Giulio Benetti [Tue, 11 Jan 2022 21:54:14 +0000 (16:54 -0500)]
ARM: dts: imx: Add i.MXRT1050-EVK support
The NXP i.MXRT1050 Evaluation Kit (EVK) provides a platform for rapid
evaluation of the i.MXRT, which features NXP's implementation of the Arm
Cortex-M7 core.
The EVK provides 32 MB SDRAM, 64 MB Quad SPI flash, Micro SD card socket,
USB 2.0 OTG.
This patch aims to support the preliminary booting up features
as follows:
GPIO
LPUART
SD/MMC
irqchip/armada-370-xp: Do not touch Performance Counter Overflow on A375, A38x, A39x
Register ARMADA_370_XP_INT_FABRIC_MASK_OFFS is Armada 370 and XP specific
and on new Armada platforms it has different meaning. It does not configure
Performance Counter Overflow interrupt masking. So do not touch this
register on non-A370/XP platforms (A375, A38x and A39x).
Signed-off-by: Pali Rohár <pali@kernel.org> Cc: stable@vger.kernel.org Fixes: 28da06dfd9e4 ("irqchip: armada-370-xp: Enable the PMU interrupts") Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Marc Zyngier <maz@kernel.org> Link: https://lore.kernel.org/r/20220425113706.29310-1-pali@kernel.org
David S. Miller [Fri, 6 May 2022 11:07:56 +0000 (12:07 +0100)]
Merge branch 'tso-gso-limit-split'
Jakub Kicinski says:
====================
net: disambiguate the TSO and GSO limits
This series separates the device-reported TSO limitations
from the user space-controlled GSO limits. It used to be that
we only had the former (HW limits) but they were named GSO.
This probably lead to confusion and letting user override them.
The problem came up in the BIG TCP discussion between Eric and
Alex, and seems like something we should address.
Targeting net-next because (a) nobody is reporting problems;
and (b) there is a tiny but non-zero chance that some actually
wants to lift the HW limitations.
====================
Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Fri, 6 May 2022 02:51:32 +0000 (19:51 -0700)]
net: don't allow user space to lift the device limits
Up until commit 46e6b992c250 ("rtnetlink: allow GSO maximums to
be set on device creation") the gso_max_segs and gso_max_size
of a device were not controlled from user space.
The quoted commit added the ability to control them because of
the following setup:
netns A | netns B
veth<->veth eth0
If eth0 has TSO limitations and user wants to efficiently forward
traffic between eth0 and the veths they should copy the TSO
limitations of eth0 onto the veths. This would happen automatically
for macvlans or ipvlan but veth users are not so lucky (given the
loose coupling).
Unfortunately the commit in question allowed users to also override
the limits on real HW devices.
It may be useful to control the max GSO size and someone may be using
that ability (not that I know of any user), so create a separate set
of knobs to reliably record the TSO limitations. Validate the user
requests.
Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Fri, 6 May 2022 02:51:31 +0000 (19:51 -0700)]
net: add netif_inherit_tso_max()
To make later patches smaller create a helper for inheriting
the TSO limitations of a lower device. The TSO in the name
is not an accident, subsequent patches will replace GSO
with TSO in more names.
Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Maximilian Luz [Fri, 29 Apr 2022 19:57:38 +0000 (21:57 +0200)]
platform/surface: aggregator: Fix initialization order when compiling as builtin module
When building the Surface Aggregator Module (SAM) core, registry, and
other SAM client drivers as builtin modules (=y), proper initialization
order is not guaranteed. Due to this, client driver registration
(triggered by device registration in the registry) races against bus
initialization in the core.
If any attempt is made at registering the device driver before the bus
has been initialized (i.e. if bus initialization fails this race) driver
registration will fail with a message similar to:
Driver surface_battery was unable to register with bus_type surface_aggregator because the bus was not initialized
Switch from module_init() to subsys_initcall() to resolve this issue.
Note that the serdev subsystem uses postcore_initcall() so we are still
able to safely register the serdev device driver for the core.
Fixes: c167b9c7e3d6 ("platform/surface: Add Surface Aggregator subsystem") Reported-by: Blaž Hrastnik <blaz@mxxn.io> Signed-off-by: Maximilian Luz <luzmaximilian@gmail.com> Link: https://lore.kernel.org/r/20220429195738.535751-1-luzmaximilian@gmail.com Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Maximilian Luz [Fri, 29 Apr 2022 18:00:49 +0000 (20:00 +0200)]
platform/surface: gpe: Add support for Surface Pro 8
The new Surface Pro 8 uses GPEs for lid events as well. Add an entry for
that so that the lid can be used to wake the device. Note that this is a
device with a keyboard type-cover, where this acts as the "lid".
The probe function, pmt_telem_probe(), adds an entry for devices even if
they have not been initialized. This results in the array of initialized
devices containing both initialized and uninitialized entries. This
causes a panic in the remove function, pmt_telem_remove() which expects
the array to only contain initialized entries.
Only use an entry when a device is initialized.
Cc: "David E. Box" <david.e.box@linux.intel.com> Cc: Hans de Goede <hdegoede@redhat.com> Cc: Mark Gross <markgross@kernel.org> Cc: platform-driver-x86@vger.kernel.org Signed-off-by: David Arcari <darcari@redhat.com> Signed-off-by: Prarit Bhargava <prarit@redhat.com> Reviewed-by: David E. Box <david.e.box@linux.intel.com> Link: https://lore.kernel.org/r/20220429122322.2550003-1-prarit@redhat.com Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
platform/x86: thinkpad_acpi: Add a s2idle resume quirk for a number of laptops
Lenovo laptops that contain NVME SSDs across a variety of generations have
trouble resuming from suspend to idle when the IOMMU translation layer is
active for the NVME storage device.
This generally manifests as a large resume delay or page faults. These
delays and page faults occur as a result of a Lenovo BIOS specific SMI
that runs during the D3->D0 transition on NVME devices.
This SMI occurs because of a flag that is set during resume by Lenovo
firmware:
Create a quirk that will run early in the resume process to prevent this
SMI from running. As any of these machines are fixed, they can be peeled
back from this quirk or narrowed down to individual firmware versions.
Paul Gortmaker [Thu, 28 Apr 2022 06:24:29 +0000 (02:24 -0400)]
platform/x86: pmc_atom: dont export pmc_atom_read - no modular users
There is only one user of pmc_atom_read in tree, and that is in
drivers/acpi/acpi_lpss.c -- which can't be anything but built-in.
As such there is no point in adding this function to the global symbol
list exported to modules.
Note that there is no <linux/export.h> include removal since the code
was getting that header implicitly.
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Cc: Aubrey Li <aubrey.li@linux.intel.com> Cc: Hans de Goede <hdegoede@redhat.com> Cc: Mark Gross <markgross@kernel.org> Cc: platform-driver-x86@vger.kernel.org Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Link: https://lore.kernel.org/r/20220428062430.31010-4-paul.gortmaker@windriver.com Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
This function isn't used anywhere in the driver or anywhere in tree.
So remove it. It can always be re-added if/when a use arises.
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Cc: Aubrey Li <aubrey.li@linux.intel.com> Cc: Hans de Goede <hdegoede@redhat.com> Cc: Mark Gross <markgross@kernel.org> Cc: platform-driver-x86@vger.kernel.org Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Link: https://lore.kernel.org/r/20220428062430.31010-2-paul.gortmaker@windriver.com Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
If CONFIG_SUSPEND and CONFIG_DEBUG_FS are not set.
compile error:
drivers/platform/x86/amd-pmc.c:323:12: error: ‘get_metrics_table’ defined but not used [-Werror=unused-function]
static int get_metrics_table(struct amd_pmc_dev *pdev, struct smu_metrics *table)
^~~~~~~~~~~~~~~~~
drivers/platform/x86/amd-pmc.c:298:12: error: ‘amd_pmc_idlemask_read’ defined but not used [-Werror=unused-function]
static int amd_pmc_idlemask_read(struct amd_pmc_dev *pdev, struct device *dev,
^~~~~~~~~~~~~~~~~~~~~
drivers/platform/x86/amd-pmc.c:196:12: error: ‘amd_pmc_get_smu_version’ defined but not used [-Werror=unused-function]
static int amd_pmc_get_smu_version(struct amd_pmc_dev *dev)
^~~~~~~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
To fix building warning, wrap all related code with CONFIG_SUSPEND or CONFIG_DEBUG_FS.
Maximilian Luz [Fri, 29 Apr 2022 19:57:38 +0000 (21:57 +0200)]
platform/surface: aggregator: Fix initialization order when compiling as builtin module
When building the Surface Aggregator Module (SAM) core, registry, and
other SAM client drivers as builtin modules (=y), proper initialization
order is not guaranteed. Due to this, client driver registration
(triggered by device registration in the registry) races against bus
initialization in the core.
If any attempt is made at registering the device driver before the bus
has been initialized (i.e. if bus initialization fails this race) driver
registration will fail with a message similar to:
Driver surface_battery was unable to register with bus_type surface_aggregator because the bus was not initialized
Switch from module_init() to subsys_initcall() to resolve this issue.
Note that the serdev subsystem uses postcore_initcall() so we are still
able to safely register the serdev device driver for the core.
Fixes: c167b9c7e3d6 ("platform/surface: Add Surface Aggregator subsystem") Reported-by: Blaž Hrastnik <blaz@mxxn.io> Signed-off-by: Maximilian Luz <luzmaximilian@gmail.com> Link: https://lore.kernel.org/r/20220429195738.535751-1-luzmaximilian@gmail.com Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Maximilian Luz [Fri, 29 Apr 2022 18:00:49 +0000 (20:00 +0200)]
platform/surface: gpe: Add support for Surface Pro 8
The new Surface Pro 8 uses GPEs for lid events as well. Add an entry for
that so that the lid can be used to wake the device. Note that this is a
device with a keyboard type-cover, where this acts as the "lid".
The probe function, pmt_telem_probe(), adds an entry for devices even if
they have not been initialized. This results in the array of initialized
devices containing both initialized and uninitialized entries. This
causes a panic in the remove function, pmt_telem_remove() which expects
the array to only contain initialized entries.
Only use an entry when a device is initialized.
Cc: "David E. Box" <david.e.box@linux.intel.com> Cc: Hans de Goede <hdegoede@redhat.com> Cc: Mark Gross <markgross@kernel.org> Cc: platform-driver-x86@vger.kernel.org Signed-off-by: David Arcari <darcari@redhat.com> Signed-off-by: Prarit Bhargava <prarit@redhat.com> Reviewed-by: David E. Box <david.e.box@linux.intel.com> Link: https://lore.kernel.org/r/20220429122322.2550003-1-prarit@redhat.com Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
platform/x86: thinkpad_acpi: Add a s2idle resume quirk for a number of laptops
Lenovo laptops that contain NVME SSDs across a variety of generations have
trouble resuming from suspend to idle when the IOMMU translation layer is
active for the NVME storage device.
This generally manifests as a large resume delay or page faults. These
delays and page faults occur as a result of a Lenovo BIOS specific SMI
that runs during the D3->D0 transition on NVME devices.
This SMI occurs because of a flag that is set during resume by Lenovo
firmware:
Create a quirk that will run early in the resume process to prevent this
SMI from running. As any of these machines are fixed, they can be peeled
back from this quirk or narrowed down to individual firmware versions.
This patch series reworks the way in which flow rules that outputs to
OVS internal ports gets handled by the nfp driver.
Previously this made use of a small pre_tun_table, but this only used
destination MAC addresses, and made the implicit assumption that there is
only a single source MAC":"destination MAC" mapping per tunnel. In
hindsight this seems to be a pretty obvious oversight, but this was hidden
in plain sight for quite some time.
This series changes the implementation to make use of the same Neighbour
table for decap that is in use for the tunnel encap solution. It stores
any new Neighbour updates in this table. Previously this path was only
triggered for encapsulation candidates, and the entries were send and
forget, not saved on the host as it is after this series. It also keeps
track of any flow rule that outputs to OVS internal ports (and some
other criteria not worth mentioning here), very similar to how it was
done previously, except now these flows are kept track of in a list.
When a new Neighbour entry gets added this list gets iterated for
potential matches, in which case the table gets updated with a reference
to the flow, and the Neighbour entry on the card gets updated with the
relevant host_ctx. The same happens when a new qualifying flow gets
added - the Neighbour table gets iterated for applicable matches, and
once again the firmware gets updated with the host_ctx when any matches
are found.
Since this also requires a firmware change we add a new capability bit,
and keep the old behaviour in case of older firmware without this bit
set.
This series starts by doing some preparation, then adding the new list
and table entries. Next the functionality to link/unlink these entries
are added, and finally this new functionality is enabled by adding the
DECAP_V2 bit to the driver feature list.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Louis Peens [Thu, 5 May 2022 05:43:48 +0000 (14:43 +0900)]
nfp: flower: enable decap_v2 bit
Finally enable the decap_v2 feature bit now that all the
other bits are in place to configure it correctly.
Signed-off-by: Louis Peens <louis.peens@corigine.com> Signed-off-by: Yinjun Zhang <yinjun.zhang@corigine.com> Signed-off-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Louis Peens [Thu, 5 May 2022 05:43:47 +0000 (14:43 +0900)]
nfp: flower: remove unused neighbour cache
With the neighbour entries now stored in a dedicated table there
is no use to make use of the tunnel route cache anymore, so remove
this.
Signed-off-by: Louis Peens <louis.peens@corigine.com> Signed-off-by: Yinjun Zhang <yinjun.zhang@corigine.com> Signed-off-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Louis Peens [Thu, 5 May 2022 05:43:46 +0000 (14:43 +0900)]
nfp: flower: link pre_tun flow rules with neigh entries
Add helper functions that can create links between flow rules
and cached neighbour entries. Also add the relevant calls to
these functions.
* When a new neighbour entry gets added cycle through the saved
pre_tun flow list and link any relevant matches. Update the
neighbour table on the nfp with this new information.
* When a new pre_tun flow rule gets added iterate through the
save neighbour entries and link any relevant matches. Once
again update the nfp neighbour table with any new links.
* Do the inverse when deleting - remove any created links and
also inform the nfp of this.
Signed-off-by: Louis Peens <louis.peens@corigine.com> Signed-off-by: Yinjun Zhang <yinjun.zhang@corigine.com> Signed-off-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates the way in which the tunnel neighbour entries
are handled. Previously they were mostly send-and-forget, with
just the destination IP's cached in a list. This update changes
to a scheme where the neighbour entry information is stored in
a hash table.
The reason for this is that the neighbour table will now also
be used on the decapsulation path, whereas previously it was
only used for encapsulation. We need to save more of the neighbour
information in order to link them with flower flows in follow
up patches.
Updating of the neighbour table is now also handled by the same
function, instead of separate *_write_neigh_vX functions.
Signed-off-by: Louis Peens <louis.peens@corigine.com> Signed-off-by: Yinjun Zhang <yinjun.zhang@corigine.com> Signed-off-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Louis Peens [Thu, 5 May 2022 05:43:44 +0000 (14:43 +0900)]
nfp: flower: update nfp_tun_neigh structs
Prepare for more rework in following patches by updating
the existing nfp_neigh_structs. The update allows for
the same headers to be used for both old and new firmware,
with a slight length adjustment when sending the control message
to the firmware.
Signed-off-by: Louis Peens <louis.peens@corigine.com> Signed-off-by: Yinjun Zhang <yinjun.zhang@corigine.com> Signed-off-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Louis Peens [Thu, 5 May 2022 05:43:43 +0000 (14:43 +0900)]
nfp: flower: fixup ipv6/ipv4 route lookup for neigh events
When a callback is received to invalidate a neighbour entry
there is no need to try and populate any other flow information.
Only the flowX->daddr information is needed as lookup key to delete
an entry from the NFP neighbour table. Fix this by only doing the
lookup if the callback is for a new entry.
As part of this cleanup remove the setting of flow6.flowi6_proto, as
this is not needed either, it looks to be a possible leftover from a
previous implementation.
Signed-off-by: Louis Peens <louis.peens@corigine.com> Signed-off-by: Yinjun Zhang <yinjun.zhang@corigine.com> Signed-off-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Louis Peens [Thu, 5 May 2022 05:43:42 +0000 (14:43 +0900)]
nfp: flower: enforce more strict pre_tun checks
Make sure that the rule also matches on source MAC address. On top
of that also now save the src and dst MAC addresses similar to how
vlan_tci is saved - this will be used in later comparisons with
neighbour entries. Indicate if the flow matched on ipv4 or ipv6.
Populate the vlan_tpid field that got added to the pre_run_rule
struct as well.
Signed-off-by: Louis Peens <louis.peens@corigine.com> Signed-off-by: Yinjun Zhang <yinjun.zhang@corigine.com> Signed-off-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Louis Peens [Thu, 5 May 2022 05:43:41 +0000 (14:43 +0900)]
nfp: flower: add/remove predt_list entries
Add calls to add and remove flows to the predt_table. This very simply
just allocates and add a new pretun entry if detected as such, and
removes it when encountered on a delete flow.
Compatibility for older firmware is kept in place through the
DECAP_V2 feature bit.
Signed-off-by: Louis Peens <louis.peens@corigine.com> Signed-off-by: Yinjun Zhang <yinjun.zhang@corigine.com> Signed-off-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Louis Peens [Thu, 5 May 2022 05:43:40 +0000 (14:43 +0900)]
nfp: flower: add infrastructure for pre_tun rework
The previous implementation of using a pre_tun_table for decap has
some limitations, causing flows to end up unoffloaded when in fact
we are able to offload them. This is because the pre_tun_table does
not have enough matching resolution. The next step is to instead make
use of the neighbour table which already exists for the encap direction.
This patch prepares for this by:
- Moving nfp_tun_neigh/_v6 to main.h.
- Creating two new "wrapping" structures, one to keep track of neighbour
entries (previously they were send-and-forget), and another to keep
track of pre_tun flows.
- Create a new list in nfp_flower_priv to keep track of pre_tunnel flows
- Create a new table in nfp_flower_priv to keep track of next neighbour
entries
- Initialising and destroying these new list/tables
- Extending nfp_fl_payload->pre_tun_rule to save more information for
future use.
Signed-off-by: Louis Peens <louis.peens@corigine.com> Signed-off-by: Yinjun Zhang <yinjun.zhang@corigine.com> Signed-off-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Flushing system-wide workqueues is dangerous and will be forbidden.
Replace system_wq with local atmel_wq.
If CONFIG_CRYPTO_DEV_ATMEL_{I2C,ECC,SHA204A}=y, the ordering in Makefile
guarantees that module_init() for atmel-i2c runs before module_init()
for atmel-ecc and atmel-sha204a runs.
Returning an error value in an i2c remove callback results in an error
message being emitted by the i2c core, but otherwise it doesn't make a
difference. The device goes away anyhow and the devm cleanups are
called.
As atmel_sha204a_remove already emits an error message ant the additional
error message by the i2c core doesn't add any useful information, change
the return value to zero to suppress this error message.
Note that after atmel_sha204a_remove() returns *i2c_priv is freed, so there
is trouble ahead because atmel_sha204a_rng_done() might be called after
that freeing. So make the error message a bit more frightening.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
crypto: atmel-sha204a - Add support for ATSHA204 cryptochip
ATSHA204 is predecessor of ATSHA204A which supports less features and some
of them are slightly different.
Introduce a new compatible string for ATSHA204 cryptochip "atmel,atsha204".
Current version of Linux kernel driver atmel-sha204a.c implements only hw
random number generator which is same in both ATSHA204 and ATSHA204A
cryptochips. So driver already supports also ATSHA204 hw generator, so just
simply extends list of compatible strings.
Signed-off-by: Pali Rohár <pali@kernel.org> Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Randy Dunlap [Sat, 30 Apr 2022 05:01:23 +0000 (22:01 -0700)]
KVM: arm64: nvhe: Eliminate kernel-doc warnings
Don't use begin-kernel-doc notation (/**) for comments that are not in
kernel-doc format.
This prevents these kernel-doc warnings:
arch/arm64/kvm/hyp/nvhe/switch.c:126: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
* Disable host events, enable guest events
arch/arm64/kvm/hyp/nvhe/switch.c:146: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
* Disable guest events, enable host events
arch/arm64/kvm/hyp/nvhe/switch.c:164: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
* Handler for protected VM restricted exceptions.
arch/arm64/kvm/hyp/nvhe/switch.c:176: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
* Handler for protected VM MSR, MRS or System instruction execution in AArch64.
arch/arm64/kvm/hyp/nvhe/switch.c:196: warning: Function parameter or member 'vcpu' not described in 'kvm_handle_pvm_fpsimd'
arch/arm64/kvm/hyp/nvhe/switch.c:196: warning: Function parameter or member 'exit_code' not described in 'kvm_handle_pvm_fpsimd'
arch/arm64/kvm/hyp/nvhe/switch.c:196: warning: expecting prototype for Handler for protected floating(). Prototype was for kvm_handle_pvm_fpsimd() instead
Fixes: 09cf57eba304 ("KVM: arm64: Split hyp/switch.c to VHE/nVHE") Fixes: 1423afcb4117 ("KVM: arm64: Trap access to pVM restricted features") Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Reported-by: kernel test robot <lkp@intel.com> Cc: Fuad Tabba <tabba@google.com> Cc: Marc Zyngier <maz@kernel.org> Cc: David Brazdil <dbrazdil@google.com> Cc: James Morse <james.morse@arm.com> Cc: Alexandru Elisei <alexandru.elisei@arm.com> Cc: Suzuki K Poulose <suzuki.poulose@arm.com> Cc: linux-arm-kernel@lists.infradead.org Cc: kvmarm@lists.cs.columbia.edu Signed-off-by: Marc Zyngier <maz@kernel.org> Link: https://lore.kernel.org/r/20220430050123.2844-1-rdunlap@infradead.org
KVM: arm64: Avoid unnecessary absolute addressing via literals
There are a few cases in the nVHE code where we take the absolute
address of a symbol via a literal pool entry, and subsequently translate
it to another address space (PA, kimg VA, kernel linear VA, etc).
Originally, this literal was needed because we relied on a different
translation for absolute references, but this is no longer the case, so
we can simply use relative addressing instead. This removes a couple of
RELA entries pointing into the .text segment.
David S. Miller [Fri, 6 May 2022 09:50:05 +0000 (10:50 +0100)]
Merge branch '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue
Tony Nguyen says:
====================
100GbE Intel Wired LAN Driver Updates 2022-05-05
This series contains updates to ice driver only.
Wan Jiabing converts an open coded min selection to min_t().
Maciej commonizes on a single find VSI function and removes the
duplicated implementation.
Wojciech adjusts the return value when exceeding ICE_MAX_CHAIN_WORDS to,
a more appropriate, -ENOSPC and allows for the error to be propagated.
Michal adds support for ndo_get_devlink_port().
Jake does some cleanup related to virtualization code. Mainly involving
function header comments and wording changes. NULL checks are added to
ice_get_vf_vsi() calls in order to prevent static analysis tools from
complaining that a NULL value could be dereferenced.
---
v2: Dropped patch 1: "ice: Add support for classid based queue selection"
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Phil Edworthy [Wed, 4 May 2022 09:44:56 +0000 (10:44 +0100)]
arm64: dts: renesas: Add initial DTSI for RZ/V2M SoC
Details of the SoC can be found here:
https://www.renesas.com/us/en/products/microcontrollers-microprocessors/rz-cortex-a-mpus/rzv2m-dual-cortex-a53-lpddr4x32bit-ai-accelerator-isp-4k-video-codec-4k-camera-input-fhd-display-output
arm64: dts: renesas: r8a779a0: Update to R-Car Gen4 compatible values
Despite the name, R-Car V3U is the first member of the R-Car Gen4
family. Hence update the compatible properties in various device nodes
to include family-specific compatible values for R-Car Gen4 instead of
R-Car Gen3:
- DMAC,
- (H)SCIF,
- I2C,
- IPMMU,
- WDT.
arm64: dts: renesas: Add interrupt-names to CANFD nodes
The Renesas R-Car CAN-FD Controller on R-Car Gen3 and RZ/G2 SoCs has two
interrupts. Add interrupt-names properties to all CAN-FD device nodes
to identify the individual interrupts, so we can make this property a
required property in the DT bindings.
Biju Das [Sun, 1 May 2022 11:29:25 +0000 (12:29 +0100)]
arm64: dts: renesas: r9a07g043: Create thermal zone to support IPA
Setup a thermal zone driven by SoC temperature sensor.
Create passive trip points and bind them to CPUFreq cooling
device that supports power extension.
Based on the work done by Dien Pham <dien.pham.ry@renesas.com>
and others for r8a77990 SoC.
Add suffix '-clk' for can and extal clk node names and replace the
clk node names audio_clk{1,2} with audio{1,2}-clk as per the device
tree specification.
Add suffix '-clk' for can and extal clk node names and replace the
clk node names audio_clk{1,2} with audio{1,2}-clk as per the device
tree specification.
UART 0 to 2 do not have DMA support, while UART 3 to 7 do.
Fill the "dmas" and "dma-names" properties for each of these nodes.
Please mind that these nodes go through the dmamux node which will
redirect the requests to the right DMA controller. The first 4 cells of
the "dmas" properties will be transferred as-is to the DMA
controllers. The last 2 cells are consumed by the dmamux. Which means
cell 0 and 4 are almost redundant, one giving the controller request ID
and the other the dmamux channel which is a 1:1 translation of the
request IDs, shifted by 16 when pointing to the second DMA controller.
Endpoints node must have a remote-endpoint property, as endpoints only
exist to model a link between ports. Drop the empty rgb output endpoints
from SoC dtsi files, and declare them in the board dts instead.
Endpoints node must have a remote-endpoint property, as endpoints only
exist to model a link between ports. Drop the empty lvds endpoints from
SoC dtsi files, they should be instead declared in the board dts or in
overlays.
Biju Das [Fri, 29 Apr 2022 07:24:00 +0000 (08:24 +0100)]
arm64: dts: renesas: rzg2ul-smarc: Enable USB2.0 support
Enable USB2.0 Host/Device support on RZ/G2UL SMARC EVK by
adding usb{0,1} pincontrol entries to the soc-pinctrl dtsi
and deleting the nodes which disabled it.
Biju Das [Fri, 29 Apr 2022 07:23:58 +0000 (08:23 +0100)]
arm64: dts: renesas: rzg2l-smarc: Move ssi0 and cpu sound_dai nodes from common dtsi
On RZ/G2{L,LC} SoM module, the wm8978 audio codec is connected to ssi0,
whereas on RZ/G2UL it is connected to ssi1. So move ssi0 and cpu
sound_dai nodes from common dtsi to board specific dtsi.
Marco Elver [Tue, 3 May 2022 07:38:44 +0000 (09:38 +0200)]
printk, tracing: fix console tracepoint
The original intent of the 'console' tracepoint per the commit 95100358491a
("printk/tracing: Add console output tracing") had been to "[...] record
any printk messages into the trace, regardless of the current console
loglevel. This can help correlate (existing) printk debugging with other
tracing."
Petr points out [1] that calling trace_console_rcuidle() in
call_console_driver() had been the wrong thing for a while, because
"printk() always used console_trylock() and the message was flushed to
the console only when the trylock succeeded. And it was always deferred
in NMI or when printed via printk_deferred()."
With the commit 09c5ba0aa2fc ("printk: add kthread console printers"),
things only got worse, and calls to call_console_driver() no longer
happen with typical printk() calls but always appear deferred [2].
As such, the tracepoint can no longer serve its purpose to clearly
correlate printk() calls and other tracing, as well as breaks usecases
that expect every printk() call to result in a callback of the console
tracepoint. Notably, the KFENCE and KCSAN test suites, which want to
capture console output and assume a printk() immediately gives us a
callback to the console tracepoint.
Fix the console tracepoint by moving it into printk_sprint() [3].
One notable difference is that by moving tracing into printk_sprint(),
the 'text' will no longer include the "header" (loglevel and timestamp),
but only the raw message. Arguably this is less of a problem now that
the console tracepoint happens on the printk() call and isn't delayed.
Dongliang Mu [Fri, 6 May 2022 07:24:25 +0000 (15:24 +0800)]
HID: bigben: fix slab-out-of-bounds Write in bigben_probe
There is a slab-out-of-bounds Write bug in hid-bigbenff driver.
The problem is the driver assumes the device must have an input but
some malicious devices violate this assumption.
Fix this by checking hid_device's input is non-empty before its usage.
Mark Brown [Thu, 5 May 2022 17:10:43 +0000 (18:10 +0100)]
ARM: configs: at91: Enable options required for systemd
Even smaller embedded systems are using systemd these days, as
are test automation systems like KernelCI, so it is useful to be
able to use systemd on these boards by default. Enable options
that are missing in the at91_dt_defconfig, cgroups which is
critical and autofs4 which is less critical but causes warnings
on boot when not available.
firmware_loader: use kernel credentials when reading firmware
Device drivers may decide to not load firmware when probed to avoid
slowing down the boot process should the firmware filesystem not be
available yet. In this case, the firmware loading request may be done
when a device file associated with the driver is first accessed. The
credentials of the userspace process accessing the device file may be
used to validate access to the firmware files requested by the driver.
Ensure that the kernel assumes the responsibility of reading the
firmware.
This was observed on Android for a graphic driver loading their firmware
when the device file (e.g. /dev/mali0) was first opened by userspace
(i.e. surfaceflinger). The security context of surfaceflinger was used
to validate the access to the firmware file (e.g.
/vendor/firmware/mali.bin).
Previously, Android configurations were not setting up the
firmware_class.path command line argument and were relying on the
userspace fallback mechanism. In this case, the security context of the
userspace daemon (i.e. ueventd) was consistently used to read firmware
files. More Android devices are now found to set firmware_class.path
which gives the kernel the opportunity to read the firmware directly
(via kernel_read_file_from_path_initns). In this scenario, the current
process credentials were used, even if unrelated to the loading of the
firmware file.
Signed-off-by: Thiébaud Weksteen <tweek@google.com> Cc: <stable@vger.kernel.org> # 5.10 Reviewed-by: Paul Moore <paul@paul-moore.com> Acked-by: Luis Chamberlain <mcgrof@kernel.org> Link: https://lore.kernel.org/r/20220502004952.3970800-1-tweek@google.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dan Carpenter [Thu, 5 May 2022 10:32:59 +0000 (13:32 +0300)]
driver core: location: Check for allocations failure
Check whether the kzalloc() succeeds and return false if it fails.
Fixes: 6423d2951087 ("driver core: Add sysfs support for physical location of a device") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Link: https://lore.kernel.org/r/YnOn28OFBHHd5bQb@kili Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Lukasz Luba [Wed, 27 Apr 2022 08:08:06 +0000 (09:08 +0100)]
arch_topology: Trace the update thermal pressure
Add trace event to capture the moment of the call for updating the thermal
pressure value. It's helpful to investigate how often those events occur
in a system dealing with throttling. This trace event is needed since the
old 'cdev_update' might not be used by some drivers.
The old 'cdev_update' trace event only provides a cooling state
value: [0, n]. That state value then needs additional tools to translate
it: state -> freq -> capacity -> thermal pressure. This new trace event
just stores proper thermal pressure value in the trace buffer, no need
for additional logic. This is helpful for cooperation when someone can
simply sends to the list the trace buffer output from the platform (no
need from additional information from other subsystems).
There are also platforms which due to some design reasons don't use
cooling devices and thus don't trigger old 'cdev_update' trace event.
They are also important and measuring latency for the thermal signal
raising/decaying characteristics is in scope. This new trace event
would cover them as well.
We already have a trace point 'pelt_thermal_tp' which after a change to
trace event can be paired with this new 'thermal_pressure_update' and
derive more insight what is going on in the system under thermal pressure
(and why).
Imran Khan [Wed, 4 May 2022 09:51:19 +0000 (19:51 +1000)]
kernfs: Rename kernfs_put_open_node to kernfs_unlink_open_file.
Since we are no longer using refcnt for kernfs_open_node instances, rename
kernfs_put_open_node to kernfs_unlink_open_file to reflect this change.
Also update function description and inline comments accordingly.
Liu Ying [Tue, 19 Apr 2022 01:08:48 +0000 (09:08 +0800)]
drm/bridge: nwl-dsi: Set PHY mode in nwl_dsi_mode_set()
The Northwest Logic MIPI DSI host controller embedded in i.MX8qxp
works with a Mixel MIPI DPHY + LVDS PHY combo to support either
a MIPI DSI display or a LVDS display. So, this patch calls
phy_set_mode() from nwl_dsi_mode_set() to set PHY mode to MIPI DPHY
explicitly.
Cc: Guido Günther <agx@sigxcpu.org> Cc: Robert Chiras <robert.chiras@nxp.com> Cc: Martin Kepplinger <martin.kepplinger@puri.sm> Cc: Andrzej Hajda <andrzej.hajda@intel.com> Cc: Neil Armstrong <narmstrong@baylibre.com> Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com> Cc: Jonas Karlman <jonas@kwiboo.se> Cc: Jernej Skrabec <jernej.skrabec@gmail.com> Cc: David Airlie <airlied@linux.ie> Cc: Daniel Vetter <daniel@ffwll.ch> Cc: NXP Linux Team <linux-imx@nxp.com> Signed-off-by: Liu Ying <victor.liu@nxp.com> Acked-by: Robert Foss <robert.foss@linaro.org> Reviewed-by: Guido Günther <agx@sigxcpu.org> Signed-off-by: Guido Günther <agx@sigxcpu.org> Link: https://patchwork.freedesktop.org/patch/msgid/20220419010852.452169-2-victor.liu@nxp.com
Tvrtko Ursulin [Thu, 5 May 2022 11:00:07 +0000 (12:00 +0100)]
drm/i915: Don't use DRM_DEBUG_WARN_ON for ring unexpectedly not idle
DRM_DEBUG_WARN_ON should only be used when we are certain CI is guaranteed
to exercise a certain code path, so in case of values coming from MMIO
reads we cannot be sure CI will have all the possible SKUs and parts, or
that it will catch all possible error conditions. Use drm_warn instead.
Tvrtko Ursulin [Thu, 5 May 2022 11:00:06 +0000 (12:00 +0100)]
drm/i915: Don't use DRM_DEBUG_WARN_ON for unexpected l3bank/mslice config
DRM_DEBUG_WARN_ON should only be used when we are certain CI is guaranteed
to exercise a certain code path, so in case of values coming from MMIO
reads we cannot be sure CI will have all the possible SKUs and parts.
Use drm_warn instead and move logging to init phase while at it.
export: fix string handling of namespace in EXPORT_SYMBOL_NS
Commit c3a6cf19e695 ("export: avoid code duplication in
include/linux/export.h") broke the ability for a defined string to be
used as a namespace value. Fix this up by using stringify to properly
encode the namespace name.
rpmsg: Fix calling device_lock() on non-initialized device
driver_set_override() helper uses device_lock() so it should not be
called before rpmsg_register_device() (which calls device_register()).
Effect can be seen with CONFIG_DEBUG_MUTEXES:
Refactor the rpmsg_register_device() function to use two-step device
registering (initialization + add) and call driver_set_override() in
proper moment.
This moves the code around, so while at it also NULL-ify the
rpdev->driver_override in error path to be sure it won't be kfree()
second time.
Fixes: 42cd402b8fd4 ("rpmsg: Fix kfree() of static memory on setting driver_override") Reported-by: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Tested-by: Marek Szyprowski <m.szyprowski@samsung.com> Link: https://lore.kernel.org/r/20220429195946.1061725-2-krzysztof.kozlowski@linaro.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ard Biesheuvel [Tue, 3 May 2022 12:29:39 +0000 (14:29 +0200)]
efi: stub: prefer mirrored memory for randomized allocations
If the system exposes memory regions with the EFI_MORE_RELIABLE
attribute, it is implied that it is intended to be used for allocations
that are relatively important, such as the kernel's static image.
Since efi_random_alloc() is mostly (only) used for allocating space for
the kernel image, let's update it to take this into account, and
disregard all memory without the EFI_MORE_RELIABLE attribute if there is
sufficient memory available that does have this attribute.
Note that this change only affects booting with randomization enabled.
In other cases, the EFI stub runs the kernel image in place unless its
placement is unsuitable for some reason (i.e., misaligned, or its BSS
overlaps with another allocation), and it is left to the bootloader to
ensure that the kernel was loaded into EFI_MORE_RELIABLE memory if this
is desired.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org> Reviewed-by: Kefeng Wang <wangkefeng.wang@huawei.com>
projects / people / ms / linux.git / log
