media: i2c: video-i2c: Move defines to the top of the file
Currently, the defines in this driver are after some structs and
functions, it makes more sense to move them up to the top of the file,
so that the constants can be named together with other defines.
Signed-off-by: Moses Christopher Bollavarapu <mosescb.dev@gmail.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Sakari Ailus [Tue, 26 Apr 2022 07:02:39 +0000 (09:02 +0200)]
media: Add CSI-2 bus configuration to frame descriptors
Add CSI-2 bus specific configuration to the frame descriptors. This allows
obtaining the virtual channel and data type information for each stream
the transmitter is sending.
Dongliang Mu [Fri, 22 Apr 2022 08:54:05 +0000 (10:54 +0200)]
media: ov7670: remove ov7670_power_off from ov7670_remove
In ov7670_probe, it always invokes ov7670_power_off() no matter
the execution is successful or failed. So we cannot invoke it
agiain in ov7670_remove().
Fix this by removing ov7670_power_off from ov7670_remove.
Fixes: 030f9f682e66 ("media: ov7670: control clock along with power") Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
There is firmware out there that uses "dongwoon,dw9807" compatible string
that never made it to upstream as-is. Add it to the driver to make it load
on such systems.
The chip also has an EEPROM part which is AT24 compatible (for reading
purposes) on a separate I²C address. Adding possible support for this in
the future is not affected by this change.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The imx412/imx577 sensor has a reset line that is active low not active
high. Currently the logic for this is inverted.
The right way to define the reset line is to declare it active low in the
DTS and invert the logic currently contained in the driver.
The DTS should represent the hardware does i.e. reset is active low.
So:
+ reset-gpios = <&tlmm 78 GPIO_ACTIVE_LOW>;
not:
- reset-gpios = <&tlmm 78 GPIO_ACTIVE_HIGH>;
I was a bit reticent about changing this logic since I thought it might
negatively impact @intel.com users. Googling a bit though I believe this
sensor is used on "Keem Bay" which is clearly a DTS based system and is not
upstream yet.
Stefan Wahren [Thu, 28 Apr 2022 18:30:10 +0000 (20:30 +0200)]
clk: bcm2835: fix bcm2835_clock_choose_div
The commit 09e3b18ca5de ("clk: bcm2835: Remove unused variable")
accidentially breaks the behavior of bcm2835_clock_choose_div() and
booting of Raspberry Pi. The removed do_div macro call had side effects,
so we need to restore it.
Fixes: 09e3b18ca5de ("clk: bcm2835: Remove unused variable") Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com> Link: https://lore.kernel.org/r/20220428183010.1635248-1-stefan.wahren@i2se.com Tested-by: Maxime Ripard <maxime@cerno.tech> Acked-by: Maxime Ripard <maxime@cerno.tech> Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Stephen Boyd [Tue, 17 May 2022 06:53:06 +0000 (23:53 -0700)]
Merge tag 'for-5.19-clk' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into clk-tegra
Pull Tegra clk driver updates from Thierry Reding:
This contains a boot time optimization for Tegra chips with BPMP and a
switch from .round_rate() to .determine_rate() to take into account any
maximum rate that might have been set.
Other than that this contains a fix for a DFLL regression on Tegra210
and kerneldoc fixups to avoid build warnings.
* tag 'for-5.19-clk' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
clk: tegra: Update kerneldoc to match prototypes
clk: tegra: Replace .round_rate() with .determine_rate()
clk: tegra: Register clocks from root to leaf
clk: tegra: Add missing reset deassertion
Stephen Boyd [Tue, 17 May 2022 06:46:45 +0000 (23:46 -0700)]
Merge tag 'renesas-clk-for-v5.19-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers into clk-renesas
Pull Renesas clk driver updates from Geert Uytterhoeven:
- Add support for the R-Car V4H and RZ/V2M SoCs
- Add the Universal Flash Storage clock on R-Car S4-8
- Add I2C, SSIF-2 (sound), USB, CANFD, OSTM (timer), WDT, SPI Multi
I/O Bus, RSPI, TSU (thermal), and ADC clocks and resets on RZ/G2UL
- Add display clock support on RZ/G2L
- Miscellaneous fixes and improvements
* tag 'renesas-clk-for-v5.19-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers: (36 commits)
clk: renesas: r9a09g011: Add eth clock and reset entries
clk: renesas: Add RZ/V2M support using the rzg2l driver
clk: renesas: rzg2l: Add support for RZ/V2M reset monitor reg
clk: renesas: rzg2l: Make use of CLK_MON registers optional
clk: renesas: rzg2l: Set HIWORD mask for all mux and dividers
clk: renesas: rzg2l: Add read only versions of the clk macros
clk: renesas: rzg2l: Move the DEF_MUX array size calc into the macro
dt-bindings: clock: renesas,rzg2l: Document RZ/V2M SoC
clk: renesas: r9a07g044: Fix OSTM1 module clock name
clk: renesas: r9a07g043: Add clock and reset entries for ADC
clk: renesas: r9a07g043: Add TSU clock and reset entry
clk: renesas: r9a07g043: Add RSPI clock and reset entries
clk: renesas: r9a07g043: Add clock and reset entries for SPI Multi I/O Bus Controller
clk: renesas: r9a07g044: Add DSI clock and reset entries
clk: renesas: r9a07g044: Add LCDC clock and reset entries
clk: renesas: r9a07g044: Add M4 Clock support
clk: renesas: r9a07g044: Add M3 Clock support
clk: renesas: r9a07g044: Add {M2, M2_DIV2} Clocks support
clk: renesas: r9a07g044: Add M1 clock support
clk: renesas: rzg2l: Add DSI divider clk support
...
Miaoqian Lin [Mon, 16 May 2022 21:55:55 +0000 (14:55 -0700)]
Input: sparcspkr - fix refcount leak in bbc_beep_probe
of_find_node_by_path() calls of_find_node_opts_by_path(),
which returns a node pointer with refcount
incremented, we should use of_node_put() on it when done.
Add missing of_node_put() to avoid refcount leak.
dt-bindings: remoteproc: mediatek: Add optional memory-region to mtk,scp
The SCP co-processor can optionally be passed a reserved memory region
to use. Add this property in the dt-binding.
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Acked-by: Rob Herring <robh@kernel.org> Link: https://lore.kernel.org/r/20220511195452.871897-3-nfraprado@collabora.com Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
dt-bindings: remoteproc: mediatek: Make l1tcm reg exclusive to mt819x
Commit ca23ecfdbd44 ("remoteproc/mediatek: support L1TCM") added support
for the l1tcm memory region on the MT8192 SCP, adding a new da_to_va
callback that handles l1tcm while keeping the old one for
back-compatibility with MT8183. However, since the mt8192 compatible was
missing from the dt-binding, the accompanying dt-binding commit 503c64cc42f1 ("dt-bindings: remoteproc: mediatek: add L1TCM memory region")
mistakenly added this reg as if it were for mt8183. And later
it became common to all platforms as their compatibles were added.
Fix the dt-binding so that the l1tcm reg can be present only on the
supported platforms: mt8192 and mt8195.
Fixes: 503c64cc42f1 ("dt-bindings: remoteproc: mediatek: add L1TCM memory region") Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com> Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Link: https://lore.kernel.org/r/20220511195452.871897-2-nfraprado@collabora.com Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
scsi: bnx2fc: Avoid using get_cpu() in bnx2fc_cmd_alloc()
Using get_cpu() leads to disabling preemption and in this context it is not
possible to acquire the following spinlock_t on PREEMPT_RT because it
becomes a sleeping lock.
Commit 0ea5c27583e1 ("[SCSI] bnx2fc: common free list for cleanup
commands") says that it is using get_cpu() as a fix in case the CPU is
preempted. While this might be true, the important part is that it is now
using the same CPU for locking and unlocking while previously it always
relied on smp_processor_id(). The date structure itself is protected with
a lock so it does not rely on CPU-local access.
Replace get_cpu() with raw_smp_processor_id() to obtain the current CPU
number which is used as an index for the per-CPU resource.
Davidlohr Bueso [Fri, 6 May 2022 10:57:57 +0000 (12:57 +0200)]
scsi: libfc: Remove get_cpu() semantics in fc_exch_em_alloc()
The get_cpu() in fc_exch_em_alloc() was introduced in commit f018b73af6db
("[SCSI] libfc, libfcoe, fcoe: use smp_processor_id() only when preempt
disabled") for no other reason than to simply use smp_processor_id()
without getting a warning, because everything is done with the pool->lock
held anyway. However, get_cpu(), by disabling preemption, does not play
well with PREEMPT_RT, particularly when acquiring a regular (and thus
sleepable) spinlock.
Therefore remove the get_cpu() and just use the unstable value as we will
have CPU locality guarantees next by taking the lock. The window of
migration, as noted by Sebastian, is small and even if it happens the
result is correct.
scsi: fcoe: Use per-CPU API to update per-CPU statistics
The per-CPU statistics (struct fc_stats) is updated by getting a stable
per-CPU pointer via get_cpu() + per_cpu_ptr() and then performing the
increment. This can be optimized by using this_cpu_*() which will do
whatever is needed on the architecture to perform the update safe and
efficient. The read out of the individual value (fc_get_host_stats())
should be done by using READ_ONCE() instead of a plain-C access. The
difference is that READ_ONCE() will always perform a single access while
the plain-C access can be split by the compiler into two loads if it
appears beneficial. The usage of u64 has the side-effect that it is also
64bit wide on 32bit architectures and the read is always split into two
loads. The can lead to strange values if the read happens during an update
which alters both 32bit parts of the 64bit value. This can be circumvented
by either using a 32bit variables on 32bit architecures or extending the
statistics with a sequence counter.
Use this_cpu_*() API to update the statistics and READ_ONCE() to read it.
Davidlohr Bueso [Fri, 6 May 2022 10:57:55 +0000 (12:57 +0200)]
scsi: fcoe: Add a local_lock to fcoe_percpu
fcoe_get_paged_crc_eof() relies on the caller having preemption disabled to
ensure the per-CPU fcoe_percpu context remains valid throughout the
call. This is done by either holding spinlocks (such as bnx2fc_global_lock
or qedf_global_lock) or the get_cpu() from fcoe_alloc_paged_crc_eof(). This
last one breaks PREEMPT_RT semantics as there can be memory allocation and
end up sleeping in atomic contexts.
Introduce a local_lock_t to struct fcoe_percpu that will keep the non-RT
case the same, mapping to preempt_disable/enable, while RT will use a
per-CPU spinlock allowing the region to be preemptible but still maintain
CPU locality. The other users of fcoe_percpu are already safe in this
regard and do not require local_lock()ing.
Cast pointers to unsigned long instead of to uint64_t to avoid this
problem on 32-bit arches:
31 6.89 debian:experimental-x-mips : FAIL gcc version 11.2.0 (Debian 11.2.0-18)
bench/breakpoint.c: In function 'breakpoint_setup':
bench/breakpoint.c:56:24: error: cast from pointer to integer of different size [-Werror=pointer-to-int-cast]
56 | attr.bp_addr = (uint64_t)addr;
| ^
cc1: all warnings being treated as errors
make[3]: *** [/git/perf-5.18.0-rc7/tools/build/Makefile.build:139: bench] Error 2
Fixes: 68a6772f11dbb1ed ("perf bench: Add breakpoint benchmarks") Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Dmitriy Vyukov <dvyukov@google.com> Cc: Ian Rogers <irogers@google.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Marco Elver <elver@google.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Link: http://lore.kernel.org/lkml/YoLq1nHx1doi+VWl@kernel.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
the first 2 patches are by me and target the CAN raw protocol. The 1st
removes an unneeded assignment, the other one adds support for
SO_TXTIME/SCM_TXTIME.
Oliver Hartkopp contributes 2 patches for the ISOTP protocol. The 1st
adds support for transmission without flow control, the other let's
bind() return an error on incorrect CAN ID formatting.
Geert Uytterhoeven contributes a patch to clean up ctucanfd's Kconfig
file.
Vincent Mailhol's patch for the slcan driver uses the proper function
to check for invalid CAN frames in the xmit callback.
The next patch is by Geert Uytterhoeven and makes the interrupt-names
of the renesas,rcar-canfd dt bindings mandatory.
A patch by my update the ctucanfd dt bindings to include the common
CAN controller bindings.
The last patch is by Akira Yokosawa and fixes a breakage the
ctucanfd's documentation.
* tag 'linux-can-next-for-5.19-20220516' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next:
docs: ctucanfd: Use 'kernel-figure' directive instead of 'figure'
dt-bindings: can: ctucanfd: include common CAN controller bindings
dt-bindings: can: renesas,rcar-canfd: Make interrupt-names required
can: slcan: slc_xmit(): use can_dropped_invalid_skb() instead of manual check
can: ctucanfd: Let users select instead of depend on CAN_CTUCANFD
can: isotp: isotp_bind(): return -EINVAL on incorrect CAN ID formatting
can: isotp: add support for transmission without flow control
can: raw: add support for SO_TXTIME/SCM_TXTIME
can: raw: raw_sendmsg(): remove not needed setting of skb->sk
====================
Yuanzheng Song [Thu, 5 May 2022 07:10:37 +0000 (07:10 +0000)]
mm: usercopy: move the virt_addr_valid() below the is_vmalloc_addr()
The is_kmap_addr() and the is_vmalloc_addr() in the check_heap_object()
will not work, because the virt_addr_valid() will exclude the kmap and
vmalloc regions. So let's move the virt_addr_valid() below
the is_vmalloc_addr().
With all randstruct exceptions removed, remove all the exception
handling code. Any future warnings are likely to be shared between
this plugin and Clang randstruct, and will need to be addressed in a
more wholistic fashion.
Cc: Christoph Hellwig <hch@infradead.org> Cc: linux-hardening@vger.kernel.org Signed-off-by: Kees Cook <keescook@chromium.org>
Kees Cook [Tue, 10 May 2022 22:46:26 +0000 (15:46 -0700)]
af_unix: Silence randstruct GCC plugin warning
While preparing for Clang randstruct support (which duplicated many of
the warnings the randstruct GCC plugin warned about), one strange one
remained only for the randstruct GCC plugin. Eliminating this rids
the plugin of the last exception.
It seems the plugin is happy to dereference individual members of
a cross-struct cast, but it is upset about casting to a whole object
pointer. This only manifests in one place in the kernel, so just replace
the variable with individual member accesses. There is no change in
executable instruction output.
Drop the last exception from the randstruct GCC plugin.
Cc: "David S. Miller" <davem@davemloft.net> Cc: Christoph Hellwig <hch@infradead.org> Cc: Paolo Abeni <pabeni@redhat.com> Cc: Alexei Starovoitov <ast@kernel.org> Cc: Cong Wang <cong.wang@bytedance.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: netdev@vger.kernel.org Cc: linux-hardening@vger.kernel.org Acked-by: Kuniyuki Iwashima <kuniyu@amazon.co.jp> Link: https://lore.kernel.org/lkml/20220511022217.58586-1-kuniyu@amazon.co.jp Acked-by: Jakub Kicinski <kuba@kernel.org> Link: https://lore.kernel.org/lkml/20220511151542.4cb3ff17@kernel.org Signed-off-by: Kees Cook <keescook@chromium.org>
Kees Cook [Mon, 9 May 2022 22:11:54 +0000 (15:11 -0700)]
niu: Silence randstruct warnings
Clang randstruct gets upset when it sees struct addresspace (which is
randomized) being assigned to a struct page (which is not randomized):
drivers/net/ethernet/sun/niu.c:3385:12: error: casting from randomized structure pointer type 'struct address_space *' to 'struct page *'
*link = (struct page *) page->mapping;
^
It looks like niu.c is looking for an in-line place to chain its allocated
pages together and is overloading the "mapping" member, as it is unused.
This is very non-standard, and is expected to be cleaned up in the
future[1], but there is no "correct" way to handle it today.
No meaningful machine code changes result after this change, and source
readability is improved.
Drop the randstruct exception now that there is no "confusing" cross-type
assignment.
Kees Cook [Sun, 8 May 2022 16:15:53 +0000 (09:15 -0700)]
big_keys: Use struct for internal payload
The randstruct GCC plugin gets upset when it sees struct path (which is
randomized) being assigned from a "void *" (which it cannot type-check).
There's no need for these casts, as the entire internal payload use is
following a normal struct layout. Convert the enum-based void * offset
dereferencing to the new big_key_payload struct. No meaningful machine
code changes result after this change, and source readability is improved.
Drop the randstruct exception now that there is no "confusing" cross-type
assignment.
Cc: David Howells <dhowells@redhat.com> Cc: Eric Biggers <ebiggers@kernel.org> Cc: Christoph Hellwig <hch@infradead.org> Cc: Jarkko Sakkinen <jarkko@kernel.org> Cc: James Morris <jmorris@namei.org> Cc: "Serge E. Hallyn" <serge@hallyn.com> Cc: linux-hardening@vger.kernel.org Cc: keyrings@vger.kernel.org Cc: linux-security-module@vger.kernel.org Signed-off-by: Kees Cook <keescook@chromium.org>
Baolin Wang [Mon, 16 May 2022 00:55:58 +0000 (08:55 +0800)]
arm64/hugetlb: Implement arm64 specific huge_ptep_get()
Now we use huge_ptep_get() to get the pte value of a hugetlb page,
however it will only return one specific pte value for the CONT-PTE
or CONT-PMD size hugetlb on ARM64 system, which can contain several
continuous pte or pmd entries with same page table attributes. And it
will not take into account the subpages' dirty or young bits of a
CONT-PTE/PMD size hugetlb page.
So the huge_ptep_get() is inconsistent with huge_ptep_get_and_clear(),
which already takes account the dirty or young bits for any subpages
in this CONT-PTE/PMD size hugetlb [1]. Meanwhile we can miss dirty or
young flags statistics for hugetlb pages with current huge_ptep_get(),
such as the gather_hugetlb_stats() function, and CONT-PTE/PMD hugetlb
monitoring with DAMON.
Thus define an ARM64 specific huge_ptep_get() implementation as well as
enabling __HAVE_ARCH_HUGE_PTEP_GET, that will take into account any
subpages' dirty or young bits for CONT-PTE/PMD size hugetlb page, for
those functions that want to check the dirty and young flags of a hugetlb
page.
Baolin Wang [Mon, 16 May 2022 00:55:57 +0000 (08:55 +0800)]
arm64/hugetlb: Use ptep_get() to get the pte value of a huge page
The original huge_ptep_get() on ARM64 is just a wrapper of ptep_get(),
which will not take into account any contig-PTEs dirty and access bits.
Meanwhile we will implement a new ARM64-specific huge_ptep_get()
interface in following patch, which will take into account any contig-PTEs
dirty and access bits. To keep the same efficient logic to get the pte
value, change to use ptep_get() as a preparation.
Darrick J. Wong [Mon, 16 May 2022 22:27:38 +0000 (15:27 -0700)]
iomap: don't invalidate folios after writeback errors
XFS has the unique behavior (as compared to the other Linux filesystems)
that on writeback errors it will completely invalidate the affected
folio and force the page cache to reread the contents from disk. All
other filesystems leave the page mapped and up to date.
This is a rude awakening for user programs, since (in the case where
write fails but reread doesn't) file contents will appear to revert to
old disk contents with no notification other than an EIO on fsync. This
might have been annoying back in the days when iomap dealt with one page
at a time, but with multipage folios, we can now throw away *megabytes*
worth of data for a single write error.
On *most* Linux filesystems, a program can respond to an EIO on write by
redirtying the entire file and scheduling it for writeback. This isn't
foolproof, since the page that failed writeback is no longer dirty and
could be evicted, but programs that want to recover properly *also*
have to detect XFS and regenerate every write they've made to the file.
When running xfs/314 on arm64, I noticed a UAF when xfs_discard_folio
invalidates multipage folios that could be undergoing writeback. If,
say, we have a 256K folio caching a mix of written and unwritten
extents, it's possible that we could start writeback of the first (say)
64K of the folio and then hit a writeback error on the next 64K. We
then free the iop attached to the folio, which is really bad because
writeback completion on the first 64k will trip over the "blocks per
folio > 1 && !iop" assertion.
This can't be fixed by only invalidating the folio if writeback fails at
the start of the folio, since the folio is marked !uptodate, which trips
other assertions elsewhere. Get rid of the whole behavior entirely.
Signed-off-by: Darrick J. Wong <djwong@kernel.org> Reviewed-by: Matthew Wilcox (Oracle) <willy@infradead.org> Reviewed-by: Jeff Layton <jlayton@kernel.org> Reviewed-by: Christoph Hellwig <hch@lst.de>
Reinette Chatre [Thu, 12 May 2022 21:51:01 +0000 (14:51 -0700)]
x86/sgx: Ensure no data in PCMD page after truncate
A PCMD (Paging Crypto MetaData) page contains the PCMD
structures of enclave pages that have been encrypted and
moved to the shmem backing store. When all enclave pages
sharing a PCMD page are loaded in the enclave, there is no
need for the PCMD page and it can be truncated from the
backing store.
A few issues appeared around the truncation of PCMD pages. The
known issues have been addressed but the PCMD handling code could
be made more robust by loudly complaining if any new issue appears
in this area.
Add a check that will complain with a warning if the PCMD page is not
actually empty after it has been truncated. There should never be data
in the PCMD page at this point since it is was just checked to be empty
and truncated with enclave mutex held and is updated with the
enclave mutex held.
Reinette Chatre [Thu, 12 May 2022 21:51:00 +0000 (14:51 -0700)]
x86/sgx: Fix race between reclaimer and page fault handler
Haitao reported encountering a WARN triggered by the ENCLS[ELDU]
instruction faulting with a #GP.
The WARN is encountered when the reclaimer evicts a range of
pages from the enclave when the same pages are faulted back right away.
Consider two enclave pages (ENCLAVE_A and ENCLAVE_B)
sharing a PCMD page (PCMD_AB). ENCLAVE_A is in the
enclave memory and ENCLAVE_B is in the backing store. PCMD_AB contains
just one entry, that of ENCLAVE_B.
Scenario proceeds where ENCLAVE_A is being evicted from the enclave
while ENCLAVE_B is faulted in.
sgx_reclaim_pages() {
...
/*
* Reclaim ENCLAVE_A
*/
mutex_lock(&encl->lock);
/*
* Get a reference to ENCLAVE_A's
* shmem page where enclave page
* encrypted data will be stored
* as well as a reference to the
* enclave page's PCMD data page,
* PCMD_AB.
* Release mutex before writing
* any data to the shmem pages.
*/
sgx_encl_get_backing(...);
encl_page->desc |= SGX_ENCL_PAGE_BEING_RECLAIMED;
mutex_unlock(&encl->lock);
/*
* Fault ENCLAVE_B
*/
sgx_vma_fault() {
mutex_lock(&encl->lock);
/*
* Get reference to
* ENCLAVE_B's shmem page
* as well as PCMD_AB.
*/
sgx_encl_get_backing(...)
/*
* Load page back into
* enclave via ELDU.
*/
/*
* Release reference to
* ENCLAVE_B' shmem page and
* PCMD_AB.
*/
sgx_encl_put_backing(...);
/*
* PCMD_AB is found empty so
* it and ENCLAVE_B's shmem page
* are truncated.
*/
/* Truncate ENCLAVE_B backing page */
sgx_encl_truncate_backing_page();
/* Truncate PCMD_AB */
sgx_encl_truncate_backing_page();
mutex_unlock(&encl->lock);
...
}
mutex_lock(&encl->lock);
encl_page->desc &=
~SGX_ENCL_PAGE_BEING_RECLAIMED;
/*
* Write encrypted contents of
* ENCLAVE_A to ENCLAVE_A shmem
* page and its PCMD data to
* PCMD_AB.
*/
sgx_encl_put_backing(...)
/*
* Reference to PCMD_AB is
* dropped and it is truncated.
* ENCLAVE_A's PCMD data is lost.
*/
mutex_unlock(&encl->lock);
}
What happens next depends on whether it is ENCLAVE_A being faulted
in or ENCLAVE_B being evicted - but both end up with ENCLS[ELDU] faulting
with a #GP.
If ENCLAVE_A is faulted then at the time sgx_encl_get_backing() is called
a new PCMD page is allocated and providing the empty PCMD data for
ENCLAVE_A would cause ENCLS[ELDU] to #GP
If ENCLAVE_B is evicted first then a new PCMD_AB would be allocated by the
reclaimer but later when ENCLAVE_A is faulted the ENCLS[ELDU] instruction
would #GP during its checks of the PCMD value and the WARN would be
encountered.
Noting that the reclaimer sets SGX_ENCL_PAGE_BEING_RECLAIMED at the time
it obtains a reference to the backing store pages of an enclave page it
is in the process of reclaiming, fix the race by only truncating the PCMD
page after ensuring that no page sharing the PCMD page is in the process
of being reclaimed.
Cc: stable@vger.kernel.org Fixes: 08999b2489b4 ("x86/sgx: Free backing memory after faulting the enclave page") Reported-by: Haitao Huang <haitao.huang@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com> Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org> Tested-by: Haitao Huang <haitao.huang@intel.com> Link: https://lkml.kernel.org/r/ed20a5db516aa813873268e125680041ae11dfcf.1652389823.git.reinette.chatre@intel.com
Reinette Chatre [Thu, 12 May 2022 21:50:59 +0000 (14:50 -0700)]
x86/sgx: Obtain backing storage page with enclave mutex held
Haitao reported encountering a WARN triggered by the ENCLS[ELDU]
instruction faulting with a #GP.
The WARN is encountered when the reclaimer evicts a range of
pages from the enclave when the same pages are faulted back
right away.
The SGX backing storage is accessed on two paths: when there
are insufficient free pages in the EPC the reclaimer works
to move enclave pages to the backing storage and as enclaves
access pages that have been moved to the backing storage
they are retrieved from there as part of page fault handling.
An oversubscribed SGX system will often run the reclaimer and
page fault handler concurrently and needs to ensure that the
backing store is accessed safely between the reclaimer and
the page fault handler. This is not the case because the
reclaimer accesses the backing store without the enclave mutex
while the page fault handler accesses the backing store with
the enclave mutex.
Consider the scenario where a page is faulted while a page sharing
a PCMD page with the faulted page is being reclaimed. The
consequence is a race between the reclaimer and page fault
handler, the reclaimer attempting to access a PCMD at the
same time it is truncated by the page fault handler. This
could result in lost PCMD data. Data may still be
lost if the reclaimer wins the race, this is addressed in
the following patch.
The reclaimer accesses pages from the backing storage without
holding the enclave mutex and runs the risk of concurrently
accessing the backing storage with the page fault handler that
does access the backing storage with the enclave mutex held.
In the scenario below a PCMD page is truncated from the backing
store after all its pages have been loaded in to the enclave
at the same time the PCMD page is loaded from the backing store
when one of its pages are reclaimed:
sgx_reclaim_pages() { sgx_vma_fault() {
...
mutex_lock(&encl->lock);
...
__sgx_encl_eldu() {
...
if (pcmd_page_empty) {
/*
* EPC page being reclaimed /*
* shares a PCMD page with an * PCMD page truncated
* enclave page that is being * while requested from
* faulted in. * reclaimer.
*/ */
sgx_encl_get_backing() <----------> sgx_encl_truncate_backing_page()
}
mutex_unlock(&encl->lock);
} }
In this scenario there is a race between the reclaimer and the page fault
handler when the reclaimer attempts to get access to the same PCMD page
that is being truncated. This could result in the reclaimer writing to
the PCMD page that is then truncated, causing the PCMD data to be lost,
or in a new PCMD page being allocated. The lost PCMD data may still occur
after protecting the backing store access with the mutex - this is fixed
in the next patch. By ensuring the backing store is accessed with the mutex
held the enclave page state can be made accurate with the
SGX_ENCL_PAGE_BEING_RECLAIMED flag accurately reflecting that a page
is in the process of being reclaimed.
Consistently protect the reclaimer's backing store access with the
enclave's mutex to ensure that it can safely run concurrently with the
page fault handler.
Cc: stable@vger.kernel.org Fixes: 1728ab54b4be ("x86/sgx: Add a page reclaimer") Reported-by: Haitao Huang <haitao.huang@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com> Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org> Tested-by: Jarkko Sakkinen <jarkko@kernel.org> Tested-by: Haitao Huang <haitao.huang@intel.com> Link: https://lkml.kernel.org/r/fa2e04c561a8555bfe1f4e7adc37d60efc77387b.1652389823.git.reinette.chatre@intel.com
Reinette Chatre [Thu, 12 May 2022 21:50:58 +0000 (14:50 -0700)]
x86/sgx: Mark PCMD page as dirty when modifying contents
Recent commit 08999b2489b4 ("x86/sgx: Free backing memory
after faulting the enclave page") expanded __sgx_encl_eldu()
to clear an enclave page's PCMD (Paging Crypto MetaData)
from the PCMD page in the backing store after the enclave
page is restored to the enclave.
Since the PCMD page in the backing store is modified the page
should be marked as dirty to ensure the modified data is retained.
Cc: stable@vger.kernel.org Fixes: 08999b2489b4 ("x86/sgx: Free backing memory after faulting the enclave page") Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com> Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org> Tested-by: Haitao Huang <haitao.huang@intel.com> Link: https://lkml.kernel.org/r/00cd2ac480db01058d112e347b32599c1a806bc4.1652389823.git.reinette.chatre@intel.com
Reinette Chatre [Thu, 12 May 2022 21:50:57 +0000 (14:50 -0700)]
x86/sgx: Disconnect backing page references from dirty status
SGX uses shmem backing storage to store encrypted enclave pages
and their crypto metadata when enclave pages are moved out of
enclave memory. Two shmem backing storage pages are associated with
each enclave page - one backing page to contain the encrypted
enclave page data and one backing page (shared by a few
enclave pages) to contain the crypto metadata used by the
processor to verify the enclave page when it is loaded back into
the enclave.
sgx_encl_put_backing() is used to release references to the
backing storage and, optionally, mark both backing store pages
as dirty.
Managing references and dirty status together in this way results
in both backing store pages marked as dirty, even if only one of
the backing store pages are changed.
Additionally, waiting until the page reference is dropped to set
the page dirty risks a race with the page fault handler that
may load outdated data into the enclave when a page is faulted
right after it is reclaimed.
Consider what happens if the reclaimer writes a page to the backing
store and the page is immediately faulted back, before the reclaimer
is able to set the dirty bit of the page:
sgx_reclaim_pages() { sgx_vma_fault() {
...
sgx_encl_get_backing();
... ...
sgx_reclaimer_write() {
mutex_lock(&encl->lock);
/* Write data to backing store */
mutex_unlock(&encl->lock);
}
mutex_lock(&encl->lock);
__sgx_encl_eldu() {
...
/*
* Enclave backing store
* page not released
* nor marked dirty -
* contents may not be
* up to date.
*/
sgx_encl_get_backing();
...
/*
* Enclave data restored
* from backing store
* and PCMD pages that
* are not up to date.
* ENCLS[ELDU] faults
* because of MAC or PCMD
* checking failure.
*/
sgx_encl_put_backing();
}
...
/* set page dirty */
sgx_encl_put_backing();
...
mutex_unlock(&encl->lock);
} }
Remove the option to sgx_encl_put_backing() to set the backing
pages as dirty and set the needed pages as dirty right after
receiving important data while enclave mutex is held. This ensures that
the page fault handler can get up to date data from a page and prepares
the code for a following change where only one of the backing pages
need to be marked as dirty.
Stefan Berger [Thu, 21 Apr 2022 17:52:05 +0000 (13:52 -0400)]
integrity: Fix sparse warnings in keyring_handler
Fix the following sparse warnings:
CHECK security/integrity/platform_certs/keyring_handler.c
security/integrity/platform_certs/keyring_handler.c:76:16: warning: Using plain integer as NULL pointer
security/integrity/platform_certs/keyring_handler.c:91:16: warning: Using plain integer as NULL pointer
security/integrity/platform_certs/keyring_handler.c:106:16: warning: Using plain integer as NULL pointer
Signed-off-by: Stefan Berger <stefanb@linux.ibm.com> Signed-off-by: Mimi Zohar <zohar@linux.ibm.com>
This commit broke support for setting interrupt affinity. It looks like
that it is related to the chained IRQ handler. Revert this commit until
issue with setting interrupt affinity is fixed.
Ricardo Martinez [Fri, 13 May 2022 17:34:00 +0000 (10:34 -0700)]
net: skb: Remove skb_data_area_size()
skb_data_area_size() is not needed. As Jakub pointed out [1]:
For Rx, drivers can use the size passed during skb allocation or
use skb_tailroom().
For Tx, drivers should use skb_headlen().
Ricardo Martinez [Fri, 13 May 2022 17:33:59 +0000 (10:33 -0700)]
net: wwan: t7xx: Avoid calls to skb_data_area_size()
skb_data_area_size() helper was used to calculate the size of the
DMA mapped buffer passed to the HW. Instead of doing this, use the
size passed to allocate the skbs.
Signed-off-by: Ricardo Martinez <ricardo.martinez@linux.intel.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: Sergey Ryazanov <ryazanov.s.a@gmail.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jane Chu [Fri, 13 May 2022 22:13:20 +0000 (15:13 -0700)]
pmem: implement pmem_recovery_write()
The recovery write thread started out as a normal pwrite thread and
when the filesystem was told about potential media error in the
range, filesystem turns the normal pwrite to a dax_recovery_write.
The recovery write consists of clearing media poison, clearing page
HWPoison bit, reenable page-wide read-write permission, flush the
caches and finally write. A competing pread thread will be held
off during the recovery process since data read back might not be
valid, and this is achieved by clearing the badblock records after
the recovery write is complete. Competing recovery write threads
are already serialized by writer lock held by dax_iomap_rw().
Jane Chu [Fri, 22 Apr 2022 22:45:06 +0000 (16:45 -0600)]
dax: add .recovery_write dax_operation
Introduce dax_recovery_write() operation. The function is used to
recover a dax range that contains poison. Typical use case is when
a user process receives a SIGBUS with si_code BUS_MCEERR_AR
indicating poison(s) in a dax range, in response, the user process
issues a pwrite() to the page-aligned dax range, thus clears the
poison and puts valid data in the range.
Jane Chu [Fri, 13 May 2022 22:10:58 +0000 (15:10 -0700)]
dax: introduce DAX_RECOVERY_WRITE dax access mode
Up till now, dax_direct_access() is used implicitly for normal
access, but for the purpose of recovery write, dax range with
poison is requested. To make the interface clear, introduce
enum dax_access_mode {
DAX_ACCESS,
DAX_RECOVERY_WRITE,
}
where DAX_ACCESS is used for normal dax access, and
DAX_RECOVERY_WRITE is used for dax recovery write.
Additional locks are not needed, all the touched sections
are already under mptcp socket lock protection.
Fixes: 4293248c6704 ("mptcp: add data lock for sk timers") Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Geliang Tang [Sat, 14 May 2022 00:21:13 +0000 (17:21 -0700)]
selftests: mptcp: fix a mp_fail test warning
Old tc versions (iproute2 5.3) show actions in multiple lines, not a
single line. Then the following unexpected MP_FAIL selftest output
occurs:
file received by server has inverted byte at 169
./mptcp_join.sh: line 1277: [: [{"total acts":1},{"actions":[{"order":0 pedit ,"control_action":{"type":"pipe"}keys 1
index 1 ref 1 bind 1,"installed":0,"last_used":0
key #0 at 148: val ff000000 mask ffffffff
5: integer expression expected
001 Infinite map syn[ ok ] - synack[ ok ] - ack[ ok ]
sum[ ok ] - csum [ ok ]
ftx[ ok ] - failrx[ ok ]
rtx[ ok ] - rstrx [ ok ]
itx[ ok ] - infirx[ ok ]
ftx[ ok ] - failrx[ ok ] invert
This patch adds a 'grep' before 'sed' to fix this.
Akira Yokosawa [Tue, 10 May 2022 23:45:43 +0000 (08:45 +0900)]
docs: ctucanfd: Use 'kernel-figure' directive instead of 'figure'
Two issues were observed in the ReST doc added by commit c3a0addefbde
("docs: ctucanfd: CTU CAN FD open-source IP core documentation.")
with Sphinx versions 2.4.4 and 4.5.0.
The plain "figure" directive broke "make pdfdocs" due to a missing
PDF figure. For conversion of SVG -> PDF to work, the "kernel-figure"
directive, which is an extension for kernel documentation, should
be used instead.
The directive of "code:: raw" causes a warning from both
"make htmldocs" and "make pdfdocs", which reads:
[...]/can/ctu/ctucanfd-driver.rst:75: WARNING: Pygments lexer name
'raw' is not known
A plain literal-block marker should suffice where no syntax
highlighting is intended.
Fix the issues by using suitable directive and marker.
Fixes: c3a0addefbde ("docs: ctucanfd: CTU CAN FD open-source IP core documentation.") Link: https://lore.kernel.org/all/5986752a-1c2a-5d64-f91d-58b1e6decd17@gmail.com Signed-off-by: Akira Yokosawa <akiyks@gmail.com> Acked-by: Pavel Pisa <pisa@cmp.felk.cvut.cz> Cc: Martin Jerabek <martin.jerabek01@gmail.com> Cc: Ondrej Ille <ondrej.ille@gmail.com> Cc: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
there is a common CAN controller binding. Add this to the ctucanfd
binding.
Cc: Ondrej Ille <ondrej.ille@gmail.com> Acked-by: Pavel Pisa <pisa@cmp.felk.cvut.cz> Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Jonathan Lemon [Fri, 13 May 2022 22:52:31 +0000 (15:52 -0700)]
ptp: ocp: have adjtime handle negative delta_ns correctly
delta_ns is a s64, but it was being passed ptp_ocp_adjtime_coarse
as an u64. Also, it turns out that timespec64_add_ns() only handles
positive values, so perform the math with set_normalized_timespec().
Fixes: 90f8f4c0e3ce ("ptp: ocp: Add ptp_ocp_adjtime_coarse for large adjustments") Suggested-by: Vadim Fedorenko <vfedorenko@novek.ru> Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com> Acked-by: Vadim Fedorenko <vfedorenko@novek.ru> Link: https://lore.kernel.org/r/20220513225231.1412-1-jonathan.lemon@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
dt-bindings: can: renesas,rcar-canfd: Make interrupt-names required
The Renesas R-Car CAN FD Controller always uses two or more interrupts.
Make the interrupt-names properties a required property, to make it
easier to identify the individual interrupts.
can: ctucanfd: Let users select instead of depend on CAN_CTUCANFD
The CTU CAN-FD IP core is only useful when used with one of the
corresponding PCI/PCIe or platform (FPGA, SoC) drivers, which depend on
PCI resp. OF.
Hence make the users select the core driver code, instead of letting
then depend on it. Keep the core code config option visible when
compile-testing, to maintain compile-coverage.
Oliver Hartkopp [Sun, 15 May 2022 18:16:33 +0000 (20:16 +0200)]
can: isotp: isotp_bind(): return -EINVAL on incorrect CAN ID formatting
Commit 3ea566422cbd ("can: isotp: sanitize CAN ID checks in
isotp_bind()") checks the given CAN ID address information by
sanitizing the input values.
This check (silently) removes obsolete bits by masking the given CAN
IDs.
Derek Will suggested to give a feedback to the application programmer
when the 'sanitizing' was actually needed which means the programmer
provided CAN ID content in a wrong format (e.g. SFF CAN IDs with a CAN
ID > 0x7FF).
Oliver Hartkopp [Sat, 7 May 2022 11:55:58 +0000 (13:55 +0200)]
can: isotp: add support for transmission without flow control
Usually the ISO 15765-2 protocol is a point-to-point protocol to transfer
segmented PDUs to a dedicated receiver. This receiver sends a flow control
message to specify protocol options and timings (e.g. block size / STmin).
The so called functional addressing communication allows a 1:N
communication but is limited to a single frame length.
This new CAN_ISOTP_CF_BROADCAST allows an unconfirmed 1:N communication
with PDU length that would not fit into a single frame. This feature is
not covered by the ISO 15765-2 standard.
This patch calls into sock_cmsg_send() to parse the user supplied
control information into a struct sockcm_cookie. Then assign the
requested transmit time to the skb.
This makes it possible to use the Earliest TXTIME First (ETF) packet
scheduler with the CAN_RAW protocol. The user can send a CAN_RAW frame
with a TXTIME and the kernel (with the ETF scheduler) will take care
of sending it to the network interface.
can: raw: raw_sendmsg(): remove not needed setting of skb->sk
The skb in raw_sendmsg() is allocated with sock_alloc_send_skb(),
which subsequently calls sock_alloc_send_pskb() -> skb_set_owner_w(),
which assigns "skb->sk = sk".
This patch removes the not needed setting of skb->sk.
Fabio Estevam [Fri, 13 May 2022 11:46:13 +0000 (08:46 -0300)]
net: phy: micrel: Use the kszphy probe/suspend/resume
Now that it is possible to use .probe without having .driver_data, let
KSZ8061 use the kszphy specific hooks for probe,suspend and resume,
which is preferred.
Switch to using the dedicated kszphy probe/suspend/resume functions.
Brendan Higgins [Thu, 12 May 2022 00:30:26 +0000 (17:30 -0700)]
kunit: tool: update riscv QEMU config with new serial dependency
The config for the serial console for riscv,
CONFIG_SERIAL_EARLYCON_RISCV_SBI, added a dependency,
CONFIG_RISCV_SBI_V01, at some point, so add that in to the base arch
config.
Marco Elver [Wed, 4 May 2022 07:09:41 +0000 (09:09 +0200)]
kcsan: test: use new suite_{init,exit} support
Use the newly added suite_{init,exit} support for suite-wide init and
cleanup. This avoids the unsupported method by which the test used to do
suite-wide init and cleanup (avoiding issues such as missing TAP
headers, and possible future conflicts).
Signed-off-by: Marco Elver <elver@google.com> Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
David Gow [Sat, 30 Apr 2022 04:56:40 +0000 (12:56 +0800)]
kunit: tool: Add list of all valid test configs on UML
It's often desirable (particularly in test automation) to run as many
tests as possible. This config enables all the tests which work as
builtins under UML at present, increasing the total tests run from 156
to 342 (not counting 36 'skipped' tests).
They can be run with:
./tools/testing/kunit/kunit.py run
--kunitconfig=./tools/testing/kunit/configs/all_tests_uml.config
This acts as an in-between point between the KUNIT_ALL_TESTS config
(which enables only tests whose dependencies are already enabled), and
the kunit_tool --alltests option, which tries to use allyesconfig,
taking a very long time to build and breaking very often.
Signed-off-by: David Gow <davidgow@google.com> Tested-by: Daniel Latypov <dlatypov@google.com> Reviewed-by: Brendan Higgins <brendanhiggins@google.com> Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Miguel Ojeda [Mon, 2 May 2022 09:36:25 +0000 (11:36 +0200)]
kunit: take `kunit_assert` as `const`
The `kunit_do_failed_assertion` function passes its
`struct kunit_assert` argument to `kunit_fail`. This one,
in turn, calls its `format` field passing the assert again
as a `const` pointer.
Therefore, the whole chain may be made `const`.
Signed-off-by: Miguel Ojeda <ojeda@kernel.org> Reviewed-by: Daniel Latypov <dlatypov@google.com> Reviewed-by: Kees Cook <keescook@chromium.org> Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Daniel Latypov [Mon, 9 May 2022 20:49:09 +0000 (13:49 -0700)]
kunit: tool: misc cleanups
This primarily comes from running pylint over kunit tool code and
ignoring some warnings we don't care about.
If we ever got a fully clean setup, we could add this to run_checks.py,
but we're not there yet.
Fix things like
* Drop unused imports
* check `is None`, not `== None` (see PEP 8)
* remove redundant parens around returns
* remove redundant `else` / convert `elif` to `if` where appropriate
* rename make_arch_qemuconfig() param to base_kunitconfig (this is the
name used in the subclass, and it's a better one)
* kunit_tool_test: check the exit code for SystemExit (could be 0)
Signed-off-by: Daniel Latypov <dlatypov@google.com> Reviewed-by: David Gow <davidgow@google.com> Reviewed-by: Brendan Higgins <brendanhiggins@google.com> Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Daniel Latypov [Thu, 12 May 2022 18:35:37 +0000 (11:35 -0700)]
kunit: tool: make parser stop overwriting status of suites w/ no_tests
Consider this invocation
$ ./tools/testing/kunit/kunit.py parse <<EOF
TAP version 14
1..2
ok 1 - suite
# Subtest: no_tests_suite
# catastrophic error!
not ok 1 - no_tests_suite
EOF
It will have a 0 exit code even though there's a "not ok".
Consider this one:
$ ./tools/testing/kunit/kunit.py parse <<EOF
TAP version 14
1..2
ok 1 - suite
not ok 1 - no_tests_suite
EOF
It will a non-zero exit code.
Why?
We have this line in the kunit_parser.py
> parent_test = parse_test_header(lines, test)
where we have special handling when we see "# Subtest" and we ignore the
explicit reported "not ok 1" status!
Also, NO_TESTS at a suite-level only results in a non-zero status code
where then there's only one suite atm.
This change is the minimal one to make sure we don't overwrite it.
Signed-off-by: Daniel Latypov <dlatypov@google.com> Reviewed-by: David Gow <davidgow@google.com> Reviewed-by: Brendan Higgins <brendanhiggins@google.com> Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Daniel Latypov [Thu, 12 May 2022 18:35:36 +0000 (11:35 -0700)]
kunit: tool: remove dead parse_crash_in_log() logic
This logic depends on the kernel logging a message containing
'kunit test case crashed', but there is no corresponding logic to do so.
This is likely a relic of the revision process KUnit initially went
through when being upstreamed.
Delete it given
1) it's been missing for years and likely won't get implemented
2) the parser has been moving to be a more general KTAP parser,
kunit-only magic like this isn't how we'd want to implement it.
Signed-off-by: Daniel Latypov <dlatypov@google.com> Reviewed-by: David Gow <davidgow@google.com> Reviewed-by: Brendan Higgins <brendanhiggins@google.com> Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Zhen Lei [Wed, 11 May 2022 03:20:32 +0000 (11:20 +0800)]
arm64: kdump: Do not allocate crash low memory if not needed
When "crashkernel=X,high" is specified, the specified "crashkernel=Y,low"
memory is not required in the following corner cases:
1. If both CONFIG_ZONE_DMA and CONFIG_ZONE_DMA32 are disabled, it means
that the devices can access any memory.
2. If the system memory is small, the crash high memory may be allocated
from the DMA zones. If that happens, there's no need to allocate
another crash low memory because there's already one.
Add condition '(crash_base >= CRASH_ADDR_LOW_MAX)' to determine whether
the 'high' memory is allocated above DMA zones. Note: when both
CONFIG_ZONE_DMA and CONFIG_ZONE_DMA32 are disabled, the entire physical
memory is DMA accessible, CRASH_ADDR_LOW_MAX equals 'PHYS_MASK + 1'.
Mark Brown [Mon, 16 May 2022 18:50:51 +0000 (19:50 +0100)]
firmware: mtk: add adsp ipc protocol for SOF
Merge series from Tinghan Shen <tinghan.shen@mediatek.com>:
This patch provides mediatek adsp ipc support for SOF.
ADSP IPC protocol offers (send/recv) interfaces using
mediatek-mailbox APIs.
This patch was tested and confirmed to work with SOF fw on
MT8195 cherry board and MT8186 krabby board.
changes since v8:
- fix patchset 2 and 3.
move "depends on MTK_ADSP_IPC" from SND_SOC_SOF_MTK_COMMON
to SND_SOC_SOF_MT8195/MT8186 to prevent generating wrong
config.
changes since v7:
- rebase to linux-next/next-22020504
- use EXPORT_SYMBOL_GPL instead of EXPORT_SYMBOL in mtk-adsp-ipc.c
- move mtk-adsp-ipc.c out from driver/firmware/mediatek
- add user of mtk-adsp-ipc.h in patchset 2 and 3.
changes since v6:
- rebase to matthias.bgg/linux.git, v5.18-next/soc
- Prefer "GPL" over "GPL v2" for MODULE_LICENSE
changes since v5:
- fix WARNING: modpost: missing MODULE_LICENSE() in drivers/mailbox
/mtk-adsp-mailbox.o. Add MODULE_LICENSE in the last line.
- Due to WARNING: Missing or malformed SPDX-License-Identifier tag
in line 1 in checkpatch, we don't remove SPDX-License in line 1.
changes since v4:
- add error message for wrong mbox chan
changes since v3:
- rebase on v5.16-rc8
- update reviewers
changes since v2:
- add out tag for two memory free phases
changes since v1:
- add comments for mtk_adsp_ipc_send and mtk_adsp_ipc_recv
- remove useless MODULE_LICENSE
- change label name to out_free
Allen-KH Cheng (1):
ASoC: SOF: mediatek: Add ipc support for mt8195
projects / people / ms / linux.git / log
