Akshay Bansod [Mon, 11 Aug 2025 16:56:40 +0000 (22:26 +0530)]
iio: st_lsm6dsx: Replace scnprintf() with sysfs_emit()
Update the sysfs interface for sampling frequency and scale attributes.
Replace `scnprintf()` with `sysfs_emit_at()` which is PAGE_SIZE-aware
and recommended for use in sysfs.
Haibo Chen [Tue, 12 Aug 2025 08:04:23 +0000 (16:04 +0800)]
iio: adc: imx93_adc: load calibrated values even calibration failed
ADC calibration might fail because of the noise on reference voltage.
To avoid calibration fail, need to meet the following requirement:
ADC reference voltage Noise < 1.8V * 1/2^ENOB
For the case which the ADC reference voltage on board do not meet
the requirement, still load the calibrated values, so ADC can also
work but maybe not that accurate.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com> Reviewed-by: Frank Li <Frank.Li@nxp.com> Reviewed-by: Primoz Fiser <primoz.fiser@norik.com> Link: https://patch.msgid.link/20250812-adc-v2-2-0260833f13b8@nxp.com Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Haibo Chen [Tue, 12 Aug 2025 08:04:22 +0000 (16:04 +0800)]
iio: adc: imx93_adc: keep one style of the hex values
Use capital letters consistently for hex values.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com> Reviewed-by: Frank Li <Frank.Li@nxp.com> Reviewed-by: Andy Shevchenko <andy@kernel.org> Link: https://patch.msgid.link/20250812-adc-v2-1-0260833f13b8@nxp.com Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Ben Collins [Tue, 12 Aug 2025 11:12:58 +0000 (07:12 -0400)]
iio: iio_format_list() should set stride=1 for IIO_VAL_CHAR
iio_format_list() sets a stride across the val array of 1 for INT
type, and 2 for all others. Add IIO_VAL_CHAR so it also gets a
stride of 1 assuming val is an array of integers with char type
values.
No drivers currently use this, but I found this issue adding an
avail callback for IIO_INFO_THERMOCOUPLE_TYPE for a driver I'm
working on.
Xichao Zhao [Wed, 13 Aug 2025 07:55:56 +0000 (15:55 +0800)]
iio: adc: ti-tsc2046: use us_to_ktime() where appropriate
Given scan_interval_us and time_per_scan_us are both in usecs, it
makes more sense to use us_to_ktime() helper rather than converting
to nanosecs as needed for ns_to_ktime().
Andrew Davis [Wed, 13 Aug 2025 22:58:38 +0000 (17:58 -0500)]
iio: health: afe4404: Do not store dev pointer in device struct
The device *dev is only used in probe(), so no need to store it
in the device local data struct. In all the places in probe()
we did use that, just use a new local variable for the same.
Andrew Davis [Wed, 13 Aug 2025 22:58:35 +0000 (17:58 -0500)]
iio: health: afe4403: Do not store dev pointer in device struct
The device *dev is only used in probe(), so no need to store it
in the device local data struct. In all the places in probe()
we did use that, just use a new local variable for the same.
The ROHM BD79105 is a simple 16-bit ADC accessible via SPI*.
The BD79105 has a CONVSTART pin, which must be set high to start the ADC
conversion. Unlike with the ad7091 and ad7091r which also have a
CONVSTART pin, the BD79105 requires that the pin must remain high also
for the duration of the SPI access.
(*) Couple of words about the SPI. The BD79105 has pins named as
CONVSTART, SCLK, DIN and DOUT. For the curious reader, DIN is not SPI
ISO.
DIN is a signal which can be used as a chip-select. When DIN is pulled
low, the ADC will output the completed measurement via DOUT as SCLK is
clocked. According to the data-sheet, the DIN can also be used for
daisy-chaining multiple ADCs. Furthermore, DOUT can be used also for a
'data-ready' -IRQ. These modes aren't supported by this driver.
Support reading ADC scale and data from the BD79105 using SPI, when DIN
is used as a chip-select.
The ROHM BD79105 is a simple, 16-bit, 1-channel ADC with a 'CONVSTART'
pin used to start the ADC conversion. Other than the 'CONVSTART', there
are 3 supply pins (one used as a reference), analog inputs, ground and
communication pins. It's worth noting that the pin somewhat confusingly
labeled as 'DIN', is a pin which should be used as a chip-select. The IC
does not have any writable registers.
The device is designed so that the output pin can, in addition to
outputting the data, be used as a 'data-ready'-IRQ. There are cases
where the IRQ can't be used (because it is delivered via SPI data-line).
Hence, some systems may use a GPIO for polling the data readiness.
Add a compatible for the bd79105 and add the data-ready GPIO to the
binding.
Matti Vaittinen [Mon, 11 Aug 2025 08:51:50 +0000 (11:51 +0300)]
dt-bindings: iio: adc: ad7476: Drop redundant prop: true
The ad7476 supports a few variants with different power-supplies and
control GPIOs. The binding first unconditionally introduces all the
properties, and later sets them 'true' or 'false' based on the
combatible.
The 'true' seems to be implied by the initial property introduction so
the 'true' -branches in later conditional handling (based on the
compatible) can be omitted.
Matti Vaittinen [Mon, 11 Aug 2025 08:51:39 +0000 (11:51 +0300)]
iio: adc: ad7476: Conditionally call convstart
The ad7476 supports two IC variants which may have a 'convstart' -GPIO
for starting the conversion. Currently the driver calls a function which
tries to access the GPIO for all of the IC variants, whether they
support 'convstart' or not. This is not an error because this function
returns early if GPIO information is not populated.
We can do a tad better by calling this function only for the ICs which
have the 'convstart' by providing a function pointer to the convstart
function from the chip_info structure, and calling this function only
for the ICs which have the function pointer set.
This does also allow to support ICs which require different convstart
handling than the currently supported ICs.
Call convstart function only on the ICs which can support it and allow
IC-specific convstart functions for the ICs which require different
handling.
Matti Vaittinen [Mon, 11 Aug 2025 08:51:28 +0000 (11:51 +0300)]
iio: adc: ad7476: Drop convstart chan_spec
The ad7476 driver defines separate chan_spec structures for operation
with and without convstart GPIO. At quick glance this may seem as if the
driver did provide more than 1 data-channel to users - one for the
regular data, other for the data obtained with the convstart GPIO.
The only difference between the 'convstart' and 'non convstart'
-channels is presence / absence of the BIT(IIO_CHAN_INFO_RAW) in
channel's flags.
We can drop the convstart channel spec, and related convstart macro, by
allocating a mutable per driver instance channel spec and adding the flag
in probe if needed. This will simplify the driver with the cost of added
memory consumption.
Assuming there aren't systems with very many ADCs and very few
resources, this tradeoff seems worth making.
Simplify the driver by dropping the 'convstart' channel spec and
allocating the channel spec for each driver instance.
Matti Vaittinen [Mon, 11 Aug 2025 08:51:17 +0000 (11:51 +0300)]
iio: adc: ad7476: use *_cansleep GPIO APIs
The ad7476 driver supports ADCs which require a GPIO pin to be used to
start conversion. The GPIO line status seems to be always toggled from
a process context, either from the user-initiated "raw-read conversion",
or from a threaded IRQ handler. Furthermore, these ICs are connected via
SPI bus, which is usually implemented in a way that the access to the
device can sleep. The GPIO here is toggled from the same context which
is reading the results over SPI.
Thus it seems very likely these GPIOs are toggled from a context which
can sleep.
Swap the gpiod_set_value() to gpiod_set_value_cansleep() accordinlgy.
Matti Vaittinen [Mon, 11 Aug 2025 08:51:06 +0000 (11:51 +0300)]
iio: adc: ad7476: Use correct channel for bit info
The ad7476 supports ADCs which use separate GPIO for starting the
conversion. For such devices, the driver uses different channel
information if the GPIO is found. The bit information is still always
used from the original (non 'convstart') channels.
This has not been causing problems because the bit information for the
'convstart' -channel and the 'normal' -channel is identical. It,
however, will cause issues if an IC has different characteristics for an
'convstart' -channel and regular channel. Furthermore, this will cause
problems if a device always requires the convstart GPIO and thus only
defines the convstart channel.
Matti Vaittinen [Mon, 11 Aug 2025 08:50:55 +0000 (11:50 +0300)]
iio: adc: ad7476: Use mV for internal reference
The ad7476 supports some ICs with an internal reference voltage. For
those ICs the reference voltage has been hard-coded as micro volts, but
the value which is later used in code needs to be milli volts. This
results the need to divide hard coded voltage by 1000 before using it.
Simplify code by changing the hard-coded voltage to millivolts and by
dropping the division.
Matti Vaittinen [Mon, 11 Aug 2025 08:50:41 +0000 (11:50 +0300)]
iio: adc: ad7476: Simplify scale handling
The ad7476 driver supports variants with different amount of supply
regulators. On some variants there is only VCC, which is used as a
reference voltage. Others have separate VREF regulator, and some rely on
internal VREF. Some have both internal VREF and option to connect
external one.
The ad7476 driver reads the regulator voltage only when the user asks to
get the scale. This means the driver needs to do some dancing while
picking the correct reference regulator (or internal reference), and
store it for the later use.
According to the discussion [1] variable voltage references are rare,
making it hard to justify the added complexity for supporting those.
Drop the support for the variable voltage references and simplify things
by using the managed regulator get and enable interfaces.
Matti Vaittinen [Mon, 11 Aug 2025 08:50:27 +0000 (11:50 +0300)]
iio: adc: ad7476: Simplify chip type detection
The ad7476 driver uses a table of structures for defining the IC variant
specific data. Table is indexed using enum values, which are picked by
SPI ID.
Having the table and an enum adds extra complexity and may encourage
adding IC specific quircks in the code, instead of centralizing the IC
differences in one place, the chip-info.
Simplify this by dropping the table and using individual structures for
the IC specific data, and storing the IC specific structure's address
directly in the SPI ID data. Finally, switch to the
spi_get_device_match_data() and add a check for the return value.
Waqar Hameed [Tue, 5 Aug 2025 09:33:33 +0000 (11:33 +0200)]
iio: Remove error prints for devm_add_action_or_reset()
When `devm_add_action_or_reset()` fails, it is due to a failed memory
allocation and will thus return `-ENOMEM`. `dev_err_probe()` doesn't do
anything when error is `-ENOMEM`. Therefore, remove the useless call to
`dev_err_probe()` when `devm_add_action_or_reset()` fails, and just
return the value instead.
Signed-off-by: Waqar Hameed <waqar.hameed@axis.com> Reviewed-by: Nuno Sá <nuno.sa@analog.com> Reviewed-by: Andy Shevchenko <andy@kernel.org> Link: https://patch.msgid.link/pndectqm7te.a.out@axis.com Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Stefano Manni [Thu, 7 Aug 2025 07:48:49 +0000 (09:48 +0200)]
iio: adc: ad799x: add reference voltage capability to chip_info
If the chip supports an external reference voltage
on REFIN pin then the "vref-supply" regulator may be used.
This commit partially refactors 6b104e7895ab16b9b7f466c5f2ca282b87f661e8
to add the capability of the chip to have an external
voltage reference and then remove the ugly conditional check
on chip id.
Suggested-by: Andy Shevchenko <andriy.shevchenko@intel.com> Signed-off-by: Stefano Manni <stefano.manni@gmail.com> Acked-by: Andy Shevchenko <andriy.shevchenko@intel.com> Reviewed-by: David Lechner <dlechner@baylibre.com> Link: https://patch.msgid.link/20250807074850.130831-2-stefano.manni@gmail.com Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
docs: iio: describe inactivity and free-fall detection on the ADXL345
Describe the inactivity detection additionally using the free-fall
register. Due to the controversial discussions on the mailing list, this
section of the documentation will be committed separately to allow for a
more focused and detailed elaboration of the topic.
iio: accel: adxl345: extend inactivity time for less than 1s
Inactivity and free-fall events are essentially the same type of sensor
events. Therefore, inactivity detection (normally set for periods between 1
and 255 seconds) can be extended for shorter durations to support free-fall
detection.
For periods shorter than 1 second, the driver automatically configures the
threshold and duration using the free-fall register. For periods longer
than 1 second, it uses the inactivity threshold and duration using the
inactivity registers.
When using the free-fall register, the link bit is not set, which means
auto-sleep cannot be enabled if activity detection is also active.
iio: accel: adxl345: add coupling detection for activity/inactivity
Enable AC/DC coupling configuration for activity and inactivity detection
by setting the AC/DC bit. Extend existing magnitude-based detection with
adaptive AC-coupled mode.
Use DC-coupled mode to compare acceleration samples directly against
configured thresholds. Use AC-coupled mode to compare samples against a
reference taken at the start of activity detection. Implement DC-coupled
events using MAG, and AC-coupled events using MAG_ADAPTIVE.
Expose configuration of thresholds and periods via separate sysfs handles.
Note that both coupling modes share the same sensor registers, so activity
or inactivity detection cannot be configured for both AC and DC
simultaneously. Apply the most recently configured mode.
Simplify event handling and support adaptive AC-coupling.
Add support for the sensor’s inactivity feature in the driver. When both
activity and inactivity detection are enabled, the sensor sets a link bit
that ties the two functions together. This also enables auto-sleep mode,
allowing the sensor to automatically enter sleep state upon detecting
inactivity.
Inactivity detection relies on a configurable threshold and a specified
time period. If sensor measurements remain below the threshold for the
defined duration, the sensor transitions to the inactivity state.
When an Output Data Rate (ODR) is set, the inactivity time period is
automatically adjusted to a sensible default. Higher ODRs result in shorter
inactivity timeouts, while lower ODRs allow longer durations-within
reasonable upper and lower bounds. This is important because features like
auto-sleep operate effectively only between 12.5 Hz and 400 Hz. These
defaults are applied when the sample rate is modified, but users can
override them by explicitly setting a custom inactivity timeout.
Similarly, configuring the g-range provides default threshold values for
both activity and inactivity detection. These are implicit defaults meant
to simplify configuration, but they can also be manually overridden as
needed.
Enable the sensor to detect activity and trigger interrupts accordingly.
Activity events are determined based on a threshold, which is initialized
to a sensible default during probe. This default value is adopted from the
legacy ADXL345 input driver to maintain consistent behavior.
The combination of activity detection, ODR configuration, and range
settings lays the groundwork for the activity/inactivity hysteresis
mechanism, which will be implemented in a subsequent patch. As such,
portions of this patch prepare switch-case structures to support those
upcoming changes.
There is no txt file for it, add yaml for invensense,icp10100
which is already used in the driver. Also, document other compatibles
for ICP-101xx family and add invensense,icp10100 as a fallback.
Acked-by: Jean-Baptiste Maneyrol <jean-baptiste.maneyrol@tdk.com> Signed-off-by: Rodrigo Gobbi <rodrigo.gobbi.7@gmail.com> Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Link: https://patch.msgid.link/20250801221424.132305-1-rodrigo.gobbi.7@gmail.com Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
iio: adc: ti-adc12138: Simplify with devm_clk_get_enabled()
Driver is getting clock and almost immediately enabling it, with the
devm_request_irq() as the only relevant code executed between, thus the
probe path and cleanups can be simplified with devm_clk_get_enabled().
Move devm_request_irq() earlier, so the interrupt handler will be
registered before clock is enabled. This might be important in case
regulator supplies are enabled by other device driver and this device
raises interrupt immediately after clock sarts ticking.
The change does not reverse cleanup paths - first regulator will be
disabled, then clock and finally interrupt handler freed.
dt-bindings: iio: light: Simplify interrupts property in the example
dynaimage,al3010 and dynaimage,al3320a are I2C devices, so their
interrupts are not routed to GIC and rarely first interrupt cell is <0>.
This looks like copy-paste from some SoC block, so drop it and also for
readability use known defines instead of hard-coding interrupt flag.
dt-bindings: iio: adc: samsung,exynos-adc: Use correct IRQ level in example
The interrupt line to GIC is IRQ_TYPE_LEVEL_HIGH, so use that instead of
"none". Also replace the hard-coded GIC_SPI flag.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com> Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org> Acked-by: Rob Herring (Arm) <robh@kernel.org> Link: https://patch.msgid.link/20250724111345.47889-7-krzysztof.kozlowski@linaro.org Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
dt-bindings: iio: adc: Replace hard-coded GPIO/IRQ flag with a define
For readability use known defines instead of hard-coding GPIO or
interrupt flag.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Acked-by: Rob Herring (Arm) <robh@kernel.org> Acked-by: Matti Vaittinen <mazziesaccount@gmail.com> Link: https://patch.msgid.link/20250724111345.47889-6-krzysztof.kozlowski@linaro.org Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
dt-bindings: iio: Drop unused header includes in examples
Drop includes of headers which example code does not use. No functional
impact.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Reviewed-by: David Heidelberg <david@ixit.cz> Acked-by: Matti Vaittinen <mazziesaccount@gmail.com> Acked-by: Rob Herring (Arm) <robh@kernel.org> Link: https://patch.msgid.link/20250724111345.47889-5-krzysztof.kozlowski@linaro.org Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
David Lechner [Mon, 21 Jul 2025 22:12:47 +0000 (17:12 -0500)]
iio: adc: ti-adc081c: use individual model structures instead of array
Change the ti-adc081c driver to use individual model structures instead
of an array. This reduces the verbosity of the code. Also, the data is
now const as it should have been in the first place. The ADCxx1C_MODEL()
macro is dropped to be consistent with similar model definitions in
other drivers.
David Lechner [Mon, 21 Jul 2025 23:16:34 +0000 (18:16 -0500)]
iio: accel: bma180: use stack allocated buffer for scan
Move the scan struct to the stack instead of being in the driver state
struct. The buffer is only used in a single function and does not need
to be DMA-safe so it does not need to exist outside of that function's
scope.
David Lechner [Mon, 21 Jul 2025 22:21:08 +0000 (17:21 -0500)]
iio: proximity: srf08: use stack allocated scan buffer
Use a stack allocated scan struct in srf08_trigger_handler(). Since the
scan buffer isn't used outside of this function and doesn't need to be
DMA-safe, it doesn't need to be in struct srf08_data. We can also
eliminate an extra local variable for the return value of
srf08_read_ranging() by using scan.chan directly.
David Lechner [Tue, 22 Jul 2025 19:35:02 +0000 (14:35 -0500)]
iio: proximity: sx9500: use stack allocated struct for scan data
Use a stack-allocated struct in sx9500_trigger_handler() to hold the
IIO buffer scan data. Since the scan buffer isn't used outside of this
function, it doesn't need to be in struct sx9500_data.
By always allocating enough space for the maximum number of channels,
we can avoid having to reallocate the buffer each time buffered reads
are enabled.
David Lechner [Tue, 22 Jul 2025 21:52:38 +0000 (16:52 -0500)]
iio: fix iio_push_to_buffers_with_ts() typo
Replace iio_push_to_buffer_with_ts() with iio_push_to_buffers_with_ts()
in some documentation comments in iio.h. The latter is the correct name
of the function, the former doesn't exist.
David Lechner [Tue, 22 Jul 2025 22:26:39 +0000 (17:26 -0500)]
iio: proximity: vl53l0x-i2c: use stack allocated scan struct
Use a stack allocated struct for the scan data instead of using the
driver state to store the struct. The scan data is not used outside of
the interrupt handler function so the struct does not need to exist
outside of that scope.
David Lechner [Tue, 22 Jul 2025 22:34:45 +0000 (17:34 -0500)]
iio: proximity: pulsedlight-lidar-lite-v2: use stack allocated scan struct
Use a stack allocated struct for the scan data instead of using the
driver state to store the struct. The scan data is not used outside of
the interrupt handler function so the struct does not need to exist
outside of that scope.
David Lechner [Tue, 22 Jul 2025 22:39:17 +0000 (17:39 -0500)]
iio: proximity: mb1232: use stack allocated scan struct
Use a stack allocated struct for the scan data instead of using the
driver state to store the struct. The scan data is not used outside of
the interrupt handler function so the struct does not need to exist
outside of that scope.
Jonas Karlman [Wed, 23 Jul 2025 08:56:45 +0000 (08:56 +0000)]
dt-bindings: iio: adc: rockchip-saradc: Allow use of a power-domain
The SARADC controller in most Rockchip SoCs are part of power domains
that are always powered on, i.e. PD_BUS or PD_PERI. These always powered
on power domains have typically not been described in the device tree.
Because these power domains have been left out of the device tree there
has not been any real need to properly describe the power domain of the
SARADC controller.
On RK3528 the SARADC controller is part of the PD_VPU power domain.
Add support to describe an optional power-domains for the SARADC
controller in Rockchip SoCs.
Linus Torvalds [Sun, 10 Aug 2025 05:51:37 +0000 (08:51 +0300)]
Merge tag 'smp_urgent_for_v6.17_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull smp fixes from Borislav Petkov:
- Remove an obsolete comment and fix spelling
* tag 'smp_urgent_for_v6.17_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
cpu: Remove obsolete comment from takedown_cpu()
smp: Fix spelling in on_each_cpu_cond_mask()'s doc-comment
Linus Torvalds [Sun, 10 Aug 2025 05:46:47 +0000 (08:46 +0300)]
Merge tag 'irq_urgent_for_v6.17_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fixes from Borislav Petkov:
- Fix a wrong ioremap size in mvebu-gicp
- Remove yet another compile-test case for a driver which needs an
additional dependency
- Fix a lock inversion scenario in the IRQ unit test suite
- Remove an impossible flag situation in gic-v5
- Do not iounmap resources in gic-v5 which are managed by devm
- Make sure stale, left-over interrupts in mvebu-gicp are cleared on
driver init
- Fix a reference counting mishap in msi-lib
- Fix a dereference-before-null-ptr-check case in the riscv-imsic
irqchip driver
* tag 'irq_urgent_for_v6.17_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/mvebu-gicp: Use resource_size() for ioremap()
irqchip: Build IMX_MU_MSI only on ARM
genirq/test: Resolve irq lock inversion warnings
irqchip/gic-v5: Remove IRQD_RESEND_WHEN_IN_PROGRESS for ITS IRQs
irqchip/gic-v5: iwb: Fix iounmap probe failure path
irqchip/mvebu-gicp: Clear pending interrupts on init
irqchip/msi-lib: Fix fwnode refcount in msi_lib_irq_domain_select()
irqchip/riscv-imsic: Don't dereference before NULL pointer check
Linus Torvalds [Sun, 10 Aug 2025 05:15:32 +0000 (08:15 +0300)]
Merge tag 'x86_urgent_for_v6.17_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Borislav Petkov:
- Fix an interrupt vector setup race which leads to a non-functioning
device
- Add new Intel CPU models *and* a family: 0x12. Finally. Yippie! :-)
* tag 'x86_urgent_for_v6.17_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/irq: Plug vector setup race
x86/cpu: Add new Intel CPU model numbers for Wildcatlake and Novalake
Len Brown [Sun, 10 Aug 2025 01:08:26 +0000 (21:08 -0400)]
tools/power turbostat: version 2025.09.09
Probe and display L3 Cache topology
Add ability to average an added counter
(useful for pre-integrated "counters", such as Watts)
Break the limit of 64 built-in counters.
Assorted bug fixes and minor feature tweaks
/sys/devices/system/cpu/intel_uncore_frequency/package_X_die_Y/
may be readable by all, but
/sys/devices/system/cpu/intel_uncore_frequency/package_X_die_Y/current_freq_khz
may be readable only by root.
Non-root turbostat users see complaints in this scenario.
Fail probe of the interface if we can't read current_freq_khz.
Reported-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Original-patch-by: Zhang Rui <rui.zhang@intel.com> Signed-off-by: Len Brown <len.brown@intel.com>
Zhang Rui [Wed, 11 Jun 2025 06:50:26 +0000 (14:50 +0800)]
tools/power turbostat: Fix DMR support
Together with the RAPL MSRs, there are more MSRs gone on DMR, including
PLR (Perf Limit Reasons), and IRTL (Package cstate Interrupt Response
Time Limit) MSRs. The configurable TDP info should also be retrieved
from TPMI based Intel Speed Select Technology feature.
Remove the access of these MSRs for DMR. Improve the DMR platform
feature table to make it more readable at the same time.
Fixes: 83075bd59de2 ("tools/power turbostat: Add initial support for DMR") Signed-off-by: Zhang Rui <rui.zhang@intel.com> Signed-off-by: Len Brown <len.brown@intel.com>
tools/power turbostat: add format "average" for external attributes
External atributes with format "raw" are not printed in summary lines
for nodes/packages (or with option -S). The new format "average"
behaves like "raw" but also adds the summary data
Signed-off-by: Michael Hebenstreit <michael.hebenstreit@intel.com> Signed-off-by: Len Brown <len.brown@intel.com>
Len Brown [Sat, 12 Jul 2025 20:16:56 +0000 (16:16 -0400)]
tools/power turbostat: Support more than 64 built-in-counters
We have out-grown the ability to use a 64-bit memory location
to inventory every possible built-in counter.
Leverage the the CPU_SET(3) macros to break this barrier.
Also, break the Joules & Watts counters into two,
since we can no longer 'or' them together...
Linus Torvalds [Sat, 9 Aug 2025 15:12:23 +0000 (18:12 +0300)]
Merge tag 'tty-6.16-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull TTY fix from Greg KH:
"Here is a single revert of one of the previous patches that went in
the last tty/serial merge that is breaking userspace on some platforms
(specifically powerpc, probably a few others.)
It accidentially changed the ioctl values of some tty ioctls, which
breaks xorg.
The revert has been in linux-next all this week with no reported
issues"
* tag 'tty-6.16-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
Revert "tty: vt: use _IO() to define ioctl numbers"
Linus Torvalds [Sat, 9 Aug 2025 05:47:28 +0000 (08:47 +0300)]
Merge tag 'block-6.17-20250808' of git://git.kernel.dk/linux
Pull more block updates from Jens Axboe:
- MD pull request via Yu:
- mddev null-ptr-dereference fix, by Erkun
- md-cluster fail to remove the faulty disk regression fix, by
Heming
- minor cleanup, by Li Nan and Jinchao
- mdadm lifetime regression fix reported by syzkaller, by Yu Kuai
- MD pull request via Christoph
- add support for getting the FDP featuee in fabrics passthru path
(Nitesh Shetty)
- add capability to connect to an administrative controller
(Kamaljit Singh)
- fix a leak on sgl setup error (Keith Busch)
- initialize discovery subsys after debugfs is initialized
(Mohamed Khalfella)
- fix various comment typos (Bjorn Helgaas)
- remove unneeded semicolons (Jiapeng Chong)
- nvmet debugfs ordering issue fix
- Fix UAF in the tag_set in zloop
- Ensure sbitmap shallow depth covers entire set
- Reduce lock roundtrips in io context lookup
- Move scheduler tags alloc/free out of elevator and freeze lock, to
fix some lockdep found issues
- Improve robustness of queue limits checking
- Fix a regression with IO priorities, if no io context exists
* tag 'block-6.17-20250808' of git://git.kernel.dk/linux: (26 commits)
lib/sbitmap: make sbitmap_get_shallow() internal
lib/sbitmap: convert shallow_depth from one word to the whole sbitmap
nvmet: exit debugfs after discovery subsystem exits
block, bfq: Reorder struct bfq_iocq_bfqq_data
md: make rdev_addable usable for rcu mode
md/raid1: remove struct pool_info and related code
md/raid1: change r1conf->r1bio_pool to a pointer type
block: ensure discard_granularity is zero when discard is not supported
zloop: fix KASAN use-after-free of tag set
block: Fix default IO priority if there is no IO context
nvme: fix various comment typos
nvme-auth: remove unneeded semicolon
nvme-pci: fix leak on sgl setup error
nvmet: initialize discovery subsys after debugfs is initialized
nvme: add capability to connect to an administrative controller
nvmet: add support for FDP in fabrics passthru path
md: rename recovery_cp to resync_offset
md/md-cluster: handle REMOVE message earlier
md: fix create on open mddev lifetime regression
block: fix potential deadlock while running nr_hw_queue update
...
Linus Torvalds [Sat, 9 Aug 2025 05:45:08 +0000 (08:45 +0300)]
Merge tag 'io_uring-6.17-20250808' of git://git.kernel.dk/linux
Pull io_uring fixes from Jens Axboe:
- Allow vectorized payloads for send/send-zc - like sendmsg, but
without the hassle of a msghdr.
- Fix for an integer wrap that should go to stable, spotted by syzbot.
Nothing alarming here, as you need to be root to hit this.
Nevertheless, it should get fixed.
FWIW, kudos to the syzbot crew for having much nicer reproducers now,
and with nicely annotated source code as well. This is particularly
useful as syzbot uses the raw interface rather than liburing,
historically it's been difficult to turn a syzbot reproducer into a
meaningful test case. With the recent changes, not true anymore!
* tag 'io_uring-6.17-20250808' of git://git.kernel.dk/linux:
io_uring/memmap: cast nr_pages to size_t before shifting
io_uring/net: Allow to do vectorized send
Linus Torvalds [Sat, 9 Aug 2025 05:43:24 +0000 (08:43 +0300)]
Merge tag 'spi-fix-v6.17-merge-window' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"There's one fix here for an issue with the CS42L43 where we were
allocating a single property for client devices as just that property
rather than a terminated array of properties like we are supposed to.
We also have an update to the MAINTAINERS file for some Renesas
devices"
* tag 'spi-fix-v6.17-merge-window' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: cs42l43: Property entry should be a null-terminated array
MAINTAINERS: Add entries for the RZ/V2H(P) RSPI
Linus Torvalds [Sat, 9 Aug 2025 05:41:53 +0000 (08:41 +0300)]
Merge tag 'regulator-fix-v6.17-merge-window' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fix from Mark Brown:
"This fixes an issue with the newly added code for handling large
voltage changes on regulators which require that individual voltage
changes cover a limited range, the check for convergence was broken"
* tag 'regulator-fix-v6.17-merge-window' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: core: correct convergence check in regulator_set_voltage()
Linus Torvalds [Sat, 9 Aug 2025 05:40:28 +0000 (08:40 +0300)]
Merge tag 'regmap-fix-v6.17-merge-window' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap fixes from Mark Brown:
"These patches fix a lockdep issue Russell King reported with nested
regmap-irqs (unusual since regmap is generally for devices on slow
buses so devices don't get nested), plus add a missing mutex free
which I noticed while implementing a fix for that issue"
* tag 'regmap-fix-v6.17-merge-window' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: irq: Avoid lockdep warnings with nested regmap-irq chips
regmap: irq: Free the regmap-irq mutex
Linus Torvalds [Sat, 9 Aug 2025 05:37:17 +0000 (08:37 +0300)]
Merge tag 'mailbox-v6.17' of git://git.kernel.org/pub/scm/linux/kernel/git/jassibrar/mailbox
Pull mailbox updates from Jassi Brar:
- aspeed: add driver and bindings for ast2700
- broadcom: add driver and bindings for bcm74110
- mediatek: fix RPM api usage
- qcom: use dev_fwnode
- pcc: support shared buffer
- misc dt-bindings cleanup
* tag 'mailbox-v6.17' of git://git.kernel.org/pub/scm/linux/kernel/git/jassibrar/mailbox:
mailbox/pcc: support mailbox management of the shared buffer
mailbox: bcm74110: Fix spelling mistake
mailbox: bcm74110: remove unneeded semicolon
mailbox: aspeed: add mailbox driver for AST27XX series SoC
dt-bindings: mailbox: Add ASPEED AST2700 series SoC
dt-bindings: mailbox: Drop consumers example DTS
dt-bindings: mailbox: nvidia,tegra186-hsp: Use generic node name
dt-bindings: mailbox: Correct example indentation
dt-bindings: mailbox: ti,secure-proxy: Add missing reg maxItems
dt-bindings: mailbox: amlogic,meson-gxbb-mhu: Add missing interrupts maxItems
dt-bindings: mailbox: qcom-ipcc: document the Milos Inter-Processor Communication Controller
mailbox: Add support for bcm74110
dt-bindings: mailbox: Add support for bcm74110
mailbox: Use dev_fwnode()
mailbox: mtk-cmdq: Switch to pm_runtime_put_autosuspend()
Linus Torvalds [Sat, 9 Aug 2025 05:15:43 +0000 (08:15 +0300)]
Merge tag 'gpio-updates-for-v6.17-rc1-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux
Pull gpio updates from Bartosz Golaszewski:
"As discussed: there's a small commit that removes the legacy GPIO line
value setter callbacks as they're no longer used and a big, treewide
commit that renames the new ones to the old names across all GPIO
drivers at once.
While at it: there are also two fixes that I picked up over the course
of the merge window:
- remove unused, legacy GPIO line value setters from struct gpio_chip
- rename the new set callbacks back to the original names treewide
- fix interrupt handling in gpio-mlxbf2
- revert a buggy immutable irqchip conversion"
* tag 'gpio-updates-for-v6.17-rc1-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux:
treewide: rename GPIO set callbacks back to their original names
gpio: remove legacy GPIO line value setter callbacks
gpio: mlxbf2: use platform_get_irq_optional()
Revert "gpio: pxa: Make irq_chip immutable"
Linus Torvalds [Sat, 9 Aug 2025 05:12:41 +0000 (08:12 +0300)]
Merge tag 'sound-fix-6.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
- Support for ASoC AMD ACP 7.2 with new IDs
- ASoC Intel AVS and SOF fixes
- Yet more kconfig adjustments for HD-audio codecs
- TAS2781 codec fixes
- Fixes for longstanding (rather minor) bugs in Intel LPE audio and
USB-audio drivers
* tag 'sound-fix-6.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda/cirrus: Restrict prompt only for CONFIG_EXPERT
ALSA: hda/hdmi: Restrict prompt only for CONFIG_EXPERT
ALSA: hda/realtek: Restrict prompt only for CONFIG_EXPERT
ALSA: hda/ca0132: Fix missing error handling in ca0132_alt_select_out()
ASoC: SOF: Intel: hda-sdw-bpt: fix SND_SOF_SOF_HDA_SDW_BPT dependencies
ALSA: hda/tas2781: Support L"SmartAmpCalibrationData" to save calibrated data
ALSA: intel_hdmi: Fix off-by-one error in __hdmi_lpe_audio_probe()
ALSA: hda/realtek: add LG gram 16Z90R-A to alc269 fixup table
ALSA: usb-audio: Don't use printk_ratelimit for debug prints
ASoC: Intel: sof_sdw: Add quirk for Alienware Area 51 (2025) 0CCC SKU
ASoC: tas2781: Fix the wrong step for TLV on tas2781
ASoC: amd: acp: Add SoundWire SOF machine driver support for acp7.2 platform
ASoC: amd: acp: Add SoundWire legacy machine driver support for acp7.2 platform
ASoC: amd: ps: Add SoundWire pci and dma driver support for acp7.2 platform
ASoC: SOF: amd: Add sof audio support for acp7.2 platform
ASoC: Intel: avs: Fix uninitialized pointer error in probe()
ASoC: wm8962: Clear master mode when enter runtime suspend
ASoC: SOF: amd: acp-loader: Use GFP_KERNEL for DMA allocations in resume context
Linus Torvalds [Sat, 9 Aug 2025 04:58:55 +0000 (07:58 +0300)]
Merge tag 'soc-fixes-6.17-1' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull SoC fixes from Arnd Bergmann:
"These are a few patches to fix up bits that went missing during the
merge window: The tegra and s3c patches address trivial regressions
from conflicts, the bcm7445 makes the dt conform to the binding that
was made stricter"
* tag 'soc-fixes-6.17-1' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
arm64: tegra: Remove numa-node-id properties
ARM: s3c/gpio: complete the conversion to new GPIO value setters
ARM: dts: broadcom: Fix bcm7445 memory controller compatible
Linus Torvalds [Sat, 9 Aug 2025 04:35:03 +0000 (07:35 +0300)]
Merge tag 'xtensa-20250808' of https://github.com/jcmvbkbc/linux-xtensa
Pull xtensa update from Max Filippov:
- replace __ASSEMBLY__ with __ASSEMBLER__ in arch headers
* tag 'xtensa-20250808' of https://github.com/jcmvbkbc/linux-xtensa:
xtensa: Replace __ASSEMBLY__ with __ASSEMBLER__ in non-uapi headers
xtensa: Replace __ASSEMBLY__ with __ASSEMBLER__ in uapi headers
Linus Torvalds [Sat, 9 Aug 2025 04:26:19 +0000 (07:26 +0300)]
Merge tag 'v6.17-p2' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6
Pull crypto fix from Herbert Xu:
"Fix a regression that broke hmac(sha3-224-s390)"
* tag 'v6.17-p2' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: hash - Increase HASH_MAX_DESCSIZE for hmac(sha3-224-s390)
Linus Torvalds [Sat, 9 Aug 2025 04:20:44 +0000 (07:20 +0300)]
Merge tag 'nfs-for-6.17-1' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull NFS client updates from Trond Myklebust:
"Highlights include:
Stable fixes:
- don't inherit NFS filesystem capabilities when crossing from one
filesystem to another
Bugfixes:
- NFS wakeup of __nfs_lookup_revalidate() needs memory barriers
- NFS improve bounds checking in nfs_fh_to_dentry()
- NFS Fix allocation errors when writing to a NFS file backed
loopback device
- NFSv4: More listxattr fixes
- SUNRPC: fix client handling of TLS alerts
- pNFS block/scsi layout fix for an uninitialised pointer
dereference
- pNFS block/scsi layout fixes for the extent encoding, stripe
mapping, and disk offset overflows
- pNFS layoutcommit work around for RPC size limitations
- pNFS/flexfiles avoid looping when handling fatal errors after
layoutget
- localio: fix various race conditions
Features and cleanups:
- Add NFSv4 support for retrieving the btime
- NFS: Allow folio migration for the case of mode == MIGRATE_SYNC
- NFS: Support using a kernel keyring to store TLS certificates
- NFSv4: Speed up delegation lookup using a hash table
- Assorted cleanups to remove unused variables and struct fields
- Assorted new tracepoints to improve debugging"
* tag 'nfs-for-6.17-1' of git://git.linux-nfs.org/projects/trondmy/linux-nfs: (44 commits)
NFS/localio: nfs_uuid_put() fix the wake up after unlinking the file
NFS/localio: nfs_uuid_put() fix races with nfs_open/close_local_fh()
NFS/localio: nfs_close_local_fh() fix check for file closed
NFSv4: Remove duplicate lookups, capability probes and fsinfo calls
NFS: Fix the setting of capabilities when automounting a new filesystem
sunrpc: fix client side handling of tls alerts
nfs/localio: use read_seqbegin() rather than read_seqbegin_or_lock()
NFS: Fixup allocation flags for nfsiod's __GFP_NORETRY
NFSv4.2: another fix for listxattr
NFS: Fix filehandle bounds checking in nfs_fh_to_dentry()
SUNRPC: Silence warnings about parameters not being described
NFS: Clean up pnfs_put_layout_hdr()/pnfs_destroy_layout_final()
NFS: Fix wakeup of __nfs_lookup_revalidate() in unblock_revalidate()
NFS: use a hash table for delegation lookup
NFS: track active delegations per-server
NFS: move the delegation_watermark module parameter
NFS: cleanup nfs_inode_reclaim_delegation
NFS: cleanup error handling in nfs4_server_common_setup
pNFS/flexfiles: don't attempt pnfs on fatal DS errors
NFS: drop __exit from nfs_exit_keyring
...
Linus Torvalds [Sat, 9 Aug 2025 04:12:43 +0000 (07:12 +0300)]
Merge tag 'v6.17rc-part2-SMB3-client-fixes' of git://git.samba.org/sfrench/cifs-2.6
Pull more smb client updates from Steve French:
"Non-smbdirect:
- Fix null ptr deref caused by delay in global spinlock
initialization
- Two fixes for native symlink creation with SMB3.1.1 POSIX
Extensions
- Fix for socket special file creation with SMB3.1.1 POSIX Exensions
- Reduce lock contention by splitting out mid_counter_lock
- move SMB1 transport code to separate file to reduce module size
when support for legacy servers is disabled
- Two cleanup patches: rename mid_lock to make it clearer what it
protects and one to convert mid flags to bool to make clearer
Smbdirect/RDMA restructuring and fixes:
- Fix for error handling in send done
- Remove unneeded empty packet queue
- Fix put_receive_buffer error path
- Two fixes to recv_done error paths
- Remove unused variable
- Improve response and recvmsg type handling
- Fix handling of incoming message type
- Two cleanup fixes for better handling smbdirect recv io
- Two cleanup fixes for socket spinlock
- Two patches that add socket reassembly struct
- Remove unused connection_status enum
- Use flag in common header for SMBDIRECT_RECV_IO_MAX_SGE
- Two cleanup patches to introduce and use smbdirect send io
- Two cleanup patches to introduce and use smbdirect send_io struct
- Fix to return error if rdma connect takes longer than 5 seconds
- Error logging improvements
- Fix redundand call to init_waitqueue_head
- Remove unneeded wait queue"
* tag 'v6.17rc-part2-SMB3-client-fixes' of git://git.samba.org/sfrench/cifs-2.6: (33 commits)
smb: client: only use a single wait_queue to monitor smbdirect connection status
smb: client: don't call init_waitqueue_head(&info->conn_wait) twice in _smbd_get_connection
smb: client: improve logging in smbd_conn_upcall()
smb: client: return an error if rdma_connect does not return within 5 seconds
smb: client: make use of smbdirect_socket.{send,recv}_io.mem.{cache,pool}
smb: smbdirect: add smbdirect_socket.{send,recv}_io.mem.{cache,pool}
smb: client: make use of struct smbdirect_send_io
smb: smbdirect: introduce struct smbdirect_send_io
smb: client: make use of SMBDIRECT_RECV_IO_MAX_SGE
smb: smbdirect: add SMBDIRECT_RECV_IO_MAX_SGE
smb: client: remove unused enum smbd_connection_status
smb: client: make use of smbdirect_socket.recv_io.reassembly.*
smb: smbdirect: introduce smbdirect_socket.recv_io.reassembly.*
smb: client: make use of smb: smbdirect_socket.recv_io.free.{list,lock}
smb: smbdirect: introduce smbdirect_socket.recv_io.free.{list,lock}
smb: client: make use of struct smbdirect_recv_io
smb: smbdirect: introduce struct smbdirect_recv_io
smb: client: make use of smbdirect_socket->recv_io.expected
smb: smbdirect: introduce smbdirect_socket.recv_io.expected
smb: client: remove unused smbd_connection->fragment_reassembly_remaining
...
Linus Torvalds [Sat, 9 Aug 2025 03:52:37 +0000 (06:52 +0300)]
Merge tag 'v6.17rc-part2-ksmbd-server-fixes' of git://git.samba.org/ksmbd
Pull smb server fixes from Steve French:
- Fix limiting repeated connections from same IP
- Fix for extracting shortname when name begins with a dot
- Four smbdirect fixes:
- three fixes to the receive path: potential unmap bug, potential
resource leaks and stale connections, and also potential use
after free race
- cleanup to remove unneeded queue
* tag 'v6.17rc-part2-ksmbd-server-fixes' of git://git.samba.org/ksmbd:
smb: server: Fix extension string in ksmbd_extract_shortname()
ksmbd: limit repeated connections from clients with the same IP
smb: server: let recv_done() avoid touching data_transfer after cleanup/move
smb: server: let recv_done() consistently call put_recvmsg/smb_direct_disconnect_rdma_connection
smb: server: make sure we call ib_dma_unmap_single() only if we called ib_dma_map_single already
smb: server: remove separate empty_recvmsg_queue
Zhang Rui [Tue, 17 Jun 2025 12:48:59 +0000 (20:48 +0800)]
tools/power turbostat: Fix bogus SysWatt for forked program
Similar to delta_cpu(), delta_platform() is called in turbostat main
loop. This ensures accurate SysWatt readings in periodic monitoring mode
$ sudo turbostat -S -q --show power -i 1
CoreTmp PkgTmp PkgWatt CorWatt GFXWatt RAMWatt PKG_% RAM_% SysWatt
60 61 6.21 1.13 0.16 0.00 0.00 0.00 13.07
58 61 6.00 1.07 0.18 0.00 0.00 0.00 12.75
58 61 5.74 1.05 0.17 0.00 0.00 0.00 12.22
58 60 6.27 1.11 0.24 0.00 0.00 0.00 13.55
However, delta_platform() is missing for forked program and causes bogus
SysWatt reporting,
$ sudo turbostat -S -q --show power sleep 1
1.004736 sec
CoreTmp PkgTmp PkgWatt CorWatt GFXWatt RAMWatt PKG_% RAM_% SysWatt
57 58 6.05 1.02 0.16 0.00 0.00 0.00 0.03
Add missing delta_platform() for forked program.
Fixes: e5f687b89bc2 ("tools/power turbostat: Add RAPL psys as a built-in counter") Signed-off-by: Zhang Rui <rui.zhang@intel.com> Signed-off-by: Len Brown <len.brown@intel.com>
Kernels configured with CONFIG_MULTIUSER=n have no cap_get_proc().
Check for ENOSYS to recognize this case, and continue on to
attempt to access the requested MSRs (such as temperature).
Signed-off-by: Calvin Owens <calvin@wbinvd.org> Signed-off-by: Len Brown <len.brown@intel.com>
projects / thirdparty / kernel / stable.git / log
