timedated: always enable&start the service with highest priority
This removes a special case that was implemented before: if some service
was already enabled, we'd treat it as having higher priority.
From https://bugzilla.redhat.com/show_bug.cgi?id=1735584#c4:
> Setting ntp off and on should give the same result as just setting it
> on. There should be no stickiness (hidden state). It should behave like
> running an ansible role.
>
> The other service might have been enabled because no other was installed at
> the time. If I install a new NTP service with a higher priority, setting ntp
> on should enable and start the new service, and disable all other. Also, if
> for some reason multiple services are enabled, after setting ntp on there
> should be only one enabled to avoid systemd selecting between them randomly
> on the next boot.
timedated: log about unit enablement actions and enhance logs in general
The general idea is that for things which can occur repeatedly, like SetNTP
being called with the same argument, we only log at debug level. For things
which change state, like when we realize that a unit that wasn't enabled
before needs to be enabled, we log at info level.
Also, don't return success if there are no units loaded.
libsystemd-network: make option_append() atomic and make the code a bit clearer
Comparisons are done in the normal order (if (need > available), not if (available < need)),
variables have reduced scope and are renamed for clarity.
The only functional change is that if we return -ENAMETOOLONG, we do that
without modifying the options[] array.
I also added an explanatory comment. The use of one offset to point into three
buffers is not obvious.
Coverity (in CID#1402354) says that sname might be accessed at bad offset, but
I cannot see this happening. We check for available space before writing anything.
time-util: improve detection of synchronized clock
Instead of checking for the STA_UNSYNC flag in the timex status, check
the maximum error. It is updated by the kernel, increasing at a rate of
500 ppm. The maximum value is 16 seconds, which triggers the STA_UNSYNC
flag.
This follows timedatex and allows timedated to correctly detect a clock
synchronized by chronyd when configured to not synchronize the RTC.
test: print an error when networkctl returns an unexpected EC
If networkctl crashes, like recently with SIGABRT, it returns absolutely
no output, which may be confusing during debugging. Help it a little
with a short informative message.
test-execute: skip test_exec_systemcallfilter_system under ASan
This particular test case keeps intermittently failing due to crashing
LSan when running under clang+ASan. Generally, sanitizers don't
like seccomp filters, so the best option here is to just switch this
test off for this scenario.
`adduser` is in certain cases a standalone package which provides a
better user experience. In other cases it's just a symlink to `useradd`.
And some distributions don't have `adduser` at all, like Arch Linux.
Let's use the `useradd` binary instead, which should provide the same
functionality everywhere.
v2:
- do not watch mtime of transient and generated dirs
We'd reload the map after every transient unit we created, which we don't
need to do, since we create those units ourselves and know their fragment
path.
This reworks how we load units from disk. Instead of chasing symlinks every
time we are asked to load a unit by name, we slurp all symlinks from disk
and build two hashmaps:
1. from unit name to either alias target, or fragment on disk
(if an alias, we put just the target name in the hashmap, if a fragment
we put an absolute path, so we can distinguish both).
2. from a unit name to all aliases
Reading all this data can be pretty costly (40 ms) on my machine, so we keep it
around for reuse.
The advantage is that we can reliably know what all the aliases of a given unit
are. This means we can reliably load dropins under all names. This fixes #11972.
TEST-15-DROPIN: add test for details of unit aliasing
I adjusted the tests to pass. I don't think the behaviour makes much sense,
even if we ignore the issue with "lazy loading" of aliases. E.g. in the
last section, the fact that dropins for yup@.service and yup@3.service are
not loaded seems to be a plain old bug.
waitid(2) and the libc function signature calls this "exit status", and
uses "exit code" for something different. Let's stick to the same
nomenclature hence.
pid1: use LOG_DEBUG/INFO/NOTICE for unit resource consumption message
We now log at LOG_INFO for any unit. Let's vary the log level
a bit, so that for normal short lived-units (less than 1 sec CPU),
we only log if debugging is enabled.
systemctl: do print all statuses/signals received from pid1
If for some reason we do not know some signal, instead of silently
skipping it, let's print it numerically. Likewise, 'show' is not the
right place to do value filtering for exit codes. If pid1 accepted it,
let's just print it with no fuss.
shared/bus-util: fix dbus serialization of {RestartPrevent,RestartForce,Success}ExitStatus
We were passing 1/4th of the size in bytes as argument. So depending
on the size of the array, either we'd only transfer a subset of values,
or we'd get an alignment error.
bus-util: convert bus_log_{parse,create}_error into defines
With SYSTEMD_LOG_LOCATION=1, it is much more useful to see the location
where the call to bus_log_{parse,create}_error() was made, rather then
the one-line body of the helper function. Also, it's our internal code,
so having a one-line non-inline function doesn't make much sense anyway.
I opted to embed the Bitmap structure directly in the ExitStatusSet.
This means that memory usage is a bit higher for units which don't define
this setting:
Service changes:
/* size: 2720, cachelines: 43, members: 73 */
/* sum members: 2680, holes: 9, sum holes: 39 */
/* sum bitfield members: 7 bits, bit holes: 1, sum bit holes: 1 bits */
/* last cacheline: 32 bytes */
/* size: 2816, cachelines: 44, members: 73 */
/* sum members: 2776, holes: 9, sum holes: 39 */
/* sum bitfield members: 7 bits, bit holes: 1, sum bit holes: 1 bits */
But this way the code is simpler and we do less pointer chasing.
Zach Smith [Mon, 15 Jul 2019 03:01:20 +0000 (20:01 -0700)]
systemd-sleep: use swaps in priority order
In situations where hibernation is requested but resume= and
resume_offset= kernel parameters are not configured, systemd
will attempt to locate a suitable swap location by inspecting
/proc/swaps. This change will use the first suitable swap with
the highest configured priority.
projects / thirdparty / systemd.git / log
