Only CS7 and CS8 seem supported but CSIZE is not sanitized to CS8 in
the default: block.
Set CSIZE correctly so that userspace knows the effective value.
Incorrect CSIZE also results in miscalculation of the frame bits in
tty_get_char_size() or in its predecessor where the roughly the same
code is directly within uart_update_timeout().
SER_RS485_RTS_ON_SEND and SER_RS485_RTS_AFTER_SEND relate to behavior
within RS485 operation. The driver checks if they have the same value
which is not possible to realize with the hardware. The check is taken
regardless of SER_RS485_ENABLED flag and -EINVAL is returned when the
check fails, which creates problems.
This check makes it unnecessarily complicated to turn RS485 mode off as
simple zeroed serial_rs485 struct will trigger that equal values check.
In addition, the driver itself memsets its rs485 structure to zero when
RS485 is disabled but if userspace would try to make an TIOCSRS485
ioctl() call with the very same struct, it would end up failing with
-EINVAL which doesn't make much sense.
Resolve the problem by moving the check inside SER_RS485_ENABLED block.
The uart_ops startup() callback is called without interrupts
disabled and without port->lock locked, relatively late during the
boot process (from the call path of console_on_rootfs()). If the
device is a console, it was already previously registered and could
be actively printing messages.
Since the startup() callback is reading/writing registers used by
the console write() callback (AML_UART_CONTROL), its access must
be synchronized using the port->lock. Currently it is not.
The startup() callback is the only function that explicitly enables
interrupts. Without the synchronization, it is possible that
interrupts become accidentally permanently disabled.
Some implementations of the SBI time extension depend on hart-local
state (for example, CSRs) that are lost or hardware that is powered
down when a CPU is suspended. To be safe, the clockevents driver
cannot assume that timer IRQs will be received during CPU suspend.
Fixes: 62b019436814 ("clocksource: new RISC-V SBI timer driver") Signed-off-by: Samuel Holland <samuel@sholland.org> Reviewed-by: Anup Patel <anup@brainfault.org> Link: https://lore.kernel.org/r/20220509012121.40031-1-samuel@sholland.org Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
of_find_matching_node_and_match returns a node pointer with refcount
incremented, we should use of_node_put() on it when done.
Add missing of_node_put() to avoid refcount leak.
Add device managed action to sync pending queue work, otherwise
the queued work may run after the work is destroyed.
Fixes: 4ed754de2d66 ("extcon: Add support for ptn5150 extcon driver") Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Signed-off-by: Li Jun <jun.li@nxp.com> Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The panic notifier infrastructure executes registered callbacks when
a panic event happens - such callbacks are executed in atomic context,
with interrupts and preemption disabled in the running CPU and all other
CPUs disabled. That said, mutexes in such context are not a good idea.
This patch replaces a regular mutex with a mutex_trylock safer approach;
given the nature of the mutex used in the driver, it should be pretty
uncommon being unable to acquire such mutex in the panic path, hence
no functional change should be observed (and if it is, that would be
likely a deadlock with the regular mutex).
Fixes: 2227b7c74634 ("coresight: add support for CPU debug module") Cc: Leo Yan <leo.yan@linaro.org> Cc: Mathieu Poirier <mathieu.poirier@linaro.org> Cc: Mike Leach <mike.leach@linaro.org> Cc: Suzuki K Poulose <suzuki.poulose@arm.com> Signed-off-by: Guilherme G. Piccoli <gpiccoli@igalia.com> Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com> Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com> Link: https://lore.kernel.org/r/20220427224924.592546-10-gpiccoli@igalia.com Signed-off-by: Sasha Levin <sashal@kernel.org>
The base baud value reported is supposed to be the highest baud rate
that can be set for a serial port. The SiFive FU740-C000 SOC's on-chip
UART supports baud rates of up to 1/16 of the input clock rate, which is
the bus clock `tlclk'[1], often at 130MHz in the case of the HiFive
Unmatched board.
However the sifive UART driver reports a fixed value of 115200 instead:
10010000.serial: ttySIF0 at MMIO 0x10010000 (irq = 1, base_baud = 115200) is a SiFive UART v0 10011000.serial: ttySIF1 at MMIO 0x10011000 (irq = 2, base_baud = 115200) is a SiFive UART v0
even though we already support setting higher baud rates, e.g.:
$ tty
/dev/ttySIF1
$ stty speed
230400
The baud base value is computed by the serial core by dividing the UART
clock recorded in `struct uart_port' by 16, which is also the minimum
value of the clock divider supported, so correct the baud base value
reported by setting the UART clock recorded to the input clock rate
rather than 115200:
10010000.serial: ttySIF0 at MMIO 0x10010000 (irq = 1, base_baud = 8125000) is a SiFive UART v0 10011000.serial: ttySIF1 at MMIO 0x10011000 (irq = 2, base_baud = 8125000) is a SiFive UART v0
Small adjustment the scale calibration value for the sc2731,
use new name sc2731_[big|small]_scale_graph_calib, and remove
the origin [big|small]_scale_graph_calib struct for unused.
wait_for_completion_timeout() returns unsigned long not int.
It returns 0 if timed out, and positive if completed.
The check for <= 0 is ambiguous and should be == 0 here
indicating timeout which is the only error case.
wait_for_completion_timeout() returns unsigned long not long.
it returns 0 if timed out, and positive if completed.
The check for <= 0 is ambiguous and should be == 0 here
indicating timeout which is the only error case
Fixes: e813dde6f833 ("iio: stmpe-adc: Use wait_for_completion_timeout") Signed-off-by: Miaoqian Lin <linmq006@gmail.com> Reviewed-by: Philippe Schenker <philippe.schenker@toradex.com> Link: https://lore.kernel.org/r/20220412065150.14486-1-linmq006@gmail.com Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The list iterator 'pmem' will point to a bogus position containing
HEAD if the list is empty or no element is found. This case must
be checked before any use of the iterator, otherwise it will
lead to a invalid memory access.
To fix this bug, just gen_pool_free/set NULL/list_del() and return
when found, otherwise list_del HEAD and return;
The list iterator value 'buf' will *always* be set and non-NULL
by list_for_each_entry(), so it is incorrect to assume that the
iterator value will be NULL if the list is empty (in this case, the
check 'if (!buf) {' will always be false and never exit expectly).
To fix the bug, use a new variable 'iter' as the list iterator,
while use the original variable 'buf' as a dedicated pointer to
point to the found element.
If the device is already in a runtime PM enabled state
pm_runtime_get_sync() will return 1, so a test for negative
value should be used to check for errors.
The hardware only supports periods <= 1.6 ms and if a bigger period is
requested it is clamped to 1.6 ms. In this case duty_cycle might be bigger
than 1.6 ms and then the duty cycle register is written with a value
bigger than LP3943_MAX_DUTY. So clamp duty_cycle accordingly.
If device_register() fails, device_unregister() should not be called
because it will free some resources that are not allocated.
put_device() should be used instead.
The function documentation of usb_set_configuration says that its
callers should hold the device lock. This lock is held for all
callsites except tweak_set_configuration_cmd. The code path can be
executed for example when attaching a remote USB device.
The solution is to surround the call by the device lock.
This bug was found using my experimental own-developed static analysis
tool, which reported the missing lock on v5.17.2. I manually verified
this bug report by doing code review as well. I runtime checked that
the required lock is not held. I compiled and runtime tested this on
x86_64 with a USB mouse. After applying this patch, my analyser no
longer reports this potential bug.
Now fsl_lpuart driver use both of_alias_get_id() and ida_simple_get() in
.probe(), which has the potential bug. For example, when remove the
lpuart7 alias in dts, of_alias_get_id() will return error, then call
ida_simple_get() to allocate the id 0 for lpuart7, this may confilct
with the lpuart4 which has alias 0.
So remove the ida_simple_get() in .probe(), return an error directly
when calling of_alias_get_id() fails, which is consistent with other
uart drivers behavior.
Fixes: 3bc3206e1c0f ("serial: fsl_lpuart: Remove the alias node dependence") Signed-off-by: Sherry Sun <sherry.sun@nxp.com> Link: https://lore.kernel.org/r/20220321112211.8895-1-sherry.sun@nxp.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
TTYs in ICANON mode have a special case that allows "pushing" a line
without a regular EOL character (like newline), by using EOF (the EOT
character - ASCII 0x4) as a pseudo-EOL. It is silently discarded, so
the reader of the PTS will receive the line *without* EOF or any other
terminating character.
This special case has an edge case: What happens if the readers buffer
is the same size as the line (without EOF)? Will they be able to tell
if the whole line is received, i.e. if the next read() will return more
of the same line or the next line?
There are two possibilities, that both have (dis)advantages:
1. The next read() returns 0. FreeBSD (13.0) and OSX (10.11) do this.
Advantage: The reader can interpret this as "the line is over".
Disadvantage: read() returning 0 means EOF, the reader could also
interpret it as "there's no more data" and stop reading or even
close the PT.
2. The next read() returns the next line, the EOF is silently discarded.
Solaris (or at least OpenIndiana 2021.10) does this, Linux has done
do this since commit 40d5e0905a03 ("n_tty: Fix EOF push handling");
this behavior was recently broken by commit 359303076163 ("tty:
n_tty: do not look ahead for EOL character past the end of the buffer").
Advantage: read() won't return 0 (EOF), reader less likely to be
confused (and things like `while(read(..)>0)` don't break)
Disadvantage: The reader can't really know if the read() continues
the last line (that filled the whole read buffer) or starts a
new line.
As both options are defensible (and are used by other Unix-likes), it's
best to stick to the "old" behavior since "n_tty: Fix EOF push handling"
of 2013, i.e. silently discard that EOF.
This patch - that I actually got from Linus for testing and only
modified slightly - restores that behavior by skipping an EOF
character if it's the next character after reading is done.
Based on a patch from Linus Torvalds.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=215611 Fixes: 359303076163 ("tty: n_tty: do not look ahead for EOL character past the end of the buffer") Cc: Peter Hurley <peter@hurleysoftware.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Jiri Slaby <jirislaby@kernel.org> Reviewed-and-tested-by: Daniel Gibson <daniel@gibson.sh> Acked-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Daniel Gibson <daniel@gibson.sh> Link: https://lore.kernel.org/r/20220329235810.452513-2-daniel@gibson.sh Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In goldfish_tty_probe(), the port initialized through tty_port_init()
should be destroyed in error paths.In goldfish_tty_remove(), qtty->port
also should be destroyed or else might leak resources.
As the possible failure of the kmalloc(), the not_checked and checked
could be NULL pointer.
Therefore, it should be better to check it in order to avoid the
dereference of the NULL pointer.
Also, we need to kfree the 'not_checked' and 'checked' to avoid
the memory leak if fails.
And since it is just a test, it may directly return without error
number.
If the list does not exit early then data == NULL and 'module' does not
point to a valid list element.
Using 'module' in such a case is not valid and was therefore removed.
Fixes: 6dd67645f22c ("greybus: audio: Use single codec driver registration") Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by: Vaibhav Agarwal <vaibhav.sr@gmail.com> Reviewed-by: Mark Greer <mgreer@animalcreek.com> Signed-off-by: Jakob Koschel <jakobkoschel@gmail.com> Link: https://lore.kernel.org/r/20220321123626.3068639-1-jakobkoschel@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When the MIPS_ALCHEMY board selection is MIPS_XXS1500 instead of
MIPS_DB1XXX, the PCMCIA driver 'db1xxx_ss' has build errors due
to missing DB1XXX symbols. The PCMCIA driver should be restricted
to MIPS_DB1XXX instead of MIPS_ALCHEMY to fix this build error.
Make the test_dummy_encryption mount option require that the encrypt
feature flag be already enabled on the filesystem, rather than
automatically enabling it. Practically, this means that "-O encrypt"
will need to be included in MKFS_OPTIONS when running xfstests with the
test_dummy_encryption mount option. (ext4/053 also needs an update.)
Moreover, as long as the preconditions for test_dummy_encryption are
being tightened anyway, take the opportunity to start rejecting it when
!CONFIG_FS_ENCRYPTION rather than ignoring it.
The motivation for requiring the encrypt feature flag is that:
- Having the filesystem auto-enable feature flags is problematic, as it
bypasses the usual sanity checks. The specific issue which came up
recently is that in kernel versions where ext4 supports casefold but
not encrypt+casefold (v5.1 through v5.10), the kernel will happily add
the encrypt flag to a filesystem that has the casefold flag, making it
unmountable -- but only for subsequent mounts, not the initial one.
This confused the casefold support detection in xfstests, causing
generic/556 to fail rather than be skipped.
- The xfstests-bld test runners (kvm-xfstests et al.) already use the
required mkfs flag, so they will not be affected by this change. Only
users of test_dummy_encryption alone will be affected. But, this
option has always been for testing only, so it should be fine to
require that the few users of this option update their test scripts.
- f2fs already requires it (for its equivalent feature flag).
Signed-off-by: Eric Biggers <ebiggers@google.com> Reviewed-by: Gabriel Krisman Bertazi <krisman@collabora.com> Link: https://lore.kernel.org/r/20220519204437.61645-1-ebiggers@kernel.org Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove unsupported forcing of `cpu_has_fpu' to 1, which makes the `nofpu'
kernel parameter non-functional, and also causes a link error:
ld: arch/mips/kernel/traps.o: in function `trap_init':
./arch/mips/include/asm/msa.h:(.init.text+0x348): undefined reference to `handle_fpe'
ld: ./arch/mips/include/asm/msa.h:(.init.text+0x354): undefined reference to `handle_fpe'
ld: ./arch/mips/include/asm/msa.h:(.init.text+0x360): undefined reference to `handle_fpe'
where the CONFIG_MIPS_FP_SUPPORT configuration option has been disabled.
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk> Reported-by: Stephen Zhang <starzhangzsd@gmail.com> Fixes: 7505576d1c1a ("MIPS: add support for SGI Octane (IP30)") Cc: stable@vger.kernel.org # v5.5+ Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove unsupported forcing of `cpu_has_fpu' to 1, which makes the `nofpu'
kernel parameter non-functional, and also causes a link error:
ld: arch/mips/kernel/traps.o: in function `trap_init':
./arch/mips/include/asm/msa.h:(.init.text+0x348): undefined reference to `handle_fpe'
ld: ./arch/mips/include/asm/msa.h:(.init.text+0x354): undefined reference to `handle_fpe'
ld: ./arch/mips/include/asm/msa.h:(.init.text+0x360): undefined reference to `handle_fpe'
where the CONFIG_MIPS_FP_SUPPORT configuration option has been disabled.
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk> Reported-by: Stephen Zhang <starzhangzsd@gmail.com> Fixes: 0ebb2f4159af ("MIPS: IP27: Update/restructure CPU overrides") Cc: stable@vger.kernel.org # v4.2+ Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Current rxe_requester() doesn't generate a completion when processing an
unsupported/invalid opcode. If rxe driver doesn't support a new opcode
(e.g. RDMA Atomic Write) and RDMA library supports it, an application
using the new opcode can reproduce this issue. Fix the issue by calling
"goto err;".
Commit d92c370a16cb ("block: really clone the block cgroup in
bio_clone_blkg_association") changed bio_clone_blkg_association() to
just clone bio->bi_blkg reference from source to destination bio. This
is however wrong if the source and destination bios are against
different block devices because struct blkcg_gq is different for each
bdev-blkcg pair. This will result in IOs being accounted (and throttled
as a result) multiple times against the same device (src bdev) while
throttling of the other device (dst bdev) is ignored. In case of BFQ the
inconsistency can even result in crashes in bfq_bic_update_cgroup().
Fix the problem by looking up correct blkcg_gq for the cloned bio.
Reported-by: Logan Gunthorpe <logang@deltatee.com> Reported-and-tested-by: Donald Buczek <buczek@molgen.mpg.de> Fixes: d92c370a16cb ("block: really clone the block cgroup in bio_clone_blkg_association") CC: stable@vger.kernel.org Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Jan Kara <jack@suse.cz> Link: https://lore.kernel.org/r/20220602081242.7731-1-jack@suse.cz Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Bios queued into BFQ IO scheduler can be associated with a cgroup that
was already offlined. This may then cause insertion of this bfq_group
into a service tree. But this bfq_group will get freed as soon as last
bio associated with it is completed leading to use after free issues for
service tree users. Fix the problem by making sure we always operate on
online bfq_group. If the bfq_group associated with the bio is not
online, we pick the first online parent.
CC: stable@vger.kernel.org Fixes: e21b7a0b9887 ("block, bfq: add full hierarchical scheduling and cgroups support") Tested-by: "yukuai (C)" <yukuai3@huawei.com> Signed-off-by: Jan Kara <jack@suse.cz> Reviewed-by: Christoph Hellwig <hch@lst.de> Link: https://lore.kernel.org/r/20220401102752.8599-9-jack@suse.cz Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
BFQ usage of __bio_blkcg() is a relict from the past. Furthermore if bio
would not be associated with any blkcg, the usage of __bio_blkcg() in
BFQ is prone to races with the task being migrated between cgroups as
__bio_blkcg() calls at different places could return different blkcgs.
Convert BFQ to the new situation where bio->bi_blkg is initialized in
bio_set_dev() and thus practically always valid. This allows us to save
blkcg_gq lookup and noticeably simplify the code.
CC: stable@vger.kernel.org Fixes: 0fe061b9f03c ("blkcg: fix ref count issue with bio_blkcg() using task_css") Tested-by: "yukuai (C)" <yukuai3@huawei.com> Signed-off-by: Jan Kara <jack@suse.cz> Reviewed-by: Christoph Hellwig <hch@lst.de> Link: https://lore.kernel.org/r/20220401102752.8599-8-jack@suse.cz Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We call bfq_init_rq() from request merging functions where requests we
get should have already gone through bfq_init_rq() during insert and
anyway we want to do anything only if the request is already tracked by
BFQ. So replace calls to bfq_init_rq() with RQ_BFQQ() instead to simply
skip requests untracked by BFQ. We move bfq_init_rq() call in
bfq_insert_request() a bit earlier to cover request merging and thus
can transfer FIFO position in case of a merge.
CC: stable@vger.kernel.org Tested-by: "yukuai (C)" <yukuai3@huawei.com> Signed-off-by: Jan Kara <jack@suse.cz> Reviewed-by: Christoph Hellwig <hch@lst.de> Link: https://lore.kernel.org/r/20220401102752.8599-6-jack@suse.cz Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In bfq_insert_request() we unlock bfqd->lock only to call
trace_block_rq_insert() and then lock bfqd->lock again. This is really
pointless since tracing is disabled if we really care about performance
and even if the tracepoint is enabled, it is a quick call.
CC: stable@vger.kernel.org Tested-by: "yukuai (C)" <yukuai3@huawei.com> Signed-off-by: Jan Kara <jack@suse.cz> Reviewed-by: Christoph Hellwig <hch@lst.de> Link: https://lore.kernel.org/r/20220401102752.8599-5-jack@suse.cz Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It can happen that the parent of a bfqq changes between the moment we
decide two queues are worth to merge (and set bic->stable_merge_bfqq)
and the moment bfq_setup_merge() is called. This can happen e.g. because
the process submitted IO for a different cgroup and thus bfqq got
reparented. It can even happen that the bfqq we are merging with has
parent cgroup that is already offline and going to be destroyed in which
case the merge can lead to use-after-free issues such as:
BUG: KASAN: use-after-free in __bfq_deactivate_entity+0x9cb/0xa50
Read of size 8 at addr ffff88800693c0c0 by task runc:[2:INIT]/10544
smatch warnings:
drivers/thermal/thermal_core.c:1020 __thermal_cooling_device_register() warn: possible memory leak of 'cdev'
by freeing the cdev when exiting the function in the error path.
Fixes: 584837618100 ("thermal/drivers/core: Use a char pointer for the cooling device name") Reported-by: kernel test robot <lkp@intel.com> Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org> Link: https://lore.kernel.org/r/20210319202257.890848-1-daniel.lezcano@linaro.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When device_register() return failed, program will goto out_kfree_type
to release 'cdev->device' by put_device(). That will call thermal_release()
to free 'cdev'. But the follow-up processes access 'cdev' continually.
That trggers the UAF bug.
Do not use 'cdev' again after put_device() to fix the problem like doing
in thermal_zone_device_register().
[dlezcano]: as requested by Rafael, change the affectation into two statements.
Fixes: 584837618100 ("thermal/drivers/core: Use a char pointer for the cooling device name") Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com> Reported-by: kernel test robot <lkp@intel.com> Link: https://lore.kernel.org/r/20211015024504.947520-1-william.xuanziyang@huawei.com Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 54de76c01239 ("kselftest/cgroup: fix test_stress.sh to use OUTPUT
dir") changes the test_core command path from . to $OUTPUT. However,
variable OUTPUT may not be defined if the command is run interactively.
Fix that by using ${OUTPUT:-.} to cover both cases.
The problem was that an allocation failed unexpectedly in
xfs_bmbt_alloc_block() after roughly 150,000 minlen allocation error
injections, resulting in an EFSCORRUPTED error being returned to
xfs_bmapi_write(). The error occurred on extent-to-btree format
conversion allocating the new root block:
Why the allocation failed at this point is unknown, but is likely
that we ran the transaction out of reserved space and filesystem out
of space with bmbt blocks because of all the minlen allocations
being done causing worst case fragmentation of a large allocation.
Regardless of the cause, we've then called xfs_bmapi_finish() which
calls xfs_btree_del_cursor(cur, error) to tear down the cursor.
So we have a failed operation, error != 0, cur->bc_ino.allocated > 0
and the filesystem is still up. The assert fails to take into
account that allocation can fail with an error and the transaction
teardown will shut the filesystem down if necessary. i.e. the
assert needs to check "|| error != 0" as well, because at this point
shutdown is pending because the current transaction is dirty....
Signed-off-by: Dave Chinner <dchinner@redhat.com> Reviewed-by: Darrick J. Wong <djwong@kernel.org> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Dave Chinner <david@fromorbit.com> Signed-off-by: Amir Goldstein <amir73il@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The assert in xfs_btree_del_cursor() checks that the bmapbt block
allocation field has been handled correctly before the cursor is
freed. This field is used for accurate calculation of indirect block
reservation requirements (for delayed allocations), for example.
generic/019 reproduces a scenario where this assert fails because
the filesystem has shutdown while in the middle of a bmbt record
insertion. This occurs after a bmbt block has been allocated via the
cursor but before the higher level bmap function (i.e.
xfs_bmap_add_extent_hole_real()) completes and resets the field.
Update the assert to accommodate the transient state if the
filesystem has shutdown. While here, clean up the indentation and
comments in the function.
Signed-off-by: Brian Foster <bfoster@redhat.com> Reviewed-by: Darrick J. Wong <djwong@kernel.org> Signed-off-by: Darrick J. Wong <djwong@kernel.org> Signed-off-by: Amir Goldstein <amir73il@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If we allocate quota inodes in the process of mounting a filesystem but
then decide to abort the mount, it's possible that the quota inodes are
sitting around pinned by the log. Now that inode reclaim relies on the
AIL to flush inodes, we have to force the log and push the AIL in
between releasing the quota inodes and kicking off reclaim to tear down
all the incore inodes. Do this by extracting the bits we need from the
unmount path and reusing them. As an added bonus, failed writes during
a failed mount will not retry forever now.
This was originally found during a fuzz test of metadata directories
(xfs/1546), but the actual symptom was that reclaim hung up on the quota
inodes.
Signed-off-by: Darrick J. Wong <djwong@kernel.org> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Dave Chinner <dchinner@redhat.com> Signed-off-by: Amir Goldstein <amir73il@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
XFS triggers an iomap warning in the write fault path due to a
!PageUptodate() page if a write fault happens to occur on a page
that recently failed writeback. The iomap writeback error handling
code can clear the Uptodate flag if no portion of the page is
submitted for I/O. This is reproduced by fstest generic/019, which
combines various forms of I/O with simulated disk failures that
inevitably lead to filesystem shutdown (which then unconditionally
fails page writeback).
This is a regression introduced by commit f150b4234397 ("xfs: split
the iomap ops for buffered vs direct writes") due to the removal of
a shutdown check and explicit error return in the ->iomap_begin()
path used by the write fault path. The explicit error return
historically translated to a SIGBUS, but now carries on with iomap
processing where it complains about the unexpected state. Restore
the shutdown check to xfs_buffered_write_iomap_begin() to restore
historical behavior.
Fixes: f150b4234397 ("xfs: split the iomap ops for buffered vs direct writes") Signed-off-by: Brian Foster <bfoster@redhat.com> Reviewed-by: Eric Sandeen <sandeen@redhat.com> Reviewed-by: Darrick J. Wong <djwong@kernel.org> Signed-off-by: Darrick J. Wong <djwong@kernel.org> Signed-off-by: Amir Goldstein <amir73il@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While writing up a regression test for broken behavior when a chprojid
request fails, I noticed that we were logging corruption notices about
the root dquot of the group/project quota file at mount time when
testing V4 filesystems.
In commit afeda6000b0c, I was trying to improve ondisk dquot validation
by making sure that when we load an ondisk dquot into memory on behalf
of an incore dquot, the dquot id and type matches. Unfortunately, I
forgot that V4 filesystems only have two quota files, and can switch
that file between group and project quota types at mount time. When we
perform that switch, we'll try to load the default quota limits from the
root dquot prior to running quotacheck and log a corruption error when
the types don't match.
This is inconsequential because quotacheck will reset the second quota
file as part of doing the switch, but we shouldn't leave scary messages
in the kernel log.
Fixes: afeda6000b0c ("xfs: validate ondisk/incore dquot flags") Signed-off-by: Darrick J. Wong <djwong@kernel.org> Reviewed-by: Brian Foster <bfoster@redhat.com> Reviewed-by: Chandan Babu R <chandanrlinux@gmail.com> Signed-off-by: Amir Goldstein <amir73il@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While refactoring the quota code to create a function to allocate inode
change transactions, I noticed that xfs_qm_vop_chown_reserve does more
than just make reservations: it also *modifies* the incore counts
directly to handle the owner id change for the delalloc blocks.
I then observed that the fssetxattr code continues validating input
arguments after making the quota reservation but before dirtying the
transaction. If the routine decides to error out, it fails to undo the
accounting switch! This leads to incorrect quota reservation and
failure down the line.
We can fix this by making the reservation function do only that -- for
the new dquot, it reserves ondisk and delalloc blocks to the
transaction, and the old dquot hangs on to its incore reservation for
now. Once we actually switch the dquots, we can then update the incore
reservations because we've dirtied the transaction and it's too late to
turn back now.
No fixes tag because this has been broken since the start of git.
Signed-off-by: Darrick J. Wong <djwong@kernel.org> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Brian Foster <bfoster@redhat.com> Signed-off-by: Amir Goldstein <amir73il@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xfs_log_sbcount() syncs the superblock specifically to accumulate
the in-core percpu superblock counters and commit them to disk. This
is required to maintain filesystem consistency across quiesce
(freeze, read-only mount/remount) or unmount when lazy superblock
accounting is enabled because individual transactions do not update
the superblock directly.
This mechanism works as expected for writable mounts, but
xfs_log_sbcount() skips the update for read-only mounts. Read-only
mounts otherwise still allow log recovery and write out an unmount
record during log quiesce. If a read-only mount performs log
recovery, it can modify the in-core superblock counters and write an
unmount record when the filesystem unmounts without ever syncing the
in-core counters. This leaves the filesystem with a clean log but in
an inconsistent state with regard to lazy sb counters.
Update xfs_log_sbcount() to use the same logic
xfs_log_unmount_write() uses to determine when to write an unmount
record. This ensures that lazy accounting is always synced before
the log is cleaned. Refactor this logic into a new helper to
distinguish between a writable filesystem and a writable log.
Specifically, the log is writable unless the filesystem is mounted
with the norecovery mount option, the underlying log device is
read-only, or the filesystem is shutdown. Drop the freeze state
check because the update is already allowed during the freezing
process and no context calls this function on an already frozen fs.
Also, retain the shutdown check in xfs_log_unmount_write() to catch
the case where the preceding log force might have triggered a
shutdown.
Signed-off-by: Brian Foster <bfoster@redhat.com> Reviewed-by: Gao Xiang <hsiangkao@redhat.com> Reviewed-by: Allison Henderson <allison.henderson@oracle.com> Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com> Reviewed-by: Bill O'Donnell <billodo@redhat.com> Reviewed-by: Darrick J. Wong <djwong@kernel.org> Signed-off-by: Darrick J. Wong <djwong@kernel.org> Signed-off-by: Amir Goldstein <amir73il@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When XFS creates a new symlink, it writes its size to disk but not to the
VFS inode. This causes i_size_read() to return 0 for that symlink until
it is re-read from disk, for example when the system is rebooted.
I found this inconsistency while protecting directories with eCryptFS.
The command "stat path/to/symlink/in/ecryptfs" will report "Size: 0" if
the symlink was created after the last reboot on an XFS root.
Call i_size_write() in xfs_symlink()
Signed-off-by: Jeffrey Mitchell <jeffrey.mitchell@starlab.io> Reviewed-by: Darrick J. Wong <djwong@kernel.org> Signed-off-by: Darrick J. Wong <djwong@kernel.org> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Brian Foster <bfoster@redhat.com> Signed-off-by: Amir Goldstein <amir73il@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the (possibly compound) pages used for receive buffers are
freed using __free_pages(). But according to this comment above the
definition of that function, that's wrong:
If you want to use the page's reference count to decide
when to free the allocation, you should allocate a compound
page, and use put_page() instead of __free_pages().
Convert the call to __free_pages() in ipa_endpoint_replenish_one()
to use put_page() instead.
Fixes: 6a606b90153b8 ("net: ipa: allocate transaction in replenish loop") Signed-off-by: Alex Elder <elder@linaro.org> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the (possibly compound) page used for receive buffers are
freed using __free_pages(). But according to this comment above the
definition of that function, that's wrong:
If you want to use the page's reference count to decide when
to free the allocation, you should allocate a compound page,
and use put_page() instead of __free_pages().
Convert the call to __free_pages() in ipa_endpoint_trans_release()
to use put_page() instead.
It is possibe that probe failure issue happens when the device
and its child_device's probe happens at the same time.
In coresight_make_links, has_conns_grp is true for parent, but
has_conns_grp is false for child device as has_conns_grp is set
to true in coresight_create_conns_sysfs_group. The probe of parent
device will fail at this condition. Add has_conns_grp check for
child device before make the links and make the process from
device_register to connection_create be atomic to avoid this
probe failure issue.
Cc: stable@vger.kernel.org Suggested-by: Suzuki K Poulose <suzuki.poulose@arm.com> Suggested-by: Mike Leach <mike.leach@linaro.org> Signed-off-by: Mao Jinlong <quic_jinlmao@quicinc.com> Link: https://lore.kernel.org/r/20220309142206.15632-1-quic_jinlmao@quicinc.com
[ Added Cc stable ] Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
iolatency needs to track the number of inflight IOs per cgroup. As this
tracking can be expensive, it is disabled when no cgroup has iolatency
configured for the device. To ensure that the inflight counters stay
balanced, iolatency_set_limit() freezes the request_queue while manipulating
the enabled counter, which ensures that no IO is in flight and thus all
counters are zero.
Unfortunately, iolatency_set_limit() isn't the only place where the enabled
counter is manipulated. iolatency_pd_offline() can also dec the counter and
trigger disabling. As this disabling happens without freezing the q, this
can easily happen while some IOs are in flight and thus leak the counts.
This can be easily demonstrated by turning on iolatency on an one empty
cgroup while IOs are in flight in other cgroups and then removing the
cgroup. Note that iolatency shouldn't have been enabled elsewhere in the
system to ensure that removing the cgroup disables iolatency for the whole
device.
The following keeps flipping on and off iolatency on sda:
If a cgroup with stuck inflight ends up getting throttled, the throttled IOs
will never get issued as there's no completion event to wake it up leading
to an indefinite hang.
This patch fixes the bug by unifying enable handling into a work item which
is automatically kicked off from iolatency_set_min_lat_nsec() which is
called from both iolatency_set_limit() and iolatency_pd_offline() paths.
Punting to a work item is necessary as iolatency_pd_offline() is called
under spinlocks while freezing a request_queue requires a sleepable context.
This also simplifies the code reducing LOC sans the comments and avoids the
unnecessary freezes which were happening whenever a cgroup's latency target
is newly set or cleared.
Signed-off-by: Tejun Heo <tj@kernel.org> Cc: Josef Bacik <josef@toxicpanda.com> Cc: Liu Bo <bo.liu@linux.alibaba.com> Fixes: 8c772a9bfc7c ("blk-iolatency: fix IO hang due to negative inflight counter") Cc: stable@vger.kernel.org # v5.0+ Link: https://lore.kernel.org/r/Yn9ScX6Nx2qIiQQi@slm.duckdns.org Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
if (cfile) {
cifsFileInfo_put(cfile); // sends SMB2_CLOSE to the server
cfile = NULL;
This is triggered by smb2_query_path_info operation that happens during
revalidate_dentry. In smb2_query_path_info, get_readable_path is called to
load the cfile, increasing the reference counter. If in the meantime, this
reference becomes the very last, this call to cifsFileInfo_put(cfile) will
trigger a SMB2_CLOSE request sent to the server just before sending this compound
request – and so then the compound request fails either with EBADF/EIO depending
on the timing at the server, because the handle is already closed.
In the first scenario, the race seems to be happening between smb2_query_path_info
triggered by the rename operation, and between “cleanup” of asynchronous writes – while
fsync(fd) likely waits for the asynchronous writes to complete, releasing the writeback
structures can happen after the close(fd) call. So the EBADF/EIO errors will pop up if
the timing is such that:
1) There are still outstanding references after close(fd) in the writeback structures
2) smb2_query_path_info successfully fetches the cfile, increasing the refcounter by 1
3) All writeback structures release the same cfile, reducing refcounter to 1
4) smb2_compound_op is called with that cfile
In the second scenario, the race seems to be similar – here open triggers the
smb2_query_path_info operation, and if all other threads in the meantime decrease the
refcounter to 1 similarly to the first scenario, again SMB2_CLOSE will be sent to the
server just before issuing the compound request. This case is harder to reproduce.
See https://bugzilla.samba.org/show_bug.cgi?id=15051
Cc: stable@vger.kernel.org Fixes: 8de9e86c67ba ("cifs: create a helper to find a writeable handle by path name") Signed-off-by: Ondrej Hubsch <ohubsch@purestorage.com> Reviewed-by: Ronnie Sahlberg <lsahlber@redhat.com> Reviewed-by: Paulo Alcantara (SUSE) <pc@cjr.nz> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 766c6b63aa04 ("spi: fix client driver breakages when using
GPIO descriptors"), the panel has been blank due to an inverted CS GPIO.
In order to correct this, drop the spi-cs-high from the panel SPI device.
The list iterator value 'crtc' will *always* be set and non-NULL by
list_for_each_entry(), so it is incorrect to assume that the iterator
value will be NULL if the list is empty or no element is found.
To fix the bug, return 'crtc' when found, otherwise return NULL.
The list iterator value 'encoder' will *always* be set and non-NULL
by list_for_each_entry(), so it is incorrect to assume that the
iterator value will be NULL if the list is empty or no element
is found.
To fix the bug, use a new variable 'iter' as the list iterator,
while use the original variable 'encoder' as a dedicated pointer
to point to the found element.
When x_char is to be sent, the TX path overwrites whatever is in the
circular buffer at offset 0 with x_char and sends it using
pch_uart_hal_write(). I don't understand how this was supposed to work
if xmit->buf[0] already contained some character. It must have been
lost.
Remove this whole pop_tx_x() concept and do the work directly in the
callers. (Without printing anything using dev_dbg().)
The journal no-space deadlock was reported time to time. Such deadlock
can happen in the following situation.
When all journal buckets are fully filled by active jset with heavy
write I/O load, the cache set registration (after a reboot) will load
all active jsets and inserting them into the btree again (which is
called journal replay). If a journaled bkey is inserted into a btree
node and results btree node split, new journal request might be
triggered. For example, the btree grows one more level after the node
split, then the root node record in cache device super block will be
upgrade by bch_journal_meta() from bch_btree_set_root(). But there is no
space in journal buckets, the journal replay has to wait for new journal
bucket to be reclaimed after at least one journal bucket replayed. This
is one example that how the journal no-space deadlock happens.
The solution to avoid the deadlock is to reserve 1 journal bucket in
run time, and only permit the reserved journal bucket to be used during
cache set registration procedure for things like journal replay. Then
the journal space will never be fully filled, there is no chance for
journal no-space deadlock to happen anymore.
This patch adds a new member "bool do_reserve" in struct journal, it is
inititalized to 0 (false) when struct journal is allocated, and set to
1 (true) by bch_journal_space_reserve() when all initialization done in
run_cache_set(). In the run time when journal_reclaim() tries to
allocate a new journal bucket, free_journal_buckets() is called to check
whether there are enough free journal buckets to use. If there is only
1 free journal bucket and journal->do_reserve is 1 (true), the last
bucket is reserved and free_journal_buckets() will return 0 to indicate
no free journal bucket. Then journal_reclaim() will give up, and try
next time to see whetheer there is free journal bucket to allocate. By
this method, there is always 1 jouranl bucket reserved in run time.
During the cache set registration, journal->do_reserve is 0 (false), so
the reserved journal bucket can be used to avoid the no-space deadlock.
After making bch_sectors_dirty_init() being multithreaded, the existing
incremental dirty sector counting in bch_root_node_dirty_init() doesn't
release btree occupation after iterating 500000 (INIT_KEYS_EACH_TIME)
bkeys. Because a read lock is added on btree root node to prevent the
btree to be split during the dirty sectors counting, other I/O requester
has no chance to gain the write lock even restart bcache_btree().
That is to say, the incremental dirty sectors counting is incompatible
to the multhreaded bch_sectors_dirty_init(). We have to choose one and
drop another one.
In my testing, with 512 bytes random writes, I generate 1.2T dirty data
and a btree with 400K nodes. With single thread and incremental dirty
sectors counting, it takes 30+ minites to register the backing device.
And with multithreaded dirty sectors counting, the backing device
registration can be accomplished within 2 minutes.
The 30+ minutes V.S. 2- minutes difference makes me decide to keep
multithreaded bch_sectors_dirty_init() and drop the incremental dirty
sectors counting. This is what this patch does.
But INIT_KEYS_EACH_TIME is kept, in sectors_dirty_init_fn() the CPU
will be released by cond_resched() after every INIT_KEYS_EACH_TIME keys
iterated. This is to avoid the watchdog reports a bogus soft lockup
warning.
Fixes: b144e45fc576 ("bcache: make bch_sectors_dirty_init() to be multithreaded") Signed-off-by: Coly Li <colyli@suse.de> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20220524102336.10684-4-colyli@suse.de Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit b144e45fc576 ("bcache: make bch_sectors_dirty_init() to be
multithreaded") makes bch_sectors_dirty_init() to be much faster
when counting dirty sectors by iterating all dirty keys in the btree.
But it isn't in ideal shape yet, still can be improved.
This patch does the following changes to improve current parallel dirty
keys iteration on the btree,
- Add read lock to root node when multiple threads iterating the btree,
to prevent the root node gets split by I/Os from other registered
bcache devices.
- Remove local variable "char name[32]" and generate kernel thread name
string directly when calling kthread_run().
- Allocate "struct bch_dirty_init_state state" directly on stack and
avoid the unnecessary dynamic memory allocation for it.
- Decrease BCH_DIRTY_INIT_THRD_MAX from 64 to 12 which is enough indeed.
- Increase &state->started to count created kernel thread after it
succeeds to create.
- When wait for all dirty key counting threads to finish, use
wait_event() to replace wait_event_interruptible().
With the above changes, the code is more clear, and some potential error
conditions are avoided.
Fixes: b144e45fc576 ("bcache: make bch_sectors_dirty_init() to be multithreaded") Signed-off-by: Coly Li <colyli@suse.de> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20220524102336.10684-3-colyli@suse.de Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 8e7102273f59 ("bcache: make bch_btree_check() to be
multithreaded") makes bch_btree_check() to be much faster when checking
all btree nodes during cache device registration. But it isn't in ideal
shap yet, still can be improved.
This patch does the following thing to improve current parallel btree
nodes check by multiple threads in bch_btree_check(),
- Add read lock to root node while checking all the btree nodes with
multiple threads. Although currently it is not mandatory but it is
good to have a read lock in code logic.
- Remove local variable 'char name[32]', and generate kernel thread name
string directly when calling kthread_run().
- Allocate local variable "struct btree_check_state check_state" on the
stack and avoid unnecessary dynamic memory allocation for it.
- Reduce BCH_BTR_CHKTHREAD_MAX from 64 to 12 which is enough indeed.
- Increase check_state->started to count created kernel thread after it
succeeds to create.
- When wait for all checking kernel threads to finish, use wait_event()
to replace wait_event_interruptible().
With this change, the code is more clear, and some potential error
conditions are avoided.
Fixes: 8e7102273f59 ("bcache: make bch_btree_check() to be multithreaded") Signed-off-by: Coly Li <colyli@suse.de> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20220524102336.10684-2-colyli@suse.de Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The two bugs are here:
if (encoder) {
if (bridge && bridge->timings)
The list iterator value 'encoder/bridge' will *always* be set and
non-NULL by drm_for_each_encoder()/list_for_each_entry(), so it is
incorrect to assume that the iterator value will be NULL if the
list is empty or no element is found.
To fix the bug, use a new variable '*_iter' as the list iterator,
while use the old variable 'encoder/bridge' as a dedicated pointer
to point to the found element.
If the previous list_for_each_entry_continue_rcu() don't exit early
(no goto hit inside the loop), the iterator 'cvif' after the loop
will be a bogus pointer to an invalid structure object containing
the HEAD (&ar->vif_list). As a result, the use of 'cvif' after that
will lead to a invalid memory access (i.e., 'cvif->id': the invalid
pointer dereference when return back to/after the callsite in the
carl9170_update_beacon()).
The original intention should have been to return the valid 'cvif'
when found in list, NULL otherwise. So just return NULL when no
entry found, to fix this bug.
Cc: stable@vger.kernel.org Fixes: 1f1d9654e183c ("carl9170: refactor carl9170_update_beacon") Signed-off-by: Xiaomeng Tong <xiam0nd.tong@gmail.com> Acked-by: Christian Lamparter <chunkeey@gmail.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20220328122820.1004-1-xiam0nd.tong@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver has a custom put function for "DSP Voice Wake Up" which does
not generate event notifications on change, instead returning 0. Since we
already exit early in the case that there is no change this can be fixed
by unconditionally returning 1 at the end of the function.
Using not existing queues can panic the kernel with rtl8180/rtl8185 cards.
Ignore the skb priority for those cards, they only have one tx queue. Pierre
Asselin (pa@panix.com) reported the kernel crash in the Gentoo forum:
He also confirmed that this patch fixes the issue. In summary this happened:
After updating wpa_supplicant from 2.9 to 2.10 the kernel crashed with a
"divide error: 0000" when connecting to an AP. Control port tx now tries to
use IEEE80211_AC_VO for the priority, which wpa_supplicants starts to use in
2.10.
Since only the rtl8187se part of the driver supports QoS, the priority
of the skb is set to IEEE80211_AC_BE (2) by mac80211 for rtl8180/rtl8185
cards.
rtl8180 is then unconditionally reading out the priority and finally crashes on
drivers/net/wireless/realtek/rtl818x/rtl8180/dev.c line 544 without this
patch:
idx = (ring->idx + skb_queue_len(&ring->queue)) % ring->entries
"ring->entries" is zero for rtl8180/rtl8185 cards, tx_ring[2] never got
initialized.
Cc: stable@vger.kernel.org Reported-by: pa@panix.com Tested-by: pa@panix.com Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20220422145228.7567-1-alexander@wetzel-home.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit a69755b18774 ("xtensa simdisk: switch to proc_create_data()")
split read operation into two parts, first retrieving the path when it's
non-null and second retrieving the trailing '\n'. However when the path
is non-null the first simple_read_from_buffer updates ppos, and the
second simple_read_from_buffer returns 0 if ppos is greater than 1 (i.e.
almost always). As a result reading from that proc file is almost always
empty.
Fix it by making a temporary copy of the path with the trailing '\n' and
using simple_read_from_buffer on that copy.
Cc: stable@vger.kernel.org Fixes: a69755b18774 ("xtensa simdisk: switch to proc_create_data()") Signed-off-by: Yi Yang <yiyang13@huawei.com> Signed-off-by: Max Filippov <jcmvbkbc@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The routine huge_pmd_unshare() is passed a pointer to an address
associated with an area which may be unshared. If unshare is successful
this address is updated to 'optimize' callers iterating over huge page
addresses. For the optimization to work correctly, address should be
updated to the last huge page in the unmapped/unshared area. However, in
the common case where the passed address is PUD_SIZE aligned, the address
is incorrectly updated to the address of the preceding huge page. That
wastes CPU cycles as the unmapped/unshared range is scanned twice.
Link: https://lkml.kernel.org/r/20220524205003.126184-1-mike.kravetz@oracle.com Fixes: 39dde65c9940 ("shared page table for hugetlb page") Signed-off-by: Mike Kravetz <mike.kravetz@oracle.com> Acked-by: Muchun Song <songmuchun@bytedance.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With gcc version 12.0.1 20220401 (Red Hat 12.0.1-0), building with
defconfig results in the following compilation error:
| CC mm/swapfile.o
| mm/swapfile.c: In function `setup_swap_info':
| mm/swapfile.c:2291:47: error: array subscript -1 is below array bounds
| of `struct plist_node[]' [-Werror=array-bounds]
| 2291 | p->avail_lists[i].prio = 1;
| | ~~~~~~~~~~~~~~^~~
| In file included from mm/swapfile.c:16:
| ./include/linux/swap.h:292:27: note: while referencing `avail_lists'
| 292 | struct plist_node avail_lists[]; /*
| | ^~~~~~~~~~~
This is due to the compiler detecting that the mask in
node_states[__state] could theoretically be zero, which would lead to
first_node() returning -1 through find_first_bit.
I believe that the warning/error is legitimate. I first tried adding a
test to check that the node mask is not emtpy, since a similar test exists
in the case where MAX_NUMNODES == 1.
However, adding the if statement causes other warnings to appear in
for_each_cpu_node_but, because it introduces a dangling else ambiguity.
And unfortunately, GCC is not smart enough to detect that the added test
makes the case where (node) == -1 impossible, so it still complains with
the same message.
This is why I settled on replacing that with a harmless, but relatively
useless (node) >= 0 test. Based on the warning for the dangling else, I
also decided to fix the case where MAX_NUMNODES == 1 by moving the
condition inside the for loop. It will still only be tested once. This
ensures that the meaning of an else following for_each_node_mask or
derivatives would not silently have a different meaning depending on the
configuration.
Link: https://lkml.kernel.org/r/20220414150855.2407137-3-dinechin@redhat.com Signed-off-by: Christophe de Dinechin <christophe@dinechin.org> Signed-off-by: Christophe de Dinechin <dinechin@redhat.com> Reviewed-by: Andrew Morton <akpm@linux-foundation.org> Cc: Ben Segall <bsegall@google.com> Cc: "Michael S. Tsirkin" <mst@redhat.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Ingo Molnar <mingo@redhat.com> Cc: Mel Gorman <mgorman@suse.de> Cc: Dietmar Eggemann <dietmar.eggemann@arm.com> Cc: Vincent Guittot <vincent.guittot@linaro.org> Cc: Paolo Bonzini <pbonzini@redhat.com> Cc: Daniel Bristot de Oliveira <bristot@redhat.com> Cc: Jason Wang <jasowang@redhat.com> Cc: Zhen Lei <thunder.leizhen@huawei.com> Cc: Juri Lelli <juri.lelli@redhat.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The bug is here:
if (!iommu || iommu->dev->of_node != spec->np) {
The list iterator value 'iommu' will *always* be set and non-NULL by
list_for_each_entry(), so it is incorrect to assume that the iterator
value will be NULL if the list is empty or no element is found (in fact,
it will point to a invalid structure object containing HEAD).
To fix the bug, use a new value 'iter' as the list iterator, while use
the old value 'iommu' as a dedicated variable to point to the found one,
and remove the unneeded check for 'iommu->dev->of_node != spec->np'
outside the loop.
One way to trigger this is:
1. load a livepatch that patches kernel function xxx;
2. run bpftrace -e 'kfunc:xxx {}', this will fail (expected for now);
3. repeat #2 => gpf.
This is because the entry is added to direct_functions, but not removed.
Fix this by remove the entry from direct_functions when
register_ftrace_direct fails.
Also remove the last trailing space from ftrace.c, so we don't have to
worry about it anymore.
Link: https://lkml.kernel.org/r/20220524170839.900849-1-song@kernel.org Cc: stable@vger.kernel.org Fixes: 763e34e74bb7 ("ftrace: Add register_ftrace_direct()") Signed-off-by: Song Liu <song@kernel.org> Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit d1bcae833b32f1 ("ELF: Don't generate unused section
symbols") [1], binutils (v2.36+) started dropping section symbols that
it thought were unused. This isn't an issue in general, but with
kexec_file.c, gcc is placing kexec_arch_apply_relocations[_add] into a
separate .text.unlikely section and the section symbol ".text.unlikely"
is being dropped. Due to this, recordmcount is unable to find a non-weak
symbol in .text.unlikely to generate a relocation record against.
Address this by dropping the weak attribute from these functions.
Instead, follow the existing pattern of having architectures #define the
name of the function they want to override in their headers.
syscall_stub_data() expects the data_count parameter to be the number of
longs, not bytes.
==================================================================
BUG: KASAN: stack-out-of-bounds in syscall_stub_data+0x70/0xe0
Read of size 128 at addr 000000006411f6f0 by task swapper/1
The previous fix here was only partially correct, it did
result in returning a proper error value in case of error,
but it also clobbered the pid that we need to return from
this function (not just zero for success).
As a result, it returned 0 here, but later this is treated
as a pid and used to kill the process, but since it's now
0 we kill(0, SIGKILL), which makes UML kill itself rather
than just the helper thread.
Fix that and make it more obvious by using a separate
variable for the pid.
Fixes: ccf1236ecac4 ("um: fix error return code in winch_tramp()") Reported-and-tested-by: Nathan Chancellor <nathan@kernel.org> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Cc: stable@vger.kernel.org Signed-off-by: Richard Weinberger <richard@nod.at> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In client mode, we can't connect to hidden SSID APs or SSIDs not advertised
in beacons on DFS channels, since we're forced to passive scan. Fix this by
sending out a probe request immediately after the first beacon, if active
scan was requested by the user.
Cc: stable@vger.kernel.org Reported-by: Catrinel Catrinescu <cc@80211.de> Signed-off-by: Felix Fietkau <nbd@nbd.name> Link: https://lore.kernel.org/r/20220420104907.36275-1-nbd@nbd.name Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When irq-xtensa-mx chip is used in non-SMP configuration its
irq_set_affinity callback is not called leaving IRQ affinity set empty.
As a result IRQ delivery does not work in that configuration.
Initialize IRQ affinity of the xtensa MX interrupt distributor to CPU 0
for all external IRQ lines.
Cc: stable@vger.kernel.org Signed-off-by: Max Filippov <jcmvbkbc@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Register ARMADA_370_XP_INT_FABRIC_MASK_OFFS is Armada 370 and XP specific
and on new Armada platforms it has different meaning. It does not configure
Performance Counter Overflow interrupt masking. So do not touch this
register on non-A370/XP platforms (A375, A38x and A39x).
Signed-off-by: Pali Rohár <pali@kernel.org> Cc: stable@vger.kernel.org Fixes: 28da06dfd9e4 ("irqchip: armada-370-xp: Enable the PMU interrupts") Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Marc Zyngier <maz@kernel.org> Link: https://lore.kernel.org/r/20220425113706.29310-1-pali@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These patch_text implementations are using stop_machine_cpuslocked
infrastructure with atomic cpu_count. The original idea: When the
master CPU patch_text, the others should wait for it. But current
implementation is using the first CPU as master, which couldn't
guarantee the remaining CPUs are waiting. This patch changes the
last CPU as the master to solve the potential risk.
When multiplying of different types, an overflow is possible even when
storing the result in a larger type. This is because the conversion is
done after the multiplication. So arithmetic overflow and thus in
incorrect value is possible.
Correct an instance of this in the inter packet delay calculation. Fix by
ensuring one of the operands is u64 which will promote the other to u64 as
well ensuring no overflow.
Cc: stable@vger.kernel.org Fixes: 7724105686e7 ("IB/hfi1: add driver files") Link: https://lore.kernel.org/r/20220520183712.48973.29855.stgit@awfm-01.cornelisnetworks.com Reviewed-by: Mike Marciniszyn <mike.marciniszyn@cornelisnetworks.com> Signed-off-by: Dennis Dalessandro <dennis.dalessandro@cornelisnetworks.com> Signed-off-by: Jason Gunthorpe <jgg@nvidia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a config option to guard (future) usage of asm_volatile_goto() that
includes "tied outputs", i.e. "+" constraints that specify both an input
and output parameter. clang-13 has a bug[1] that causes compilation of
such inline asm to fail, and KVM wants to use a "+m" constraint to
implement a uaccess form of CMPXCHG[2]. E.g. the test code fails with
<stdin>:1:29: error: invalid operand in inline asm: '.long (${1:l}) - .'
int foo(int *x) { asm goto (".long (%l[bar]) - .\n": "+m"(*x) ::: bar); return *x; bar: return 0; }
^
<stdin>:1:29: error: unknown token in expression
<inline asm>:1:9: note: instantiated into assembly here
.long () - .
^
2 errors generated.
on clang-13, but passes on gcc (with appropriate asm goto support). The
bug is fixed in clang-14, but won't be backported to clang-13 as the
changes are too invasive/risky.
gcc also had a similar bug[3], fixed in gcc-11, where gcc failed to
account for its behavior of assigning two numbers to tied outputs (one
for input, one for output) when evaluating symbolic references.
The original 'ima' measurement list template contains a hash, defined
as 20 bytes, and a null terminated pathname, limited to 255
characters. Other measurement list templates permit both larger hashes
and longer pathnames. When the "ima" template is configured as the
default, a new measurement list template (ima_template=) must be
specified before specifying a larger hash algorithm (ima_hash=) on the
boot command line.
To avoid this boot command line ordering issue, remove the legacy "ima"
template configuration option, allowing it to still be specified on the
boot command line.
The root cause of this issue is that during the processing of ima_hash,
we would try to check whether the hash algorithm is compatible with the
template. If the template is not set at the moment we do the check, we
check the algorithm against the configured default template. If the
default template is "ima", then we reject any hash algorithm other than
sha1 and md5.
For example, if the compiled default template is "ima", and the default
algorithm is sha1 (which is the current default). In the cmdline, we put
in "ima_hash=sha256 ima_template=ima-ng". The expected behavior would be
that ima starts with ima-ng as the template and sha256 as the hash
algorithm. However, during the processing of "ima_hash=",
"ima_template=" has not been processed yet, and hash_setup would check
the configured hash algorithm against the compiled default: ima, and
reject sha256. So at the end, the hash algorithm that is actually used
will be sha1.
With template "ima" removed from the configured default, we ensure that
the default tempalte would at least be "ima-ng" which allows for
basically any hash algorithm.
This change would not break the algorithm compatibility checks for IMA.
Add H264 level 1.0, 4.1, 4.2 to the list of supported formats.
While the hardware does not fully support these levels, it does support
most of them. The constraints on frame size and pixel formats already
cover the limitation.
This fixes negotiation of level on GStreamer 1.17.1.
The CODA960 manual states that ASO/FMO features of baseline are not
supported, so for this reason this driver should only report
constrained baseline support.
This fixes negotiation issue with constrained baseline content
on GStreamer 1.17.1.
ASO/FMO features are unsupported for the encoder and untested for the
decoder because there is currently no userspace support. Neither GStreamer
parsers nor FFMPEG parsers support ASO/FMO.
projects / thirdparty / kernel / stable.git / log
