If CONFIG_DRM_AUX_HPD_BRIDGE is not enabled, the aux-bridge.h header
provides a stub for the bridge's functions. Correct the arguments list
of one of those stubs to match the argument list of the non-stubbed
function.
Fixes: e5ca263508f7 ("drm/bridge: aux-hpd: separate allocation and registration") Reported-by: kernel test robot <lkp@intel.com> Cc: stable <stable@kernel.org> Closes: https://lore.kernel.org/oe-kbuild-all/202405110428.TMCfb1Ut-lkp@intel.com/ Cc: Johan Hovold <johan+linaro@kernel.org> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Reviewed-by: Johan Hovold <johan+linaro@kernel.org> Link: https://lore.kernel.org/r/20240511-fix-aux-hpd-stubs-v1-1-98dae71dfaec@linaro.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need to first free the IRQ before calling of_dma_controller_free().
Otherwise we could get an interrupt and schedule a tasklet while
removing the DMA controller.
Fixes: 0e3b67b348b8 ("dmaengine: Add support for the Analog Devices AXI-DMAC DMA controller") Cc: stable@kernel.org Signed-off-by: Nuno Sa <nuno.sa@analog.com> Link: https://lore.kernel.org/r/20240328-axi-dmac-devm-probe-v3-1-523c0176df70@analog.com Signed-off-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove wrong mask on subsys_vendor_id. Both the Vendor ID and Subsystem
Vendor ID are u16 variables and are written to a u32 register of the
controller. The Subsystem Vendor ID was always 0 because the u16 value
was masked incorrectly with GENMASK(31,16) resulting in all lower 16
bits being set to 0 prior to the shift.
Remove both masks as they are unnecessary and set the register correctly
i.e., the lower 16-bits are the Vendor ID and the upper 16-bits are the
Subsystem Vendor ID.
This is documented in the RK3399 TRM section 17.6.7.1.17
[kwilczynski: removed unnecesary newline] Fixes: cf590b078391 ("PCI: rockchip: Add EP driver for Rockchip PCIe controller") Link: https://lore.kernel.org/linux-pci/20240403144508.489835-1-rick.wertenbroek@gmail.com Signed-off-by: Rick Wertenbroek <rick.wertenbroek@gmail.com> Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Damien Le Moal <dlemoal@kernel.org> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dm-integrity could set discard_granularity lower than the logical block
size. This could result in failures when sending discard requests to
dm-integrity.
After commit "ocfs2: return real error code in ocfs2_dio_wr_get_block",
fstests/generic/300 become from always failed to sometimes failed:
========================================================================
[ 473.293420 ] run fstests generic/300
[ 475.296983 ] JBD2: Ignoring recovery information on journal
[ 475.302473 ] ocfs2: Mounting device (253,1) on (node local, slot 0) with ordered data mode.
[ 494.290998 ] OCFS2: ERROR (device dm-1): ocfs2_change_extent_flag: Owner 5668 has an extent at cpos 78723 which can no longer be found
[ 494.291609 ] On-disk corruption discovered. Please run fsck.ocfs2 once the filesystem is unmounted.
[ 494.292018 ] OCFS2: File system is now read-only.
[ 494.292224 ] (kworker/19:11,2628,19):ocfs2_mark_extent_written:5272 ERROR: status = -30
[ 494.292602 ] (kworker/19:11,2628,19):ocfs2_dio_end_io_write:2374 ERROR: status = -3
fio: io_u error on file /mnt/scratch/racer: Read-only file system: write offset=460849152, buflen=131072
=========================================================================
In __blockdev_direct_IO, ocfs2_dio_wr_get_block is called to add unwritten
extents to a list. extents are also inserted into extent tree in
ocfs2_write_begin_nolock. Then another thread call fallocate to puch a
hole at one of the unwritten extent. The extent at cpos was removed by
ocfs2_remove_extent(). At end io worker thread, ocfs2_search_extent_list
found there is no such extent at the cpos.
In most filesystems, fallocate is not compatible with racing with AIO+DIO,
so fix it by adding to wait for all dio before fallocate/punch_hole like
ext4.
Link: https://lkml.kernel.org/r/20240408082041.20925-3-glass.su@suse.com Fixes: b25801038da5 ("ocfs2: Support xfs style space reservation ioctls") Signed-off-by: Su Yue <glass.su@suse.com> Reviewed-by: Joseph Qi <joseph.qi@linux.alibaba.com> Cc: Changwei Ge <gechangwei@live.cn> Cc: Gang He <ghe@suse.com> Cc: Joel Becker <jlbec@evilplan.org> Cc: Jun Piao <piaojun@huawei.com> Cc: Junxiao Bi <junxiao.bi@oracle.com> Cc: Mark Fasheh <mark@fasheh.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The default atime related mount option is '-o realtime' which means file
atime should be updated if atime <= ctime or atime <= mtime. atime should
be updated in the following scenario, but it is not:
==========================================================
$ rm /mnt/testfile;
$ echo test > /mnt/testfile
$ stat -c "%X %Y %Z" /mnt/testfile 171188164617118816461711881646
$ sleep 5
$ cat /mnt/testfile > /dev/null
$ stat -c "%X %Y %Z" /mnt/testfile 171188164617118816461711881646
==========================================================
And the reason the atime in the test is not updated is that ocfs2 calls
ktime_get_real_ts64() in __ocfs2_mknod_locked during file creation. Then
inode_set_ctime_current() is called in inode_set_ctime_current() calls
ktime_get_coarse_real_ts64() to get current time.
ktime_get_real_ts64() is more accurate than ktime_get_coarse_real_ts64().
In my test box, I saw ctime set by ktime_get_coarse_real_ts64() is less
than ktime_get_real_ts64() even ctime is set later. The ctime of the new
inode is smaller than atime.
ktime_get_real_ts64 <------- set atime,ctime,mtime, more accurate
ocfs2_populate_inode
...
ocfs2_init_acl
ocfs2_acl_set_mode
inode_set_ctime_current
current_time
ktime_get_coarse_real_ts64 <-------less accurate
ocfs2_file_read_iter
ocfs2_inode_lock_atime
ocfs2_should_update_atime
atime <= ctime ? <-------- false, ctime < atime due to accuracy
So here call ktime_get_coarse_real_ts64 to set inode time coarser while
creating new files. It may lower the accuracy of file times. But it's
not a big deal since we already use coarse time in other places like
ocfs2_update_inode_atime and inode_set_ctime_current.
Link: https://lkml.kernel.org/r/20240408082041.20925-5-glass.su@suse.com Fixes: c62c38f6b91b ("ocfs2: replace CURRENT_TIME macro") Signed-off-by: Su Yue <glass.su@suse.com> Reviewed-by: Joseph Qi <joseph.qi@linux.alibaba.com> Cc: Mark Fasheh <mark@fasheh.com> Cc: Joel Becker <jlbec@evilplan.org> Cc: Junxiao Bi <junxiao.bi@oracle.com> Cc: Changwei Ge <gechangwei@live.cn> Cc: Gang He <ghe@suse.com> Cc: Jun Piao <piaojun@huawei.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
transaction id should be updated in ocfs2_unlink and ocfs2_link.
Otherwise, inode link will be wrong after journal replay even fsync was
called before power failure:
=======================================================================
$ touch testdir/bar
$ ln testdir/bar testdir/bar_link
$ fsync testdir/bar
$ stat -c %h $SCRATCH_MNT/testdir/bar
1
$ stat -c %h $SCRATCH_MNT/testdir/bar
1
=======================================================================
Link: https://lkml.kernel.org/r/20240408082041.20925-4-glass.su@suse.com Fixes: ccd979bdbce9 ("[PATCH] OCFS2: The Second Oracle Cluster Filesystem") Signed-off-by: Su Yue <glass.su@suse.com> Reviewed-by: Joseph Qi <joseph.qi@linux.alibaba.com> Cc: Changwei Ge <gechangwei@live.cn> Cc: Gang He <ghe@suse.com> Cc: Joel Becker <jlbec@evilplan.org> Cc: Jun Piao <piaojun@huawei.com> Cc: Junxiao Bi <junxiao.bi@oracle.com> Cc: Mark Fasheh <mark@fasheh.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jiri reported that the current kexec_dprintk() always prints out debugging
message whenever kexec/kdmmp loading is triggered. That is not wanted.
The debugging message is supposed to be printed out when 'kexec -s -d' is
specified for kexec/kdump loading.
After investigating, the reason is the current kexec_dprintk() takes
printk(KERN_INFO) or printk(KERN_DEBUG) depending on whether '-d' is
specified. However, distros usually have defaulg log level like below:
[~]# cat /proc/sys/kernel/printk
7 4 1 7
So, even though '-d' is not specified, printk(KERN_DEBUG) also always
prints out. I thought printk(KERN_DEBUG) is equal to pr_debug(), it's
not.
Fix it by changing to use pr_info() instead which are expected to work.
Link: https://lkml.kernel.org/r/20240409042238.1240462-1-bhe@redhat.com Fixes: cbc2fe9d9cb2 ("kexec_file: add kexec_file flag to control debug printing") Signed-off-by: Baoquan He <bhe@redhat.com> Reported-by: Jiri Slaby <jirislaby@kernel.org> Closes: https://lore.kernel.org/all/4c775fca-5def-4a2d-8437-7130b02722a2@kernel.org Reviewed-by: Dave Young <dyoung@redhat.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While taking a kernel core dump with makedumpfile on a larger system,
softlockup messages often appear.
While softlockup warnings can be harmless, they can also interfere with
things like RCU freeing memory, which can be problematic when the kdump
kexec image is configured with as little memory as possible.
Avoid the softlockup, and give things like work items and RCU a chance to
do their thing during __read_vmcore by adding a cond_resched.
Link: https://lkml.kernel.org/r/20240507091858.36ff767f@imladris.surriel.com Signed-off-by: Rik van Riel <riel@surriel.com> Acked-by: Baoquan He <bhe@redhat.com> Cc: Dave Young <dyoung@redhat.com> Cc: Vivek Goyal <vgoyal@redhat.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 'NFS error' NFSERR_OPNOTSUPP is not described by any of the official
NFS related RFCs, but appears to have snuck into some older .x files for
NFSv2.
Either way, it is not in RFC1094, RFC1813 or any of the NFSv4 RFCs, so
should not be returned by the knfsd server, and particularly not by the
"LOOKUP" operation.
Instead, let's return NFSERR_STALE, which is more appropriate if the
filesystem encodes the filehandle as FILEID_INVALID.
'nr' member of struct spmi_controller, which serves as an identifier
for the controller/bus. This value is a dynamic ID assigned in
spmi_controller_alloc, and overriding it from the driver results in an
ida_free error "ida_free called for id=xx which is not allocated".
Coverity spotted that event_msg is controlled by user-space,
event_msg->event_data.event is passed to event_deliver() and used
as an index without sanitization.
This change ensures that the event index is sanitized to mitigate any
possibility of speculative information leaks.
This bug was discovered and resolved using Coverity Static Analysis
Security Testing (SAST) by Synopsys, Inc.
kthread creation may possibly fail inside race_signal_callback(). In
such a case stop the already started threads, put the already taken
references to them and return with error code.
Found by Linux Verification Center (linuxtesting.org).
Fixes: 2989f6451084 ("dma-buf: Add selftests for dma-fence") Cc: stable@vger.kernel.org Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru> Reviewed-by: T.J. Mercier <tjmercier@google.com> Link: https://patchwork.freedesktop.org/patch/msgid/20240522181308.841686-1-pchelkin@ispras.ru Signed-off-by: Christian König <christian.koenig@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
sk_psock_get will return NULL if the refcount of psock has gone to 0, which
will happen when the last call of sk_psock_put is done. However,
sk_psock_drop may not have finished yet, so the close callback will still
point to sock_map_close despite psock being NULL.
This can be reproduced with a thread deleting an element from the sock map,
while the second one creates a socket, adds it to the map and closes it.
Use sk_psock, which will only check that the pointer is not been set to
NULL yet, which should only happen after the callbacks are restored. If,
then, a reference can still be gotten, we may call sk_psock_stop and cancel
psock->work.
As suggested by Paolo Abeni, reorder the condition so the control flow is
less convoluted.
After that change, the reproducer does not trigger the WARN_ON_ONCE
anymore.
Suggested-by: Paolo Abeni <pabeni@redhat.com> Reported-by: syzbot+07a2e4a1a57118ef7355@syzkaller.appspotmail.com Closes: https://syzkaller.appspot.com/bug?extid=07a2e4a1a57118ef7355 Fixes: aadb2bb83ff7 ("sock_map: Fix a potential use-after-free in sock_map_close()") Fixes: 5b4a79ba65a1 ("bpf, sockmap: Don't let sock_map_{close,destroy,unhash} call itself") Cc: stable@vger.kernel.org Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@igalia.com> Acked-by: Jakub Sitnicki <jakub@cloudflare.com> Link: https://lore.kernel.org/r/20240524144702.1178377-1-cascardo@igalia.com Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 7627a0edef54 ("ata: ahci: Drop low power policy board type")
dropped the board_ahci_low_power board type, and instead enables LPM if:
-The AHCI controller reports that it supports LPM (Partial/Slumber), and
-CONFIG_SATA_MOBILE_LPM_POLICY != 0, and
-The port is not defined as external in the per port PxCMD register, and
-The port is not defined as hotplug capable in the per port PxCMD
register.
Partial and Slumber LPM states can either be initiated by HIPM or DIPM.
For HIPM (host initiated power management) to get enabled, both the AHCI
controller and the drive have to report that they support HIPM.
For DIPM (device initiated power management) to get enabled, only the
drive has to report that it supports DIPM. However, the HBA will reject
device requests to enter LPM states which the HBA does not support.
The problem is that AMD Radeon S3 SSD drives do not handle low power modes
correctly. The problem was most likely not seen before because no one
had used this drive with a AHCI controller with LPM enabled.
Add a quirk so that we do not enable LPM for this drive, since we see
command timeouts if we do (even though the drive claims to support both
HIPM and DIPM).
Fixes: 7627a0edef54 ("ata: ahci: Drop low power policy board type") Cc: stable@vger.kernel.org Reported-by: Doru Iorgulescu <doru.iorgulescu1@gmail.com> Closes: https://bugzilla.kernel.org/show_bug.cgi?id=218832 Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com> Reviewed-by: Damien Le Moal <dlemoal@kernel.org> Signed-off-by: Niklas Cassel <cassel@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 7627a0edef54 ("ata: ahci: Drop low power policy board type")
dropped the board_ahci_low_power board type, and instead enables LPM if:
-The AHCI controller reports that it supports LPM (Partial/Slumber), and
-CONFIG_SATA_MOBILE_LPM_POLICY != 0, and
-The port is not defined as external in the per port PxCMD register, and
-The port is not defined as hotplug capable in the per port PxCMD
register.
Partial and Slumber LPM states can either be initiated by HIPM or DIPM.
For HIPM (host initiated power management) to get enabled, both the AHCI
controller and the drive have to report that they support HIPM.
For DIPM (device initiated power management) to get enabled, only the
drive has to report that it supports DIPM. However, the HBA will reject
device requests to enter LPM states which the HBA does not support.
The problem is that Crucial CT240BX500SSD1 drives do not handle low power
modes correctly. The problem was most likely not seen before because no
one had used this drive with a AHCI controller with LPM enabled.
Add a quirk so that we do not enable LPM for this drive, since we see
command timeouts if we do (even though the drive claims to support DIPM).
Fixes: 7627a0edef54 ("ata: ahci: Drop low power policy board type") Cc: stable@vger.kernel.org Reported-by: Aarrayy <lp610mh@gmail.com> Closes: https://bugzilla.kernel.org/show_bug.cgi?id=218832 Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com> Reviewed-by: Damien Le Moal <dlemoal@kernel.org> Signed-off-by: Niklas Cassel <cassel@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 7627a0edef54 ("ata: ahci: Drop low power policy board type")
dropped the board_ahci_low_power board type, and instead enables LPM if:
-The AHCI controller reports that it supports LPM (Partial/Slumber), and
-CONFIG_SATA_MOBILE_LPM_POLICY != 0, and
-The port is not defined as external in the per port PxCMD register, and
-The port is not defined as hotplug capable in the per port PxCMD
register.
Partial and Slumber LPM states can either be initiated by HIPM or DIPM.
For HIPM (host initiated power management) to get enabled, both the AHCI
controller and the drive have to report that they support HIPM.
For DIPM (device initiated power management) to get enabled, only the
drive has to report that it supports DIPM. However, the HBA will reject
device requests to enter LPM states which the HBA does not support.
The problem is that Apacer AS340 drives do not handle low power modes
correctly. The problem was most likely not seen before because no one
had used this drive with a AHCI controller with LPM enabled.
Add a quirk so that we do not enable LPM for this drive, since we see
command timeouts if we do (even though the drive claims to support DIPM).
Fixes: 7627a0edef54 ("ata: ahci: Drop low power policy board type") Cc: stable@vger.kernel.org Reported-by: Tim Teichmann <teichmanntim@outlook.de> Closes: https://lore.kernel.org/linux-ide/87bk4pbve8.ffs@tglx/ Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com> Reviewed-by: Damien Le Moal <dlemoal@kernel.org> Signed-off-by: Niklas Cassel <cassel@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit b8b8b4e0c052 ("ata: ahci: Add Intel Alder Lake-P AHCI controller
to low power chipsets list") added Intel Alder Lake to the ahci_pci_tbl.
Because of the way that the Intel PCS quirk was implemented, having
an explicit entry in the ahci_pci_tbl caused the Intel PCS quirk to
be applied. (The quirk was not being applied if there was no explict
entry.)
Thus, entries that were added to the ahci_pci_tbl also got the Intel
PCS quirk applied.
The quirk was cleaned up in commit 7edbb6059274 ("ahci: clean up
intel_pcs_quirk"), such that it is clear which entries that actually
applies the Intel PCS quirk.
Newer Intel AHCI controllers do not need the Intel PCS quirk,
and applying it when not needed actually breaks some platforms.
Do not apply the Intel PCS quirk for Intel Alder Lake.
This is in line with how things worked before commit b8b8b4e0c052 ("ata:
ahci: Add Intel Alder Lake-P AHCI controller to low power chipsets list"),
such that certain platforms using Intel Alder Lake will work once again.
When changing the maximum number of open zones, print that number
instead of the total number of zones.
Fixes: dc4d137ee3b7 ("null_blk: add support for max open/active zone limit for zoned devices") Cc: stable@vger.kernel.org Signed-off-by: Damien Le Moal <dlemoal@kernel.org> Reviewed-by: Niklas Cassel <cassel@kernel.org> Link: https://lore.kernel.org/r/20240528062852.437599-1-dlemoal@kernel.org Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Build environments might be running with different umask settings
resulting in indeterministic file modes for the files contained in
kheaders.tar.xz. The file itself is served with 444, i.e. world
readable. Archive the files explicitly with 744,a+X to improve
reproducibility across build environments.
--mode=0444 is not suitable as directories need to be executable. Also,
444 makes it hard to delete all the readonly files after extraction.
The kprobe_eventname.tc test checks if a function with .isra. can have a
kprobe attached to it. It loops through the kallsyms file for all the
functions that have the .isra. name, and checks if it exists in the
available_filter_functions file, and if it does, it uses it to attach a
kprobe to it.
The issue is that kprobes can not attach to functions that are listed more
than once in available_filter_functions. With the latest kernel, the
function that is found is: rapl_event_update.isra.0
It is listed twice. This causes the attached kprobe to it to fail which in
turn fails the test. Instead of just picking the function function that is
found in available_filter_functions, pick the first one that is listed
only once in available_filter_functions.
Cc: stable@vger.kernel.org Fixes: 604e3548236d ("selftests/ftrace: Select an existing function in kprobe_eventname test") Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org> Acked-by: Masami Hiramatsu (Google) <mhiramat@kernel.org> Signed-off-by: Shuah Khan <skhan@linuxfoundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On riscv32, it is possible for the last page in virtual address space
(0xfffff000) to be allocated. This page overlaps with PTR_ERR, so that
shouldn't happen.
There is already some code to ensure memblock won't allocate the last page.
However, buddy allocator is left unchecked.
Fix this by reserving physical memory that would be mapped at virtual
addresses greater than 0xfffff000.
Reported-by: Björn Töpel <bjorn@kernel.org> Closes: https://lore.kernel.org/linux-riscv/878r1ibpdn.fsf@all.your.base.are.belong.to.us Fixes: 76d2a0493a17 ("RISC-V: Init and Halt Code") Signed-off-by: Nam Cao <namcao@linutronix.de> Cc: <stable@vger.kernel.org> Tested-by: Björn Töpel <bjorn@rivosinc.com> Reviewed-by: Björn Töpel <bjorn@rivosinc.com> Reviewed-by: Mike Rapoport (IBM) <rppt@kernel.org> Link: https://lore.kernel.org/r/20240425115201.3044202-1-namcao@linutronix.de Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For ${atomic}_sub_and_test() the @i parameter is the value to subtract,
not add. Fix the typo in the kerneldoc template and generate the headers
with this update.
Fixes: ad8110706f38 ("locking/atomic: scripts: generate kerneldoc comments") Suggested-by: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Carlos Llamas <cmllamas@google.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Acked-by: Mark Rutland <mark.rutland@arm.com> Reviewed-by: Kees Cook <keescook@chromium.org> Cc: stable@vger.kernel.org Link: https://lkml.kernel.org/r/20240515133844.3502360-1-cmllamas@google.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 0a44dfc07074 ("wifi: mac80211: simplify non-chanctx
drivers") ieee80211_hw_config() is no longer called with changed = ~0.
rtlwifi relied on ~0 in order to ignore the default retry limits of
4/7, preferring 48/48 in station mode and 7/7 in AP/IBSS.
RTL8192DU has a lot of packet loss with the default limits from
mac80211. Fix it by ignoring IEEE80211_CONF_CHANGE_RETRY_LIMITS
completely, because it's the simplest solution.
If the --itrace option is used more than once, the options are
combined, but "i" and "y" (sub-)options can be corrupted because
itrace_do_parse_synth_opts() incorrectly overwrites the period type and
period with default values.
For example, with:
--itrace=i0ns --itrace=e
The processing of "--itrace=e", resets the "i" period from 0 nanoseconds
to the default 100 microseconds.
Fix by performing the default setting of period type and period only if
"i" or "y" are present in the currently processed --itrace value.
Fixes: f6986c95af84ff2a ("perf session: Add instruction tracing options") Signed-off-by: Adrian Hunter <adrian.hunter@intel.com> Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Andi Kleen <ak@linux.intel.com> Cc: Ian Rogers <irogers@google.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Namhyung Kim <namhyung@kernel.org> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20240315071334.3478-2-adrian.hunter@intel.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The task was waiting for the refcount become to 1, but from the vmcore,
we found the refcount has already been 1. It seems that the task didn't
get woken up by perf_event_release_kernel() and got stuck forever. The
below scenario may cause the problem.
In this case, all events of the ctx have been freed, so we couldn't
find the ctx in free_list and Thread A will miss the wakeup. It's thus
necessary to add a wakeup after dropping the reference.
Fixes: 1cf8dfe8a661 ("perf/core: Fix race between close() and fork()") Signed-off-by: Haifeng Xu <haifeng.xu@shopee.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Reviewed-by: Frederic Weisbecker <frederic@kernel.org> Acked-by: Mark Rutland <mark.rutland@arm.com> Cc: stable@vger.kernel.org Link: https://lkml.kernel.org/r/20240513103948.33570-1-haifeng.xu@shopee.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
AMD Zen-based systems use a System Management Network (SMN) that
provides access to implementation-specific registers.
SMN accesses are done indirectly through an index/data pair in PCI
config space. The PCI config access may fail and return an error code.
This would prevent the "read" value from being updated.
However, the PCI config access may succeed, but the return value may be
invalid. This is in similar fashion to PCI bad reads, i.e. return all
bits set.
Most systems will return 0 for SMN addresses that are not accessible.
This is in line with AMD convention that unavailable registers are
Read-as-Zero/Writes-Ignored.
However, some systems will return a "PCI Error Response" instead. This
value, along with an error code of 0 from the PCI config access, will
confuse callers of the amd_smn_read() function.
Check for this condition, clear the return value, and set a proper error
code.
Fixes: ddfe43cdc0da ("x86/amd_nb: Add SMN and Indirect Data Fabric access for AMD Fam17h") Signed-off-by: Yazen Ghannam <yazen.ghannam@amd.com> Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20230403164244.471141-1-yazen.ghannam@amd.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The call to cc_platform_has() triggers a fault and system crash if call depth
tracking is active because the GS segment has been reset by load_segments() and
GS_BASE is now 0 but call depth tracking uses per-CPU variables to operate.
Call cc_platform_has() earlier in the function when GS is still valid.
its_vlpi_prop_update() calls lpi_write_config() which obtains the
mapping information for a VLPI without lock held. So it could race
with its_vlpi_unmap().
Since all calls from its_irq_set_vcpu_affinity() require the same
lock to be held, hoist the locking there instead of sprinkling the
locking all over the place.
This bug was discovered using Coverity Static Analysis Security Testing
(SAST) by Synopsys, Inc.
Now that the PLIC uses a platform driver, the driver is probed later in the
boot process, where interrupts from peripherals might already be pending.
As a result, plic_handle_irq() may be called as early as the call to
irq_set_chained_handler() completes. But this call happens before the
per-context handler is completely set up, so there is a window where
plic_handle_irq() can see incomplete per-context state and crash.
Avoid this by delaying the call to irq_set_chained_handler() until all
handlers from all PLICs are initialized.
Fixes: 8ec99b033147 ("irqchip/sifive-plic: Convert PLIC driver into a platform driver") Reported-by: Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by: Samuel Holland <samuel.holland@sifive.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Tested-by: Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by: Anup Patel <anup@brainfault.org> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20240529215458.937817-1-samuel.holland@sifive.com Closes: https://lore.kernel.org/r/CAMuHMdVYFFR7K5SbHBLY-JHhb7YpgGMS_hnRWm8H0KD-wBo+4A@mail.gmail.com/ Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The creation of new subflows can fail for different reasons. If no
subflow have been created using the received ADD_ADDR, the related
counters should not be updated, otherwise they will never be decremented
for events related to this ID later on.
For the moment, the number of accepted ADD_ADDR is only decremented upon
the reception of a related RM_ADDR, and only if the remote address ID is
currently being used by at least one subflow. In other words, if no
subflow can be created with the received address, the counter will not
be decremented. In this case, it is then important not to increment
pm.add_addr_accepted counter, and not to modify pm.accept_addr bit.
Note that this patch does not modify the behaviour in case of failures
later on, e.g. if the MP Join is dropped or rejected.
The "remove invalid addresses" MP Join subtest has been modified to
validate this case. The broadcast IP address is added before the "valid"
address that will be used to successfully create a subflow, and the
limit is decreased by one: without this patch, it was not possible to
create the last subflow, because:
- the broadcast address would have been accepted even if it was not
usable: the creation of a subflow to this address results in an error,
- the limit of 2 accepted ADD_ADDR would have then been reached.
The RmAddr MIB counter is supposed to be incremented once when a valid
RM_ADDR has been received. Before this patch, it could have been
incremented as many times as the number of subflows connected to the
linked address ID, so it could have been 0, 1 or more than 1.
The "RmSubflow" is incremented after a local operation. In this case,
it is normal to tied it with the number of subflows that have been
actually removed.
The "remove invalid addresses" MP Join subtest has been modified to
validate this case. A broadcast IP address is now used instead: the
client will not be able to create a subflow to this address. The
consequence is that when receiving the RM_ADDR with the ID attached to
this broadcast IP address, no subflow linked to this ID will be found.
This is strictly related to commit fb7a0d334894 ("mptcp: ensure snd_nxt
is properly initialized on connect"). It turns out that syzkaller can
trigger the retransmit after fallback and before processing any other
incoming packet - so that snd_una is still left uninitialized.
Address the issue explicitly initializing snd_una together with snd_nxt
and write_seq.
Suggested-by: Mat Martineau <martineau@kernel.org> Fixes: 8fd738049ac3 ("mptcp: fallback in case of simultaneous connect") Cc: stable@vger.kernel.org Reported-by: Christoph Paasch <cpaasch@apple.com> Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/485 Signed-off-by: Paolo Abeni <pabeni@redhat.com> Reviewed-by: Mat Martineau <martineau@kernel.org> Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org> Link: https://lore.kernel.org/r/20240607-upstream-net-20240607-misc-fixes-v1-1-1ab9ddfa3d00@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When reading EDID fails and driver reports no modes available, the DRM
core adds an artificial 1024x786 mode to the connector. Unfortunately
some variants of the Exynos HDMI (like the one in Exynos4 SoCs) are not
able to drive such mode, so report a safe 640x480 mode instead of nothing
in case of the EDID reading failure.
This fixes the following issue observed on Trats2 board since commit 13d5b040363c ("drm/exynos: do not return negative values from .get_modes()"):
[drm] Exynos DRM: using 11c00000.fimd device for DMA mapping operations
exynos-drm exynos-drm: bound 11c00000.fimd (ops fimd_component_ops)
exynos-drm exynos-drm: bound 12c10000.mixer (ops mixer_component_ops)
exynos-dsi 11c80000.dsi: [drm:samsung_dsim_host_attach] Attached s6e8aa0 device (lanes:4 bpp:24 mode-flags:0x10b)
exynos-drm exynos-drm: bound 11c80000.dsi (ops exynos_dsi_component_ops)
exynos-drm exynos-drm: bound 12d00000.hdmi (ops hdmi_component_ops)
[drm] Initialized exynos 1.1.0 20180330 for exynos-drm on minor 1
exynos-hdmi 12d00000.hdmi: [drm:hdmiphy_enable.part.0] *ERROR* PLL could not reach steady state
panel-samsung-s6e8aa0 11c80000.dsi.0: ID: 0xa2, 0x20, 0x8c
exynos-mixer 12c10000.mixer: timeout waiting for VSYNC
------------[ cut here ]------------
WARNING: CPU: 1 PID: 11 at drivers/gpu/drm/drm_atomic_helper.c:1682 drm_atomic_helper_wait_for_vblanks.part.0+0x2b0/0x2b8
[CRTC:70:crtc-1] vblank wait timed out
Modules linked in:
CPU: 1 PID: 11 Comm: kworker/u16:0 Not tainted 6.9.0-rc5-next-20240424 #14913
Hardware name: Samsung Exynos (Flattened Device Tree)
Workqueue: events_unbound deferred_probe_work_func
Call trace:
unwind_backtrace from show_stack+0x10/0x14
show_stack from dump_stack_lvl+0x68/0x88
dump_stack_lvl from __warn+0x7c/0x1c4
__warn from warn_slowpath_fmt+0x11c/0x1a8
warn_slowpath_fmt from drm_atomic_helper_wait_for_vblanks.part.0+0x2b0/0x2b8
drm_atomic_helper_wait_for_vblanks.part.0 from drm_atomic_helper_commit_tail_rpm+0x7c/0x8c
drm_atomic_helper_commit_tail_rpm from commit_tail+0x9c/0x184
commit_tail from drm_atomic_helper_commit+0x168/0x190
drm_atomic_helper_commit from drm_atomic_commit+0xb4/0xe0
drm_atomic_commit from drm_client_modeset_commit_atomic+0x23c/0x27c
drm_client_modeset_commit_atomic from drm_client_modeset_commit_locked+0x60/0x1cc
drm_client_modeset_commit_locked from drm_client_modeset_commit+0x24/0x40
drm_client_modeset_commit from __drm_fb_helper_restore_fbdev_mode_unlocked+0x9c/0xc4
__drm_fb_helper_restore_fbdev_mode_unlocked from drm_fb_helper_set_par+0x2c/0x3c
drm_fb_helper_set_par from fbcon_init+0x3d8/0x550
fbcon_init from visual_init+0xc0/0x108
visual_init from do_bind_con_driver+0x1b8/0x3a4
do_bind_con_driver from do_take_over_console+0x140/0x1ec
do_take_over_console from do_fbcon_takeover+0x70/0xd0
do_fbcon_takeover from fbcon_fb_registered+0x19c/0x1ac
fbcon_fb_registered from register_framebuffer+0x190/0x21c
register_framebuffer from __drm_fb_helper_initial_config_and_unlock+0x350/0x574
__drm_fb_helper_initial_config_and_unlock from exynos_drm_fbdev_client_hotplug+0x6c/0xb0
exynos_drm_fbdev_client_hotplug from drm_client_register+0x58/0x94
drm_client_register from exynos_drm_bind+0x160/0x190
exynos_drm_bind from try_to_bring_up_aggregate_device+0x200/0x2d8
try_to_bring_up_aggregate_device from __component_add+0xb0/0x170
__component_add from mixer_probe+0x74/0xcc
mixer_probe from platform_probe+0x5c/0xb8
platform_probe from really_probe+0xe0/0x3d8
really_probe from __driver_probe_device+0x9c/0x1e4
__driver_probe_device from driver_probe_device+0x30/0xc0
driver_probe_device from __device_attach_driver+0xa8/0x120
__device_attach_driver from bus_for_each_drv+0x80/0xcc
bus_for_each_drv from __device_attach+0xac/0x1fc
__device_attach from bus_probe_device+0x8c/0x90
bus_probe_device from deferred_probe_work_func+0x98/0xe0
deferred_probe_work_func from process_one_work+0x240/0x6d0
process_one_work from worker_thread+0x1a0/0x3f4
worker_thread from kthread+0x104/0x138
kthread from ret_from_fork+0x14/0x28
Exception stack(0xf0895fb0 to 0xf0895ff8)
...
irq event stamp: 82357
hardirqs last enabled at (82363): [<c01a96e8>] vprintk_emit+0x308/0x33c
hardirqs last disabled at (82368): [<c01a969c>] vprintk_emit+0x2bc/0x33c
softirqs last enabled at (81614): [<c0101644>] __do_softirq+0x320/0x500
softirqs last disabled at (81609): [<c012dfe0>] __irq_exit_rcu+0x130/0x184
---[ end trace 0000000000000000 ]---
exynos-drm exynos-drm: [drm] *ERROR* flip_done timed out
exynos-drm exynos-drm: [drm] *ERROR* [CRTC:70:crtc-1] commit wait timed out
exynos-drm exynos-drm: [drm] *ERROR* flip_done timed out
exynos-drm exynos-drm: [drm] *ERROR* [CONNECTOR:74:HDMI-A-1] commit wait timed out
exynos-drm exynos-drm: [drm] *ERROR* flip_done timed out
exynos-drm exynos-drm: [drm] *ERROR* [PLANE:56:plane-5] commit wait timed out
exynos-mixer 12c10000.mixer: timeout waiting for VSYNC
Cc: stable@vger.kernel.org Fixes: 13d5b040363c ("drm/exynos: do not return negative values from .get_modes()") Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Inki Dae <inki.dae@samsung.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
the commit referenced below leads to this NUMA configuration no longer
being refused by a CONFIG_NUMA=y kernel (previously
NUMA: nodes only cover 6144MB of your 8185MB e820 RAM. Not used.
No NUMA configuration found
Faking a node at [mem 0x0000000000000000-0x000000027fffffff]
was seen in the log directly after the message quoted above), because of
memblock_validate_numa_coverage() checking for NUMA_NO_NODE (only). This
in turn led to memblock_alloc_range_nid()'s warning about MAX_NUMNODES
triggering, followed by a NULL deref in memmap_init() when trying to
access node 64's (NODE_SHIFT=6) node data.
To compensate said change, make memblock_set_node() warn on and adjust
a passed in value of MAX_NUMNODES, just like various other functions
already do.
Fixes: ff6c3d81f2e8 ("NUMA: optimize detection of memory with no node id assigned by firmware") Signed-off-by: Jan Beulich <jbeulich@suse.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/1c8a058c-5365-4f27-a9f1-3aeb7fb3e7b2@suse.com Signed-off-by: Mike Rapoport (IBM) <rppt@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is reported that commit 950210887670 ("thermal: core: Drop
trips_disabled bitmask") causes the maximum frequency of CPUs to drop
further down with every system sleep-wake cycle on Intel Core i7-4710HQ.
This turns out to be due to a trip point whose temperature is equal to 0
degrees Celsius which is acted on every time the system wakes from sleep.
Before commit 950210887670 this trip point would be disabled wia the
trips_disabled bitmask, but now it is treated as a valid one.
Since ACPI thermal control is generally about protection against
overheating, trip points with temperature of 0 centigrade or below are
not particularly useful there, so initialize them all as invalid which
fixes the problem at hand.
Fixes: 950210887670 ("thermal: core: Drop trips_disabled bitmask") Closes: https://lore.kernel.org/linux-pm/3f71747b-f852-4ee0-b384-cf46b2aefa3f@gmx.com Reported-by: Tibor Billes <tbilles@gmx.com> Tested-by: Tibor Billes <tbilles@gmx.com> Cc: 6.7+ <stable@vger.kernel.org> # 6.7+ Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A Rembrandt-based HP thin client is reported to have problems where
the NVME disk isn't present after resume from s2idle.
This is because the NVME disk wasn't put into D3 at suspend, and
that happened because the StorageD3Enable _DSD was missing in the BIOS.
As AMD's architecture requires that the NVME is in D3 for s2idle, adjust
the criteria for force_storage_d3 to match *all* Zen SoCs when the FADT
advertises low power idle support.
This will ensure that any future products with this BIOS deficiency don't
need to be added to the allow list of overrides.
Cc: All applicable <stable@vger.kernel.org> Signed-off-by: Mario Limonciello <mario.limonciello@amd.com> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
PA-RISC systems with PA8800 and PA8900 processors have had problems
with random segmentation faults for many years. Systems with earlier
processors are much more stable.
Systems with PA8800 and PA8900 processors have a large L2 cache which
needs per page flushing for decent performance when a large range is
flushed. The combined cache in these systems is also more sensitive to
non-equivalent aliases than the caches in earlier systems.
The majority of random segmentation faults that I have looked at
appear to be memory corruption in memory allocated using mmap and
malloc.
My first attempt at fixing the random faults didn't work. On
reviewing the cache code, I realized that there were two issues
which the existing code didn't handle correctly. Both relate
to cache move-in. Another issue is that the present bit in PTEs
is racy.
1) PA-RISC caches have a mind of their own and they can speculatively
load data and instructions for a page as long as there is a entry in
the TLB for the page which allows move-in. TLBs are local to each
CPU. Thus, the TLB entry for a page must be purged before flushing
the page. This is particularly important on SMP systems.
In some of the flush routines, the flush routine would be called
and then the TLB entry would be purged. This was because the flush
routine needed the TLB entry to do the flush.
2) My initial approach to trying the fix the random faults was to
try and use flush_cache_page_if_present for all flush operations.
This actually made things worse and led to a couple of hardware
lockups. It finally dawned on me that some lines weren't being
flushed because the pte check code was racy. This resulted in
random inequivalent mappings to physical pages.
The __flush_cache_page tmpalias flush sets up its own TLB entry
and it doesn't need the existing TLB entry. As long as we can find
the pte pointer for the vm page, we can get the pfn and physical
address of the page. We can also purge the TLB entry for the page
before doing the flush. Further, __flush_cache_page uses a special
TLB entry that inhibits cache move-in.
When switching page mappings, we need to ensure that lines are
removed from the cache. It is not sufficient to just flush the
lines to memory as they may come back.
This made it clear that we needed to implement all the required
flush operations using tmpalias routines. This includes flushes
for user and kernel pages.
After modifying the code to use tmpalias flushes, it became clear
that the random segmentation faults were not fully resolved. The
frequency of faults was worse on systems with a 64 MB L2 (PA8900)
and systems with more CPUs (rp4440).
The warning that I added to flush_cache_page_if_present to detect
pages that couldn't be flushed triggered frequently on some systems.
Helge and I looked at the pages that couldn't be flushed and found
that the PTE was either cleared or for a swap page. Ignoring pages
that were swapped out seemed okay but pages with cleared PTEs seemed
problematic.
I looked at routines related to pte_clear and noticed ptep_clear_flush.
The default implementation just flushes the TLB entry. However, it was
obvious that on parisc we need to flush the cache page as well. If
we don't flush the cache page, stale lines will be left in the cache
and cause random corruption. Once a PTE is cleared, there is no way
to find the physical address associated with the PTE and flush the
associated page at a later time.
I implemented an updated change with a parisc specific version of
ptep_clear_flush. It fixed the random data corruption on Helge's rp4440
and rp3440, as well as on my c8000.
At this point, I realized that I could restore the code where we only
flush in flush_cache_page_if_present if the page has been accessed.
However, for this, we also need to flush the cache when the accessed
bit is cleared in ptep_clear_flush_young to keep things synchronized.
The default implementation only flushes the TLB entry.
Other changes in this version are:
1) Implement parisc specific version of ptep_get. It's identical to
default but needed in arch/parisc/include/asm/pgtable.h.
2) Revise parisc implementation of ptep_test_and_clear_young to use
ptep_get (READ_ONCE).
3) Drop parisc implementation of ptep_get_and_clear. We can use default.
4) Revise flush_kernel_vmap_range and invalidate_kernel_vmap_range to
use full data cache flush.
5) Move flush_cache_vmap and flush_cache_vunmap to cache.c. Handle
VM_IOREMAP case in flush_cache_vmap.
At this time, I don't know whether it is better to always flush when
the PTE present bit is set or when both the accessed and present bits
are set. The later saves flushing pages that haven't been accessed,
but we need to flush in ptep_clear_flush_young. It also needs a page
table lookup to find the PTE pointer. The lpa instruction only needs
a page table lookup when the PTE entry isn't in the TLB.
We don't atomically handle setting and clearing the _PAGE_ACCESSED bit.
If we miss an update, we may miss a flush and the cache may get corrupted.
Whether the current code is effectively atomic depends on process control.
When CONFIG_FLUSH_PAGE_ACCESSED is set to zero, the page will eventually
be flushed when the PTE is cleared or in flush_cache_page_if_present. The
_PAGE_ACCESSED bit is not used, so the problem is avoided.
The flush method can be selected using the CONFIG_FLUSH_PAGE_ACCESSED
define in cache.c. The default is 0. I didn't see a large difference
in performance.
Signed-off-by: John David Anglin <dave.anglin@bell.net> Cc: <stable@vger.kernel.org> # v6.6+ Signed-off-by: Helge Deller <deller@gmx.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Synchronize the dev->driver usage in really_probe() and dev_uevent().
These can run in different threads, what can result in the following
race condition for dev->driver uninitialization:
dev_uevent() {
...
if (dev->driver)
// If dev->driver is NULLed from really_probe() from here on,
// after above check, the system crashes
add_uevent_var(env, "DRIVER=%s", dev->driver->name);
...
}
really_probe() holds the lock, already. So nothing needs to be done
there. dev_uevent() is called with lock held, often, too. But not
always. What implies that we can't add any locking in dev_uevent()
itself. So fix this race by adding the lock to the non-protected
path. This is the path where above race is observed:
But these are regarding the *initialization* of dev->driver
dev->driver = drv;
As this switches dev->driver to non-NULL these reports can be considered
to be false-positives (which should be "fixed" by this commit, as well,
though).
The same issue was reported and tried to be fixed back in 2015 in
When devm_regmap_init_i2c() fails, regmap_ee could be error pointer,
instead of checking for IS_ERR(regmap_ee), regmap is checked which looks
like a copy paste error.
Fixes: a1d1ba5e1c28 ("iio: temperature: mlx90635 MLX90635 IR Temperature sensor") Reviewed-by: Crt Mori<cmo@melexis.com> Signed-off-by: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com> Link: https://lore.kernel.org/r/20240513203427.3208696-1-harshit.m.mogalapalli@oracle.com Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ODR switching happens in 2 steps, update to store the new value and then
apply when the ODR change flag is received in the data. When switching to
the same ODR value, the ODR change flag is never happening, and frequency
switching is blocked waiting for the never coming apply.
Fix the issue by preventing update to happen when switching to same ODR
value.
In case of error in the bmi323_trigger_handler() function, the
function exits without calling the iio_trigger_notify_done()
which is responsible for informing the attached trigger that
the process is done and in case there is a .reenable(), to
call it.
However, we return IIO_VAL_INT_PLUS_MICRO (should have been NANO) as
the scale type. So when converting the raw temperature value to the
'processed' temperature value we will get (assuming raw=810,
offset=-753):
da05b143a308 ("x86/boot: Don't add the EFI stub to targets")
after the tagged patch incorrectly reverted it.
vmlinux-objs-y is added to targets, with an assumption that they are all
relative to $(obj); adding a $(objtree)/drivers/... path causes the
build to incorrectly create a useless
arch/x86/boot/compressed/drivers/... directory tree.
Fix this just by using a different make variable for the EFI stub.
Commit 66601a29bb23 ("leds: class: If no default trigger is given, make
hw_control trigger the default trigger") causes ledtrig-netdev to get
set as default trigger on various network LEDs.
This causes users to hit a pre-existing AB-BA deadlock issue in
ledtrig-netdev between the LED-trigger locks and the rtnl mutex,
resulting in hung tasks in kernels >= 6.9.
Solving the deadlock is non trivial, so for now revert the change to
set the hw_control trigger as default trigger, so that ledtrig-netdev
no longer gets activated automatically for various network LEDs.
The netdev trigger is not needed because the network LEDs are usually under
hw-control and the netdev trigger tries to leave things that way so setting
it as the active trigger for the LED class device is a no-op.
Fixes: 66601a29bb23 ("leds: class: If no default trigger is given, make hw_control trigger the default trigger") Reported-by: Genes Lists <lists@sapience.com> Closes: https://lore.kernel.org/all/9d189ec329cfe68ed68699f314e191a10d4b5eda.camel@sapience.com/ Reported-by: Johannes Wüller <johanneswueller@gmail.com> Closes: https://lore.kernel.org/lkml/e441605c-eaf2-4c2d-872b-d8e541f4cf60@gmail.com/ Cc: stable@vger.kernel.org Signed-off-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Acked-by: Lee Jones <lee@kernel.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After the recent commit 5097cbcb38e6 ("sched/isolation: Prevent boot crash
when the boot CPU is nohz_full") the kernel no longer crashes, but there is
another problem.
In this case tick_setup_device() calls tick_take_do_timer_from_boot() to
update tick_do_timer_cpu and this triggers the WARN_ON_ONCE(irqs_disabled)
in smp_call_function_single().
Kill tick_take_do_timer_from_boot() and just use WRITE_ONCE(), the new
comment explains why this is safe (thanks Thomas!).
If the directory name in the root of the share starts with
character like 镜(0x955c) or Ṝ(0x1e5c), it (and anything inside)
cannot be accessed. The leading slash check must be checked after
converting unicode to nls string.
Cc: stable@vger.kernel.org Signed-off-by: Namjae Jeon <linkinjeon@kernel.org> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When auxiliary_device_add() returns error and then calls
auxiliary_device_uninit(), callback function
gp_auxiliary_device_release() calls ida_free() and
kfree(aux_device_wrapper) to free memory. We should't
call them again in the error handling path.
Fix this by skipping the redundant cleanup functions.
Fixes: 393fc2f5948f ("misc: microchip: pci1xxxx: load auxiliary bus driver for the PIO function in the multi-function endpoint of pci1xxxx device.") Signed-off-by: Yongzhi Liu <hyperlyzcs@gmail.com> Link: https://lore.kernel.org/r/20240523121434.21855-3-hyperlyzcs@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case of token is released due to token->state == BNXT_HWRM_DEFERRED,
released token (set to NULL) is used in log messages. This issue is
expected to be prevented by HWRM_ERR_CODE_PF_UNAVAILABLE error code. But
this error code is returned by recent firmware. So some firmware may not
return it. This may lead to NULL pointer dereference.
Adjust this issue by adding token pointer check.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 8fa4219dba8e ("bnxt_en: add dynamic debug support for HWRM messages") Suggested-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: Aleksandr Mishin <amishin@t-argos.ru> Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com> Reviewed-by: Michael Chan <michael.chan@broadcom.com> Link: https://lore.kernel.org/r/20240611082547.12178-1-amishin@t-argos.ru Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Read with MSG_PEEK flag loops if the first byte to read is an OOB byte.
commit 22dd70eb2c3d ("af_unix: Don't peek OOB data without MSG_OOB.")
addresses the loop issue but does not address the issue that no data
beyond OOB byte can be read.
Firmware interface 1.10.2.118 has increased the size of
HWRM_PORT_PHY_QCFG response beyond the maximum size that can be
forwarded. When the VF's link state is not the default auto state,
the PF will need to forward the response back to the VF to indicate
the forced state. This regression may cause the VF to fail to
initialize.
Fix it by capping the HWRM_PORT_PHY_QCFG response to the maximum
96 bytes. The SPEEDS2_SUPPORTED flag needs to be cleared because the
new speeds2 fields are beyond the legacy structure. Also modify
bnxt_hwrm_fwd_resp() to print a warning if the message size exceeds 96
bytes to make this failure more obvious.
Fixes: 84a911db8305 ("bnxt_en: Update firmware interface to 1.10.2.118") Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com> Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Link: https://lore.kernel.org/r/20240612231736.57823-1-michael.chan@broadcom.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When queues are started, netif_napi_add() and napi_enable() are called.
If there are 4 queues and only 3 queues are used for the current
configuration, only 3 queues' napi should be registered and enabled.
The ionic_qcq_enable() checks whether the .poll pointer is not NULL for
enabling only the using queue' napi. Unused queues' napi will not be
registered by netif_napi_add(), so the .poll pointer indicates NULL.
But it couldn't distinguish whether the napi was unregistered or not
because netif_napi_del() doesn't reset the .poll pointer to NULL.
So, ionic_qcq_enable() calls napi_enable() for the queue, which was
unregistered by netif_napi_del().
Tests show that user fence signalling requires kind of write barrier,
otherwise not all writes performed by the workload will be available
to userspace. It is already done for render and compute, we need it
also for the rest: video, gsc, copy.
I converted br_mst_set_state to RCU to avoid a vlan use-after-free
but forgot to change the vlan group dereference helper. Switch to vlan
group RCU deref helper to fix the suspicious rcu usage warning.
Pass the already obtained vlan group pointer to br_mst_vlan_set_state()
instead of dereferencing it again. Each caller has already correctly
dereferenced it for their context. This change is required for the
following suspicious RCU dereference fix. No functional changes
intended.
The net.ipv6.route.flush system parameter takes a value which specifies
a delay used during the flush operation for aging exception routes. The
written value is however not used in the currently requested flush and
instead utilized only in the next one.
A problem is that ipv6_sysctl_rtcache_flush() first reads the old value
of net->ipv6.sysctl.flush_delay into a local delay variable and then
calls proc_dointvec() which actually updates the sysctl based on the
provided input.
Fix the problem by switching the order of the two operations.
Fixes: 4990509f19e8 ("[NETNS][IPV6]: Make sysctls route per namespace.") Signed-off-by: Petr Pavlu <petr.pavlu@suse.com> Reviewed-by: David Ahern <dsahern@kernel.org> Link: https://lore.kernel.org/r/20240607112828.30285-1-petr.pavlu@suse.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Friedrich Weber reported a kernel crash problem and bisected to commit 81ada09cc25e ("blk-flush: reuse rq queuelist in flush state machine").
The root cause is that we use "list_move_tail(&rq->queuelist, pending)"
in the PREFLUSH/POSTFLUSH sequences. But rq->queuelist.next == xxx since
it's popped out from plug->cached_rq in __blk_mq_alloc_requests_batch().
We don't initialize its queuelist just for this first request, although
the queuelist of all later popped requests will be initialized.
Fix it by changing to use "list_add_tail(&rq->queuelist, pending)" so
rq->queuelist doesn't need to be initialized. It should be ok since rq
can't be on any list when PREFLUSH or POSTFLUSH, has no move actually.
Please note the commit 81ada09cc25e ("blk-flush: reuse rq queuelist in
flush state machine") also has another requirement that no drivers would
touch rq->queuelist after blk_mq_end_request() since we will reuse it to
add rq to the post-flush pending list in POSTFLUSH. If this is not true,
we will have to revert that commit IMHO.
This updated version adds "list_del_init(&rq->queuelist)" in flush rq
callback since the dm layer may submit request of a weird invalid format
(REQ_FSEQ_PREFLUSH | REQ_FSEQ_POSTFLUSH), which causes double list_add
if without this "list_del_init(&rq->queuelist)". The weird invalid format
problem should be fixed in dm layer.
Reported-by: Friedrich Weber <f.weber@proxmox.com> Closes: https://lore.kernel.org/lkml/14b89dfb-505c-49f7-aebb-01c54451db40@proxmox.com/ Closes: https://lore.kernel.org/lkml/c9d03ff7-27c5-4ebd-b3f6-5a90d96f35ba@proxmox.com/ Fixes: 81ada09cc25e ("blk-flush: reuse rq queuelist in flush state machine") Cc: Christoph Hellwig <hch@lst.de> Cc: ming.lei@redhat.com Cc: bvanassche@acm.org Tested-by: Friedrich Weber <f.weber@proxmox.com> Signed-off-by: Chengming Zhou <chengming.zhou@linux.dev> Reviewed-by: Christoph Hellwig <hch@lst.de> Link: https://lore.kernel.org/r/20240608143115.972486-1-chengming.zhou@linux.dev Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
The current cbs parameter depends on speed after uplinking,
which is not needed and will report a configuration error
if the port is not initially connected. The UAPI exposed by
tc-cbs requires userspace to recalculate the send slope anyway,
because the formula depends on port_transmit_rate (see man tc-cbs),
which is not an invariant from tc's perspective. Therefore, we
use offload->sendslope and offload->idleslope to derive the
original port_transmit_rate from the CBS formula.
Fixes: 1f705bc61aee ("net: stmmac: Add support for CBS QDISC") Signed-off-by: Xiaolei Wang <xiaolei.wang@windriver.com> Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com> Reviewed-by: Vladimir Oltean <olteanv@gmail.com> Link: https://lore.kernel.org/r/20240608143524.2065736-1-xiaolei.wang@windriver.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
TSO currently fails when the skb's gso_type field has more than one bit
set.
TSO packets can be passed from userspace using PF_PACKET, TUNTAP and a
few others, using virtio_net_hdr (e.g., PACKET_VNET_HDR). This includes
virtualization, such as QEMU, a real use-case.
The gso_type and gso_size fields as passed from userspace in
virtio_net_hdr are not trusted blindly by the kernel. It adds gso_type
|= SKB_GSO_DODGY to force the packet to enter the software GSO stack
for verification.
This issue might similarly come up when the CWR bit is set in the TCP
header for congestion control, causing the SKB_GSO_TCP_ECN gso_type bit
to be set.
Fixes: a57e5de476be ("gve: DQO: Add TX path") Signed-off-by: Joshua Washington <joshwash@google.com> Reviewed-by: Praveen Kaligineedi <pkaligineedi@google.com> Reviewed-by: Harshitha Ramamurthy <hramamurthy@google.com> Reviewed-by: Willem de Bruijn <willemb@google.com> Suggested-by: Eric Dumazet <edumazet@google.com> Acked-by: Andrei Vagin <avagin@gmail.com>
v2 - Remove unnecessary comments, remove line break between fixes tag
and signoffs.
In ufshcd_clock_scaling_prepare(), after SCSI layer is blocked,
ufshcd_pending_cmds() is called to check whether there are pending
transactions or not. And only if there are no pending transactions can we
proceed to kickstart the clock scaling sequence.
ufshcd_pending_cmds() traverses over all SCSI devices and calls
sbitmap_weight() on their budget_map. sbitmap_weight() can be broken down
to three steps:
1. Calculate the nr outstanding bits set in the 'word' bitmap.
2. Calculate the nr outstanding bits set in the 'cleared' bitmap.
3. Subtract the result from step 1 by the result from step 2.
This can lead to a race condition as outlined below:
Assume there is one pending transaction in the request queue of one SCSI
device, say sda, and the budget token of this request is 0, the 'word' is
0x1 and the 'cleared' is 0x0.
1. When step 1 executes, it gets the result as 1.
2. Before step 2 executes, block layer tries to dispatch a new request to
sda. Since the SCSI layer is blocked, the request cannot pass through
SCSI but the block layer would do budget_get() and budget_put() to
sda's budget map regardless, so the 'word' has become 0x3 and 'cleared'
has become 0x2 (assume the new request got budget token 1).
3. When step 2 executes, it gets the result as 1.
4. When step 3 executes, it gets the result as 0, meaning there is no
pending transactions, which is wrong.
Thread A Thread B
ufshcd_pending_cmds() __blk_mq_sched_dispatch_requests()
| |
sbitmap_weight(word) |
| scsi_mq_get_budget()
| |
| scsi_mq_put_budget()
| |
sbitmap_weight(cleared)
...
When this race condition happens, the clock scaling sequence is started
with transactions still in flight, leading to subsequent hibernate enter
failure, broken link, task abort and back to back error recovery.
Fix this race condition by quiescing the request queues before calling
ufshcd_pending_cmds() so that block layer won't touch the budget map when
ufshcd_pending_cmds() is working on it. In addition, remove the SCSI layer
blocking/unblocking to reduce redundancies and latencies.
Fixes: 8d077ede48c1 ("scsi: ufs: Optimize the command queueing code") Co-developed-by: Can Guo <quic_cang@quicinc.com> Signed-off-by: Can Guo <quic_cang@quicinc.com> Signed-off-by: Ziqi Chen <quic_ziqichen@quicinc.com> Link: https://lore.kernel.org/r/1717754818-39863-1-git-send-email-quic_ziqichen@quicinc.com Reviewed-by: Bart Van Assche <bvanassche@acm.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When reworking the range checking for get_user(), the get_user_8() case
on 32-bit wasn't zeroing the high register. (The jump to bad_get_user_8
was accidentally dropped.) Restore the correct error handling
destination (and rename the jump to using the expected ".L" prefix).
While here, switch to using a named argument ("size") for the call
template ("%c4" to "%c[size]") as already used in the other call
templates in this file.
Found after moving the usercopy selftests to KUnit:
# usercopy_test_invalid: EXPECTATION FAILED at
lib/usercopy_kunit.c:278
Expected val_u64 == 0, but
val_u64 == -60129542144 (0xfffffff200000000)
Closes: https://lore.kernel.org/all/CABVgOSn=tb=Lj9SxHuT4_9MTjjKVxsq-ikdXC4kGHO4CfKVmGQ@mail.gmail.com Fixes: b19b74bc99b1 ("x86/mm: Rework address range check in get_user() and put_user()") Reported-by: David Gow <davidgow@google.com> Signed-off-by: Kees Cook <kees@kernel.org> Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com> Reviewed-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Reviewed-by: Qiuxu Zhuo <qiuxu.zhuo@intel.com> Tested-by: David Gow <davidgow@google.com> Link: https://lore.kernel.org/all/20240610210213.work.143-kees%40kernel.org Signed-off-by: Sasha Levin <sashal@kernel.org>
The "P" asm operand modifier is a x86 target-specific modifier.
When used with a constant, the "P" modifier emits "cst" instead of
"$cst". This property is currently used to emit the bare constant
without all syntax-specific prefixes.
The generic "c" resp. "n" operand modifier should be used instead.
Lion Ackermann reported that there is a race condition between namespace cleanup
in ipset and the garbage collection of the list:set type. The namespace
cleanup can destroy the list:set type of sets while the gc of the set type is
waiting to run in rcu cleanup. The latter uses data from the destroyed set which
thus leads use after free. The patch contains the following parts:
- When destroying all sets, first remove the garbage collectors, then wait
if needed and then destroy the sets.
- Fix the badly ordered "wait then remove gc" for the destroy a single set
case.
- Fix the missing rcu locking in the list:set type in the userspace test
case.
- Use proper RCU list handlings in the list:set type.
The patch depends on c1193d9bbbd3 (netfilter: ipset: Add list flush to cancel_gc).
Check for mandatory netlink attributes in payload and meta expression
when used embedded from the inner expression, otherwise NULL pointer
dereference is possible from userspace.
Fixes: a150d122b6bd ("netfilter: nft_meta: add inner match support") Fixes: 3a07327d10a0 ("netfilter: nft_inner: support for inner tunnel header matching") Signed-off-by: Davide Ornaghi <d.ornaghi97@gmail.com> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
If the card doesn't have display hardware, hpd_work and hpd_lock are
left uninitialized which causes BUG when attempting to schedule hpd_work
on runtime PM resume.
Fix it by adding headless flag to DRM and skip any hpd if it's set.
Due to timer wheel implementation, a timer will usually fire
after its schedule.
For instance, for HZ=1000, a timeout between 512ms and 4s
has a granularity of 64ms.
For this range of values, the extra delay could be up to 63ms.
For TCP, this means that tp->rcv_tstamp may be after
inet_csk(sk)->icsk_timeout whenever the timer interrupt
finally triggers, if one packet came during the extra delay.
We need to make sure tcp_rtx_probe0_timed_out() handles this case.
Fixes: e89688e3e978 ("net: tcp: fix unexcepted socket die when snd_wnd is 0") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Menglong Dong <imagedong@tencent.com> Acked-by: Neal Cardwell <ncardwell@google.com> Reviewed-by: Jason Xing <kerneljasonxing@gmail.com> Link: https://lore.kernel.org/r/20240607125652.1472540-1-edumazet@google.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When the noop_qdisc owner isn't initialized, then it will be 0,
so packets will erroneously be regarded as having been subject
to recursion as long as only CPU 0 queues them. For non-SMP,
that's all packets, of course. This causes a change in what's
reported to userspace, normally noop_qdisc would drop packets
silently, but with this change the syscall returns -ENOBUFS if
RECVERR is also set on the socket.
Fix this by initializing the owner field to -1, just like it
would be for dynamically allocated qdiscs by qdisc_alloc().
The amp_id argument of l2cap_connect() was removed in
commit 84a4bb6548a2 ("Bluetooth: HCI: Remove HCI_AMP support")
It was always called with amp_id == 0, i.e. AMP_ID_BREDR == 0x00 (ie.
non-AMP controller). In the above commit, the code path for amp_id != 0
was preserved, although it should have used the amp_id == 0 one.
Restore the previous behavior of the non-AMP code path, to fix problems
with L2CAP connections.
Fixes: 84a4bb6548a2 ("Bluetooth: HCI: Remove HCI_AMP support") Signed-off-by: Pauli Virtanen <pav@iki.fi> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
This removes the bogus check for max > hcon->le_conn_max_interval since
the later is just the initial maximum conn interval not the maximum the
stack could support which is really 3200=4000ms.
In order to pass GAP/CONN/CPUP/BV-05-C one shall probably enter values
of the following fields in IXIT that would cause hci_check_conn_params
to fail:
Link: https://github.com/bluez/bluez/issues/847 Fixes: e4b019515f95 ("Bluetooth: Enforce validation on max value of connection interval") Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Move the vxlan_features_check() call to after we verified the packet is
a tunneled VXLAN packet.
Without this, tunneled UDP non-VXLAN packets (for ex. GENENVE) might
wrongly not get offloaded.
In some cases, it worked by chance as GENEVE header is the same size as
VXLAN, but it is obviously incorrect.
Fixes: e3cfc7e6b7bd ("net/mlx5e: TX, Add geneve tunnel stateless offload support") Signed-off-by: Gal Pressman <gal@nvidia.com> Reviewed-by: Dragos Tatulea <dtatulea@nvidia.com> Signed-off-by: Tariq Toukan <tariqt@nvidia.com> Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
When innerprotoinherit is set, the tunneled packets do not have an inner
Ethernet header.
Change 'maclen' to not always assume the header length is ETH_HLEN, as
there might not be a MAC header.
This resolves issues with drivers (e.g. mlx5, in
mlx5e_tx_tunnel_accel()) who rely on the skb inner network header offset
to be correct, and use it for TX offloads.
Fixes: d8a6213d70ac ("geneve: fix header validation in geneve[6]_xmit_skb") Signed-off-by: Gal Pressman <gal@nvidia.com> Signed-off-by: Tariq Toukan <tariqt@nvidia.com> Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
tcp_v6_syn_recv_sock() calls ip6_dst_store() before
inet_sk(newsk)->pinet6 has been set up.
This means ip6_dst_store() writes over the parent (listener)
np->dst_cookie.
This is racy because multiple threads could share the same
parent and their final np->dst_cookie could be wrong.
Move ip6_dst_store() call after inet_sk(newsk)->pinet6
has been changed and after the copy of parent ipv6_pinfo.
Fixes: e994b2f0fb92 ("tcp: do not lock listener to process SYN packets") Signed-off-by: Eric Dumazet <edumazet@google.com> Reviewed-by: Simon Horman <horms@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Device managed panel bridge wrappers are created by calling to
drm_panel_bridge_add_typed() and registering a release handler for
clean-up when the device gets unbound.
Since the memory for this bridge is also managed and linked to the panel
device, the release function should not try to free that memory.
Moreover, the call to devm_kfree() inside drm_panel_bridge_remove() will
fail in this case and emit a warning because the panel bridge resource
is no longer on the device resources list (it has been removed from
there before the call to release handlers).
The default ndo_get_iflink() implementation returns the current ifindex
of the netdev. But the overridden nsim_get_iflink() returns 0 if the
current nsim is not linked, breaking backwards compatibility for
userspace that depend on this behaviour.
Fix the problem by returning the current ifindex if not linked to a
peer.
Fixes: 8debcf5832c3 ("netdevsim: add ndo_get_iflink() implementation") Reported-by: Yu Watanabe <watanabe.yu@gmail.com> Suggested-by: Yu Watanabe <watanabe.yu@gmail.com> Signed-off-by: David Wei <dw@davidwei.uk> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit 070246e4674b ("net: stmmac: Fix for mismatched host/device DMA
address width") added support in the stmmac driver for platform drivers
to indicate the host DMA width, but left it up to authors of the
specific platforms to indicate if their width differed from the addr64
register read from the MAC itself.
Qualcomm's EMAC4 integration supports only up to 36 bit width (as
opposed to the addr64 register indicating 40 bit width). Let's indicate
that in the platform driver to avoid a scenario where the driver will
allocate descriptors of size that is supported by the CPU which in our
case is 36 bit, but as the addr64 register is still capable of 40 bits
the device will use two descriptors as one address.
Fixes: 8c4d92e82d50 ("net: stmmac: dwmac-qcom-ethqos: add support for emac4 on sa8775p platforms") Signed-off-by: Sagar Cheluvegowda <quic_scheluve@quicinc.com> Reviewed-by: Simon Horman <horms@kernel.org> Reviewed-by: Andrew Halaney <ahalaney@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
In lio_vf_rep_copy_packet() pg_info->page is compared to a NULL value,
but then it is unconditionally passed to skb_add_rx_frag() which looks
strange and could lead to null pointer dereference.
lio_vf_rep_copy_packet() call trace looks like:
octeon_droq_process_packets
octeon_droq_fast_process_packets
octeon_droq_dispatch_pkt
octeon_create_recv_info
...search in the dispatch_list...
->disp_fn(rdisp->rinfo, ...)
lio_vf_rep_pkt_recv(struct octeon_recv_info *recv_info, ...)
In this path there is no code which sets pg_info->page to NULL.
So this check looks unneeded and doesn't solve potential problem.
But I guess the author had reason to add a check and I have no such card
and can't do real test.
In addition, the code in the function liquidio_push_packet() in
liquidio/lio_core.c does exactly the same.
Based on this, I consider the most acceptable compromise solution to
adjust this issue by moving skb_add_rx_frag() into conditional scope.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 1f233f327913 ("liquidio: switchdev support for LiquidIO NIC") Signed-off-by: Aleksandr Mishin <amishin@t-argos.ru> Reviewed-by: Simon Horman <horms@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
It is reported that commit 31a0fa0019b0 ("thermal/debugfs: Pass cooling
device state to thermal_debug_cdev_add()") causes the ACPI fan driver
to fail probing on some systems which turns out to be due to the _FST
control method returning an invalid value until _FSL is first evaluated
for the given fan. If this happens, the .get_cur_state() cooling device
callback returns an error and __thermal_cooling_device_register() fails
as uses that callback after commit 31a0fa0019b0.
Arguably, _FST should not return an invalid value even if it is
evaluated before _FSL, so this may be regarded as a platform firmware
issue, but at the same time it is not a good enough reason for failing
the cooling device registration where the initial cooling device state
is only needed to initialize a thermal debug facility.
Accordingly, modify __thermal_cooling_device_register() to avoid
calling thermal_debug_cdev_add() instead of returning an error if the
initial .get_cur_state() callback invocation fails.
Fixes: 31a0fa0019b0 ("thermal/debugfs: Pass cooling device state to thermal_debug_cdev_add()") Closes: https://lore.kernel.org/linux-acpi/20240530153727.843378-1-laura.nao@collabora.com Reported-by: Laura Nao <laura.nao@collabora.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org> Tested-by: Laura Nao <laura.nao@collabora.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently hns3 ring buffer init process would hold cpu too long with big
Tx/Rx ring depth. This could cause soft lockup.
So this patch adds cond_resched() to the process. Then cpu can break to
run other tasks instead of busy looping.
Fixes: a723fb8efe29 ("net: hns3: refine for set ring parameters") Signed-off-by: Jie Wang <wangjie125@huawei.com> Signed-off-by: Jijie Shao <shaojijie@huawei.com> Reviewed-by: Simon Horman <horms@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
When link status change, the nic driver need to notify the roce
driver to handle this event, but at this time, the roce driver
may uninit, then cause kernel crash.
To fix the problem, when link status change, need to check
whether the roce registered, and when uninit, need to wait link
update finish.
Fixes: 45e92b7e4e27 ("net: hns3: add calling roce callback function when link status change") Signed-off-by: Yonglong Liu <liuyonglong@huawei.com> Signed-off-by: Jijie Shao <shaojijie@huawei.com> Reviewed-by: Simon Horman <horms@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
If the module is in SFP_MOD_ERROR, `sfp_sm_mod_remove()` will
not be run. As a consequence, `sfp_hwmon_remove()` is not getting
run either, leaving a stale `hwmon` device behind. `sfp_sm_mod_remove()`
itself checks `sfp->sm_mod_state` anyways, so this check was not
really needed in the first place.
Fixes: d2e816c0293f ("net: sfp: handle module remove outside state machine") Signed-off-by: "Csókás, Bence" <csokas.bence@prolan.hu> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://lore.kernel.org/r/20240605084251.63502-1-csokas.bence@prolan.hu Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / thirdparty / kernel / stable.git / log
