media: aspeed: Fix an error handling path in aspeed_video_probe()
A dma_free_coherent() call is missing in the error handling path of the
probe, as already done in the remove function.
In fact, this call is included in aspeed_video_free_buf(). So use the
latter both in the error handling path of the probe and in the remove
function.
It is easier to see the relation with aspeed_video_alloc_buf() this way.
The encoder node may be dependent on a power-domain. Add a property for
it.
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com> Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Merge tag 'usb-serial-5.18-rc7' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial
Johan writes:
USB-serial fixes for 5.18-rc7
Here are some new device ids.
All have been in linux-next with no reported issues.
* tag 'usb-serial-5.18-rc7' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: qcserial: add support for Sierra Wireless EM7590
USB: serial: option: add Fibocom MA510 modem
USB: serial: option: add Fibocom L610 modem
USB: serial: pl2303: add device id for HP LM930 Display
Qi Zheng [Fri, 13 May 2022 03:38:37 +0000 (20:38 -0700)]
tty: fix deadlock caused by calling printk() under tty_port->lock
pty_write() invokes kmalloc() which may invoke a normal printk() to print
failure message. This can cause a deadlock in the scenario reported by
syz-bot below:
As commit dbdda842fe96 ("printk: Add console owner and waiter logic to
load balance console writes") said, such deadlock can be prevented by
using printk_deferred() in kmalloc() (which is invoked in the section
guarded by the port->lock). But there are too many printk() on the
kmalloc() path, and kmalloc() can be called from anywhere, so changing
printk() to printk_deferred() is too complicated and inelegant.
Therefore, this patch chooses to specify __GFP_NOWARN to kmalloc(), so
that printk() will not be called, and this deadlock problem can be
avoided.
Syzbot reported the following lockdep error:
======================================================
WARNING: possible circular locking dependency detected 5.4.143-00237-g08ccc19a-dirty #10 Not tainted
------------------------------------------------------
syz-executor.4/29420 is trying to acquire lock: ffffffff8aedb2a0 (console_owner){....}-{0:0}, at: console_trylock_spinning kernel/printk/printk.c:1752 [inline] ffffffff8aedb2a0 (console_owner){....}-{0:0}, at: vprintk_emit+0x2ca/0x470 kernel/printk/printk.c:2023
but task is already holding lock: ffff8880119c9158 (&port->lock){-.-.}-{2:2}, at: pty_write+0xf4/0x1f0 drivers/tty/pty.c:120
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
Colin Ian King [Fri, 13 May 2022 03:38:37 +0000 (20:38 -0700)]
relay: remove redundant assignment to pointer buf
Pointer buf is being assigned a value that is not being read, buf is being
re-assigned in the next starement. The assignment is redundant and can be
removed.
Cleans up clang scan build warning:
kernel/relay.c:443:8: warning: Although the value stored to 'buf' is
used in the enclosing expression, the value is never actually read
from 'buf' [deadcode.DeadStores]
Link: https://lkml.kernel.org/r/20220508212152.58753-1-colin.i.king@gmail.com Signed-off-by: Colin Ian King <colin.i.king@gmail.com> Reviewed-by: Jens Axboe <axboe@kernel.dk> Cc: Christoph Hellwig <hch@lst.de> Cc: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Randy Dunlap [Fri, 13 May 2022 03:38:37 +0000 (20:38 -0700)]
fs/ntfs3: validate BOOT sectors_per_clusters
When the NTFS BOOT sectors_per_clusters field is > 0x80, it represents a
shift value. Make sure that the shift value is not too large before using
it (NTFS max cluster size is 2MB). Return -EVINVAL if it too large.
This prevents negative shift values and shift values that are larger than
the field size.
Prevents this UBSAN error:
UBSAN: shift-out-of-bounds in ../fs/ntfs3/super.c:673:16
shift exponent -192 is negative
Link: https://lkml.kernel.org/r/20220502175342.20296-1-rdunlap@infradead.org Fixes: 82cae269cfa9 ("fs/ntfs3: Add initialization of super block") Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Reported-by: syzbot+1631f09646bc214d2e76@syzkaller.appspotmail.com Reviewed-by: Namjae Jeon <linkinjeon@kernel.org> Cc: Konstantin Komarov <almaz.alexandrovich@paragon-software.com> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: Kari Argillander <kari.argillander@stargateuniverse.net> Cc: Namjae Jeon <linkinjeon@kernel.org> Cc: Matthew Wilcox <willy@infradead.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
lizhe [Fri, 13 May 2022 03:38:36 +0000 (20:38 -0700)]
kernel/crash_core.c: remove redundant check of ck_cmdline
At the end of get_last_crashkernel(), the judgement of ck_cmdline is
obviously unnecessary and causes redundance, let's clean it up.
Link: https://lkml.kernel.org/r/20220506104116.259323-1-sensor1010@163.com Signed-off-by: lizhe <sensor1010@163.com> Acked-by: Baoquan He <bhe@redhat.com> Acked-by: Philipp Rudo <prudo@redhat.com> Cc: Vivek Goyal <vgoyal@redhat.com> Cc: Dave Young <dyoung@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Anusha Srivatsa [Wed, 11 May 2022 00:08:47 +0000 (17:08 -0700)]
drm/i915/dmc: Add MMIO range restrictions
Bspec has added some steps that check forDMC MMIO range before
programming them
v2: Fix for CI
v3: move register defines to .h (Anusha)
- Check MMIO restrictions per pipe
- Add MMIO restricton for v1 dmc header as well (Lucas)
v4: s/_PICK/_PICK_EVEN and use it only for Pipe DMC scenario.
- clean up sanity check logic.(Lucas)
- Add MMIO range for RKL as well.(Anusha)
v5: Use DISPLAY_VER instead of per platform check (Lucas)
====================
net: inet: Retire port only listening_hash
This series is to retire the port only listening_hash.
The listen sk is currently stored in two hash tables,
listening_hash (hashed by port) and lhash2 (hashed by port and address).
After commit 0ee58dad5b06 ("net: tcp6: prefer listeners bound to an address")
and commit d9fbc7f6431f ("net: tcp: prefer listeners bound to an address"),
the TCP-SYN lookup fast path does not use listening_hash.
The commit 05c0b35709c5 ("tcp: seq_file: Replace listening_hash with lhash2")
also moved the seq_file (/proc/net/tcp) iteration usage from
listening_hash to lhash2.
There are still a few listening_hash usages left.
One of them is inet_reuseport_add_sock() which uses the listening_hash
to search a listen sk during the listen() system call. This turns
out to be very slow on use cases that listen on many different
VIPs at a popular port (e.g. 443). [ On top of the slowness in
adding to the tail in the IPv6 case ]. A latter patch has a
selftest to demonstrate this case.
This series takes this chance to move all remaining listening_hash
usages to lhash2 and then retire listening_hash.
====================
Martin KaFai Lau [Thu, 12 May 2022 00:06:11 +0000 (17:06 -0700)]
net: selftests: Stress reuseport listen
This patch adds a test that has 300 VIPs listening on port 443.
Each VIP:443 will have 80 listening socks by using SO_REUSEPORT.
Thus, it will have 24000 listening socks.
Before removing the port only listening_hash, all socks will be in the
same port 443 bucket and inet_reuseport_add_sock() spends much time to
walk through the bucket. After removing the port only listening_hash
and move all usage to the port+addr lhash2, each bucket in the
ideal case has 80 sk which is much smaller than before.
Here is the test result from a qemu:
Before: listen 24000 socks took 210.210485362 (~210s)
After: listen 24000 socks took 0.207173 (~210ms)
Signed-off-by: Martin KaFai Lau <kafai@fb.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Martin KaFai Lau [Thu, 12 May 2022 00:06:05 +0000 (17:06 -0700)]
net: inet: Retire port only listening_hash
The listen sk is currently stored in two hash tables,
listening_hash (hashed by port) and lhash2 (hashed by port and address).
After commit 0ee58dad5b06 ("net: tcp6: prefer listeners bound to an address")
and commit d9fbc7f6431f ("net: tcp: prefer listeners bound to an address"),
the TCP-SYN lookup fast path does not use listening_hash.
The commit 05c0b35709c5 ("tcp: seq_file: Replace listening_hash with lhash2")
also moved the seq_file (/proc/net/tcp) iteration usage from
listening_hash to lhash2.
There are still a few listening_hash usages left.
One of them is inet_reuseport_add_sock() which uses the listening_hash
to search a listen sk during the listen() system call. This turns
out to be very slow on use cases that listen on many different
VIPs at a popular port (e.g. 443). [ On top of the slowness in
adding to the tail in the IPv6 case ]. The latter patch has a
selftest to demonstrate this case.
This patch takes this chance to move all remaining listening_hash
usages to lhash2 and then retire listening_hash.
Since most changes need to be done together, it is hard to cut
the listening_hash to lhash2 switch into small patches. The
changes in this patch is highlighted here for the review
purpose.
1. Because of the listening_hash removal, lhash2 can use the
sk->sk_nulls_node instead of the icsk->icsk_listen_portaddr_node.
This will also keep the sk_unhashed() check to work as is
after stop adding sk to listening_hash.
The union is removed from inet_listen_hashbucket because
only nulls_head is needed.
2. icsk->icsk_listen_portaddr_node and its helpers are removed.
3. The current lhash2 users needs to iterate with sk_nulls_node
instead of icsk_listen_portaddr_node.
One case is in the inet[6]_lhash2_lookup().
Another case is the seq_file iterator in tcp_ipv4.c.
One thing to note is sk_nulls_next() is needed
because the old inet_lhash2_for_each_icsk_continue()
does a "next" first before iterating.
4. Move the remaining listening_hash usage to lhash2
inet_reuseport_add_sock() which this series is
trying to improve.
inet_diag.c and mptcp_diag.c are the final two
remaining use cases and is moved to lhash2 now also.
Signed-off-by: Martin KaFai Lau <kafai@fb.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Martin KaFai Lau [Thu, 12 May 2022 00:05:58 +0000 (17:05 -0700)]
net: inet: Open code inet_hash2 and inet_unhash2
This patch folds lhash2 related functions into __inet_hash and
inet_unhash. This will make the removal of the listening_hash
in a latter patch easier to review.
First, this patch folds inet_hash2 into __inet_hash.
For unhash, the current call sequence is like
inet_unhash() => __inet_unhash() => inet_unhash2().
The specific testing cases in __inet_unhash() are mostly related
to TCP_LISTEN sk and its caller inet_unhash() already has
the TCP_LISTEN test, so this patch folds both __inet_unhash() and
inet_unhash2() into inet_unhash().
Note that all listening_hash users also have lhash2 initialized,
so the !h->lhash2 check is no longer needed.
Signed-off-by: Martin KaFai Lau <kafai@fb.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Martin KaFai Lau [Thu, 12 May 2022 00:05:52 +0000 (17:05 -0700)]
net: inet: Remove count from inet_listen_hashbucket
After commit 0ee58dad5b06 ("net: tcp6: prefer listeners bound to an address")
and commit d9fbc7f6431f ("net: tcp: prefer listeners bound to an address"),
the count is no longer used. This patch removes it.
Signed-off-by: Martin KaFai Lau <kafai@fb.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
====================
Make sfc-siena.ko specific to Siena
This series is a follow-up to the one titled "Move Siena into
a separate subdirectory".
It enhances the new sfc-siena.ko module to differentiate it from sfc.ko.
Patches
Patches 1-5 create separate Kconfig options for Siena, and adjusts the
various names used for work items and directories.
Patch 6 reinstates SRIOV functionality in sfc-siena.ko.
Testing
Various build tests were done such as allyesconfig, W=1 and sparse.
The new sfc-siena.ko and sfc.ko modules were tested on a machine with NICs
for both modules in them.
Inserting the updated sfc.ko and the new sfc-siena.ko modules at the same
time works, and no work items and directories exist with the same name.
====================
Martin Habets [Wed, 11 May 2022 16:20:25 +0000 (17:20 +0100)]
sfc/siena: Reinstate SRIOV init/fini function calls
They were removed in the first series since they were not used for EF10.
Put that code back for Siena, with the prototypes in siena_sriov.h
since that file is a more applicable place for it.
Reported-by: kernel test robot <lkp@intel.com> Signed-off-by: Martin Habets <habetsm.xilinx@gmail.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Martin Habets [Wed, 11 May 2022 16:20:01 +0000 (17:20 +0100)]
sfc/siena: Make MCDI logging support specific for Siena
Add a Siena Kconfig option and use it in stead of the sfc one.
Rename the internal variable for the 'mcdi_logging_default' module
parameter to avoid a naming conflict with the one in sfc.ko.
Signed-off-by: Martin Habets <habetsm.xilinx@gmail.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch set represents preparation for further work. It adds an
"index" field to struct ocelot_port, and populates it from the Felix DSA
driver and Ocelot switchdev driver.
The users of struct ocelot_port :: index are the same users as those of
struct ocelot_port_private :: chip_port.
====================
Vladimir Oltean [Wed, 11 May 2022 10:06:37 +0000 (13:06 +0300)]
net: mscc: ocelot: move ocelot_port_private :: chip_port to ocelot_port :: index
Currently the ocelot switch lib is unaware of the index of a struct
ocelot_port, since that is kept in the encapsulating structures of outer
drivers (struct dsa_port :: index, struct ocelot_port_private :: chip_port).
With the upcoming increase in complexity associated with assigning DSA
tag_8021q CPU ports to certain user ports, it becomes necessary for the
switch lib to be able to retrieve the index of a certain ocelot_port.
Therefore, introduce a new u8 to ocelot_port (same size as the chip_port
used by the ocelot switchdev driver) and rework the existing code to
populate and use it.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
====================
DSA changes for multiple CPU ports (part 1)
I am trying to enable the second internal port pair from the NXP LS1028A
Felix switch for DSA-tagged traffic via "ocelot-8021q". This series
represents part 1 (of an unknown number) of that effort.
It does some preparation work, like managing host flooding in DSA via a
dedicated method, and removing the CPU port as argument from the tagging
protocol change procedure.
In terms of driver-specific changes, it reworks the 2 tag protocol
implementations in the Felix driver to have a structured data format.
It enables host flooding towards all tag_8021q CPU ports. It dynamically
updates the tag_8021q CPU port used for traps. It also fixes a bug
introduced by a previous refactoring/oversimplification commit in
net-next.
====================
Vladimir Oltean [Wed, 11 May 2022 09:50:20 +0000 (12:50 +0300)]
net: dsa: felix: reimplement tagging protocol change with function pointers
The error handling for the current tagging protocol change procedure is
a bit brittle (we dismantle the previous tagging protocol entirely
before setting up the new one). By identifying which parts of a tagging
protocol are unique to itself and which parts are shared with the other,
we can implement a protocol change procedure where error handling is a
bit more robust, because we start setting up the new protocol first, and
tear down the old one only after the setup of the specific and shared
parts succeeded.
The protocol change is a bit too open-coded too, in the area of
migrating host flood settings and MDBs. By identifying what differs
between tagging protocols (the forwarding masks for host flooding) we
can implement a more straightforward migration procedure which is
handled in the shared portion of the protocol change, rather than
individually by each protocol.
Therefore, a more structured approach calls for the introduction of a
structure of function pointers per tagging protocol. This covers setup,
teardown and the host forwarding mask. In the future it will also cover
how to prepare for a new DSA master.
The initial tagging protocol setup (at driver probe time) and the final
teardown (at driver removal time) are also adapted to call into the
structured methods of the specific protocol in current use. This is
especially relevant for teardown, where we previously called
felix_del_tag_protocol() only for the first CPU port. But by not
specifying which CPU port this is for, we gain more flexibility to
support multiple CPU ports in the future.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Vladimir Oltean [Wed, 11 May 2022 09:50:19 +0000 (12:50 +0300)]
net: dsa: felix: dynamically determine tag_8021q CPU port for traps
Ocelot switches support a single active CPU port at a time (at least as
a trapping destination, i.e. for control traffic). This is true
regardless of whether we are using the native copy-to-CPU-port-module
functionality, or a redirect action towards the software-defined
tag_8021q CPU port.
Currently we assume that the trapping destination in tag_8021q mode is
the first CPU port, yet in the future we may want to migrate the user
ports to the second CPU port.
For that to work, we need to make sure that the tag_8021q trapping
destination is a CPU port that is active, i.e. is used by at least some
user port on which the trap was added. Otherwise, we may end up
redirecting the traffic to a CPU port which isn't even up.
Note that due to the current design where we simply choose the CPU port
of the first port from the trap's ingress port mask, it may be that a
CPU port absorbes control traffic from user ports which aren't affine to
it as per user space's request. This isn't ideal, but is the lesser of
two evils. Following the user-configured affinity for traps would mean
that we can no longer reuse a single TCAM entry for multiple traps,
which is what we actually do for e.g. PTP. Either we duplicate and
deduplicate TCAM entries on the fly when user-to-CPU-port mappings
change (which is unnecessarily complicated), or we redirect trapped
traffic to all tag_8021q CPU ports if multiple such ports are in use.
The latter would have actually been nice, if it actually worked, but it
doesn't, since a OCELOT_MASK_MODE_REDIRECT action towards multiple ports
would not take PGID_SRC into consideration, and it would just duplicate
the packet towards each (CPU) port, leading to duplicates in software.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Vladimir Oltean [Wed, 11 May 2022 09:50:18 +0000 (12:50 +0300)]
net: dsa: remove port argument from ->change_tag_protocol()
DSA has not supported (and probably will not support in the future
either) independent tagging protocols per CPU port.
Different switch drivers have different requirements, some may need to
replicate some settings for each CPU port, some may need to apply some
settings on a single CPU port, while some may have to configure some
global settings and then some per-CPU-port settings.
In any case, the current model where DSA calls ->change_tag_protocol for
each CPU port turns out to be impractical for drivers where there are
global things to be done. For example, felix calls dsa_tag_8021q_register(),
which makes no sense per CPU port, so it suppresses the second call.
Let drivers deal with replication towards all CPU ports, and remove the
CPU port argument from the function prototype.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Acked-by: Luiz Angelo Daros de Luca <luizluca@gmail.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Vladimir Oltean [Wed, 11 May 2022 09:50:17 +0000 (12:50 +0300)]
net: dsa: felix: manage host flooding using a specific driver callback
At the time - commit 7569459a52c9 ("net: dsa: manage flooding on the CPU
ports") - not introducing a dedicated switch callback for host flooding
made sense, because for the only user, the felix driver, there was
nothing different to do for the CPU port than set the flood flags on the
CPU port just like on any other bridge port.
There are 2 reasons why this approach is not good enough, however.
(1) Other drivers, like sja1105, support configuring flooding as a
function of {ingress port, egress port}, whereas the DSA
->port_bridge_flags() function only operates on an egress port.
So with that driver we'd have useless host flooding from user ports
which don't need it.
(2) Even with the felix driver, support for multiple CPU ports makes it
difficult to piggyback on ->port_bridge_flags(). The way in which
the felix driver is going to support host-filtered addresses with
multiple CPU ports is that it will direct these addresses towards
both CPU ports (in a sort of multicast fashion), then restrict the
forwarding to only one of the two using the forwarding masks.
Consequently, flooding will also be enabled towards both CPU ports.
However, ->port_bridge_flags() gets passed the index of a single CPU
port, and that leaves the flood settings out of sync between the 2
CPU ports.
This is to say, it's better to have a specific driver method for host
flooding, which takes the user port as argument. This solves problem (1)
by allowing the driver to do different things for different user ports,
and problem (2) by abstracting the operation and letting the driver do
whatever, rather than explicitly making the DSA core point to the CPU
port it thinks needs to be touched.
This new method also creates a problem, which is that cross-chip setups
are not handled. However I don't have hardware right now where I can
test what is the proper thing to do, and there isn't hardware compatible
with multi-switch trees that supports host flooding. So it remains a
problem to be tackled in the future.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Vladimir Oltean [Wed, 11 May 2022 09:50:16 +0000 (12:50 +0300)]
net: dsa: introduce the dsa_cpu_ports() helper
Similar to dsa_user_ports() which retrieves a port mask of all user
ports, introduce dsa_cpu_ports() which retrieves the mask of all CPU
ports of a switch.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Vladimir Oltean [Wed, 11 May 2022 09:50:15 +0000 (12:50 +0300)]
net: dsa: felix: bring the NPI port indirection for host flooding to surface
For symmetry with host FDBs and MDBs where the indirection is now
handled outside the ocelot switch lib, do the same for bridge port
flags (unicast/multicast/broadcast flooding).
The only caller of the ocelot switch lib which uses the NPI port is the
Felix DSA driver.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Vladimir Oltean [Wed, 11 May 2022 09:50:14 +0000 (12:50 +0300)]
net: dsa: felix: bring the NPI port indirection for host MDBs to surface
For symmetry with host FDBs where the indirection is now handled outside
the ocelot switch lib, do the same for host MDB entries. The only caller
of the ocelot switch lib which uses the NPI port is the Felix DSA driver.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Vladimir Oltean [Wed, 11 May 2022 09:50:13 +0000 (12:50 +0300)]
net: dsa: felix: program host FDB entries towards PGID_CPU for tag_8021q too
I remembered why we had the host FDB migration procedure in place.
It is true that host FDB entry migration can be done by changing the
value of PGID_CPU, but the problem is that only host FDB entries learned
while operating in NPI mode go to PGID_CPU. When the CPU port operates
in tag_8021q mode, the FDB entries are learned towards the unicast PGID
equal to the physical port number of this CPU port, bypassing the
PGID_CPU indirection.
So host FDB entries learned in tag_8021q mode are not migrated any
longer towards the NPI port.
Fix this by extracting the NPI port -> PGID_CPU redirection from the
ocelot switch lib, moving it to the Felix DSA driver, and applying it
for any CPU port regardless of its kind (NPI or tag_8021q).
Fixes: a51c1c3f3218 ("net: dsa: felix: stop migrating FDBs back and forth on tag proto change") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Horatiu Vultur [Wed, 11 May 2022 20:40:59 +0000 (22:40 +0200)]
net: lan966x: Fix use of pointer after being freed
The smatch found the following warning:
drivers/net/ethernet/microchip/lan966x/lan966x_fdma.c:736 lan966x_fdma_reload()
warn: 'rx_dcbs' was already freed.
This issue can happen when changing the MTU on one of the ports and once
the RX buffers are allocated and then the TX buffer allocation fails.
In that case the RX buffers should not be restore. This fix this issue
such that the RX buffers will not be restored if the TX buffers failed
to be allocated.
Jakub Kicinski [Wed, 11 May 2022 17:23:05 +0000 (10:23 -0700)]
skbuff: replace a BUG_ON() with the new DEBUG_NET_WARN_ON_ONCE()
Very few drivers actually have Kconfig knobs for adding
-DDEBUG. 8 according to a quick grep, while there are
93 users of skb_checksum_none_assert(). Switch to the
new DEBUG_NET_WARN_ON_ONCE() to catch bad skbs.
The driver currently has three interrupt counters,
which are incremented every time each interrupt handler
executes. These driver-managed counters are not
necessary as the kernel already has logic that manages
interrupt counts and exposes them via /proc/interrupts.
This patch removes the driver-managed counters.
Build issue in drivers/net/ethernet/sfc/ptp.c 54fccfdd7c66 ("sfc: efx_default_channel_type APIs can be static") 49e6123c65da ("net: sfc: fix memory leak due to ptp channel")
https://lore.kernel.org/all/20220510130556.52598fe2@canb.auug.org.au/
Mimi Zohar [Thu, 12 May 2022 22:42:08 +0000 (18:42 -0400)]
Merge branch 'next-integrity.fsverity-v9' into next-integrity
Support for including fs-verity file digests and signatures in the IMA
measurement list as well as verifying the fs-verity file digest based
signatures.
PCI: cadence: Clear FLR in device capabilities register
Clear FLR (Function Level Reset) from device capabilities
registers for all physical functions.
During FLR, the Margining Lane Status and Margining Lane Control
registers should not be reset, as per PCIe specification.
However, the controller incorrectly resets these registers upon FLR.
This causes PCISIG compliance FLR test to fail. Hence preventing
all functions from advertising FLR support if flag quirk_disable_flr
is set.
This enables the Controller [RP] to automatically respond with
Response/ResponseD messages if CDNS_PCIE_LM_TPM_CTRL_PTMRSEN
and PCI_PTM_CTRL_ENABLE bits are both set.
Arnd Bergmann [Thu, 12 May 2022 20:33:16 +0000 (22:33 +0200)]
Merge tag 'v5.18-rockchip-dtsfixes1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into arm/fixes
Fixes for the mass-production version of BananaPi R2-Pro.
The mass market version received some changes compared to
preproduction versions and especially the io-domain setting
could affect the lifespan of the board if the wrong dt
gets booted on it.
* tag 'v5.18-rockchip-dtsfixes1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
arm64: dts: rockchip: Add gmac1 and change network settings of bpi-r2-pro
arm64: dts: rockchip: Change io-domains of bpi-r2-pro
Josh Poimboeuf [Thu, 12 May 2022 19:05:27 +0000 (12:05 -0700)]
scripts/faddr2line: Fix overlapping text section failures
There have been some recent reports of faddr2line failures:
$ scripts/faddr2line sound/soundcore.ko sound_devnode+0x5/0x35
bad symbol size: base: 0x0000000000000000 end: 0x0000000000000000
$ ./scripts/faddr2line vmlinux.o enter_from_user_mode+0x24
bad symbol size: base: 0x0000000000005fe0 end: 0x0000000000005fe0
The problem is that faddr2line is based on 'nm', which has a major
limitation: it doesn't know how to distinguish between different text
sections. So if an offset exists in multiple text sections in the
object, it may fail.
Rewrite faddr2line to be section-aware, by basing it on readelf.
- wifi: iwlwifi: iwl-dbg: use del_timer_sync() before freeing
- wifi: ath11k: reduce the wait time of 11d scan and hw scan while
adding an interface
- mac80211: fix rx reordering with non explicit / psmp ack policy
- mac80211: reset MBSSID parameters upon connection
- nl80211: fix races in nl80211_set_tx_bitrate_mask()
- tls: fix context leak on tls_device_down
- sched: act_pedit: really ensure the skb is writable
- batman-adv: don't skb_split skbuffs with frag_list
- eth: ocelot: fix various issues with TC actions (null-deref; bad
stats; ineffective drops; ineffective filter removal)"
* tag 'net-5.18-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (61 commits)
tls: Fix context leak on tls_device_down
net: sfc: ef10: fix memory leak in efx_ef10_mtd_probe()
net/smc: non blocking recvmsg() return -EAGAIN when no data and signal_pending
net: dsa: bcm_sf2: Fix Wake-on-LAN with mac_link_down()
mlxsw: Avoid warning during ip6gre device removal
net: bcmgenet: Check for Wake-on-LAN interrupt probe deferral
net: ethernet: mediatek: ppe: fix wrong size passed to memset()
Bluetooth: Fix the creation of hdev->name
i40e: i40e_main: fix a missing check on list iterator
net/sched: act_pedit: really ensure the skb is writable
s390/lcs: fix variable dereferenced before check
s390/ctcm: fix potential memory leak
s390/ctcm: fix variable dereferenced before check
net: atlantic: verify hw_head_ lies within TX buffer ring
net: atlantic: add check for MAX_SKB_FRAGS
net: atlantic: reduce scope of is_rsc_complete
net: atlantic: fix "frag[0] not initialized"
net: stmmac: fix missing pci_disable_device() on error in stmmac_pci_probe()
net: phy: micrel: Fix incorrect variable type in micrel
decnet: Use container_of() for struct dn_neigh casts
...
i915/guc/reset: Make __guc_reset_context aware of guilty engines
There are 2 ways an engine can get reset in i915 and the method of reset
affects how KMD labels a context as guilty/innocent.
(1) GuC initiated engine-reset: GuC resets a hung engine and notifies
KMD. The context that hung on the engine is marked guilty and all other
contexts are innocent. The innocent contexts are resubmitted.
(2) GT based reset: When an engine heartbeat fails to tick, KMD
initiates a gt/chip reset. All active contexts are marked as guilty and
discarded.
In order to correctly mark the contexts as guilty/innocent, pass a mask
of engines that were reset to __guc_reset_context.
Linus Torvalds [Thu, 12 May 2022 17:42:56 +0000 (10:42 -0700)]
Merge branch 'for-5.18-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup
Pull cgroup fix from Tejun Heo:
"Waiman's fix for a cgroup2 cpuset bug where it could miss nodes which
were hot-added"
* 'for-5.18-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
cgroup/cpuset: Remove cpus_allowed/mems_allowed setup in cpuset_init_smp()
Masahiro Yamada [Thu, 5 May 2022 03:52:11 +0000 (12:52 +0900)]
module: do not binary-search in __ksymtab_gpl if fsa->gplok is false
Currently, !fsa->gplok && syms->license == GPL_ONLY) is checked after
bsearch() succeeds.
It is meaningless to do the binary search in the GPL symbol table when
fsa->gplok is false because we know find_exported_symbol_in_section()
will fail anyway.
This check should be done before bsearch().
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org> Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
module: show disallowed symbol name for inherit_taint()
The error log for inherit_taint() doesn't really help to find the
symbol which violates GPL rules.
For example,
if a module has 300 symbol and includes 50 disallowed symbols,
the log only shows the content below and we have no idea what symbol is.
AAA: module using GPL-only symbols uses symbols from proprietary module BBB.
It's hard for user who doesn't really know how the symbol was parsing.
This patch add symbol name to tell the offending symbols explicitly.
AAA: module using GPL-only symbols uses symbols SSS from proprietary module BBB.
Signed-off-by: Lecopzer Chen <lecopzer.chen@mediatek.com> Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
Aaron Tomlin [Mon, 2 May 2022 20:52:52 +0000 (21:52 +0100)]
module: Introduce module unload taint tracking
Currently, only the initial module that tainted the kernel is
recorded e.g. when an out-of-tree module is loaded.
The purpose of this patch is to allow the kernel to maintain a record of
each unloaded module that taints the kernel. So, in addition to
displaying a list of linked modules (see print_modules()) e.g. in the
event of a detected bad page, unloaded modules that carried a taint/or
taints are displayed too. A tainted module unload count is maintained.
The number of tracked modules is not fixed. This feature is disabled by
default.
Signed-off-by: Aaron Tomlin <atomlin@redhat.com> Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
Aaron Tomlin [Mon, 2 May 2022 20:51:04 +0000 (21:51 +0100)]
module: Move module_assert_mutex_or_preempt() to internal.h
No functional change.
This patch migrates module_assert_mutex_or_preempt() to internal.h.
So, the aforementiond function can be used outside of main/or core
module code yet will remain restricted for internal use only.
Signed-off-by: Aaron Tomlin <atomlin@redhat.com> Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
Aaron Tomlin [Mon, 2 May 2022 20:51:03 +0000 (21:51 +0100)]
module: Make module_flags_taint() accept a module's taints bitmap and usable outside core code
No functional change.
The purpose of this patch is to modify module_flags_taint() to accept
a module's taints bitmap as a parameter and modifies all users
accordingly. Furthermore, it is now possible to access a given
module's taint flags data outside of non-essential code yet does
remain for internal use only.
This is in preparation for module unload taint tracking support.
Signed-off-by: Aaron Tomlin <atomlin@redhat.com> Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
In commit ca321ec74322 ("module.h: allow #define strings to work with
MODULE_IMPORT_NS") I fixed up the MODULE_IMPORT_NS() macro to allow
defined strings to work with it. Unfortunatly I did it in a two-stage
process, when it could just be done with the __stringify() macro as
pointed out by Masahiro Yamada.
Clean this up to only be one macro instead of two steps to achieve the
same end result.
Fixes: ca321ec74322 ("module.h: allow #define strings to work with MODULE_IMPORT_NS") Reported-by: Masahiro Yamada <masahiroy@kernel.org> Cc: Luis Chamberlain <mcgrof@kernel.org> Cc: Jessica Yu <jeyu@kernel.org> Cc: Matthias Maennich <maennich@google.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
Linus Torvalds [Thu, 12 May 2022 17:21:44 +0000 (10:21 -0700)]
Merge tag 'fixes_for_v5.18-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs
Pull fs fixes from Jan Kara:
"Three fixes that I'd still like to get to 5.18:
- add a missing sanity check in the fanotify FAN_RENAME feature
(added in 5.17, let's fix it before it gets wider usage in
userspace)
- udf fix for recently introduced filesystem corruption issue
- writeback fix for a race in inode list handling that can lead to
delayed writeback and possible dirty throttling stalls"
* tag 'fixes_for_v5.18-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
udf: Avoid using stale lengthOfImpUse
writeback: Avoid skipping inode writeback
fanotify: do not allow setting dirent events in mask of non-dir
After:
$ ./tools/testing/kunit/kunit.py parse /dev/null
...
[ERROR] Test <missing>: could not find any KTAP output!
This error message gets printed out when extract_tap_output() yielded no
lines. So while it could be because of malformed KTAP output from KUnit,
it could also be due to not having any KTAP output at all.
Try and make the error message here more clear.
Signed-off-by: Daniel Latypov <dlatypov@google.com> Reviewed-by: David Gow <davidgow@google.com> Reviewed-by: Brendan Higgins <brendanhiggins@google.com> Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Daniel Latypov [Thu, 12 May 2022 14:25:55 +0000 (07:25 -0700)]
kunit: tool: stop using a shell to run kernel under QEMU
Note: this potentially breaks custom qemu_configs if people are using
them! But the fix for them is simple, don't specify multiple arguments
in one string and don't add on a redundant ''.
It feels a bit iffy to be using a shell in the first place.
There's the usual shenanigans where people could pass in arbitrary shell
commands via --kernel_arg (since we're just adding '' around the
kernel_cmdline) or via a custom qemu_config.
This isn't too much of a concern given the nature of this script (and
the qemu_config file is in python, you can do w/e you want already).
But it does have some other drawbacks.
One example of a kunit-specific pain point:
If the relevant qemu binary is missing, we get output like this:
> /bin/sh: line 1: qemu-system-aarch64: command not found
This in turn results in our KTAP parser complaining about
missing/invalid KTAP, but we don't directly show the error!
It's even more annoying to debug when you consider --raw_output only
shows KUnit output by default, i.e. you need --raw_output=all to see it.
Whereas directly invoking the binary, Python will raise a
FileNotFoundError for us, which is a noisier but more clear.
Making this change requires
* splitting parameters like ['-m 256'] into ['-m', '256'] in
kunit/qemu_configs/*.py
* change [''] to [] in kunit/qemu_configs/*.py since otherwise
QEMU fails w/ 'Device needs media, but drive is empty'
* dropping explicit quoting of the kernel cmdline
* using shlex.quote() when we print what command we're running
so the user can copy-paste and run it
Even with our current set of statuses, the output is a bit verbose.
It could get worse in the future if we add more (e.g. timeout, kasan).
Let's only print the relevant ones.
I had previously been sympathetic to the argument that always
printing out all the statuses would make it easier to parse results.
But now we have commit acd8e8407b8f ("kunit: Print test statistics on
failure"), there are test counts printed out in the raw output.
We don't currently print out an overall total across all suites, but it
would be easy to add, if we see a need for that.
Signed-off-by: Daniel Latypov <dlatypov@google.com> Co-developed-by: David Gow <davidgow@google.com> Signed-off-by: David Gow <davidgow@google.com> Reviewed-by: Brendan Higgins <brendanhiggins@google.com> Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Daniel Latypov [Wed, 11 May 2022 21:16:26 +0000 (14:16 -0700)]
kunit: bail out of test filtering logic quicker if OOM
When filtering what tests to run (suites and/or cases) via
kunit.filter_glob (e.g. kunit.py run <glob>), we allocate copies of
suites.
These allocations can fail, and we largely don't handle that.
Note: realistically, this probably doesn't matter much.
We're not allocating much memory and this happens early in boot, so if
we can't do that, then there's likely far bigger problems.
This patch makes us immediately bail out from the top-level function
(kunit_filter_suites) with -ENOMEM if any of the underlying kmalloc()
calls return NULL.
Implementation note: we used to return NULL pointers from some functions
to indicate either that all suites/tests were filtered out or there was
an error allocating the new array.
We'll log a short error in this case and not run any tests or print a
TAP header. From a kunit.py user's perspective, they'll get a message
about missing/invalid TAP output and have to dig into the test.log to
see it. Since hitting this error seems so unlikely, it's probably fine
to not invent a way to plumb this error message more visibly.
See also: https://lore.kernel.org/linux-kselftest/20220329103919.2376818-1-lv.ruyi@zte.com.cn/
Daniel Latypov [Tue, 5 Apr 2022 19:06:19 +0000 (12:06 -0700)]
lib/Kconfig.debug: change KUnit tests to default to KUNIT_ALL_TESTS
This is in line with Documentation/dev-tools/kunit/style.rst.
Some of these tests predate that so they don't follow this convention.
With this and commit b0841b51cac9 ("kunit: arch/um/configs: Enable
KUNIT_ALL_TESTS by default"), kunit.py will now run these tests by
default. This hopefully makes it easier to run and maintain the tests.
If any of these were to start failing, people would notice much quicker.
Note: this commit doesn't update LINEAR_RANGES_TEST since that would
select its dependency (LINEAR_RANGES). We don't want KUNIT_ALL_TESTS
to enable anything other than test kconfigs.
David Gow [Sat, 2 Apr 2022 04:35:30 +0000 (12:35 +0800)]
kunit: Rework kunit_resource allocation policy
KUnit's test-managed resources can be created in two ways:
- Using the kunit_add_resource() family of functions, which accept a
struct kunit_resource pointer, typically allocated statically or on
the stack during the test.
- Using the kunit_alloc_resource() family of functions, which allocate a
struct kunit_resource using kzalloc() behind the scenes.
Both of these families of functions accept a 'free' function to be
called when the resource is finally disposed of.
At present, KUnit will kfree() the resource if this 'free' function is
specified, and will not if it is NULL. However, this can lead
kunit_alloc_resource() to leak memory (if no 'free' function is passed
in), or kunit_add_resource() to incorrectly kfree() memory which was
allocated by some other means (on the stack, as part of a larger
allocation, etc), if a 'free' function is provided.
Instead, always kfree() if the resource was allocated with
kunit_alloc_resource(), and never kfree() if it was passed into
kunit_add_resource() by the user. (If the user of kunit_add_resource()
wishes the resource be kfree()ed, they can call kfree() on the resource
from within the 'free' function.
This is implemented by adding a 'should_free' member to
struct kunit_resource and setting it appropriately. To facilitate this,
the various resource add/alloc functions have been refactored somewhat,
making them all call a __kunit_add_resource() helper after setting the
'should_free' member appropriately. In the process, all other functions
have been made static inline functions.
Signed-off-by: David Gow <davidgow@google.com> Tested-by: Daniel Latypov <dlatypov@google.com> Reviewed-by: Brendan Higgins <brendanhiggins@google.com> Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Eric Biggers [Sun, 1 May 2022 05:08:52 +0000 (22:08 -0700)]
f2fs: reject test_dummy_encryption when !CONFIG_FS_ENCRYPTION
There is no good reason to allow this mount option when the kernel isn't
configured with encryption support. Since this option is only for
testing, we can just fix this; we don't really need to worry about
breaking anyone who might be counting on this option being ignored.
Signed-off-by: Eric Biggers <ebiggers@google.com> Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Current atomic write has three major issues like below.
- keeps the updates in non-reclaimable memory space and they are even
hard to be migrated, which is not good for contiguous memory
allocation.
- disk spaces used for atomic files cannot be garbage collected, so
this makes it difficult for the filesystem to be defragmented.
- If atomic write operations hit the threshold of either memory usage
or garbage collection failure count, All the atomic write operations
will fail immediately.
To resolve the issues, I will keep a COW inode internally for all the
updates to be flushed from memory, when we need to flush them out in a
situation like high memory pressure. These COW inodes will be tagged
as orphan inodes to be reclaimed in case of sudden power-cut or system
failure during atomic writes.
Signed-off-by: Daeho Jeong <daehojeong@google.com> Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
The commit cited below claims to fix a use-after-free condition after
tls_device_down. Apparently, the description wasn't fully accurate. The
context stayed alive, but ctx->netdev became NULL, and the offload was
torn down without a proper fallback, so a bug was present, but a
different kind of bug.
Due to misunderstanding of the issue, the original patch dropped the
refcount_dec_and_test line for the context to avoid the alleged
premature deallocation. That line has to be restored, because it matches
the refcount_inc_not_zero from the same function, otherwise the contexts
that survived tls_device_down are leaked.
This patch fixes the described issue by restoring refcount_dec_and_test.
After this change, there is no leak anymore, and the fallback to
software kTLS still works.
Fixes: c55dcdd435aa ("net/tls: Fix use-after-free after the TLS device goes down and up") Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com> Reviewed-by: Tariq Toukan <tariqt@nvidia.com> Link: https://lore.kernel.org/r/20220512091830.678684-1-maximmi@nvidia.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Taehee Yoo [Thu, 12 May 2022 05:47:09 +0000 (05:47 +0000)]
net: sfc: ef10: fix memory leak in efx_ef10_mtd_probe()
In the NIC ->probe() callback, ->mtd_probe() callback is called.
If NIC has 2 ports, ->probe() is called twice and ->mtd_probe() too.
In the ->mtd_probe(), which is efx_ef10_mtd_probe() it allocates and
initializes mtd partiion.
But mtd partition for sfc is shared data.
So that allocated mtd partition data from last called
efx_ef10_mtd_probe() will not be used.
Therefore it must be freed.
But it doesn't free a not used mtd partition data in efx_ef10_mtd_probe().
Guangguan Wang [Thu, 12 May 2022 03:08:20 +0000 (11:08 +0800)]
net/smc: non blocking recvmsg() return -EAGAIN when no data and signal_pending
Non blocking sendmsg will return -EAGAIN when any signal pending
and no send space left, while non blocking recvmsg return -EINTR
when signal pending and no data received. This may makes confused.
As TCP returns -EAGAIN in the conditions described above. Align the
behavior of smc with TCP.
Fixes: 846e344eb722 ("net/smc: add receive timeout check") Signed-off-by: Guangguan Wang <guangguan.wang@linux.alibaba.com> Reviewed-by: Tony Lu <tonylu@linux.alibaba.com> Acked-by: Karsten Graul <kgraul@linux.ibm.com> Link: https://lore.kernel.org/r/20220512030820.73848-1-guangguan.wang@linux.alibaba.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Florian Fainelli [Thu, 12 May 2022 02:17:31 +0000 (19:17 -0700)]
net: dsa: bcm_sf2: Fix Wake-on-LAN with mac_link_down()
After commit 2d1f90f9ba83 ("net: dsa/bcm_sf2: fix incorrect usage of
state->link") the interface suspend path would call our mac_link_down()
call back which would forcibly set the link down, thus preventing
Wake-on-LAN packets from reaching our management port.
Fix this by looking at whether the port is enabled for Wake-on-LAN and
not clearing the link status in that case to let packets go through.
Chunfeng Yun [Thu, 12 May 2022 06:49:31 +0000 (14:49 +0800)]
usb: xhci-mtk: remove bandwidth budget table
The bandwidth budget table is introduced to trace ideal bandwidth used
by each INT/ISOC endpoint, but in fact the endpoint may consume more
bandwidth and cause data transfer error, so it's better to leave some
margin. Obviously it's difficult to find the best margin for all cases,
instead take use of the worst-case scenario.
Chunfeng Yun [Thu, 12 May 2022 06:49:30 +0000 (14:49 +0800)]
usb: xhci-mtk: fix fs isoc's transfer error
Due to the scheduler allocates the optimal bandwidth for FS ISOC endpoints,
this may be not enough actually and causes data transfer error, so come up
with an estimate that is no less than the worst case bandwidth used for
any one mframe, but may be an over-estimate.
ChiYuan Huang [Tue, 10 May 2022 05:13:00 +0000 (13:13 +0800)]
usb: typec: tcpci_mt6360: Update for BMC PHY setting
Update MT6360 BMC PHY Tx/Rx setting for the compatibility.
Macpaul reported this CtoDP cable attention message cannot be received from
MT6360 TCPC. But actually, attention message really sent from UFP_D
device.
After RD's comment, there may be BMC PHY Tx/Rx setting causes this issue.
Mathias Nyman [Wed, 11 May 2022 22:04:49 +0000 (01:04 +0300)]
xhci: Remove quirk for over 10 year old evaluation hardware
The XHCI_RESET_EP_QUIRK was added in 2009 to support prototype xHC
hardware from Fresco Logic that needed an additional configure endpoint
command after a reset endpoint.
That hardware should not have made it to the market.
Now, 13 years later its about time we get rid of it.
quirk was added in commit ac9d8fe7c6a8 ("USB: xhci: Add quirk for Fresco
Logic xHCI hardware.")
Print a debug message about the removed quirk if against all odds we run
into this controller.
Mathias Nyman [Wed, 11 May 2022 22:04:47 +0000 (01:04 +0300)]
xhci: use generic command timer for stop endpoint commands.
The 'stop endpoint' command timer was started when a 'stop endpoint'
command was added to the command queue.
This can trigger unwanted timeouts if there are several pending commands
in the queue that xHC needs to handle first.
The generic command timer, which was added later than the 'stop endpoint'
timeout timer, times each command currently being handled by xHC hardware.
A timed out stop endpoint command was treated as a more severe issue than
other failed commands, so the separate stop endpoint timer was left
unchanged.
Use the generic command timer for stop endpoint commands. Identify if
the timed out command was a stop endpoint command in the generic handler,
and treat it with the same severity as earlier.
projects / people / ms / linux.git / log
