Add Colibri SSP aka SPI chip select (CS) aka slave select (SS) pins as
either used on Arduino UNO compatible header X18 or Raspberry Pi
compatible header X20.
Marcel Ziswiler [Mon, 16 May 2022 13:47:21 +0000 (15:47 +0200)]
ARM: dts: imx7-colibri: clean-up usdhc1 and add sleep config
Adding no-1-8-v property to usdhc1 to disable +1.8V signaling (UHS-I)
mode on SoM dtsi level.
Clean up no-1-8-v from Aster carrier board dtsi, which is using defaults
from SoM dtsi and is not UHS-I capable.
A carrier board may have a MMC/SD card slot with a switchable power
supply. Add a pinctrl sleep used when the card power is off to avoid
backfeeding to the card and add the "sleep" pinctrl to the usdhc1
controller.
ARM: dts: imx7-colibri: add delay for on-module phy supply
There is a significant time required for PHY Micrel KSZ8041 to power up.
Add a delay on start-up/wake-up before the FEC starts communicating with
the PHY.
LDO1 takes 6 ms, R39 + C44 takes ~100ms, the KSZ8041 datasheet asks for
~11 ms before starting any programming on the MIIM.
Counting that, add a 200 ms delay to be sure the PHY is ready for
programming. Also, add the same off delay time to give the capacitor
time to discharge in order to properly reset.
ARM: dts: imx7-colibri: improve wake-up with gpio key
The pin GPIO1_IO01 externally pulls down, it is required to sequentially
connect this pin (signal WAKE_MICO#) to +3v3 and then disconnect it to
trigger a wakeup interrupt.
Adding the flag GPIO_PULL_DOWN allows the system to be woken up just
connecting the pin GPIO1_IO01 to +3v3.
Rename display interface to match other modules to make it easier to
use device tree overlays.
The parallel RGB interface (lcdif) and all related stuff turn on in a
device tree overlay. Keep them disabled in the main devicetree.
As these subsystems are provided by module and not a part of boards,
move their definitions into the module-level devicetree.
Disable ad7879 touchscreen which turns on in a devic tree overlay.
Remains it disabled in the main devicetree.
Move Atmel MXT capacitive touch controller device tree nodes from
carrier board to module level and add iomux pinctl groups for both the
Capacitive Touch Adapter (using SODIMM 28/30) and the capacitive touch
connector as found on later carrier boards (using SODIMM 106/107).
Keep touchscreen and display nodes enabled for NAND based i.MX 7
modules, since device tree overlays are not yet supported. For the
Colibri Evaluation Board keep the Capacitive Touch Adapter node
disabled and PWM2, PWM3 enabled instead.
For eMMC based modules keep nodes disabled to work in conjunction with
device tree overlays.
Add the iomuxc pinctrl group for the LVDS transceiver related signals to
use it in a device tree overlay.
While at it also alphabetically re=order them properties.
Set #pwm-cells to the default 3 to gain access to the parameter
which allows inverting the PWM signal. This is useful to specify
a backlight which has its highest brightness at 0.
With the change to use the PWM with inverted polarity the PWM signal
is inverted to how it was before this patch.
This changes the meaning of the values in the brightness-levels
property. I.e. the duty-cycle changes from x/255 to (255-x)/255.
Keeping the brightness-levels will then have a big brightness
jump from 0 to 127 duty cycle, the other 6 steps will then be
barely noticeable.
Change the brightness-levels to provide the same brightness-levels
as before.
Yinjun Zhang [Thu, 9 Jun 2022 08:01:36 +0000 (10:01 +0200)]
nfp: flower: support to offload pedit of IPv6 flowinto fields
Previously the traffic class field is ignored while firmware has
already supported to pedit flowinfo fields, including traffic
class and flow label, now add it back.
Bin Chen [Thu, 9 Jun 2022 08:47:17 +0000 (10:47 +0200)]
ethernet: Remove vf rate limit check for drivers
The commit a14857c27a50 ("rtnetlink: verify rate parameters for calls to
ndo_set_vf_rate") has been merged to master, so we can to remove the
now-duplicate checks in drivers.
====================
Documentation: add description for a couple of sctp sysctl options
These are a couple of sysctl options I recently added, but missed adding
documents for them. Especially for net.sctp.intl_enable, it's hard for
users to setup stream interleaving, as it also needs to call some socket
options.
This patchset is to add documents for them.
====================
Xin Long [Thu, 9 Jun 2022 15:17:15 +0000 (11:17 -0400)]
Documentation: add description for net.sctp.ecn_enable
Describe it in networking/ip-sysctl.rst like other SCTP options.
Fixes: 2f5268a9249b ("sctp: allow users to set netns ecn flag with sysctl") Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Xin Long [Thu, 9 Jun 2022 15:17:14 +0000 (11:17 -0400)]
Documentation: add description for net.sctp.intl_enable
Describe it in networking/ip-sysctl.rst like other SCTP options.
We need to document this especially as when using the feature
of User Message Interleaving, some socket options also needs
to be set.
Fixes: 463118c34a35 ("sctp: support sysctl to allow users to use stream interleave") Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Xin Long [Thu, 9 Jun 2022 15:17:13 +0000 (11:17 -0400)]
Documentation: add description for net.sctp.reconf_enable
Describe it in networking/ip-sysctl.rst like other SCTP options.
Fixes: c0d8bab6ae51 ("sctp: add get and set sockopt for reconf_enable") Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Sat, 11 Jun 2022 05:10:30 +0000 (22:10 -0700)]
Merge branch '40GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2022-06-09
Grzegorz prevents addition of TC flower filters to TC0 and fixes queue
iteration for VF ADQ to number of actual queues for i40e.
Aleksandr prevents running of ethtool tests when device is being reset
for i40e.
Michal resolves an issue where iavf does not report its MAC address
properly.
* '40GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
iavf: Fix issue with MAC address of VF shown as zero
i40e: Fix call trace in setup_tx_descriptors
i40e: Fix calculating the number of queue pairs
i40e: Fix adding ADQ filter to TC0
====================
Call virtio_device_ready() to make this driver work after commit b4ec69d7e09 ("virtio: harden vring IRQ"), since the driver uses the
virtqueues in the probe function. (The virtio core sets the device
ready when probe returns.)
Fixes: 8b4ec69d7e09 ("virtio: harden vring IRQ") Fixes: 68f5d3f3b654 ("um: add PCI over virtio emulation driver") Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Message-Id: <20220610151203.3492541-1-vincent.whitchurch@axis.com> Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Tested-by: Johannes Berg <johannes@sipsolutions.net>
Linus Torvalds [Sat, 11 Jun 2022 00:28:43 +0000 (17:28 -0700)]
Merge tag 'nfsd-5.19-1' of git://git.kernel.org/pub/scm/linux/kernel/git/cel/linux
Pull nfsd fixes from Chuck Lever:
"Notable changes:
- There is now a backup maintainer for NFSD
Notable fixes:
- Prevent array overruns in svc_rdma_build_writes()
- Prevent buffer overruns when encoding NFSv3 READDIR results
- Fix a potential UAF in nfsd_file_put()"
* tag 'nfsd-5.19-1' of git://git.kernel.org/pub/scm/linux/kernel/git/cel/linux:
SUNRPC: Remove pointer type casts from xdr_get_next_encode_buffer()
SUNRPC: Clean up xdr_get_next_encode_buffer()
SUNRPC: Clean up xdr_commit_encode()
SUNRPC: Optimize xdr_reserve_space()
SUNRPC: Fix the calculation of xdr->end in xdr_get_next_encode_buffer()
SUNRPC: Trap RDMA segment overflows
NFSD: Fix potential use-after-free in nfsd_file_put()
MAINTAINERS: reciprocal co-maintainership for file locking and nfsd
Shyam Prasad N [Mon, 6 Jun 2022 09:52:46 +0000 (09:52 +0000)]
cifs: populate empty hostnames for extra channels
Currently, the secondary channels of a multichannel session
also get hostname populated based on the info in primary channel.
However, this will end up with a wrong resolution of hostname to
IP address during reconnect.
This change fixes this by not populating hostname info for all
secondary channels.
Fixes: 5112d80c162f ("cifs: populate server_hostname for extra channels") Cc: stable@vger.kernel.org Signed-off-by: Shyam Prasad N <sprasad@microsoft.com> Signed-off-by: Steve French <stfrench@microsoft.com>
Linus Torvalds [Fri, 10 Jun 2022 23:32:49 +0000 (16:32 -0700)]
Merge tag 'for-5.19/dm-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper fixes from Mike Snitzer:
- Fix DM core's bioset initialization so that blk integrity pool is
properly setup. Remove now unused bioset_init_from_src.
- Fix DM zoned hang from locking imbalance due to needless check in
clone_endio().
* tag 'for-5.19/dm-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm: fix zoned locking imbalance due to needless check in clone_endio
block: remove bioset_init_from_src
dm: fix bio_set allocation
Hosts with a lot of sockets tend to hit so called TCP memory pressure,
leading to very bad TCP performance and/or OOM.
The problem is that some TCP sockets can hold up to 2MB of 'forward
allocations' in their per-socket cache (sk->sk_forward_alloc),
and there is no mechanism to make them relinquish their share
under mem pressure.
Only under some potentially rare events their share is reclaimed,
one socket at a time.
In this series, I implemented a per-cpu cache instead of a per-socket one.
Each CPU has a +1/-1 MB (256 pages on x86) forward alloc cache, in order
to not dirty tcp_memory_allocated shared cache line too often.
We keep sk->sk_forward_alloc values as small as possible, to meet
memcg page granularity constraint.
Note that memcg already has a per-cpu cache, although MEMCG_CHARGE_BATCH
is defined to 32 pages, which seems a bit small.
Note that while this cover letter mentions TCP, this work is generic
and supports TCP, UDP, DECNET, SCTP.
====================
Eric Dumazet [Thu, 9 Jun 2022 06:34:11 +0000 (23:34 -0700)]
net: keep sk->sk_forward_alloc as small as possible
Currently, tcp_memory_allocated can hit tcp_mem[] limits quite fast.
Each TCP socket can forward allocate up to 2 MB of memory, even after
flow became less active.
10,000 sockets can have reserved 20 GB of memory,
and we have no shrinker in place to reclaim that.
Instead of trying to reclaim the extra allocations in some places,
just keep sk->sk_forward_alloc values as small as possible.
This should not impact performance too much now we have per-cpu
reserves: Changes to tcp_memory_allocated should not be too frequent.
For sockets not using SO_RESERVE_MEM:
- idle sockets (no packets in tx/rx queues) have zero forward alloc.
- non idle sockets have a forward alloc smaller than one page.
Note:
- Removal of SK_RECLAIM_CHUNK and SK_RECLAIM_THRESHOLD
is left to MPTCP maintainers as a follow up.
Signed-off-by: Eric Dumazet <edumazet@google.com> Reviewed-by: Shakeel Butt <shakeelb@google.com> Acked-by: Soheil Hassas Yeganeh <soheil@google.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Eric Dumazet [Thu, 9 Jun 2022 06:34:10 +0000 (23:34 -0700)]
net: fix sk_wmem_schedule() and sk_rmem_schedule() errors
If sk->sk_forward_alloc is 150000, and we need to schedule 150001 bytes,
we want to allocate 1 byte more (rounded up to one page),
instead of 150001 :/
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Eric Dumazet <edumazet@google.com> Reviewed-by: Shakeel Butt <shakeelb@google.com> Acked-by: Soheil Hassas Yeganeh <soheil@google.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Linus Torvalds [Fri, 10 Jun 2022 23:15:19 +0000 (16:15 -0700)]
Merge branch 'fscache-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs
Pull fscache cleanups from David Howells:
- fix checker complaint in afs
- two netfs cleanups:
- netfs_inode calling convention cleanup plus the requisite
documentation changes
- replace the ->cleanup op with a ->free_request op.
This is possible as the I/O request is now always available at
the cleanup point as the stuff to be cleaned up is no longer
passed into the API functions, but rather obtained by ->init_request.
* 'fscache-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs:
netfs: Rename the netfs_io_request cleanup op and give it an op pointer
netfs: Further cleanups after struct netfs_inode wrapper introduced
afs: Fix some checker issues
Al Viro [Sun, 22 May 2022 15:38:11 +0000 (11:38 -0400)]
keep iocb_flags() result cached in struct file
* calculate at the time we set FMODE_OPENED (do_dentry_open() for normal
opens, alloc_file() for pipe()/socket()/etc.)
* update when handling F_SETFL
* keep in a new field - file->f_iocb_flags; since that thing is needed only
before the refcount reaches zero, we can put it into the same anon union
where ->f_rcuhead and ->f_llist live - those are used only after refcount
reaches zero.
Reviewed-by: Christian Brauner (Microsoft) <brauner@kernel.org> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Al Viro [Sun, 22 May 2022 13:39:27 +0000 (09:39 -0400)]
iocb: delay evaluation of IS_SYNC(...) until we want to check IOCB_DSYNC
New helper to be used instead of direct checks for IOCB_DSYNC:
iocb_is_dsync(iocb). Checks converted, which allows to avoid
the IS_SYNC(iocb->ki_filp->f_mapping->host) part (4 cache lines)
from iocb_flags() - it's checked in iocb_is_dsync() instead
Reviewed-by: Christian Brauner (Microsoft) <brauner@kernel.org> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Al Viro [Tue, 7 Jun 2022 20:10:01 +0000 (16:10 -0400)]
btrfs: use IOMAP_DIO_NOSYNC
... instead of messing with iocb flags
Suggested-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Christian Brauner (Microsoft) <brauner@kernel.org> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Al Viro [Tue, 7 Jun 2022 20:04:03 +0000 (16:04 -0400)]
teach iomap_dio_rw() to suppress dsync
New flag, equivalent to removal of IOCB_DSYNC from iocb flags.
This mimics what btrfs is doing (and that's what btrfs will
switch to). However, I'm not at all sure that we want to
suppress REQ_FUA for those - all btrfs hack really cares about
is suppression of generic_write_sync(). For now let's keep
the existing behaviour, but I really want to hear more detailed
arguments pro or contra.
[folded brain fix from willy]
Suggested-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Christian Brauner (Microsoft) <brauner@kernel.org> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Jiasheng Jiang [Thu, 26 May 2022 09:03:45 +0000 (17:03 +0800)]
platform/x86: barco-p50-gpio: Add check for platform_driver_register
As platform_driver_register() could fail, it should be better
to deal with the return value in order to maintain the code
consisitency.
Fixes: 86af1d02d458 ("platform/x86: Support for EC-connected GPIOs for identify LED/button on Barco P50 board") Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn> Acked-by: Peter Korsgaard <peter.korsgaard@barco.com> Link: https://lore.kernel.org/r/20220526090345.1444172-1-jiasheng@iscas.ac.cn Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The probe function pmt_crashlog_probe() may incorrectly reference
the 'priv->entry array' as it uses 'i' to reference the array instead
of 'priv->num_entries' as it should. This is similar to the problem
that was addressed in pmt_telemetry_probe via commit 2cdfa0c20d58
("platform/x86/intel: Fix 'rmmod pmt_telemetry' panic").
Cc: "David E. Box" <david.e.box@linux.intel.com> Cc: Hans de Goede <hdegoede@redhat.com> Cc: Mark Gross <markgross@kernel.org> Cc: linux-kernel@vger.kernel.org Signed-off-by: David Arcari <darcari@redhat.com> Reviewed-by: David E. Box <david.e.box@linux.intel.com> Link: https://lore.kernel.org/r/20220526203140.339120-1-darcari@redhat.com Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Michael Shych [Thu, 2 Jun 2022 14:51:03 +0000 (17:51 +0300)]
platform/mellanox: Add static in struct declaration.
Fix problem of missing static in struct declaration.
Fixes: 662f24826f954 ("platform/mellanox: Add support for new SN2201 system") Reported-by: kernel test robot <lkp@intel.com> Signed-off-by: Michael Shych <michaelsh@nvidia.com> Link: https://lore.kernel.org/r/20220602145103.11859-1-michaelsh@nvidia.com Signed-off-by: Hans de Goede <hdegoede@redhat.com>
David Howells [Thu, 9 Jun 2022 08:07:01 +0000 (09:07 +0100)]
iov_iter: Fix iter_xarray_get_pages{,_alloc}()
The maths at the end of iter_xarray_get_pages() to calculate the actual
size doesn't work under some circumstances, such as when it's been asked to
extract a partial single page. Various terms of the equation cancel out
and you end up with actual == offset. The same issue exists in
iter_xarray_get_pages_alloc().
Fix these to just use min() to select the lesser amount from between the
amount of page content transcribed into the buffer, minus the offset, and
the size limit specified.
This doesn't appear to have caused a problem yet upstream because network
filesystems aren't getting the pages from an xarray iterator, but rather
passing it directly to the socket, which just iterates over it. Cachefiles
*does* do DIO from one to/from ext4/xfs/btrfs/etc. but it always asks for
whole pages to be written or read.
Fixes: 7ff5062079ef ("iov_iter: Add ITER_XARRAY") Reported-by: Jeff Layton <jlayton@kernel.org> Signed-off-by: David Howells <dhowells@redhat.com>
cc: Alexander Viro <viro@zeniv.linux.org.uk>
cc: Dominique Martinet <asmadeus@codewreck.org>
cc: Mike Marshall <hubcap@omnibond.com>
cc: Gao Xiang <xiang@kernel.org>
cc: linux-afs@lists.infradead.org
cc: v9fs-developer@lists.sourceforge.net
cc: devel@lists.orangefs.org
cc: linux-erofs@lists.ozlabs.org
cc: linux-cachefs@redhat.com
cc: linux-fsdevel@vger.kernel.org Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
David Howells [Fri, 25 Feb 2022 11:19:14 +0000 (11:19 +0000)]
netfs: Rename the netfs_io_request cleanup op and give it an op pointer
The netfs_io_request cleanup op is now always in a position to be given a
pointer to a netfs_io_request struct, so this can be passed in instead of
the mapping and private data arguments (both of which are included in the
struct).
So rename the ->cleanup op to ->free_request (to match ->init_request) and
pass in the I/O pointer.
Signed-off-by: David Howells <dhowells@redhat.com> Reviewed-by: Jeff Layton <jlayton@kernel.org>
cc: linux-cachefs@redhat.com
Linus Torvalds [Thu, 9 Jun 2022 22:04:01 +0000 (15:04 -0700)]
netfs: Further cleanups after struct netfs_inode wrapper introduced
Change the signature of netfs helper functions to take a struct netfs_inode
pointer rather than a struct inode pointer where appropriate, thereby
relieving the need for the network filesystem to convert its internal inode
format down to the VFS inode only for netfslib to bounce it back up. For
type safety, it's better not to do that (and it's less typing too).
Give netfs_write_begin() an extra argument to pass in a pointer to the
netfs_inode struct rather than deriving it internally from the file
pointer. Note that the ->write_begin() and ->write_end() ops are intended
to be replaced in the future by netfslib code that manages this without the
need to call in twice for each page.
netfs_readpage() and similar are intended to be pointed at directly by the
address_space_operations table, so must stick to the signature dictated by
the function pointers there.
Changes
=======
- Updated the kerneldoc comments and documentation [DH].
Linus Torvalds [Fri, 10 Jun 2022 19:41:48 +0000 (12:41 -0700)]
Merge tag 'folio-5.19a' of git://git.infradead.org/users/willy/pagecache
Pull folio fixes from Matthew Wilcox:
"Four folio-related fixes:
- Don't release a folio while it's still locked
- Fix a use-after-free after dropping the mmap_lock
- Fix a memory leak when splitting a page
- Fix a kernel-doc warning for struct folio"
* tag 'folio-5.19a' of git://git.infradead.org/users/willy/pagecache:
mm: Add kernel-doc for folio->mlock_count
mm/huge_memory: Fix xarray node memory leak
filemap: Cache the value of vm_flags
filemap: Don't release a locked folio
Kenneth Feng [Wed, 1 Jun 2022 01:20:28 +0000 (09:20 +0800)]
drm/amd/pm: support BAMACO reset on smu_v13_0_7
support BAMACO reset on smu_v13_0_7, take BAMACO as a subset of BACO
for the low latency, and it only happens on specific platforms.
Signed-off-by: Kenneth Feng <kenneth.feng@amd.com> Reviewed-by: Yang Wang <kevinyang.wang@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Kenneth Feng [Wed, 8 Jun 2022 08:59:52 +0000 (16:59 +0800)]
drm/amd/pm: enable gfxoff on smu_v13_0_7
enable gfxoff on smu_v13_0_7
Signed-off-by: Kenneth Feng <kenneth.feng@amd.com> Reviewed-by: Yang Wang <kevinyang.wang@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Kenneth Feng [Wed, 8 Jun 2022 08:40:14 +0000 (16:40 +0800)]
drm/amd/pm: update the driver if header for smu_v13_0_7
update the driver if header for smu_v13_0_7
Signed-off-by: Kenneth Feng <kenneth.feng@amd.com> Reviewed-by: Yang Wang <kevinyang.wang@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
drm/amdgpu: Stop any pending reset if another in progress.
We skip rest requests if another one is already in progress.
Signed-off-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
drm/amdgpu: Rename amdgpu_device_gpu_recover_imp back to amdgpu_device_gpu_recover
We removed the wrapper that was queueing the recover function
into reset domain queue who was using this name.
Signed-off-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
drm/amdgpu: Add work_struct for GPU reset from kfd.
We need to have a work_struct to cancel this reset if another
already in progress.
Signed-off-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
drm/amdgpu: Add work_struct for GPU reset from debugfs
We need to have a work_struct to cancel this reset if another
already in progress.
Signed-off-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
drm/admgpu: Serialize RAS recovery work directly into reset domain queue.
Save the extra usless work schedule.
Signed-off-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com> Acked-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
drm/amdgpu: Cache result of last reset at reset domain level.
Will be read by executors of async reset like debugfs.
Signed-off-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
amdpgu need this function in order to prematurly stop pending
reset works when another reset work already in progress.
Acked-by: Tejun Heo <tj@kernel.org> Signed-off-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com> Reviewed-by: Lai Jiangshan<jiangshanlai@gmail.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser2.c:3276:20: error: variable 'v1_5' is uninitialized when used here [-Werror,-Wuninitialized]
for (i = 0; i < v1_5->number_of_path; ++i)
^~~~
[How]
Fix compilation issues
Signed-off-by: Chandan Vurdigere Nataraj <chandan.vurdigerenataraj@amd.com> Reviewed-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
drm/amdgpu/display: Remove unnecessary typecasts and fix build issues
[Why]
Getting below errors:
drivers/gpu/drm/amd/amdgpu/../display/dc/dml/dcn32/display_mode_vba_32.c:1414:5: error: implicit conversion from enumeration type 'enum scan_direction_class' to different enumeration type 'enum dm_rotation_angle' [-Werror,-Wenum-conversion]
mode_lib->vba.SourceScan[k],
^~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/gpu/drm/amd/amdgpu/../display/dc/dml/dcn32/display_mode_vba_32.c:1744:22: error: implicit conversion from enumeration type 'enum scan_direction_class' to different enumeration type 'enum dm_rotation_angle' [-Werror,-Wenum-conversion]
&& (!(!IsVertical(mode_lib->vba.SourceScan[k])) || mode_lib->vba.DCCEnable[k] == true)) {
~~~~~~~~~~ ^~~~~~~~~~~~~~~~~~~~~~~~~~~
2 errors generated.
drivers/gpu/drm/amd/amdgpu/../display/dc/dml/dcn32/display_mode_vba_util_32.c:5484:18: error: implicit conversion from enumeration type 'RequestType' to different enumeration type 'enum RequestType' [-Werror,-Wenum-conversion]
RequestLuma = REQ_256Bytes;
~ ^~~~~~~~~~~~
18 errors of similar kind
[How]
1. Add typecast at relevant places
2. Move the enum RequestType definition ahead of declarations
Signed-off-by: Chandan Vurdigere Nataraj <chandan.vurdigerenataraj@amd.com> Reviewed-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Mike Snitzer [Fri, 10 Jun 2022 19:07:48 +0000 (15:07 -0400)]
dm: fix zoned locking imbalance due to needless check in clone_endio
After the commit ca522482e3ea ("dm: pass NULL bdev to bio_alloc_clone"),
clone_endio() only calls dm_zone_endio() when DM targets remap the
clone bio's bdev to something other than the md->disk->part0 default.
However, if a DM target (e.g. dm-crypt) stacked ontop of a dm-zoned
does not remap the clone bio using bio_set_dev() then dm_zone_endio()
is not called at completion of the bios and zone locks are not
properly unlocked. This triggers a hang, in dm_zone_map_bio(), when
blktests block/004 is run for dm-crypt on zoned block devices. To
avoid the hang, simply remove the clone_endio() check that verifies
the target remapped the clone bio to a device other than the default.
Fixes: ca522482e3ea ("dm: pass NULL bdev to bio_alloc_clone") Reported-by: Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com> Signed-off-by: Mike Snitzer <snitzer@kernel.org>
Linus Torvalds [Fri, 10 Jun 2022 18:49:27 +0000 (11:49 -0700)]
Merge tag 'pm-5.19-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"These fix an intel_idle issue introduced during the 5.16 development
cycle and two recent regressions in the system reboot/poweroff code.
Specifics:
- Fix CPUIDLE_FLAG_IRQ_ENABLE handling in intel_idle (Peter Zijlstra)
- Allow all platforms to use the global poweroff handler and make
non-syscall poweroff code paths work again (Dmitry Osipenko)"
* tag 'pm-5.19-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpuidle,intel_idle: Fix CPUIDLE_FLAG_IRQ_ENABLE
kernel/reboot: Fix powering off using a non-syscall code paths
kernel/reboot: Use static handler for register_platform_power_off()
As Liviu pointed out, the arm,malidp-arqos-high-level property
mentioned in the original .txt binding was a mistake, and
arm,malidp-arqos-value needs to take its place.
The binding commit ce6eb0253cba ("dt/bindings: display: Add optional
property node define for Mali DP500") mentions the right name in the
commit message, but has the wrong name in the diff.
Commit d298e6a27a81 ("drm/arm/mali-dp: Add display QoS interface
configuration for Mali DP500") uses the property in the driver, but uses
the shorter name.
Remove the wrong property from the binding, and use the proper name in
the example. The actual property was already documented properly.
Rob Herring [Mon, 6 Jun 2022 21:22:39 +0000 (16:22 -0500)]
dt-bindings: pinctrl: ralink: Fix 'enum' lists with duplicate entries
There's no reason to list the same value twice in an 'enum'. This was fixed
treewide in commit c3b006819426 ("dt-bindings: Fix 'enum' lists with
duplicate entries"), but this one got added in the merge window.
Linus Torvalds [Fri, 10 Jun 2022 18:14:47 +0000 (11:14 -0700)]
Merge tag 'docs-5.19-3' of git://git.lwn.net/linux
Pull documentation fixes from Jonathan Corbet:
"A few documentation fixes for 5.19, including moving the new HTE docs
to a more suitable location, adding loongarch to the features lists,
and a couple of typo fixes"
* tag 'docs-5.19-3' of git://git.lwn.net/linux:
docs: arm: tcm: Fix typo in description of TCM and MMU usage
docs: Move the HTE documentation to driver-api/
docs: usb: fix literal block marker in usbmon verification example
Documentation/features: Update the arch support status files
- Some typos in documentation or comments and silence a sparse warning
(missing prototype).
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: Add kasan_hw_tags_enable() prototype to silence sparse
arm64/sme: Fix EFI save/restore
arm64/fpsimd: Fix typo in comment
arm64/sysreg: Fix typo in Enum element regex
arm64/sme: Fix SVE/SME typo in ABI documentation
arm64/sme: Fix tests for 0b1111 value ID registers
Linus Torvalds [Fri, 10 Jun 2022 17:56:28 +0000 (10:56 -0700)]
Merge tag 'zonefs-5.19-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/zonefs
Pull zonefs fixes from Damien Le Moal:
- Fix handling of the explicit-open mount option, and in particular the
conditions under which this option can be ignored.
- Fix a problem with zonefs iomap_begin method, causing a hang in
iomap_readahead() when a readahead request reaches the end of a file.
* tag 'zonefs-5.19-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/zonefs:
zonefs: fix zonefs_iomap_begin() for reads
zonefs: Do not ignore explicit_open with active zone limit
zonefs: fix handling of explicit_open option on mount
Mark Brown [Fri, 10 Jun 2022 17:28:20 +0000 (18:28 +0100)]
ASoC: SOF: Add support ctx_save with IPC4
Merge series from Peter Ujfalusi <peter.ujfalusi@linux.intel.com>:
The context save functionality with IPC4 is triggered by sending a message to
the firmware about the pending power down of the primary core by the host.
In order to have this functionality implemented in a clean way we need to
introduce a new IPC level PM ops for core state management and use that instead
of open coding IPC messages here and there.
The first patch updates the ctx store/ctx_restore documentation to clarify that
they are optional.
Linus Torvalds [Fri, 10 Jun 2022 17:20:57 +0000 (10:20 -0700)]
Merge tag 'sound-5.19-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"A collection of fixes; almost all changes are device-specific small
fixes over ASoC, HD-audio and USB-audio. No sign of serious breakage,
so far"
* tag 'sound-5.19-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (23 commits)
ALSA: hda/realtek: Add quirk for HP Dev One
ALSA: hda/realtek - Add HW8326 support
ALSA: hda/conexant - Fix loopback issue with CX20632
ALSA: hda: MTL: add HD Audio PCI ID and HDMI codec vendor ID
ALSA: usb-audio: Set up (implicit) sync for Saffire 6
ALSA: usb-audio: Skip generic sync EP parse for secondary EP
ASoC: wm_adsp: Fix event generation for wm_adsp_fw_put()
ASoC: es8328: Fix event generation for deemphasis control
ASoC: wm8962: Fix suspend while playing music
ASoC: SOF: ipc-msg-injector: Fix reversed if statement
ASoC: SOF: ipc-msg-injector: Propagate write errors correctly
ASoC: fsl_sai: Add support for i.MX8MN
ASoC: SOF: Fix potential NULL pointer dereference
ALSA: hda/realtek: Fix for quirk to enable speaker output on the Lenovo Yoga DuetITL 2021
ASoC: cs42l51: Correct minimum value for SX volume control
ASoC: cs42l56: Correct typo in minimum level for SX volume controls
ASoC: cs42l52: Correct TLV for Bypass Volume
ASoC: cs53l30: Correct number of volume levels on SX controls
ASoC: cs35l36: Update digital volume TLV
ASoC: cs42l52: Fix TLV scales for mixer controls
...
Linus Torvalds [Fri, 10 Jun 2022 17:13:24 +0000 (10:13 -0700)]
Merge tag 'drm-fixes-2022-06-10' of git://anongit.freedesktop.org/drm/drm
Pull drm fixes from Dave Airlie:
"Not a huge amount here, mainly a bunch of scattered amdgpu fixes, and
then some misc panfrost, bridge/panel ones, and one ast fix for
multi-monitors. Probably pick up a bit more next week like rc3 often
does.
amdkfd:
- MMU notifier fix
- Support for more GC 10.3.x families
- Pinned BO handling fix
- Partial migration bug fix
panfrost:
- fix a use after free
ti-sn65dsi83:
- fix invalid DT configuration
panel:
- two self refresh fixes
ast:
- multiple output fix"
* tag 'drm-fixes-2022-06-10' of git://anongit.freedesktop.org/drm/drm: (37 commits)
drm/ast: Support multiple outputs
drm/amdgpu/mes: only invalid/prime icache when finish loading both pipe MES FWs.
drm/amdgpu/jpeg2: Add jpeg vmid update under IB submit
drm/amdgpu: always flush the TLB on gfx8
drm/amdgpu: fix limiting AV1 to the first instance on VCN3
drm/amdkfd:Fix fw version for 10.3.6
drm/amdgpu: Add MODE register to wave debug info in gfx11
Revert "drm/amd/display: Pass the new context into disable OTG WA"
Revert "drm/amdgpu: Ensure the DMA engine is deactivated during set ups"
drm/atomic: Force bridge self-refresh-exit on CRTC switch
drm/bridge: analogix_dp: Support PSR-exit to disable transition
drm/amdgpu: suppress the compile warning about 64 bit type
drm/amd/pm: suppress compile warnings about possible unaligned accesses
drm/amdkfd: Fix partial migration bugs
drm/amdkfd: add pinned BOs to kfd_bo_list
drm/amdgpu: Update PDEs flush TLB if PTB/PDB moved
drm/amdgpu: enable tmz by default for GC 10.3.7
drm/amdkfd: Add GC 10.3.6 and 10.3.7 KFD definitions
drm/amdkfd: Use mmget_not_zero in MMU notifier
drm/amdgpu: Resolve RAS GFX error count issue after cold boot on Arcturus
...
Damien Le Moal [Thu, 9 Jun 2022 02:24:56 +0000 (11:24 +0900)]
scsi: libsas: Introduce struct smp_rps_resp
Similarly to sas report general and discovery responses, define the
structure struct smp_rps_resp to handle SATA PHY report responses using a
structure with a size that is exactly equal to the sas defined response
size.
With this change, struct smp_resp becomes unused and is removed.
Damien Le Moal [Thu, 9 Jun 2022 02:24:55 +0000 (11:24 +0900)]
scsi: libsas: Introduce struct smp_rg_resp
When compiling with gcc 12, several warnings are thrown by gcc when
compiling drivers/scsi/libsas/sas_expander.c, e.g.:
In function ‘sas_get_ex_change_count’,
inlined from ‘sas_find_bcast_dev’ at
drivers/scsi/libsas/sas_expander.c:1816:8:
drivers/scsi/libsas/sas_expander.c:1781:20: warning: array subscript
‘struct smp_resp[0]’ is partly outside array bounds of ‘unsigned
char[32]’ [-Warray-bounds]
1781 | if (rg_resp->result != SMP_RESP_FUNC_ACC) {
| ~~~~~~~^~~~~~~~
This is due to the use of the struct smp_resp to aggregate all possible
response types using a union but allocating a response buffer with a size
exactly equal to the size of the response type needed. This leads to access
to fields of struct smp_resp from an allocated memory area that is smaller
than the size of struct smp_resp.
Fix this by defining struct smp_rg_resp for sas report general responses.
Damien Le Moal [Thu, 9 Jun 2022 02:24:54 +0000 (11:24 +0900)]
scsi: libsas: Introduce struct smp_disc_resp
When compiling with gcc 12, several warnings are thrown by gcc when
compiling drivers/scsi/libsas/sas_expander.c, e.g.:
In function ‘sas_get_phy_change_count’,
inlined from ‘sas_find_bcast_phy.constprop’ at
drivers/scsi/libsas/sas_expander.c:1737:9:
drivers/scsi/libsas/sas_expander.c:1697:39: warning: array subscript
‘struct smp_resp[0]’ is partly outside array bounds of ‘unsigned
char[56]’ [-Warray-bounds]
1697 | *pcc = disc_resp->disc.change_count;
| ~~~~~~~~~~~~~~~^~~~~~~~~~~~~
This is due to the use of the struct smp_resp to aggregate all possible
response types using a union but allocating a response buffer with a size
exactly equal to the size of the response type needed. This leads to access
to fields of struct smp_resp from an allocated memory area that is smaller
than the size of struct smp_resp.
Fix this by defining struct smp_disc_resp for sas discovery operations.
Since this structure and the generic struct smp_resp are identical for
the little endian and big endian archs, move the definition of these
structures at the end of include/scsi/sas.h to avoid repeating their
definition.
Linus Torvalds [Fri, 10 Jun 2022 17:07:06 +0000 (10:07 -0700)]
Merge tag 'net-5.19-rc2-2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Quick follow up, to cleanly fast-forward net again.
Current release - new code bugs:
- Revert "net/mlx5e: Allow relaxed ordering over VFs"
Previous releases - regressions:
- seg6: fix seg6_lookup_any_nexthop() to handle VRFs using
flowi_l3mdev
Misc:
- rename TLS_INFO_ZC_SENDFILE to better express the meaning"
* tag 'net-5.19-rc2-2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net:
net: seg6: fix seg6_lookup_any_nexthop() to handle VRFs using flowi_l3mdev
nfp: flower: restructure flow-key for gre+vlan combination
nfp: avoid unnecessary check warnings in nfp_app_get_vf_config
tls: Rename TLS_INFO_ZC_SENDFILE to TLS_INFO_ZC_TX
net/mlx5: fs, fail conflicting actions
net/mlx5: Rearm the FW tracer after each tracer event
net/mlx5: E-Switch, pair only capable devices
net/mlx5e: CT: Fix cleanup of CT before cleanup of TC ct rules
Revert "net/mlx5e: Allow relaxed ordering over VFs"
MAINTAINERS: adjust MELLANOX ETHERNET INNOVA DRIVERS to TLS support removal
Catalin Marinas [Fri, 10 Jun 2022 17:01:31 +0000 (18:01 +0100)]
arm64: Add kasan_hw_tags_enable() prototype to silence sparse
This function is only called from assembly, no need for a prototype
declaration in a header file. In addition, add #ifdef around the
function since it is only used when CONFIG_KASAN_HW_TAGS.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Reported-by: kernel test robot <lkp@intel.com>
Quinn Tran [Wed, 8 Jun 2022 11:58:48 +0000 (04:58 -0700)]
scsi: qla2xxx: edif: Fix slow session teardown
User experience slow recovery when target device went through a stop/start
of the authentication application (app_stop/app_start).
Between the period of app_stop and app_start on the target device, target
device choose to send ELS Reject for any receive AUTH ELS command. At this
time, authentication application does not do ELS reject if it encounters
error.
Therefore, AUTH ELS reject signify authentication application is not
running. If driver passes up the AUTH ELS Reject to the authentication
application, then it would result in authentication application
retrying/resending the same AUTH ELS command again + delay.
As a work around, driver should trigger a session tear down where it tells
the local authentication application to also tear down. At the next
relogin, both sides are then synchronized.
Link: https://lore.kernel.org/r/20220608115849.16693-10-njavali@marvell.com Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com> Signed-off-by: Quinn Tran <qutran@marvell.com> Signed-off-by: Nilesh Javali <njavali@marvell.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Quinn Tran [Wed, 8 Jun 2022 11:58:47 +0000 (04:58 -0700)]
scsi: qla2xxx: edif: Reduce N2N thrashing at app_start time
For N2N + remote WWPN is bigger than local adapter, remote adapter will
login to local adapter while authentication application is not running.
When authentication application starts, the current session in FW needs to
to be invalidated.
Make sure the old session is torn down before triggering a relogin.
Link: https://lore.kernel.org/r/20220608115849.16693-9-njavali@marvell.com Fixes: 4de067e5df12 ("scsi: qla2xxx: edif: Add N2N support for EDIF") Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com> Signed-off-by: Quinn Tran <qutran@marvell.com> Signed-off-by: Nilesh Javali <njavali@marvell.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
projects / people / ms / linux.git / log
