Coverity spotted that *buf is not initialized to zero in
mtk_pctrl_dbg_show. Using uninitialized variable *buf as argument to %s
when calling seq_printf. Fix this coverity by initializing *buf as zero.
Fixes: 184d8e13f9b1 ("pinctrl: mediatek: Add support for pin configuration dump via debugfs.") Signed-off-by: Guodong Liu <Guodong.Liu@mediatek.com> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Link: https://lore.kernel.org/r/20230118062036.26258-3-Guodong.Liu@mediatek.com Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Coverity spotted that pullen and pullup is not initialized to zero in
mtk_pctrl_show_one_pin. The uninitialized variable pullen is used in
assignment statement "rsel = pullen;" in mtk_pctrl_show_one_pin, and
Uninitialized variable pullup is used when calling scnprintf. Fix this
coverity by initializing pullen and pullup as zero.
Fixes: 184d8e13f9b1 ("pinctrl: mediatek: Add support for pin configuration dump via debugfs.") Signed-off-by: Guodong Liu <Guodong.Liu@mediatek.com> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Link: https://lore.kernel.org/r/20230118062036.26258-2-Guodong.Liu@mediatek.com Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
As kzalloc may fail and return NULL pointer,
it should be better to check cstate
in order to avoid the NULL pointer dereference
in __drm_atomic_helper_crtc_reset.
v2.5.0 support was originally added for SC7280, but this hw is also
present on SM8350, which has one more DSI host. Bump up the dsi count
and fill in the register of the secondary host to allow it to probe.
This should not have any adverse effects on SC7280, as the secondary
CTRL will only be touched if it's defined, anyway.
Fixes: 65c391b31994 ("drm/msm/dsi: Add DSI support for SC7280") Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org> Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/519513/ Link: https://lore.kernel.org/r/20230120210101.2146852-1-konrad.dybcio@linaro.org Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The MIPI DCS specification demands that brightness values are sent in
big endian byte order. It also states that one parameter (i.e. one byte)
shall be sent/received for 8 bit wide values, and two parameters shall
be used for values that are between 9 and 16 bits wide.
Add new functions to properly handle 16-bit brightness in big endian,
since the two 8- and 16-bit cases are distinct from each other.
[richard: use separate functions instead of switch/case]
[richard: split into 16-bit component]
Instead of having several fixed values for the pcr register, calculate
it before programming. This allows the bridge to support most of the
display modes.
Fixes: 23278bf54afe ("drm/bridge: Introduce LT9611 DSI to HDMI bridge") Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org> Link: https://patchwork.freedesktop.org/patch/msgid/20230118081658.2198520-6-dmitry.baryshkov@linaro.org Signed-off-by: Sasha Levin <sashal@kernel.org>
The driver will reset the bridge in the atomic_pre_enable(). However
this will also drop the HPD interrupt state. Instead of resetting the
bridge, properly wake it up. This fixes the HPD interrupt delivery after
the disable/enable cycle.
Fixes: 23278bf54afe ("drm/bridge: Introduce LT9611 DSI to HDMI bridge") Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org> Link: https://patchwork.freedesktop.org/patch/msgid/20230118081658.2198520-3-dmitry.baryshkov@linaro.org Signed-off-by: Sasha Levin <sashal@kernel.org>
On atomic_post_disable the bridge goes to the low power state. However
the code disables too much of the chip, so the HPD event is not being
detected and delivered to the host. Reduce the power saving in order to
get the HPD event.
Fixes: 23278bf54afe ("drm/bridge: Introduce LT9611 DSI to HDMI bridge") Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org> Link: https://patchwork.freedesktop.org/patch/msgid/20230118081658.2198520-2-dmitry.baryshkov@linaro.org Signed-off-by: Sasha Levin <sashal@kernel.org>
In the event that the topology requests resources that have not been
created by the system (because they are typically not represented in
dpu_mdss_cfg ^1), the resource(s) in global_state (in this case DSC
blocks, until their allocation/assignment is being sanity-checked in
"drm/msm/dpu: Reject topologies for which no DSC blocks are available")
remain NULL but will still be returned out of
dpu_rm_get_assigned_resources, where the caller expects to get an array
containing num_blks valid pointers (but instead gets these NULLs).
To prevent this from happening, where null-pointer dereferences
typically result in a hard-to-debug platform lockup, num_blks shouldn't
increase past NULL blocks and will print an error and break instead.
After all, max_blks represents the static size of the maximum number of
blocks whereas the actual amount varies per platform.
^1: which can happen after a git rebase ended up moving additions to
_dpu_cfg to a different struct which has the same patch context.
Initialize is_dsp_mode flag in the beginning of function
fsl_sai_set_dai_fmt_tr().
When the DAIFMT is DAIFMT_DSP_B the first time, is_dsp_mode is
true, then the second time DAIFMT is DAIFMT_I2S, is_dsp_mode
still true, which is a wrong state. So need to initialize
is_dsp_mode flag every time.
Fixes: a3f7dcc9cc03 ("ASoC: fsl-sai: Add SND_SOC_DAIFMT_DSP_A/B support.") Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com> Reviewed-by: Iuliana Prodan <iuliana.prodan@nxp.com> Link: https://lore.kernel.org/r/1673852874-32200-1-git-send-email-shengjiu.wang@nxp.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In large environment, it is possible to experience command timeout and
escalation of path recovery. Currently the driver does not track the number
of exchanges/commands sent to FW. If there is a delay for commands at the
head of the queue, then this will create back pressure for commands at the
back of the queue.
Check for exchange availability before command submission.
The current edif code does not keep track of FW IOCB resources. This led
to IOCB queue full on error recovery (I/O timeout). Make use of the
existing code that tracks IOCB resources to prevent over-subscription.
If worker creation fails, nullify the event_thread->worker, so that
msm_drm_uninit() doesn't try accessing invalid memory location. While we
are at it, remove duplicate assignment to the ret variable.
The back porch timings were correct, only the sync offset was wrong.
Correct timing is now reported for 1080i and 576i, but the h offset is
incorrect for 480i for non-obvious reasons.
Fixes: fb10dc451c0f ("drm/vc4: hdmi: Correct HDMI timing registers for interlaced modes") Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com> Link: https://lore.kernel.org/r/20221207-rpi-hvs-crtc-misc-v1-14-1f8e0770798b@cerno.tech Signed-off-by: Maxime Ripard <maxime@cerno.tech> Signed-off-by: Sasha Levin <sashal@kernel.org>
Same as the xRGB8888 formats, HVS5 has managed to swap the colour
channels for the xRGB1555 formats as well. Add the relevant
config for pixel_order_hvs5.
The HVS can change AXI request mode based on how full the COB
FIFOs are.
Until now the vc4 driver has been relying on the firmware to
have set these to sensible values.
With HVS channel 2 now being used for live video, change the
panic mode for all channels to be explicitly set by the driver,
and the same for all channels.
of_find_node_by_phandle() returns a node pointer with refcount incremented,
We should use of_node_put() on it when not needed anymore.
Add missing of_node_put() to avoid refcount leak.
of_irq_find_parent() returns a node pointer with refcount incremented,
We should use of_node_put() on it when not needed anymore.
Add missing of_node_put() to avoid refcount leak.
Add check for the return value of alloc_ordered_workqueue as it may return
NULL pointer and cause NULL pointer dereference in `hdmi_hdcp.c` and
`hdmi_hpd.c`.
A user complained that the ftsteutates driver was displaying
bogus values since its introduction. This happens because the
sensor measurements need to be scaled in order to produce
meaningful results:
- the fan speed needs to be multiplied by 60 since its in RPS
- the temperature is in degrees celsius and needs an offset of 64
- the voltage is in 1/256 of 3.3V
The offical datasheet says the voltage needs to be divided by 256,
but this is likely an off-by-one-error, since even the BIOS
devides by 255 (otherwise 3.3V could not be measured).
The voltage channels additionally need a board-specific multiplier,
however this can be done by the driver since its board-specific.
The reason the missing scaling of measurements is the way Fujitsu
used this driver when it was still out-of-tree. Back then, all
scaling was done in userspace by libsensors, even the generic one.
There was a long-standing bug from a typo that created 2 ARGB1555 and
ABGR1555 pixel format entries. Weston 10 has a sanity check that alerted
me to this issue.
According to the Supported Pixel Data formats table we have the later
entries should have been for Alpha-X instead.
Signed-off-by: Randolph Sapp <rs@ti.com> Fixes: 32a1795f57eecc ("drm/tidss: New driver for TI Keystone platform Display SubSystem") Reviewed-by: Aradhya Bhatia <a-bhatia1@ti.com> Acked-by: Andrew Davis <afd@ti.com> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com> Link: https://patchwork.freedesktop.org/patch/msgid/20221202001803.1765805-1-rs@ti.com Signed-off-by: Sasha Levin <sashal@kernel.org>
The reason is that an OOM happened which triggers the destroy of the
workqueue, however, the workqueue is alloced in the later process,
thus a null-ptr-deref happened. A simple call graph is shown as below:
vkms_init()
vkms_create()
devm_drm_dev_alloc()
__devm_drm_dev_alloc()
devm_drm_dev_init()
devm_add_action_or_reset()
devm_add_action() # an error happened
devm_drm_dev_init_release()
drm_dev_put()
kref_put()
drm_dev_release()
vkms_release()
destroy_workqueue() # null-ptr-deref happened
vkms_modeset_init()
vkms_output_init()
vkms_crtc_init() # where the workqueue get allocated
Fix this by checking if composer_workq is NULL before passing it to
the destroy_workqueue() in vkms_release().
The reason is that the vkms_init() returns without checking the return
value of vkms_create(), and if the vkms_create() failed, the config
allocated at the beginning of vkms_init() is leaked.
vkms_init()
config = kmalloc(...) # config allocated
...
return vkms_create() # vkms_create failed and config is leaked
Fix this problem by checking return value of vkms_create() and free the
config if error happened.
A problem about insmod megachips-stdpxxxx-ge-b850v3-fw.ko failed is
triggered with the following log given:
[ 4497.981497] Error: Driver 'stdp4028-ge-b850v3-fw' is already registered, aborting...
insmod: ERROR: could not insert module megachips-stdpxxxx-ge-b850v3-fw.ko: Device or resource busy
The reason is that stdpxxxx_ge_b850v3_init() returns i2c_add_driver()
directly without checking its return value, if i2c_add_driver() failed,
it returns without calling i2c_del_driver() on the previous i2c driver,
resulting the megachips-stdpxxxx-ge-b850v3-fw can never be installed
later.
A simple call graph is shown as below:
Fix by calling i2c_del_driver() on stdp4028_ge_b850v3_fw_driver when
i2c_add_driver() returns error.
Fixes: fcfa0ddc18ed ("drm/bridge: Drivers for megachips-stdpxxxx-ge-b850v3-fw (LVDS-DP++)") Signed-off-by: Yuan Can <yuancan@huawei.com> Reviewed-by: Andrzej Hajda <andrzej.hajda@intel.com> Tested-by: Ian Ray <ian.ray@ge.com> Signed-off-by: Robert Foss <robert.foss@linaro.org> Link: https://patchwork.freedesktop.org/patch/msgid/20221108091226.114524-1-yuancan@huawei.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Freescale/NXP i.MX LCDIF and eLCDIF LCD controllers are only present on
Freescale/NXP i.MX SoCs. Hence add a dependency on ARCH_MXS ||
ARCH_MXC, to prevent asking the user about this driver when configuring
a kernel without Freescale/NXP i.MX support.
The datasheet specifies a delay of 10 milliseconds, but the current
driver only waits for 1 ms. Fix this to make sure the initialization
sequence meets the spec.
Fixes: ceb515ba29ba ("drm/bridge: ti-sn65dsi83: Add TI SN65DSI83 and SN65DSI84 driver") Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de> Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com> Signed-off-by: Robert Foss <robert.foss@linaro.org> Link: https://patchwork.freedesktop.org/patch/msgid/20221122081219.20143-1-frieder@fris.de Signed-off-by: Sasha Levin <sashal@kernel.org>
As of commit eae06120f1974e1a ("drm: refuse ADDFB2 ioctl for broken
bigendian drivers"), drivers must set the
quirk_addfb_prefer_host_byte_order quirk to make the drm_mode_addfb()
compat code work correctly on big-endian machines.
While that works fine for big-endian XRGB8888 and ARGB8888, which are
mapped to the existing little-endian BGRX8888 and BGRA8888 formats, it
does not work for big-endian XRGB1555 and RGB565, as the latter are not
listed in the format database.
Fix this by adding the missing formats. Limit this to big-endian
platforms, as there is currently no need to support these formats on
little-endian platforms.
drmm_mode_config_init() will call drm_mode_create_standard_properties()
and won't check the ret value. When drm_mode_create_standard_properties()
failed due to alloc, property will be a NULL pointer and may causes the
null-ptr-deref. Fix the null-ptr-deref by adding the ret value check.
Found null-ptr-deref while testing insert module bochs:
general protection fault, probably for non-canonical address
0xdffffc000000000c: 0000 [#1] SMP KASAN PTI
KASAN: null-ptr-deref in range [0x0000000000000060-0x0000000000000067]
CPU: 3 PID: 249 Comm: modprobe Not tainted 6.1.0-rc1+ #364
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.15.0-0-g2dd4b9b3f840-prebuilt.qemu.org 04/01/2014
RIP: 0010:drm_object_attach_property+0x73/0x3c0 [drm]
Call Trace:
<TASK>
__drm_connector_init+0xb6c/0x1100 [drm]
bochs_pci_probe.cold.11+0x4cb/0x7fe [bochs]
pci_device_probe+0x17d/0x340
really_probe+0x1db/0x5d0
__driver_probe_device+0x1e7/0x250
driver_probe_device+0x4a/0x120
__driver_attach+0xcd/0x2c0
bus_for_each_dev+0x11a/0x1b0
bus_add_driver+0x3d7/0x500
driver_register+0x18e/0x320
do_one_initcall+0xc4/0x3e0
do_init_module+0x1b4/0x630
load_module+0x5dca/0x7230
__do_sys_finit_module+0x100/0x170
do_syscall_64+0x3f/0x90
entry_SYSCALL_64_after_hwframe+0x63/0xcd
RIP: 0033:0x7ff65af9f839
When devlink instance is put into network namespace and that network
namespace gets deleted, devlink instance is moved back into init_ns.
This is done as a part of cleanup_net() routine. Since cleanup_net()
is called asynchronously from workqueue, there is no guarantee that
the devlink instance move is done after "ip netns del" returns.
So fix this race by making sure that the devlink instance is present
before any other operation.
Reported-by: Amir Tzin <amirtz@nvidia.com> Fixes: b74c37fd35a2 ("selftests: netdevsim: add tests for devlink reload with resources") Signed-off-by: Jiri Pirko <jiri@nvidia.com> Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com> Link: https://lore.kernel.org/r/20230220132336.198597-1-jiri@resnulli.us Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Usage of `set -e` before executing a command causes immediate exit
on failure, without cleanup up the resources allocated at setup.
This can affect the next tests that use the same resources,
leading to a chain of failures.
A simple fix is to always call cleanup function when the script exists.
This approach is already used by other existing tests.
Fixes: 1056691b2680 ("selftests: fib_tests: Make test results more verbose") Signed-off-by: Roxana Nicolescu <roxana.nicolescu@canonical.com> Link: https://lore.kernel.org/r/20230220110400.26737-2-roxana.nicolescu@canonical.com Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When the bcmgenet_mii_config() code was refactored it was missed
that the LED control for the MoCA interface got overwritten by
the port_ctrl value. Its previous programming is restored here.
Fixes: 4f8d81b77e66 ("net: bcmgenet: Refactor register access in bcmgenet_mii_config") Signed-off-by: Doug Berger <opendmb@gmail.com> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
When a file descriptor of pppol2tp socket is passed as file descriptor
of UDP socket, a recursive deadlock occurs in l2tp_tunnel_register().
This situation is reproduced by the following program:
int main(void)
{
int sock;
struct sockaddr_pppol2tp addr;
This patch fixes the issue by getting/creating the tunnel before
locking the pppol2tp socket.
Fixes: 0b2c59720e65 ("l2tp: close all race conditions in l2tp_tunnel_register()") Cc: Cong Wang <cong.wang@bytedance.com> Signed-off-by: Shigeru Yoshida <syoshida@redhat.com> Reviewed-by: Guillaume Nault <gnault@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fixes: 3327a9c46352 ("selftests: add functionals test for UDP GRO") Suggested-by: Eric Dumazet <edumazet@google.com> Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
When support for the interrupt controller was added with a5042de2688d,
we forgot to update the flags to be set to contain IRQ_LEVEL. While the
flow handler is correct, the output from /proc/interrupts does not show
such interrupts as being level triggered when they are, correct that.
When support for the level triggered interrupt controller flavor was
added with c0ca7262088e, we forgot to update the flags to be set to
contain IRQ_LEVEL. While the flow handler is correct, the output from
/proc/interrupts does not show such interrupts as being level triggered
when they are, correct that.
Fixes: c0ca7262088e ("irqchip/brcmstb-l2: Add support for the BCM7271 L2 controller") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org> Signed-off-by: Marc Zyngier <maz@kernel.org> Link: https://lore.kernel.org/r/20221216230934.2478345-2-f.fainelli@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
KPROBE program's user-facing context type is defined as typedef
bpf_user_pt_regs_t. This leads to a problem when trying to passing
kprobe/uprobe/usdt context argument into global subprog, as kernel
always strip away mods and typedefs of user-supplied type, but takes
expected type from bpf_ctx_convert as is, which causes mismatch.
Current way to work around this is to define a fake struct with the same
name as expected typedef:
This patch fixes the issue by resolving expected type, if it's not
a struct. It still leaves the above work-around working for backwards
compatibility.
Move the supply for cf->data[3] (bit stream position of CAN error), in
case of a bus- or protocol-error, outside of the "switch (ecc &
SJA1000_ECC_MASK){}"-statement, because this bit stream position is
independent of the error type.
Fixes: 96d8e90382dc ("can: Add driver for esd CAN-USB/2 device") Signed-off-by: Frank Jungclaus <frank.jungclaus@esd.eu> Link: https://lore.kernel.org/all/20230216190450.3901254-2-frank.jungclaus@esd.eu Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
The commit 74c8e6bffbe1 ("driver core: Add __alloc_size hint to devm
allocators") exposes a panic "BRK handler: Fatal exception" on the
hi3660_thermal_probe funciton.
This is because the function allocates memory for only one
sensors array entry, but tries to fill up a second one.
The value of last_rate in ieee80211_sta_rx_stats is degraded from u32 to
u16 after being assigned to rate variable, which causes information loss
in STA_STATS_FIELD_TYPE and later bitfields.
In crypto4xx_cipher_done, we should be unmapping the dst page, not
mapping it.
This was flagged by a sparse warning about the unused addr variable.
While we're at it, also fix a sparse warning regarding the unused
ctx variable in crypto4xx_ahash_done (by actually using it).
Fixes: 049359d65527 ("crypto: amcc - Add crypt4xx driver") Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Tested-by: Christian Lamparter <chunkeey@gmail.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
Apply commit 7592b79ba4a9 ("ACPI: resource: do IRQ override on XMG Core 15")
override for all vendors using this mainboard.
Signed-off-by: Werner Sembach <wse@tuxedocomputers.com> Fixes: 9946e39fe8d0 ("ACPI: resource: skip IRQ override on AMD Zen platforms") Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fix a regression introduced by commit 9946e39fe8d0 ("ACPI: resource: skip
IRQ override on AMD Zen platforms") on MAINGEAR Vector Pro 2 systems, which
causes the built-in keyboard to not work. This restores the functionality
by adding an IRQ override.
No other IRQs were being overridden before, so this should be all that is
needed for these systems. I have personally tested this on the 15" model
(MG-VCP2-15A3070T), and I have confirmation that the issue is present on
the 17" model (MG-VCP2-17A3070T).
Fixes: 9946e39fe8d0 ("ACPI: resource: skip IRQ override on AMD Zen platforms") Signed-off-by: Adam Niederer <adam.niederer@gmail.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
make: *** No rule to make target '/linux-build//ima_setup.sh', needed by 'ima_setup.sh'. Stop.
The culprit is the rule that defines convenient shorthands like
"make test_progs", which builds $(OUTPUT)/test_progs. These shorthands
make sense only for binaries that are built though; scripts that live
in the source tree do not end up in $(OUTPUT).
Therefore drop $(TEST_PROGS) and $(TEST_PROGS_EXTENDED) from the rule.
The issue exists for a while, but it became a problem only after commit d68ae4982cb7 ("selftests/bpf: Install all required files to run selftests"),
which added dependencies on these scripts.
Similarly to commit 022eb8ae8b5e ("ARM: 8938/1: kernel: initialize
broadcast hrtimer based clock event device"), RISC-V needs to initiate
hrtimer based broadcast clock event device before C3STOP can be used.
Otherwise, the introduction of C3STOP for the RISC-V arch timer in
commit 232ccac1bd9b ("clocksource/drivers/riscv: Events are stopped
during CPU suspend") leaves us without any broadcast timer registered.
This prevents the kernel from entering oneshot mode, which breaks timer
behaviour, for example clock_nanosleep().
A test app that sleeps each cpu for 6, 5, 4, 3 ms respectively, HZ=250
& C3STOP enabled, the sleep times are rounded up to the next jiffy:
== CPU: 1 == == CPU: 2 == == CPU: 3 == == CPU: 4 ==
Mean: 7.974992 Mean: 7.976534 Mean: 7.962591 Mean: 3.952179
Std Dev: 0.154374 Std Dev: 0.156082 Std Dev: 0.171018 Std Dev: 0.076193
Hi: 9.472000 Hi: 10.495000 Hi: 8.864000 Hi: 4.736000
Lo: 6.087000 Lo: 6.380000 Lo: 4.872000 Lo: 3.403000
Samples: 521 Samples: 521 Samples: 521 Samples: 521
Link: https://lore.kernel.org/linux-riscv/YzYTNQRxLr7Q9JR0@spud/ Fixes: 232ccac1bd9b ("clocksource/drivers/riscv: Events are stopped during CPU suspend") Suggested-by: Samuel Holland <samuel@sholland.org> Signed-off-by: Conor Dooley <conor.dooley@microchip.com> Signed-off-by: Anup Patel <apatel@ventanamicro.com> Reviewed-by: Samuel Holland <samuel@sholland.org> Acked-by: Palmer Dabbelt <palmer@rivosinc.com> Link: https://lore.kernel.org/r/20230103141102.772228-2-apatel@ventanamicro.com Signed-off-by: Daniel Lezcano <daniel.lezcano@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When CONFIG_PROC_FS is not set, there is a build error for an unused
function. Make PROC_HARDWARE depend on PROC_FS to prevent this error.
In file included from ../arch/m68k/kernel/setup.c:3:
../arch/m68k/kernel/setup_mm.c:477:12: error: 'hardware_proc_show' defined but not used [-Werror=unused-function]
477 | static int hardware_proc_show(struct seq_file *m, void *v)
| ^~~~~~~~~~~~~~~~~~
Use the akcipher_request_complete helper instead of calling the
completion function directly. In fact the previous code was buggy
in that EINPROGRESS was never passed back to the original caller.
rds_rm_zerocopy_callback() uses list_add_tail() with swapped
arguments. This links the list head with the new entry, losing
the references to the remaining part of the list.
Fixes: 9426bbc6de99 ("rds: use list structure to track information for zerocopy completion notification") Suggested-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Pietro Borrello <borrello@diag.uniroma1.it> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The code assumes that everything that comes after nlmsgerr are nlattrs.
When calculating their size, it does not account for the initial
nlmsghdr. This may lead to accessing uninitialized memory.
Since commit 159491f3b509 ("s390/ap: rework assembler functions to use
unions for in/out register variables") the function ap_qact() tries to
grab the status from the wrong part of the register. Thus we always end
up with zeros. Which is wrong, among others, because we detect failures
via status.response_code.
Signed-off-by: Halil Pasic <pasic@linux.ibm.com> Reported-by: Harald Freudenberger <freude@linux.ibm.com> Fixes: 159491f3b509 ("s390/ap: rework assembler functions to use unions for in/out register variables") Reviewed-by: Harald Freudenberger <freude@linux.ibm.com> Signed-off-by: Heiko Carstens <hca@linux.ibm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
There function ap_aqic() tries to grab the status from the
wrong part of the register. Thus we always end up with
zeros. Which is wrong, among others, because we detect
failures via status.response_code.
Signed-off-by: Halil Pasic <pasic@linux.ibm.com> Reported-by: Janosch Frank <frankja@linux.ibm.com> Fixes: 159491f3b509 ("s390/ap: rework assembler functions to use unions for in/out register variables") Reviewed-by: Harald Freudenberger <freude@linux.ibm.com> Signed-off-by: Heiko Carstens <hca@linux.ibm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Bluetooth controller attached via the UART is handled by the serdev driver.
Get the wakeup status from the device handle through serdev, instead of the
parent path.
This fixes all instances of which requires to allocate a buffer calling
alloc_skb which may release the chan lock and reacquire later which
makes it possible that the chan is disconnected in the meantime.
Fixes: a6a5568c03c4 ("Bluetooth: Lock the L2CAP channel when sending") Reported-by: Alexander Coffin <alex.coffin@matician.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Since commit ff9fb72bc077 ("debugfs: return error values,
not NULL") changed return value of debugfs_rename() in
error cases from %NULL to %ERR_PTR(-ERROR), we should
also check error values instead of NULL.
sock_init_data() assumes that the `struct socket` passed in input is
contained in a `struct socket_alloc` allocated with sock_alloc().
However, tap_open() passes a `struct socket` embedded in a `struct
tap_queue` allocated with sk_alloc().
This causes a type confusion when issuing a container_of() with
SOCK_INODE() in sock_init_data() which results in assigning a wrong
sk_uid to the `struct sock` in input.
On default configuration, the type confused field overlaps with
padding bytes between `int vnet_hdr_sz` and `struct tap_dev __rcu
*tap` in `struct tap_queue`, which makes the uid of all tap sockets 0,
i.e., the root one.
Fix the assignment by using sock_init_data_uid().
Fixes: 86741ec25462 ("net: core: Add a UID field to struct sock.") Signed-off-by: Pietro Borrello <borrello@diag.uniroma1.it> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
sock_init_data() assumes that the `struct socket` passed in input is
contained in a `struct socket_alloc` allocated with sock_alloc().
However, tun_chr_open() passes a `struct socket` embedded in a `struct
tun_file` allocated with sk_alloc().
This causes a type confusion when issuing a container_of() with
SOCK_INODE() in sock_init_data() which results in assigning a wrong
sk_uid to the `struct sock` in input.
On default configuration, the type confused field overlaps with the
high 4 bytes of `struct tun_struct __rcu *tun` of `struct tun_file`,
NULL at the time of call, which makes the uid of all tun sockets 0,
i.e., the root one.
Fix the assignment by using sock_init_data_uid().
Fixes: 86741ec25462 ("net: core: Add a UID field to struct sock.") Signed-off-by: Pietro Borrello <borrello@diag.uniroma1.it> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Add sock_init_data_uid() to explicitly initialize the socket uid.
To initialise the socket uid, sock_init_data() assumes a the struct
socket* sock is always embedded in a struct socket_alloc, used to
access the corresponding inode uid. This may not be true.
Examples are sockets created in tun_chr_open() and tap_open().
Fixes: 86741ec25462 ("net: core: Add a UID field to struct sock.") Signed-off-by: Pietro Borrello <borrello@diag.uniroma1.it> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit b9ff81003cf1 ("s390/vmem: cleanup empty page tables") introduced
empty page tables cleanup in vmem code, but when the kernel is built
with KASAN enabled the code has no effect due to wrong KASAN shadow
memory intersection condition, which effectively ignores any memory
range below KASAN shadow. Fix intersection condition to make code
work as anticipated.
Currently if for some reason sclp_early_read_info() fails,
sclp_early_get_memsize() will not set max_physmem_end and it
will stay uninitialized. Any garbage value other than 0 will lead
to detect_memory() taking wrong path or returning a garbage value
as max_physmem_end. To avoid that simply initialize max_physmem_end.
of_irq_find_parent() returns a node pointer with refcount incremented,
We should use of_node_put() on it when not needed anymore.
Add missing of_node_put() to avoid refcount leak.
Fixes: cd844b0715ce ("irqchip/ti-sci-intr: Add support for Interrupt Router driver") Signed-off-by: Miaoqian Lin <linmq006@gmail.com> Signed-off-by: Marc Zyngier <maz@kernel.org> Link: https://lore.kernel.org/r/20230102085611.3955984-1-linmq006@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
of_irq_find_parent() returns a node pointer with refcount incremented,
We should use of_node_put() on it when not needed anymore.
Add missing of_node_put() to avoid refcount leak.
Fixes: a68a63cb4dfc ("irqchip/irq-mvebu-gicp: Add new driver for Marvell GICP") Signed-off-by: Miaoqian Lin <linmq006@gmail.com> Signed-off-by: Marc Zyngier <maz@kernel.org> Link: https://lore.kernel.org/r/20230102084208.3951758-1-linmq006@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
of_irq_find_parent() returns a node pointer with refcount incremented,
We should use of_node_put() on it when not needed anymore.
Add missing of_node_put() to avoid refcount leak.
Fixes: e6b78f2c3e14 ("irqchip: Add the Alpine MSIX interrupt controller") Signed-off-by: Miaoqian Lin <linmq006@gmail.com> Signed-off-by: Marc Zyngier <maz@kernel.org> Link: https://lore.kernel.org/r/20230102082811.3947760-1-linmq006@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
of_irq_find_parent() returns a node pointer with refcount incremented,
We should use of_node_put() on it when not needed anymore.
Add missing of_node_put() to avoid refcount leak.
Fixes: f8410e626569 ("irqchip: Add IRQCHIP_PLATFORM_DRIVER_BEGIN/END and IRQCHIP_MATCH helper macros") Signed-off-by: Miaoqian Lin <linmq006@gmail.com> Signed-off-by: Marc Zyngier <maz@kernel.org> Link: https://lore.kernel.org/r/20230102121318.3990586-1-linmq006@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Disable cpu dynamically:
$ echo 0 > /sys/devices/system/cpu/cpuX/online
If one cpu is offline, perf_event_open will return ENODEV.
To fix this issue:
* check value returned and skip offline cpu.
* close pmu_fd immediately on error path, avoid fd leaking.
Fixes: 47c09d6a9f67 ("bpftool: Introduce "prog profile" command") Signed-off-by: Tonghao Zhang <tong@infragraf.org> Cc: Quentin Monnet <quentin@isovalent.com> Cc: Alexei Starovoitov <ast@kernel.org> Cc: Daniel Borkmann <daniel@iogearbox.net> Cc: Andrii Nakryiko <andrii@kernel.org> Cc: Martin KaFai Lau <martin.lau@linux.dev> Cc: Song Liu <song@kernel.org> Cc: Yonghong Song <yhs@fb.com> Cc: John Fastabend <john.fastabend@gmail.com> Cc: KP Singh <kpsingh@kernel.org> Cc: Stanislav Fomichev <sdf@google.com> Cc: Hao Luo <haoluo@google.com> Cc: Jiri Olsa <jolsa@kernel.org> Acked-by: John Fastabend <john.fastabend@gmail.com> Link: https://lore.kernel.org/r/20230202131701.29519-1-tong@infragraf.org Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Perform a cache flush on the SEV-ES TMR memory after allocation to prevent
any possibility of the firmware encountering an error should dirty cache
lines be present. Use clflush_cache_range() to flush the SEV-ES TMR memory.
Fixes: 97f9ac3db661 ("crypto: ccp - Add support for SEV-ES to the PSP driver") Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
Create a helper function sev_fw_alloc() which can be used to allocate
aligned memory regions for use by the PSP firmware. Currently only used
for the SEV-ES TMR region but will be used for the SEV_INIT_EX NV memory
region.
Signed-off-by: Peter Gonda <pgonda@google.com> Reviewed-by: Marc Orr <marcorr@google.com> Acked-by: David Rientjes <rientjes@google.com> Acked-by: Brijesh Singh <brijesh.singh@amd.com> Cc: Tom Lendacky <thomas.lendacky@amd.com> Cc: Brijesh Singh <brijesh.singh@amd.com> Cc: Marc Orr <marcorr@google.com> Cc: Joerg Roedel <jroedel@suse.de> Cc: Herbert Xu <herbert@gondor.apana.org.au> Cc: David Rientjes <rientjes@google.com> Cc: John Allen <john.allen@amd.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: Paolo Bonzini <pbonzini@redhat.com> Cc: linux-crypto@vger.kernel.org Cc: linux-kernel@vger.kernel.org Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Stable-dep-of: 46a334a98f58 ("crypto: ccp - Flush the SEV-ES TMR memory before giving it to firmware") Signed-off-by: Sasha Levin <sashal@kernel.org>
led_put() is used to "undo" a successful of_led_get() call,
of_led_get() uses class_find_device_by_of_node() which returns
a reference to the device which must be free-ed with put_device()
when the caller is done with it.
Add a put_device() call to led_put() to free the reference returned
by class_find_device_by_of_node().
And also add a put_device() in the error-exit case of try_module_get()
failing.
Fixes: 699a8c7c4bd3 ("leds: Add of_led_get() and led_put()") Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Lee Jones <lee@kernel.org> Link: https://lore.kernel.org/r/20230120114524.408368-2-hdegoede@redhat.com Signed-off-by: Sasha Levin <sashal@kernel.org>
As it is xts only handles the special return value of EINPROGRESS,
which means that in all other cases it will free data related to the
request.
However, as the caller of xts may specify MAY_BACKLOG, we also need
to expect EBUSY and treat it in the same way. Otherwise backlogged
requests will trigger a use-after-free.
Fixes: 8083b1bf8163 ("crypto: xts - add support for ciphertext stealing") Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Acked-by: Ard Biesheuvel <ardb@kernel.org> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
The kernel caches each CPU's feature bits at boot in an x86_capability[]
structure. However, the capabilities in the BSP's copy can be turned off
as a result of certain command line parameters or configuration
restrictions, for example the SGX bit. This can cause a mismatch when
comparing the values before and after the microcode update.
Another example is X86_FEATURE_SRBDS_CTRL which gets added only after
microcode update:
and which proves for a gazillionth time that late loading is a bad bad
idea.
microcode_check() is called after an update to report any previously
cached CPUID bits which might have changed due to the update.
Therefore, store the cached CPU caps before the update and compare them
with the CPU caps after the microcode update has succeeded.
Thus, the comparison is done between the CPUID *hardware* bits before
and after the upgrade instead of using the cached, possibly runtime
modified values in BSP's boot_cpu_data copy.
As a result, false warnings about CPUID bits changes are avoided.
Print both old and new versions of microcode after a reload is complete
because knowing the previous microcode version is sometimes important
from a debugging perspective.
[ bp: Massage commit message. ]
Signed-off-by: Ashok Raj <ashok.raj@intel.com> Signed-off-by: Borislav Petkov <bp@suse.de> Acked-by: Tony Luck <tony.luck@intel.com> Link: https://lore.kernel.org/r/20220829181030.722891-1-ashok.raj@intel.com
Stable-dep-of: c0dd9245aa9e ("x86/microcode: Check CPU capabilities after late microcode update correctly") Signed-off-by: Sasha Levin <sashal@kernel.org>
In the error path after calling dev_set_name(), the device
name is leaked. To fix this, calling dev_set_name() before
device_register(), and call put_device() if it returns error.
All the resources is released in powercap_release(), so it
can return from powercap_register_zone() directly.
Fixes: 75d2364ea0ca ("PowerCap: Add class driver") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / thirdparty / kernel / stable.git / log
