tidss_crtc_atomic_flush() checks if the crtc is enabled, and if not,
returns immediately as there's no reason to do any register changes.
However, the code checks for 'crtc->state->enable', which does not
reflect the actual HW state. We should instead look at the
'crtc->state->active' flag.
This causes the tidss_crtc_atomic_flush() to proceed with the flush even
if the active state is false, which then causes us to hit the
WARN_ON(!crtc->state->event) check.
Fix this by checking the active flag, and while at it, fix the related
debug print which had "active" and "needs modeset" wrong way.
Cc: <stable@vger.kernel.org> Fixes: 32a1795f57ee ("drm/tidss: New driver for TI Keystone platform Display SubSystem") Reviewed-by: Aradhya Bhatia <a-bhatia1@ti.com> Link: https://lore.kernel.org/r/20231109-tidss-probe-v2-10-ac91b5ea35c0@ideasonboard.com Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The i2c_master_send/recv() functions return negative error codes or the
number of bytes that were able to be sent/received. This code has
two problems. 1) Instead of checking if all the bytes were sent or
received, it checks that at least one byte was sent or received.
2) If there was a partial send/receive then we should return a negative
error code but this code returns success.
Fixes: a9fe713d7d45 ("drm/bridge: Add PTN3460 bridge driver") Cc: stable@vger.kernel.org Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org> Reviewed-by: Robert Foss <rfoss@kernel.org> Signed-off-by: Robert Foss <rfoss@kernel.org> Link: https://patchwork.freedesktop.org/patch/msgid/0cdc2dce-ca89-451a-9774-1482ab2f4762@moroto.mountain Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On HSW non-ULT (or at least on Dell Latitude E6540) external displays
start to flicker when we enable PSR on the eDP. We observe a much higher
SR and PC6 residency than should be possible with an external display,
and indeen much higher than what we observe with eDP disabled and
only the external display enabled. Looks like the hardware is somehow
ignoring the fact that the external display is active during PSR.
I wasn't able to redproduce this on my HSW ULT machine, or BDW.
So either there's something specific about this particular laptop
(eg. some unknown firmware thing) or the issue is limited to just
non-ULT HSW systems. All known registers that could affect this
look perfectly reasonable on the affected machine.
As a workaround let's unmask the LPSP event to prevent PSR entry
except while in LPSP mode (only pipe A + eDP active). This
will prevent PSR entry entirely when multiple pipes are active.
The one slight downside is that we now also prevent PSR entry
when driving eDP with pipe B or C, but I think that's a reasonable
tradeoff to avoid having to implement a more complex workaround.
If we get a deadlock after the fb lookup in drm_mode_page_flip_ioctl()
we proceed to unref the fb and then retry the whole thing from the top.
But we forget to reset the fb pointer back to NULL, and so if we then
get another error during the retry, before the fb lookup, we proceed
the unref the same fb again without having gotten another reference.
The end result is that the fb will (eventually) end up being freed
while it's still in use.
Reset fb to NULL once we've unreffed it to avoid doing it again
until we've done another fb lookup.
This turned out to be pretty easy to hit on a DG2 when doing async
flips (and CONFIG_DEBUG_WW_MUTEX_SLOWPATH=y). The first symptom I
saw that drm_closefb() simply got stuck in a busy loop while walking
the framebuffer list. Fortunately I was able to convince it to oops
instead, and from there it was easier to track down the culprit.
Lenovo 82TQ is unhappy if we do the display on sequence this
late. The display output shows severe corruption.
It's unclear if this is a failure on our part (perhaps
something to do with sending commands in LP mode after HS
/video mode transmission has been started? Though the backlight
on command at least seems to work) or simply that there are
some commands in the sequence that are needed to be done
earlier (eg. could be some DSC init stuff?). If the latter
then I don't think the current Windows code would work
either, but maybe this was originally tested with an older
driver, who knows.
Root causing this fully would likely require a lot of
experimentation which isn't really feasible without direct
access to the machine, so let's just accept failure and
go back to the original sequence.
This commit causes some regressions in desktop usage, this will
reintroduce the original deadlock in DRI_PRIME situations, I've
got an idea to fix it by offloading to a workqueue in a different
spot, however this code has a race condition where we sometimes
miss interrupts so I'd like to fix that as well.
Cc: stable@vger.kernel.org Signed-off-by: Dave Airlie <airlied@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On systems using HWP, if a given frequency is equal to the maximum turbo
frequency or the maximum non-turbo frequency, the HWP performance level
corresponding to it is already known and can be used directly without
any computation.
Accordingly, adjust the code to use the known HWP performance levels in
the cases mentioned above.
This also helps to avoid limiting CPU capacity artificially in some
cases when the BIOS produces the HWP_CAP numbers using a different
E-core-to-P-core performance scaling factor than expected by the kernel.
Fixes: f5c8cf2a4992 ("cpufreq: intel_pstate: hybrid: Use known scaling factor for P-cores") Cc: 6.1+ <stable@vger.kernel.org> # 6.1+ Tested-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Recently xfs/513 started failing on my test machines testing "-o
ro,norecovery" mount options. This was being emitted in dmesg:
[ 9906.932724] XFS (pmem0): no-recovery mounts must be read-only.
Turns out, readonly mounts with the fsopen()/fsconfig() mount API
have been busted since day zero. It's only taken 5 years for debian
unstable to start using this "new" mount API, and shortly after this
I noticed xfs/513 had started to fail as per above.
Showing that the actual mount instantiation (FSCONFIG_CMD_CREATE) is
what threw out the error.
During mount instantiation, we call xfs_fs_validate_params() which
does:
/* No recovery flag requires a read-only mount */
if (xfs_has_norecovery(mp) && !xfs_is_readonly(mp)) {
xfs_warn(mp, "no-recovery mounts must be read-only.");
return -EINVAL;
}
and xfs_is_readonly() checks internal mount flags for read only
state. This state is set in xfs_init_fs_context() from the
context superblock flag state:
/*
* Copy binary VFS mount flags we are interested in.
*/
if (fc->sb_flags & SB_RDONLY)
set_bit(XFS_OPSTATE_READONLY, &mp->m_opstate);
With the old mount API, all of the VFS specific superblock flags
had already been parsed and set before xfs_init_fs_context() is
called, so this all works fine.
However, in the brave new fsopen/fsconfig world,
xfs_init_fs_context() is called from fsopen() context, before any
VFS superblock have been set or parsed. Hence if we use fsopen(),
the internal XFS readonly state is *never set*. Hence anything that
depends on xfs_is_readonly() actually returning true for read only
mounts is broken if fsopen() has been used to mount the filesystem.
Fix this by moving this internal state initialisation to
xfs_fs_fill_super() before we attempt to validate the parameters
that have been set prior to the FSCONFIG_CMD_CREATE call being made.
Signed-off-by: Dave Chinner <dchinner@redhat.com> Fixes: 73e5fff98b64 ("xfs: switch to use the new mount-api")
cc: stable@vger.kernel.org Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Chandan Babu R <chandanbabu@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the RLC firmware is invalid because of wrong header size,
the pointer to the rlc firmware is released in function
amdgpu_ucode_request. There will be a null pointer error
in subsequent use. So skip validation to fix it.
Fixes: 3da9b71563cb ("drm/amd: Use `amdgpu_ucode_*` helpers for GFX10") Signed-off-by: Ma Jun <Jun.Ma2@amd.com> Acked-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 60aebc9559492cea ("drivers/firmware: Move sysfb_init() from
device_initcall to subsys_initcall_sync") messes up initialization order
of the graphics drivers and leads to blank displays on some systems. So
revert the commit.
To make the display drivers fully independent from initialization
order requires to track framebuffer memory by device and independently
from the loaded drivers. The kernel currently lacks the infrastructure
to do so.
Reported-by: Jaak Ristioja <jaak@ristioja.ee> Closes: https://lore.kernel.org/dri-devel/ZUnNi3q3yB3zZfTl@P70.localdomain/T/#t Reported-by: Huacai Chen <chenhuacai@loongson.cn> Closes: https://lore.kernel.org/dri-devel/20231108024613.2898921-1-chenhuacai@loongson.cn/ Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/10133 Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de> Cc: Javier Martinez Canillas <javierm@redhat.com> Cc: Thorsten Leemhuis <regressions@leemhuis.info> Cc: Jani Nikula <jani.nikula@linux.intel.com> Cc: stable@vger.kernel.org # v6.5+ Reviewed-by: Javier Martinez Canillas <javierm@redhat.com> Acked-by: Jani Nikula <jani.nikula@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20240123120937.27736-1-tzimmermann@suse.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On reception of a completion interrupt the shared memory area is accessed
to retrieve the message header at first and then, if the message sequence
number identifies a transaction which is still pending, the related
payload is fetched too.
When an SCMI command times out the channel ownership remains with the
platform until eventually a late reply is received and, as a consequence,
any further transmission attempt remains pending, waiting for the channel
to be relinquished by the platform.
Once that late reply is received the channel ownership is given back
to the agent and any pending request is then allowed to proceed and
overwrite the SMT area of the just delivered late reply; then the wait
for the reply to the new request starts.
It has been observed that the spurious IRQ related to the late reply can
be wrongly associated with the freshly enqueued request: when that happens
the SCMI stack in-flight lookup procedure is fooled by the fact that the
message header now present in the SMT area is related to the new pending
transaction, even though the real reply has still to arrive.
This race-condition on the A2P channel can be detected by looking at the
channel status bits: a genuine reply from the platform will have set the
channel free bit before triggering the completion IRQ.
Add a consistency check to validate such condition in the A2P ISR.
Reported-by: Xinglong Yang <xinglong.yang@cixtech.com> Closes: https://lore.kernel.org/all/PUZPR06MB54981E6FA00D82BFDBB864FBF08DA@PUZPR06MB5498.apcprd06.prod.outlook.com/ Fixes: 5c8a47a5a91d ("firmware: arm_scmi: Make scmi core independent of the transport type") Cc: stable@vger.kernel.org # 5.15+ Signed-off-by: Cristian Marussi <cristian.marussi@arm.com> Tested-by: Xinglong Yang <xinglong.yang@cixtech.com> Link: https://lore.kernel.org/r/20231220172112.763539-1-cristian.marussi@arm.com Signed-off-by: Sudeep Holla <sudeep.holla@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Similar to a reported issue (check the commit b33fb5b801c6 ("net:
qualcomm: rmnet: fix global oob in rmnet_policy"), my local fuzzer finds
another global out-of-bounds read for policy ksmbd_nl_policy. See bug
trace below:
==================================================================
BUG: KASAN: global-out-of-bounds in validate_nla lib/nlattr.c:386 [inline]
BUG: KASAN: global-out-of-bounds in __nla_validate_parse+0x24af/0x2750 lib/nlattr.c:600
Read of size 1 at addr ffffffff8f24b100 by task syz-executor.1/62810
To fix it, add a placeholder named __KSMBD_EVENT_MAX and let
KSMBD_EVENT_MAX to be its original value - 1 according to what other
netlink families do. Also change two sites that refer the
KSMBD_EVENT_MAX to correct value.
Cc: stable@vger.kernel.org Fixes: 0626e6641f6b ("cifsd: add server handler for central processing and tranport layers") Signed-off-by: Lin Ma <linma@zju.edu.cn> Acked-by: Namjae Jeon <linkinjeon@kernel.org> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
p2sb_bar() unhides P2SB device to get resources from the device. It
guards the operation by locking pci_rescan_remove_lock so that parallel
rescans do not find the P2SB device. However, this lock causes deadlock
when PCI bus rescan is triggered by /sys/bus/pci/rescan. The rescan
locks pci_rescan_remove_lock and probes PCI devices. When PCI devices
call p2sb_bar() during probe, it locks pci_rescan_remove_lock again.
Hence the deadlock.
To avoid the deadlock, do not lock pci_rescan_remove_lock in p2sb_bar().
Instead, do the lock at fs_initcall. Introduce p2sb_cache_resources()
for fs_initcall which gets and caches the P2SB resources. At p2sb_bar(),
refer the cache and return to the caller.
Before operating the device at P2SB DEVFN for resource cache, check
that its device class is PCI_CLASS_MEMORY_OTHER 0x0580 that PCH
specifications define. This avoids unexpected operation to other devices
at the same DEVFN.
Link: https://lore.kernel.org/linux-pci/6xb24fjmptxxn5js2fjrrddjae6twex5bjaftwqsuawuqqqydx@7cl3uik5ef6j/ Fixes: 9745fb07474f ("platform/x86/intel: Add Primary to Sideband (P2SB) bridge support") Cc: stable@vger.kernel.org Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com> Link: https://lore.kernel.org/r/20240108062059.3583028-2-shinichiro.kawasaki@wdc.com Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Tested-by Klara Modin <klarasmodin@gmail.com> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When booting a kernel with CONFIG_CFI_CLANG, there is a CFI failure when
accessing any of the values under
/sys/devices/system/cpu/intel_uncore_frequency/package_00_die_00:
$ cat /sys/devices/system/cpu/intel_uncore_frequency/package_00_die_00/max_freq_khz
fish: Job 1, 'cat /sys/devices/system/cpu/int…' terminated by signal SIGSEGV (Address boundary error)
The sysfs callback functions such as show_domain_id() are written as if
they are going to be called by dev_attr_show() but as the above message
shows, they are instead called by kobj_attr_show(). kCFI checks that the
destination of an indirect jump has the exact same type as the prototype
of the function pointer it is called through and fails when they do not.
These callbacks are called through kobj_attr_show() because
uncore_root_kobj was initialized with kobject_create_and_add(), which
means uncore_root_kobj has a ->sysfs_ops of kobj_sysfs_ops from
kobject_create(), which uses kobj_attr_show() as its ->show() value.
The only reason there has not been a more noticeable problem until this
point is that 'struct kobj_attribute' and 'struct device_attribute' have
the same layout, so getting the callback from container_of() works the
same with either value.
Change all the callbacks and their uses to be compatible with
kobj_attr_show() and kobj_attr_store(), which resolves the kCFI failure
and allows the sysfs files to work properly.
Closes: https://github.com/ClangBuiltLinux/linux/issues/1974 Fixes: ae7b2ce57851 ("platform/x86/intel/uncore-freq: Use sysfs API to create attributes") Cc: stable@vger.kernel.org Signed-off-by: Nathan Chancellor <nathan@kernel.org> Reviewed-by: Sami Tolvanen <samitolvanen@google.com> Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> Link: https://lore.kernel.org/r/20240104-intel-uncore-freq-kcfi-fix-v1-1-bf1e8939af40@kernel.org Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
core.c:nf_hook_slow assumes that the upper 16 bits of NF_DROP
verdicts contain a valid errno, i.e. -EPERM, -EHOSTUNREACH or similar,
or 0.
Due to the reverted commit, its possible to provide a positive
value, e.g. NF_ACCEPT (1), which results in use-after-free.
Its not clear to me why this commit was made.
NF_QUEUE is not used by nftables; "queue" rules in nftables
will result in use of "nft_queue" expression.
If we later need to allow specifiying errno values from userspace
(do not know why), this has to call NF_DROP_GETERR and check that
"err <= 0" holds true.
Remove netdevice from inet/ingress basechain in case NETDEV_UNREGISTER
event is reported, otherwise a stale reference to netdevice remains in
the hook list.
Current code in netvsc_drv_init() incorrectly assumes that PAGE_SIZE
is 4 Kbytes, which is wrong on ARM64 with 16K or 64K page size. As a
result, the default VMBus ring buffer size on ARM64 with 64K page size
is 8 Mbytes instead of the expected 512 Kbytes. While this doesn't break
anything, a typical VM with 8 vCPUs and 8 netvsc channels wastes 120
Mbytes (8 channels * 2 ring buffers/channel * 7.5 Mbytes/ring buffer).
Unfortunately, the module parameter specifying the ring buffer size
is in units of 4 Kbyte pages. Ideally, it should be in units that
are independent of PAGE_SIZE, but backwards compatibility prevents
changing that now.
Fix this by having netvsc_drv_init() hardcode 4096 instead of using
PAGE_SIZE when calculating the ring buffer size in bytes. Also
use the VMBUS_RING_SIZE macro to ensure proper alignment when running
with page size larger than 4K.
Cc: <stable@vger.kernel.org> # 5.15.x Fixes: 7aff79e297ee ("Drivers: hv: Enable Hyper-V code to be built on ARM64") Signed-off-by: Michael Kelley <mhklinux@outlook.com> Link: https://lore.kernel.org/r/20240122162028.348885-1-mhklinux@outlook.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
An opaque directory cannot have xwhiteouts, so instead of marking an
xwhiteouts directory with a new xattr, overload overlay.opaque xattr
for marking both opaque dir ('y') and xwhiteouts dir ('x').
This is more efficient as the overlay.opaque xattr is checked during
lookup of directory anyway.
This also prevents unnecessary checking the xattr when reading a
directory without xwhiteouts, i.e. most of the time.
Note that the xwhiteouts marker is not checked on the upper layer and
on the last layer in lowerstack, where xwhiteouts are not expected.
Fixes: bc8df7a3dc03 ("ovl: Add an alternative type of whiteout") Cc: <stable@vger.kernel.org> # v6.7 Reviewed-by: Alexander Larsson <alexl@redhat.com> Tested-by: Alexander Larsson <alexl@redhat.com> Signed-off-by: Amir Goldstein <amir73il@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The test on so_count in nfsd4_release_lockowner() is nonsense and
harmful. Revert to using check_for_locks(), changing that to not sleep.
First: harmful.
As is documented in the kdoc comment for nfsd4_release_lockowner(), the
test on so_count can transiently return a false positive resulting in a
return of NFS4ERR_LOCKS_HELD when in fact no locks are held. This is
clearly a protocol violation and with the Linux NFS client it can cause
incorrect behaviour.
If RELEASE_LOCKOWNER is sent while some other thread is still
processing a LOCK request which failed because, at the time that request
was received, the given owner held a conflicting lock, then the nfsd
thread processing that LOCK request can hold a reference (conflock) to
the lock owner that causes nfsd4_release_lockowner() to return an
incorrect error.
The Linux NFS client ignores that NFS4ERR_LOCKS_HELD error because it
never sends NFS4_RELEASE_LOCKOWNER without first releasing any locks, so
it knows that the error is impossible. It assumes the lock owner was in
fact released so it feels free to use the same lock owner identifier in
some later locking request.
When it does reuse a lock owner identifier for which a previous RELEASE
failed, it will naturally use a lock_seqid of zero. However the server,
which didn't release the lock owner, will expect a larger lock_seqid and
so will respond with NFS4ERR_BAD_SEQID.
So clearly it is harmful to allow a false positive, which testing
so_count allows.
The test is nonsense because ... well... it doesn't mean anything.
so_count is the sum of three different counts.
1/ the set of states listed on so_stateids
2/ the set of active vfs locks owned by any of those states
3/ various transient counts such as for conflicting locks.
When it is tested against '2' it is clear that one of these is the
transient reference obtained by find_lockowner_str_locked(). It is not
clear what the other one is expected to be.
In practice, the count is often 2 because there is precisely one state
on so_stateids. If there were more, this would fail.
In my testing I see two circumstances when RELEASE_LOCKOWNER is called.
In one case, CLOSE is called before RELEASE_LOCKOWNER. That results in
all the lock states being removed, and so the lockowner being discarded
(it is removed when there are no more references which usually happens
when the lock state is discarded). When nfsd4_release_lockowner() finds
that the lock owner doesn't exist, it returns success.
The other case shows an so_count of '2' and precisely one state listed
in so_stateid. It appears that the Linux client uses a separate lock
owner for each file resulting in one lock state per lock owner, so this
test on '2' is safe. For another client it might not be safe.
So this patch changes check_for_locks() to use the (newish)
find_any_file_locked() so that it doesn't take a reference on the
nfs4_file and so never calls nfsd_file_put(), and so never sleeps. With
this check is it safe to restore the use of check_for_locks() rather
than testing so_count against the mysterious '2'.
Fixes: ce3c4ad7f4ce ("NFSD: Fix possible sleep during nfsd4_release_lockowner()") Signed-off-by: NeilBrown <neilb@suse.de> Reviewed-by: Jeff Layton <jlayton@kernel.org> Cc: stable@vger.kernel.org # v6.2+ Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
iwl_fw_ini_trigger_tlv::data is a pointer to a __le32, which means that
if we copy to iwl_fw_ini_trigger_tlv::data + offset while offset is in
bytes, we'll write past the buffer.
Cc: stable@vger.kernel.org Closes: https://bugzilla.kernel.org/show_bug.cgi?id=218233 Fixes: cf29c5b66b9f ("iwlwifi: dbg_ini: implement time point handling") Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com> Link: https://msgid.link/20240111150610.2d2b8b870194.I14ed76505a5cf87304e0c9cc05cc0ae85ed3bf91@changeid Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If get_unused_fd_flags() fails, the error handling is incomplete because
bprm->cred is already set to NULL, and therefore free_bprm will not
unlock the cred_guard_mutex. Note there are two error conditions which
end up here, one before and one after bprm->cred is cleared.
The running list is supposed to contain requests that are pinning the
exclusive lock, i.e. those that must be flushed before exclusive lock
is released. When wake_lock_waiters() is called to handle an error,
requests on the acquiring list are failed with that error and no
flushing takes place. Briefly moving them to the running list is not
only pointless but also harmful: if exclusive lock gets acquired
before all of their state machines are scheduled and go through
rbd_lock_del_request(), we trigger
This happens because create_pending_snapshot() initializes the new root
item as a copy of the source root item. This includes the refs field,
which is 0 for a deleted subvolume. The call to btrfs_insert_root()
therefore inserts a root with refs == 0. btrfs_get_new_fs_root() then
finds the root and returns -ENOENT if refs == 0, which causes
create_pending_snapshot() to abort.
Fix it by checking the source root's refs before attempting the
snapshot, but after locking subvol_sem to avoid racing with deletion.
Add extra sanity check for btrfs_ioctl_defrag_range_args::flags.
This is not really to enhance fuzzing tests, but as a preparation for
future expansion on btrfs_ioctl_defrag_range_args.
In the future we're going to add new members, allowing more fine tuning
for btrfs defrag. Without the -ENONOTSUPP error, there would be no way
to detect if the kernel supports those new defrag features.
CC: stable@vger.kernel.org # 4.14+ Reviewed-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: Qu Wenruo <wqu@suse.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There's a warning in btrfs_issue_discard() when the range is not aligned
to 512 bytes, originally added in 4d89d377bbb0 ("btrfs:
btrfs_issue_discard ensure offset/length are aligned to sector
boundaries"). We can't do sub-sector writes anyway so the adjustment is
the only thing that we can do and the warning is unnecessary.
Sweet Tea spotted a race between subvolume deletion and snapshotting
that can result in the root item for the snapshot having the
BTRFS_ROOT_SUBVOL_DEAD flag set. The race is:
This flag is only checked in send and swap activate, which this would
cause to fail mysteriously.
create_snapshot() now checks the root refs to reject a deleted
subvolume, so we can fix this by locking subvol_sem earlier so that the
BTRFS_ROOT_SUBVOL_DEAD flag and the root refs are updated atomically.
The btrfs CI reported a lockdep warning as follows by running generic
generic/129.
WARNING: possible circular locking dependency detected
6.7.0-rc5+ #1 Not tainted
------------------------------------------------------
kworker/u5:5/793427 is trying to acquire lock: ffff88813256d028 (&cache->lock){+.+.}-{2:2}, at: btrfs_zone_finish_one_bg+0x5e/0x130
but task is already holding lock: ffff88810a23a318 (&fs_info->zone_active_bgs_lock){+.+.}-{2:2}, at: btrfs_zone_finish_one_bg+0x34/0x130
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #1 (&fs_info->zone_active_bgs_lock){+.+.}-{2:2}:
...
-> #0 (&cache->lock){+.+.}-{2:2}:
...
This is because we take fs_info->zone_active_bgs_lock after a block_group's
lock in btrfs_zone_activate() while doing the opposite in other places.
Fix the issue by expanding the fs_info->zone_active_bgs_lock's critical
section and taking it before a block_group's lock.
Fixes: a7e1ac7bdc5a ("btrfs: zoned: reserve zones for an active metadata/system block group") CC: stable@vger.kernel.org # 6.6 Signed-off-by: Naohiro Aota <naohiro.aota@wdc.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The fill ring of the XDP socket may contain not enough buffers to
completey fill the RX queue during socket creation. In this case the
flag XDP_RING_NEED_WAKEUP is not set as this flag is only set if the RX
queue is not completely filled during polling.
Set XDP_RING_NEED_WAKEUP flag also if RX queue is not completely filled
during XDP socket creation.
The RX data buffer includes the FCS. The FCS is already stripped for the
normal data path. But for the XDP data path the FCS is included and
acts like additional/useless data.
Remove the FCS from the RX data buffer also for XDP.
When repeatedly changing the interface link speed using the command below:
ethtool -s eth0 speed 100 duplex full
ethtool -s eth0 speed 1000 duplex full
The following errors may sometimes be reported by the ARM SMMU driver:
[ 5395.035364] fec 5b040000.ethernet eth0: Link is Down
[ 5395.039255] arm-smmu 51400000.iommu: Unhandled context fault:
fsr=0x402, iova=0x00000000, fsynr=0x100001, cbfrsynra=0x852, cb=2
[ 5398.108460] fec 5b040000.ethernet eth0: Link is Up - 100Mbps/Full -
flow control off
It is identified that the FEC driver does not properly stop the TX queue
during the link speed transitions, and this results in the invalid virtual
I/O address translations from the SMMU and causes the context faults.
Fixes: dbc64a8ea231 ("net: fec: move calls to quiesce/resume packet processing out of fec_restart()") Signed-off-by: Shenwei Wang <shenwei.wang@nxp.com> Link: https://lore.kernel.org/r/20240123165141.2008104-1-shenwei.wang@nxp.com Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The prio_arp/ns tests hard code the mode to active-backup. At the same
time, The balance-alb/tlb modes do not support arp/ns target. So remove
the prio_arp/ns tests from the loop and only test active-backup mode.
Fixes: 481b56e0391e ("selftests: bonding: re-format bond option tests") Reported-by: Jay Vosburgh <jay.vosburgh@canonical.com> Closes: https://lore.kernel.org/netdev/17415.1705965957@famine/ Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com> Link: https://lore.kernel.org/r/20240123075917.1576360-1-liuhangbin@gmail.com Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
However, when fjes_hw_setup fails, fjes_hw_exit won't be called and thus
all the resources allocated in fjes_hw_setup will be leaked. In this
patch, we free those resources in fjes_hw_setup and prevents such leaks.
Fixes: 2fcbca687702 ("fjes: platform_driver's .probe and .remove routine") Signed-off-by: Zhipeng Lu <alexious@zju.edu.cn> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://lore.kernel.org/r/20240122172445.3841883-1-alexious@zju.edu.cn Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Now that i40e driver correctly sets up frag_size in xdp_rxq_info, let us
make it work for ZC multi-buffer as well. i40e_ring::rx_buf_len for ZC
is being set via xsk_pool_get_rx_frame_size() and this needs to be
propagated up to xdp_rxq_info.
i40e support XDP multi-buffer so it is supposed to use
__xdp_rxq_info_reg() instead of xdp_rxq_info_reg() and set the
frag_size. It can not be simply converted at existing callsite because
rx_buf_len could be un-initialized, so let us register xdp_rxq_info
within i40e_configure_rx_ring(), which happen to be called with already
initialized rx_buf_len value.
Commit 5180ff1364bc ("i40e: use int for i40e_status") converted 'err' to
int, so two variables to deal with return codes are not needed within
i40e_configure_rx_ring(). Remove 'ret' and use 'err' to handle status
from xdp_rxq_info registration.
XSK ZC Rx path calculates the size of data that will be posted to XSK Rx
queue via subtracting xdp_buff::data_end from xdp_buff::data.
In bpf_xdp_frags_increase_tail(), when underlying memory type of
xdp_rxq_info is MEM_TYPE_XSK_BUFF_POOL, add offset to data_end in tail
fragment, so that later on user space will be able to take into account
the amount of bytes added by XDP program.
Now that ice driver correctly sets up frag_size in xdp_rxq_info, let us
make it work for ZC multi-buffer as well. ice_rx_ring::rx_buf_len for ZC
is being set via xsk_pool_get_rx_frame_size() and this needs to be
propagated up to xdp_rxq_info.
Use a bigger hammer and instead of unregistering only xdp_rxq_info's
memory model, unregister it altogether and register it again and have
xdp_rxq_info with correct frag_size value.
Ice and i40e ZC drivers currently set offset of a frag within
skb_shared_info to 0, which is incorrect. xdp_buffs that come from
xsk_buff_pool always have 256 bytes of a headroom, so they need to be
taken into account to retrieve xdp_buff::data via skb_frag_address().
Otherwise, bpf_xdp_frags_increase_tail() would be starting its job from
xdp_buff::data_hard_start which would result in overwriting existing
payload.
xdp_rxq_info struct can be registered by drivers via two functions -
xdp_rxq_info_reg() and __xdp_rxq_info_reg(). The latter one allows
drivers that support XDP multi-buffer to set up xdp_rxq_info::frag_size
which in turn will make it possible to grow the packet via
bpf_xdp_adjust_tail() BPF helper.
Currently, ice registers xdp_rxq_info in two spots:
1) ice_setup_rx_ring() // via xdp_rxq_info_reg(), BUG
2) ice_vsi_cfg_rxq() // via __xdp_rxq_info_reg(), OK
Cited commit under fixes tag took care of setting up frag_size and
updated registration scheme in 2) but it did not help as
1) is called before 2) and as shown above it uses old registration
function. This means that 2) sees that xdp_rxq_info is already
registered and never calls __xdp_rxq_info_reg() which leaves us with
xdp_rxq_info::frag_size being set to 0.
To fix this misbehavior, simply remove xdp_rxq_info_reg() call from
ice_setup_rx_ring().
Fixes: 2fba7dc5157b ("ice: Add support for XDP multi-buffer on Rx side") Acked-by: Magnus Karlsson <magnus.karlsson@intel.com> Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com> Link: https://lore.kernel.org/r/20240124191602.566724-7-maciej.fijalkowski@intel.com Signed-off-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
XDP programs can shrink packets by calling the bpf_xdp_adjust_tail()
helper function. For multi-buffer packets this may lead to reduction of
frag count stored in skb_shared_info area of the xdp_buff struct. This
results in issues with the current handling of XDP_PASS and XDP_DROP
cases.
For XDP_PASS, currently skb is being built using frag count of
xdp_buffer before it was processed by XDP prog and thus will result in
an inconsistent skb when frag count gets reduced by XDP prog. To fix
this, get correct frag count while building the skb instead of using
pre-obtained frag count.
For XDP_DROP, current page recycling logic will not reuse the page but
instead will adjust the pagecnt_bias so that the page can be freed. This
again results in inconsistent behavior as the page refcnt has already
been changed by the helper while freeing the frag(s) as part of
shrinking the packet. To fix this, only adjust pagecnt_bias for buffers
that are stillpart of the packet post-xdp prog run.
Fixes: e213ced19bef ("i40e: add support for XDP multi-buffer Rx") Reported-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com> Signed-off-by: Tirthendu Sarkar <tirthendu.sarkar@intel.com> Link: https://lore.kernel.org/r/20240124191602.566724-6-maciej.fijalkowski@intel.com Signed-off-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fix an OOM panic in XDP_DRV mode when a XDP program shrinks a
multi-buffer packet by 4k bytes and then redirects it to an AF_XDP
socket.
Since support for handling multi-buffer frames was added to XDP, usage
of bpf_xdp_adjust_tail() helper within XDP program can free the page
that given fragment occupies and in turn decrease the fragment count
within skb_shared_info that is embedded in xdp_buff struct. In current
ice driver codebase, it can become problematic when page recycling logic
decides not to reuse the page. In such case, __page_frag_cache_drain()
is used with ice_rx_buf::pagecnt_bias that was not adjusted after
refcount of page was changed by XDP prog which in turn does not drain
the refcount to 0 and page is never freed.
To address this, let us store the count of frags before the XDP program
was executed on Rx ring struct. This will be used to compare with
current frag count from skb_shared_info embedded in xdp_buff. A smaller
value in the latter indicates that XDP prog freed frag(s). Then, for
given delta decrement pagecnt_bias for XDP_DROP verdict.
While at it, let us also handle the EOP frag within
ice_set_rx_bufs_act() to make our life easier, so all of the adjustments
needed to be applied against freed frags are performed in the single
place.
Fixes: 2fba7dc5157b ("ice: Add support for XDP multi-buffer on Rx side") Acked-by: Magnus Karlsson <magnus.karlsson@intel.com> Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com> Link: https://lore.kernel.org/r/20240124191602.566724-5-maciej.fijalkowski@intel.com Signed-off-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
This comes from __xdp_return() call with xdp_buff argument passed as
NULL which is supposed to be consumed by xsk_buff_free() call.
To address this properly, in ZC case, a node that represents the frag
being removed has to be pulled out of xskb_list. Introduce
appropriate xsk helpers to do such node operation and use them
accordingly within bpf_xdp_adjust_tail().
Fixes: 24ea50127ecf ("xsk: support mbuf on ZC RX") Acked-by: Magnus Karlsson <magnus.karlsson@intel.com> # For the xsk header part Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com> Link: https://lore.kernel.org/r/20240124191602.566724-4-maciej.fijalkowski@intel.com Signed-off-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
XDP multi-buffer support introduced XDP_FLAGS_HAS_FRAGS flag that is
used by drivers to notify data path whether xdp_buff contains fragments
or not. Data path looks up mentioned flag on first buffer that occupies
the linear part of xdp_buff, so drivers only modify it there. This is
sufficient for SKB and XDP_DRV modes as usually xdp_buff is allocated on
stack or it resides within struct representing driver's queue and
fragments are carried via skb_frag_t structs. IOW, we are dealing with
only one xdp_buff.
ZC mode though relies on list of xdp_buff structs that is carried via
xsk_buff_pool::xskb_list, so ZC data path has to make sure that
fragments do *not* have XDP_FLAGS_HAS_FRAGS set. Otherwise,
xsk_buff_free() could misbehave if it would be executed against xdp_buff
that carries a frag with XDP_FLAGS_HAS_FRAGS flag set. Such scenario can
take place when within supplied XDP program bpf_xdp_adjust_tail() is
used with negative offset that would in turn release the tail fragment
from multi-buffer frame.
Calling xsk_buff_free() on tail fragment with XDP_FLAGS_HAS_FRAGS would
result in releasing all the nodes from xskb_list that were produced by
driver before XDP program execution, which is not what is intended -
only tail fragment should be deleted from xskb_list and then it should
be put onto xsk_buff_pool::free_list. Such multi-buffer frame will never
make it up to user space, so from AF_XDP application POV there would be
no traffic running, however due to free_list getting constantly new
nodes, driver will be able to feed HW Rx queue with recycled buffers.
Bottom line is that instead of traffic being redirected to user space,
it would be continuously dropped.
To fix this, let us clear the mentioned flag on xsk_buff_pool side
during xdp_buff initialization, which is what should have been done
right from the start of XSK multi-buffer support.
This test is missing a whole bunch of checks for interface
renaming and one ifup. Presumably it was only used on a system
with renaming disabled and NetworkManager running.
Fixes: 91f430b2c49d ("selftests: net: add a test for UDP tunnel info infra") Acked-by: Paolo Abeni <pabeni@redhat.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://lore.kernel.org/r/20240123060529.1033912-1-kuba@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
If there is more than 32 cpus the bitmask will start to contain
commas, leading to:
./rps_default_mask.sh: line 36: [: 00000000,00000000: integer expression expected
Remove the commas, bash doesn't interpret leading zeroes as oct
so that should be good enough. Switch to bash, Simon reports that
not all shells support this type of substitution.
Fixes: c12e0d5f267d ("self-tests: introduce self-tests for RPS default mask") Reviewed-by: Simon Horman <horms@kernel.org> Link: https://lore.kernel.org/r/20240122195815.638997-1-kuba@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Register value persist after booting the kernel using
kexec which results in kernel panic. Thus clear the
BM pool registers before initialisation to fix the issue.
Fixes: 3f518509dedc ("ethernet: Add new driver for Marvell Armada 375 network unit") Signed-off-by: Jenishkumar Maheshbhai Patel <jpatel2@marvell.com> Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com> Link: https://lore.kernel.org/r/20240119035914.2595665-1-jpatel2@marvell.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
otherwise the synopsys_id value may be read out wrong,
because the GMAC_VERSION register might still be in reset
state, for at least 1 us after the reset is de-asserted.
Add a wait for 10 us before continuing to be on the safe side.
> From what have you got that delay value?
Just try and error, with very old linux versions and old gcc versions
the synopsys_id was read out correctly most of the time (but not always),
with recent linux versions and recnet gcc versions it was read out
wrongly most of the time, but again not always.
I don't have access to the VHDL code in question, so I cannot
tell why it takes so long to get the correct values, I also do not
have more than a few hardware samples, so I cannot tell how long
this timeout must be in worst case.
Experimentally I can tell that the register is read several times
as zero immediately after the reset is de-asserted, also adding several
no-ops is not enough, adding a printk is enough, also udelay(1) seems to
be enough but I tried that not very often, and I have not access to many
hardware samples to be 100% sure about the necessary delay.
And since the udelay here is only executed once per device instance,
it seems acceptable to delay the boot for 10 us.
nftables has two types of sets/maps, one where userspace defines the
name, and anonymous sets/maps, where userspace defines a template name.
For the latter, kernel requires presence of exactly one "%d".
nftables uses "__set%d" and "__map%d" for this. The kernel will
expand the format specifier and replaces it with the smallest unused
number.
As-is, userspace could define a template name that allows to move
the set name past the 256 bytes upperlimit (post-expansion).
I don't see how this could be a problem, but I would prefer if userspace
cannot do this, so add a limit of 16 bytes for the '%d' template name.
16 bytes is the old total upper limit for set names that existed when
nf_tables was merged initially.
Fixes: 387454901bd6 ("netfilter: nf_tables: Allow set names of up to 255 chars") Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When the CPU goes idle for the last time during the CPU down hotplug
process, RCU reports a final quiescent state for the current CPU. If
this quiescent state propagates up to the top, some tasks may then be
woken up to complete the grace period: the main grace period kthread
and/or the expedited main workqueue (or kworker).
If those kthreads have a SCHED_FIFO policy, the wake up can indirectly
arm the RT bandwith timer to the local offline CPU. Since this happens
after hrtimers have been migrated at CPUHP_AP_HRTIMERS_DYING stage, the
timer gets ignored. Therefore if the RCU kthreads are waiting for RT
bandwidth to be available, they may never be actually scheduled.
The situation can't be solved with just unpinning the timer. The hrtimer
infrastructure and the nohz heuristics involved in finding the best
remote target for an unpinned timer would then also need to handle
enqueues from an offline CPU in the most horrendous way.
So fix this on the RCU side instead and defer the wake up to an online
CPU if it's too late for the local one.
Reported-by: Paul E. McKenney <paulmck@kernel.org> Fixes: 5c0930ccaad5 ("hrtimers: Push pending hrtimers away from outgoing CPU earlier") Signed-off-by: Frederic Weisbecker <frederic@kernel.org> Signed-off-by: Paul E. McKenney <paulmck@kernel.org> Signed-off-by: Neeraj Upadhyay (AMD) <neeraj.iitr10@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When kcalloc() for ft->g succeeds but kvzalloc() for in fails,
fs_any_create_groups() will free ft->g. However, its caller
fs_any_create_table() will free ft->g again through calling
mlx5e_destroy_flow_table(), which will lead to a double-free.
Fix this by setting ft->g to NULL in fs_any_create_groups().
Fixes: 0f575c20bf06 ("net/mlx5e: Introduce Flow Steering ANY API") Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn> Reviewed-by: Tariq Toukan <tariqt@nvidia.com> Reviewed-by: Simon Horman <horms@kernel.org> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When `in` allocated by kvzalloc fails, arfs_create_groups will free
ft->g and return an error. However, arfs_create_table, the only caller of
arfs_create_groups, will hold this error and call to
mlx5e_destroy_flow_table, in which the ft->g will be freed again.
XFRM stack doesn't prevent from users to configure replay window
in TX side and strongswan sets replay_window to be 1. It causes
to failures in validation logic when trying to offload the SA.
Replay window is not relevant in TX side and should be ignored.
Fixes: cded6d80129b ("net/mlx5e: Store replay window in XFRM attributes") Signed-off-by: Aya Levin <ayal@nvidia.com> Signed-off-by: Leon Romanovsky <leonro@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
All ConnectX devices have software parsing capability enabled, but it is
more correct to set allow_swp only if capability exists, which for IPsec
means that crypto offload is supported.
mlx5 devices have specific constants for choosing the CQ period mode. These
constants do not have to match the constants used by the kernel software
API for DIM period mode selection.
Fixes: cdd04f4d4d71 ("net/mlx5: Add support to create SQ and CQ for ASO") Signed-off-by: Rahul Rameshbabu <rrameshbabu@nvidia.com> Reviewed-by: Jianbo Liu <jianbol@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When FW provides ICM addresses for drop RX/TX, the provided capability
is 64 bits that contain its GVMI as well as the ICM address itself.
In case of TX DROP this GVMI is different from the GVMI that the
domain is operating on.
This patch fixes the action to use these GVMI IDs, as provided by FW.
To enable multicast packets which are offloaded in bridge multicast
offload mode to be sent also to uplink, FTE bit uplink_hairpin_en should
be set. Add this bit to FTE for the bridge multicast offload rules.
The cited change refactored mlx5e_tc_del_fdb_peer_flow() to only clear DUP
flag when list of peer flows has become empty. However, if any concurrent
user holds a reference to a peer flow (for example, the neighbor update
workqueue task is updating peer flow's parent encap entry concurrently),
then the flow will not be removed from the peer list and, consecutively,
DUP flag will remain set. Since mlx5e_tc_del_fdb_peers_flow() calls
mlx5e_tc_del_fdb_peer_flow() for every possible peer index the algorithm
will try to remove the flow from eswitch instances that it has never peered
with causing either NULL pointer dereference when trying to remove the flow
peer list head of peer_index that was never initialized or a warning if the
list debug config is enabled[0].
Fix the issue by always removing the peer flow from the list even when not
releasing the last reference to it.
The processing of traffic in hairpin queues occurs in HW/FW and does not
involve the cpus, hence the upper bound on max num channels does not
apply to them. Using this bound for the hairpin RQT max_table_size is
wrong. It could be too small, and cause the error below [1]. As the
RQT size provided on init does not get modified later, use the same
value for both actual and max table sizes.
[1]
mlx5_core 0000:08:00.1: mlx5_cmd_out_err:805:(pid 1200): CREATE_RQT(0x916) op_mod(0x0) failed, status bad parameter(0x3), syndrome (0x538faf), err(-22)
Fixes: 74a8dadac17e ("net/mlx5e: Preparations for supporting larger number of channels") Signed-off-by: Tariq Toukan <tariqt@nvidia.com> Reviewed-by: Gal Pressman <gal@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Indirection (*) is of lower precedence than postfix increment (++). Logic
in napi_poll context would cause an out-of-bound read by first increment
the pointer address by byte address space and then dereference the value.
Rather, the intended logic was to dereference first and then increment the
underlying value.
Fixes: 92214be5979c ("net/mlx5e: Update doorbell for port timestamping CQ before the software counter") Signed-off-by: Rahul Rameshbabu <rrameshbabu@nvidia.com> Reviewed-by: Tariq Toukan <tariqt@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When a qdisc is deleted from a net device the stack instructs the
underlying driver to remove its flow offload callback from the
associated filter block using the 'FLOW_BLOCK_UNBIND' command. The stack
then continues to replay the removal of the filters in the block for
this driver by iterating over the chains in the block and invoking the
'reoffload' operation of the classifier being used. In turn, the
classifier in its 'reoffload' operation prepares and emits a
'FLOW_CLS_DESTROY' command for each filter.
However, the stack does not do the same for chain templates and the
underlying driver never receives a 'FLOW_CLS_TMPLT_DESTROY' command when
a qdisc is deleted. This results in a memory leak [1] which can be
reproduced using [2].
Fix by introducing a 'tmplt_reoffload' operation and have the stack
invoke it with the appropriate arguments as part of the replay.
Implement the operation in the sole classifier that supports chain
templates (flower) by emitting the 'FLOW_CLS_TMPLT_{CREATE,DESTROY}'
command based on whether a flow offload callback is being bound to a
filter block or being unbound from one.
As far as I can tell, the issue happens since cited commit which
reordered tcf_block_offload_unbind() before tcf_block_flush_all_chains()
in __tcf_block_put(). The order cannot be reversed as the filter block
is expected to be freed after flushing all the chains.
[2]
# tc qdisc add dev swp1 clsact
# tc chain add dev swp1 ingress proto ip chain 1 flower dst_ip 0.0.0.0/32
# tc qdisc del dev swp1 clsact
# devlink dev reload pci/0000:06:00.0
Fixes: bbf73830cd48 ("net: sched: traverse chains in block with tcf_get_next_chain()") Signed-off-by: Ido Schimmel <idosch@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
I analyze the potential sleeping issue of the following processes:
Thread A Thread B
... netlink_create //ref = 1
do_mq_notify ...
sock = netlink_getsockbyfilp ... //ref = 2
info->notify_sock = sock; ...
... netlink_sendmsg
... skb = netlink_alloc_large_skb //skb->head is vmalloced
... netlink_unicast
... sk = netlink_getsockbyportid //ref = 3
... netlink_sendskb
... __netlink_sendskb
... skb_queue_tail //put skb to sk_receive_queue
... sock_put //ref = 2
... ...
... netlink_release
... deferred_put_nlk_sk //ref = 1
mqueue_flush_file
spin_lock
remove_notification
netlink_sendskb
sock_put //ref = 0
sk_free
...
__sk_destruct
netlink_sock_destruct
skb_queue_purge //get skb from sk_receive_queue
...
__skb_queue_purge_reason
kfree_skb_reason
__kfree_skb
...
skb_release_all
skb_release_head_state
netlink_skb_destructor
vfree(skb->head) //sleeping while holding spinlock
In netlink_sendmsg, if the memory pointed to by skb->head is allocated by
vmalloc, and is put to sk_receive_queue queue, also the skb is not freed.
When the mqueue executes flush, the sleeping bug will occur. Use
vfree_atomic instead of vfree in netlink_skb_destructor to solve the issue.
Fixes: c05cdb1b864f ("netlink: allow large data transfers from user-space") Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com> Link: https://lore.kernel.org/r/20240122011807.2110357-1-shaozhengchao@huawei.com Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Jakub reported that ASSERT_EQ(cpu, i) in so_incoming_cpu.c seems to
fire somewhat randomly.
# # RUN so_incoming_cpu.before_reuseport.test3 ...
# # so_incoming_cpu.c:191:test3:Expected cpu (32) == i (0)
# # test3: Test terminated by assertion
# # FAIL so_incoming_cpu.before_reuseport.test3
# not ok 3 so_incoming_cpu.before_reuseport.test3
When the test failed, not-yet-accepted CLOSE_WAIT sockets received
SYN with a "challenging" SEQ number, which was sent from an unexpected
CPU that did not create the receiver.
The test basically does:
1. for each cpu:
1-1. create a server
1-2. set SO_INCOMING_CPU
2. for each cpu:
2-1. set cpu affinity
2-2. create some clients
2-3. let clients connect() to the server on the same cpu
2-4. close() clients
3. for each server:
3-1. accept() all child sockets
3-2. check if all children have the same SO_INCOMING_CPU with the server
The root cause was the close() in 2-4. and net.ipv4.tcp_tw_reuse.
In a loop of 2., close() changed the client state to FIN_WAIT_2, and
the peer transitioned to CLOSE_WAIT.
In another loop of 2., connect() happened to select the same port of
the FIN_WAIT_2 socket, and it was reused as the default value of
net.ipv4.tcp_tw_reuse is 2.
As a result, the new client sent SYN to the CLOSE_WAIT socket from
a different CPU, and the receiver's sk_incoming_cpu was overwritten
with unexpected CPU ID.
Also, the SYN had a different SEQ number, so the CLOSE_WAIT socket
responded with Challenge ACK. The new client properly returned RST
and effectively killed the CLOSE_WAIT socket.
This way, all clients were created successfully, but the error was
detected later by 3-2., ASSERT_EQ(cpu, i).
To avoid the failure, let's make sure that (i) the number of clients
is less than the number of available ports and (ii) such reuse never
happens.
Fixes: 6df96146b202 ("selftest: Add test for SO_INCOMING_CPU.") Reported-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com> Tested-by: Jakub Kicinski <kuba@kernel.org> Link: https://lore.kernel.org/r/20240120031642.67014-1-kuniyu@amazon.com Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
On CPUs with weak memory models, reads and updates performed by tcp_push
to the sk variables can get reordered leaving the socket throttled when
it should not. The tasklet running tcp_wfree() may also not observe the
memory updates in time and will skip flushing any packets throttled by
tcp_push(), delaying the sending. This can pathologically cause 40ms
extra latency due to bad interactions with delayed acks.
Adding a memory barrier in tcp_push removes the bug, similarly to the
previous commit bf06200e732d ("tcp: tsq: fix nonagle handling").
smp_mb__after_atomic() is used to not incur in unnecessary overhead
on x86 since not affected.
Patch has been tested using an AWS c7g.2xlarge instance with Ubuntu
22.04 and Apache Tomcat 9.0.83 running the basic servlet below:
public class HelloWorldServlet extends HttpServlet {
@Override
protected void doGet(HttpServletRequest request, HttpServletResponse response)
throws ServletException, IOException {
response.setContentType("text/html;charset=utf-8");
OutputStreamWriter osw = new OutputStreamWriter(response.getOutputStream(),"UTF-8");
String s = "a".repeat(3096);
osw.write(s,0,s.length());
osw.flush();
}
}
Load was applied using wrk2 (https://github.com/kinvolk/wrk2) from an AWS
c6i.8xlarge instance. Before the patch an additional 40ms latency from P99.99+
values is observed while, with the patch, the extra latency disappears.
No patch and tcp_autocorking=1
./wrk -t32 -c128 -d40s --latency -R10000 http://172.31.60.173:8080/hello/hello
...
50.000% 0.91ms
75.000% 1.13ms
90.000% 1.46ms
99.000% 1.74ms
99.900% 1.89ms
99.990% 41.95ms <<< 40+ ms extra latency
99.999% 48.32ms
100.000% 48.96ms
With patch and tcp_autocorking=1
./wrk -t32 -c128 -d40s --latency -R10000 http://172.31.60.173:8080/hello/hello
...
50.000% 0.90ms
75.000% 1.13ms
90.000% 1.45ms
99.000% 1.72ms
99.900% 1.83ms
99.990% 2.11ms <<< no 40+ ms extra latency
99.999% 2.53ms
100.000% 2.62ms
Patch has been also tested on x86 (m7i.2xlarge instance) which it is not
affected by this issue and the patch doesn't introduce any additional
delay.
Fixes: 7aa5470c2c09 ("tcp: tsq: move tsq_flags close to sk_wmem_alloc") Signed-off-by: Salvatore Dipietro <dipiets@amazon.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Link: https://lore.kernel.org/r/20240119190133.43698-1-dipiets@amazon.com Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When afs does a lookup, it tries to use FS.InlineBulkStatus to preemptively
look up a bunch of files in the parent directory and cache this locally, on
the basis that we might want to look at them too (for example if someone
does an ls on a directory, they may want want to then stat every file
listed).
FS.InlineBulkStatus can be considered a compound op with the normal abort
code applying to the compound as a whole. Each status fetch within the
compound is then given its own individual abort code - but assuming no
error that prevents the bulk fetch from returning the compound result will
be 0, even if all the constituent status fetches failed.
At the conclusion of afs_do_lookup(), we should use the abort code from the
appropriate status to determine the error to return, if any - but instead
it is assumed that we were successful if the op as a whole succeeded and we
return an incompletely initialised inode, resulting in ENOENT, no matter
the actual reason. In the particular instance reported, a vnode with no
permission granted to be accessed is being given a UAEACCES abort code
which should be reported as EACCES, but is instead being reported as
ENOENT.
Fix this by abandoning the inode (which will be cleaned up with the op) if
file[1] has an abort code indicated and turn that abort code into an error
instead.
Whilst we're at it, add a tracepoint so that the abort codes of the
individual subrequests of FS.InlineBulkStatus can be logged. At the moment
only the container abort code can be 0.
Fixes: e49c7b2f6de7 ("afs: Build an abstraction around an "operation" concept") Reported-by: Jeffrey Altman <jaltman@auristor.com> Signed-off-by: David Howells <dhowells@redhat.com> Reviewed-by: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org Signed-off-by: Sasha Levin <sashal@kernel.org>
Simplify error handling a bit by moving it from the afs_addr_cursor struct
to the afs_operation and afs_vl_cursor structs and using the error
prioritisation function for accumulating errors from multiple sources (AFS
tries to rotate between multiple fileservers, some of which may be
inaccessible or in some state of offlinedness).
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
Stable-dep-of: 17ba6f0bd14f ("afs: Fix error handling with lookup via FS.InlineBulkStatus") Signed-off-by: Sasha Levin <sashal@kernel.org>
Don't put the afs_call struct in afs_wait_for_call_to_complete() but rather
have the caller do it. This will allow the caller to fish stuff out of the
afs_call struct rather than the afs_addr_cursor struct, thereby allowing a
subsequent patch to subsume it.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
Stable-dep-of: 17ba6f0bd14f ("afs: Fix error handling with lookup via FS.InlineBulkStatus") Signed-off-by: Sasha Levin <sashal@kernel.org>
Wrap most op->error accesses with inline funcs which will make it easier
for a subsequent patch to replace op->error with something else. Two
functions are added to this end:
(1) afs_op_error() - Get the error code.
(2) afs_op_set_error() - Set the error code.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
Stable-dep-of: 17ba6f0bd14f ("afs: Fix error handling with lookup via FS.InlineBulkStatus") Signed-off-by: Sasha Levin <sashal@kernel.org>
Set op->nr_iterations to -1 to indicate that we need to begin fileserver
iteration rather than setting error to SHRT_MAX. This makes it easier to
eliminate the address cursor.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
Stable-dep-of: 17ba6f0bd14f ("afs: Fix error handling with lookup via FS.InlineBulkStatus") Signed-off-by: Sasha Levin <sashal@kernel.org>
When processing the result of a call, handle the VIO and UAEIO abort
specifically rather than leaving it to a default case. Rather than
erroring out unconditionally, see if there's another server if the volume
has more than one server available, otherwise return -EREMOTEIO.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
Stable-dep-of: 17ba6f0bd14f ("afs: Fix error handling with lookup via FS.InlineBulkStatus") Signed-off-by: Sasha Levin <sashal@kernel.org>
(1) A new function, rxrpc_kernel_lookup_peer(), is provided to look up an
rxrpc_peer record for a remote address and a corresponding function,
rxrpc_kernel_put_peer(), is provided to dispose of it again.
(2) When setting up a call, the rxrpc_peer object used during a call is
now passed in rather than being set up by rxrpc_connect_call(). For
afs, this meenat passing it to rxrpc_kernel_begin_call() rather than
the full address (the service ID then has to be passed in as a
separate parameter).
(3) A new function, rxrpc_kernel_remote_addr(), is added so that afs can
get a pointer to the transport address for display purposed, and
another, rxrpc_kernel_remote_srx(), to gain a pointer to the full
rxrpc address.
(4) The function to retrieve the RTT from a call, rxrpc_kernel_get_srtt(),
is then altered to take a peer. This now returns the RTT or -1 if
there are insufficient samples.
(5) Rename rxrpc_kernel_get_peer() to rxrpc_kernel_call_get_peer().
(6) Provide a new function, rxrpc_kernel_get_peer(), to get a ref on a
peer the caller already has.
This allows the afs filesystem to pin the rxrpc_peer records that it is
using, allowing faster lookups and pointer comparisons rather than
comparing sockaddr_rxrpc contents. It also makes it easier to get hold of
the RTT. The following changes are made to afs:
(1) The addr_list struct's addrs[] elements now hold a peer struct pointer
and a service ID rather than a sockaddr_rxrpc.
(2) When displaying the transport address, rxrpc_kernel_remote_addr() is
used.
(3) The port arg is removed from afs_alloc_addrlist() since it's always
overridden.
(4) afs_merge_fs_addr4() and afs_merge_fs_addr6() do peer lookup and may
now return an error that must be handled.
(5) afs_find_server() now takes a peer pointer to specify the address.
(6) afs_find_server(), afs_compare_fs_alists() and afs_merge_fs_addr[46]{}
now do peer pointer comparison rather than address comparison.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
Stable-dep-of: 17ba6f0bd14f ("afs: Fix error handling with lookup via FS.InlineBulkStatus") Signed-off-by: Sasha Levin <sashal@kernel.org>
There could be a lot of servers in the list and each server can have
multiple addresses, so I think this would be better with an exclusive
second pass.
The server list isn't likely to change all that often, but when it does
change, there's a good chance several servers are going to be
added/removed one after the other. Further, this is only going to be
used for incoming cache management/callback requests from the server,
which hopefully aren't going to happen too often - but it is remotely
drivable.
(6) afs_find_server_by_uuid().
Similarly to (5), there could be a lot of servers to search through, but
they are in a tree not a flat list, so it should be faster to process.
Again, it's not likely to change that often and, again, when it does
change it's likely to involve multiple changes. This can be driven
remotely by an incoming cache management request but is mostly going to
be driven by setting up or reconfiguring a volume's server list -
something that also isn't likely to happen often.
Make the "seq" counter odd on the 2nd pass, otherwise read_seqbegin_or_lock()
never takes the lock.
Signed-off-by: Oleg Nesterov <oleg@redhat.com> Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org Link: https://lore.kernel.org/r/20231130115614.GA21581@redhat.com/
Stable-dep-of: 17ba6f0bd14f ("afs: Fix error handling with lookup via FS.InlineBulkStatus") Signed-off-by: Sasha Levin <sashal@kernel.org>
There appears to be a race between silly-rename files being created/removed
and various userspace tools iterating over the contents of a directory,
leading to such errors as:
find: './kernel/.tmp_cpio_dir/include/dt-bindings/reset/.__afs2080': No such file or directory
tar: ./include/linux/greybus/.__afs3C95: File removed before we read it
when building a kernel.
Fix afs_readdir() so that it doesn't return .__afsXXXX silly-rename files
to userspace. This doesn't stop them being looked up directly by name as
we need to be able to look them up from within the kernel as part of the
silly-rename algorithm.
Fixes: 79ddbfa500b3 ("afs: Implement sillyrename for unlink and rename") Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org Signed-off-by: Sasha Levin <sashal@kernel.org>
Running the following two commands in parallel on a multi-processor
AArch64 machine can sporadically produce an unexpected warning about
duplicate histogram entries:
$ while true; do
echo hist:key=id.syscall:val=hitcount > \
/sys/kernel/debug/tracing/events/raw_syscalls/sys_enter/trigger
cat /sys/kernel/debug/tracing/events/raw_syscalls/sys_enter/hist
sleep 0.001
done
$ stress-ng --sysbadaddr $(nproc)
The "memcpy(elt->key, key, map->key_size);" and "entry->val = elt;"
stores may become visible in the reversed order on another CPU. This
second CPU might then incorrectly determine that a new key doesn't match
an already present val->key and subsequently insert a new element,
resulting in a duplicate.
Fix the problem by adding a write barrier between
"memcpy(elt->key, key, map->key_size);" and "entry->val = elt;", and for
good measure, also use WRITE_ONCE(entry->val, elt) for publishing the
element. The sequence pairs with the mentioned "READ_ONCE(entry->val);"
and the "val->key" check which has an address dependency.
The barrier is placed on a path executed when adding an element for
a new key. Subsequent updates targeting the same key remain unaffected.
From the user's perspective, the issue was introduced by commit c193707dde77 ("tracing: Remove code which merges duplicates"), which
followed commit cbf4100efb8f ("tracing: Add support to detect and avoid
duplicates"). The previous code operated differently; it inherently
expected potential races which result in duplicates but merged them
later when they occurred.
Link: https://lore.kernel.org/linux-trace-kernel/20240122150928.27725-1-petr.pavlu@suse.com Fixes: c193707dde77 ("tracing: Remove code which merges duplicates") Signed-off-by: Petr Pavlu <petr.pavlu@suse.com> Acked-by: Tom Zanussi <tom.zanussi@linux.intel.com> Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Syzcaller UBSAN crash occurs in rds_cmsg_recv(),
which reads inc->i_rx_lat_trace[j + 1] with index 4 (3 + 1),
but with array size of 4 (RDS_RX_MAX_TRACES).
Here 'j' is assigned from rs->rs_rx_trace[i] and in-turn from
trace.rx_trace_pos[i] in rds_recv_track_latency(),
with both arrays sized 3 (RDS_MSG_RX_DGRAM_TRACE_MAX). So fix the
off-by-one bounds check in rds_recv_track_latency() to prevent
a potential crash in rds_cmsg_recv().
Found by syzcaller:
=================================================================
UBSAN: array-index-out-of-bounds in net/rds/recv.c:585:39
index 4 is out of range for type 'u64 [4]'
CPU: 1 PID: 8058 Comm: syz-executor228 Not tainted 6.6.0-gd2f51b3516da #1
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996),
BIOS 1.15.0-1 04/01/2014
Call Trace:
<TASK>
__dump_stack lib/dump_stack.c:88 [inline]
dump_stack_lvl+0x136/0x150 lib/dump_stack.c:106
ubsan_epilogue lib/ubsan.c:217 [inline]
__ubsan_handle_out_of_bounds+0xd5/0x130 lib/ubsan.c:348
rds_cmsg_recv+0x60d/0x700 net/rds/recv.c:585
rds_recvmsg+0x3fb/0x1610 net/rds/recv.c:716
sock_recvmsg_nosec net/socket.c:1044 [inline]
sock_recvmsg+0xe2/0x160 net/socket.c:1066
__sys_recvfrom+0x1b6/0x2f0 net/socket.c:2246
__do_sys_recvfrom net/socket.c:2264 [inline]
__se_sys_recvfrom net/socket.c:2260 [inline]
__x64_sys_recvfrom+0xe0/0x1b0 net/socket.c:2260
do_syscall_x64 arch/x86/entry/common.c:51 [inline]
do_syscall_64+0x40/0x110 arch/x86/entry/common.c:82
entry_SYSCALL_64_after_hwframe+0x63/0x6b
==================================================================
Fixes: 3289025aedc0 ("RDS: add receive message trace used by application") Reported-by: Chenyuan Yang <chenyuan0y@gmail.com> Closes: https://lore.kernel.org/linux-rdma/CALGdzuoVdq-wtQ4Az9iottBqC5cv9ZhcE5q8N7LfYFvkRsOVcw@mail.gmail.com/ Signed-off-by: Sharath Srinivasan <sharath.srinivasan@oracle.com> Reviewed-by: Simon Horman <horms@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The HW has the capability to check each frame if it is a PTP frame,
which domain it is, which ptp frame type it is, different ip address in
the frame. And if one of these checks fail then the frame is not
timestamp. Most of these checks were disabled except checking the field
minorVersionPTP inside the PTP header. Meaning that once a partner sends
a frame compliant to 8021AS which has minorVersionPTP set to 1, then the
frame was not timestamp because the HW expected by default a value of 0
in minorVersionPTP. This is exactly the same issue as on lan8841.
Fix this issue by removing this check so the userspace can decide on this.
Fixes: ece19502834d ("net: phy: micrel: 1588 support for LAN8814 phy") Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com> Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com> Reviewed-by: Divya Koppera <divya.koppera@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
In case of multiple kernel module instances using the same dpll device:
if only one registers dpll device, then only that one can register
directly connected pins with a dpll device. When unregistered parent is
responsible for determining if the muxed pin can be registered with it
or not, the drivers need to be loaded in serialized order to work
correctly - first the driver instance which registers the direct pins
needs to be loaded, then the other instances could register muxed type
pins.
Allow registration of a pin with a parent even if the parent was not
yet registered, thus allow ability for unserialized driver instance
load order.
Do not WARN_ON notification for unregistered pin, which can be invoked
for described case, instead just return error.
Fixes: 9431063ad323 ("dpll: core: Add DPLL framework base functions") Fixes: 9d71b54b65b1 ("dpll: netlink: Add DPLL framework base functions") Reviewed-by: Jan Glaza <jan.glaza@intel.com> Reviewed-by: Jiri Pirko <jiri@nvidia.com> Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
If parent pin was unregistered but child pin was not, the userspace
would see the "zombie" pins - the ones that were registered with
a parent pin (dpll_pin_on_pin_register(..)).
Technically those are not available - as there is no dpll device in the
system. Do not dump those pins and prevent userspace from any
interaction with them. Provide a unified function to determine if the
pin is available and use it before acting/responding for user requests.
Fixes: 9d71b54b65b1 ("dpll: netlink: Add DPLL framework base functions") Reviewed-by: Jan Glaza <jan.glaza@intel.com> Reviewed-by: Jiri Pirko <jiri@nvidia.com> Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
When a kernel module is unbound but the pin resources were not entirely
freed (other kernel module instance of the same PCI device have had kept
the reference to that pin), and kernel module is again bound, the pin
properties would not be updated (the properties are only assigned when
memory for the pin is allocated), prop pointer still points to the
kernel module memory of the kernel module which was deallocated on the
unbind.
If the pin dump is invoked in this state, the result is a kernel crash.
Prevent the crash by storing persistent pin properties in dpll subsystem,
copy the content from the kernel module when pin is allocated, instead of
using memory of the kernel module.
Fixes: 9431063ad323 ("dpll: core: Add DPLL framework base functions") Fixes: 9d71b54b65b1 ("dpll: netlink: Add DPLL framework base functions") Reviewed-by: Jan Glaza <jan.glaza@intel.com> Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com> Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com> Reviewed-by: Jiri Pirko <jiri@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
If pin type is not expected, or pin properities failed to allocate
memory, the unwind error path shall not destroy pin's xarrays, which
were not yet initialized.
Add new goto label and use it to fix broken error path.
Reviewed-by: Jiri Pirko <jiri@nvidia.com> Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: 830ead5fb0c5 ("dpll: fix pin dump crash for rebound module") Signed-off-by: Sasha Levin <sashal@kernel.org>
The TUN can be used as vhost-net backend, and it is necessary to
count the packets transmitted from TUN to vhost-net/virtio-net.
However, there are some places in the receive path that were not
taken into account when using XDP. It would be beneficial to also
include new accounting for successfully received bytes using
dev_sw_netstats_rx_add.
Fixes: 761876c857cb ("tap: XDP support") Signed-off-by: Yunjian Wang <wangyunjian@huawei.com> Reviewed-by: Willem de Bruijn <willemb@google.com> Acked-by: Jason Wang <jasowang@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The commit 8ae1aff0b331 ("tuntap: split out XDP logic") includes
dropped counter for XDP_DROP, XDP_ABORTED, and invalid XDP actions.
Unfortunately, that commit missed the dropped counter when error
occurs during XDP_TX and XDP_REDIRECT actions. This patch fixes
this issue.
Fixes: 8ae1aff0b331 ("tuntap: split out XDP logic") Signed-off-by: Yunjian Wang <wangyunjian@huawei.com> Reviewed-by: Willem de Bruijn <willemb@google.com> Acked-by: Jason Wang <jasowang@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Mark reports a BUG() when a net namespace is removed.
kernel BUG at net/core/dev.c:11520!
Physical interfaces moved outside of init_net get "refunded"
to init_net when that namespace disappears. The main interface
name may get overwritten in the process if it would have
conflicted. We need to also discard all conflicting altnames.
Recent fixes addressed ensuring that altnames get moved
with the main interface, which surfaced this problem.
Reported-by: Марк Коренберг <socketpair@gmail.com> Link: https://lore.kernel.org/all/CAEmTpZFZ4Sv3KwqFOY2WKDHeZYdi0O7N5H1nTvcGp=SAEavtDg@mail.gmail.com/ Fixes: 7663d522099e ("net: check for altname conflicts when changing netdev's netns") Signed-off-by: Jakub Kicinski <kuba@kernel.org> Reviewed-by: Eric Dumazet <edumazet@google.com> Reviewed-by: Jiri Pirko <jiri@nvidia.com> Reviewed-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
idpf registers multiple netdevs (virtual ports) for one PCI function,
but it does not provide a way for userspace to distinguish them with
sysfs attributes. Per Documentation/ABI/testing/sysfs-class-net, it is
a bug not to set dev_port for independent ports on the same PCI bus,
device and function.
Without dev_port set, systemd-udevd's default naming policy attempts
to assign the same name ("ens2f0") to all four idpf netdevs on my test
system and obviously fails, leaving three of them with the initial
eth<N> name.
With this patch, systemd-udevd is able to assign unique names to the
netdevs (e.g. "ens2f0", "ens2f0d1", "ens2f0d2", "ens2f0d3").
The Intel-provided out-of-tree idpf driver already sets dev_port. In
this patch I chose to do it in the same place in the idpf_cfg_netdev
function.
Fixes: 0fe45467a104 ("idpf: add create vport and netdev configuration") Signed-off-by: Michal Schmidt <mschmidt@redhat.com> Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Generic sk_busy_loop_end() only looks at sk->sk_receive_queue
for presence of packets.
Problem is that for UDP sockets after blamed commit, some packets
could be present in another queue: udp_sk(sk)->reader_queue
In some cases, a busy poller could spin until timeout expiration,
even if some packets are available in udp_sk(sk)->reader_queue.
v3: - make sk_busy_loop_end() nicer (Willem)
v2: - add a READ_ONCE(sk->sk_family) in sk_is_inet() to avoid KCSAN splats.
- add a sk_is_inet() check in sk_is_udp() (Willem feedback)
- add a sk_is_inet() check in sk_is_tcp().
Fixes: 2276f58ac589 ("udp: use a separate rx queue for packet reception") Signed-off-by: Eric Dumazet <edumazet@google.com> Reviewed-by: Paolo Abeni <pabeni@redhat.com> Reviewed-by: Willem de Bruijn <willemb@google.com> Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
llc_conn_handler() initialises local variables {saddr,daddr}.mac
based on skb in llc_pdu_decode_sa()/llc_pdu_decode_da() and passes
them to __llc_lookup().
However, the initialisation is done only when skb->protocol is
htons(ETH_P_802_2), otherwise, __llc_lookup_established() and
__llc_lookup_listener() will read garbage.
The missing initialisation existed prior to commit 211ed865108e
("net: delete all instances of special processing for token ring").
It removed the part to kick out the token ring stuff but forgot to
close the door allowing ETH_P_TR_802_2 packets to sneak into llc_rcv().
Let's remove llc_tr_packet_type and complete the deprecation.
syzbot was able to trick llc_ui_sendmsg(), allocating an skb with no
headroom, but subsequently trying to push 14 bytes of Ethernet header [1]
Like some others, llc_ui_sendmsg() releases the socket lock before
calling sock_alloc_send_skb().
Then it acquires it again, but does not redo all the sanity checks
that were performed.
This fix:
- Uses LL_RESERVED_SPACE() to reserve space.
- Check all conditions again after socket lock is held again.
- Do not account Ethernet header for mtu limitation.
In the vlan_changelink function, a loop is used to parse the nested
attributes IFLA_VLAN_EGRESS_QOS and IFLA_VLAN_INGRESS_QOS in order to
obtain the struct ifla_vlan_qos_mapping. These two nested attributes are
checked in the vlan_validate_qos_map function, which calls
nla_validate_nested_deprecated with the vlan_map_policy.
However, this deprecated validator applies a LIBERAL strictness, allowing
the presence of an attribute with the type IFLA_VLAN_QOS_UNSPEC.
Consequently, the loop in vlan_changelink may parse an attribute of type
IFLA_VLAN_QOS_UNSPEC and believe it carries a payload of
struct ifla_vlan_qos_mapping, which is not necessarily true.
To address this issue and ensure compatibility, this patch introduces two
type checks that skip attributes whose type is not IFLA_VLAN_QOS_MAPPING.
Fixes: 07b5b17e157b ("[VLAN]: Use rtnl_link API") Signed-off-by: Lin Ma <linma@zju.edu.cn> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://lore.kernel.org/r/20240118130306.1644001-1-linma@zju.edu.cn Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / thirdparty / kernel / stable.git / log
