When unloading driver by "modprobe -r amdgpu", one NULL pointer
dereference bug occurs in ras debugfs releasing. The cause is the
duplicated debugfs_remove, as drm debugfs_root dir has been cleaned
up already by drm_minor_unregister.
Every iteration of for_each_available_child_of_node() decrements
reference count of the previous node, however when control
is transferred from the middle of the loop, as in the case of
a return or break or goto, there is no decrement thus ultimately
resulting in a memory leak.
Fix a potential memory leak in gianfar.c by inserting of_node_put()
before the goto statement.
Issue found with Coccinelle.
Signed-off-by: Sumera Priyadarsini <sylphrenadin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Remote source MAC addresses can be set on a 'source mode' macvlan
interface via the IFLA_MACVLAN_MACADDR_DATA attribute. This commit
tightens the validation of these MAC addresses to match the validation
already performed when setting or adding a single MAC address via the
IFLA_MACVLAN_MACADDR attribute.
iproute2 uses IFLA_MACVLAN_MACADDR_DATA for its 'macvlan macaddr set'
command, and IFLA_MACVLAN_MACADDR for its 'macvlan macaddr add' command,
which demonstrates the inconsistent behaviour that this commit
addresses:
# ip link add link eth0 name macvlan0 type macvlan mode source
# ip link set link dev macvlan0 type macvlan macaddr add 01:00:00:00:00:00
RTNETLINK answers: Cannot assign requested address
# ip link set link dev macvlan0 type macvlan macaddr set 01:00:00:00:00:00
# ip -d link show macvlan0
5: macvlan0@eth0: <BROADCAST,MULTICAST,DYNAMIC,UP,LOWER_UP> mtu 1500 ...
link/ether 2e:ac:fd:2d:69:f8 brd ff:ff:ff:ff:ff:ff promiscuity 0
macvlan mode source remotes (1) 01:00:00:00:00:00 numtxqueues 1 ...
With this change, the 'set' command will (rightly) fail in the same way
as the 'add' command.
Signed-off-by: Alvin Šipraga <alsi@bang-olufsen.dk> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
FCoE adapter initialization failed for ISP8021 with the following patch
applied. In addition, reproduction of the issue the patch originally tried
to address has been unsuccessful.
NVMEAsync command is being submitted to QLA while the same NVMe controller
is in the middle of reset. The reset path has deleted the association and
freed aen_op->fcp_req.private. Add a check for this private pointer before
issuing the command.
OS boot during Boot from SAN was stuck at dracut emergency shell after
enabling NVMe driver parameter. For non-MQ support the driver was enabling
MQ. Add a check to confirm if FW supports MQ.
Multipath errors were seen during failback due to login timeout. The
remote device sent LOGO, the local host tore down the session and did
relogin. The RSCN arrived indicates remote device is going through failover
after which the relogin is in a 20s timeout phase. At this point the
driver is stuck in the relogin process. Add a fix to delete the session as
part of abort/flush the login.
On Zone Disable, certain switches would ignore all commands. This causes
timeout for both switch scan command and abort of that command. On
detection of this condition, all sessions will be shutdown.
John Garry reported 'sdebug_q_cmd_complete: scp is NULL' failures that were
mainly seen on aarch64 machines (e.g. RPi 4 with four A72 CPUs). The
problem was tracked down to a missing critical section on a "short circuit"
path. Namely, the time to process the current command so far has already
exceeded the requested command duration (i.e. the number of nanoseconds in
the ndelay parameter).
The random=1 parameter setting was pivotal in finding this error. The
failure scenario involved first taking that "short circuit" path (due to a
very short command duration) and then taking the more likely
hrtimer_start() path (due to a longer command duration). With random=1 each
command's duration is taken from the uniformly distributed [0..ndelay)
interval. The fio utility also helped by reliably generating the error
scenario at about once per minute on a RPi 4 (64 bit OS).
Link: https://lore.kernel.org/r/20200813155738.109298-1-dgilbert@interlog.com Reported-by: John Garry <john.garry@huawei.com> Reviewed-by: Lee Duncan <lduncan@suse.com> Signed-off-by: Douglas Gilbert <dgilbert@interlog.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
If somehow no interrupt notification is raised for a completed request and
its doorbell bit is cleared by host, UFS driver needs to cleanup its
outstanding bit in ufshcd_abort(). Otherwise, system may behave abnormally
in the following scenario:
After ufshcd_abort() returns, this request will be requeued by SCSI layer
with its outstanding bit set. Any future completed request will trigger
ufshcd_transfer_req_compl() to handle all "completed outstanding bits". At
this time the "abnormal outstanding bit" will be detected and the "requeued
request" will be chosen to execute request post-processing flow. This is
wrong because this request is still "alive".
Link: https://lore.kernel.org/r/20200811141859.27399-2-huobean@gmail.com Reviewed-by: Can Guo <cang@codeaurora.org> Acked-by: Avri Altman <avri.altman@wdc.com> Signed-off-by: Stanley Chu <stanley.chu@mediatek.com> Signed-off-by: Bean Huo <beanhuo@micron.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In ufshcd_suspend(), after clk-gating is suspended and link is set
as Hibern8 state, ufshcd_hold() is still possibly invoked before
ufshcd_suspend() returns. For example, MediaTek's suspend vops may
issue UIC commands which would call ufshcd_hold() during the command
issuing flow.
Now if UFSHCD_CAP_HIBERN8_WITH_CLK_GATING capability is enabled,
then ufshcd_hold() may enter infinite loops because there is no
clk-ungating work scheduled or pending. In this case, ufshcd_hold()
shall just bypass, and keep the link as Hibern8 state.
Link: https://lore.kernel.org/r/20200809050734.18740-1-stanley.chu@mediatek.com Reviewed-by: Avri Altman <avri.altman@wdc.com> Co-developed-by: Andy Teng <andy.teng@mediatek.com> Signed-off-by: Andy Teng <andy.teng@mediatek.com> Signed-off-by: Stanley Chu <stanley.chu@mediatek.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
ixgbe_fcoe_ddp_setup() can be called from the main I/O path and is called
with a spin_lock held, so we have to use GFP_ATOMIC allocation instead of
GFP_KERNEL.
h1 is initially configured to reach h2 via r1 rather than the
more direct path through r2. If rp_filter is set and inherited
for r2, forwarding fails since the source address of h1 is
reachable from eth0 vs the packet coming to it via r1 and eth1.
Since rp_filter setting affects the test, explicitly reset it.
Signed-off-by: David Ahern <dsahern@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Some devices have broken extension unit where getting current value
doesn't work. Attempt that once when creating mixer control for it. If
it fails, just ignore it, so that it won't cripple the device entirely
(and/or make the error floods).
The driver supports WM1811, WM8994, WM8958 devices but according to
documentation and the regmap definitions the WM8958_DSP2_* registers
are only available on WM8958. In current code these registers are
being accessed as if they were available on all the three chips.
When starting playback on WM1811 CODEC multiple errors like:
"wm8994-codec wm8994-codec: ASoC: error at soc_component_read_no_lock on wm8994-codec: -5"
can be seen, which is caused by attempts to read an unavailable
WM8958_DSP2_PROGRAM register. The issue has been uncovered by recent
commit "e2329ee ASoC: soc-component: add soc_component_err()".
This patch adds a check in wm8958_aif_ev() callback so the DSP2 handling
is only done for WM8958.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com> Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com> Link: https://lore.kernel.org/r/20200731173834.23832-1-s.nawrocki@samsung.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The scanning through subchannels during the time of an event could
take significant amount of time in case of platforms with lots of
known subchannels. This might result in higher scheduling latencies
for other tasks especially on systems with a single CPU. Add
cond_resched() call, as the loop in slow_eval_known_fn() can be
executed for a longer duration.
The very quiet and distorted headphone output bug that afflicted my
Samsung Notebook 9 is appearing in many other Samsung laptops. Expose
the quirk which fixed my laptop as a model so other users can try it.
This driver expects upper layers to include a pseudo header of 1 byte
when passing down a skb for transmission. This driver will read this
1-byte header. This patch added a skb->len check before reading the
header to make sure the header exists.
2. Added needed_headroom and set hard_header_len to 0
When this driver transmits data,
first this driver will remove a pseudo header of 1 byte,
then the lapb module will prepend the LAPB header of 2 or 3 bytes.
So the value of needed_headroom in this driver should be 3 - 1.
Because this driver has no header_ops, according to the logic of
af_packet.c, the value of hard_header_len should be 0.
Reason of setting needed_headroom and hard_header_len at this place:
This driver is written using the API of the hdlc module, the hdlc
module enables this driver (the protocol driver) to run on any hardware
that has a driver (the hardware driver) written using the API of the
hdlc module.
Two other hdlc protocol drivers - hdlc_ppp and hdlc_raw_eth, also set
things like hard_header_len at this place. In hdlc_ppp, it sets
hard_header_len after attach_hdlc_protocol and before setting dev->type.
In hdlc_raw_eth, it sets hard_header_len by calling ether_setup after
attach_hdlc_protocol and after memcpy the settings.
3. Reset needed_headroom when detaching protocols (in hdlc.c)
When detaching a protocol from a hardware device, the hdlc module will
reset various parameters of the device (including hard_header_len) to
the default values. We add needed_headroom here so that needed_headroom
will also be reset.
Cc: Willem de Bruijn <willemdebruijn.kernel@gmail.com> Cc: Martin Schiller <ms@dev.tdt.de> Cc: Andrew Hendry <andrew.hendry@gmail.com> Signed-off-by: Xie He <xie.he.0141@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
There is no guarantee to CMA's placement, so allocating a zone specific
atomic pool from CMA might return memory from a completely different
memory zone. To get around this double check CMA's placement before
allocating from it.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
When allocating coherent pool memory for an IOMMU mapping we don't care
about the DMA mask. Move the guess for the initial GFP mask into the
dma_direct_alloc_pages and pass dma_coherent_ok as a function pointer
argument so that it doesn't get applied to the IOMMU case.
Signed-off-by: Christoph Hellwig <hch@lst.de> Tested-by: Amit Pundir <amit.pundir@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Since the stack relays on receiving own packets, it was overwriting own
transmit buffer from received packets.
At least theoretically, the received echo buffer can be corrupt or
changed and the session partner can request to resend previous data. In
this case we will re-send bad data.
With this patch we will stop to overwrite own TX buffer and use it for
sanity checking.
Fix btf_dump test cases by hard-coding BPF's pointer size of 8 bytes for cases
where it's impossible to deterimne the pointer size (no long type in BTF). In
cases where it's known, validate libbpf correctly determines it as 8.
Turns out there were a few more instances where libbpf didn't save the
errno before writing an error message, causing errno to be overridden by
the printf() return and the error disappearing if logging is enabled.
This issue was triggered because mmap() and munmap() used inconsistent
length parameters; mmap() creates a new mapping of 3 * page_size, but the
length parameter set in the subsequent re-map and munmap() functions is
4 * page_size; this leads to the destruction of the process space.
To fix this issue, first create 4 pages of anonymous mapping, then do all
the mmap() with MAP_FIXED.
Another issue is that when unmap the second page fails, the length
parameter to delete tmp1 mappings should be 4 * page_size.
[Why]
Using FRAME_UPDATE will result in infopacket to be potentially updated
one frame late.
In commit stream scenarios for previously active stream, some stale
infopacket data from previous config might be erroneously sent out on
initial frame after stream is re-enabled.
[How]
Switch to using IMMEDIATE_UPDATE mode
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com> Reviewed-by: Ashley Thomas <Ashley.Thomas2@amd.com> Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
[Why]
1. There is a calculation that is using frame_time_in_us instead of
last_render_time_in_us to calculate whether choosing an LFC multiplier
would cause the inserted frame duration to be outside of range.
2. We do not handle unsigned integer subtraction correctly and it underflows
to a really large value, which causes some logic errors.
[How]
1. Fix logic to calculate 'within range' using last_render_time_in_us
2. Split out delta_from_mid_point_delta_in_us calculation to ensure
we don't underflow and wrap around
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com> Reviewed-by: Aric Cyr <Aric.Cyr@amd.com> Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
SPI registers content may have been lost upon suspend/resume sequence.
So, always compute and apply the necessary configuration in
stm32_spi_transfer_one_setup routine.
When transfer is shorter than half of the fifo, set the data packet size
up to transfer size instead of up to half of the fifo.
Check also that threshold is set at least to 1 data frame.
The caller of stm32_spi_transfer_one(), spi_transfer_one_message(),
is waiting for us to call spi_finalize_current_transfer() and will
eventually schedule a new transfer, if available.
We should guarantee that the spi controller is really available
before calling spi_finalize_current_transfer().
Move the call to spi_finalize_current_transfer() _after_ the call
to stm32_spi_disable().
If a device is hot-removed --- for example, when a physical device is
unplugged from pcie slot or a nbd device's network is shutdown ---
this can result in a BUG_ON() crash in submit_bh_wbc(). This is
because the when the block device dies, the buffer heads will have
their Buffer_Mapped flag get cleared, leading to the crash in
submit_bh_wbc.
We had attempted to work around this problem in commit a17712c8
("ext4: check superblock mapped prior to committing"). Unfortunately,
it's still possible to hit the BUG_ON(!buffer_mapped(bh)) if the
device dies between when the work-around check in ext4_commit_super()
and when submit_bh_wbh() is finally called:
Code path:
ext4_commit_super
judge if 'buffer_mapped(sbh)' is false, return <== commit a17712c8
lock_buffer(sbh)
...
unlock_buffer(sbh)
__sync_dirty_buffer(sbh,...
lock_buffer(sbh)
judge if 'buffer_mapped(sbh))' is false, return <== added by this patch
submit_bh(...,sbh)
submit_bh_wbc(...,sbh,...)
When remounting filesystem fails late during remount handling and
block_validity mount option is also changed during the remount, we fail
to restore system zone information to a state matching the mount option.
This is mostly harmless, just the block validity checking will not match
the situation described by the mount option. Make sure these two are always
consistent.
Fix it by applying the SB_LAZYTIME and SB_I_VERSION flags from *flags to
s_flags before we parse the option and use the resulting state of the
same flags in *flags at the end of successful remount.
If we free a metadata buffer which has been failed to async write out
in the background, the jbd2 checkpoint procedure will not detect this
failure in jbd2_log_do_checkpoint(), so it may lead to filesystem
inconsistency after cleanup journal tail. This patch abort the journal
if free a buffer has write_io_error flag to prevent potential further
inconsistency.
There is a risk of filesystem inconsistency if we failed to async write
back metadata buffer in the background. Because of current buffer's end
io procedure is handled by end_buffer_async_write() in the block layer,
and it only clear the buffer's uptodate flag and mark the write_io_error
flag, so ext4 cannot detect such failure immediately. In most cases of
getting metadata buffer (e.g. ext4_read_inode_bitmap()), although the
buffer's data is actually uptodate, it may still read data from disk
because the buffer's uptodate flag has been cleared. Finally, it may
lead to on-disk filesystem inconsistency if reading old data from the
disk successfully and write them out again.
This patch detect bdev mapping->wb_err when getting journal's write
access and mark the filesystem error if bdev's mapping->wb_err was
increased, this could prevent further writing and potential
inconsistency.
cr=0 is supposed to be an optimization to save CPU cycles, but if
buddy data (in memory) is not initialized then all this makes no sense
as we have to do sync IO taking a lot of cycles. Also, at cr=0
mballoc doesn't choose any available chunk. cr=1 also skips groups
using heuristic based on avg. fragment size. It's more useful to skip
such groups and switch to cr=2 where groups will be scanned for
available chunks. However, we always read the first block group in a
flex_bg so metadata blocks will get read into the first flex_bg if
possible.
Using sparse image and dm-slow virtual device of 120TB was
simulated, then the image was formatted and filled using debugfs to
mark ~85% of available space as busy. mount process w/o the patch
couldn't complete in half an hour (according to vmstat it would take
~10-11 hours). With the patch applied mount took ~20 seconds.
Lustre-bug-id: https://jira.whamcloud.com/browse/LU-12988 Signed-off-by: Alex Zhuravlev <azhuravlev@whamcloud.com> Reviewed-by: Andreas Dilger <adilger@whamcloud.com> Reviewed-by: Artem Blagodarenko <artem.blagodarenko@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Ext4 uses blkdev_get_by_dev() to get the block_device for journal device
which does check to see if the read-only block device was opened
read-only.
As a result ext4 will hapily proceed mounting the file system with
external journal on read-only device. This is bad as we would not be
able to use the journal leading to errors later on.
Instead of simply failing to mount file system in this case, treat it in
a similar way we treat internal journal on read-only device. Allow to
mount with -o noload in read-only mode.
A customer has reported a BUG_ON in ext4_clear_journal_err() hitting
during an LTP testing. Either this has been caused by a test setup
issue where the filesystem was being overwritten while LTP was mounting
it or the journal replay has overwritten the superblock with invalid
data. In either case it is preferable we don't take the machine down
with a BUG_ON. So handle the situation of unexpectedly missing
has_journal feature more gracefully. We issue warning and fail the mount
in the cases where the race window is narrow and the failed check is
most likely a programming error. In cases where fs corruption is more
likely, we do full ext4_error() handling before failing mount / remount.
Reviewed-by: Lukas Czerner <lczerner@redhat.com> Signed-off-by: Jan Kara <jack@suse.cz> Link: https://lore.kernel.org/r/20200710140759.18031-1-jack@suse.cz Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Sasha Levin <sashal@kernel.org>
Callers of __jbd2_journal_unfile_buffer() and
__jbd2_journal_refile_buffer() assume that the b_transaction is set. In
fact if it's not, we can end up with journal_head refcounting errors
leading to crash much later that might be very hard to track down. Add
asserts to make sure that is the case.
We also make sure that b_next_transaction is NULL in
__jbd2_journal_unfile_buffer() since the callers expect that as well and
we should not get into that stage in this state anyway, leading to
problems later on if we do.
Previously the stm32h7 interrupt thread cleared all non-masked interrupts.
If an interrupt was to occur during the handling of another interrupt its
flag would be unset, resulting in a lost interrupt.
This patches fixes the issue by clearing only the currently set interrupt
flags.
The build is currently broken, if COMPILE_TEST=y and PPC_PMAC=n:
linux/drivers/video/fbdev/controlfb.c: In function ‘control_set_hardware’:
linux/drivers/video/fbdev/controlfb.c:276:2: error: implicit declaration of function ‘btext_update_display’
276 | btext_update_display(p->frame_buffer_phys + CTRLFB_OFF,
| ^~~~~~~~~~~~~~~~~~~~
Fix it by including btext.h whenever CONFIG_BOOTX_TEXT is enabled.
We don't free config irq in ifcvf_free_irq() which will trigger a
BUG() in pci core since we try to free the vectors that has an
action. Fixing this by recording the config irq in ifcvf_hw structure
and free it in ifcvf_free_irq().
Fixes: e7991f376a4d ("ifcvf: implement config interrupt in IFCVF") Cc: Zhu Lingshan <lingshan.zhu@intel.com> Signed-off-by: Jason Wang <jasowang@redhat.com> Link: https://lore.kernel.org/r/20200723091254.20617-2-jasowang@redhat.com Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Reviewed-by: Zhu Lingshan <lingshan.zhu@intel.com> Fixes: e7991f376a4d ("ifcvf: implement config interrupt in IFCVF") Cc: Zhu Lingshan <a class="moz-txt-link-rfc2396E" href="mailto:lingshan.zhu@intel.com"><lingshan.zhu@intel.com></a> Signed-off-by: Jason Wang <a class="moz-txt-link-rfc2396E" href="mailto:jasowang@redhat.com"><jasowang@redhat.com></a> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently, a NACK in slave mode is set/cleared when SCL is held low by
the IP core right before the bit is about to be pushed out. This is too
late for clearing and then a NACK from the previous byte is still used
for the current one. Now, let's clear the NACK right after we detected
the STOP condition following the NACK.
Fixes: de20d1857dd6 ("i2c: rcar: add slave support") Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When commit c64ffff7a9d1 ("i2c: core: Allow empty id_table in ACPI case
as well") fixed the enumeration of I²C devices on ACPI enabled platforms
when driver has no ID table, it missed the PRP0001 support.
i2c_device_match() and i2c_acpi_match_device() differently match
driver against given device. Use acpi_driver_match_device(), that is used
in the former, in i2c_device_probe() and don't fail PRP0001 enumeration
when no ID table exist.
Fixes: c64ffff7a9d1 ("i2c: core: Allow empty id_table in ACPI case as well") BugLink: https://stackoverflow.com/q/63519678/2511795 Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The drm scheduler currently expects that the stop/start sequence is always
executed in the timeout handling, as the job at the head of the hardware
execution list is always removed from the ring mirror before the driver
function is called and only inserted back into the list when starting the
scheduler.
This adds some unnecessary overhead if the timeout handler determines
that the GPU is still executing jobs normally and just wished to extend
the timeout, but a better solution requires a major rearchitecture of the
scheduler, which is not applicable as a fix.
Fixes: 135517d3565b ("drm/scheduler: Avoid accessing freed bad job.") Signed-off-by: Lucas Stach <l.stach@pengutronix.de> Tested-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Sasha Levin <sashal@kernel.org>
If there's only one usable, non-optimized path, nvme_round_robin_path()
returns NULL, which is wrong. Fix it by falling back to "old", like in
the single optimized path case. Also, if the active path isn't changed,
there's no need to re-assign the pointer.
Fixes: 3f6e3246db0e ("nvme-multipath: fix logic for non-optimized paths") Signed-off-by: Martin Wilck <mwilck@suse.com> Signed-off-by: Martin George <marting@netapp.com> Reviewed-by: Keith Busch <kbusch@kernel.org> Signed-off-by: Sagi Grimberg <sagi@grimberg.me> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
Normally, blkcg_iolatency_exit() will free related memory in iolatency
when cleanup queue. But if blk_throtl_init() return error and queue init
fail, blkcg_iolatency_exit() will not do that for us. Then it cause
memory leak.
c616cbee97ae ("blk-mq: punt failed direct issue to dispatch list") supposed
to add request which has been through ->queue_rq() to the hw queue dispatch
list, however it adds request running out of budget or driver tag to hw queue
too. This way basically bypasses request merge, and causes too many request
dispatched to LLD, and system% is unnecessary increased.
Fixes this issue by adding request not through ->queue_rq into sw/scheduler
queue, and this way is safe because no ->queue_rq is called on this request
yet.
High %system can be observed on Azure storvsc device, and even soft lock
is observed. This patch reduces %system during heavy sequential IO,
meantime decreases soft lockup risk.
Fixes: c616cbee97ae ("blk-mq: punt failed direct issue to dispatch list") Signed-off-by: Ming Lei <ming.lei@redhat.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Bart Van Assche <bvanassche@acm.org> Cc: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
We hit a kernel panic due to a divide by 0 in nct7904_read_fan() for
the hwmon_fan_min case. Extend the check to hwmon_fan_input case as well
for safety.
Changes from v1:
- update commit description with proper ref-accounting justification
commit db37a34c563b ("block, bfq: get a ref to a group when adding it to a service tree")
introduce leak forbfq_group and blkcg_gq objects because of get/put
imbalance.
In fact whole idea of original commit is wrong because bfq_group entity
can not dissapear under us because it is referenced by child bfq_queue's
entities from here:
-> bfq_init_entity()
->bfqg_and_blkg_get(bfqg);
->entity->parent = bfqg->my_entity
So parent entity can not disappear while child entity is in tree,
and child entities already has proper protection.
This patch revert commit db37a34c563b ("block, bfq: get a ref to a group when adding it to a service tree")
bfq_group leak trace caused by bad commit:
-> blkg_alloc
-> bfq_pq_alloc
-> bfqg_get (+1)
->bfq_activate_bfqq
->bfq_activate_requeue_entity
-> __bfq_activate_entity
->bfq_get_entity
->bfqg_and_blkg_get (+1) <==== : Note1
->bfq_del_bfqq_busy
->bfq_deactivate_entity+0x53/0xc0 [bfq]
->__bfq_deactivate_entity+0x1b8/0x210 [bfq]
-> bfq_forget_entity(is_in_service = true)
entity->on_st_or_in_serv = false <=== :Note2
if (is_in_service)
return; ==> do not touch reference
-> blkcg_css_offline
-> blkcg_destroy_blkgs
-> blkg_destroy
-> bfq_pd_offline
-> __bfq_deactivate_entity
if (!entity->on_st_or_in_serv) /* true, because (Note2)
return false;
-> bfq_pd_free
-> bfqg_put() (-1, byt bfqg->ref == 2) because of (Note2)
So bfq_group and blkcg_gq will leak forever, see test-case below.
##TESTCASE_BEGIN:
#!/bin/bash
max_iters=${1:-100}
#prep cgroup mounts
mount -t tmpfs cgroup_root /sys/fs/cgroup
mkdir /sys/fs/cgroup/blkio
mount -t cgroup -o blkio none /sys/fs/cgroup/blkio
Fixes: db37a34c563b ("block, bfq: get a ref to a group when adding it to a service tree") Tested-by: Oleksandr Natalenko <oleksandr@natalenko.name> Signed-off-by: Dmitry Monakhov <dmtrmonakhov@yandex-team.ru> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
If we pass in an offset which is larger than PAGE_SIZE, then
page_is_mergeable() thinks it's not mergeable with the previous bio_vec,
leading to a large number of bio_vecs being used. Use a slightly more
obvious test that the two pages are compatible with each other.
Fixes: 52d52d1c98a9 ("block: only allow contiguous page structs in a bio_vec") Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org> Reviewed-by: Ming Lei <ming.lei@redhat.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
We need to set it to the most recent completed fence, not the most
recent submitted. Otherwise we have races where we think we can retire
submits that the GPU is not finished with, if the GPU doesn't manage to
overwrite the seqno before we look at it.
This can show up with hang recovery if one of the submits after the
crashing submit also hangs after it is replayed.
Fixes: f97decac5f4c ("drm/msm: Support multiple ringbuffers") Signed-off-by: Rob Clark <robdclark@chromium.org> Reviewed-by: Jordan Crouse <jcrouse@codeaurora.org> Signed-off-by: Rob Clark <robdclark@chromium.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
1f23816b8eb8 ("virtio_blk: add discard and write zeroes support") starts
to support multi-range discard for virtio-blk. However, the virtio-blk
disk may report max discard segment as 1, at least that is exactly what
qemu is doing.
So far, block layer switches to normal request merge if max discard segment
limit is 1, and multiple bios can be merged to single segment. This way may
cause memory corruption in virtblk_setup_discard_write_zeroes().
Fix the issue by handling single max discard segment in straightforward
way.
Fixes: 1f23816b8eb8 ("virtio_blk: add discard and write zeroes support") Signed-off-by: Ming Lei <ming.lei@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Cc: Changpeng Liu <changpeng.liu@intel.com> Cc: Daniel Verkamp <dverkamp@chromium.org> Cc: Michael S. Tsirkin <mst@redhat.com> Cc: Stefan Hajnoczi <stefanha@redhat.com> Cc: Stefano Garzarella <sgarzare@redhat.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
When queue_max_discard_segments(q) is 1, blk_discard_mergable() will
return false for discard request, then normal request merge is applied.
However, only queue_max_segments() is checked, so max discard segment
limit isn't respected.
Check max discard segment limit in the request merge code for fixing
the issue.
Discard request failure of virtio_blk is fixed.
Fixes: 69840466086d ("block: fix the DISCARD request merge") Signed-off-by: Ming Lei <ming.lei@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Cc: Stefano Garzarella <sgarzare@redhat.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
If an NFSv2/v3 client breaks an NFSv4 client's delegation, it will hit a
NULL dereference in nfsd_breaker_owns_lease().
Easily reproduceable with for example
mount -overs=4.2 server:/export /mnt/
sleep 1h </mnt/file &
mount -overs=3 server:/export /mnt2/
touch /mnt2/file
Reported-by: Robert Dinse <nanook@eskimo.com> Fixes: 28df3d1539de50 ("nfsd: clients don't need to break their own delegations") BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=208807 Signed-off-by: J. Bruce Fields <bfields@redhat.com> Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Capture and playback endpoints on Saffire 6 (USB 1.1) resides on the same
interface. This was not supported by the composite quirk back in the day
when initial support for this device was added, thus only playback was
enabled until now.
Fixes: 11e424e88bd4 ("ALSA: usb-audio: Add support for Focusrite Saffire 6 USB") Signed-off-by: Alexander Tsoy <alexander@tsoy.me> Cc: <stable.vger.kernel.org> Link: https://lore.kernel.org/r/20200815002103.29247-1-alexander@tsoy.me Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
Because intel_pstate_set_energy_pref_index() reads and writes the
MSR_HWP_REQUEST register without using the cached value of it used by
intel_pstate_hwp_boost_up() and intel_pstate_hwp_boost_down(), those
functions may overwrite the value written by it and so the EPP value
set via sysfs may be lost.
To avoid that, make intel_pstate_set_energy_pref_index() take the
cached value of MSR_HWP_REQUEST just like the other two routines
mentioned above and update it with the new EPP value coming from
user space in addition to updating the MSR.
Note that the MSR itself still needs to be updated too in case
hwp_boost is unset or the boosting mechanism is not active at the
EPP change time.
Fixes: e0efd5be63e8 ("cpufreq: intel_pstate: Add HWP boost utility and sched util hooks") Reported-by: Francisco Jerez <currojerez@riseup.net> Cc: 4.18+ <stable@vger.kernel.org> # 4.18+: 3da97d4db8ee cpufreq: intel_pstate: Rearrange ... Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Reviewed-by: Francisco Jerez <currojerez@riseup.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
To avoid some issues, for example RCU usage warning and double free,
we should flush the flows under ovs_lock. This patch refactors
table_instance_destroy and introduces table_instance_flow_flush
which can be invoked by __dp_destroy or ovs_flow_tbl_flush.
Fixes: 50b0e61b32ee ("net: openvswitch: fix possible memleak on destroy flow-table") Reported-by: Johan Knöös <jknoos@google.com>
Reported-at: https://mail.openvswitch.org/pipermail/ovs-discuss/2020-August/050489.html Signed-off-by: Tonghao Zhang <xiangxia.m.yue@gmail.com> Reviewed-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The driver using cpu_logical_map() macro which will expand to
__cpu_logical_map, we can't access it in a drvier. Let's turn
cpu_logical_map() into a C wrapper and export it to fix the
build issue.
Also create a function set_cpu_logical_map(cpu, hwid) when assign
a value to cpu_logical_map(cpu).
Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When CONFIG_EFI is not enabled, we might get an undefined reference to
efi_enter_virtual_mode() error, if this efi_enabled() call isn't inlined
into start_kernel(). This happens in particular, if start_kernel() is
annodated with __no_sanitize_address.
Reported-by: kernel test robot <lkp@intel.com> Signed-off-by: Andrey Konovalov <andreyknvl@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Acked-by: Ard Biesheuvel <ardb@kernel.org> Cc: Alexander Potapenko <glider@google.com> Cc: Andrey Ryabinin <aryabinin@virtuozzo.com> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Dmitry Vyukov <dvyukov@google.com> Cc: Elena Petrova <lenaptr@google.com> Cc: Marco Elver <elver@google.com> Cc: Vincenzo Frascino <vincenzo.frascino@arm.com> Cc: Walter Wu <walter-zh.wu@mediatek.com> Link: http://lkml.kernel.org/r/6514652d3a32d3ed33d6eb5c91d0af63bf0d1a0c.1596544734.git.andreyknvl@google.com Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Set the timeout value as per cfg80211's set_power_mgmt() request. If the
requested value value is left undefined we set it to 2 seconds, the
maximum supported value.
The initial code that was adding delays was doing a cast over undefined
memory. This meant that the delays would be all gibberish.
This change, allocates all delays on the stack, and assigns them from the
ZynqMP & Versal macros/phase-list. And then finally copies them over the
common iclk_phase & oclk_phase variables.
The char buffer buf, receives data directly from user space,
so its content might be negative and its elements are left
shifted to form an unsigned integer.
Since left shifting a negative value is undefined behavior, thus
change the char to u8 to elimintate this UB.
Fix build errors when CONFIG_PCI_MSI is not enabled by making the
driver depend on PCI_MSI:
ld: drivers/dma/idxd/device.o: in function `idxd_mask_msix_vector':
device.c:(.text+0x26f): undefined reference to `pci_msi_mask_irq'
ld: drivers/dma/idxd/device.o: in function `idxd_unmask_msix_vector':
device.c:(.text+0x2af): undefined reference to `pci_msi_unmask_irq'
The kernel test robot pointed out a slightly different error message
after recent commit 5456ffdee666 ("powerpc/spufs: simplify spufs core
dumping") to spufs for a configuration that never worked:
powerpc64-linux-ld: arch/powerpc/platforms/cell/spufs/file.o: in function `.spufs_proxydma_info_dump':
>> file.c:(.text+0x4c68): undefined reference to `.dump_emit'
powerpc64-linux-ld: arch/powerpc/platforms/cell/spufs/file.o: in function `.spufs_dma_info_dump':
file.c:(.text+0x4d70): undefined reference to `.dump_emit'
powerpc64-linux-ld: arch/powerpc/platforms/cell/spufs/file.o: in function `.spufs_wbox_info_dump':
file.c:(.text+0x4df4): undefined reference to `.dump_emit'
Add a Kconfig dependency to prevent this from happening again.
Reported-by: kernel test robot <lkp@intel.com> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Jeremy Kerr <jk@ozlabs.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20200706132302.3885935-1-arnd@arndb.de Signed-off-by: Sasha Levin <sashal@kernel.org>
__hyp_call_panic_nvhe contains inline assembly which did not declare
its dependency on the __hyp_panic_string symbol.
The static-declared string has previously been kept alive because of a use in
__hyp_call_panic_vhe. Fix this in preparation for separating the source files
between VHE and nVHE when the two users land in two different compilation
units. The static variable otherwise gets dropped when compiling the nVHE
source file, causing an undefined symbol linker error later.
According to https://www.kernel.org/doc/Documentation/gpio/consumer.txt,
- all of the gpiod_set_value_xxx() functions operate with the *logical*
value. So in imx290_power_on() the reset signal should be cleared
(de-asserted) with gpiod_set_value_cansleep(imx290->rst_gpio, 0), and in
imx290_power_off() the value of 1 must be used to apply/assert the reset
to the sensor. In the device tree the reset pin is described as
GPIO_ACTIVE_LOW, and gpiod_set_value_xxx() functions take this into
account,
- when devm_gpiod_get_optional() is called with GPIOD_ASIS, the GPIO is
not initialized, and the direction must be set later; using a GPIO
without setting its direction first is illegal and will result in undefined
behavior. Fix this by using GPIOD_OUT_HIGH instead of GPIOD_ASIS (this
asserts the reset signal to the sensor initially).
In case of errors vpif_probe_complete() releases memory for vpif_obj.sd
and unregisters the V4L2 device. But then this is done again by
vpif_probe() itself. The patch removes the cleaning from
vpif_probe_complete().
Found by Linux Driver Verification project (linuxtesting.org).
syzbot found issues with having hugetlbfs on a union/overlay as reported
in [1]. Due to the limitations (no write) and special functionality of
hugetlbfs, it does not work well in filesystem stacking. There are no
know use cases for hugetlbfs stacking. Rather than making modifications
to get hugetlbfs working in such environments, simply prevent stacking.
The Intel uncore driver may claim some of the pci ids from ie31200 which
means that the ie31200 edac driver will not initialize them as part of
pci_register_driver().
Let's add a fallback for this case to 'pci_get_device()' to get a
reference on the device such that it can still be configured. This is
similar in approach to other edac drivers.
In aio case, if the completion comes very fast just before the
ceph_read_iter() returns to fs/aio.c, the kiocb will be freed in
the completion callback, then if ceph_read_iter() access again
we will potentially hit the use-after-free bug.
[ jlayton: initialize direct_lock early, and use it everywhere ]
URL: https://tracker.ceph.com/issues/45649 Signed-off-by: Xiubo Li <xiubli@redhat.com> Signed-off-by: Jeff Layton <jlayton@kernel.org> Signed-off-by: Ilya Dryomov <idryomov@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Make sure the delayed work stopped before releasing the resources.
cancel_delayed_work_sync() will only guarantee that the work finishes
executing if the work is already in the ->worklist. That means after
the cancel_delayed_work_sync() returns, it will leave the work requeued
if it was rearmed at the end. That can lead to a use after free once the
work struct is freed.
Fix it by flushing the delayed work instead of trying to cancel it, and
ensure that the work doesn't rearm if the mdsc is stopping.
URL: https://tracker.ceph.com/issues/46293 Signed-off-by: Xiubo Li <xiubli@redhat.com> Reviewed-by: Jeff Layton <jlayton@kernel.org> Signed-off-by: Ilya Dryomov <idryomov@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / thirdparty / kernel / stable.git / log
