Yian Chen [Sat, 21 May 2022 00:21:15 +0000 (17:21 -0700)]
iommu/vt-d: Fix PCI bus rescan device hot add
Notifier calling chain uses priority to determine the execution
order of the notifiers or listeners registered to the chain.
PCI bus device hot add utilizes the notification mechanism.
The current code sets low priority (INT_MIN) to Intel
dmar_pci_bus_notifier and postpones DMAR decoding after adding
new device into IOMMU. The result is that struct device pointer
cannot be found in DRHD search for the new device's DMAR/IOMMU.
Subsequently, the device is put under the "catch-all" IOMMU
instead of the correct one. This could cause system hang when
device TLB invalidation is sent to the wrong IOMMU. Invalidation
timeout error and hard lockup have been observed and data
inconsistency/crush may occur as well.
This patch fixes the issue by setting a positive priority(1) for
dmar_pci_bus_notifier while the priority of IOMMU bus notifier
uses the default value(0), therefore DMAR decoding will be in
advance of DRHD search for a new device to find the correct IOMMU.
Following is a 2-step example that triggers the bug by simulating
PCI device hot add behavior in Intel Sapphire Rapids server.
Guangbin Huang [Tue, 28 Jun 2022 06:34:19 +0000 (14:34 +0800)]
drivers/perf: hisi: add driver for HNS3 PMU
HNS3(HiSilicon Network System 3) PMU is RCiEP device in HiSilicon SoC NIC,
supports collection of performance statistics such as bandwidth, latency,
packet rate and interrupt rate.
NIC of each SICL has one PMU device for it. Driver registers each PMU
device to perf, and exports information of supported events, filter mode of
each event, bdf range, hardware clock frequency, identifier and so on via
sysfs.
Each PMU device has its own registers of control, counters and interrupt,
and it supports 8 hardware events, each hardward event has its own
registers for configuration, counters and interrupt.
Filter options contains:
config - select event
port - select physical port of nic
tc - select tc(must be used with port)
func - select PF/VF
queue - select queue of PF/VF(must be used with func)
intr - select interrupt number(must be used with func)
global - select all functions of IO DIE
Currently, when the CPU is doing suspend to ram, we don't
save pmu counter register and its content will be lost.
To ensure perf profiling is not affected by suspend to ram,
this patch is based on arm_pmu CPU_PM notifier and implements riscv
pmu pm notifier. In the pm notifier, we stop the counter and update
the counter value before suspend and start the counter after resume.
Michael Roth [Wed, 6 Jul 2022 02:53:15 +0000 (21:53 -0500)]
x86/compressed/64: Add identity mappings for setup_data entries
The decompressed kernel initially relies on the identity map set up by
the boot/compressed kernel for accessing things like boot_params. With
the recent introduction of SEV-SNP support, the decompressed kernel
also needs to access the setup_data entries pointed to by
boot_params->hdr.setup_data.
This can lead to a crash in the kexec kernel during early boot due to
these entries not currently being included in the initial identity map,
see thread at Link below.
Include mappings for the setup_data entries in the initial identity map.
[ bp: Massage commit message and use a helper var for better readability. ]
Although harmless, the return statement in kvm_unexpected_el2_exception
is rather confusing as the function itself has a void return type. The
C standard is also pretty clear that "A return statement with an
expression shall not appear in a function whose return type is void".
Given that this return statement does not seem to add any actual value,
let's not pointlessly violate the standard.
Build-tested with GCC 10 and CLANG 13 for good measure, the disassembled
code is identical with or without the return statement.
David S. Miller [Wed, 6 Jul 2022 07:16:48 +0000 (08:16 +0100)]
Merge branch 'octeontx2-af-next'
Ratheesh Kannoth says:
====================
octeontx2: *** Exact Match Table and Field hash ***
*** Exact match table and Field hash support for CN10KB silicon ***
Ratheesh Kannoth (11):
These patch series enables exact match table in CN10KB silicon. Legacy
silicon used NPC mcam to do packet fields/channel matching for NPC rules.
NPC mcam resources exahausted as customer use case increased.
Supporting many DMAC filter becomes a challenge, as RPM based filter
count is less. Exact match table has 4way 2K entry table and a 32 entry
fully associative cam table. Second table is to handle hash
table collision overflows in 4way 2K entry table. Enabling exact match table
results in KEX key to be appended with Hit/Miss status. This can be used
to match in NPC mcam for a more generic rule and drop those packets than
having DMAC drop rules for each DMAC entry in NPC mcam.
octeontx2-af: Exact match support
octeontx2-af: Exact match scan from kex profile
octeontx2-af: devlink configuration support
octeontx2-af: FLR handler for exact match table.
octeontx2-af: Drop rules for NPC MCAM
octeontx2-af: Debugsfs support for exact match.
octeontx2: Modify mbox request and response structures
octeontx2-af: Wrapper functions for mac addr add/del/update/reset
octeontx2-af: Invoke exact match functions if supported
octeontx2-pf: Add support for exact match table.
octeontx2-af: Enable Exact match flag in kex profile
Suman Ghosh (1):
CN10KB variant of CN10K series of silicons supports
a new feature where in a large protocol field
(eg 128bit IPv6 DIP) can be condensed into a small
hashed 32bit data. This saves a lot of space in MCAM key
and allows user to add more protocol fields into the filter.
A max of two such protocol data can be hashed.
This patch adds support for hashing IPv6 SIP and/or DIP.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
octeontx2-af: Wrapper functions for MAC addr add/del/update/reset
These functions are wrappers for mac add/addr/del/update in
exact match table. These will be invoked from mbox handler routines
if exact matct table is supported and enabled.
Signed-off-by: Ratheesh Kannoth <rkannoth@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
octeontx2: Modify mbox request and response structures
Exact match table modification requires wider fields as it has
more number of slots to fill in. Modifying an entry in exact match
table may cause hash collision and may be required to delete entry
from 4-way 2K table and add to fully associative 32 entry CAM table.
Signed-off-by: Ratheesh Kannoth <rkannoth@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
NPC exact match table installs drop on hit rules in
NPC mcam for each channel. This rule has broadcast and multicast
bits cleared. Exact match bit cleared and channel bits
set. If exact match table hit bit is 0, corresponding NPC mcam
drop rule will be hit for the packet and will be dropped.
Signed-off-by: Ratheesh Kannoth <rkannoth@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
CN10KB silicon supports Exact match feature. This feature can be disabled
through devlink configuration. Devlink command fails if DMAC filter rules
are already present. Once disabled, legacy RPM based DMAC filters will be
configured.
Signed-off-by: Ratheesh Kannoth <rkannoth@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
CN10KB silicon supports exact match table. Scanning KEX
profile should check for exact match feature is enabled
and then set profile masks properly.
These kex profile masks are required to configure NPC
MCAM drop rules. If there is a miss in exact match table,
these drop rules will drop those packets.
Signed-off-by: Ratheesh Kannoth <rkannoth@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
CN10KB silicon has support for exact match table. This table
can be used to match maimum 64 bit value of KPU parsed output.
Hit/non hit in exact match table can be used as a KEX key to
NPC mcam.
This patch makes use of Exact match table to increase number of
DMAC filters supported. NPC mcam is no more need for each of these
DMAC entries as will be populated in Exact match table.
This patch implements following
1. Initialization of exact match table only for CN10KB.
2. Add/del/update interface function for exact match table.
Signed-off-by: Ratheesh Kannoth <rkannoth@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
CN10KB variant of CN10K series of silicons supports
a new feature where in a large protocol field
(eg 128bit IPv6 DIP) can be condensed into a small
hashed 32bit data. This saves a lot of space in MCAM key
and allows user to add more protocol fields into the filter.
A max of two such protocol data can be hashed.
This patch adds support for hashing IPv6 SIP and/or DIP.
Signed-off-by: Suman Ghosh <sumang@marvell.com> Signed-off-by: Ratheesh Kannoth <rkannoth@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Simon Horman [Tue, 5 Jul 2022 07:36:04 +0000 (08:36 +0100)]
nfp: enable TSO by default for nfp netdev
We can benefit from TSO when the host CPU is not powerful enough,
so enable it by default now.
Signed-off-by: Yinjun Zhang <yinjun.zhang@corigine.com> Reviewed-by: Louis Peens <louis.peens@corigine.com> Signed-off-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: David S. Miller <davem@davemloft.net>
nfp: allow TSO packets with metadata prepended in NFDK path
Packets with metadata prepended can be correctly handled in
firmware when TSO is enabled, now remove the error path and
related comments. Since there's no existing firmware that
uses prepended metadata, no need to add compatibility check
here.
Signed-off-by: Yinjun Zhang <yinjun.zhang@corigine.com> Reviewed-by: Louis Peens <louis.peens@corigine.com> Signed-off-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: David S. Miller <davem@davemloft.net>
soundwire: qcom: Add flag for software clock gating check
Validate software clock gating required or not and do software
clock gating on hclk if soundwire is operational and keep it
running by adding flag in private data structure.
This is to avoid conflict between older architectures,
where software clock gating is not required and on latest
architectures, where software clock gating is mandatory.
soundwire: qcom: Add support for controlling audio CGCR from HLOS
Add support for controlling soundwire audio CGCR interface using clock
framework to make hclk ungating with software. As per new hardware
changes, software has to always ungate hclk if soundwire is operational
and keep it running. This requirement is for latest LPASS chipsets for
RX, TX and WSA path to work.
soundwire: intel: use pm_runtime_resume() on component probe
During the card registration, transactions on the SoundWire bus can be
initiated. If the ALSA card is registered after the bus suspends,
timeouts can be seen while reading/writing codec registers. This is
extremely easy to reproduce in driver bind/unbind tests.
In an initial experiment, the ASoC soc-component.c code was modified
to initiate a pm_runtime resume on a component probe. The results
showed this was too invasive. Instead this patch suggests resuming the
SoundWire component only.
Because of the parent-child hierarchy enforced by the pm_runtime
framework, it can be argued that the codec component probe should be
enough to resume all necessary devices, and indeed the same resume
will be applied to SoundWire codecs used on Intel platforms.
Calling pm_runtime_resume() on both the Intel and codec sides has the
benefit of resuming the bus without assuming any order during the card
registration. The first component on a dailink to be probed will
resume the bus. In addition, if a codec driver did not implement this
transition, the Intel component would still resume the bus and avoid
timeouts on card registration.
soundwire: revisit driver bind/unbind and callbacks
In the SoundWire probe, we store a pointer from the driver ops into
the 'slave' structure. This can lead to kernel oopses when unbinding
codec drivers, e.g. with the following sequence to remove machine
driver and codec driver.
The full details can be found in the BugLink below, for reference the
two following examples show different cases of driver ops/callbacks
being invoked after the driver .remove().
This was not detected earlier in Intel tests since the tests first
remove the parent PCI device and shut down the bus. The sequence
above is a corner case which keeps the bus operational but without a
driver bound.
While trying to solve this kernel oopses, it became clear that the
existing SoundWire bus does not deal well with the unbind case.
Commit 528be501b7d4a ("soundwire: sdw_slave: add probe_complete structure and new fields")
added a 'probed' status variable and a 'probe_complete'
struct completion. This status is however not reset on remove and
likewise the 'probe complete' is not re-initialized, so the
bind/unbind/bind test cases would fail. The timeout used before the
'update_status' callback was also a bad idea in hindsight, there
should really be no timing assumption as to if and when a driver is
bound to a device.
An initial draft was based on device_lock() and device_unlock() was
tested. This proved too complicated, with deadlocks created during the
suspend-resume sequences, which also use the same device_lock/unlock()
as the bind/unbind sequences. On a CometLake device, a bad DSDT/BIOS
caused spurious resumes and the use of device_lock() caused hangs
during suspend. After multiple weeks or testing and painful
reverse-engineering of deadlocks on different devices, we looked for
alternatives that did not interfere with the device core.
A bus notifier was used successfully to keep track of DRIVER_BOUND and
DRIVER_UNBIND events. This solved the bind-unbind-bind case in tests,
but it can still be defeated with a theoretical corner case where the
memory is freed by a .remove while the callback is in use. The
notifier only helps make sure the driver callbacks are valid, but not
that the memory allocated in probe remains valid while the callbacks
are invoked.
This patch suggests the introduction of a new 'sdw_dev_lock' mutex
protecting probe/remove and all driver callbacks. Since this mutex is
'local' to SoundWire only, it does not interfere with existing locks
and does not create deadlocks. In addition, this patch removes the
'probe_complete' completion, instead we directly invoke the
'update_status' from the probe routine. That removes any sort of
timing dependency and a much better support for the device/driver
model, the driver could be bound before the bus started, or eons after
the bus started and the hardware would be properly initialized in all
cases.
BugLink: https://github.com/thesofproject/linux/issues/3531 Fixes: 56d4fe31af77 ("soundwire: Add MIPI DisCo property helpers") Fixes: 528be501b7d4a ("soundwire: sdw_slave: add probe_complete structure and new fields") Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Reviewed-by: Rander Wang <rander.wang@intel.com> Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com> Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com> Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com> Link: https://lore.kernel.org/r/20220621225641.221170-2-pierre-louis.bossart@linux.intel.com Signed-off-by: Vinod Koul <vkoul@kernel.org>
soundwire: bus_type: fix remove and shutdown support
The bus sdw_drv_remove() and sdw_drv_shutdown() helpers are used
conditionally, if the driver provides these routines.
These helpers already test if the driver provides a .remove or
.shutdown callback, so there's no harm in invoking the
sdw_drv_remove() and sdw_drv_shutdown() unconditionally.
In addition, the current code is imbalanced with
dev_pm_domain_attach() called from sdw_drv_probe(), but
dev_pm_domain_detach() called from sdw_drv_remove() only if the driver
provides a .remove callback.
dt-bindings: dma: dw-axi-dmac: extend the number of interrupts
The Canaan k210 apparently has a Sysnopsys Designware AXI DMA
controller, but according to the documentation & devicetree it has 6
interrupts rather than the standard one. Support the 6 interrupt
configuration by unconditionally extending the binding to a maximum of
8 per-channel interrupts thereby matching the number of possible
channels.
The feature test to detect the availability of zlib in bpftool's
Makefile does not bring much. The library is not optional: it may or may
not be required along libbfd for disassembling instructions, but in any
case it is necessary to build feature.o or even libbpf, on which bpftool
depends.
If we remove the feature test, we lose the nicely formatted error
message, but we get a compiler error about "zlib.h: No such file or
directory", which is equally informative. Let's get rid of the test.
Dmitry Osipenko [Fri, 20 May 2022 18:14:32 +0000 (21:14 +0300)]
dmaengine: pl330: Fix lockdep warning about non-static key
The DEFINE_SPINLOCK() macro shouldn't be used for dynamically allocated
spinlocks. The lockdep warns about this and disables locking validator.
Fix the warning by making lock static.
INFO: trying to register non-static key.
The code is fine but needs lockdep annotation, or maybe
you didn't initialize this object before use?
turning off the locking correctness validator.
Hardware name: Radxa ROCK Pi 4C (DT)
Call trace:
dump_backtrace.part.0+0xcc/0xe0
show_stack+0x18/0x6c
dump_stack_lvl+0x8c/0xb8
dump_stack+0x18/0x34
register_lock_class+0x4a8/0x4cc
__lock_acquire+0x78/0x20cc
lock_acquire.part.0+0xe0/0x230
lock_acquire+0x68/0x84
_raw_spin_lock_irqsave+0x84/0xc4
add_desc+0x44/0xc0
pl330_get_desc+0x15c/0x1d0
pl330_prep_dma_cyclic+0x100/0x270
snd_dmaengine_pcm_trigger+0xec/0x1c0
dmaengine_pcm_trigger+0x18/0x24
...
Merge branch 'cleanup the legacy probe_event on failed scenario'
Chuang Wang says:
====================
A potential scenario, when an error is returned after
add_uprobe_event_legacy() in perf_event_uprobe_open_legacy(), or
bpf_program__attach_perf_event_opts() in
bpf_program__attach_uprobe_opts() returns an error, the uprobe_event
that was previously created is not cleaned.
At the same time, the legacy kprobe_event also have similar problems.
With these patches, whenever an error is returned, it ensures that
the created kprobe_event/uprobe_event is cleaned.
V1 -> v3:
- add detail commits
- call remove_kprobe_event_legacy() on failed bpf_program__attach_perf_event_opts()
v3 -> v4:
- cleanup the legacy kprobe_event on failed add/attach_event
====================
Chuang Wang [Wed, 29 Jun 2022 15:18:47 +0000 (23:18 +0800)]
libbpf: Cleanup the legacy uprobe_event on failed add/attach_event()
A potential scenario, when an error is returned after
add_uprobe_event_legacy() in perf_event_uprobe_open_legacy(), or
bpf_program__attach_perf_event_opts() in
bpf_program__attach_uprobe_opts() returns an error, the uprobe_event
that was previously created is not cleaned.
So, with this patch, when an error is returned, fix this by adding
remove_uprobe_event_legacy()
Chuang Wang [Wed, 29 Jun 2022 15:18:45 +0000 (23:18 +0800)]
libbpf: Cleanup the legacy kprobe_event on failed add/attach_event()
Before the 0bc11ed5ab60 commit ("kprobes: Allow kprobes coexist with
livepatch"), in a scenario where livepatch and kprobe coexist on the
same function entry, the creation of kprobe_event using
add_kprobe_event_legacy() will be successful, at the same time as a
trace event (e.g. /debugfs/tracing/events/kprobe/XXX) will exist, but
perf_event_open() will return an error because both livepatch and kprobe
use FTRACE_OPS_FL_IPMODIFY. As follows:
1) add a livepatch
$ insmod livepatch-XXX.ko
2) add a kprobe using tracefs API (i.e. add_kprobe_event_legacy)
On Andrii Nakryiko's comment, few error paths in
bpf_program__attach_kprobe_opts() that should need to call
remove_kprobe_event_legacy().
With this patch, whenever an error is returned after
add_kprobe_event_legacy() or bpf_program__attach_perf_event_opts(), this
ensures that the created kprobe_event is cleaned.
This patch set proposes the addition of a new way for performing type queries to
BPF. It introduces the "type matches" relation, similar to what is already
present with "type exists" (in the form of bpf_core_type_exists).
"type exists" performs fairly superficial checking, mostly concerned with
whether a type exists in the kernel and is of the same kind (enum/struct/...).
Notably, compatibility checks for members of composite types is lacking.
The newly introduced "type matches" (bpf_core_type_matches) fills this gap in
that it performs stricter checks: compatibility of members and existence of
similarly named enum variants is checked as well. E.g., given these definitions:
struct task_struct___og { int pid; int tgid; };
struct task_struct___foo { int foo; }
'task_struct___og' would "match" the kernel type 'task_struct', because the
members match up, while 'task_struct___foo' would not match, because the
kernel's 'task_struct' has no member named 'foo'.
More precisely, the "type match" relation is defined as follows (copied from
source):
- modifiers and typedefs are stripped (and, hence, effectively ignored)
- generally speaking types need to be of same kind (struct vs. struct, union
vs. union, etc.)
- exceptions are struct/union behind a pointer which could also match a
forward declaration of a struct or union, respectively, and enum vs.
enum64 (see below)
Then, depending on type:
- integers:
- match if size and signedness match
- arrays & pointers:
- target types are recursively matched
- structs & unions:
- local members need to exist in target with the same name
- for each member we recursively check match unless it is already behind a
pointer, in which case we only check matching names and compatible kind
- enums:
- local variants have to have a match in target by symbolic name (but not
numeric value)
- size has to match (but enum may match enum64 and vice versa)
- function pointers:
- number and position of arguments in local type has to match target
- for each argument and the return value we recursively check match
Enabling this feature requires a new relocation to be made known to the
compiler. This is being taken care of for LLVM as part of
https://reviews.llvm.org/D126838.
If applied, among other things, usage of this functionality could have helped
flag issues such as the one discussed here
https://lore.kernel.org/all/93a20759600c05b6d9e4359a1517c88e06b44834.camel@fb.com/
earlier.
Suggested-by: Andrii Nakryiko <andrii@kernel.org>
---
Changelog:
v2 -> v3:
- renamed btfgen_mark_types_match
- covered BTF_KIND_RESTRICT in type match marking logic
- used bpf_core_names_match in more places
- reworked "behind pointer" logic
- added test using live task_struct
v1 -> v2:
- deduplicated and moved core algorithm into relo_core.c
- adjusted bpf_core_names_match to get btf_type passed in
- removed some length equality checks before strncmp usage
- correctly use kflag from targ_t instead of local_t
- added comment for meaning of kflag w/ FWD kind
- __u32 -> u32
- handle BTF_KIND_FWD properly in bpftool marking logic
- rebased
====================
Daniel Müller [Tue, 28 Jun 2022 16:01:27 +0000 (16:01 +0000)]
selftests/bpf: Add type match test against kernel's task_struct
This change extends the existing core_reloc/kernel test to include a
type match check of a local task_struct against the kernel's definition
-- which we assume to succeed.
Daniel Müller [Tue, 28 Jun 2022 16:01:26 +0000 (16:01 +0000)]
selftests/bpf: Add nested type to type based tests
This change extends the type based tests with another struct type (in
addition to a_struct) to check relocations against: a_complex_struct.
This type is nested more deeply to provide additional coverage of
certain paths in the type match logic.
Daniel Müller [Tue, 28 Jun 2022 16:01:25 +0000 (16:01 +0000)]
selftests/bpf: Add test checking more characteristics
This change adds another type-based self-test that specifically aims to
test some more characteristics of the TYPE_MATCH logic. Specifically, it
covers a few more potential differences between types, such as different
orders, enum variant values, and integer signedness.
Daniel Müller [Tue, 28 Jun 2022 16:01:24 +0000 (16:01 +0000)]
selftests/bpf: Add type-match checks to type-based tests
Now that we have type-match logic in both libbpf and the kernel, this
change adjusts the existing BPF self tests to check this functionality.
Specifically, we extend the existing type-based tests to check the
previously introduced bpf_core_type_matches macro.
Daniel Müller [Tue, 28 Jun 2022 16:01:21 +0000 (16:01 +0000)]
bpf, libbpf: Add type match support
This patch adds support for the proposed type match relation to
relo_core where it is shared between userspace and kernel. It plumbs
through both kernel-side and libbpf-side support.
The matching relation is defined as follows (copy from source):
- modifiers and typedefs are stripped (and, hence, effectively ignored)
- generally speaking types need to be of same kind (struct vs. struct, union
vs. union, etc.)
- exceptions are struct/union behind a pointer which could also match a
forward declaration of a struct or union, respectively, and enum vs.
enum64 (see below)
Then, depending on type:
- integers:
- match if size and signedness match
- arrays & pointers:
- target types are recursively matched
- structs & unions:
- local members need to exist in target with the same name
- for each member we recursively check match unless it is already behind a
pointer, in which case we only check matching names and compatible kind
- enums:
- local variants have to have a match in target by symbolic name (but not
numeric value)
- size has to match (but enum may match enum64 and vice versa)
- function pointers:
- number and position of arguments in local type has to match target
- for each argument and the return value we recursively check match
Daniel Müller [Tue, 28 Jun 2022 16:01:19 +0000 (16:01 +0000)]
bpftool: Honor BPF_CORE_TYPE_MATCHES relocation
bpftool needs to know about the newly introduced BPF_CORE_TYPE_MATCHES
relocation for its 'gen min_core_btf' command to work properly in the
present of this relocation.
Specifically, we need to make sure to mark types and fields so that they
are present in the minimized BTF for "type match" checks to work out.
However, contrary to the existing btfgen_record_field_relo, we need to
rely on the BTF -- and not the spec -- to find fields. With this change
we handle this new variant correctly. The functionality will be tested
with follow on changes to BPF selftests, which already run against a
minimized BTF created with bpftool.
Daniel Müller [Tue, 28 Jun 2022 16:01:18 +0000 (16:01 +0000)]
bpf: Introduce TYPE_MATCH related constants/macros
In order to provide type match support we require a new type of
relocation which, in turn, requires toolchain support. Recent LLVM/Clang
versions support a new value for the last argument to the
__builtin_preserve_type_info builtin, for example.
With this change we introduce the necessary constants into relevant
header files, mirroring what the compiler may support.
Michael Walle [Mon, 4 Jul 2022 15:36:54 +0000 (17:36 +0200)]
net: lan966x: hardcode the number of external ports
Instead of counting the child nodes in the device tree, hardcode the
number of ports in the driver itself. The counting won't work at all
if an ethernet port is marked as disabled, e.g. because it is not
connected on the board at all.
It turns out that the LAN9662 and LAN9668 use the same switching IP
with the same synthesis parameters. The only difference is that the
output ports are not connected. Thus, we can just hardcode the
number of physical ports to 8.
Fixes: db8bcaad5393 ("net: lan966x: add the basic lan966x driver") Signed-off-by: Michael Walle <michael@walle.cc> Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com> Link: https://lore.kernel.org/r/20220704153654.1167886-1-michael@walle.cc Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Vladimir Oltean [Mon, 4 Jul 2022 19:02:41 +0000 (22:02 +0300)]
net: dsa: felix: build as module when tc-taprio is module
felix_vsc9959.c calls taprio_offload_get() and taprio_offload_free(),
symbols exported by net/sched/sch_taprio.c. As such, we must disallow
building the Felix driver as built-in when the symbol exported by
tc-taprio isn't present in the kernel image.
Vladimir Oltean [Mon, 4 Jul 2022 19:02:40 +0000 (22:02 +0300)]
net: sched: provide shim definitions for taprio_offload_{get,free}
All callers of taprio_offload_get() and taprio_offload_free() prior to
the blamed commit are conditionally compiled based on CONFIG_NET_SCH_TAPRIO.
felix_vsc9959.c is different; it provides vsc9959_qos_port_tas_set()
even when taprio is compiled out.
Provide shim definitions for the functions exported by taprio so that
felix_vsc9959.c is able to compile. vsc9959_qos_port_tas_set() in that
case is dead code anyway, and ocelot_port->taprio remains NULL, which is
fine for the rest of the logic.
Fixes: 1c9017e44af2 ("net: dsa: felix: keep reference on entire tc-taprio config") Reported-by: Colin Foster <colin.foster@in-advantage.com> Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Tested-by: Colin Foster <colin.foster@in-advantage.com> Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com> Link: https://lore.kernel.org/r/20220704190241.1288847-1-vladimir.oltean@nxp.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Serge Semin [Fri, 24 Jun 2022 14:34:28 +0000 (17:34 +0300)]
PCI: dwc-plat: Drop dw_plat_pcie_of_match[] forward declaration
The dw_plat_pcie_of_match[] forward declaration was required when
dw_plat_pcie_probe() called of_match_device(). 5c204204cf24 ("PCI:
designware-plat: Prefer of_device_get_match_data()") replaced that with
of_device_get_match_data(), which no longer needs the declaration.
Save the return value in "ret" for all three cases (DW_PCIE_RC_TYPE,
DW_PCIE_EP_TYPE, default) handled by dw_plat_pcie_probe() and return from a
single place.
Serge Semin [Fri, 24 Jun 2022 14:34:25 +0000 (17:34 +0300)]
PCI: dwc: Rename struct pcie_port to dw_pcie_rp
All of the DW PCIe core driver entities except the pcie_port struct have
names with the "dw_" prefix to distinguish local and common PCIe name
spaces, and endpoint-related entities have an "_ep" suffix.
Rename struct pcie_port to dw_pcie_rp to make it more consistent with other
names.
Serge Semin [Fri, 24 Jun 2022 14:34:24 +0000 (17:34 +0300)]
PCI: dwc: Move io_cfg_atu_shared to struct pcie_port
The io_cfg_atu_shared flag is set if there is an outbound iATU window used
for both config space accesses and IO port transfers.
Since the flag semantic is purely Root Port specific, it's not used in
either the DW PCIe common code or in the DW PCIe Endpoint driver. Move it
to the struct pcie_port and rename to cfg0_io_shared.
Serge Semin [Fri, 24 Jun 2022 14:34:23 +0000 (17:34 +0300)]
PCI: dwc: Add start_link/stop_link inlines
Factor out this pattern:
if (!pci->ops || !pci->ops->start_link)
return -EINVAL;
return pci->ops->start_link(pci);
into a new dw_pcie_start_link() wrapper and do the same for the stop_link()
method.
Note that dw_pcie_ep_start() previously returned -EINVAL if there was no
platform start_link() method, which didn't make much sense since that is
not an error. It will now return 0 in that case.
As a side-effect, drop the empty start_link() and dummy dw_pcie_ops
instances from the generic DW PCIe and Layerscape EP platform drivers.
Serge Semin [Fri, 24 Jun 2022 14:34:22 +0000 (17:34 +0300)]
PCI: dwc: Reuse local pointer to the resource data
dw_pcie_host_init() has two instances of the resource structure pointers
used in unrelated places. It's pointless to have two different local
storages for them since the corresponding code is small and having
resource-specific names doesn't make it more readable.
Convert these parts of the function to use a common pointer to the
resource structure instance.
Serge Semin [Fri, 24 Jun 2022 14:34:21 +0000 (17:34 +0300)]
PCI: dwc: Organize local variable usage
There are several places in the common DW PCIe code with incoherent local
variable usage: a variable is defined and initialized with a structure
field, but the structure pointer is dereferenced to access that field
anyway; the local variable is defined and initialized but either used just
once or not used afterwards in the main part of the subsequent method. It
mainly concerns the pcie_port.dev field. Fix that in the relevant places.
Serge Semin [Fri, 24 Jun 2022 14:34:20 +0000 (17:34 +0300)]
PCI: dwc: Convert dw_pcie_link_up() to use dw_pcie_readl_dbi()
While the rest of the generic DWC PCIe code uses the dedicated IO-mem
accessors, the dw_pcie_link_up() method for some unobvious reason directly
calls readl() to get PortLogic.DEBUG1 register content. Since the way the
DBI bus is accessed can be platform-specific, use dw_pcie_readl_dbi()
instead so dw_pcie_link_up() is slightly more generic.
Serge Semin [Fri, 24 Jun 2022 14:34:19 +0000 (17:34 +0300)]
PCI: dwc: Simplify unrolled iATU detection
The unrolled version of the internal ATU has been available since the DWC
PCIe v4.80a IP core, but it may not be enabled. Per [1], if unrolled ATU
is enabled, the PCIE_ATU_VIEWPORT does not exist and reads as 0xffffffff;
while if unrolled ATU is disabled, PCIE_ATU_VIEWPORT will contain some
zeros.
Simplify dw_pcie_iatu_unroll_enabled() by checking the value of
PCIE_ATU_VIEWPORT.
Serge Semin [Fri, 24 Jun 2022 14:34:16 +0000 (17:34 +0300)]
PCI: dwc: Always enable CDM check if "snps,enable-cdm-check" exists
If the "snps,enable-cdm-check" property exists, we should enable the CDM
check. But previously dw_pcie_setup() could exit before doing so if the
"num-lanes" property was absent or invalid.
Move the CDM enable earlier so we do it regardless of whether "num-lanes"
is present.
Serge Semin [Fri, 24 Jun 2022 14:34:15 +0000 (17:34 +0300)]
PCI: dwc: Deallocate EPC memory on dw_pcie_ep_init() errors
If dw_pcie_ep_init() fails to perform any action after the EPC memory is
initialized and the MSI memory region is allocated, the latter parts won't
be undone thus causing a memory leak. Add a cleanup-on-error path to fix
these leaks.
Serge Semin [Fri, 24 Jun 2022 14:34:14 +0000 (17:34 +0300)]
PCI: dwc: Set INCREASE_REGION_SIZE flag based on limit address
We program the 64-bit ATU limit address (in PCIE_ATU_LIMIT/
PCIE_ATU_UPPER_LIMIT or PCIE_ATU_UNR_LOWER_LIMIT/PCIE_ATU_UNR_UPPER_LIMIT),
but in addition, the PCIE_ATU_INCREASE_REGION_SIZE bit must be set if the
upper 32 bits of the limit address differ from the upper 32 bits of the
base address (see [1,2]).
5b4cf0f65324 ("PCI: dwc: Add upper limit address for outbound iATU") set
PCIE_ATU_INCREASE_REGION_SIZE, but only when the *size* was greater than
4GB. It did not set it when a smaller region crossed a 4GB boundary, e.g.,
[mem 0x0_f0000000-0x1_0fffffff].
Set PCIE_ATU_INCREASE_REGION_SIZE whenever PCIE_ATU_UPPER_LIMIT is
greater than PCIE_ATU_UPPER_BASE.
Serge Semin [Fri, 24 Jun 2022 14:34:13 +0000 (17:34 +0300)]
PCI: dwc: Disable outbound windows only for controllers using iATU
Some DWC-based controllers (e.g., pcie-al.c and pci-keystone.c, identified
by the fact that they override the default dw_child_pcie_ops) use their own
address translation approach instead of the DWC internal ATU (iATU). For
those controllers, skip disabling the iATU outbound windows.
[bhelgaas: commit log, update multiple window comment] Fixes: 458ad06c4cdd ("PCI: dwc: Ensure all outbound ATU windows are reset") Link: https://lore.kernel.org/r/20220624143428.8334-4-Sergey.Semin@baikalelectronics.ru Tested-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Reviewed-by: Rob Herring <robh@kernel.org>
Serge Semin [Fri, 24 Jun 2022 14:34:12 +0000 (17:34 +0300)]
PCI: dwc: Add unroll iATU space support to dw_pcie_disable_atu()
dw_pcie_disable_atu() was introduced by f8aed6ec624f ("PCI: dwc:
designware: Add EP mode support") and supported only the viewport version
of the iATU CSRs.
DW PCIe IP cores v4.80a and newer also support unrolled iATU/eDMA space.
Callers of dw_pcie_disable_atu(), including pci_epc_ops.clear_bar(),
pci_epc_ops.unmap_addr(), and dw_pcie_setup_rc(), don't work correctly when
it is enabled.
Add dw_pcie_disable_atu() support for controllers with unrolled iATU CSRs
enabled.
Serge Semin [Fri, 24 Jun 2022 14:34:11 +0000 (17:34 +0300)]
PCI: dwc: Stop link on host_init errors and de-initialization
It's logically correct to undo everything that was done when an error is
discovered or in the corresponding cleanup counterpart. Otherwise the host
controller will be left in an undetermined state. Since the link is set up
in the host_init method, deactivate it there in the cleanup-on-error block
and stop the link in the antagonistic routine - dw_pcie_host_deinit(). Link
deactivation is platform-specific and should be implemented in
dw_pcie_ops.stop_link().
Fixes: 886a9c134755 ("PCI: dwc: Move link handling into common code") Link: https://lore.kernel.org/r/20220624143428.8334-2-Sergey.Semin@baikalelectronics.ru Tested-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Reviewed-by: Rob Herring <robh@kernel.org>
Jakub Kicinski [Tue, 5 Jul 2022 22:22:28 +0000 (15:22 -0700)]
eth: remove neterion/vxge
The last meaningful change to this driver was made by Jon in 2011.
As much as we'd like to believe that this is because the code is
perfect the chances are nobody is using this hardware.
Because of the size of this driver there is a nontrivial maintenance
cost to keeping this code around, in the last 2 years we're averaging
more than 1 change a month. Some of which require nontrivial review
effort, see commit 877fe9d49b74 ("Revert "drivers/net/ethernet/neterion/vxge:
Fix a use-after-free bug in vxge-main.c"") for example.
Let's try to remove this driver. In general, IMHO, we need to
establish a clear path for shedding dead code. It will be hard
to unless we have some experience trying to delete stuff.
Jason Gunthorpe [Tue, 5 Jul 2022 01:10:50 +0000 (22:10 -0300)]
vfio: Move IOMMU_CAP_CACHE_COHERENCY test to after we know we have a group
The test isn't going to work if a group doesn't exist. Normally this isn't
a problem since VFIO isn't going to create a device if there is no group,
but the special CONFIG_VFIO_NOIOMMU behavior allows bypassing this
prevention. The new cap test effectively forces a group and breaks this
config option.
Move the cap test to vfio_group_find_or_alloc() which is the earliest time
we know we have a group available and thus are not running in noiommu mode.
Fixes: e8ae0e140c05 ("vfio: Require that devices support DMA cache coherence") Reported-by: Xiang Chen <chenxiang66@hisilicon.com> Tested-by: Xiang Chen <chenxiang66@hisilicon.com> Signed-off-by: Jason Gunthorpe <jgg@nvidia.com> Link: https://lore.kernel.org/r/0-v1-e8934b490f36+f4-vfio_cap_fix_jgg@nvidia.com Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Jakub Kicinski [Tue, 5 Jul 2022 21:42:09 +0000 (14:42 -0700)]
Merge tag 'for-net-2022-07-05' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth
Luiz Augusto von Dentz says:
====================
bluetooth pull request for net:
- Fix deadlock when powering on.
* tag 'for-net-2022-07-05' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth:
Bluetooth: core: Fix deadlock on hci_power_on_sync.
====================
Paul E. McKenney [Thu, 16 Jun 2022 16:30:37 +0000 (09:30 -0700)]
context_tracking: Use arch_atomic_read() in __ct_state for KASAN
Context tracking's __ct_state() function can be invoked from noinstr state
where RCU is not watching. This means that its use of atomic_read()
causes KASAN to invoke the non-noinstr __kasan_check_read() function
from the noinstr function __ct_state(). This is problematic because
someone tracing the __kasan_check_read() function could get a nasty
surprise because of RCU not watching.
This commit therefore replaces the __ct_state() function's use of
atomic_read() with arch_atomic_read(), which KASAN does not attempt to
add instrumention to.
Reported-by: kernel test robot <lkp@intel.com> Signed-off-by: Paul E. McKenney <paulmck@kernel.org> Cc: Frederic Weisbecker <frederic@kernel.org> Cc: Marco Elver <elver@google.com> Reviewed-by: Marco Elver <elver@google.com>
MAINTAINERS: Add Paul as context tracking maintainer
Since most of the bits have been imported from kernel/rcu/tree.c and
now that the context tracking code is tightly linked to RCU, add Paul
as a context tracking maintainer.
Also update the context tracking file header accordingly.
Signed-off-by: Frederic Weisbecker <frederic@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Neeraj Upadhyay <quic_neeraju@quicinc.com> Cc: Uladzislau Rezki <uladzislau.rezki@sony.com> Cc: Joel Fernandes <joel@joelfernandes.org> Cc: Boqun Feng <boqun.feng@gmail.com> Cc: Nicolas Saenz Julienne <nsaenz@kernel.org> Cc: Marcelo Tosatti <mtosatti@redhat.com> Cc: Xiongfeng Wang <wangxiongfeng2@huawei.com> Cc: Yu Liao <liaoyu15@huawei.com> Cc: Phil Auld <pauld@redhat.com> Cc: Paul Gortmaker<paul.gortmaker@windriver.com> Cc: Alex Belits <abelits@marvell.com> Signed-off-by: Paul E. McKenney <paulmck@kernel.org> Reviewed-by: Nicolas Saenz Julienne <nsaenzju@redhat.com> Tested-by: Nicolas Saenz Julienne <nsaenzju@redhat.com>
Context tracking's state and dynticks counter are going to be merged
in a single field so that both updates can happen atomically and at the
same time. Prepare for that with converting the state into an atomic_t.
[ paulmck: Apply kernel test robot feedback. ]
Signed-off-by: Frederic Weisbecker <frederic@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Neeraj Upadhyay <quic_neeraju@quicinc.com> Cc: Uladzislau Rezki <uladzislau.rezki@sony.com> Cc: Joel Fernandes <joel@joelfernandes.org> Cc: Boqun Feng <boqun.feng@gmail.com> Cc: Nicolas Saenz Julienne <nsaenz@kernel.org> Cc: Marcelo Tosatti <mtosatti@redhat.com> Cc: Xiongfeng Wang <wangxiongfeng2@huawei.com> Cc: Yu Liao <liaoyu15@huawei.com> Cc: Phil Auld <pauld@redhat.com> Cc: Paul Gortmaker<paul.gortmaker@windriver.com> Cc: Alex Belits <abelits@marvell.com> Signed-off-by: Paul E. McKenney <paulmck@kernel.org> Reviewed-by: Nicolas Saenz Julienne <nsaenzju@redhat.com> Tested-by: Nicolas Saenz Julienne <nsaenzju@redhat.com>
rcu/context-tracking: Move deferred nocb resched to context tracking
To prepare for migrating the RCU eqs accounting code to context tracking,
split the last-resort deferred nocb resched from rcu_user_enter() and
move it into a separate call from context tracking.
Acked-by: Paul E. McKenney <paulmck@kernel.org> Signed-off-by: Frederic Weisbecker <frederic@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Neeraj Upadhyay <quic_neeraju@quicinc.com> Cc: Uladzislau Rezki <uladzislau.rezki@sony.com> Cc: Joel Fernandes <joel@joelfernandes.org> Cc: Boqun Feng <boqun.feng@gmail.com> Cc: Nicolas Saenz Julienne <nsaenz@kernel.org> Cc: Marcelo Tosatti <mtosatti@redhat.com> Cc: Xiongfeng Wang <wangxiongfeng2@huawei.com> Cc: Yu Liao <liaoyu15@huawei.com> Cc: Phil Auld <pauld@redhat.com> Cc: Paul Gortmaker<paul.gortmaker@windriver.com> Cc: Alex Belits <abelits@marvell.com> Signed-off-by: Paul E. McKenney <paulmck@kernel.org> Reviewed-by: Nicolas Saenz Julienne <nsaenzju@redhat.com> Tested-by: Nicolas Saenz Julienne <nsaenzju@redhat.com>
rcu/context_tracking: Move dynticks_nmi_nesting to context tracking
The RCU eqs tracking is going to be performed by the context tracking
subsystem. The related nesting counters thus need to be moved to the
context tracking structure.
Signed-off-by: Frederic Weisbecker <frederic@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Neeraj Upadhyay <quic_neeraju@quicinc.com> Cc: Uladzislau Rezki <uladzislau.rezki@sony.com> Cc: Joel Fernandes <joel@joelfernandes.org> Cc: Boqun Feng <boqun.feng@gmail.com> Cc: Nicolas Saenz Julienne <nsaenz@kernel.org> Cc: Marcelo Tosatti <mtosatti@redhat.com> Cc: Xiongfeng Wang <wangxiongfeng2@huawei.com> Cc: Yu Liao <liaoyu15@huawei.com> Cc: Phil Auld <pauld@redhat.com> Cc: Paul Gortmaker<paul.gortmaker@windriver.com> Cc: Alex Belits <abelits@marvell.com> Signed-off-by: Paul E. McKenney <paulmck@kernel.org> Reviewed-by: Nicolas Saenz Julienne <nsaenzju@redhat.com> Tested-by: Nicolas Saenz Julienne <nsaenzju@redhat.com>
rcu/context_tracking: Move dynticks_nesting to context tracking
The RCU eqs tracking is going to be performed by the context tracking
subsystem. The related nesting counters thus need to be moved to the
context tracking structure.
Acked-by: Paul E. McKenney <paulmck@kernel.org> Signed-off-by: Frederic Weisbecker <frederic@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Neeraj Upadhyay <quic_neeraju@quicinc.com> Cc: Uladzislau Rezki <uladzislau.rezki@sony.com> Cc: Joel Fernandes <joel@joelfernandes.org> Cc: Boqun Feng <boqun.feng@gmail.com> Cc: Nicolas Saenz Julienne <nsaenz@kernel.org> Cc: Marcelo Tosatti <mtosatti@redhat.com> Cc: Xiongfeng Wang <wangxiongfeng2@huawei.com> Cc: Yu Liao <liaoyu15@huawei.com> Cc: Phil Auld <pauld@redhat.com> Cc: Paul Gortmaker<paul.gortmaker@windriver.com> Cc: Alex Belits <abelits@marvell.com> Signed-off-by: Paul E. McKenney <paulmck@kernel.org> Reviewed-by: Nicolas Saenz Julienne <nsaenzju@redhat.com> Tested-by: Nicolas Saenz Julienne <nsaenzju@redhat.com>
rcu/context_tracking: Move dynticks counter to context tracking
In order to prepare for merging RCU dynticks counter into the context
tracking state, move the rcu_data's dynticks field to the context
tracking structure. It will later be mixed within the context tracking
state itself.
[ paulmck: Move enum ctx_state into global scope. ]
Acked-by: Paul E. McKenney <paulmck@kernel.org> Signed-off-by: Frederic Weisbecker <frederic@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Neeraj Upadhyay <quic_neeraju@quicinc.com> Cc: Uladzislau Rezki <uladzislau.rezki@sony.com> Cc: Joel Fernandes <joel@joelfernandes.org> Cc: Boqun Feng <boqun.feng@gmail.com> Cc: Nicolas Saenz Julienne <nsaenz@kernel.org> Cc: Marcelo Tosatti <mtosatti@redhat.com> Cc: Xiongfeng Wang <wangxiongfeng2@huawei.com> Cc: Yu Liao <liaoyu15@huawei.com> Cc: Phil Auld <pauld@redhat.com> Cc: Paul Gortmaker<paul.gortmaker@windriver.com> Cc: Alex Belits <abelits@marvell.com> Signed-off-by: Paul E. McKenney <paulmck@kernel.org> Reviewed-by: Nicolas Saenz Julienne <nsaenzju@redhat.com> Tested-by: Nicolas Saenz Julienne <nsaenzju@redhat.com>
Now rcu_irq_enter/exit() is an unnecessary middle call between
ct_irq_enter/exit() and nmi_irq_enter/exit(). Take this opportunity
to remove the former functions and move the comments above them to the
new entrypoints.
Signed-off-by: Frederic Weisbecker <frederic@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Neeraj Upadhyay <quic_neeraju@quicinc.com> Cc: Uladzislau Rezki <uladzislau.rezki@sony.com> Cc: Joel Fernandes <joel@joelfernandes.org> Cc: Boqun Feng <boqun.feng@gmail.com> Cc: Nicolas Saenz Julienne <nsaenz@kernel.org> Cc: Marcelo Tosatti <mtosatti@redhat.com> Cc: Xiongfeng Wang <wangxiongfeng2@huawei.com> Cc: Yu Liao <liaoyu15@huawei.com> Cc: Phil Auld <pauld@redhat.com> Cc: Paul Gortmaker<paul.gortmaker@windriver.com> Cc: Alex Belits <abelits@marvell.com> Signed-off-by: Paul E. McKenney <paulmck@kernel.org> Reviewed-by: Nicolas Saenz Julienne <nsaenzju@redhat.com> Tested-by: Nicolas Saenz Julienne <nsaenzju@redhat.com>
context_tracking: Take NMI eqs entrypoints over RCU
The RCU dynticks counter is going to be merged into the context tracking
subsystem. Prepare with moving the NMI extended quiescent states
entrypoints to context tracking. For now those are dumb redirection to
existing RCU calls.
Acked-by: Paul E. McKenney <paulmck@kernel.org> Signed-off-by: Frederic Weisbecker <frederic@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Neeraj Upadhyay <quic_neeraju@quicinc.com> Cc: Uladzislau Rezki <uladzislau.rezki@sony.com> Cc: Joel Fernandes <joel@joelfernandes.org> Cc: Boqun Feng <boqun.feng@gmail.com> Cc: Nicolas Saenz Julienne <nsaenz@kernel.org> Cc: Marcelo Tosatti <mtosatti@redhat.com> Cc: Xiongfeng Wang <wangxiongfeng2@huawei.com> Cc: Yu Liao <liaoyu15@huawei.com> Cc: Phil Auld <pauld@redhat.com> Cc: Paul Gortmaker<paul.gortmaker@windriver.com> Cc: Alex Belits <abelits@marvell.com> Signed-off-by: Paul E. McKenney <paulmck@kernel.org> Reviewed-by: Nicolas Saenz Julienne <nsaenzju@redhat.com> Tested-by: Nicolas Saenz Julienne <nsaenzju@redhat.com>
context_tracking: Take IRQ eqs entrypoints over RCU
The RCU dynticks counter is going to be merged into the context tracking
subsystem. Prepare with moving the IRQ extended quiescent states
entrypoints to context tracking. For now those are dumb redirection to
existing RCU calls.
[ paulmck: Apply Stephen Rothwell feedback from -next. ]
[ paulmck: Apply Nathan Chancellor feedback. ]
Acked-by: Paul E. McKenney <paulmck@kernel.org> Signed-off-by: Frederic Weisbecker <frederic@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Neeraj Upadhyay <quic_neeraju@quicinc.com> Cc: Uladzislau Rezki <uladzislau.rezki@sony.com> Cc: Joel Fernandes <joel@joelfernandes.org> Cc: Boqun Feng <boqun.feng@gmail.com> Cc: Nicolas Saenz Julienne <nsaenz@kernel.org> Cc: Marcelo Tosatti <mtosatti@redhat.com> Cc: Xiongfeng Wang <wangxiongfeng2@huawei.com> Cc: Yu Liao <liaoyu15@huawei.com> Cc: Phil Auld <pauld@redhat.com> Cc: Paul Gortmaker<paul.gortmaker@windriver.com> Cc: Alex Belits <abelits@marvell.com> Signed-off-by: Paul E. McKenney <paulmck@kernel.org> Reviewed-by: Nicolas Saenz Julienne <nsaenzju@redhat.com> Tested-by: Nicolas Saenz Julienne <nsaenzju@redhat.com>
context_tracking: Take idle eqs entrypoints over RCU
The RCU dynticks counter is going to be merged into the context tracking
subsystem. Start with moving the idle extended quiescent states
entrypoints to context tracking. For now those are dumb redirections to
existing RCU calls.
[ paulmck: Apply kernel test robot feedback. ]
Signed-off-by: Frederic Weisbecker <frederic@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Neeraj Upadhyay <quic_neeraju@quicinc.com> Cc: Uladzislau Rezki <uladzislau.rezki@sony.com> Cc: Joel Fernandes <joel@joelfernandes.org> Cc: Boqun Feng <boqun.feng@gmail.com> Cc: Nicolas Saenz Julienne <nsaenz@kernel.org> Cc: Marcelo Tosatti <mtosatti@redhat.com> Cc: Xiongfeng Wang <wangxiongfeng2@huawei.com> Cc: Yu Liao <liaoyu15@huawei.com> Cc: Phil Auld <pauld@redhat.com> Cc: Paul Gortmaker<paul.gortmaker@windriver.com> Cc: Alex Belits <abelits@marvell.com> Signed-off-by: Paul E. McKenney <paulmck@kernel.org> Reviewed-by: Nicolas Saenz Julienne <nsaenzju@redhat.com> Tested-by: Nicolas Saenz Julienne <nsaenzju@redhat.com>
Bluetooth: core: Fix deadlock on hci_power_on_sync.
`cancel_work_sync(&hdev->power_on)` was moved to hci_dev_close_sync in
commit [1] to ensure that power_on work is canceled after HCI interface
down.
But, in certain cases power_on work function may call hci_dev_close_sync
itself: hci_power_on -> hci_dev_do_close -> hci_dev_close_sync ->
cancel_work_sync(&hdev->power_on), causing deadlock. In particular, this
happens when device is rfkilled on boot. To avoid deadlock, move
power_on work canceling out of hci_dev_do_close/hci_dev_close_sync.
Deadlock introduced by commit [1] was reported in [2,3] as broken
suspend. Suspend did not work because `hdev->req_lock` held as result of
`power_on` work deadlock. In fact, other BT features were not working.
It was not observed when testing [1] since it was verified without
rfkill in place.
NOTE: It is not needed to cancel power_on work from other places where
hci_dev_do_close/hci_dev_close_sync is called in case:
* Requests were serialized due to `hdev->req_workqueue`. The power_on
work is first in that workqueue.
* hci_rfkill_set_block which won't close device anyway until HCI_SETUP
is on.
* hci_sock_release which runs after hci_sock_bind which ensures
HCI_SETUP was cleared.
As result, behaviour is the same as in pre-dd06ed7 commit, except
power_on work cancel added to hci_dev_close.
[1]: commit ff7f2926114d ("Bluetooth: core: Fix missing power_on work cancel on HCI close")
[2]: https://lore.kernel.org/lkml/20220614181706.26513-1-max.oss.09@gmail.com/
[2]: https://lore.kernel.org/lkml/1236061d-95dd-c3ad-a38f-2dae7aae51ef@o2.pl/
Fixes: ff7f2926114d ("Bluetooth: core: Fix missing power_on work cancel on HCI close") Signed-off-by: Vasyl Vavrychuk <vasyl.vavrychuk@opensynergy.com> Reported-by: Max Krummenacher <max.krummenacher@toradex.com> Reported-by: Mateusz Jonczyk <mat.jonczyk@o2.pl> Tested-by: Max Krummenacher <max.krummenacher@toradex.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Alex Deucher [Tue, 21 Jun 2022 14:10:37 +0000 (10:10 -0400)]
drm/amdgpu/display: disable prefer_shadow for generic fb helpers
Seems to break hibernation. Disable for now until we can root
cause it.
Fixes: 087451f372bf ("drm/amdgpu: use generic fb helpers instead of setting up AMD own's.")
Bug: https://bugzilla.kernel.org/show_bug.cgi?id=216119 Acked-by: Evan Quan <evan.quan@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Alex Deucher [Tue, 21 Jun 2022 14:04:55 +0000 (10:04 -0400)]
drm/amdgpu: keep fbdev buffers pinned during suspend
Was dropped when we converted to the generic helpers.
Fixes: 087451f372bf ("drm/amdgpu: use generic fb helpers instead of setting up AMD own's.") Acked-by: Evan Quan <evan.quan@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Maíra Canal [Thu, 30 Jun 2022 21:53:16 +0000 (18:53 -0300)]
drm/amd/display: Remove unused variables from vba_vars_st
Some variables from the struct vba_vars_st are not referenced in any
other place on the codebase. As they are not used, this commit removes
those variables.
Signed-off-by: Maíra Canal <mairacanal@riseup.net> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
projects / people / ms / linux.git / log
