systemd-coredump: Add conflict with shutdown.target
Otherwise a coredump started at the inconvinient moment can stop
shutdown.target leaving the system in a halfway-down state:
Pulling in shutdown.target/start from systemd-poweroff.service/start
Added job shutdown.target/start to transaction.
...
Keeping job shutdown.target/start because of systemd-poweroff.service/start
...
[ OK ] Stopped target Remote File Systems.
shutdown.target: starting held back, waiting for: systemd-networkd.socket
sysinit.target: stopping held back, waiting for: remount_tmp.service
systemd-coredump.socket: Incoming traffic
...
systemd-coredump@0-243-0.service: Trying to enqueue job systemd-coredump@0-243-0.service/start/replace
Added job systemd-coredump@0-243-0.service/start to transaction.
Pulling in systemd-journald.socket/start from systemd-coredump@0-243-0.service/start
Added job systemd-journald.socket/start to transaction.
Pulling in system.slice/start from systemd-journald.socket/start
Added job system.slice/start to transaction.
Pulling in -.slice/start from system.slice/start
Added job -.slice/start to transaction.
Pulling in system-systemd\x2dcoredump.slice/start from systemd-coredump@0-243-0.service/start
Added job system-systemd\x2dcoredump.slice/start to transaction.
Pulling in system.slice/start from system-systemd\x2dcoredump.slice/start
Pulling in shutdown.target/stop from system-systemd\x2dcoredump.slice/start
Added job shutdown.target/stop to transaction.
...
Keeping job systemd-poweroff.service/stop because of umount.target/stop
Keeping job shutdown.target/stop because of systemd-coredump@0-243-0.service/start
The maximum allowed value of the sysfs device index entry was limited to
16383 (2^14-1) to avoid the generation of unreasonable onboard interface
names.
For s390 the index can assume a value of up to 65535 (2^16-1) which is
now allowed depending on the new naming flag NAMING_16BIT_INDEX.
Larger index values are considered unreasonable and remain to be
ignored.
network: do not set nexthop ID, gateway, and multipath routes simultaneously
See kernel's rtm_to_fib_config() in net/ipv4/fib_frontend.c and
rtm_to_fib6_config() in net/ipv6/route.c.
Note that if both gateway and multipath routes are specified, then
kernel ignores gateway. So, strictly speaking, setting both gateway and
multipath routes is allowed by kernel. But such situation is mostly
user's misconfiguration. Let's refuse it.
Note that the conditions newly added in route_configure() are redundant,
as all static configurations are already verified in
route_section_verify(), and dynamic configurations do not set
nexthop_id or multipath routes. Just for safety.
network: do not remove reject type routes more than once
Usually, removing non-existing addresses, routes, and etc, are safe.
However, when multiple interfaces lost their carriers simultaneously,
then manager_drop_routes() and manager_drop_nexthop() are called multiple
times. If a route with a blackhole nexthop is removed in that process,
the later removal requests of the route fail with -EINVAL, rathar
than -ESRCH, as the corresponding nexthop does not exist anymore.
So, let's not remove routes which managed by Manager more than once.
basic/missing-syscalls: only emit one warning about missing numbers
The ifdef pattern is the same for all syscalls, so most of the time, if one is
not defined, all others will too. So let's reduce the noise a bit and emit one
warning in case the support for the architecture is fully missing. (Current
template was copied over from before when we added numbers for each syscall by
hand and stopped making sense when we started generating the header from a
table that is expected to have all syscall numbers.)
hwdb: 60-keyboard:: Update Dell Privacy Local Mic Mute Hotkey (#19261)
This patch fix scancode 0x120001 mapping to key code F20 micmute
The previous scancode is not correct, it will cause the micmute
hotkey no function when testing the mic mute
https://github.com/systemd/systemd/pull/19316 failed with:
[1065/1670] Linking target systemd-hwdb
--- command ---
14:28:29 /root/src/test/hwdb-test.sh
--- stdout ---
./systemd-hwdb does not exist, please build first
I'm not sure what is going on here… In principle meson says that tests may be
called from any directory, but in practice is was always the build directory.
So far we were relying on systemd-hwdb being present in '.', and this worked.
Either way, it's nicer to pass the exact path, so let's do that.
Add support for conditions on the machines firmware
This allows to limit units to machines that run on a certain firmware
type. For device tree defined machines checking against the machine's
compatible is also possible.
network: neighbor: Always add neighbors with replace
We were duplicating setting flags for the message and a combination of
NLM_F_APPEND and NLM_F_CREATE which does not make sense. We should have
been using NLM_F_REPLACE and NLM_F_CREATE since the kernel can
dynamically create neighbors prior to us adding an entry. Otherwise, we
can end up with cases where the message will time out after ~25s even
though the neighbor still gets added. This delays the rest of the setup
of the interface even though the error is ultimately ignored.
system-conf: drop reference to ShutdownWatchdogUsec=
Commit 65224c1d0e50667a87c2c4f840c49d4918718f80 renamed ShutdownWatchdogUsec
into RebootWatchdogUsec but left a reference of ShutdownWatchdogUsec in
system.conf.
Julia Kartseva [Mon, 16 Nov 2020 08:26:44 +0000 (00:26 -0800)]
tests: add test program for SocketBind{Allow|Deny}=
Verify that service exited correctly if valid ports are passed to
SocketBind{Allow|Deny}=
Use `ncat` program starting a listening service binding to a specified
port, e.g.
"timeout --preserve-status -sSIGTERM 1s /bin/nc -l -p ${port} -vv"
Julia Kartseva [Mon, 26 Apr 2021 02:10:40 +0000 (19:10 -0700)]
core, bpf: add socket-bind feature to unit
Add supported and install unit interface for socket-bind feature.
supported verifies that
- unified cgroup hierarchy (cgroup v2) is used
- BPF_FRAMEWORK (libbpf + clang + llvm + bpftool) was available in
compile time
- kernel supports BPF_PROG_TYPE_CGROUP_SOCK_ADDR
- bpf programs can be loaded into kernel
- bpf link can be used
install:
- load bpf_object from bpf skeleton
- resize rules map to fit socket_bind_allow and socket_bind deny rules
from cgroup context
- populate cgroup-bpf maps with rules
- get bpf programs from bpf skeleton
- attach programs to unit cgroup using bpf link
- save bpf link in the unit
* Add `bpf-framework` feature gate with 'auto', 'true' and 'false' choices
* Add libbpf [0] dependency
* Search for clang llvm-strip and bpftool binaries in compile time to
generate bpf skeleton.
For libbpf [0], make 0.2.0 [1] the minimum required version.
If libbpf is satisfied, set HAVE_LIBBPF config option to 1.
If `bpf-framework` feature gate is set to 'auto', means that whether
bpf feature is enabled or now is defined by the presence of all of
libbpf, clang, llvm and bpftool in build
environment.
With 'auto' all dependencies are optional.
If the gate is set to `true`, make all of the libbpf, clang and llvm
dependencies mandatory.
If it's set to `false`, set `BPF_FRAMEWORK` to false and make libbpf
dependency optional.
libbpf dependency is dynamic followed by the common pattern in systemd.
meson, bpf: add build rule for socket_bind program
Julia Kartseva [Sat, 14 Nov 2020 01:02:50 +0000 (17:02 -0800)]
bpf: add build script for bpf programs
Add a build script to compile bpf source code. A program in restricted
C is compiled into an object file. Object file is converted to BPF
skeleton [0] header file.
If build with custom meson build rule, the target header will reside in
build/ directory (not in source tree), e.g the path for socket_bind:
`build/src/core/bpf/socket_bind/socket-bind.skel.h`
Script runs the phases:
* clang to generate *.o from restricted C
* llvm-strip to remove useless DWARF info
* bpf skeleton generation with bpftool
These phases are logged to stderr for debug purposes.
To include BTF debug information, -g option is passed to clang.
Julia Kartseva [Sat, 14 Nov 2020 01:40:17 +0000 (17:40 -0800)]
bpf: add socket-bind BPF program code sources
Introduce BPF program compiled from BPF source code in
restricted C - socket-bind.
It addresses feature request [0].
The goal is to allow systemd services to bind(2) only to a predefined set
of ports. This prevents assigning socket address with unallowed port
to a socket and creating servers listening on that port.
This compliments firewalling feature presenting in systemd:
whereas cgroup/{egress|ingress} hooks act on packets, this doesn't
protect from untrusted service or payload hijacking an important port.
While ports in 0-1023 range are restricted to root only, 1024-65535
range is not protected by any mean.
Performance is another aspect of socket_bind feature since per-packet
cost can be eliminated for some port-based filtering policies.
The feature is implemented with cgroup/bind{4|6} hooks [1].
In contrast to the present systemd approach using raw bpf instructions,
this program is compiled from sources. Stretch goal is to
make bpf ecosystem in systemd more friendly for developer and to clear
path for more BPF programs.
Specifying the test number manually is tedious and prone to errors (as
recently proven). Since we have all the necessary data to work out the
test number, let's do it automagically.
test-unit-serialize: add a very basic test that command deserialization works
We should test both serialization and deserialization works properly.
But the serialization/deserialization code is deeply entwined with the
manager state, and I think quite a bit of refactoring will be required before
this is possible. But let's at least add this simple test for now.
After 4b30f2e135ee84041bb597edca7225858f4ef4fb, reading stable_secret
sysctl property fails with -ENOMEM, instead of -EIO.
This is due to read_full_virtual_file() uses read() as the backend while
read_one_line_file() uses fgetc(). And each functions return different
error on fails.
Anyway, the failure is harmless here. So, the log message and comment is
updated.
homectl: pick up cached/credential store/env var passwords *before* issuing first request
Previously, we'd generally attempt the operation first, without any
passwords, and only query for a password if that operation then fails
and asks for one. This is done to improve compatibility with
password-less authentication schemes, such as security tokens and
similar.
This patch modifies this slightly: if a password can be acquired cheaply
via the keyring password cache, the $CREDENTIALS_PATH credential store,
or the $PASSWORD/$PIN environment variables, acquire it *before* issuing
the first requested.
This should save us a pointless roundtrip, and should never hurt.
tests: use setfacl to give $SUDO_USER read permissions on artifacts
We have to invoke the tests as superuser, and not being able to read
the journal as the invoking user is annoying. I don't think there are
any security considerations here, since the invoking user can already
put arbitrary code in the Makefile and test scripts which get executed
with root privileges.
fstab-generator: clean up mount point flags handling
Let's rename MountpointsFlags → MountPointFlags. In most of our codebase
we name things mount_point/MountPoint rather than mountpoint/Mountpoint,
do so here too.
Also, prefix the enum values with "MOUNT_". The fact the enum values
weren#t prefixed was pretty unique in our codebase, and pretty
surprising. Let's fix that.
This is just refactoring, no actual change in behaviour
test: move the logic to support /skipped into shared logic
The logic to query test state was rather complex. I don't quite grok the point
of ret=$((ret+1))… But afaics, the precise result was always ignored by the
caller anyway.
projects / thirdparty / systemd.git / log
