This is because we're holding the block_group->lock while trying to dump
the free space cache. However we don't need this lock, we just need it
to read the values for the printk, so move the free space cache dumping
outside of the block group lock.
Signed-off-by: Josef Bacik <josef@toxicpanda.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
As commit ef6b75671b5f ("mmc: sdhci-cadence: send tune request twice to
work around errata") stated, this IP has an errata. This commit applies
the second workaround for the SD mode.
Due to the errata, it is not possible to use the hardware tuning provided
by SDHCI_HOST_CONTROL2.
Use the software-controlled tuning like the eMMC mode.
Set sdhci_host_ops::platform_execute_tuning instead of overriding
mmc_host_ops::execute_tuning.
On calling pm_runtime_get_sync() the reference count of the device
is incremented. In case of failure, decrement the
ref count before returning the error.
nouveau_debugfs_strap_peek() calls pm_runtime_get_sync() that
increments the reference count. In case of failure, decrement the
ref count before returning the error.
Check for regmap_read() return code before using the read value in
following write in exynos5_switch_timing_regs(). Pass reading error
code to the callers.
This does not introduce proper error handling for such failed reads (and
obviously regmap_write() error is still ignored) because the driver
ignored this in all places. Therefor it only fixes reported issue while
matching current driver coding style:
drivers/memory/samsung/exynos5422-dmc.c: In function 'exynos5_switch_timing_regs':
>> drivers/memory/samsung/exynos5422-dmc.c:216:6: warning: variable 'ret' set but not used [-Wunused-but-set-variable]
Reported-by: kernel test robot <lkp@intel.com> Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
We can prevent potential incorrect DMA access attempts from the
NIC by enabling bus-master after the reset, and by disabling
bus-master earlier in cleanup.
Signed-off-by: Shannon Nelson <snelson@pensando.io> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
in etnaviv_gpu_submit, etnaviv_gpu_recover_hang, etnaviv_gpu_debugfs,
and etnaviv_gpu_init the call to pm_runtime_get_sync increments the
counter even in case of failure, leading to incorrect ref count.
In case of failure, decrement the ref count before returning.
hi3660-hikey960.dts:
Define a 'ports' node for 'adv7533: adv7533@39' and the
'adi,dsi-lanes' property to make it compliant with the adi,adv7533 DT
binding.
This fills the requirements to meet the binding requirements,
remote endpoints are not defined.
hi6220-hikey.dts:
Change property name s/pd-gpio/pd-gpios, gpio properties should be
plural. This is just a cosmetic change.
While we expose the ability to turn off hardware dithering for nouveau,
we actually make the mistake of turning it on anyway, due to
dithering_depth containing a non-zero value if our dithering depth isn't
also set to 6 bpc.
So, fix it by never enabling dithering when it's disabled.
neofb_probe() calls neo_scan_monitor() that can successfully allocate a
memory for info->monspecs.modedb and proceed to case 0x03. There it does
not free the memory and returns -1. neofb_probe() goes to label
err_scan_monitor, thus, it does not free this memory through calling
fb_destroy_modedb() as well. We can not go to label err_init_hw since
neo_scan_monitor() can fail during memory allocation. So, the patch frees
the memory directly for case 0x03.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Evgeny Novikov <novikov@ispras.ru> Cc: Jani Nikula <jani.nikula@intel.com> Cc: Mike Rapoport <rppt@linux.ibm.com> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200630195451.18675-1-novikov@ispras.ru Signed-off-by: Sasha Levin <sashal@kernel.org>
savagefb_probe() calls savage_init_fb_info() that can successfully
allocate memory for info->pixmap.addr but then fail when
fb_alloc_cmap() fails. savagefb_probe() goes to label failed_init and
does not free allocated memory. It is not valid to go to label
failed_mmio since savage_init_fb_info() can fail during memory
allocation as well. So, the patch free allocated memory on the error
handling path in savage_init_fb_info() itself.
Found by Linux Driver Verification project (linuxtesting.org).
When building with LLVM_IAS=1 means using Clang's Integrated Assembly (IAS)
from LLVM/Clang >= v10.0.1-rc1+ instead of GNU/as from GNU/binutils
I see the following breakage in Debian/testing AMD64:
<instantiation>:15:74: error: too many positional arguments
PRECOMPUTE 8*3+8(%rsp), %xmm1, %xmm2, %xmm3, %xmm4, %xmm5, %xmm6, %xmm7,
^
arch/x86/crypto/aesni-intel_asm.S:1598:2: note: while in macro instantiation
GCM_INIT %r9, 8*3 +8(%rsp), 8*3 +16(%rsp), 8*3 +24(%rsp)
^
<instantiation>:47:2: error: unknown use of instruction mnemonic without a size suffix
GHASH_4_ENCRYPT_4_PARALLEL_dec %xmm9, %xmm10, %xmm11, %xmm12, %xmm13, %xmm14, %xmm0, %xmm1, %xmm2, %xmm3, %xmm4, %xmm5, %xmm6, %xmm7, %xmm8, enc
^
arch/x86/crypto/aesni-intel_asm.S:1599:2: note: while in macro instantiation
GCM_ENC_DEC dec
^
<instantiation>:15:74: error: too many positional arguments
PRECOMPUTE 8*3+8(%rsp), %xmm1, %xmm2, %xmm3, %xmm4, %xmm5, %xmm6, %xmm7,
^
arch/x86/crypto/aesni-intel_asm.S:1686:2: note: while in macro instantiation
GCM_INIT %r9, 8*3 +8(%rsp), 8*3 +16(%rsp), 8*3 +24(%rsp)
^
<instantiation>:47:2: error: unknown use of instruction mnemonic without a size suffix
GHASH_4_ENCRYPT_4_PARALLEL_enc %xmm9, %xmm10, %xmm11, %xmm12, %xmm13, %xmm14, %xmm0, %xmm1, %xmm2, %xmm3, %xmm4, %xmm5, %xmm6, %xmm7, %xmm8, enc
^
arch/x86/crypto/aesni-intel_asm.S:1687:2: note: while in macro instantiation
GCM_ENC_DEC enc
Craig Topper suggested me in ClangBuiltLinux issue #1050:
> I think the "too many positional arguments" is because the parser isn't able
> to handle the trailing commas.
>
> The "unknown use of instruction mnemonic" is because the macro was named
> GHASH_4_ENCRYPT_4_PARALLEL_DEC but its being instantiated with
> GHASH_4_ENCRYPT_4_PARALLEL_dec I guess gas ignores case on the
> macro instantiation, but llvm doesn't.
First, I removed the trailing comma in the PRECOMPUTE line.
On calling pm_runtime_get_sync() the reference count of the device
is incremented. In case of failure, decrement the
reference count before returning the error.
Acked-by: Evan Quan <evan.quan@amd.com> Signed-off-by: Aditya Pakki <pakki001@umn.edu> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Check if irq_src is NULL to avoid dereferencing a NULL pointer,
for MES ring is uneccessary to recieve an interrupt notification.
Signed-off-by: Jack Xiao <Jack.Xiao@amd.com> Acked-by: Alex Deucher <alexander.deucher@amd.com> Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
On a PREEMPT=n kernel, the try_release_extent_mapping() function's
"while" loop might run for a very long time on a large I/O. This commit
therefore adds a cond_resched() to this loop, providing RCU any needed
quiescent states.
Signed-off-by: Paul E. McKenney <paulmck@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Be pedantic on removal as well and hold the mutex.
This should prevent uses of addition while we exit.
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org> Reviewed-by: Ming Lei <ming.lei@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
In the case we set or free the global value listen_chan in
different threads, we can encounter the UAF problems because
the method is not protected by any lock, add one to avoid
this bug.
BUG: KASAN: use-after-free in l2cap_chan_close+0x48/0x990
net/bluetooth/l2cap_core.c:730
Read of size 8 at addr ffff888096950000 by task kworker/1:102/2868
This "alert" error message can be seen on exynos4412-odroidx2:
L2C: platform modifies aux control register: 0x02070000 -> 0x3e470001
L2C: platform provided aux values permit register corruption.
Followed by this plain error message:
L2C-310: enabling full line of zeros but not enabled in Cortex-A9
To fix it, don't set the L310_AUX_CTRL_FULL_LINE_ZERO flag (bit 0) in
the default value of l2c_aux_val. It may instead be enabled when
applicable by the logic in l2c310_enable() if the attribute
"arm,full-line-zero-disable" was set in the device tree.
The initial commit that introduced this default value was in v2.6.38
commit 1cf0eb799759 ("ARM: S5PV310: Add L2 cache init function in
cpu.c").
However, the code to set the L310_AUX_CTRL_FULL_LINE_ZERO flag and
manage that feature was added much later and the default value was not
updated then. So this seems to have been a subtle oversight
especially since enabling it only in the cache and not in the A9 core
doesn't actually prevent the platform from running. According to the
TRM, the opposite would be a real issue, if the feature was enabled in
the A9 core but not in the cache controller.
The ocelot hardware designers have made some hacks to support multicast
IPv4 and IPv6 addresses. Normally, the MAC table matches on MAC
addresses and the destination ports are selected through the DEST_IDX
field of the respective MAC table entry. The DEST_IDX points to a Port
Group ID (PGID) which contains the bit mask of ports that frames should
be forwarded to. But there aren't a lot of PGIDs (only 80 or so) and
there are clearly many more IP multicast addresses than that, so it
doesn't scale to use this PGID mechanism, so something else was done.
Since the first portion of the MAC address is known, the hack they did
was to use a single PGID for _flooding_ unknown IPv4 multicast
(PGID_MCIPV4 == 62), but for known IP multicast, embed the destination
ports into the first 3 bytes of the MAC address recorded in the MAC
table.
The VSC7514 datasheet explains it like this:
3.9.1.5 IPv4 Multicast Entries
MAC table entries with the ENTRY_TYPE = 2 settings are interpreted
as IPv4 multicast entries.
IPv4 multicasts entries match IPv4 frames, which are classified to
the specified VID, and which have DMAC = 0x01005Exxxxxx, where
xxxxxx is the lower 24 bits of the MAC address in the entry.
Instead of a lookup in the destination mask table (PGID), the
destination set is programmed as part of the entry MAC address. This
is shown in the following table.
Table 78: IPv4 Multicast Destination Mask
Destination Ports Record Bit Field
---------------------------------------------
Ports 10-0 MAC[34-24]
Example: All IPv4 multicast frames in VLAN 12 with MAC 01005E112233 are
to be forwarded to ports 3, 8, and 9. This is done by inserting the
following entry in the MAC table entry:
VALID = 1
VID = 12
MAC = 0x000308112233
ENTRY_TYPE = 2
DEST_IDX = 0
But this procedure is not at all what's going on in the driver. In fact,
the code that embeds the ports into the MAC address looks like it hasn't
actually been tested. This patch applies the procedure described in the
datasheet.
Since there are many other fixes to be made around multicast forwarding
until it works properly, there is no real reason for this patch to be
backported to stable trees, or considered a real fix of something that
should have worked.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
rpmh-rsc driver is fairly core to system and should not be removable
once its probed. However it allows to unbind driver from sysfs using
below command which results into a crash on sc7180.
When the device is already gone we end up with the following scenario:
The device's capacity is 0 and thus the number of zones will be 0 as well. When
allocating the bitmap for the conventional zones, we then trip over a NULL
pointer.
So if we encounter a zoned block device with a 0 capacity, don't dare to
revalidate the zones sizes.
Fixes: 6c6b35491422 ("block: set the zone size in blk_revalidate_disk_zones atomically") Signed-off-by: Johannes Thumshirn <johannes.thumshirn@wdc.com> Reviewed-by: Damien Le Moal <damien.lemoal@wdc.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
When nvme_round_robin_path() finds a valid namespace we should be using it;
falling back to __nvme_find_path() for non-optimized paths will cause the
result from nvme_round_robin_path() to be ignored for non-optimized paths.
Fixes: 75c10e732724 ("nvme-multipath: round-robin I/O policy") Signed-off-by: Martin Wilck <mwilck@suse.com> Signed-off-by: Hannes Reinecke <hare@suse.de> Reviewed-by: Sagi Grimberg <sagi@grimberg.me> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
commit fe35ec58f0d3 ("block: update hctx map when use multiple maps")
exposed an issue where we may hang trying to wait for queue freeze
during I/O. We call blk_mq_update_nr_hw_queues which in case of multiple
queue maps (which we have now for default/read/poll) is attempting to
freeze the queue. However we never started queue freeze when starting the
reset, which means that we have inflight pending requests that entered the
queue that we will not complete once the queue is quiesced.
So start a freeze before we quiesce the queue, and unfreeze the queue
after we successfully connected the I/O queues (and make sure to call
blk_mq_update_nr_hw_queues only after we are sure that the queue was
already frozen).
This follows to how the pci driver handles resets.
Fixes: fe35ec58f0d3 ("block: update hctx map when use multiple maps") Signed-off-by: Sagi Grimberg <sagi@grimberg.me> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
commit fe35ec58f0d3 ("block: update hctx map when use multiple maps")
exposed an issue where we may hang trying to wait for queue freeze
during I/O. We call blk_mq_update_nr_hw_queues which in case of multiple
queue maps (which we have now for default/read/poll) is attempting to
freeze the queue. However we never started queue freeze when starting the
reset, which means that we have inflight pending requests that entered the
queue that we will not complete once the queue is quiesced.
So start a freeze before we quiesce the queue, and unfreeze the queue
after we successfully connected the I/O queues (and make sure to call
blk_mq_update_nr_hw_queues only after we are sure that the queue was
already frozen).
This follows to how the pci driver handles resets.
Fixes: fe35ec58f0d3 ("block: update hctx map when use multiple maps") Signed-off-by: Sagi Grimberg <sagi@grimberg.me> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
# ./scripts/faddr2line vmlinux its_cpu_init+0x6f4/0xe40
its_cpu_init+0x6f4/0xe40:
allocate_vpe_l1_table at drivers/irqchip/irq-gic-v3-its.c:2818
(inlined by) its_cpu_init_lpis at drivers/irqchip/irq-gic-v3-its.c:3138
(inlined by) its_cpu_init at drivers/irqchip/irq-gic-v3-its.c:5166
It turned out that we're allocating memory using GFP_KERNEL (may sleep)
within the CPU hotplug notifier, which is indeed an atomic context. Bad
thing may happen if we're playing on a system with more than a single
CommonLPIAff group. Avoid it by turning this into an atomic allocation.
Commit 01397e822af4 ("kunit: Fix TabError, remove defconfig code and
handle when there is no kunitconfig") and commit 45ba7a893ad8 ("kunit:
kunit_tool: Separate out config/build/exec/parse") introduced two
closely related issues which built off of each other: they excessively
created the build directory when not present and modified a constant
(constants in Python only exist by convention).
Together these issues broken a number of unit tests for KUnit tool, so
fix them.
Fixed up commit log to fic checkpatch commit description style error.
Shuah Khan <skhan@linuxfoundation.org>
Fixes: 01397e822af4 ("kunit: Fix TabError, remove defconfig code and handle when there is no kunitconfig") Fixes: 45ba7a893ad8 ("kunit: kunit_tool: Separate out config/build/exec/parse") Signed-off-by: Brendan Higgins <brendanhiggins@google.com> Signed-off-by: Shuah Khan <skhan@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit ddbd60c779b4 ("kunit: use --build_dir=.kunit as default") changed
the default build directory for KUnit tests, but failed to update
associated unit tests for kunit_tool, so update them.
Fixes: ddbd60c779b4 ("kunit: use --build_dir=.kunit as default") Signed-off-by: Brendan Higgins <brendanhiggins@google.com> Signed-off-by: Shuah Khan <skhan@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Check the return value of irq_domain_translate_twocell() due to
it may returns -EINVAL if failed and use variable fwspec for it,
and then use a new variable parent_fwspec which is proper for
irq_domain_alloc_irqs_parent().
In the function htvec_of_init(), system resource "parent_irq"
was not released in an error case. Thus add a jump target for
the completion of the desired exception handling.
Pointer mddev is being dereferenced with a test_bit call before mddev
is being null checked, this may cause a null pointer dereference. Fix
this by moving the null pointer checks to sanity check mddev before
it is dereferenced.
Addresses-Coverity: ("Dereference before null check") Fixes: 62f7b1989c02 ("md raid0/linear: Mark array as 'broken' and fail BIOs if a member is gone") Signed-off-by: Colin Ian King <colin.king@canonical.com> Reviewed-by: Guilherme G. Piccoli <gpiccoli@canonical.com> Signed-off-by: Song Liu <songliubraving@fb.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When SECCOMP_IOCTL_NOTIF_ID_VALID was first introduced it had the wrong
direction flag set. While this isn't a big deal as nothing currently
enforces these bits in the kernel, it should be defined correctly. Fix
the define and provide support for the old command until it is no longer
needed for backward compatibility.
Fixes: 6a21cc50f0c7 ("seccomp: add a return code to trap to userspace") Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
commit e3e0b582c321 ("selinux: remove unused initial SIDs and improve
handling") broke scripts/selinux/mdp since the unused initial SID names
were removed and the corresponding generation of policy initial SID
definitions by mdp was not updated accordingly. Fix it. With latest
upstream checkpolicy it is no longer necessary to include the SID context
definitions for the unused initial SIDs but retain them for compatibility
with older checkpolicy.
Fixes: e3e0b582c321 ("selinux: remove unused initial SIDs and improve handling") Signed-off-by: Stephen Smalley <stephen.smalley.work@gmail.com> Signed-off-by: Paul Moore <paul@paul-moore.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
if of_find_device_by_node() succeed, socfpga_setup_ocram_self_refresh
doesn't have a corresponding put_device(). Thus add a jump target to
fix the exception handling for this function implementation.
Fixes: 44fd8c7d4005 ("ARM: socfpga: support suspend to ram") Signed-off-by: Yu Kuai <yukuai3@huawei.com> Signed-off-by: Dinh Nguyen <dinguyen@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The RXFLR is possible larger than rx_left in Rockchip SPI, fix it.
Fixes: 01b59ce5dac8 ("spi: rockchip: use irq rather than polling") Signed-off-by: Jon Lin <jon.lin@rock-chips.com> Tested-by: Emil Renner Berthing <kernel@esmil.dk> Reviewed-by: Heiko Stuebner <heiko@sntech.de> Reviewed-by: Emil Renner Berthing <kernel@esmil.dk> Link: https://lore.kernel.org/r/20200723004356.6390-3-jon.lin@rock-chips.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The Protection Domains (PD) have a mechanism to keep its resources
enabled until the PD down indication is acked. Reorder the PD state
indication ack so that clients get to release the relevant resources
before the PD goes down.
I do not see the same on VIM3L, so remove sd-uhs-sdr50 from the common dtsi
to silence the error, then (re)add it to the VIM3L dts.
Fixes: 4f26cc1c96c9 ("arm64: dts: khadas-vim3: move common nodes into meson-khadas-vim3.dtsi") Fixes: 700ab8d83927 ("arm64: dts: khadas-vim3: add support for the SM1 based VIM3L") Signed-off-by: Christian Hewitt <christianshewitt@gmail.com> Signed-off-by: Kevin Hilman <khilman@baylibre.com> Link: https://lore.kernel.org/r/20200721015950.11816-1-christianshewitt@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
rings_size() sets sq_offset to the total size of the rings (the returned
value which is used for memory allocation). This is wrong: sq array should
be located within the rings, not after them. Set sq_offset to where it
should be.
The change corrects registration and deregistration on error path
of a regulator, the problem was manifested by a reported memory
leak on deferred probe:
The memory leak problem was introduced as a side ef another fix in
regulator_register() error path, I believe that the proper fix is
to decouple device_register() function into its two compounds and
initialize a struct device before assigning any values to its fields
and then using it before actual registration of a device happens.
This lets to call put_device() safely after initialization, and, since
now a release callback is called, kfree(rdev->constraints) shall be
removed to exclude a double free condition.
Fixes: a3cde9534ebd ("regulator: core: fix regulator_register() error paths to properly release rdev") Signed-off-by: Vladimir Zapolskiy <vz@mleia.com> Cc: Wen Yang <wenyang@linux.alibaba.com> Link: https://lore.kernel.org/r/20200724005013.23278-1-vz@mleia.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently, if a section has a relocation to '_mcount' symbol, a new
__mcount_loc entry will be added whatever the relocation type is.
This is problematic when a relocation to '_mcount' is in the middle of a
section and is not a call for ftrace use.
Such relocation could be generated with below code for example:
bool is_mcount(unsigned long addr)
{
return (target == (unsigned long) &_mcount);
}
With this snippet of code, ftrace will try to patch the mcount location
generated by this code on module load and fail with:
Require that the TCG_PCR_EVENT2.digests.count value strictly matches the
value of TCG_EfiSpecIdEvent.numberOfAlgorithms in the event field of the
TCG_PCClientPCREvent event log header. Also require that
TCG_EfiSpecIdEvent.numberOfAlgorithms is non-zero.
The TCG PC Client Platform Firmware Profile Specification section 9.1
(Family "2.0", Level 00 Revision 1.04) states:
For each Hash algorithm enumerated in the TCG_PCClientPCREvent entry,
there SHALL be a corresponding digest in all TCG_PCR_EVENT2 structures.
Note: This includes EV_NO_ACTION events which do not extend the PCR.
Section 9.4.5.1 provides this description of
TCG_EfiSpecIdEvent.numberOfAlgorithms:
The number of Hash algorithms in the digestSizes field. This field MUST
be set to a value of 0x01 or greater.
Enforce these restrictions, as required by the above specification, in
order to better identify and ignore invalid sequences of bytes at the
end of an otherwise valid TPM2 event log. Firmware doesn't always have
the means necessary to inform the kernel of the actual event log size so
the kernel's event log parsing code should be stringent when parsing the
event log for resiliency against firmware bugs. This is true, for
example, when firmware passes the event log to the kernel via a reserved
memory region described in device tree.
POWER and some ARM systems use the "linux,sml-base" and "linux,sml-size"
device tree properties to describe the memory region used to pass the
event log from firmware to the kernel. Unfortunately, the
"linux,sml-size" property describes the size of the entire reserved
memory region rather than the size of the event long within the memory
region and the event log format does not include information describing
the size of the event log.
tpm_read_log_of(), in drivers/char/tpm/eventlog/of.c, is where the
"linux,sml-size" property is used. At the end of that function,
log->bios_event_log_end is pointing at the end of the reserved memory
region. That's typically 0x10000 bytes offset from "linux,sml-base",
depending on what's defined in the device tree source.
The firmware event log only fills a portion of those 0x10000 bytes and
the rest of the memory region should be zeroed out by firmware. Even in
the case of a properly zeroed bytes in the remainder of the memory
region, the only thing allowing the kernel's event log parser to detect
the end of the event log is the following conditional in
__calc_tpm2_event_size():
If that wasn't there, __calc_tpm2_event_size() would think that a 16
byte sequence of zeroes, following an otherwise valid event log, was
a valid event.
However, problems can occur if a single bit is set in the offset
corresponding to either the TCG_PCR_EVENT2.eventType or
TCG_PCR_EVENT2.eventSize fields, after the last valid event log entry.
This could confuse the parser into thinking that an additional entry is
present in the event log and exposing this invalid entry to userspace in
the /sys/kernel/security/tpm0/binary_bios_measurements file. Such
problems have been seen if firmware does not fully zero the memory
region upon a warm reboot.
This patch significantly raises the bar on how difficult it is for
stale/invalid memory to confuse the kernel's event log parser but
there's still, ultimately, a reliance on firmware to properly initialize
the remainder of the memory region reserved for the event log as the
parser cannot be expected to detect a stale but otherwise properly
formatted firmware event log entry.
Fixes: fd5c78694f3f ("tpm: fix handling of the TPM 2.0 event logs") Signed-off-by: Tyler Hicks <tyhicks@linux.microsoft.com> Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
It turns out having a Rx DMA channel serviced with higher priority than
a Tx DMA channel is not enough to provide a well balanced DMA-based SPI
transfer interface. There might still be moments when the Tx DMA channel
is occasionally handled faster than the Rx DMA channel. That in its turn
will eventually cause the SPI Rx FIFO overflow if SPI bus speed is high
enough to fill the SPI Rx FIFO in before it's cleared by the Rx DMA
channel. That's why having the DMA-based SPI Tx interface too optimized
is the errors prone, so the commit 0b2b66514fc9 ("spi: dw: Use DMA max
burst to set the request thresholds") though being perfectly normal from
the standard functionality point of view implicitly introduced the problem
described above. In order to fix that the Tx DMA activity is intentionally
slowed down by limiting the SPI Tx FIFO depth with a value twice bigger
than the Tx burst length calculated earlier by the
dw_spi_dma_maxburst_init() method.
Fixes: 0b2b66514fc9 ("spi: dw: Use DMA max burst to set the request thresholds") Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Cc: Andy Shevchenko <andy.shevchenko@gmail.com> Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru> Cc: Feng Tang <feng.tang@intel.com> Link: https://lore.kernel.org/r/20200721203951.2159-1-Sergey.Semin@baikalelectronics.ru Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The Bananapi M2+ uses a GPIO line to change the effective resistance of
the CPU supply regulator's feedback resistor network. The voltages
described in the device tree were given directly by the vendor. This
turns out to be slightly off compared to the real values.
The updated voltages are based on calculations of the feedback resistor
network, and verified down to three decimal places with a multi-meter.
The device tree currently only assigns the a supply for the first CPU
core, when in reality the regulator supply is shared by all four cores.
This might cause an issue if the implementation does not realize the
sharing of the supply.
Assign the same regulator supply to the remaining CPU cores to address
this.
Since commit bcf3440c6dd7 ("net: phy: micrel: add phy-mode support for the
KSZ9031 PHY"), networking is broken on sama5d3 xplained.
The device tree has phy-mode = "rgmii" and this worked before, because
KSZ9031 PHY started with default RGMII internal delays configuration (TX
off, RX on 1.2 ns) and MAC provided TX delay. After above commit, the
KSZ9031 PHY starts handling phy mode properly and disables RX delay, as
result networking is become broken.
Fix it by switching to phy-mode = "rgmii-rxid" to reflect previous
behavior.
kernel test robot reports a compile warning about REG_OFFSET redefined
in the reset-intel-gw.c after merging commit e44ab4e14d6f4 ("regmap:
Simplify implementation of the regmap_read_poll_timeout() macro"). the
warning is like that:
In file included from ./arch/arm/mach-ixp4xx/include/mach/hardware.h:30:0,
from ./arch/arm/mach-ixp4xx/include/mach/io.h:15,
from ./arch/arm/include/asm/io.h:198,
from ./include/linux/io.h:13,
from ./include/linux/iopoll.h:14,
from ./include/linux/regmap.h:20,
from drivers/reset/reset-intel-gw.c:12:
./arch/arm/mach-ixp4xx/include/mach/platform.h:25:0: note: this is the location of the previous definition
#define REG_OFFSET 3
Reported-by: kernel test robot <lkp@intel.com> Fixes: c9aef213e38cde ("reset: intel: Add system reset controller driver") Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com> Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit 1019fe2c7280 ("ARM: dts: exynos: Adjust bus related OPPs to the
values correct for Exynos5422 Odroids") changed the parameters of the
OPPs for the FSYS bus. Besides the frequency adjustments, it also removed
the 'shared-opp' property from the OPP table used for FSYS_APB and FSYS
busses.
This revealed that in fact the FSYS bus frequency scaling never worked.
When one OPP table is marked as 'opp-shared', only the first bus which
selects the OPP sets the rate of its clock. Then OPP core assumes that
the other busses have been changed to that OPP and no change to their
clock rates are needed. Thus when FSYS_APB bus, which was registered
first, set the rate for its clock, the OPP core did not change the FSYS
bus clock later.
The mentioned commit removed that behavior, what introduced a regression
on some Odroid XU3 boards. Frequency scaling of the FSYS bus causes
instability of the USB host operation, what can be observed as network
hangs. To restore old behavior, simply disable frequency scaling for the
FSYS bus.
Reported-by: Willy Wolff <willy.mh.wolff.ml@gmail.com> Fixes: 1019fe2c7280 ("ARM: dts: exynos: Adjust bus related OPPs to the values correct for Exynos5422 Odroids") Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
if of_find_device_by_node() succeed, at91_pm_sram_init() doesn't have
a corresponding put_device(). Thus add a jump target to fix the exception
handling for this function implementation.
Fixes: d2e467905596 ("ARM: at91: pm: use the mmio-sram pool to access SRAM") Signed-off-by: yu kuai <yukuai3@huawei.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Link: https://lore.kernel.org/r/20200604123301.3905837-1-yukuai3@huawei.com Signed-off-by: Sasha Levin <sashal@kernel.org>
In the function check_acpi_dev(), if it fails to create
platform device, the return value is ERR_PTR() or NULL.
Thus it must use IS_ERR_OR_NULL() to check return value.
Fixes: 332e081225fc ("intel-vbtn: new driver for Intel Virtual Button") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Lu Wei <luwei32@huawei.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In the function check_acpi_dev(), if it fails to create
platform device, the return value is ERR_PTR() or NULL.
Thus it must use IS_ERR_OR_NULL() to check return value.
Fixes: ecc83e52b28c ("intel-hid: new hid event driver for hotkeys") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Lu Wei <luwei32@huawei.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When writing values to the IOP status/control register make sure those
values do not have any extraneous bits that will clear interrupt flags.
To place the SCC IOP into bypass mode would be desirable but this is not
achieved by writing IOP_DMAINACTIVE | IOP_RUN | IOP_AUTOINC | IOP_BYPASS
to the control register. Drop this ineffective register write.
Remove the flawed and unused iop_bypass() function. Make use of the
unused iop_stop() function.
Avoid this by testing the channel state before calling iop_do_send().
When sending, and iop_send_queue is empty, call iop_do_send() because
the channel is idle. If iop_send_queue is not empty, iop_do_send() will
get called later by iop_handle_send().
Currently we are not initializing the scmi clock with discrete rates
correctly. We fetch the min_rate and max_rate value only for clocks with
ranges and ignore the ones with discrete rates. This will lead to wrong
initialization of rate range when clock supports discrete rate.
Fix this by using the first and the last rate in the sorted list of the
discrete clock rates while registering the clock.
Link: https://lore.kernel.org/r/20200709081705.46084-2-sudeep.holla@arm.com Fixes: 6d6a1d82eaef7 ("clk: add support for clocks provided by SCMI") Reviewed-by: Stephen Boyd <sboyd@kernel.org> Reported-and-tested-by: Dien Pham <dien.pham.ry@renesas.com> Signed-off-by: Sudeep Holla <sudeep.holla@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
struct uclamp_rq was zeroed out entirely in assumption that in the first
call to uclamp_rq_inc() they'd be initialized correctly in accordance to
default settings.
But when next patch introduces a static key to skip
uclamp_rq_{inc,dec}() until userspace opts in to use uclamp, schedutil
will fail to perform any frequency changes because the
rq->uclamp[UCLAMP_MAX].value is zeroed at init and stays as such. Which
means all rqs are capped to 0 by default.
Fix it by making sure we do proper initialization at init without
relying on uclamp_rq_inc() doing it later.
Once regulators are disabled after kernel boot, on Espresso board silent
hang observed because of LDO7 being disabled. LDO7 actually provide
power to CPU cores and non-cpu blocks circuitries. Keep this regulator
always-on to fix this hang.
Fixes: 9589f7721e16 ("arm64: dts: Add S2MPS15 PMIC node on exynos7-espresso") Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com> Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Some outputs from the RTL8723CS are connected to the PL port (BT_WAKE_AP),
which runs at 1.8V. When BT_WAKE_AP is high, the PL pin this signal is
connected to is overdriven, and the whole PL port's voltage rises
somewhat. This results in changing voltage on the R_PWM pin (PL10),
which is the cause for backlight flickering very noticeably when typing
on a Bluetooth keyboard, because backlight intensity is highly sensitive
to the voltage of the R_PWM pin.
Limit the maximum WiFi/BT I/O voltage to 1.8V to avoid overdriving
the PL port pins via BT and WiFi IO port signals. WiFi and BT
functionality is unaffected by this change.
This completely stops the backlight flicker when using bluetooth.
Fixes: 91f480d40942 ("arm64: dts: allwinner: Add initial support for Pine64 PinePhone") Signed-off-by: Ondrej Jirman <megous@megous.com> Link: https://lore.kernel.org/r/20200703194842.111845-4-megous@megous.com Signed-off-by: Maxime Ripard <maxime@cerno.tech> Signed-off-by: Sasha Levin <sashal@kernel.org>
It is possible that one of the channels cannot be detached
because its free channel is busy and previously queued data
has not been processed yet. On the other hand, another
channel can be successfully detached causing the monitor
work to stop.
Prevent that by rescheduling the monitor work if there are
any channels in the pending state after a detach attempt.
Fixes: 34c881745549e ("rcu: Support kfree_bulk() interface in kfree_rcu()") Acked-by: Joel Fernandes (Google) <joel@joelfernandes.org> Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Signed-off-by: Paul E. McKenney <paulmck@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Call exynos_cpu_power_up(cpunr) unconditionally. This is needed by the
big.LITTLE cpuidle driver and has no side-effects on other code paths.
The additional soft-reset call during little core power up has been added
to properly boot all cores on the Exynos5422-based boards with secure
firmware (like Odroid XU3/XU4 family). This however broke big.LITTLE
CPUidle driver, which worked only on boards without secure firmware (like
Peach-Pit/Pi Chromebooks). Apply the workaround only when board is
running under secure firmware.
Fixes: 833b5794e330 ("ARM: EXYNOS: reset Little cores when cpu is up") Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Reviewed-by: Lukasz Luba <lukasz.luba@arm.com> Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The write_tcs_reg_sync() may be called after timekeeping is suspended
so it's not OK to use ktime. The readl_poll_timeout_atomic() macro
implicitly uses ktime. This was causing a warning at suspend time.
Change to just loop 1000000 times with a delay of 1 us between loops.
This may give a timeout of more than 1 second but never less and is
safe even if timekeeping is suspended.
NOTE: I don't have any actual evidence that we need to loop here.
It's possibly that all we really need to do is just read the value
back to ensure that the pipes are cleaned and the looping/comparing is
totally not needed. I never saw the loop being needed in my tests.
However, the loop shouldn't hurt.
Reviewed-by: Stephen Boyd <sboyd@kernel.org> Reviewed-by: Maulik Shah <mkshah@codeaurora.org> Fixes: 91160150aba0 ("soc: qcom: rpmh-rsc: Timeout after 1 second in write_tcs_reg_sync()") Reported-by: Maulik Shah <mkshah@codeaurora.org> Signed-off-by: Douglas Anderson <dianders@chromium.org> Link: https://lore.kernel.org/r/20200528074530.1.Ib86e5b406fe7d16575ae1bb276d650faa144b63c@changeid Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
On commit 6ac93117ab00 ("blktrace: use existing disk debugfs directory")
merged on v4.12 Omar fixed the original blktrace code for request-based
drivers (multiqueue). This however left in place a possible crash, if you
happen to abuse blktrace while racing to remove / add a device.
We used to use asynchronous removal of the request_queue, and with that
the issue was easier to reproduce. Now that we have reverted to
synchronous removal of the request_queue, the issue is still possible to
reproduce, its however just a bit more difficult.
We essentially run two instances of break-blktrace which add/remove
a loop device, and setup a blktrace and just never tear the blktrace
down. We do this twice in parallel. This is easily reproduced with the
script run_0004.sh from break-blktrace [0].
We can end up with two types of panics each reflecting where we
race, one a failed blktrace setup:
debugfs: Directory 'loop0' with parent 'block' already present
This crash happens because of how blktrace uses the debugfs directory
where it places its files. Upon init we always create the same directory
which would be needed by blktrace but we only do this for make_request
drivers (multiqueue) block drivers. When you race a removal of these
devices with a blktrace setup you end up in a situation where the
make_request recursive debugfs removal will sweep away the blktrace
files and then later blktrace will also try to remove individual
dentries which are already NULL. The inverse is also possible and hence
the two types of use after frees.
We don't create the block debugfs directory on init for these types of
block devices:
* request-based block driver block devices
* every possible partition
* scsi-generic
And so, this race should in theory only be possible with make_request
drivers.
We can fix the UAF by simply re-using the debugfs directory for
make_request drivers (multiqueue) and only creating the ephemeral
directory for the other type of block devices. The new clarifications
on relying on the q->blk_trace_mutex *and* also checking for q->blk_trace
*prior* to processing a blktrace ensures the debugfs directories are
only created if no possible directory name clashes are possible.
This goes tested with:
o nvme partitions
o ISCSI with tgt, and blktracing against scsi-generic with:
o block
o tape
o cdrom
o media changer
o blktests
This patch is part of the work which disputes the severity of
CVE-2019-19770 which shows this issue is not a core debugfs issue, but
a misuse of debugfs within blktace.
Fixes: 6ac93117ab00 ("blktrace: use existing disk debugfs directory") Reported-by: syzbot+603294af2d01acfdd6da@syzkaller.appspotmail.com Signed-off-by: Luis Chamberlain <mcgrof@kernel.org> Reviewed-by: Christoph Hellwig <hch@lst.de> Cc: Bart Van Assche <bvanassche@acm.org> Cc: Omar Sandoval <osandov@fb.com> Cc: Hannes Reinecke <hare@suse.com> Cc: Nicolai Stange <nstange@suse.de> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Michal Hocko <mhocko@kernel.org> Cc: "Martin K. Petersen" <martin.petersen@oracle.com> Cc: "James E.J. Bottomley" <jejb@linux.ibm.com> Cc: yu kuai <yukuai3@huawei.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
msm8916-pins.dtsi specifies "bias-pull-none" for most of the audio
pin configurations. This was likely copied from the qcom kernel fork
where the same property was used for these audio pins.
However, "bias-pull-none" actually does not exist at all - not in
mainline and not in downstream. I can only guess that the original
intention was to configure "no pull", i.e. bias-disable.
The crypto notify call occurs with a read mutex held so you must
not do any substantial work directly. In particular, you cannot
call crypto_alloc_* as they may trigger further notifications
which may dead-lock in the presence of another writer.
This patch fixes this by postponing the work into a work queue and
taking the same lock in the module init function.
While we're at it this patch also ensures that all RCU accesses are
marked appropriately (tested with sparse).
Finally this also reveals a race condition in module param show
function as it may be called prior to the module init function.
It's fixed by testing whether crct10dif_tfm is NULL (this is true
iff the init function has not completed assuming fallback is false).
Fixes: 11dcb1037f40 ("crc-t10dif: Allow current transform to be...") Fixes: b76377543b73 ("crc-t10dif: Pick better transform if one...") Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com> Reviewed-by: Eric Biggers <ebiggers@google.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
When kobject_init_and_add() returns an error, it should be handled
because kobject_init_and_add() takes a reference even when it fails. If
this function returns an error, kobject_put() must be called to properly
clean up the memory associated with the object.
Therefore, replace calling kfree() and call kobject_put() and add a
missing kobject_put() in the edac_device_register_sysfs_main_kobj()
error path.
The puma gmac node currently uses opposite active-values for the
gmac phy reset pin. The gpio-declaration uses active-high while the
separate snps,reset-active-low property marks the pin as active low.
While on the kernel side this works ok, other DT users may get
confused - as seen with uboot right now.
So bring this in line and make both properties match, similar to the
other Rockchip board.
The puma vcc5v0_host regulator node currently uses opposite active-values
for the enable pin. The gpio-declaration uses active-high while the
separate enable-active-low property marks the pin as active low.
While on the kernel side this works ok, other DT users may get
confused - as seen with uboot right now.
So bring this in line and make both properties match, similar to the
gmac fix.
The lion gmac node currently uses opposite active-values for the
gmac phy reset pin. The gpio-declaration uses active-high while the
separate snps,reset-active-low property marks the pin as active low.
While on the kernel side this works ok, other DT users may get
confused - as seen with uboot right now.
So bring this in line and make both properties match, similar to the
other Rockchip board.
During sched domain init, we check whether non-topological SD_flags are
returned by tl->sd_flags(), if found, fire a waning and correct the
violation, but the code failed to correct the violation. Correct this.
Fixes: 143e1e28cb40 ("sched: Rework sched_domain topology definition") Signed-off-by: Peng Liu <iwtbavbm@gmail.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Reviewed-by: Vincent Guittot <vincent.guittot@linaro.org> Reviewed-by: Valentin Schneider <valentin.schneider@arm.com> Link: https://lkml.kernel.org/r/20200609150936.GA13060@iZj6chx1xj0e0buvshuecpZ Signed-off-by: Sasha Levin <sashal@kernel.org>
With commit:
'b7031a02ec75 ("sched/fair: Add NOHZ_STATS_KICK")'
rebalance_domains of the local cfs_rq happens before others idle cpus have
updated nohz.next_balance and its value is overwritten.
Move the update of nohz.next_balance for other idles cpus before balancing
and updating the next_balance of local cfs_rq.
Also, the nohz.next_balance is now updated only if all idle cpus got a
chance to rebalance their domains and the idle balance has not been aborted
because of new activities on the CPU. In case of need_resched, the idle
load balance will be kick the next jiffie in order to address remaining
ilb.
Be defensive against the case where the processor reports a base_freq
larger than turbo_freq (the ratio would be zero).
Fixes: 1567c3e3467c ("x86, sched: Add support for frequency invariance") Signed-off-by: Giovanni Gherdovich <ggherdovich@suse.cz> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Link: https://lkml.kernel.org/r/20200531182453.15254-4-ggherdovich@suse.cz Signed-off-by: Sasha Levin <sashal@kernel.org>
There may be CPUs that support turbo boost but don't declare any turbo
ratio, i.e. their MSR_TURBO_RATIO_LIMIT is all zeroes. In that condition
scale-invariant calculations can't be performed.
Fixes: 1567c3e3467c ("x86, sched: Add support for frequency invariance") Suggested-by: Ricardo Neri <ricardo.neri-calderon@linux.intel.com> Signed-off-by: Giovanni Gherdovich <ggherdovich@suse.cz> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Tested-by: Ricardo Neri <ricardo.neri-calderon@linux.intel.com> Link: https://lkml.kernel.org/r/20200531182453.15254-3-ggherdovich@suse.cz Signed-off-by: Sasha Levin <sashal@kernel.org>
The product mcnt * arch_max_freq_ratio can overflows u64.
For context, a large value for arch_max_freq_ratio would be 5000,
corresponding to a turbo_freq/base_freq ratio of 5 (normally it's more like
1500-2000). A large increment frequency for the MPERF counter would be 5GHz
(the base clock of all CPUs on the market today is less than that). With
these figures, a CPU would need to go without a scheduler tick for around 8
days for the u64 overflow to happen. It is unlikely, but the check is
warranted.
Under similar conditions, the difference acnt of two consecutive APERF
readings can overflow as well.
In these circumstances is appropriate to disable frequency invariant
accounting: the feature relies on measures of the clock frequency done at
every scheduler tick, which need to be "fresh" to be at all meaningful.
A note on i386: prior to version 5.1, the GCC compiler didn't have the
builtin function __builtin_mul_overflow. In these GCC versions the macro
check_mul_overflow needs __udivdi3() to do (u64)a/b, which the kernel
doesn't provide. For this reason this change fails to build on i386 if
GCC<5.1, and we protect the entire frequency invariant code behind
CONFIG_X86_64 (special thanks to "kbuild test robot" <lkp@intel.com>).
Fixes: 1567c3e3467c ("x86, sched: Add support for frequency invariance") Signed-off-by: Giovanni Gherdovich <ggherdovich@suse.cz> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Link: https://lkml.kernel.org/r/20200531182453.15254-2-ggherdovich@suse.cz Signed-off-by: Sasha Levin <sashal@kernel.org>
When counting IMC uncore events on some TGL machines, an oops will be
triggered.
[ 393.101262] BUG: unable to handle page fault for address: ffffb45200e15858
[ 393.101269] #PF: supervisor read access in kernel mode
[ 393.101271] #PF: error_code(0x0000) - not-present page
Current perf uncore driver still use the IMC MAP SIZE inherited from
SNB, which is 0x6000.
However, the offset of IMC uncore counters is larger than 0x6000,
e.g. 0xd8a0.
Enlarge the IMC MAP SIZE for TGL to 0xe000.
Fixes: fdb64822443e ("perf/x86: Add Intel Tiger Lake uncore support") Reported-by: Ammy Yi <ammy.yi@intel.com> Signed-off-by: Kan Liang <kan.liang@linux.intel.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Tested-by: Ammy Yi <ammy.yi@intel.com> Tested-by: Chao Qin <chao.qin@intel.com> Link: https://lkml.kernel.org/r/1590679169-61823-1-git-send-email-kan.liang@linux.intel.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Some devices, particularly the 3DConnexion Spacemouse wireless 3D
controllers, return more than just the battery capacity in the battery
report. The Spacemouse devices return an additional byte with a device
specific field. However, hidinput_query_battery_capacity() only
requests a 2 byte transfer.
When a spacemouse is connected via USB (direct wire, no wireless dongle)
and it returns a 3 byte report instead of the assumed 2 byte battery
report the larger transfer confuses and frightens the USB subsystem
which chooses to ignore the transfer. Then after 2 seconds assume the
device has stopped responding and reset it. This can be reproduced
easily by using a wired connection with a wireless spacemouse. The
Spacemouse will enter a loop of resetting every 2 seconds which can be
observed in dmesg.
This patch solves the problem by increasing the transfer request to 4
bytes instead of 2. The fix isn't particularly elegant, but it is simple
and safe to backport to stable kernels. A further patch will follow to
more elegantly handle battery reports that contain additional data.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Cc: Darren Hart <darren@dvhart.com> Cc: Jiri Kosina <jikos@kernel.org> Cc: Benjamin Tissoires <benjamin.tissoires@redhat.com> Cc: stable@vger.kernel.org Tested-by: Darren Hart <dvhart@infradead.org> Signed-off-by: Jiri Kosina <jkosina@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Provide a helper to run task_work instead of checking and running
manually in a bunch of different spots. While doing so, also move the
task run state setting where we run the task work. Then we can move it
out of the callback helpers. This also helps ensure we only do this once
per task_work list run, not per task_work item.
projects / thirdparty / kernel / stable.git / log
