There is no such trigger documented or implemented in Linux. It was a
copy & paste mistake.
This fixes:
arch/arm/boot/dts/broadcom/bcm47189-luxul-xap-1440.dtb: leds: led-wlan:linux,default-trigger: 'oneOf' conditional failed, one must be fixed:
'default-off' is not one of ['backlight', 'default-on', 'heartbeat', 'disk-activity', 'disk-read', 'disk-write', 'timer', 'pattern', 'audio-micmute', 'audio-mute', 'bluetooth-power', 'flash', 'kbd-capslock', 'mtd', 'nand-disk', 'none', 'torch', 'usb-gadget', 'usb-host', 'usbport']
'default-off' does not match '^cpu[0-9]*$'
'default-off' does not match '^hci[0-9]+-power$'
'default-off' does not match '^mmc[0-9]+$'
'default-off' does not match '^phy[0-9]+tx$'
From schema: Documentation/devicetree/bindings/leds/leds-gpio.yaml
The power domain containing the Cortex-R7 CPU core on the R-Car V3H SoC
must always be in power-on state, unlike on other SoCs in the R-Car Gen3
family. See Table 9.4 "Power domains" in the R-Car Series, 3rd
Generation Hardware User’s Manual Rev.1.00 and later.
Fix this by marking the domain as a CPU domain without control
registers, so the driver will not touch it.
Ensure no remaining requests in virtqueues before resetting vdev and
deleting virtqueues. Otherwise these requests will never be completed.
It may cause the system to become unresponsive.
Function blk_mq_quiesce_queue() can ensure that requests have become
in_flight status, but it cannot guarantee that requests have been
processed by the device. Virtqueues should never be deleted before
all requests become complete status.
Function blk_mq_freeze_queue() ensure that all requests in virtqueues
become complete status. And no requests can enter in virtqueues.
If we are bus manager and the bus has inconsistent gap counts, send a
bus reset immediately instead of trying to read the root node's config
ROM first. Otherwise, we could spend a lot of time trying to read the
config ROM but never succeeding.
This eliminates a 50+ second delay before the FireWire bus is usable after
a newly connected device is powered on in certain circumstances.
The delay occurs if a gap count inconsistency occurs, we are not the root
node, and we become bus manager. One scenario that causes this is with a TI
XIO2213B OHCI, the first time a Sony DSR-25 is powered on after being
connected to the FireWire cable. In this configuration, the Linux box will
not receive the initial PHY configuration packet sent by the DSR-25 as IRM,
resulting in the DSR-25 having a gap count of 44 while the Linux box has a
gap count of 63.
FireWire devices have a gap count parameter, which is set to 63 on power-up
and can be changed with a PHY configuration packet. This determines the
duration of the subaction and arbitration gaps. For reliable communication,
all nodes on a FireWire bus must have the same gap count.
A node may have zero or more of the following roles: root node, bus manager
(BM), isochronous resource manager (IRM), and cycle master. Unless a root
node was forced with a PHY configuration packet, any node might become root
node after a bus reset. Only the root node can become cycle master. If the
root node is not cycle master capable, the BM or IRM should force a change
of root node.
After a bus reset, each node sends a self-ID packet, which contains its
current gap count. A single bus reset does not change the gap count, but
two bus resets in a row will set the gap count to 63. Because a consistent
gap count is required for reliable communication, IEEE 1394a-2000 requires
that the bus manager generate a bus reset if it detects that the gap count
is inconsistent.
When the gap count is inconsistent, build_tree() will notice this after the
self identification process. It will set card->gap_count to the invalid
value 0. If we become bus master, this will force bm_work() to send a bus
reset when it performs gap count optimization.
After a bus reset, there is no bus manager. We will almost always try to
become bus manager. Once we become bus manager, we will first determine
whether the root node is cycle master capable. Then, we will determine if
the gap count should be changed. If either the root node or the gap count
should be changed, we will generate a bus reset.
To determine if the root node is cycle master capable, we read its
configuration ROM. bm_work() will wait until we have finished trying to
read the configuration ROM.
However, an inconsistent gap count can make this take a long time.
read_config_rom() will read the first few quadlets from the config ROM. Due
to the gap count inconsistency, eventually one of the reads will time out.
When read_config_rom() fails, fw_device_init() calls it again until
MAX_RETRIES is reached. This takes 50+ seconds.
Once we give up trying to read the configuration ROM, bm_work() will wake
up, assume that the root node is not cycle master capable, and do a bus
reset. Hopefully, this will resolve the gap count inconsistency.
This change makes bm_work() check for an inconsistent gap count before
waiting for the root node's configuration ROM. If the gap count is
inconsistent, bm_work() will immediately do a bus reset. This eliminates
the 50+ second delay and rapidly brings the bus to a working state.
I considered that if the gap count is inconsistent, a PHY configuration
packet might not be successful, so it could be desirable to skip the PHY
configuration packet before the bus reset in this case. However, IEEE
1394a-2000 and IEEE 1394-2008 say that the bus manager may transmit a PHY
configuration packet before a bus reset when correcting a gap count error.
Since the standard endorses this, I decided it's safe to retain the PHY
configuration packet transmission.
Normally, after a topology change, we will reset the bus a maximum of 5
times to change the root node and perform gap count optimization. However,
if there is a gap count inconsistency, we must always generate a bus reset.
Otherwise the gap count inconsistency will persist and communication will
be unreliable. For that reason, if there is a gap count inconstency, we
generate a bus reset even if we already reached the 5 reset limit.
LUNs going into "failed ready running" state observed on >1T and on even
numbers of size (2T, 4T, 6T, 8T and 10T). The issue occurs when DIF is
enabled at the host.
The kernel logs:
Cannot setup S/G List for HBAIO segs 1/1 SGL 512 SCSI 256: 3 0
The host lpfc driver is failing to setup scatter/gather list (protection
data) for the I/Os.
The return type lpfc_bg_setup_sgl()/lpfc_bg_setup_sgl_prot() causes the
compiler to remove the most significant bit. Use an unsigned type instead.
Signed-off-by: Hannes Reinecke <hare@suse.de>
[dwagner: added commit message] Signed-off-by: Daniel Wagner <dwagner@suse.de> Link: https://lore.kernel.org/r/20231220162658.12392-1-dwagner@suse.de Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently, coretemp driver supports only 128 cores per package.
This loses some core temperature information on systems that have more
than 128 cores per package.
[ 58.685033] coretemp coretemp.0: Adding Core 128 failed
[ 58.692009] coretemp coretemp.0: Adding Core 129 failed
...
Enlarge the limitation to 512 because there are platforms with more than
256 cores per package.
In the initial boot stage the integrated keyboard of Fujitsu Lifebook U728
refuses to work and it's not possible to type for example a dm-crypt
passphrase without the help of an external keyboard.
i8042.nomux kernel parameter resolves this issue but using that a PS/2
mouse is detected. This input device is unused even when the i2c-hid-acpi
kernel module is blacklisted making the integrated ELAN touchpad
(04F3:3092) not working at all.
So this notebook uses a hid-over-i2c touchpad which is managed by the
i2c_designware input driver. Since you can't find a PS/2 mouse port on this
computer and you can't connect a PS/2 mouse to it even with an official
port replicator I think it's safe to not use the PS/2 mouse port at all.
In ext4_map_blocks(), if we can't find a range of mapping in the
extents cache, we are calling ext4_ext_map_blocks() to search the real
path and ext4_ext_determine_hole() to determine the hole range. But if
the querying range was partially or completely overlaped by a delalloc
extent, we can't find it in the real extent path, so the returned hole
length could be incorrect.
Fortunately, ext4_ext_put_gap_in_cache() have already handle delalloc
extent, but it searches start from the expanded hole_start, doesn't
start from the querying range, so the delalloc extent found could not be
the one that overlaped the querying range, plus, it also didn't adjust
the hole length. Let's just remove ext4_ext_put_gap_in_cache(), handle
delalloc and insert adjusted hole extent in ext4_ext_determine_hole().
When the target port has not active port binding, there is no point in
trying to process the command as it has to fail anyway. Instead adding
checks to all commands abort the command early.
Reviewed-by: Hannes Reinecke <hare@suse.de> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Daniel Wagner <dwagner@suse.de> Signed-off-by: Keith Busch <kbusch@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In case we return early out of __nvmet_fc_finish_ls_req() we still have
to release the reference on the target port.
Reviewed-by: Hannes Reinecke <hare@suse.de> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Daniel Wagner <dwagner@suse.de> Signed-off-by: Keith Busch <kbusch@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The first argument of list_add_tail function is the new element which
should be added to the list which is the second argument. Swap the
arguments to allow processing more than one element at a time.
Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Hannes Reinecke <hare@suse.de> Signed-off-by: Daniel Wagner <dwagner@suse.de> Signed-off-by: Keith Busch <kbusch@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The module exit path has race between deleting all controllers and
freeing 'left over IDs'. To prevent double free a synchronization
between nvme_delete_ctrl and ida_destroy has been added by the initial
commit.
There is some logic around trying to prevent from hanging forever in
wait_for_completion, though it does not handling all cases. E.g.
blktests is able to reproduce the situation where the module unload
hangs forever.
If we completely rely on the cleanup code executed from the
nvme_delete_ctrl path, all IDs will be freed eventually. This makes
calling ida_destroy unnecessary. We only have to ensure that all
nvme_delete_ctrl code has been executed before we leave
nvme_fc_exit_module. This is done by flushing the nvme_delete_wq
workqueue.
While at it, remove the unused nvme_fc_wq workqueue too.
Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Hannes Reinecke <hare@suse.de> Signed-off-by: Daniel Wagner <dwagner@suse.de> Signed-off-by: Keith Busch <kbusch@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The annotation says in sctp_new(): "If it is a shutdown ack OOTB packet, we
expect a return shutdown complete, otherwise an ABORT Sec 8.4 (5) and (8)".
However, it does not check SCTP_CID_SHUTDOWN_ACK before setting vtag[REPLY]
in the conntrack entry(ct).
Because of that, if the ct in Router disappears for some reason in [1]
with the packet sequence like below:
when processing HB ACK packet in Router it calls sctp_new() to initialize
the new ct with vtag[REPLY] set to HB_ACK packet's vtag.
Later when sending DATA from Client, all the SACKs from Server will get
dropped in Router, as the SACK packet's vtag does not match vtag[REPLY]
in the ct. The worst thing is the vtag in this ct will never get fixed
by the upcoming packets from Server.
This patch fixes it by checking SCTP_CID_SHUTDOWN_ACK before setting
vtag[REPLY] in the ct in sctp_new() as the annotation says. With this
fix, it will leave vtag[REPLY] in ct to 0 in the case above, and the
next HB REQ/ACK from Server is able to fix the vtag as its value is 0
in nf_conntrack_sctp_packet().
Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Continuous regulators can be configured to operate only in a certain
duty cycle range (for example from 0..91%). Add a check to error out if
the duty cycle translates to an unsupported (or out of range) voltage.
devm_kasprintf() returns a pointer to dynamically allocated memory
which can be NULL upon failure. Ensure the allocation was successful
by checking the pointer validity.
Places the logic for checking if the group's block bitmap is corrupt under
the protection of the group lock to avoid allocating blocks from the group
with a corrupted block bitmap.
Determine if the group block bitmap is corrupted before using ac_b_ex in
ext4_mb_try_best_found() to avoid allocating blocks from a group with a
corrupted block bitmap in the following concurrency and making the
situation worse.
ext4_mb_regular_allocator
ext4_lock_group(sb, group)
ext4_mb_good_group
// check if the group bbitmap is corrupted
ext4_mb_complex_scan_group
// Scan group gets ac_b_ex but doesn't use it
ext4_unlock_group(sb, group)
ext4_mark_group_bitmap_corrupted(group)
// The block bitmap was corrupted during
// the group unlock gap.
ext4_mb_try_best_found
ext4_lock_group(ac->ac_sb, group)
ext4_mb_use_best_found
mb_mark_used
// Allocating blocks in block bitmap corrupted group
With one of the on-board ASM1061 AHCI controllers (1b21:0612) on an
ASUSTeK Pro WS WRX80E-SAGE SE WIFI mainboard, a controller hang was
observed that was immediately preceded by the following kernel
messages:
The first message is produced by code in drivers/iommu/dma-iommu.c
which is accompanied by the following comment that seems to apply:
/*
* Try to use all the 32-bit PCI addresses first. The original SAC vs.
* DAC reasoning loses relevance with PCIe, but enough hardware and
* firmware bugs are still lurking out there that it's safest not to
* venture into the 64-bit space until necessary.
*
* If your device goes wrong after seeing the notice then likely either
* its driver is not setting DMA masks accurately, the hardware has
* some inherent bug in handling >32-bit addresses, or not all the
* expected address bits are wired up between the device and the IOMMU.
*/
Asking the ASM1061 on a discrete PCIe card to DMA from I/O virtual
address 0xffffffff00000000 produces the following I/O page faults:
Note that the upper 21 bits of the logged DMA address are zero. (When
asking a different PCIe device in the same PCIe slot to DMA to the
same I/O virtual address, we do see all the upper 32 bits of the DMA
address as 1, so this is not an issue with the chipset or IOMMU
configuration on the test system.)
Also, hacking libahci to always set the upper 21 bits of all DMA
addresses to 1 produces no discernible effect on the behavior of the
ASM1061, and mkfs/mount/scrub/etc work as without this hack.
This all strongly suggests that the ASM1061 has a 43 bit DMA address
limit, and this commit therefore adds a quirk to deal with this limit.
This issue probably applies to (some of) the other supported ASMedia
parts as well, but we limit it to the PCI IDs known to refer to
ASM1061 parts, as that's the only part we know for sure to be affected
by this issue at this point.
Link: https://lore.kernel.org/linux-ide/ZaZ2PIpEId-rl6jv@wantstofly.org/ Signed-off-by: Lennert Buytenhek <kernel@wantstofly.org>
[cassel: drop date from error messages in commit log] Signed-off-by: Niklas Cassel <cassel@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The userspace program could pass any values to the driver through
ioctl() interface. If the driver doesn't check the value of pixclock,
it may cause divide-by-zero error.
In sisfb_check_var(), var->pixclock is used as a divisor to caculate
drate before it is checked against zero. Fix this by checking it
at the beginning.
This is similar to CVE-2022-3061 in i740fb which was fixed by
commit 15cf0b8.
The userspace program could pass any values to the driver through
ioctl() interface. If the driver doesn't check the value of pixclock,
it may cause divide-by-zero error.
Although pixclock is checked in savagefb_decode_var(), but it is not
checked properly in savagefb_probe(). Fix this by checking whether
pixclock is zero in the function savagefb_check_var() before
info->var.pixclock is used as the divisor.
This is similar to CVE-2022-3061 in i740fb which was fixed by
commit 15cf0b8.
fast-xmit must only be enabled after the sta has been uploaded to the driver,
otherwise it could end up passing the not-yet-uploaded sta via drv_tx calls
to the driver, leading to potential crashes because of uninitialized drv_priv
data.
Add a missing sta->uploaded check and re-check fast xmit after inserting a sta.
dump(cb=[0, 1]):
if_start=cb[1] (=1)
send rdev0.wdev1 -> ok
// since if_start=1 the rdev0.wdev0 got skipped
// through if_idx < if_start
send rdev1.wdev1 -> ok
The if_start needs to be reset back to 0 upon wdev
loop end.
The problem is actually hard to hit on a desktop,
and even on most routers. The prerequisites for
this manifesting was:
- more than 1 wiphy
- a few handful of interfaces
- dump without rdev or wdev filter
I was seeing this with 4 wiphys 9 interfaces each.
It'd miss 6 interfaces from the last wiphy
reported to userspace.
We seem to have hit warnings of 'output may be truncated' which is fixed
by increasing the size of 'irq_name'
drivers/dma/fsl-qdma.c: In function ‘fsl_qdma_irq_init’:
drivers/dma/fsl-qdma.c:824:46: error: ‘%d’ directive writing between 1 and 11 bytes into a region of size 10 [-Werror=format-overflow=]
824 | sprintf(irq_name, "qdma-queue%d", i);
| ^~
drivers/dma/fsl-qdma.c:824:35: note: directive argument in the range [-2147483641, 2147483646]
824 | sprintf(irq_name, "qdma-queue%d", i);
| ^~~~~~~~~~~~~~
drivers/dma/fsl-qdma.c:824:17: note: ‘sprintf’ output between 12 and 22 bytes into a destination of size 20
824 | sprintf(irq_name, "qdma-queue%d", i);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
We seem to have hit warnings of 'output may be truncated' which is fixed
by increasing the size of 'dev_id'
drivers/dma/sh/shdmac.c: In function ‘sh_dmae_probe’:
drivers/dma/sh/shdmac.c:541:34: error: ‘%d’ directive output may be truncated writing between 1 and 10 bytes into a region of size 9 [-Werror=format-truncation=]
541 | "sh-dmae%d.%d", pdev->id, id);
| ^~
In function ‘sh_dmae_chan_probe’,
inlined from ‘sh_dmae_probe’ at drivers/dma/sh/shdmac.c:845:9:
drivers/dma/sh/shdmac.c:541:26: note: directive argument in the range [0, 2147483647]
541 | "sh-dmae%d.%d", pdev->id, id);
| ^~~~~~~~~~~~~~
drivers/dma/sh/shdmac.c:541:26: note: directive argument in the range [0, 19]
drivers/dma/sh/shdmac.c:540:17: note: ‘snprintf’ output between 11 and 21 bytes into a destination of size 16
540 | snprintf(sh_chan->dev_id, sizeof(sh_chan->dev_id),
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
541 | "sh-dmae%d.%d", pdev->id, id);
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
An abort that is responded to by iSCSI itself is added to tmr_list but does
not go to target core. A LUN_RESET that goes through tmr_list takes a
refcounter on the abort and waits for completion. However, the abort will
be never complete because it was not started in target core.
Unable to locate ITT: 0x05000000 on CID: 0
Unable to locate RefTaskTag: 0x05000000 on CID: 0.
wait_for_tasks: Stopping tmf LUN_RESET with tag 0x0 ref_task_tag 0x0 i_state 34 t_state ISTATE_PROCESSING refcnt 2 transport_state active,stop,fabric_stop
wait for tasks: tmf LUN_RESET with tag 0x0 ref_task_tag 0x0 i_state 34 t_state ISTATE_PROCESSING refcnt 2 transport_state active,stop,fabric_stop
...
INFO: task kworker/0:2:49 blocked for more than 491 seconds.
task:kworker/0:2 state:D stack: 0 pid: 49 ppid: 2 flags:0x00000800
Workqueue: events target_tmr_work [target_core_mod]
Call Trace:
__switch_to+0x2c4/0x470
_schedule+0x314/0x1730
schedule+0x64/0x130
schedule_timeout+0x168/0x430
wait_for_completion+0x140/0x270
target_put_cmd_and_wait+0x64/0xb0 [target_core_mod]
core_tmr_lun_reset+0x30/0xa0 [target_core_mod]
target_tmr_work+0xc8/0x1b0 [target_core_mod]
process_one_work+0x2d4/0x5d0
worker_thread+0x78/0x6c0
To fix this, only add abort to tmr_list if it will be handled by target
core.
Signed-off-by: Dmitry Bogdanov <d.bogdanov@yadro.com> Link: https://lore.kernel.org/r/20240111125941.8688-1-d.bogdanov@yadro.com Reviewed-by: Mike Christie <michael.christie@oracle.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The validation of the value written to sched_rt_period_us was broken
because:
- the sysclt_sched_rt_period is declared as unsigned int
- parsed by proc_do_intvec()
- the range is asserted after the value parsed by proc_do_intvec()
Because of this negative values written to the file were written into a
unsigned integer that were later on interpreted as large positive
integers which did passed the check:
if (sysclt_sched_rt_period <= 0)
return EINVAL;
This commit fixes the parsing by setting explicit range for both
perid_us and runtime_us into the sched_rt_sysctls table and processes
the values with proc_dointvec_minmax() instead.
Alternatively if we wanted to use full range of unsigned int for the
period value we would have to split the proc_handler and use
proc_douintvec() for it however even the
Documentation/scheduller/sched-rt-group.rst describes the range as 1 to
INT_MAX.
As far as I can tell the only problem this causes is that the sysctl
file allows writing negative values which when read back may confuse
userspace.
There is also a LTP test being submitted for these sysctl files at:
What this test does is to compare the return value from the
sched_rr_get_interval() and the sched_rr_timeslice_ms sysctl file and
fails if they do not match.
The problem it found is the intial sysctl file value which was computed as:
static int sysctl_sched_rr_timeslice = (MSEC_PER_SEC / HZ) * RR_TIMESLICE;
which works fine as long as MSEC_PER_SEC is multiple of HZ, however it
introduces 10% rounding error for CONFIG_HZ_300:
(MSEC_PER_SEC / HZ) * (100 * HZ / 1000)
(1000 / 300) * (100 * 300 / 1000)
3 * 30 = 90
This can be easily fixed by reversing the order of the multiplication
and division. After this fix we get:
(MSEC_PER_SEC * (100 * HZ / 1000)) / HZ
(1000 * (100 * 300 / 1000)) / 300
(1000 * 30) / 300 = 100
Fixes: 975e155ed873 ("sched/rt: Show the 'sched_rr_timeslice' SCHED_RR timeslice tuning knob in milliseconds") Signed-off-by: Cyril Hrubis <chrubis@suse.cz> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Reviewed-by: Petr Vorel <pvorel@suse.cz> Acked-by: Mel Gorman <mgorman@suse.de> Tested-by: Petr Vorel <pvorel@suse.cz> Link: https://lore.kernel.org/r/20230802151906.25258-2-chrubis@suse.cz
[ pvorel: rebased for 5.15, 5.10 ] Signed-off-by: Petr Vorel <pvorel@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Write error handling is racy and can sometime lead to the error recovery
path wrongly changing the inode size of a sequential zone file to an
incorrect value which results in garbage data being readable at the end
of a file. There are 2 problems:
1) zonefs_file_dio_write() updates a zone file write pointer offset
after issuing a direct IO with iomap_dio_rw(). This update is done
only if the IO succeed for synchronous direct writes. However, for
asynchronous direct writes, the update is done without waiting for
the IO completion so that the next asynchronous IO can be
immediately issued. However, if an asynchronous IO completes with a
failure right before the i_truncate_mutex lock protecting the update,
the update may change the value of the inode write pointer offset
that was corrected by the error path (zonefs_io_error() function).
2) zonefs_io_error() is called when a read or write error occurs. This
function executes a report zone operation using the callback function
zonefs_io_error_cb(), which does all the error recovery handling
based on the current zone condition, write pointer position and
according to the mount options being used. However, depending on the
zoned device being used, a report zone callback may be executed in a
context that is different from the context of __zonefs_io_error(). As
a result, zonefs_io_error_cb() may be executed without the inode
truncate mutex lock held, which can lead to invalid error processing.
Fix both problems as follows:
- Problem 1: Perform the inode write pointer offset update before a
direct write is issued with iomap_dio_rw(). This is safe to do as
partial direct writes are not supported (IOMAP_DIO_PARTIAL is not
set) and any failed IO will trigger the execution of zonefs_io_error()
which will correct the inode write pointer offset to reflect the
current state of the one on the device.
- Problem 2: Change zonefs_io_error_cb() into zonefs_handle_io_error()
and call this function directly from __zonefs_io_error() after
obtaining the zone information using blkdev_report_zones() with a
simple callback function that copies to a local stack variable the
struct blk_zone obtained from the device. This ensures that error
handling is performed holding the inode truncate mutex.
This change also simplifies error handling for conventional zone files
by bypassing the execution of report zones entirely. This is safe to
do because the condition of conventional zones cannot be read-only or
offline and conventional zone files are always fully mapped with a
constant file size.
Reported-by: Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com> Fixes: 8dcc1a9d90c1 ("fs: New zonefs file system") Cc: stable@vger.kernel.org Signed-off-by: Damien Le Moal <dlemoal@kernel.org> Tested-by: Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com> Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com> Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In mfill_atomic_hugetlb(), mmap_changing isn't being checked
again if we drop mmap_lock and reacquire it. When the lock is not held,
mmap_changing could have been incremented. This is also inconsistent
with the behavior in mfill_atomic().
Link: https://lkml.kernel.org/r/20240117223729.1444522-1-lokeshgidra@google.com Fixes: df2cc96e77011 ("userfaultfd: prevent non-cooperative events vs mcopy_atomic races") Signed-off-by: Lokesh Gidra <lokeshgidra@google.com> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Mike Rapoport <rppt@kernel.org> Cc: Axel Rasmussen <axelrasmussen@google.com> Cc: Brian Geffon <bgeffon@google.com> Cc: David Hildenbrand <david@redhat.com> Cc: Jann Horn <jannh@google.com> Cc: Kalesh Singh <kaleshsingh@google.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Nicolas Geoffray <ngeoffray@google.com> Cc: Peter Xu <peterx@redhat.com> Cc: Suren Baghdasaryan <surenb@google.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Mike Rapoport (IBM) <rppt@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The sched_rr_timeslice can be reset to default by writing value that is
<= 0. However after reading from this file we always got the last value
written, which is not useful at all.
The data offset for the SMB3.1.1 POSIX create context will always be
8-byte aligned so having the check 'noff + nlen >= doff' in
smb2_parse_contexts() is wrong as it will lead to -EINVAL because noff
+ nlen == doff.
Fix the sanity check to correctly handle aligned create context data.
Fixes: af1689a9b770 ("smb: client: fix potential OOBs in smb2_parse_contexts()") Signed-off-by: Paulo Alcantara <pc@manguebit.com> Signed-off-by: Steve French <stfrench@microsoft.com>
[Guru:smb2_parse_contexts() is present in file smb2ops.c,
smb2ops.c file location is changed, modified patch accordingly.] Signed-off-by: Guruswamy Basavaiah <guruswamy.basavaiah@broadcom.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reported-by: Robert Morris <rtm@csail.mit.edu> Cc: stable@vger.kernel.org Signed-off-by: Paulo Alcantara (SUSE) <pc@manguebit.com> Signed-off-by: Steve French <stfrench@microsoft.com>
[Guru: Removed changes to cached_dir.c and checking return value
of smb2_parse_contexts in smb2ops.c] Signed-off-by: Guruswamy Basavaiah <guruswamy.basavaiah@broadcom.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The dsmark qdisc has served us well over the years for diffserv but has not
been getting much attention due to other more popular approaches to do diffserv
services. Most recently it has become a shooting target for syzkaller. For this
reason, we are retiring it.
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com> Acked-by: Jiri Pirko <jiri@nvidia.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ATM qdisc has served us well over the years but has not been getting much
TLC due to lack of known users. Most recently it has become a shooting target
for syzkaller. For this reason, we are retiring it.
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com> Acked-by: Jiri Pirko <jiri@nvidia.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While this amazing qdisc has served us well over the years it has not been
getting any tender love and care and has bitrotted over time.
It has become mostly a shooting target for syzkaller lately.
For this reason, we are retiring it. Goodbye CBQ - we loved you.
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com> Acked-by: Jiri Pirko <jiri@nvidia.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The problem is in nft_byteorder_eval() where we are iterating through a
loop and writing to dst[0], dst[1], dst[2] and so on... On each
iteration we are writing 8 bytes. But dst[] is an array of u32 so each
element only has space for 4 bytes. That means that every iteration
overwrites part of the previous element.
I spotted this bug while reviewing commit caf3ef7468f7 ("netfilter:
nf_tables: prevent OOB access in nft_byteorder_eval") which is a related
issue. I think that the reason we have not detected this bug in testing
is that most of time we only write one element.
Fixes: ce1e7989d989 ("netfilter: nft_byteorder: provide 64bit le/be conversion") Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
[Ajay: Modified to apply on v5.10.y] Signed-off-by: Ajay Kaher <ajay.kaher@broadcom.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Drivers in ->remove() callback should undo the runtime PM changes done
in ->probe(). Usually this means calling pm_runtime_disable(),
pm_runtime_dont_use_autosuspend() etc.
>From grepping code, it's clear that many people aren't aware of the
need to call pm_runtime_dont_use_autosuspend().
When brainstorming solutions, one idea that came up was to leverage
the new-ish devm_pm_runtime_enable() function. The idea here is that:
* When the devm action is called we know that the driver is being
removed. It's the perfect time to undo the use_autosuspend.
* The code of pm_runtime_dont_use_autosuspend() already handles the
case of being called when autosuspend wasn't enabled.
Suggested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Douglas Anderson <dianders@chromium.org> Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Stable-dep-of: 3d07a411b4fa ("drm/msm/dsi: Use pm_runtime_resume_and_get to prevent refcnt leaks") Signed-off-by: Amit Pundir <amit.pundir@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A typical code pattern for pm_runtime_enable() call is to call it in the
_probe function and to call pm_runtime_disable() both from _probe error
path and from _remove function. For some drivers the whole remove
function would consist of the call to pm_remove_disable().
Add helper function to replace this bolierplate piece of code. Calling
devm_pm_runtime_enable() removes the need for calling
pm_runtime_disable() both in the probe()'s error path and in the
remove() function.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Link: https://lore.kernel.org/r/20210731195034.979084-2-dmitry.baryshkov@linaro.org Acked-by: Rafael J. Wysocki <rafael@kernel.org> Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Stable-dep-of: 3d07a411b4fa ("drm/msm/dsi: Use pm_runtime_resume_and_get to prevent refcnt leaks") Signed-off-by: Amit Pundir <amit.pundir@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If DAT metadata file block access fails due to corruption of the DAT file
or abnormal virtual block numbers held by b-trees or inodes, a kernel
warning is generated.
This replaces the WARN_ONs by error output, so that a kernel, booted with
panic_on_warn, does not panic. This patch also replaces the detected
return code -ENOENT with another internal code -EINVAL to notify the bmap
layer of metadata corruption. When the bmap layer sees -EINVAL, it
handles the abnormal situation with nilfs_bmap_convert_error() and finally
returns code -EIO as it should.
According to a syzbot report, end_buffer_async_write(), which handles the
completion of block device writes, may detect abnormal condition of the
buffer async_write flag and cause a BUG_ON failure when using nilfs2.
Nilfs2 itself does not use end_buffer_async_write(). But, the async_write
flag is now used as a marker by commit 7f42ec394156 ("nilfs2: fix issue
with race condition of competition between segments for dirty blocks") as
a means of resolving double list insertion of dirty blocks in
nilfs_lookup_dirty_data_buffers() and nilfs_lookup_node_buffers() and the
resulting crash.
This modification is safe as long as it is used for file data and b-tree
node blocks where the page caches are independent. However, it was
irrelevant and redundant to also introduce async_write for segment summary
and super root blocks that share buffers with the backing device. This
led to the possibility that the BUG_ON check in end_buffer_async_write
would fail as described above, if independent writebacks of the backing
device occurred in parallel.
The use of async_write for segment summary buffers has already been
removed in a previous change.
Fix this issue by removing the manipulation of the async_write flag for
the remaining super root block buffer.
Link: https://lkml.kernel.org/r/20240203161645.4992-1-konishi.ryusuke@gmail.com Fixes: 7f42ec394156 ("nilfs2: fix issue with race condition of competition between segments for dirty blocks") Signed-off-by: Ryusuke Konishi <konishi.ryusuke@gmail.com> Reported-by: syzbot+5c04210f7c7f897c1e7f@syzkaller.appspotmail.com Closes: https://lkml.kernel.org/r/00000000000019a97c05fd42f8c8@google.com Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On some systems, sys_membarrier can be very expensive, causing overall
slowdowns for everything. So put a lock on the path in order to
serialize the accesses to prevent the ability for this to be called at
too high of a frequency and saturate the machine.
Reviewed-and-tested-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com> Acked-by: Borislav Petkov <bp@alien8.de> Fixes: 22e4ebb97582 ("membarrier: Provide expedited private command") Fixes: c5f58bd58f43 ("membarrier: Provide GLOBAL_EXPEDITED command") Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
[ converted to explicit mutex_*() calls - cleanup.h is not in this stable
branch - gregkh ] Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The shadow call stack for irq now is stored in current task's thread info
in irq_stack_entry. There is a possibility that we have some soft irqs
pending at the end of hard irq, and when we process softirq with the irq
enabled, irq_stack_entry will enter again and overwrite the shadow call
stack whitch stored in current task's thread info, leading to the
incorrect shadow call stack restoration for the first entry of the hard
IRQ, then the system end up with a panic.
While in theory the timer can be triggered before expires + delta, for the
cases of RT tasks they really have no business giving any lenience for
extra slack time, so override any passed value by the user and always use
zero for schedule_hrtimeout_range() calls. Furthermore, this is similar to
what the nanosleep(2) family already does with current->timer_slack_ns.
Signed-off-by: Davidlohr Bueso <dave@stgolabs.net> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Link: https://lore.kernel.org/r/20230123173206.6764-3-dave@stgolabs.net Signed-off-by: Felix Moessbauer <felix.moessbauer@siemens.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The patch fdb8e12cc2cc ("netfilter: ipset: fix performance regression
in swap operation") missed to add the calls to gc cancellations
at the error path of create operations and at module unload. Also,
because the half of the destroy operations now executed by a
function registered by call_rcu(), neither NFNL_SUBSYS_IPSET mutex
or rcu read lock is held and therefore the checking of them results
false warnings.
The patch "netfilter: ipset: fix race condition between swap/destroy
and kernel side add/del/test", commit 28628fa9 fixes a race condition.
But the synchronize_rcu() added to the swap function unnecessarily slows
it down: it can safely be moved to destroy and use call_rcu() instead.
Eric Dumazet pointed out that simply calling the destroy functions as
rcu callback does not work: sets with timeout use garbage collectors
which need cancelling at destroy which can wait. Therefore the destroy
functions are split into two: cancelling garbage collectors safely at
executing the command received by netlink and moving the remaining
part only into the rcu callback.
Link: https://lore.kernel.org/lkml/C0829B10-EAA6-4809-874E-E1E9C05A8D84@automattic.com/ Fixes: 28628fa952fe ("netfilter: ipset: fix race condition between swap/destroy and kernel side add/del/test") Reported-by: Ale Crismani <ale.crismani@automattic.com> Reported-by: David Wang <00107082@163.com> Tested-by: David Wang <00107082@163.com> Signed-off-by: Jozsef Kadlecsik <kadlec@netfilter.org> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
GNU's addr2line can have problems parsing a vmlinux built with LLVM,
particularly when LTO was used. In order to decode the traces correctly
this patch adds the ability to switch to LLVM's utilities readelf and
addr2line. The same approach is followed by Will in [1].
Note that one could set CROSS_COMPILE=llvm- instead to hack around this
issue. However, doing so can break the decodecode routine as it will
force the selection of other LLVM utilities down the line e.g. llvm-as.
Sometimes if you're using tools that have linked things improperly or have
new features/sections that older tools don't expect you'll see warnings
printed to stderr. We don't really care about these warnings, so let's
just silence these messages to cleanup output of this script.
Link: https://lkml.kernel.org/r/20210511003845.2429846-10-swboyd@chromium.org Signed-off-by: Stephen Boyd <swboyd@chromium.org> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Alexei Starovoitov <ast@kernel.org> Cc: Jessica Yu <jeyu@kernel.org> Cc: Evan Green <evgreen@chromium.org> Cc: Hsin-Yi Wang <hsinyi@chromium.org> Cc: Konstantin Khlebnikov <khlebnikov@yandex-team.ru> Cc: Sasha Levin <sashal@kernel.org> Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Cc: Baoquan He <bhe@redhat.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Dave Young <dyoung@redhat.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Petr Mladek <pmladek@suse.com> Cc: Rasmus Villemoes <linux@rasmusvillemoes.dk> Cc: Sergey Senozhatsky <sergey.senozhatsky@gmail.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Vivek Goyal <vgoyal@redhat.com> Cc: Will Deacon <will@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Stable-dep-of: efbd63983533 ("scripts/decode_stacktrace.sh: optionally use LLVM utilities") Signed-off-by: Sasha Levin <sashal@kernel.org>
The UART supports an auto-RTS mode in which the RTS pin is automatically
activated during transmission. So mark this mode as being supported even
if RTS is not controlled by the driver but the UART.
Also the serial core expects now at least one of both modes rts-on-send or
rts-after-send to be supported. This is since during sanitization
unsupported flags are deleted from a RS485 configuration set by userspace.
However if the configuration ends up with both flags unset, the core prints
a warning since it considers such a configuration invalid (see
uart_sanitize_serial_rs485()).
Preparing to move serial_rs485 struct sanitization into serial core,
each driver has to provide what fields/flags it supports. This
information is pointed into by rs485_supported.
When the mpi_ec_ctx structure is initialized, some fields are not
cleared, causing a crash when referencing the field when the
structure was released. Initially, this issue was ignored because
memory for mpi_ec_ctx is allocated with the __GFP_ZERO flag.
For example, this error will be triggered when calculating the
Za value for SM2 separately.
max_mapnr variable is utilized in the pfn_valid() method in order to
determine the upper PFN space boundary. Having it uninitialized
effectively makes any PFN passed to that method invalid. That in its turn
causes the kernel mm-subsystem occasion malfunctions even after the
max_mapnr variable is actually properly updated. For instance,
pfn_valid() is called in the init_unavailable_range() method in the
framework of the calls-chain on MIPS:
setup_arch()
+-> paging_init()
+-> free_area_init()
+-> memmap_init()
+-> memmap_init_zone_range()
+-> init_unavailable_range()
Since pfn_valid() always returns "false" value before max_mapnr is
initialized in the mem_init() method, any flatmem page-holes will be left
in the poisoned/uninitialized state including the IO-memory pages. Thus
any further attempts to map/remap the IO-memory by using MMU may fail.
In particular it happened in my case on attempt to map the SRAM region.
The kernel bootup procedure just crashed on the unhandled unaligned access
bug raised in the __update_cache() method:
Let's fix the problem by initializing the max_mapnr variable as soon as
the required data is available. In particular it can be done right in the
paging_init() method before free_area_init() is called since all the PFN
zone boundaries have already been calculated by that time.
Commit 6f5e193bfb55 ("PCI: dwc: Fix dw_pcie_ep_raise_msix_irq() to get
correct MSI-X table address") modified dw_pcie_ep_raise_msix_irq() to
support iATUs which require a specific alignment.
However, this support cannot have been properly tested.
The whole point is for the iATU to map an address that is aligned,
using dw_pcie_ep_map_addr(), and then let the writel() write to
ep->msi_mem + aligned_offset.
Thus, modify the address that is mapped such that it is aligned.
With this change, dw_pcie_ep_raise_msix_irq() matches the logic in
dw_pcie_ep_raise_msi_irq().
Link: https://lore.kernel.org/linux-pci/20231128132231.2221614-1-nks@flawful.org Fixes: 6f5e193bfb55 ("PCI: dwc: Fix dw_pcie_ep_raise_msix_irq() to get correct MSI-X table address") Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com> Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org> Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Cc: stable@vger.kernel.org # 5.7 Cc: Kishon Vijay Abraham I <kishon@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
That commit introduced the following race and can cause system hung.
md_write_start: raid5d:
// mddev->in_sync == 1
set "MD_SB_CHANGE_PENDING"
// running before md_write_start wakeup it
waiting "MD_SB_CHANGE_PENDING" cleared
>>>>>>>>> hung
wakeup mddev->thread
...
waiting "MD_SB_CHANGE_PENDING" cleared
>>>> hung, raid5d should clear this flag
but get hung by same flag.
The issue reverted commit fixing is fixed by last patch in a new way.
Fixes: 5e2cf333b7bd ("md/raid5: Wait for MD_SB_CHANGE_PENDING in raid5d") Cc: stable@vger.kernel.org # v5.19+ Signed-off-by: Junxiao Bi <junxiao.bi@oracle.com> Reviewed-by: Yu Kuai <yukuai3@huawei.com> Signed-off-by: Song Liu <song@kernel.org> Link: https://lore.kernel.org/r/20231108182216.73611-2-junxiao.bi@oracle.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Where that s->saved_cmdlines allocation looks to be a dangling allocation
to kmemleak. That's because kmemleak only keeps track of kmalloc()
allocations. For allocations that use page_alloc() directly, the kmemleak
needs to be explicitly informed about it.
Add kmemleak_alloc() and kmemleak_free() around the page allocation so
that it doesn't give the following false positive:
The unused clock cleanup uses the _sync initcall to give all users at
earlier initcalls time to probe. Do the same to avoid leaving some PDs
dangling at "on" (which actually happened on qcom!).
Lock jsk->sk to prevent UAF when setsockopt(..., SO_J1939_FILTER, ...)
modifies jsk->filters while receiving packets.
Following trace was seen on affected system:
==================================================================
BUG: KASAN: slab-use-after-free in j1939_sk_recv_match_one+0x1af/0x2d0 [can_j1939]
Read of size 4 at addr ffff888012144014 by task j1939/350
In fs/ceph/caps.c, in encode_cap_msg(), "use after free" error was
caught by KASAN at this line - 'ceph_buffer_get(arg->xattr_buf);'. This
implies before the refcount could be increment here, it was freed.
In same file, in "handle_cap_grant()" refcount is decremented by this
line - 'ceph_buffer_put(ci->i_xattrs.blob);'. It appears that a race
occurred and resource was freed by the latter line before the former
line could increment it.
encode_cap_msg() is called by __send_cap() and __send_cap() is called by
ceph_check_caps() after calling __prep_cap(). __prep_cap() is where
arg->xattr_buf is assigned to ci->i_xattrs.blob. This is the spot where
the refcount must be increased to prevent "use after free" error.
Cc: stable@vger.kernel.org Link: https://tracker.ceph.com/issues/59259 Signed-off-by: Rishabh Dave <ridave@redhat.com> Reviewed-by: Jeff Layton <jlayton@kernel.org> Reviewed-by: Xiubo Li <xiubli@redhat.com> Signed-off-by: Ilya Dryomov <idryomov@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Symptom:
In case of a bad cable connection (e.g. dirty optics) a fast sequence of
network DOWN-UP-DOWN-UP could happen. UP triggers recovery of the qeth
interface. In case of a second DOWN while recovery is still ongoing, it
can happen that the IP@ of a Layer3 qeth interface is lost and will not
be recovered by the second UP.
Problem:
When registration of IP addresses with Layer 3 qeth devices fails, (e.g.
because of bad address format) the respective IP address is deleted from
its hash-table in the driver. If registration fails because of a ENETDOWN
condition, the address should stay in the hashtable, so a subsequent
recovery can restore it.
3caa4af834df ("qeth: keep ip-address after LAN_OFFLINE failure")
fixes this for registration failures during normal operation, but not
during recovery.
Solution:
Keep L3-IP address in case of ENETDOWN in qeth_l3_recover_ip(). For
consistency with qeth_l3_add_ip() we also keep it in case of EADDRINUSE,
i.e. for some reason the card already/still has this address registered.
Fixes: 4a71df50047f ("qeth: new qeth device driver") Cc: stable@vger.kernel.org Signed-off-by: Alexandra Winter <wintera@linux.ibm.com> Link: https://lore.kernel.org/r/20240206085849.2902775-1-wintera@linux.ibm.com Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When updating the affinity of a VPE, the VMOVP command is currently skipped
if the two CPUs are part of the same VPE affinity.
But this is wrong, as the doorbell corresponding to this VPE is still
delivered on the 'old' CPU, which screws up the balancing. Furthermore,
offlining that 'old' CPU results in doorbell interrupts generated for this
VPE being discarded.
The harsh reality is that VMOVP cannot be elided when a set_affinity()
request occurs. It needs to be obeyed, and if an optimisation is to be
made, it is at the point where the affinity change request is made (such as
in KVM).
Drop the VMOVP elision altogether, and only use the vpe_table_mask
to try and stay within the same ITS affinity group if at all possible.
Fixes: dd3f050a216e (irqchip/gic-v4.1: Implement the v4.1 flavour of VMOVP) Reported-by: Kunkun Jiang <jiangkunkun@huawei.com> Signed-off-by: Marc Zyngier <maz@kernel.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20240213101206.2137483-4-maz@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It was observed on Broadcom devices that use GIC v3 architecture L1
interrupt controllers as the parent of brcmstb-l2 interrupt controllers
that the deactivation of the parent interrupt could happen before the
brcmstb-l2 deasserted its output. This would lead the GIC to reactivate the
interrupt only to find that no L2 interrupt was pending. The result was a
spurious interrupt invoking handle_bad_irq() with its associated
messaging. While this did not create a functional problem it is a waste of
cycles.
The hazard exists because the memory mapped bus writes to the brcmstb-l2
registers are buffered and the GIC v3 architecture uses a very efficient
system register write to deactivate the interrupt.
Add a write memory barrier prior to invoking chained_irq_exit() to
introduce a dsb(st) on those systems to ensure the system register write
cannot be executed until the memory mapped writes are visible to the
system.
[ florian: Added Fixes tag ]
Fixes: 7f646e92766e ("irqchip: brcmstb-l2: Add Broadcom Set Top Box Level-2 interrupt controller") Signed-off-by: Doug Berger <opendmb@gmail.com> Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Florian Fainelli <florian.fainelli@broadcom.com> Acked-by: Marc Zyngier <maz@kernel.org> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20240210012449.3009125-1-florian.fainelli@broadcom.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This pointer can change here since the SKB can change, so we
actually later open-coded IEEE80211_SKB_CB() again. Reload
the pointer where needed, so the monitor-mode case using it
gets fixed, and then use info-> later as well.
When physical ports are reset (either through link failure or manually
toggled down and up again) that are slaved to a Linux bond with a tunnel
endpoint IP address on the bond device, not all tunnel packets arriving
on the bond port are decapped as expected.
The bond dev assigns the same MAC address to itself and each of its
slaves. When toggling a slave device, the same MAC address is therefore
offloaded to the NFP multiple times with different indexes.
The issue only occurs when re-adding the shared mac. The
nfp_tunnel_add_shared_mac() function has a conditional check early on
that checks if a mac entry already exists and if that mac entry is
global: (entry && nfp_tunnel_is_mac_idx_global(entry->index)). In the
case of a bonded device (For example br-ex), the mac index is obtained,
and no new index is assigned.
We therefore modify the conditional in nfp_tunnel_add_shared_mac() to
check if the port belongs to the LAG along with the existing checks to
prevent a new global mac index from being re-assigned to the slave port.
Fixes: 20cce8865098 ("nfp: flower: enable MAC address sharing for offloadable devs") CC: stable@vger.kernel.org # 5.1+ Signed-off-by: Daniel de Villiers <daniel.devilliers@corigine.com> Signed-off-by: Louis Peens <louis.peens@corigine.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 1st and 2nd expansion BAR configuration registers are configured,
when the driver starts up, in variables 'barcfg_msix_general' and
'barcfg_msix_xpb', respectively. The 'LengthSelect' field is ORed in
from bit 0, which is incorrect. The 'LengthSelect' field should
start from bit 27.
This has largely gone un-noticed because
NFP_PCIE_BAR_PCIE2CPP_LengthSelect_32BIT happens to be 0.
Fixes: 4cb584e0ee7d ("nfp: add CPP access core") Cc: stable@vger.kernel.org # 4.11+ Signed-off-by: Daniel Basilio <daniel.basilio@corigine.com> Signed-off-by: Louis Peens <louis.peens@corigine.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes: 1b05ece0c931 ("crypto: ccp - During shutdown, check SEV data pointer before using") Cc: stable@vger.kernel.org Reviewed-by: Mario Limonciello <mario.limonciello@amd.com> Signed-off-by: Kim Phillips <kim.phillips@amd.com> Reviewed-by: Liam Merwick <liam.merwick@oracle.com> Acked-by: John Allen <john.allen@amd.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Syzbot reported a hang issue in migrate_pages_batch() called by mbind()
and nilfs_lookup_dirty_data_buffers() called in the log writer of nilfs2.
While migrate_pages_batch() locks a folio and waits for the writeback to
complete, the log writer thread that should bring the writeback to
completion picks up the folio being written back in
nilfs_lookup_dirty_data_buffers() that it calls for subsequent log
creation and was trying to lock the folio. Thus causing a deadlock.
In the first place, it is unexpected that folios/pages in the middle of
writeback will be updated and become dirty. Nilfs2 adds a checksum to
verify the validity of the log being written and uses it for recovery at
mount, so data changes during writeback are suppressed. Since this is
broken, an unclean shutdown could potentially cause recovery to fail.
Investigation revealed that the root cause is that the wait for writeback
completion in nilfs_page_mkwrite() is conditional, and if the backing
device does not require stable writes, data may be modified without
waiting.
Fix these issues by making nilfs_page_mkwrite() wait for writeback to
finish regardless of the stable write requirement of the backing device.
Link: https://lkml.kernel.org/r/20240131145657.4209-1-konishi.ryusuke@gmail.com Fixes: 1d1d1a767206 ("mm: only enforce stable page writes if the backing device requires it") Signed-off-by: Ryusuke Konishi <konishi.ryusuke@gmail.com> Reported-by: syzbot+ee2ae68da3b22d04cd8d@syzkaller.appspotmail.com Closes: https://lkml.kernel.org/r/00000000000047d819061004ad6c@google.com Tested-by: Ryusuke Konishi <konishi.ryusuke@gmail.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The helper function nilfs_recovery_copy_block() of
nilfs_recovery_dsync_blocks(), which recovers data from logs created by
data sync writes during a mount after an unclean shutdown, incorrectly
calculates the on-page offset when copying repair data to the file's page
cache. In environments where the block size is smaller than the page
size, this flaw can cause data corruption and leak uninitialized memory
bytes during the recovery process.
Fix these issues by correcting this byte offset calculation on the page.
This change uses the appropriate _cansleep or non-sleeping API for
reading GPIO read-only state. This allows users with GPIOs that
never sleepbeing called in atomic context.
Implement the same mechanism as in commit 52af318c93e97 ("mmc: Allow
non-sleeping GPIO cd").
When ident_pud_init() uses only gbpages to create identity maps, large
ranges of addresses not actually requested can be included in the
resulting table; a 4K request will map a full GB. On UV systems, this
ends up including regions that will cause hardware to halt the system
if accessed (these are marked "reserved" by BIOS). Even processor
speculation into these regions is enough to trigger the system halt.
Only use gbpages when map creation requests include the full GB page
of space. Fall back to using smaller 2M pages when only portions of a
GB page are included in the request.
No attempt is made to coalesce mapping requests. If a request requires
a map entry at the 2M (pmd) level, subsequent mapping requests within
the same 1G region will also be at the pmd level, even if adjacent or
overlapping such requests could have been combined to map a full
gbpage. Existing usage starts with larger regions and then adds
smaller regions, so this should not have any great consequence.
[ dhansen: fix up comment formatting, simplifty changelog ]
The kernel built with MCRUSOE is unbootable on Transmeta Crusoe. It shows
the following error message:
This kernel requires an i686 CPU, but only detected an i586 CPU.
Unable to boot - please use a kernel appropriate for your CPU.
Remove MCRUSOE from the condition introduced in commit in Fixes, effectively
changing X86_MINIMUM_CPU_FAMILY back to 5 on that machine, which matches the
CPU family given by CPUID.
[ bp: Massage commit message. ]
Fixes: 25d76ac88821 ("x86/Kconfig: Explicitly enumerate i686-class CPUs in Kconfig") Signed-off-by: Aleksander Mazur <deweloper@wp.pl> Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de> Acked-by: H. Peter Anvin <hpa@zytor.com> Cc: <stable@kernel.org> Link: https://lore.kernel.org/r/20240123134309.1117782-1-deweloper@wp.pl Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some people are seeing a warning similar to this when using a crystal:
max310x 11-006c: clock is not stable yet
The datasheet doesn't mention the maximum time to wait for the clock to be
stable when using a crystal, and it seems that the 10ms delay in the driver
is not always sufficient.
Jan Kundrát reported that it took three tries (each separated by 10ms) to
get a stable clock.
Modify behavior to check stable clock ready bit multiple times (20), and
waiting 10ms between each try.
Note: the first draft of the driver originally used a 50ms delay, without
checking the clock stable bit.
Then a loop with 1000 retries was implemented, each time reading the clock
stable bit.
The return type for ring_buffer_poll_wait() is __poll_t. This is behind
the scenes an unsigned where we can set event bits. In case of a
non-allocated CPU, we do return instead -EINVAL (0xffffffea). Lucky us,
this ends up setting few error bits (EPOLLERR | EPOLLHUP | EPOLLNVAL), so
user-space at least is aware something went wrong.
Nonetheless, this is an incorrect code. Replace that -EINVAL with a
proper EPOLLERR to clean that output. As this doesn't change the
behaviour, there's no need to treat this change as a bug fix.
Link: https://lore.kernel.org/linux-trace-kernel/20240131140955.3322792-1-vdonnefort@google.com Cc: stable@vger.kernel.org Fixes: 6721cb6002262 ("ring-buffer: Do not poll non allocated cpu buffers") Signed-off-by: Vincent Donnefort <vdonnefort@google.com> Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In commit ac5047671758 ("hv_netvsc: Disable NAPI before closing the
VMBus channel"), napi_disable was getting called for all channels,
including all subchannels without confirming if they are enabled or not.
This caused hv_netvsc getting hung at napi_disable, when netvsc_probe()
has finished running but nvdev->subchan_work has not started yet.
netvsc_subchan_work() -> rndis_set_subchannel() has not created the
sub-channels and because of that netvsc_sc_open() is not running.
netvsc_remove() calls cancel_work_sync(&nvdev->subchan_work), for which
netvsc_subchan_work did not run.
netif_napi_add() sets the bit NAPI_STATE_SCHED because it ensures NAPI
cannot be scheduled. Then netvsc_sc_open() -> napi_enable will clear the
NAPIF_STATE_SCHED bit, so it can be scheduled. napi_disable() does the
opposite.
Now during netvsc_device_remove(), when napi_disable is called for those
subchannels, napi_disable gets stuck on infinite msleep.
This fix addresses this problem by ensuring that napi_disable() is not
getting called for non-enabled NAPI struct.
But netif_napi_del() is still necessary for these non-enabled NAPI struct
for cleanup purpose.
The kernel fails when compiling without `CONFIG_REGMAP_I2C` but with
`CONFIG_BMA400`.
```
ld: drivers/iio/accel/bma400_i2c.o: in function `bma400_i2c_probe':
bma400_i2c.c:(.text+0x23): undefined reference to `__devm_regmap_init_i2c'
```
Recently, we encounter kernel crash in function rm3100_common_probe
caused by out of bound access of array rm3100_samp_rates (because of
underlying hardware failures). Add boundary check to prevent out of
bound access.
Fixes: 121354b2eceb ("iio: magnetometer: Add driver support for PNI RM3100") Suggested-by: Zhouyi Zhou <zhouzhouyi@gmail.com> Signed-off-by: zhili.liu <zhili.liu@ucas.com.cn> Link: https://lore.kernel.org/r/1704157631-3814-1-git-send-email-zhouzhouyi@gmail.com Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 4c3577db3e4f ("Staging: iio: impedance-analyzer: Fix sparse
warning") fixed a compiler warning, but introduced a bug that resulted
in one of the two 16 bit IIO channels always being zero (when both are
enabled).
This is because int is 32 bits wide on most architectures and in the
case of a little-endian machine the two most significant bytes would
occupy the buffer for the second channel as 'val' is being passed as a
void pointer to 'iio_push_to_buffers()'.
Fix by defining 'val' as u16. Tested working on ARM64.
While looking at improving the saved_cmdlines cache I found a huge amount
of wasted memory that should be used for the cmdlines.
The tracing data saves pids during the trace. At sched switch, if a trace
occurred, it will save the comm of the task that did the trace. This is
saved in a "cache" that maps pids to comms and exposed to user space via
the /sys/kernel/tracing/saved_cmdlines file. Currently it only caches by
default 128 comms.
The structure that uses this creates an array to store the pids using
PID_MAX_DEFAULT (which is usually set to 32768). This causes the structure
to be of the size of 131104 bytes on 64 bit machines.
In hex: 131104 = 0x20020, and since the kernel allocates generic memory in
powers of two, the kernel would allocate 0x40000 or 262144 bytes to store
this structure. That leaves 131040 bytes of wasted space.
Worse, the structure points to an allocated array to store the comm names,
which is 16 bytes times the amount of names to save (currently 128), which
is 2048 bytes. Instead of allocating a separate array, make the structure
end with a variable length string and use the extra space for that.
This is similar to a recommendation that Linus had made about eventfs_inode names:
Instead of allocating a separate string array to hold the saved comms,
have the structure end with: char saved_cmdlines[]; and round up to the
next power of two over sizeof(struct saved_cmdline_buffers) + num_cmdlines * TASK_COMM_LEN
It will use this extra space for the saved_cmdline portion.
Now, instead of saving only 128 comms by default, by using this wasted
space at the end of the structure it can save over 8000 comms and even
saves space by removing the need for allocating the other array.
Link: https://lore.kernel.org/linux-trace-kernel/20240209063622.1f7b6d5f@rorschach.local.home Cc: stable@vger.kernel.org Cc: Masami Hiramatsu <mhiramat@kernel.org> Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com> Cc: Vincent Donnefort <vdonnefort@google.com> Cc: Sven Schnelle <svens@linux.ibm.com> Cc: Mete Durlu <meted@linux.ibm.com> Fixes: 939c7a4f04fcd ("tracing: Introduce saved_cmdlines_size file") Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In ext4_move_extents(), moved_len is only updated when all moves are
successfully executed, and only discards orig_inode and donor_inode
preallocations when moved_len is not zero. When the loop fails to exit
after successfully moving some extents, moved_len is not updated and
remains at 0, so it does not discard the preallocations.
If the moved extents overlap with the preallocated extents, the
overlapped extents are freed twice in ext4_mb_release_inode_pa() and
ext4_process_freed_data() (as described in commit 94d7c16cbbbd ("ext4:
Fix double-free of blocks with EXT4_IOC_MOVE_EXT")), and bb_free is
incremented twice. Hence when trim is executed, a zero-division bug is
triggered in mb_update_avg_fragment_size() because bb_free is not zero
and bb_fragments is zero.
Therefore, update move_len after each extent move to avoid the issue.
Reported-by: Wei Chen <harperchen1110@gmail.com> Reported-by: xingwei lee <xrivendell7@gmail.com> Closes: https://lore.kernel.org/r/CAO4mrferzqBUnCag8R3m2zf897ts9UEuhjFQGPtODT92rYyR2Q@mail.gmail.com Fixes: fcf6b1b729bc ("ext4: refactor ext4_move_extents code base") CC: <stable@vger.kernel.org> # 3.18 Signed-off-by: Baokun Li <libaokun1@huawei.com> Reviewed-by: Jan Kara <jack@suse.cz> Link: https://lore.kernel.org/r/20240104142040.2835097-2-libaokun1@huawei.com Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In remoteproc shutdown sequence, rpmsg_remove will get called which
would depopulate all the child nodes that have been created during
rpmsg_probe. This would result in cb_remove call for all the context
banks for the remoteproc. In cb_remove function, session 0 is
getting skipped which is not correct as session 0 will never become
available again. Add changes to mark session 0 also as invalid.
projects / thirdparty / kernel / stable.git / log
