The driver neglects to check the result of platform_get_irq()'s call and
blithely passes the negative error codes to devm_request_irq() (which
takes *unsigned* IRQ #), causing it to fail with -EINVAL, overriding
an original error code. Stop calling devm_request_irq() with invalid
IRQ #s.
The driver neglects to check the result of platform_get_irq()'s call and
blithely passes the negative error codes to devm_request_irq() (which
takes *unsigned* IRQ #), causing it to fail with -EINVAL, overriding
an original error code. Stop calling devm_request_irq() with invalid
IRQ #s.
The shifting of the u8 integers rq->caching by 26 bits to
the left will be promoted to a 32 bit signed int and then
sign-extended to a u64. In the event that rq->caching is
greater than 0x1f then all then all the upper 32 bits of
the u64 end up as also being set because of the int
sign-extension. Fix this by casting the u8 values to a
u64 before the 26 bit left shift.
Addresses-Coverity: ("Unintended sign extension") Fixes: 4863dea3fab0 ("net: Adding support for Cavium ThunderX network controller") Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently the expression ~nic_conf1 is always true because nic_conf1
is a u16 and according to 6.5.3.3 of the C standard the ~ operator
promotes the u16 to an integer before flipping all the bits. Thus
the top 16 bits of the integer result are all set so the expression
is always true. If the intention was to flip all the bits of nic_conf1
then casting the integer result back to a u16 is a suitabel fix.
Interestingly static analyzers seem to thing a bitwise ! should be
used instead of ~ for this scenario, so I think the original intent
of the expression may need some extra consideration.
Addresses-Coverity: ("Logical vs. bitwise operator") Fixes: c869f77d6abb ("add mt7601u driver") Signed-off-by: Colin Ian King <colin.king@canonical.com> Acked-by: Jakub Kicinski <kubakici@wp.pl> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20210225183241.1002129-1-colin.king@canonical.com Signed-off-by: Sasha Levin <sashal@kernel.org>
If any of the cipher schemes specified by the driver are invalid, bail
out and fail the registration rather than just warning. Otherwise, we
might later crash when we try to use the invalid cipher scheme, e.g.
if the hdr_len is (significantly) less than the pn_offs + pn_len, we'd
have an out-of-bounds access in RX validation.
When neither CONFIG_PCI nor CONFIG_IBMVIO is set/enabled, iommu.c has a
build error. The fault injection code is not useful in that kernel config,
so make the FAIL_IOMMU option depend on PCI || IBMVIO.
Prevents this build error (warning escalated to error):
../arch/powerpc/kernel/iommu.c:178:30: error: 'fail_iommu_bus_notifier' defined but not used [-Werror=unused-variable]
178 | static struct notifier_block fail_iommu_bus_notifier = {
Fixes: d6b9a81b2a45 ("powerpc: IOMMU fault injection") Reported-by: kernel test robot <lkp@intel.com> Suggested-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Acked-by: Randy Dunlap <rdunlap@infradead.org> # build-tested Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20210404192623.10697-1-rdunlap@infradead.org Signed-off-by: Sasha Levin <sashal@kernel.org>
The power PMU group constraints includes check for EBB events to make
sure all events in a group must agree on EBB. This will prevent
scheduling EBB and non-EBB events together. But in the existing check,
settings for constraint mask and value is interchanged. Patch fixes the
same.
Before the patch, PMU selftest "cpu_event_pinned_vs_ebb_test" fails with
below in dmesg logs. This happens because EBB event gets enabled along
with a non-EBB cpu event.
[35600.453346] cpu_event_pinne[41326]: illegal instruction (4)
at 10004a18 nip 10004a18 lr 100049f8 code 1 in
cpu_event_pinned_vs_ebb_test[10000000+10000]
Test results after the patch:
$ ./pmu/ebb/cpu_event_pinned_vs_ebb_test
test: cpu_event_pinned_vs_ebb
tags: git_version:v5.12-rc5-93-gf28c3125acd3-dirty
Binding to cpu 8
EBB Handler is at 0x100050c8
read error on event 0x7fffe6bd4040!
PM_RUN_INST_CMPL: result 9872 running/enabled 37930432
success: cpu_event_pinned_vs_ebb
This bug was hidden by other logic until commit 1908dc911792 (perf:
Tweak perf_event_attr::exclusive semantics).
When adding a PTE a ptesync is needed to order the update of the PTE
with subsequent accesses otherwise a spurious fault may be raised.
radix__set_pte_at() does not do this for performance gains. For
non-kernel memory this is not an issue as any faults of this kind are
corrected by the page fault handler. For kernel memory these faults
are not handled. The current solution is that there is a ptesync in
flush_cache_vmap() which should be called when mapping from the
vmalloc region.
However, map_kernel_page() does not call flush_cache_vmap(). This is
troublesome in particular for code patching with Strict RWX on radix.
In do_patch_instruction() the page frame that contains the instruction
to be patched is mapped and then immediately patched. With no ordering
or synchronization between setting up the PTE and writing to the page
it is possible for faults.
As the code patching is done using __put_user_asm_goto() the resulting
fault is obscured - but using a normal store instead it can be seen:
This results in the kind of issue reported here:
https://lore.kernel.org/linuxppc-dev/15AC5B0E-A221-4B8C-9039-FA96B8EF7C88@lca.pw/
Chris Riedl suggested a reliable way to reproduce the issue:
$ mount -t debugfs none /sys/kernel/debug
$ (while true; do echo function > /sys/kernel/debug/tracing/current_tracer ; echo nop > /sys/kernel/debug/tracing/current_tracer ; done) &
Turning ftrace on and off does a large amount of code patching which
in usually less then 5min will crash giving a trace like:
The macro CN23XX_PEM_BAR1_INDEX_REG is being used to shift oct->pcie_port
(a u16) left 24 places. There are two subtle issues here, first the
shift gets promoted to an signed int and then sign extended to a u64.
If oct->pcie_port is 0x80 or more then the upper bits get sign extended
to 1. Secondly shfiting a u16 24 bits will lead to an overflow so it
needs to be cast to a u64 for all the bits to not overflow.
It is entirely possible that the u16 port value is never large enough
for this to fail, but it is useful to fix unintended overflows such
as this.
Fix this by casting the port parameter to the macro to a u64 before
the shift.
Addresses-Coverity: ("Unintended sign extension") Fixes: 5bc67f587ba7 ("liquidio: CN23XX register definitions") Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
There are a few calls of usb_driver_claim_interface() but all of those
miss the proper error checks, as reported by Coverity. This patch
adds those missing checks.
Along with it, replace the magic pointer with -1 with a constant
USB_AUDIO_IFACE_UNUSED for better readability.
Fixes: c3b1e1e8a76f ("NFC: Export NFCID1 from pn533") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
report_bug() will return early if it cannot find a bug corresponding to
the provided address. The subsequent test for the bug will always be
true so remove it.
Fixes: 1b4cfe3c0a30d ("lib/bug.c: exclude non-BUG/WARN exceptions from report_bug()") Signed-off-by: Andrew Scull <ascull@google.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: "Steven Rostedt (VMware)" <rostedt@goodmis.org> Reviewed-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Acked-by: Will Deacon <will@kernel.org> Signed-off-by: Marc Zyngier <maz@kernel.org> Link: https://lore.kernel.org/r/20210318143311.839894-2-ascull@google.com Signed-off-by: Sasha Levin <sashal@kernel.org>
If identical_pvr_fixup() is not inlined, there are two modpost warnings:
WARNING: modpost: vmlinux.o(.text+0x54e8): Section mismatch in reference
from the function identical_pvr_fixup() to the function
.init.text:of_get_flat_dt_prop()
The function identical_pvr_fixup() references
the function __init of_get_flat_dt_prop().
This is often because identical_pvr_fixup lacks a __init
annotation or the annotation of of_get_flat_dt_prop is wrong.
WARNING: modpost: vmlinux.o(.text+0x551c): Section mismatch in reference
from the function identical_pvr_fixup() to the function
.init.text:identify_cpu()
The function identical_pvr_fixup() references
the function __init identify_cpu().
This is often because identical_pvr_fixup lacks a __init
annotation or the annotation of identify_cpu is wrong.
identical_pvr_fixup() calls two functions marked as __init and is only
called by a function marked as __init so it should be marked as __init
as well. At the same time, remove the inline keywork as it is not
necessary to inline this function. The compiler is still free to do so
if it feels it is worthwhile since commit 889b3c1245de ("compiler:
remove CONFIG_OPTIMIZE_INLINING entirely").
There are two "netif_running" checks in this driver. One is in
"lapbeth_xmit" and the other is in "lapbeth_rcv". They serve to make
sure that the LAPB APIs called in these functions are called before
"lapb_unregister" is called by the "ndo_stop" function.
However, these "netif_running" checks are unreliable, because it's
possible that immediately after "netif_running" returns true, "ndo_stop"
is called (which causes "lapb_unregister" to be called).
This patch adds locking to make sure "lapbeth_xmit" and "lapbeth_rcv" can
reliably check and ensure the netif is running while doing their work.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Xie He <xie.he.0141@gmail.com> Acked-by: Martin Schiller <ms@dev.tdt.de> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The 'ret' variable was initialized to zero but then it was not updated
from the fprintf() return, fix it.
Reported-by: Yang Li <yang.lee@linux.alibaba.com>
cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
cc: Ingo Molnar <mingo@redhat.com>
cc: Jiri Olsa <jolsa@redhat.com>
cc: Mark Rutland <mark.rutland@arm.com>
cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Srikar Dronamraju <srikar@linux.vnet.ibm.com> Fixes: 90f18e63fbd00513 ("perf symbols: List symbols in a dso in ascending name order") Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Plantronics Blackwire 3220 Series (047f:c056) sends HID reports twice
for each volume key press. This patch adds a quirk to hid-plantronics
for this product ID, which will ignore the second volume key press if
it happens within 5 ms from the last one that was handled.
The patch was tested on the mentioned model only, it shouldn't affect
other models, however, this quirk might be needed for them too.
Auto-repeat (when a key is held pressed) is not affected, because the
rate is about 3 times per second, which is far less frequent than once
in 5 ms.
In null_init, null_add_dev(dev) is called.
In null_add_dev, it calls null_free_zoned_dev(dev) to free dev->zones
via kvfree(dev->zones) in out_cleanup_zone branch and returns err.
Then null_init accept the err code and then calls null_free_dev(dev).
But in null_free_dev(dev), dev->zones is freed again by
null_free_zoned_dev().
My patch set dev->zones to NULL in null_free_zoned_dev() after
kvfree(dev->zones) is called, to avoid the double free.
The handling of sysrq key can be activated by echoing the key to
/proc/sysrq-trigger or via the magic key sequence typed into a terminal
that is connected to the system in some way (serial, USB or other mean).
In the former case, the handling is done in a user context. In the
latter case, it is likely to be in an interrupt context.
Currently in print_cpu() of kernel/sched/debug.c, sched_debug_lock is
taken with interrupt disabled for the whole duration of the calls to
print_*_stats() and print_rq() which could last for the quite some time
if the information dump happens on the serial console.
If the system has many cpus and the sched_debug_lock is somehow busy
(e.g. parallel sysrq-t), the system may hit a hard lockup panic
depending on the actually serial console implementation of the
system.
The purpose of sched_debug_lock is to serialize the use of the global
cgroup_path[] buffer in print_cpu(). The rests of the printk calls don't
need serialization from sched_debug_lock.
Calling printk() with interrupt disabled can still be problematic if
multiple instances are running. Allocating a stack buffer of PATH_MAX
bytes is not feasible because of the limited size of the kernel stack.
The solution implemented in this patch is to allow only one caller at a
time to use the full size group_path[], while other simultaneous callers
will have to use shorter stack buffers with the possibility of path
name truncation. A "..." suffix will be printed if truncation may have
happened. The cgroup path name is provided for informational purpose
only, so occasional path name truncation should not be a big problem.
Fixes: efe25c2c7b3a ("sched: Reinstate group names in /proc/sched_debug") Suggested-by: Peter Zijlstra <peterz@infradead.org> Signed-off-by: Waiman Long <longman@redhat.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Link: https://lkml.kernel.org/r/20210415195426.6677-1-longman@redhat.com Signed-off-by: Sasha Levin <sashal@kernel.org>
dev_attr_show() calls _iommu_event_show() via an indirect call but
_iommu_event_show()'s type does not currently match the type of the
show() member in 'struct device_attribute', resulting in a Control Flow
Integrity violation.
If some of the allocations fail between the dev_set_name() and the
device_register() then the name will not be freed. Fix this by
moving dev_set_name() directly in front of the call to device_register().
Fixes: a2aa24734d9d ("HSI: Add common DT binding for HSI client devices") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by: Jason Gunthorpe <jgg@nvidia.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The ARR register is cleared unconditionally upon probing, after the maximum
value has been read. This initial condition is rather not intuitive, when
considering the counter child driver. It rather expects the maximum value
by default:
- The counter interface shows a zero value by default for 'ceiling'
attribute.
- Enabling the counter without any prior configuration makes it doesn't
count.
The reset value of ARR register is the maximum. So Choice here
is to backup it, and restore it then, instead of clearing its value.
It also fixes the initial condition seen by the counter driver.
Fixes: d0f949e220fd ("mfd: Add STM32 Timers driver") Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com> Acked-by: William Breathitt Gray <vilhelm.gray@gmail.com> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
This fixes an issue hitting the BUG_ON() in ibmvfc_do_work(). When going
through a host action of IBMVFC_HOST_ACTION_RESET, we change the action to
IBMVFC_HOST_ACTION_TGT_DEL, then drop the host lock, and reset the CRQ,
which changes the host state to IBMVFC_NO_CRQ. If, prior to setting the
host state to IBMVFC_NO_CRQ, ibmvfc_init_host() is called, it can then end
up changing the host action to IBMVFC_HOST_ACTION_INIT. If we then change
the host state to IBMVFC_NO_CRQ, we will then hit the BUG_ON().
Make a couple of changes to avoid this. Leave the host action to be
IBMVFC_HOST_ACTION_RESET or IBMVFC_HOST_ACTION_REENABLE until after we drop
the host lock and reset or reenable the CRQ. Also harden the host state
machine to ensure we cannot leave the reset / reenable state until we've
finished processing the reset or reenable.
Link: https://lore.kernel.org/r/20210413001009.902400-1-tyreld@linux.ibm.com Fixes: 73ee5d867287 ("[SCSI] ibmvfc: Fix soft lockup on resume") Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
[tyreld: added fixes tag] Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
[mkp: fix comment checkpatch warnings] Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The driver neglects to check the result of platform_get_irq()'s call and
blithely passes the negative error codes to request_irq() (which takes
*unsigned* IRQ #s), causing it to fail with -EINVAL (overridden by -ENODEV
further below). Stop calling request_irq() with the invalid IRQ #s.
The driver neglects to check the result of platform_get_irq()'s call and
blithely passes the negative error codes to request_irq() (which takes
*unsigned* IRQ #), causing it to fail with -EINVAL, overriding the real
error code. Stop calling request_irq() with the invalid IRQ #s.
Link: https://lore.kernel.org/r/363eb4c8-a3bf-4dc9-2a9e-90f349030a15@omprussia.ru Fixes: 0bb67f181834 ("[SCSI] sun3x_esp: convert to esp_scsi") Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The driver neglects to check the result of platform_get_irq()'s call and
blithely passes the negative error codes to request_irq() (which takes
*unsigned* IRQ #), causing it to fail with -EINVAL, overriding the real
error code. Stop calling request_irq() with the invalid IRQ #s.
Link: https://lore.kernel.org/r/594aa9ae-2215-49f6-f73c-33bd38989912@omprussia.ru Fixes: 352e921f0dd4 ("[SCSI] jazz_esp: converted to use esp_core") Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The for-loop iterates with a u8 loop counter i and compares this
with the loop upper limit of num_parents that is an int type.
There is a potential infinite loop if num_parents is larger than
the u8 loop counter. Fix this by making the loop counter the same
type as num_parents. Also make num_parents an unsigned int to
match the return type of the call to clk_hw_get_num_parents.
Addresses-Coverity: ("Infinite loop") Fixes: 734d82f4a678 ("clk: uniphier: add core support code for UniPhier clock driver") Signed-off-by: Colin Ian King <colin.king@canonical.com> Reviewed-by: Masahiro Yamada <masahiroy@kernel.org> Link: https://lore.kernel.org/r/20210409090104.629722-1-colin.king@canonical.com Signed-off-by: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
CONFIG_QCOM_A53PLL is tristate option and therefore this driver can be
compiled as a module. This patch adds missing MODULE_DEVICE_TABLE
definition which generates correct modalias for automatic loading of
this driver when it is built as an external module.
If ANA is enabled but no ANA group descriptor is found when creating
a new namespace the ANA log is most likely out of date, so trigger
a re-read. The namespace will be tagged with the NS_ANA_PENDING flag
to exclude it from path selection until the ANA log has been re-read.
Fixes: 32acab3181c7 ("nvme: implement multipath access to nvme subsystems") Reported-by: Martin George <marting@netapp.com> Signed-off-by: Hannes Reinecke <hare@suse.de> Reviewed-by: Keith Busch <kbusch@kernel.org> Reviewed-by: Sagi Grimberg <sagi@grimberg.me> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
Iff platform_get_irq() returns 0, ahci_platform_init_host() would return 0
early (as if the call was successful). Override IRQ0 with -EINVAL instead
as the 'libata' regards 0 as "no IRQ" (thus polling) anyway...
The function mv_platform_probe() neglects to check the results of the
calls to platform_get_irq() and irq_of_parse_and_map() and blithely
passes them to ata_host_activate() -- while the latter only checks
for IRQ0 (treating it as a polling mode indicattion) and passes the
negative values to devm_request_irq() causing it to fail as it takes
unsigned values for the IRQ #...
Add to mv_platform_probe() the proper IRQ checks to pass the positive IRQ
#s to ata_host_activate(), propagate upstream the negative error codes,
and override the IRQ0 with -EINVAL (as we don't want the polling mode).
The driver's probe() method is written as if platform_get_irq() returns 0
on error, while actually it returns a negative error code (with all the
other values considered valid IRQs). Rewrite the driver's IRQ checking
code to pass the positive IRQ #s to ata_host_activate(), propagate errors
upstream, and treat IRQ0 as error, returning -EINVAL, as the libata code
treats 0 as an indication that polling should be used anyway...
The driver's probe() method is written as if platform_get_irq() returns 0
on error, while actually it returns a negative error code (with all the
other values considered valid IRQs). Rewrite the driver's IRQ checking code
to pass the positive IRQ #s to ata_host_activate(), propagate upstream
-EPROBE_DEFER, and set up the driver to polling mode on (negative) errors
and IRQ0 (libata treats IRQ #0 as a polling mode anyway)...
There are 2 bugs in the can_boost() function because of using
x86 insn decoder. Since the insn->opcode never has a prefix byte,
it can not find CS override prefix in it. And the insn->attr is
the attribute of the opcode, thus inat_is_address_size_prefix(
insn->attr) always returns false.
Fix those by checking each prefix bytes with for_each_insn_prefix
loop and getting the correct attribute for each prefix byte.
Also, this removes unlikely, because this is a slow path.
Using 'imply AMD_IOMMU_V2' does not guarantee that the driver can link
against the exported functions. If the GPU driver is built-in but the
IOMMU driver is a loadable module, the kfd_iommu.c file is indeed
built but does not work:
x86_64-linux-ld: drivers/gpu/drm/amd/amdkfd/kfd_iommu.o: in function `kfd_iommu_bind_process_to_device':
kfd_iommu.c:(.text+0x516): undefined reference to `amd_iommu_bind_pasid'
x86_64-linux-ld: drivers/gpu/drm/amd/amdkfd/kfd_iommu.o: in function `kfd_iommu_unbind_process':
kfd_iommu.c:(.text+0x691): undefined reference to `amd_iommu_unbind_pasid'
x86_64-linux-ld: drivers/gpu/drm/amd/amdkfd/kfd_iommu.o: in function `kfd_iommu_suspend':
kfd_iommu.c:(.text+0x966): undefined reference to `amd_iommu_set_invalidate_ctx_cb'
x86_64-linux-ld: kfd_iommu.c:(.text+0x97f): undefined reference to `amd_iommu_set_invalid_ppr_cb'
x86_64-linux-ld: kfd_iommu.c:(.text+0x9a4): undefined reference to `amd_iommu_free_device'
x86_64-linux-ld: drivers/gpu/drm/amd/amdkfd/kfd_iommu.o: in function `kfd_iommu_resume':
kfd_iommu.c:(.text+0xa9a): undefined reference to `amd_iommu_init_device'
x86_64-linux-ld: kfd_iommu.c:(.text+0xadc): undefined reference to `amd_iommu_set_invalidate_ctx_cb'
x86_64-linux-ld: kfd_iommu.c:(.text+0xaff): undefined reference to `amd_iommu_set_invalid_ppr_cb'
x86_64-linux-ld: kfd_iommu.c:(.text+0xc72): undefined reference to `amd_iommu_bind_pasid'
x86_64-linux-ld: kfd_iommu.c:(.text+0xe08): undefined reference to `amd_iommu_set_invalidate_ctx_cb'
x86_64-linux-ld: kfd_iommu.c:(.text+0xe26): undefined reference to `amd_iommu_set_invalid_ppr_cb'
x86_64-linux-ld: kfd_iommu.c:(.text+0xe42): undefined reference to `amd_iommu_free_device'
Use IS_REACHABLE to only build IOMMU-V2 support if the amd_iommu symbols
are reachable by the amdkfd driver. Output a warning if they are not,
because that may not be what the user was expecting.
Fixes: 64d1c3a43a6f ("drm/amdkfd: Centralize IOMMUv2 code and make it conditional") Reported-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
There a 3 array for-loops that don't check the upper bounds of the
index into arrays and this may lead to potential out-of-bounds
reads. Fix this by adding array size upper bounds checks to be
full safe.
Addresses-Coverity: ("Out-of-bounds read")
Link: https://lore.kernel.org/linux-media/20201007121628.20676-1-colin.king@canonical.com Fixes: 333829110f1d ("[media] m88rs6000t: add new dvb-s/s2 tuner for integrated chip M88RS6000") Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently the chroma_flags and alpha_flags are being zero'd with a bit-wise
mask and the following statement should be bit-wise or'ing in the new flag
bits but instead is making a direct assignment. Fix this by using the |=
operator rather than an assignment.
Addresses-Coverity: ("Unused value")
Fixes: ef834f7836ec ("[media] vivid: add the video capture and output parts") Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The intent here was to return negative error codes but it actually
returns positive values. The problem is that type promotion with
ternary operations is quite complicated.
"ret" is an int. "copied" is a u32. And the snoop_file_read() function
returns long. What happens is that "ret" is cast to u32 and becomes
positive then it's cast to long and it's still positive.
Fix this by removing the ternary so that "ret" is type promoted directly
to long.
int main(int argc, char *argv[])
{
int i;
int fd[10];
for (i = 0; i < 10; i++)
fd[i] = open("/dev/ttyprintk", O_WRONLY);
ioctl(fd[0], TIOCVHANGUP);
for (i = 0; i < 10; i++)
close(fd[i]);
close(open("/dev/ttyprintk", O_WRONLY));
return 0;
}
----------
When TTY hangup happens, port->count needs to be reset via
"struct tty_operations"->hangup callback.
When core is in hibernation in host mode and a device cable
was connected then driver exited from device hibernation.
However, registers saved for host mode and when exited from
device hibernation register restore would be done for device
register which was wrong because there was no device registers
stored to restore.
- Added dwc_handle_gpwrdn_disc_det() function which handles
gpwrdn disconnect detect flow and exits hibernation
without restoring the registers.
- Updated exiting from hibernation in GPWRDN_STS_CHGINT with
calling dwc_handle_gpwrdn_disc_det() function. Here no register
is restored which is the solution described above.
Added setting "port_connect_status_change" flag to "1" in order
to re-enumerate, because after exit from hibernation port
connection status is not detected.
When running in Azure, disks may be connected to a Linux VM with
read/write caching enabled. If a VM panics and issues a VMbus
UNLOAD request to Hyper-V, the response is delayed until all dirty
data in the disk cache is flushed. In extreme cases, this flushing
can take 10's of seconds, depending on the disk speed and the amount
of dirty data. If kdump is configured for the VM, the current 10 second
timeout in vmbus_wait_for_unload() may be exceeded, and the UNLOAD
complete message may arrive well after the kdump kernel is already
running, causing problems. Note that no problem occurs if kdump is
not enabled because Hyper-V waits for the cache flush before doing
a reboot through the BIOS/UEFI code.
Fix this problem by increasing the timeout in vmbus_wait_for_unload()
to 100 seconds. Also output periodic messages so that if anyone is
watching the serial console, they won't think the VM is completely
hung.
Fixes: 911e1987efc8 ("Drivers: hv: vmbus: Add timeout to vmbus_wait_for_unload") Signed-off-by: Michael Kelley <mikelley@microsoft.com> Reviewed-by: Vitaly Kuznetsov <vkuznets@redhat.com> Link: https://lore.kernel.org/r/1618894089-126662-1-git-send-email-mikelley@microsoft.com Signed-off-by: Wei Liu <wei.liu@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
arch/x86/platform/uv/uv_nmi.c:875:14: error: ‘uv_nmi_kexec_failed’ undeclared (first use in this function)
Since uv_nmi_kexec_failed is only defined in the KEXEC_CORE #ifdef branch,
this code cannot ever have been build tested:
if (main)
pr_err("UV: NMI kdump: KEXEC not supported in this kernel\n");
atomic_set(&uv_nmi_kexec_failed, 1);
Nor is this use possible in uv_handle_nmi():
atomic_set(&uv_nmi_kexec_failed, 0);
These bugs were introduced in this commit:
d0a9964e9873: ("x86/platform/uv: Implement simple dump failover if kdump fails")
Which added the uv_nmi_kexec_failed assignments to !KEXEC code, while making the
definition KEXEC-only - apparently without testing the !KEXEC case.
Instead of complicating the #ifdef maze, simplify the code by requiring X86_UV
to depend on KEXEC_CORE. This pattern is present in other architectures as well.
( We'll remove the untested, 7 years old !KEXEC complications from the file in a
separate commit. )
pmc_plt_clk* clocks are used for ethernet controllers, so need to stay
turned on. This adds the affected board family to critclk_systems DMI
table, so the clocks are marked as CLK_CRITICAL and not turned off.
This replaces the previously listed boards with a match for the whole
device family CBxx63. CBxx63 matches only baytrail devices.
There are new affected boards that would otherwise need to be listed.
There are unaffected boards in the family, but having the clocks
turned on is not an issue.
Fixes: 648e921888ad ("clk: x86: Stop marking clocks as CLK_IS_CRITICAL") Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Signed-off-by: Steffen Dirkwinkel <s.dirkwinkel@beckhoff.com> Link: https://lore.kernel.org/r/20210412133006.397679-1-linux-kernel-dev@beckhoff.com Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When CONFIG_QCOM_SCM is y and CONFIG_HAVE_ARM_SMCCC
is not set, compiling errors are encountered as follows:
drivers/firmware/qcom_scm-smc.o: In function `__scm_smc_do_quirk':
qcom_scm-smc.c:(.text+0x36): undefined reference to `__arm_smccc_smc'
drivers/firmware/qcom_scm-legacy.o: In function `scm_legacy_call':
qcom_scm-legacy.c:(.text+0xe2): undefined reference to `__arm_smccc_smc'
drivers/firmware/qcom_scm-legacy.o: In function `scm_legacy_call_atomic':
qcom_scm-legacy.c:(.text+0x1f0): undefined reference to `__arm_smccc_smc'
Note that __arm_smccc_smc is defined when HAVE_ARM_SMCCC is y.
So add dependency on HAVE_ARM_SMCCC in QCOM_SCM configuration.
Fixes: 916f743da354 ("firmware: qcom: scm: Move the scm driver to drivers/firmware") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: He Ying <heying24@huawei.com> Link: https://lore.kernel.org/r/20210406094200.60952-1-heying24@huawei.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
TIOCSSERIAL is a horrid, underspecified, legacy interface which for most
serial devices is only useful for setting the close_delay and
closing_wait parameters.
A non-privileged user has only ever been able to set the since long
deprecated ASYNC_SPD flags and trying to change any other *supported*
feature should result in -EPERM being returned. Setting the current
values for any supported features should return success.
Fix the cdc-acm implementation which instead indicated that the
TIOCSSERIAL ioctl was not even implemented when a non-privileged user
set the current values.
Fixes: ba2d8ce9db0a ("cdc-acm: implement TIOCSSERIAL to avoid blocking close(2)") Acked-by: Oliver Neukum <oneukum@suse.com> Signed-off-by: Johan Hovold <johan@kernel.org> Link: https://lore.kernel.org/r/20210408131602.27956-3-johan@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When current CPU load is not L0 then loading armada-37xx-cpufreq.ko driver
fails with following error:
# modprobe armada-37xx-cpufreq
[ 502.702097] Unsupported CPU frequency 250 MHz
This issue was partially fixed by commit 8db82563451f ("cpufreq:
armada-37xx: fix frequency calculation for opp"), but only for calculating
CPU frequency for opp.
Fix this also for determination of base CPU frequency.
Signed-off-by: Pali Rohár <pali@kernel.org> Acked-by: Gregory CLEMENT <gregory.clement@bootlin.com> Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com> Tested-by: Anders Trier Olesen <anders.trier.olesen@gmail.com> Tested-by: Philip Soares <philips@netisense.com> Fixes: 92ce45fb875d ("cpufreq: Add DVFS support for Armada 37xx") Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit 8db82563451f ("cpufreq: armada-37xx: fix frequency calculation for
opp") changed calculation of frequency passed to the dev_pm_opp_add()
function call. But the code for dev_pm_opp_remove() function call was not
updated, so the driver cleanup phase does not work when registration fails.
This fixes the issue by using the same frequency in both calls.
Signed-off-by: Pali Rohár <pali@kernel.org> Acked-by: Gregory CLEMENT <gregory.clement@bootlin.com> Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com> Tested-by: Anders Trier Olesen <anders.trier.olesen@gmail.com> Tested-by: Philip Soares <philips@netisense.com> Fixes: 8db82563451f ("cpufreq: armada-37xx: fix frequency calculation for opp") Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When CPU frequency is at 250 MHz and set_rate() is called with 500 MHz (L1)
quickly followed by a call with 1 GHz (L0), the CPU does not necessarily
stay in L1 for at least 20ms as is required by Marvell errata.
This situation happens frequently with the ondemand cpufreq governor and
can be also reproduced with userspace governor. In most cases it causes CPU
to crash.
This change fixes the above issue and ensures that the CPU always stays in
L1 for at least 20ms when switching from any state to L0.
Signed-off-by: Marek Behún <kabel@kernel.org> Signed-off-by: Pali Rohár <pali@kernel.org> Acked-by: Stephen Boyd <sboyd@kernel.org> Acked-by: Gregory CLEMENT <gregory.clement@bootlin.com> Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com> Tested-by: Anders Trier Olesen <anders.trier.olesen@gmail.com> Tested-by: Philip Soares <philips@netisense.com> Fixes: 61c40f35f5cd ("clk: mvebu: armada-37xx-periph: Fix switching CPU rate from 300Mhz to 1.2GHz") Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
It was observed that the workaround introduced by commit 61c40f35f5cd
("clk: mvebu: armada-37xx-periph: Fix switching CPU rate from 300Mhz to
1.2GHz") when base CPU frequency is 1.2 GHz is also required when base
CPU frequency is 1 GHz. Otherwise switching CPU frequency directly from
L2 (250 MHz) to L0 (1 GHz) causes a crash.
When base CPU frequency is just 800 MHz no crashed were observed during
switch from L2 to L0.
Signed-off-by: Pali Rohár <pali@kernel.org> Acked-by: Stephen Boyd <sboyd@kernel.org> Acked-by: Gregory CLEMENT <gregory.clement@bootlin.com> Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com> Tested-by: Anders Trier Olesen <anders.trier.olesen@gmail.com> Tested-by: Philip Soares <philips@netisense.com> Fixes: 2089dc33ea0e ("clk: mvebu: armada-37xx-periph: add DVFS support for cpu clocks") Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The original CPU voltage value for load L1 is too low for Armada 37xx SoC
when base CPU frequency is 1000 or 1200 MHz. It leads to instabilities
where CPU gets stuck soon after dynamic voltage scaling from load L1 to L0.
Update the CPU voltage value for load L1 accordingly when base frequency is
1000 or 1200 MHz. The minimal L1 value for base CPU frequency 1000 MHz is
updated from the original 1.05V to 1.108V and for 1200 MHz is updated to
1.155V. This minimal L1 value is used only in the case when it is lower
than value for L0.
This change fixes CPU instability issues on 1 GHz and 1.2 GHz variants of
Espressobin and 1 GHz Turris Mox.
Marvell previously for 1 GHz variant of Espressobin provided a patch [1]
suitable only for their Marvell Linux kernel 4.4 fork which workarounded
this issue. Patch forced CPU voltage value to 1.108V in all loads. But
such change does not fix CPU instability issues on 1.2 GHz variants of
Armada 3720 SoC.
During testing we come to the conclusion that using 1.108V as minimal
value for L1 load makes 1 GHz variants of Espressobin and Turris Mox boards
stable. And similarly 1.155V for 1.2 GHz variant of Espressobin.
These two values 1.108V and 1.155V are documented in Armada 3700 Hardware
Specifications as typical initial CPU voltage values.
Discussion about this issue is also at the Armbian forum [2].
This method was supposed to be needed by the armada-37xx-cpufreq driver,
but was never actually called due to wrong assumptions in the cpufreq
driver. After this was fixed in the cpufreq driver, this method is not
needed anymore.
Signed-off-by: Marek Behún <kabel@kernel.org> Acked-by: Stephen Boyd <sboyd@kernel.org> Acked-by: Gregory CLEMENT <gregory.clement@bootlin.com> Tested-by: Pali Rohár <pali@kernel.org> Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com> Tested-by: Anders Trier Olesen <anders.trier.olesen@gmail.com> Tested-by: Philip Soares <philips@netisense.com> Fixes: 2089dc33ea0e ("clk: mvebu: armada-37xx-periph: add DVFS support for cpu clocks") Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
With CPU frequency determining software [1] we have discovered that
after this driver does one CPU frequency change, the base frequency of
the CPU is set to the frequency of TBG-A-P clock, instead of the TBG
that is parent to the CPU.
This can be reproduced on EspressoBIN and Turris MOX:
cd /sys/devices/system/cpu/cpufreq/policy0
echo powersave >scaling_governor
echo performance >scaling_governor
Running the mhz tool before this driver is loaded reports 1000 MHz, and
after loading the driver and executing commands above the tool reports
800 MHz.
The change of TBG clock selector is supposed to happen in function
armada37xx_cpufreq_dvfs_setup. Before the function returns, it does
this:
parent = clk_get_parent(clk);
clk_set_parent(clk, parent);
The armada-37xx-periph clock driver has the .set_parent method
implemented correctly for this, so if the method was actually called,
this would work. But since the introduction of the common clock
framework in commit b2476490ef11 ("clk: introduce the common clock..."),
the clk_set_parent function checks whether the parent is actually
changing, and if the requested new parent is same as the old parent
(which is obviously the case for the code above), the .set_parent method
is not called at all.
This patch fixes this issue by filling the correct TBG clock selector
directly in the armada37xx_cpufreq_dvfs_setup during the filling of
other registers at the same address. But the determination of CPU TBG
index cannot be done via the common clock framework, therefore we need
to access the North Bridge Peripheral Clock registers directly in this
driver.
[1] https://github.com/wtarreau/mhz
Signed-off-by: Marek Behún <kabel@kernel.org> Acked-by: Gregory CLEMENT <gregory.clement@bootlin.com> Tested-by: Pali Rohár <pali@kernel.org> Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com> Tested-by: Anders Trier Olesen <anders.trier.olesen@gmail.com> Tested-by: Philip Soares <philips@netisense.com> Fixes: 92ce45fb875d ("cpufreq: Add DVFS support for Armada 37xx") Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In adf_create_ring, if the callee adf_init_ring() failed, the callee will
free the ring->base_addr by dma_free_coherent() and return -EFAULT. Then
adf_create_ring will goto err and the ring->base_addr will be freed again
in adf_cleanup_ring().
My patch sets ring->base_addr to NULL after the first freed to avoid the
double free.
As far as I can tell, the only difference between 'struct cppc_attr'
and 'struct kobj_attribute' aside from the type of the attr parameter
is the type of the count parameter in the ->store() member (ssize_t vs.
size_t), which does not actually matter because all of these nodes are
read-only.
Eliminate 'struct cppc_attr' in favor of 'struct kobj_attribute' to fix
the violation.
Given that no validation of how much data the firmware loader read in
for a given segment truncated segment files would best case result in a
hash verification failure, without any indication of what went wrong.
Improve this by validating that the firmware loader did return the
amount of data requested.
The code validates that segments of p_memsz bytes of a segment will fit
in the provided memory region, but does not validate that p_filesz bytes
will, which means that an incorrectly crafted ELF header might write
beyond the provided memory region.
Fixes: 051fb70fd4ea ("remoteproc: qcom: Driver for the self-authenticating Hexagon v5") Reviewed-by: Sibi Sankar <sibis@codeaurora.org> Link: https://lore.kernel.org/r/20210107233119.717173-1-bjorn.andersson@linaro.org Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
We can't rely on the contents of the devres list during
spi_unregister_controller(), as the list is already torn down at the
time we perform devres_find() for devm_spi_release_controller. This
causes devices registered with devm_spi_alloc_{master,slave}() to be
mistakenly identified as legacy, non-devm managed devices and have their
reference counters decremented below 0.
Instead, determine the devm allocation state as a flag on the
controller which is guaranteed to be stable during cleanup.
Fixes: 5e844cc37a5c ("spi: Introduce device-managed SPI controller allocation") Signed-off-by: William A. Kennington III <wak@google.com> Link: https://lore.kernel.org/r/20210407095527.2771582-1-wak@google.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
TIOCSSERIAL is a horrid, underspecified, legacy interface which for most
serial devices is only useful for setting the close_delay and
closing_wait parameters.
A non-privileged user has only ever been able to set the since long
deprecated ASYNC_SPD flags and trying to change any other *supported*
feature should result in -EPERM being returned. Setting the current
values for any supported features should return success.
Fix the greybus implementation which instead indicated that the
TIOCSSERIAL ioctl was not even implemented when a non-privileged user
set the current values.
Fixes: e68453ed28c5 ("greybus: uart-gb: now builds, more framework added") Signed-off-by: Johan Hovold <johan@kernel.org> Link: https://lore.kernel.org/r/20210407102334.32361-7-johan@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The for-loop iterates with a u8 loop counter i and compares this
with the loop upper limit of riv->ieee80211->LinkDetectInfo.SlotNum
that is a u16 type. There is a potential infinite loop if SlotNum
is larger than the u8 loop counter. Fix this by making the loop
counter the same type as SlotNum.
Addresses-Coverity: ("Infinite loop") Fixes: 8fc8598e61f6 ("Staging: Added Realtek rtl8192u driver to staging") Signed-off-by: Colin Ian King <colin.king@canonical.com> Link: https://lore.kernel.org/r/20210407150308.496623-1-colin.king@canonical.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When building with extra warnings enabled, clang points out a
mistake in the error handling:
drivers/irqchip/irq-gic-v3-mbi.c:306:21: error: result of comparison of constant 18446744073709551615 with expression of type 'phys_addr_t' (aka 'unsigned int') is always false [-Werror,-Wtautological-constant-out-of-range-compare]
if (mbi_phys_base == OF_BAD_ADDR) {
Truncate the constant to the same type as the variable it gets compared
to, to shut make the check work and void the warning.
Fixes: 505287525c24 ("irqchip/gic-v3: Add support for Message Based Interrupts as an MSI controller") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Marc Zyngier <maz@kernel.org> Link: https://lore.kernel.org/r/20210323131842.2773094-1-arnd@kernel.org Signed-off-by: Sasha Levin <sashal@kernel.org>
If the callee gpmi_alloc_dma_buffer() failed to alloc memory for
this->raw_buffer, gpmi_free_dma_buffer() will be called to free
this->auxiliary_virt. But this->auxiliary_virt is still a non-NULL
and valid ptr.
Then gpmi_alloc_dma_buffer() returns err and gpmi_free_dma_buffer()
is called again to free this->auxiliary_virt in err_out. This causes
a double free.
As gpmi_free_dma_buffer() has already called in gpmi_alloc_dma_buffer's
error path, so it should return err directly instead of releasing the dma
buffer again.
When stream config is failed, master runtime will release all
slave runtime in the slave_rt_list, but slave runtime is not
added to the list at this time. This patch frees slave runtime
in the config error path to fix the memory leak.
Fixes: 89e590535f32 ("soundwire: Add support for SoundWire stream management") Signed-off-by: Rander Wang <rander.wang@intel.com> Reviewed-by: Keyon Jie <yang.jie@intel.com> Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com> Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com> Link: https://lore.kernel.org/r/20210331004610.12242-1-yung-chuan.liao@linux.intel.com Signed-off-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently the virtual port_dev device is passed to DMA API, and this is
wrong because the device passed to DMA API calls must be the actual
hardware device performing the DMA.
The patch replaces usb_gadget_map_request/usb_gadget_unmap_request APIs
with usb_gadget_map_request_by_dev/usb_gadget_unmap_request_by_dev APIs
so the DMA capable platform device can be passed to the DMA APIs.
The patch fixes below backtrace detected on Facebook AST2500 OpenBMC
platforms:
The function adf_isr_resource_alloc() is not unwinding correctly in case
of error.
This patch fixes the error paths and propagate the errors to the caller.
Fixes: 7afa232e76ce ("crypto: qat - Intel(R) QAT DH895xcc accelerator") Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com> Reviewed-by: Marco Chiappero <marco.chiappero@intel.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
Merely enabling CONFIG_COMPILE_TEST should not enable additional code.
To fix this, restrict the automatic enabling of ARMADA375_USBCLUSTER_PHY
to MACH_ARMADA_375, and ask the user in case of compile-testing.
Fixes: eee47538ec1f2619 ("phy: add support for USB cluster on the Armada 375 SoC") Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Link: https://lore.kernel.org/r/20210208150252.424706-1-geert+renesas@glider.be Signed-off-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
found flag is used to indicate SoundWire devices that are
both enumerated on the bus and available in the device list.
However this flag is not reset correctly after one iteration,
This could miss some of the devices that are enumerated on the
bus but not in device list. So reset this correctly to fix this issue!
Put child node before return to fix potential reference count leak.
Generally, the reference count of child is incremented and decremented
automatically in the macro for_each_available_child_of_node() and should
be decremented manually if the loop is broken in loop body.
MEMLOCK, MEMUNLOCK and OTPLOCK modify protection bits. Thus require
write permission. Depending on the hardware MEMLOCK might even be
write-once, e.g. for SPI-NOR flashes with their WP# tied to GND. OTPLOCK
is always write-once.
MEMSETBADBLOCK modifies the bad block table.
Fixes: f7e6b19bc764 ("mtd: properly check all write ioctls for permissions") Signed-off-by: Michael Walle <michael@walle.cc> Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Acked-by: Rafał Miłecki <rafal@milecki.pl> Acked-by: Richard Weinberger <richard@nod.at> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20210303155735.25887-1-michael@walle.cc Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently it leaves unhandled interrupts unmasked, but those are never
acked. In the case of a "device idle" interrupt, this leads to an
effectively frozen system until plugging it in.
When the EP0 IN request was not completed but less than a packet sent,
it would complete the request successfully. That doesn't make sense
and can't really happen as fotg210_start_dma always sends
min(length, maxpkt) bytes.
For a 134 Byte packet, it sends the first two 64 Byte packets just fine,
but then notice that less than a packet is remaining and call fotg210_done
without actually sending the rest.
For a 75 Byte request, it would send the first 64 separately, then detect
that the remaining 11 Byte fit into a single DMA, but due to this bug set
the length to the original 75 Bytes. This leads to a DMA failure (which is
ignored...) and the request completes without the remaining bytes having
been sent.
ADF_STATUS_PF_RUNNING is (only) used and checked by adf_vf2pf_shutdown()
before calling adf_iov_putmsg()->mutex_lock(vf2pf_lock), however the
vf2pf_lock is initialized in adf_dev_init(), which can fail and when it
fail, the vf2pf_lock is either not initialized or destroyed, a subsequent
use of vf2pf_lock will cause issue.
To fix this issue, only set this flag if adf_dev_init() returns 0.
adf_vf_isr_resource_alloc() is not unwinding correctly when error
happens and it want to release uninitialized resources.
To fix this, only release initialized resources.
DMA mapping might fail, we have to check it with dma_mapping_error().
Otherwise DMA-API is not happy:
DMA-API: pch_udc 0000:02:02.4: device driver failed to check map error[device address=0x00000000027ee678] [size=64 bytes] [mapped as single]
Fixes: abab0c67c061 ("usb: pch_udc: Fixed issue which does not work with g_serial") Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Link: https://lore.kernel.org/r/20210323153626.54908-3-andriy.shevchenko@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Either way ~0 will be in the correct byte order, hence
replace cpu_to_le32() by lower_32_bits(). Moreover,
it makes sparse happy, otherwise it complains:
.../pch_udc.c:1813:27: warning: incorrect type in assignment (different base types)
.../pch_udc.c:1813:27: expected unsigned int [usertype] dataptr
.../pch_udc.c:1813:27: got restricted __le32 [usertype]
Currently, the late microcode loading mechanism checks whether any CPUs
are offlined, and, in such a case, aborts the load attempt.
However, this must be done before the kernel caches new microcode from
the filesystem. Otherwise, when offlined CPUs are onlined later, those
cores are going to be updated through the CPU hotplug notifier callback
with the new microcode, while CPUs previously onine will continue to run
with the older microcode.
The rationale for why the update is aborted when at least one primary
thread is offline is because even if that thread is soft-offlined
and idle, it will still have to participate in broadcasted MCE's
synchronization dance or enter SMM, and in both examples it will execute
instructions so it better have the same microcode revision as the other
cores.
[ bp: Heavily edit and extend commit message with the reasoning behind all
this. ]
Fixes: 30ec26da9967 ("x86/microcode: Do not upload microcode if CPUs are offline") Signed-off-by: Otavio Pontes <otavio.pontes@intel.com> Signed-off-by: Borislav Petkov <bp@suse.de> Reviewed-by: Tony Luck <tony.luck@intel.com> Acked-by: Ashok Raj <ashok.raj@intel.com> Link: https://lkml.kernel.org/r/20210319165515.9240-2-otavio.pontes@intel.com Signed-off-by: Sasha Levin <sashal@kernel.org>
In qcom_probe_nand_devices() function, the error code returned by
qcom_nand_host_init_and_register() is converted to -ENODEV in the case
of failure. This poses issue if -EPROBE_DEFER is returned when the
dependency is not available for a component like parser.
So let's restructure the error handling logic a bit and return the
actual error code in case of qcom_nand_host_init_and_register() failure.
There are chances that the parse_mtd_partitions() function will return
-EPROBE_DEFER in mtd_device_parse_register(). This might happen when
the dependency is not available for the parser. For instance, on SDX55
the MTD_QCOMSMEM_PARTS parser depends on the QCOM_SMEM driver to parse
the partitions defined in the shared memory region. With the current
flow, the error returned from parse_mtd_partitions() will be discarded
in favor of trying to add the fallback partition.
This will prevent the driver to end up in probe deferred pool and the
partitions won't be parsed even after the QCOM_SMEM driver is available.
Fix this issue by bailing out of mtd_device_parse_register() when
-EPROBE_DEFER error is returned from parse_mtd_partitions() function and
propagate the error code to the driver core for probing later.
Hamming ECC doesn't cover the OOB data, so reading or writing OOB shall
always be done without ECC enabled.
This is a problem when adding JFFS2 cleanmarkers to erased blocks. If JFFS2
clenmarkers are added to the OOB with ECC enabled, OOB bytes will be changed
from ff ff ff to 00 00 00, reporting incorrect ECC errors.
There is a upstream commit cffa4b2122f5("regmap:debugfs:
Fix a memory leak when calling regmap_attach_dev") that
adds a if condition when create name for debugfs_name.
With below function invoking logical, debugfs_name is
freed in regmap_debugfs_exit(), but it is not created again
because of the if condition introduced by above commit.
regmap_reinit_cache()
regmap_debugfs_exit()
...
regmap_debugfs_init()
So, set debugfs_name to NULL after it is freed.
Fixes: cffa4b2122f5 ("regmap: debugfs: Fix a memory leak when calling regmap_attach_dev") Signed-off-by: Meng Li <Meng.Li@windriver.com> Link: https://lore.kernel.org/r/20210226021737.7690-1-Meng.Li@windriver.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
While interpreting CC_STATUS, ROLE_CONTROL has to be read to make
sure that CC1/CC2 is not forced presenting Rp/Rd.
>From the TCPCI spec:
4.4.5.2 ROLE_CONTROL (Normative):
The TCPM shall write B6 (DRP) = 0b and B3..0 (CC1/CC2) if it wishes
to control the Rp/Rd directly instead of having the TCPC perform
DRP toggling autonomously. When controlling Rp/Rd directly, the
TCPM writes to B3..0 (CC1/CC2) each time it wishes to change the
CC1/CC2 values. This control is used for TCPM-TCPC implementing
Source or Sink only as well as when a connection has been detected
via DRP toggling but the TCPM wishes to attempt Try.Src or Try.Snk.
In "tx_empty", we should poll TC bit in both DMA and PIO modes (instead of
TXE) to check transmission data register has been transmitted independently
of the FIFO mode. TC indicates that both transmit register and shift
register are empty. When shift register is empty, tx_empty should return
TIOCSER_TEMT instead of TC value.
Cleans the USART_CR_TC TCCF register define (transmission complete clear
flag) as it is duplicate of USART_ICR_TCCF.
Incorrect characters are observed on console during boot. This issue occurs
when init/main.c is modifying termios settings to open /dev/console on the
rootfs.
This patch adds a waiting loop in set_termios to wait for TX shift register
empty (and TX FIFO if any) before stopping serial port.
projects / thirdparty / kernel / stable.git / log
