above script line 13) will call
md_alloc to alloc a new gendisk for mddev. it will break md_open
statement "if (mddev->gendisk != bdev->bd_disk)" and return 0 to caller,
the soft lockup is broken.
Cc: stable@vger.kernel.org Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Zhao Heming <heming.zhao@suse.com> Signed-off-by: Song Liu <song@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes: dbb64f8635f5d ("md-cluster: Fix adding of new disk with new reload code") Fixes: 659b254fa7392 ("md-cluster: remove a disk asynchronously from cluster environment") Cc: stable@vger.kernel.org Reviewed-by: Gang He <ghe@suse.com> Signed-off-by: Heming Zhao <heming.zhao@suse.com> Signed-off-by: Song Liu <song@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It was reported that a fix to the ring buffer recursion detection would
cause a hung machine when performing suspend / resume testing. The
following backtrace was extracted from debugging that case:
Since the fix to the recursion detection would allow a single recursion to
happen while tracing, this lead to the trace_clock_global() taking a spin
lock and then trying to take it again:
ring_buffer_lock_reserve() {
trace_clock_global() {
arch_spin_lock() {
queued_spin_lock_slowpath() {
/* lock taken */
(something else gets traced by function graph tracer)
ring_buffer_lock_reserve() {
trace_clock_global() {
arch_spin_lock() {
queued_spin_lock_slowpath() {
/* DEAD LOCK! */
Tracing should *never* block, as it can lead to strange lockups like the
above.
Restructure the trace_clock_global() code to instead of simply taking a
lock to update the recorded "prev_time" simply use it, as two events
happening on two different CPUs that calls this at the same time, really
doesn't matter which one goes first. Use a trylock to grab the lock for
updating the prev_time, and if it fails, simply try again the next time.
If it failed to be taken, that means something else is already updating
it.
Link: https://lkml.kernel.org/r/20210430121758.650b6e8a@gandalf.local.home Cc: stable@vger.kernel.org Tested-by: Konstantin Kharlamov <hi-angel@yandex.ru> Tested-by: Todd Brandt <todd.e.brandt@linux.intel.com> Fixes: b02414c8f045 ("ring-buffer: Fix recursion protection transitions between interrupt context") # started showing the problem Fixes: 14131f2f98ac3 ("tracing: implement trace_clock_*() APIs") # where the bug happened
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=212761 Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The default max PID is set by PID_MAX_DEFAULT, and the tracing
infrastructure uses this number to map PIDs to the comm names of the
tasks, such output of the trace can show names from the recorded PIDs in
the ring buffer. This mapping is also exported to user space via the
"saved_cmdlines" file in the tracefs directory.
But currently the mapping expects the PIDs to be less than
PID_MAX_DEFAULT, which is the default maximum and not the real maximum.
Recently, systemd will increases the maximum value of a PID on the system,
and when tasks are traced that have a PID higher than PID_MAX_DEFAULT, its
comm is not recorded. This leads to the entire trace to have "<...>" as
the comm name, which is pretty useless.
Instead, keep the array mapping the size of PID_MAX_DEFAULT, but instead
of just mapping the index to the comm, map a mask of the PID
(PID_MAX_DEFAULT - 1) to the comm, and find the full PID from the
map_cmdline_to_pid array (that already exists).
This bug goes back to the beginning of ftrace, but hasn't been an issue
until user space started increasing the maximum value of PIDs.
Strcpy is inherently not safe, and strlcpy() should be used instead.
__trace_find_cmdline() uses strcpy() because the comms saved must have a
terminating nul character, but it doesn't hurt to add the extra protection
of using strlcpy() instead of strcpy().
Link: http://lkml.kernel.org/r/1493806274-13936-1-git-send-email-amit.pundir@linaro.org Signed-off-by: Amey Telawane <ameyt@codeaurora.org>
[AmitP: Cherry-picked this commit from CodeAurora kernel/msm-3.10
https://source.codeaurora.org/quic/la/kernel/msm-3.10/commit/?id=2161ae9a70b12cf18ac8e5952a20161ffbccb477] Signed-off-by: Amit Pundir <amit.pundir@linaro.org>
[ Updated change log and removed the "- 1" from len parameter ] Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently we stop recording comm for non-idle tasks when switching from/to idle
task since we treat that as a record failure. Fix that by treat recording of
comm for idle task as a success.
Link: http://lkml.kernel.org/r/20170706230023.17942-1-joelaf@google.com Cc: kernel-team@android.com Cc: Ingo Molnar <mingo@redhat.com> Reported-by: Michael Sartain <mikesart@gmail.com> Signed-off-by: Joel Fernandes <joelaf@google.com> Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
KMSAN complains that the vmci_use_ppn64() == false path in
vmci_dbell_register_notification_bitmap() left upper 32bits of
bitmap_set_msg.bitmap_ppn64 member uninitialized.
Local variable ----bitmap_set_msg@vmci_dbell_register_notification_bitmap created at:
vmci_dbell_register_notification_bitmap+0x50/0x1e0
vmci_dbell_register_notification_bitmap+0x50/0x1e0
Bytes 28-31 of 32 are uninitialized
Memory access of size 32 starts at ffff88810098f570
=====================================================
Before this commit lis3lv02d_get_pwron_wait() had a WARN_ONCE() to catch
a potential divide by 0. WARN macros should only be used to catch internal
kernel bugs and that is not the case here. We have been receiving a lot of
bug reports about kernel backtraces caused by this WARN.
The div value being checked comes from the lis3->odrs[] array. Which
is sized to be a power-of-2 matching the number of bits in lis3->odr_mask.
The only lis3 model where this array is not entirely filled with non zero
values. IOW the only model where we can hit the div == 0 check is the
3dc ("8 bits 3DC sensor") model:
Note the 0 value at index 0, according to the datasheet an odr index of 0
means "Power-down mode". HP typically uses a lis3 accelerometer for HDD
fall protection. What I believe is happening here is that on newer
HP devices, which only contain a SDD, the BIOS is leaving the lis3 device
powered-down since it is not used for HDD fall protection.
Note that the lis3_3dc_rates array initializer only specifies 10 values,
which matches the datasheet. So it also contains 6 zero values at the end.
Replace the WARN with a normal check, which treats an odr index of 0
as power-down and uses a normal dev_err() to report the error in case
odr index point past the initialized part of the array.
Recent versions of the PCI Express specification have deprecated support
for I/O transactions and actually some PCIe host bridges, such as Power
Systems Host Bridge 4 (PHB4), do not implement them.
For those systems the PCI BARs that request a mapping in the I/O space
have the length recorded in the corresponding PCI resource set to zero,
which makes it unassigned:
# lspci -s 0031:02:04.0 -v
0031:02:04.0 FDDI network controller: Digital Equipment Corporation PCI-to-PDQ Interface Chip [PFI] FDDI (DEFPA) (rev 02)
Subsystem: Digital Equipment Corporation FDDIcontroller/PCI (DEFPA)
Flags: bus master, medium devsel, latency 136, IRQ 57, NUMA node 8
Memory at 620c080020000 (32-bit, non-prefetchable) [size=128]
I/O ports at <unassigned> [disabled]
Memory at 620c080030000 (32-bit, non-prefetchable) [size=64K]
Capabilities: [50] Power Management version 2
Kernel driver in use: defxx
Kernel modules: defxx
#
Regardless the driver goes ahead and requests it (here observed with a
Raptor Talos II POWER9 system), resulting in an odd /proc/ioport entry:
Furthermore, the system gets confused as the driver actually continues
and pokes at those locations, causing a flood of messages being output
to the system console by the underlying system firmware, like:
defxx: v1.11 2014/07/01 Lawrence V. Stefani and others
defxx 0031:02:04.0: enabling device (0140 -> 0142)
LPC[000]: Got SYNC no-response error. Error address reg: 0xd0010000
IPMI: dropping non severe PEL event
LPC[000]: Got SYNC no-response error. Error address reg: 0xd0010014
IPMI: dropping non severe PEL event
LPC[000]: Got SYNC no-response error. Error address reg: 0xd0010014
IPMI: dropping non severe PEL event
and so on and so on (possibly intermixed actually, as there's no locking
between the kernel and the firmware in console port access with this
particular system, but cleaned up above for clarity), and once some 10k
of such pairs of the latter two messages have been produced an interace
eventually shows up in a useless state:
This was not expected to happen as resource handling was added to the
driver a while ago, because it was not known at that time that a PCI
system would be possible that cannot assign port I/O resources, and
oddly enough `request_region' does not fail, which would have caught it.
Correct the problem then by checking for the length of zero for the CSR
resource and bail out gracefully refusing to register an interface if
that turns out to be the case, producing messages like:
defxx: v1.11 2014/07/01 Lawrence V. Stefani and others
0031:02:04.0: Cannot use I/O, no address set, aborting
0031:02:04.0: Recompile driver with "CONFIG_DEFXX_MMIO=y"
Keep the original check for the EISA MMIO resource as implemented,
because in that case the length is hardwired to 0x400 as a consequence
of how the compare/mask address decoding works in the ESIC chip and it
is only the base address that is set to zero if MMIO has been disabled
for the adapter in EISA configuration, which in turn could be a valid
bus address in a legacy-free system implementing PCI, especially for
port I/O.
Where the EISA MMIO resource has been disabled for the adapter in EISA
configuration this arrangement keeps producing messages like:
eisa 00:05: EISA: slot 5: DEC3002 detected
defxx: v1.11 2014/07/01 Lawrence V. Stefani and others
00:05: Cannot use MMIO, no address set, aborting
00:05: Recompile driver with "CONFIG_DEFXX_MMIO=n"
00:05: Or run ECU and set adapter's MMIO location
with the last two lines now swapped for easier handling in the driver.
There is no need to check for and catch the case of a port I/O resource
not having been assigned for EISA as the adapter uses the slot-specific
I/O space, which gets assigned by how EISA has been specified and maps
directly to the particular slot an option card has been placed in. And
the EISA variant of the adapter has additional registers that are only
accessible via the port I/O space anyway.
While at it factor out the error message calls into helpers and fix an
argument order bug with the `pr_err' call now in `dfx_register_res_err'.
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk> Fixes: 4d0438e56a8f ("defxx: Clean up DEFEA resource management") Cc: stable@vger.kernel.org # v3.19+ Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commits 8a4cd82d ("nfc: fix refcount leak in llcp_sock_connect()")
and c33b1cc62 ("nfc: fix refcount leak in llcp_sock_bind()")
fixed a refcount leak bug in bind/connect but introduced a
use-after-free if the same local is assigned to 2 different sockets.
This can be triggered by the following simple program:
int sock1 = socket( AF_NFC, SOCK_STREAM, NFC_SOCKPROTO_LLCP );
int sock2 = socket( AF_NFC, SOCK_STREAM, NFC_SOCKPROTO_LLCP );
memset( &addr, 0, sizeof(struct sockaddr_nfc_llcp) );
addr.sa_family = AF_NFC;
addr.nfc_protocol = NFC_PROTO_NFC_DEP;
bind( sock1, (struct sockaddr*) &addr, sizeof(struct sockaddr_nfc_llcp) )
bind( sock2, (struct sockaddr*) &addr, sizeof(struct sockaddr_nfc_llcp) )
close(sock1);
close(sock2);
Fix this by assigning NULL to llcp_sock->local after calling
nfc_llcp_local_put.
This addresses CVE-2021-23134.
Reported-by: Or Cohen <orcohen@paloaltonetworks.com> Reported-by: Nadav Markus <nmarkus@paloaltonetworks.com> Fixes: c33b1cc62 ("nfc: fix refcount leak in llcp_sock_bind()") Signed-off-by: Or Cohen <orcohen@paloaltonetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a possible race condition vulnerability between issuing a HCI
command and removing the cont. Specifically, functions hci_req_sync()
and hci_dev_do_close() can race each other like below:
thread-A in hci_req_sync() | thread-B in hci_dev_do_close()
| hci_req_sync_lock(hdev);
test_bit(HCI_UP, &hdev->flags); |
... | test_and_clear_bit(HCI_UP, &hdev->flags)
hci_req_sync_lock(hdev); |
|
In this commit we alter the sequence in function hci_req_sync(). Hence,
the thread-A cannot issue th.
Signed-off-by: Lin Ma <linma@zju.edu.cn> Cc: Marcel Holtmann <marcel@holtmann.org> Fixes: 7c6a329e4447 ("[Bluetooth] Fix regression from using default link policy") Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When HSR interface is sending a frame, it finds a node with
the destination ethernet address from the list.
If there is no node, it calls WARN_ONCE().
But, using WARN_ONCE() for this situation is a little bit overdoing.
So, in this patch, the netdev_err() is used instead.
Signed-off-by: Taehee Yoo <ap420073@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Cc: George Kennedy <george.kennedy@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
hci_chan can be created in 2 places: hci_loglink_complete_evt() if
it is an AMP hci_chan, or l2cap_conn_add() otherwise. In theory,
Only AMP hci_chan should be removed by a call to
hci_disconn_loglink_complete_evt(). However, the controller might mess
up, call that function, and destroy an hci_chan which is not initiated
by hci_loglink_complete_evt().
This patch adds a verification that the destroyed hci_chan must have
been init'd by hci_loglink_complete_evt().
Memory state around the buggy address: ffff8881d7af9080: fc fc fc fc fc fc fc fc fb fb fb fb fb fb fb fb ffff8881d7af9100: fb fb fb fb fb fb fb fb fc fc fc fc fc fc fc fc
>ffff8881d7af9180: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
^ ffff8881d7af9200: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc ffff8881d7af9280: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
When loading a device-mapper table for a request-based mapped device,
and the allocation/initialization of the blk_mq_tag_set for the device
fails, a following device remove will cause a double free.
When allocation/initialization of the blk_mq_tag_set fails in
dm_mq_init_request_queue(), it is uninitialized/freed, but the pointer
is not reset to NULL; so when dev_remove() later gets into
dm_mq_cleanup_mapped_device() it sees the pointer and tries to
uninitialize and free it again.
Fix this by setting the pointer to NULL in dm_mq_init_request_queue()
error-handling. Also set it to NULL in dm_mq_cleanup_mapped_device().
Cc: <stable@vger.kernel.org> # 4.6+ Fixes: 1c357a1e86a4 ("dm: allocate blk_mq_tag_set rather than embed in mapped_device") Signed-off-by: Benjamin Block <bblock@linux.ibm.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This division bug meant the search for free metadata space could skip
the final allocation bitmap's worth of entries. Fix affects DM thinp,
cache and era targets.
Cc: stable@vger.kernel.org Signed-off-by: Joe Thornber <ejt@redhat.com> Tested-by: Ming-Hung Tsai <mtsai@redhat.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes bug with the handling of more than one language in
the string table in f_fs.c.
str_count was not reset for subsequent language codes.
str_count-- "rolls under" and processes u32 max strings on
the processing of the second language entry.
The existing bug can be reproduced by adding a second language table
to the structure "strings" in tools/usb/ffs-test.c.
Upon driver unbind usb_free_all_descriptors() function frees all
speed descriptor pointers without setting them to NULL. In case
gadget speed changes (i.e from super speed plus to super speed)
after driver unbind only upto super speed descriptor pointers get
populated. Super speed plus desc still holds the stale (already
freed) pointer. Fix this issue by setting all descriptor pointers
to NULL after freeing them in usb_free_all_descriptors().
Fixes: f5c61225cf29 ("usb: gadget: Update function for SuperSpeedPlus")
cc: stable@vger.kernel.org Reviewed-by: Peter Chen <peter.chen@kernel.org> Signed-off-by: Hemant Kumar <hemantk@codeaurora.org> Signed-off-by: Wesley Cheng <wcheng@codeaurora.org> Link: https://lore.kernel.org/r/1619034452-17334-1-git-send-email-wcheng@codeaurora.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix a general protection fault reported by syzbot due to a race between
gadget_setup() and gadget_unbind() in raw_gadget.
The gadget core is supposed to guarantee that there won't be any more
callbacks to the gadget driver once the driver's unbind routine is
called. That guarantee is enforced in usb_gadget_remove_driver as
follows:
usb_gadget_disconnect(udc->gadget);
if (udc->gadget->irq)
synchronize_irq(udc->gadget->irq);
udc->driver->unbind(udc->gadget);
usb_gadget_udc_stop(udc);
usb_gadget_disconnect turns off the pullup resistor, telling the host
that the gadget is no longer connected and preventing the transmission
of any more USB packets. Any packets that have already been received
are sure to processed by the UDC driver's interrupt handler by the time
synchronize_irq returns.
But this doesn't work with dummy_hcd, because dummy_hcd doesn't use
interrupts; it uses a timer instead. It does have code to emulate the
effect of synchronize_irq, but that code doesn't get invoked at the
right time -- it currently runs in usb_gadget_udc_stop, after the unbind
callback instead of before. Indeed, there's no way for
usb_gadget_remove_driver to invoke this code before the unbind callback.
To fix this, move the synchronize_irq() emulation code to dummy_pullup
so that it runs before unbind. Also, add a comment explaining why it is
necessary to have it there.
dvb_media_device_free() is leaking memory. Free `dvbdev->adapter->conn`
before setting it to NULL, as documented in include/media/media-device.h:
"The media_entity instance itself must be freed explicitly by the driver
if required."
We should set the error code when ext4_commit_super check argument failed.
Found in code review. Fixes: c4be0c1dc4cdc ("filesystem freeze: add error handling of write_super_lockfs/unlockfs"). Cc: stable@kernel.org Signed-off-by: Fengnan Chang <changfengnan@vivo.com> Reviewed-by: Andreas Dilger <adilger@dilger.ca> Link: https://lore.kernel.org/r/20210402101631.561-1-changfengnan@vivo.com Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit <50122847007> ("ext4: fix check to prevent initializing reserved
inodes") check the block group zero and prevent initializing reserved
inodes. But in some special cases, the reserved inode may not all belong
to the group zero, it may exist into the second group if we format
filesystem below.
So, it will end up triggering a false positive report of a corrupted
file system. This patch fix it by avoid check reserved inodes if no free
inode blocks will be zeroed.
Cc: stable@kernel.org Fixes: 50122847007 ("ext4: fix check to prevent initializing reserved inodes") Signed-off-by: Zhang Yi <yi.zhang@huawei.com> Suggested-by: Jan Kara <jack@suse.cz> Link: https://lore.kernel.org/r/20210331121516.2243099-1-yi.zhang@huawei.com Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The reason is that the parsing in the write function only processes
commands if it finished parsing (there is white space written after the
command). That's to handle:
cases, where the command is broken over multiple writes.
The problem is if the file descriptor is closed, then the write call is
not processed, and the command needs to be processed in the release code.
The release code can handle matching of functions, but does not handle
commands.
Cc: stable@vger.kernel.org Fixes: eda1e32855656 ("tracing: handle broken names in ftrace filter") Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The FUTEX_WAIT operand has historically a relative timeout which means that
the clock id is irrelevant as relative timeouts on CLOCK_REALTIME are not
subject to wall clock changes and therefore are mapped by the kernel to
CLOCK_MONOTONIC for simplicity.
If a caller would set FUTEX_CLOCK_REALTIME for FUTEX_WAIT the timeout is
still treated relative vs. CLOCK_MONOTONIC and then the wait arms that
timeout based on CLOCK_REALTIME which is broken and obviously has never
been used or even tested.
Reject any attempt to use FUTEX_CLOCK_REALTIME with FUTEX_WAIT again.
The desired functionality can be achieved with FUTEX_WAIT_BITSET and a
FUTEX_BITSET_MATCH_ANY argument.
Fixes: 337f13046ff0 ("futex: Allow FUTEX_CLOCK_REALTIME with FUTEX_WAIT op") Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20210422194704.834797921@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
KASAN reports a BUG when download file in jffs2 filesystem.It is
because when dstlen == 1, cpage_out will write array out of bounds.
Actually, data will not be compressed in jffs2_zlib_compress() if
data's length less than 4.
[ 393.799778] BUG: KASAN: slab-out-of-bounds in jffs2_rtime_compress+0x214/0x2f0 at addr ffff800062e3b281
[ 393.809166] Write of size 1 by task tftp/2918
[ 393.813526] CPU: 3 PID: 2918 Comm: tftp Tainted: G B 4.9.115-rt93-EMBSYS-CGEL-6.1.R6-dirty #1
[ 393.823173] Hardware name: LS1043A RDB Board (DT)
[ 393.827870] Call trace:
[ 393.830322] [<ffff20000808c700>] dump_backtrace+0x0/0x2f0
[ 393.835721] [<ffff20000808ca04>] show_stack+0x14/0x20
[ 393.840774] [<ffff2000086ef700>] dump_stack+0x90/0xb0
[ 393.845829] [<ffff20000827b19c>] kasan_object_err+0x24/0x80
[ 393.851402] [<ffff20000827b404>] kasan_report_error+0x1b4/0x4d8
[ 393.857323] [<ffff20000827bae8>] kasan_report+0x38/0x40
[ 393.862548] [<ffff200008279d44>] __asan_store1+0x4c/0x58
[ 393.867859] [<ffff2000084ce2ec>] jffs2_rtime_compress+0x214/0x2f0
[ 393.873955] [<ffff2000084bb3b0>] jffs2_selected_compress+0x178/0x2a0
[ 393.880308] [<ffff2000084bb530>] jffs2_compress+0x58/0x478
[ 393.885796] [<ffff2000084c5b34>] jffs2_write_inode_range+0x13c/0x450
[ 393.892150] [<ffff2000084be0b8>] jffs2_write_end+0x2a8/0x4a0
[ 393.897811] [<ffff2000081f3008>] generic_perform_write+0x1c0/0x280
[ 393.903990] [<ffff2000081f5074>] __generic_file_write_iter+0x1c4/0x228
[ 393.910517] [<ffff2000081f5210>] generic_file_write_iter+0x138/0x288
[ 393.916870] [<ffff20000829ec1c>] __vfs_write+0x1b4/0x238
[ 393.922181] [<ffff20000829ff00>] vfs_write+0xd0/0x238
[ 393.927232] [<ffff2000082a1ba8>] SyS_write+0xa0/0x110
[ 393.932283] [<ffff20000808429c>] __sys_trace_return+0x0/0x4
[ 393.937851] Object at ffff800062e3b280, in cache kmalloc-64 size: 64
[ 393.944197] Allocated:
[ 393.946552] PID = 2918
[ 393.948913] save_stack_trace_tsk+0x0/0x220
[ 393.953096] save_stack_trace+0x18/0x20
[ 393.956932] kasan_kmalloc+0xd8/0x188
[ 393.960594] __kmalloc+0x144/0x238
[ 393.963994] jffs2_selected_compress+0x48/0x2a0
[ 393.968524] jffs2_compress+0x58/0x478
[ 393.972273] jffs2_write_inode_range+0x13c/0x450
[ 393.976889] jffs2_write_end+0x2a8/0x4a0
[ 393.980810] generic_perform_write+0x1c0/0x280
[ 393.985251] __generic_file_write_iter+0x1c4/0x228
[ 393.990040] generic_file_write_iter+0x138/0x288
[ 393.994655] __vfs_write+0x1b4/0x238
[ 393.998228] vfs_write+0xd0/0x238
[ 394.001543] SyS_write+0xa0/0x110
[ 394.004856] __sys_trace_return+0x0/0x4
[ 394.008684] Freed:
[ 394.010691] PID = 2918
[ 394.013051] save_stack_trace_tsk+0x0/0x220
[ 394.017233] save_stack_trace+0x18/0x20
[ 394.021069] kasan_slab_free+0x88/0x188
[ 394.024902] kfree+0x6c/0x1d8
[ 394.027868] jffs2_sum_write_sumnode+0x2c4/0x880
[ 394.032486] jffs2_do_reserve_space+0x198/0x598
[ 394.037016] jffs2_reserve_space+0x3f8/0x4d8
[ 394.041286] jffs2_write_inode_range+0xf0/0x450
[ 394.045816] jffs2_write_end+0x2a8/0x4a0
[ 394.049737] generic_perform_write+0x1c0/0x280
[ 394.054179] __generic_file_write_iter+0x1c4/0x228
[ 394.058968] generic_file_write_iter+0x138/0x288
[ 394.063583] __vfs_write+0x1b4/0x238
[ 394.067157] vfs_write+0xd0/0x238
[ 394.070470] SyS_write+0xa0/0x110
[ 394.073783] __sys_trace_return+0x0/0x4
[ 394.077612] Memory state around the buggy address:
[ 394.082404] ffff800062e3b180: 00 00 00 00 00 00 00 00 fc fc fc fc fc fc fc fc
[ 394.089623] ffff800062e3b200: 00 00 00 00 00 00 00 00 fc fc fc fc fc fc fc fc
[ 394.096842] >ffff800062e3b280: 01 fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 394.104056] ^
[ 394.107283] ffff800062e3b300: fb fb fb fb fb fb fb fb fc fc fc fc fc fc fc fc
[ 394.114502] ffff800062e3b380: fb fb fb fb fb fb fb fb fc fc fc fc fc fc fc fc
[ 394.121718] ==================================================================
Signed-off-by: Yang Yang <yang.yang29@zte.com.cn> Cc: Joel Stanley <joel@jms.id.au> Signed-off-by: Richard Weinberger <richard@nod.at> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A few archs like powerpc have different errno.h values for macros
EDEADLOCK and EDEADLK. In code including both libc and linux versions of
errno.h, this can result in multiple definitions of EDEADLOCK in the
include chain. Definitions to the same value (e.g. seen with mips) do
not raise warnings, but on powerpc there are redefinitions changing the
value, which raise warnings and errors (if using "-Werror").
Guard against these redefinitions to avoid build errors like the following,
first seen cross-compiling libbpf v5.8.9 for powerpc using GCC 8.4.0 with
musl 1.1.24:
In file included from ../../arch/powerpc/include/uapi/asm/errno.h:5,
from ../../include/linux/err.h:8,
from libbpf.c:29:
../../include/uapi/asm-generic/errno.h:40: error: "EDEADLOCK" redefined [-Werror]
#define EDEADLOCK EDEADLK
In file included from toolchain-powerpc_8540_gcc-8.4.0_musl/include/errno.h:10,
from libbpf.c:26:
toolchain-powerpc_8540_gcc-8.4.0_musl/include/bits/errno.h:58: note: this is the location of the previous definition
#define EDEADLOCK 58
During the EEH MMIO error checking, the current implementation fails to map
the (virtual) MMIO address back to the pci device on radix with hugepage
mappings for I/O. This results into failure to dispatch EEH event with no
recovery even when EEH capability has been enabled on the device.
In case of hugepage mappings, eeh_token_to_phys() has a bug in virt -> phys
translation that results in wrong physical address, which is then passed to
eeh_addr_cache_get_dev() to match it against cached pci I/O address ranges
to get to a PCI device. Hence, it fails to find a match and the EEH event
never gets dispatched leaving the device in failed state.
The commit 33439620680be ("powerpc/eeh: Handle hugepages in ioremap space")
introduced following logic to translate virt to phys for hugepage mappings:
eeh_token_to_phys():
+ pa = pte_pfn(*ptep);
+
+ /* On radix we can do hugepage mappings for io, so handle that */
+ if (hugepage_shift) {
+ pa <<= hugepage_shift; <= This is wrong
+ pa |= token & ((1ul << hugepage_shift) - 1);
+ }
This patch fixes the virt -> phys translation in eeh_token_to_phys()
function.
$ cat /sys/kernel/debug/powerpc/eeh_address_cache
mem addr range [0x0000040080000000-0x00000400807fffff]: 0030:01:00.1
mem addr range [0x0000040080800000-0x0000040080ffffff]: 0030:01:00.1
mem addr range [0x0000040081000000-0x00000400817fffff]: 0030:01:00.0
mem addr range [0x0000040081800000-0x0000040081ffffff]: 0030:01:00.0
mem addr range [0x0000040082000000-0x000004008207ffff]: 0030:01:00.1
mem addr range [0x0000040082080000-0x00000400820fffff]: 0030:01:00.0
mem addr range [0x0000040082100000-0x000004008210ffff]: 0030:01:00.1
mem addr range [0x0000040082110000-0x000004008211ffff]: 0030:01:00.0
Above is the list of cached io address ranges of pci 0030:01:00.<fn>.
Before this patch:
Tracing 'arg1' of function eeh_addr_cache_get_dev() during error injection
clearly shows that 'addr=' contains wrong physical address:
KASAN report a slab-out-of-bounds problem. The logs are listed below.
It is because in function jffs2_scan_dirent_node, we alloc "checkedlen+1"
bytes for fd->name and we check crc with length rd->nsize. If checkedlen
is less than rd->nsize, it will cause the slab-out-of-bounds problem.
jffs2: Dirent at *** has zeroes in name. Truncating to %d char
==================================================================
BUG: KASAN: slab-out-of-bounds in crc32_le+0x1ce/0x260 at addr ffff8800842cf2d1
Read of size 1 by task test_JFFS2/915
=============================================================================
BUG kmalloc-64 (Tainted: G B O ): kasan: bad access detected
-----------------------------------------------------------------------------
INFO: Allocated in jffs2_alloc_full_dirent+0x2a/0x40 age=0 cpu=1 pid=915
___slab_alloc+0x580/0x5f0
__slab_alloc.isra.24+0x4e/0x64
__kmalloc+0x170/0x300
jffs2_alloc_full_dirent+0x2a/0x40
jffs2_scan_eraseblock+0x1ca4/0x3b64
jffs2_scan_medium+0x285/0xfe0
jffs2_do_mount_fs+0x5fb/0x1bbc
jffs2_do_fill_super+0x245/0x6f0
jffs2_fill_super+0x287/0x2e0
mount_mtd_aux.isra.0+0x9a/0x144
mount_mtd+0x222/0x2f0
jffs2_mount+0x41/0x60
mount_fs+0x63/0x230
vfs_kern_mount.part.6+0x6c/0x1f4
do_mount+0xae8/0x1940
SyS_mount+0x105/0x1d0
INFO: Freed in jffs2_free_full_dirent+0x22/0x40 age=27 cpu=1 pid=915
__slab_free+0x372/0x4e4
kfree+0x1d4/0x20c
jffs2_free_full_dirent+0x22/0x40
jffs2_build_remove_unlinked_inode+0x17a/0x1e4
jffs2_do_mount_fs+0x1646/0x1bbc
jffs2_do_fill_super+0x245/0x6f0
jffs2_fill_super+0x287/0x2e0
mount_mtd_aux.isra.0+0x9a/0x144
mount_mtd+0x222/0x2f0
jffs2_mount+0x41/0x60
mount_fs+0x63/0x230
vfs_kern_mount.part.6+0x6c/0x1f4
do_mount+0xae8/0x1940
SyS_mount+0x105/0x1d0
entry_SYSCALL_64_fastpath+0x1e/0x97
Call Trace:
[<ffffffff815befef>] dump_stack+0x59/0x7e
[<ffffffff812d1d65>] print_trailer+0x125/0x1b0
[<ffffffff812d82c8>] object_err+0x34/0x40
[<ffffffff812dadef>] kasan_report.part.1+0x21f/0x534
[<ffffffff81132401>] ? vprintk+0x2d/0x40
[<ffffffff815f1ee2>] ? crc32_le+0x1ce/0x260
[<ffffffff812db41a>] kasan_report+0x26/0x30
[<ffffffff812d9fc1>] __asan_load1+0x3d/0x50
[<ffffffff815f1ee2>] crc32_le+0x1ce/0x260
[<ffffffff814764ae>] ? jffs2_alloc_full_dirent+0x2a/0x40
[<ffffffff81485cec>] jffs2_scan_eraseblock+0x1d0c/0x3b64
[<ffffffff81488813>] ? jffs2_scan_medium+0xccf/0xfe0
[<ffffffff81483fe0>] ? jffs2_scan_make_ino_cache+0x14c/0x14c
[<ffffffff812da3e9>] ? kasan_unpoison_shadow+0x35/0x50
[<ffffffff812da3e9>] ? kasan_unpoison_shadow+0x35/0x50
[<ffffffff812da462>] ? kasan_kmalloc+0x5e/0x70
[<ffffffff812d5d90>] ? kmem_cache_alloc_trace+0x10c/0x2cc
[<ffffffff818169fb>] ? mtd_point+0xf7/0x130
[<ffffffff81487dc9>] jffs2_scan_medium+0x285/0xfe0
[<ffffffff81487b44>] ? jffs2_scan_eraseblock+0x3b64/0x3b64
[<ffffffff812da3e9>] ? kasan_unpoison_shadow+0x35/0x50
[<ffffffff812da3e9>] ? kasan_unpoison_shadow+0x35/0x50
[<ffffffff812da462>] ? kasan_kmalloc+0x5e/0x70
[<ffffffff812d57df>] ? __kmalloc+0x12b/0x300
[<ffffffff812da462>] ? kasan_kmalloc+0x5e/0x70
[<ffffffff814a2753>] ? jffs2_sum_init+0x9f/0x240
[<ffffffff8148b2ff>] jffs2_do_mount_fs+0x5fb/0x1bbc
[<ffffffff8148ad04>] ? jffs2_del_noinode_dirent+0x640/0x640
[<ffffffff812da462>] ? kasan_kmalloc+0x5e/0x70
[<ffffffff81127c5b>] ? __init_rwsem+0x97/0xac
[<ffffffff81492349>] jffs2_do_fill_super+0x245/0x6f0
[<ffffffff81493c5b>] jffs2_fill_super+0x287/0x2e0
[<ffffffff814939d4>] ? jffs2_parse_options+0x594/0x594
[<ffffffff81819bea>] mount_mtd_aux.isra.0+0x9a/0x144
[<ffffffff81819eb6>] mount_mtd+0x222/0x2f0
[<ffffffff814939d4>] ? jffs2_parse_options+0x594/0x594
[<ffffffff81819c94>] ? mount_mtd_aux.isra.0+0x144/0x144
[<ffffffff81258757>] ? free_pages+0x13/0x1c
[<ffffffff814fa0ac>] ? selinux_sb_copy_data+0x278/0x2e0
[<ffffffff81492b35>] jffs2_mount+0x41/0x60
[<ffffffff81302fb7>] mount_fs+0x63/0x230
[<ffffffff8133755f>] ? alloc_vfsmnt+0x32f/0x3b0
[<ffffffff81337f2c>] vfs_kern_mount.part.6+0x6c/0x1f4
[<ffffffff8133ceec>] do_mount+0xae8/0x1940
[<ffffffff811b94e0>] ? audit_filter_rules.constprop.6+0x1d10/0x1d10
[<ffffffff8133c404>] ? copy_mount_string+0x40/0x40
[<ffffffff812cbf78>] ? alloc_pages_current+0xa4/0x1bc
[<ffffffff81253a89>] ? __get_free_pages+0x25/0x50
[<ffffffff81338993>] ? copy_mount_options.part.17+0x183/0x264
[<ffffffff8133e3a9>] SyS_mount+0x105/0x1d0
[<ffffffff8133e2a4>] ? copy_mnt_ns+0x560/0x560
[<ffffffff810e8391>] ? msa_space_switch_handler+0x13d/0x190
[<ffffffff81be184a>] entry_SYSCALL_64_fastpath+0x1e/0x97
[<ffffffff810e9274>] ? msa_space_switch+0xb0/0xe0
Memory state around the buggy address: ffff8800842cf180: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc ffff8800842cf200: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
>ffff8800842cf280: fc fc fc fc fc fc 00 00 00 00 01 fc fc fc fc fc
^ ffff8800842cf300: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc ffff8800842cf380: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
==================================================================
If the pNFS layout segment is marked with the NFS_LSEG_LAYOUTRETURN
flag, then the assumption is that it has some reporting requirement
to perform through a layoutreturn (e.g. flexfiles layout stats or error
information).
Fixes: 6d597e175012 ("pnfs: only tear down lsegs that precede seqid in LAYOUTRETURN args") Cc: stable@vger.kernel.org Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
the pointer to struct dst_entry is used as pointer to struct rtable: this
turns the access to struct members like rt_mtu_locked into an OOB read in
the stack. Fix this changing the temporary variable used for IPv4 packets
in ovs_fragment(), similarly to what is done for IPv6 few lines below.
Fixes: d52e5a7e7ca4 ("ipv4: lock mtu in fnhe when received PMTU < net.ipv4.route.min_pmt") Cc: <stable@vger.kernel.org> Acked-by: Eelco Chaudron <echaudro@redhat.com> Signed-off-by: Davide Caratti <dcaratti@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The arm64 assembler in binutils 2.32 and above generates a program
property note in a note section, .note.gnu.property, to encode used x86
ISAs and features. But the kernel linker script only contains a single
NOTE segment:
In snd_sb_qsound_build, snd_ctl_add(..,p->qsound_switch...) and
snd_ctl_add(..,p->qsound_space..) are called. But the second
arguments of snd_ctl_add() could be freed via snd_ctl_add_replace()
->snd_ctl_free_one(). After the error code is returned,
snd_sb_qsound_destroy(p) is called in __error branch.
But in snd_sb_qsound_destroy(), the freed p->qsound_switch and
p->qsound_space are still used by snd_ctl_remove().
My patch set p->qsound_switch and p->qsound_space to NULL if
snd_ctl_add() failed to avoid the uaf bugs. But these codes need
to further be improved with the code style.
In snd_emu8000_create_mixer, the callee snd_ctl_add(..,emu->controls[i])
calls snd_ctl_add_replace(.., kcontrol,..). Inside snd_ctl_add_replace(),
if error happens, kcontrol will be freed by snd_ctl_free_one(kcontrol).
Then emu->controls[i] points to a freed memory, and the execution comes
to __error branch of snd_emu8000_create_mixer. The freed emu->controls[i]
is used in snd_ctl_remove(card, emu->controls[i]).
My patch set emu->controls[i] to NULL if snd_ctl_add() failed to avoid
the uaf.
Since the 'mfs' member has been declared as 'u32' in include/scsi/libfc.h,
use the %u format specifier instead of %hu. This patch fixes the following
clang compiler warning:
warning: format specifies type
'unsigned short' but the argument has type 'u32' (aka 'unsigned int')
[-Wformat]
"lport->mfs:%hu\n", mfs, lport->mfs);
~~~ ^~~~~~~~~~
%u
Link: https://lore.kernel.org/r/20210415220826.29438-8-bvanassche@acm.org Cc: Hannes Reinecke <hare@suse.de> Signed-off-by: Bart Van Assche <bvanassche@acm.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fix a crash caused by a double put on the node when the driver completed an
ACC for an unsolicted abort on the same node. The second put was executed
by lpfc_nlp_not_used() and is wrong because the completion routine executes
the nlp_put when the iocbq was released. Additionally, the driver is
issuing a LOGO then immediately calls lpfc_nlp_set_state to put the node
into NPR. This call does nothing.
Remove the lpfc_nlp_not_used call and additional set_state in the
completion routine. Remove the lpfc_nlp_set_state post issue_logo. Isn't
necessary.
Link: https://lore.kernel.org/r/20210412013127.2387-3-jsmart2021@gmail.com Co-developed-by: Justin Tee <justin.tee@broadcom.com> Signed-off-by: Justin Tee <justin.tee@broadcom.com> Signed-off-by: James Smart <jsmart2021@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Leaving this at a close-to-maximum register value 0xFFF0 means it takes
very long for the MDSS to generate a software vsync interrupt when the
hardware TE interrupt doesn't arrive. Configuring this to double the
vtotal (like some downstream kernels) leads to a frame to take at most
twice before the vsync signal, until hardware TE comes up.
In this case the hardware interrupt responsible for providing this
signal - "disp-te" gpio - is not hooked up to the mdp5 vsync/pp logic at
all. This solves severe panel update issues observed on at least the
Xperia Loire and Tone series, until said gpio is properly hooked up to
an irq.
Suggested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org> Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org> Link: https://lore.kernel.org/r/20210406214726.131534-2-marijn.suijten@somainline.org Signed-off-by: Rob Clark <robdclark@chromium.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
For two of the supported sensors the stv06xx driver allocates memory which
is stored in sd->sensor_priv. This memory is freed on a disconnect, but if
the probe() fails, then it isn't freed and so this leaks memory.
Add a new probe_error() op that drivers can use to free any allocated
memory in case there was a probe failure.
Thanks to Pavel Skripkin <paskripkin@gmail.com> for discovering the cause
of the memory leak.
In case of error in dvb_usb_adapter_dvb_init() or
dvb_usb_adapter_dvb_init() d->num_adapters_initialized won't be
incremented, but dvb_usb_adapter_exit() relies on it:
for (n = 0; n < d->num_adapters_initialized; n++)
So, allocated objects won't be freed.
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com> Reported-by: syzbot+3c2be7424cea3b932b0e@syzkaller.appspotmail.com Signed-off-by: Sean Young <sean@mess.org> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
This driver's remove path calls cancel_delayed_work(). However, that
function does not wait until the work function finishes. This means
that the callback function may still be running after the driver's
remove function has finished, which would result in a use-after-free.
Fix by calling cancel_delayed_work_sync(), which ensures that
the work is properly cancelled, no longer running, and unable
to re-schedule itself.
Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
This driver's remove path calls cancel_delayed_work(). However, that
function does not wait until the work function finishes. This means
that the callback function may still be running after the driver's
remove function has finished, which would result in a use-after-free.
Fix by calling cancel_delayed_work_sync(), which ensures that
the work is properly cancelled, no longer running, and unable
to re-schedule itself.
Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
This driver's remove path calls cancel_delayed_work(). However, that
function does not wait until the work function finishes. This means
that the callback function may still be running after the driver's
remove function has finished, which would result in a use-after-free.
Fix by calling cancel_delayed_work_sync(), which ensures that
the work is properly cancelled, no longer running, and unable
to re-schedule itself.
Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
This driver's remove path calls cancel_delayed_work(). However, that
function does not wait until the work function finishes. This means
that the callback function may still be running after the driver's
remove function has finished, which would result in a use-after-free.
Fix by calling cancel_delayed_work_sync(), which ensures that
the work is properly cancelled, no longer running, and unable
to re-schedule itself.
Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
This driver's remove path calls cancel_delayed_work(). However, that
function does not wait until the work function finishes. This means
that the callback function may still be running after the driver's
remove function has finished, which would result in a use-after-free.
Fix by calling cancel_delayed_work_sync(), which ensures that
the work is properly cancelled, no longer running, and unable
to re-schedule itself.
Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
If some error occurs, URB buffers should also be freed. If they aren't
freed with the dvb here, the em28xx_dvb_fini call doesn't frees the URB
buffers as dvb is set to NULL. The function in which error occurs should
do all the cleanup for the allocations it had done.
Tested the patch with the reproducer provided by syzbot. This patch
fixes the memleak.
Reported-by: syzbot+889397c820fa56adf25d@syzkaller.appspotmail.com Signed-off-by: Muhammad Usama Anjum <musamaanjum@gmail.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Some arrays return ILLEGAL_REQUEST with ASC 00h if they don't support the
RTPG extended header so remove the check for INVALID FIELD IN CDB.
Link: https://lore.kernel.org/r/20210331201154.20348-1-emilne@redhat.com Reviewed-by: Hannes Reinecke <hare@suse.de> Signed-off-by: Ewan D. Milne <emilne@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
CID 361199 (#1 of 1): Unchecked return value (CHECKED_RETURN)
3. check_return: Calling qla24xx_get_isp_stats without checking return
value (as is done elsewhere 4 out of 5 times).
Link: https://lore.kernel.org/r/20210320232359.941-7-bvanassche@acm.org Cc: Quinn Tran <qutran@marvell.com> Cc: Mike Christie <michael.christie@oracle.com> Cc: Himanshu Madhani <himanshu.madhani@oracle.com> Cc: Daniel Wagner <dwagner@suse.de> Cc: Lee Duncan <lduncan@suse.com> Reviewed-by: Daniel Wagner <dwagner@suse.de> Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com> Signed-off-by: Bart Van Assche <bvanassche@acm.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Add a fix for the memory leak bugs that can occur when the
saa7164_encoder_register() function fails.
The function allocates memory without explicitly freeing
it when errors occur.
Add a better error handling that deallocate the unused buffers before the
function exits during a fail.
Signed-off-by: Daniel Niv <danielniv3@gmail.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When the jack is partially inserted and then removed again it may be
removed while the hpdet code is running. In this case the following
may happen:
1. The "JACKDET rise" or ""JACKDET fall" IRQ triggers
2. arizona_jackdet runs and takes info->lock
3. The "HPDET" IRQ triggers
4. arizona_hpdet_irq runs, blocks on info->lock
5. arizona_jackdet calls arizona_stop_mic() and clears info->hpdet_done
6. arizona_jackdet releases info->lock
7. arizona_hpdet_irq now can continue running and:
7.1 Calls arizona_start_mic() (if a mic was detected)
7.2 sets info->hpdet_done
Step 7 is undesirable / a bug:
7.1 causes the device to stay in a high power-state (with MICVDD enabled)
7.2 causes hpdet to not run on the next jack insertion, which in turn
causes the EXTCON_JACK_HEADPHONE state to never get set
This fixes both issues by skipping these 2 steps when arizona_hpdet_irq
runs after the jack has been unplugged.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com> Tested-by: Charles Keepax <ckeepax@opensource.cirrus.com> Acked-by: Chanwoo Choi <cw00.choi@samsung.com> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
This fixes a compilation warning in pscsi_complete_cmd():
drivers/target/target_core_pscsi.c: In function ‘pscsi_complete_cmd’:
drivers/target/target_core_pscsi.c:624:5: warning: suggest braces around empty body in an ‘if’ statement [-Wempty-body]
; /* XXX: TCM_LOGICAL_UNIT_COMMUNICATION_FAILURE */
Link: https://lore.kernel.org/r/20210228055645.22253-5-chaitanya.kulkarni@wdc.com Reviewed-by: Mike Christie <michael.christie@oracle.com> Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com> Signed-off-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
This driver's remove path calls cancel_delayed_work(). However, that
function does not wait until the work function finishes. This means
that the callback function may still be running after the driver's
remove function has finished, which would result in a use-after-free.
Fix by calling cancel_delayed_work_sync(), which ensures that
the work is properly cancelled, no longer running, and unable
to re-schedule itself.
Call spi_master_get() holds the reference count to master device, thus
we need an additional spi_master_put() call to reduce the reference
count, otherwise we will leak a reference to master.
This commit fix it by removing the unnecessary spi_master_get().
Call spi_master_get() holds the reference count to master device, thus
we need an additional spi_master_put() call to reduce the reference
count, otherwise we will leak a reference to master.
This commit fix it by removing the unnecessary spi_master_get().
When cross-compiling with Clang, the `$(CLANG_FLAGS)' variable
contains additional flags needed to build C and assembly sources
for the target platform. Normally this variable is automatically
included in `$(KBUILD_CFLAGS)' via the top-level Makefile.
The x86 real-mode makefile builds `$(REALMODE_CFLAGS)' from a
plain assignment and therefore drops the Clang flags. This causes
Clang to not recognize x86-specific assembler directives:
Explicit propagation of `$(CLANG_FLAGS)' to `$(REALMODE_CFLAGS)',
which is inherited by real-mode make rules, fixes cross-compilation
with Clang for x86 targets.
Relevant flags:
* `--target' sets the target architecture when cross-compiling. This
flag must be set for both compilation and assembly (`KBUILD_AFLAGS')
to support architecture-specific assembler directives.
* `-no-integrated-as' tells clang to assemble with GNU Assembler
instead of its built-in LLVM assembler. This flag is set by default
unless `LLVM_IAS=1' is set, because the LLVM assembler can't yet
parse certain GNU extensions.
It should not be necessary to update the current_state field of
struct pci_dev in pci_enable_device_flags() before calling
do_pci_enable_device() for the device, because none of the
code between that point and the pci_set_power_state() call in
do_pci_enable_device() invoked later depends on it.
Moreover, doing that is actively harmful in some cases. For example,
if the given PCI device depends on an ACPI power resource whose _STA
method initially returns 0 ("off"), but the config space of the PCI
device is accessible and the power state retrieved from the
PCI_PM_CTRL register is D0, the current_state field in the struct
pci_dev representing that device will get out of sync with the
power.state of its ACPI companion object and that will lead to
power management issues going forward.
To avoid such issues it is better to leave the current_state value
as is until it is changed to PCI_D0 by do_pci_enable_device() as
appropriate. However, the power state of the device is not changed
to PCI_D0 if it is already enabled when pci_enable_device_flags()
gets called for it, so update its current_state in that case, but
use pci_update_current_state() covering platform PM too for that.
Link: https://lore.kernel.org/lkml/20210314000439.3138941-1-luzmaximilian@gmail.com/ Reported-by: Maximilian Luz <luzmaximilian@gmail.com> Tested-by: Maximilian Luz <luzmaximilian@gmail.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Some hosts incorrectly use sub-minor version for minor version (i.e.
0x02 instead of 0x20 for bcdUSB 0x320 and 0x01 for bcdUSB 0x310).
Currently the xHCI driver works around this by just checking for minor
revision > 0x01 for USB 3.1 everywhere. With the addition of USB 3.2,
checking this gets a bit cumbersome. Since there is no USB release with
bcdUSB 0x301 to 0x309, we can assume that sub-minor version 01 to 09 is
incorrect. Let's try to fix this and use the minor revision that matches
with the USB/xHCI spec to help with the version checking within the
driver.
The current dwc3_gadget_reset_interrupt() will stop any active
transfers, but only addresses blocking of EP queuing for while we are
coming from a disconnected scenario, i.e. after receiving the disconnect
event. If the host decides to issue a bus reset on the device, the
connected parameter will still be set to true, allowing for EP queuing
to continue while we are disabling the functions. To avoid this, set the
connected flag to false until the stop active transfers is complete.
Patch adds extra checking for bInterval passed by configfs.
The 5.6.4 chapter of USB Specification (rev. 2.0) say:
"A high-bandwidth endpoint must specify a period of 1x125 µs
(i.e., a bInterval value of 1)."
The issue was observed during testing UVC class on CV.
I treat this change as improvement because we can control
bInterval by configfs.
Use kzalloc() rather than kmalloc() for the dynamically allocated parts
of the colormap in fb_alloc_cmap_gfp, to prevent a leak of random kernel
data to userspace under certain circumstances.
When creating a subvolume we allocate an extent buffer for its root node
after starting a transaction. We setup a root item for the subvolume that
points to that extent buffer and then attempt to insert the root item into
the root tree - however if that fails, due to ENOMEM for example, we do
not free the extent buffer previously allocated and we do not abort the
transaction (as at that point we did nothing that can not be undone).
This means that we effectively do not return the metadata extent back to
the free space cache/tree and we leave a delayed reference for it which
causes a metadata extent item to be added to the extent tree, in the next
transaction commit, without having backreferences. When this happens
'btrfs check' reports the following:
$ btrfs check /dev/sdi
Opening filesystem to check...
Checking filesystem on /dev/sdi
UUID: dce2cb9d-025f-4b05-a4bf-cee0ad3785eb
[1/7] checking root items
[2/7] checking extents
ref mismatch on [30425088 16384] extent item 1, found 0
backref 30425088 root 256 not referenced back 0x564a91c23d70
incorrect global backref count on 30425088 found 1 wanted 0
backpointer mismatch on [30425088 16384]
owner ref check failed [30425088 16384]
ERROR: errors found in extent allocation tree or chunk allocation
[3/7] checking free space cache
[4/7] checking fs roots
[5/7] checking only csums items (without verifying data)
[6/7] checking root refs
[7/7] checking quota groups skipped (not enabled on this FS)
found 212992 bytes used, error(s) found
total csum bytes: 0
total tree bytes: 131072
total fs tree bytes: 32768
total extent tree bytes: 16384
btree space waste bytes: 124669
file data blocks allocated: 65536
referenced 65536
So fix this by freeing the metadata extent if btrfs_insert_root() returns
an error.
CC: stable@vger.kernel.org # 4.4+ Signed-off-by: Filipe Manana <fdmanana@suse.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some of SD cards sets permanent write protection bit in their CSD register,
due to lifespan or internal problem. To avoid unnecessary I/O write
operations, let's parse the bits in the CSD during initialization and mark
the card as read only for this case.
A CMD11 is sent to the SD/SDIO card to start the voltage switch procedure
into 1.8V I/O. According to the SD spec a power cycle is needed of the
card, if it turns out that the CMD11 fails. Let's fix this, to allow a
retry of the initialization without the voltage switch, to succeed.
Note that, whether it makes sense to also retry with the voltage switch
after the power cycle is a bit more difficult to know. At this point, we
treat it like the CMD11 isn't supported and therefore we skip it when
retrying.
When mounting eCryptfs, a null "dev_name" argument to ecryptfs_mount()
causes a kernel panic if the parsed options are valid. The easiest way to
reproduce this is to call mount() from userspace with an existing
eCryptfs mount's options and a "source" argument of 0.
Error out if "dev_name" is null in ecryptfs_mount()
projects / thirdparty / kernel / stable.git / log
