Since a pointer to struct snd_dmaengine_pcm_config is passed,
snd_dmaengine_pcm_prepare_slave_config() is no longer called unless it's
explicitly set in prepare_slave_config.
Mark Brown [Wed, 20 Apr 2022 19:34:54 +0000 (20:34 +0100)]
ASoC: max98090: Generate notifications on changes for custom control
The max98090 driver has some custom controls which share a put() function
which returns 0 unconditionally, meaning that events are not generated
when the value changes. Fix that.
Mark Brown [Wed, 20 Apr 2022 19:34:53 +0000 (20:34 +0100)]
ASoC: max98090: Reject invalid values in custom control put()
The max98090 driver has a custom put function for some controls which can
only be updated in certain circumstances which makes no effort to validate
that input is suitable for the control, allowing out of spec values to be
written to the hardware and presented to userspace. Fix this by returning
an error when invalid values are written.
Nicholas Piggin [Fri, 22 Apr 2022 14:14:46 +0000 (00:14 +1000)]
timers/nohz: Switch to ONESHOT_STOPPED in the low-res handler when the tick is stopped
When tick_nohz_stop_tick() stops the tick and high resolution timers are
disabled, then the clock event device is not put into ONESHOT_STOPPED
mode. This can lead to spurious timer interrupts with some clock event
device drivers that don't shut down entirely after firing.
Eliminate these by putting the device into ONESHOT_STOPPED mode at points
where it is not being reprogrammed. When there are no timers active, then
tick_program_event() with KTIME_MAX can be used to stop the device. When
there is a timer active, the device can be stopped at the next tick (any
new timer added by timers will reprogram the tick).
Amir Goldstein [Fri, 22 Apr 2022 12:03:25 +0000 (15:03 +0300)]
fanotify: implement "evictable" inode marks
When an inode mark is created with flag FAN_MARK_EVICTABLE, it will not
pin the marked inode to inode cache, so when inode is evicted from cache
due to memory pressure, the mark will be lost.
When an inode mark with flag FAN_MARK_EVICATBLE is updated without using
this flag, the marked inode is pinned to inode cache.
When an inode mark is updated with flag FAN_MARK_EVICTABLE but an
existing mark already has the inode pinned, the mark update fails with
error EEXIST.
Evictable inode marks can be used to setup inode marks with ignored mask
to suppress events from uninteresting files or directories in a lazy
manner, upon receiving the first event, without having to iterate all
the uninteresting files or directories before hand.
The evictbale inode mark feature allows performing this lazy marks setup
without exhausting the system memory with pinned inodes.
Amir Goldstein [Fri, 22 Apr 2022 12:03:24 +0000 (15:03 +0300)]
fanotify: factor out helper fanotify_mark_update_flags()
Handle FAN_MARK_IGNORED_SURV_MODIFY flag change in a helper that
is called after updating the mark mask.
Replace the added and removed return values and help variables with
bool recalc return values and help variable, which makes the code a
bit easier to follow.
Rename flags argument to fan_flags to emphasize the difference from
mark->flags.
Amir Goldstein [Fri, 22 Apr 2022 12:03:22 +0000 (15:03 +0300)]
fsnotify: allow adding an inode mark without pinning inode
fsnotify_add_mark() and variants implicitly take a reference on inode
when attaching a mark to an inode.
Make that behavior opt-out with the mark flag FSNOTIFY_MARK_FLAG_NO_IREF.
Instead of taking the inode reference when attaching connector to inode
and dropping the inode reference when detaching connector from inode,
take the inode reference on attach of the first mark that wants to hold
an inode reference and drop the inode reference on detach of the last
mark that wants to hold an inode reference.
Backends can "upgrade" an existing mark to take an inode reference, but
cannot "downgrade" a mark with inode reference to release the refernce.
This leaves the choice to the backend whether or not to pin the inode
when adding an inode mark.
This is intended to be used when adding a mark with ignored mask that is
used for optimization in cases where group can afford getting unneeded
events and reinstate the mark with ignored mask when inode is accessed
again after being evicted.
Amir Goldstein [Fri, 22 Apr 2022 12:03:21 +0000 (15:03 +0300)]
dnotify: use fsnotify group lock helpers
Before commit 9542e6a643fc6 ("nfsd: Containerise filecache laundrette")
nfsd would close open files in direct reclaim context. There is no
guarantee that others memory shrinkers don't do the same and no
guarantee that future shrinkers won't do that.
For example, if overlayfs implements inode cache of fscache would
keep open files to cached objects, inode shrinkers could end up closing
open files to underlying fs.
Direct reclaim from dnotify mark allocation context may try to close
open files that have dnotify marks of the same group and hit a deadlock
on mark_mutex.
Set the FSNOTIFY_GROUP_NOFS flag to prevent going into direct reclaim
from allocations under dnotify group lock and use the safe group lock
helpers.
Amir Goldstein [Fri, 22 Apr 2022 12:03:20 +0000 (15:03 +0300)]
nfsd: use fsnotify group lock helpers
Before commit 9542e6a643fc6 ("nfsd: Containerise filecache laundrette")
nfsd would close open files in direct reclaim context and that could
cause a deadlock when fsnotify mark allocation went into direct reclaim
and nfsd shrinker tried to free existing fsnotify marks.
To avoid issues like this in future code, set the FSNOTIFY_GROUP_NOFS
flag on nfsd fsnotify group to prevent going into direct reclaim from
fsnotify_add_inode_mark().
Amir Goldstein [Fri, 22 Apr 2022 12:03:17 +0000 (15:03 +0300)]
fsnotify: create helpers for group mark_mutex lock
Create helpers to take and release the group mark_mutex lock.
Define a flag FSNOTIFY_GROUP_NOFS in fsnotify_group that determines
if the mark_mutex lock is fs reclaim safe or not. If not safe, the
lock helpers take the lock and disable direct fs reclaim.
In that case we annotate the mutex with a different lockdep class to
express to lockdep that an allocation of mark of an fs reclaim safe group
may take the group lock of another "NOFS" group to evict inodes.
For now, converted only the callers in common code and no backend
defines the NOFS flag. It is intended to be set by fanotify for
evictable marks support.
Amir Goldstein [Fri, 22 Apr 2022 12:03:16 +0000 (15:03 +0300)]
fsnotify: make allow_dups a property of the group
Instead of passing the allow_dups argument to fsnotify_add_mark()
as an argument, define the group flag FSNOTIFY_GROUP_DUPS to express
the allow_dups behavior and set this behavior at group creation time
for all calls of fsnotify_add_mark().
Rename the allow_dups argument to generic add_flags argument for future
use.
Amir Goldstein [Fri, 22 Apr 2022 12:03:15 +0000 (15:03 +0300)]
fsnotify: pass flags argument to fsnotify_alloc_group()
Add flags argument to fsnotify_alloc_group(), define and use the flag
FSNOTIFY_GROUP_USER in inotify and fanotify instead of the helper
fsnotify_alloc_user_group() to indicate user allocation.
Although the flag FSNOTIFY_GROUP_USER is currently not used after group
allocation, we store the flags argument in the group struct for future
use of other group flags.
Amir Goldstein [Fri, 22 Apr 2022 12:03:14 +0000 (15:03 +0300)]
fsnotify: fix wrong lockdep annotations
Commit 6960b0d909cd ("fsnotify: change locking order") changed some
of the mark_mutex locks in direct reclaim path to use:
mutex_lock_nested(&group->mark_mutex, SINGLE_DEPTH_NESTING);
This change is explained:
"...It uses nested locking to avoid deadlock in case we do the final
iput() on an inode which still holds marks and thus would take the
mutex again when calling fsnotify_inode_delete() in destroy_inode()."
The problem is that the mutex_lock_nested() is not a nested lock at
all. In fact, it has the opposite effect of preventing lockdep from
warning about a very possible deadlock.
Due to these wrong annotations, a deadlock that was introduced with
nfsd filecache in kernel v5.4 went unnoticed in v5.4.y for over two
years until it was reported recently by Khazhismel Kumykov, only to
find out that the deadlock was already fixed in kernel v5.5.
Srinivasan Raju [Thu, 24 Feb 2022 18:20:07 +0000 (18:20 +0000)]
wireless: add plfxlc driver for pureLiFi X, XL, XC devices
This is a driver for pureLiFi X, XL, XC devices which use light to transmit
data, so they are not compatible with normal Wi-Fi devices. The driver uses
separate NL80211_BAND_LC band to distinguish from Wi-Fi. The driver is based
on 802.11 softMAC Architecture and uses native 802.11 for configuration and
management. Station and Ad-Hoc modes are supported.
The driver is compiled and tested in ARM, x86 architectures and compiled in
powerpc architecture. This driver implementation has been based on the zd1211rw
driver.
- Drop CONFIG_BINFMT_AOUT=m (no longer available since commit 19e8b701e258701b ("a.out: Stop building a.out/osf1 support on alpha
and m68k")),
- Enable modular build of the SM3 digest algorithm (no longer
auto-selected since commit 114004696bf23499 ("crypto: sm2 - make
dependent on sm3 library")),
- Drop CONFIG_CRC64=m (auto-selected since commit a7d4383f17e10f33
("block: add pi for extended integrity")),
- Drop CONFIG_TEST_OVERFLOW=m (replaced by auto-modular
CONFIG_OVERFLOW_KUNIT_TEST in commit 617f55e20743fc50 ("lib:
overflow: Convert to Kunit")),
- Drop CONFIG_TEST_STACKINIT=m (replaced by auto-modular
CONFIG_STACKINIT_KUNIT_TEST in commit 02788ebcf521fe78 ("lib:
stackinit: Convert to KUnit")).
s390: add KCSAN instrumentation to barriers and spinlocks
test_barrier fails on s390 because of the missing KCSAN instrumentation
for several synchronization primitives.
Add it to barriers by defining __mb(), __rmb(), __wmb(), __dma_rmb()
and __dma_wmb(), and letting the common code in asm-generic/barrier.h
do the rest.
Spinlocks require instrumentation only on the unlock path; notify KCSAN
that the CPU cannot move memory accesses outside of the spin lock. In
reality it also cannot move stores inside of it, but this is not
important and can be omitted.
Niklas Schnelle [Fri, 25 Feb 2022 08:45:24 +0000 (09:45 +0100)]
s390/pci: add error record for CC 2 retries
Currently it is not detectable from within Linux when PCI instructions
are retried because of a busy condition. Detecting such conditions and
especially how long they lasted can however be quite useful in problem
determination. This patch enables this by adding an s390dbf error log
when a CC 2 is first encountered as well as after the retried
instruction.
Despite being unlikely it may be possible that these added debug
messages drown out important other messages so allow setting the debug
level in zpci_err_insn*() and set their level to 1 so they can be
filtered out if need be.
Reviewed-by: Matthew Rosato <mjrosato@linux.ibm.com> Reviewed-by: Pierre Morel <pmorel@linux.ibm.com> Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com> Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Niklas Schnelle [Thu, 24 Feb 2022 14:45:33 +0000 (15:45 +0100)]
s390/pci: add PCI access type and length to error records
Currently when a PCI instruction returns a non-zero condition code it
can be very hard to tell from the s390dbf logs what kind of instruction
was executed. In case of PCI memory I/O (MIO) instructions it is even
impossible to tell if we attempted a load, store or block store or how
large the access was because only the address is logged.
Improve this by adding an indicator byte for the instruction type to the
error record and also store the length of the access for MIO
instructions where this can not be deduced from the request.
We use the following indicator values:
- 'l': PCI load
- 's': PCI store
- 'b': PCI store block
- 'L': PCI load (MIO)
- 'S': PCI store (MIO)
- 'B': PCI store block (MIO)
- 'M': MPCIFC
- 'R': RPCIT
Reviewed-by: Matthew Rosato <mjrosato@linux.ibm.com> Reviewed-by: Pierre Morel <pmorel@linux.ibm.com> Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com> Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Availability events are logged in s390dbf in s390dbf/pci_error/hex_ascii
even though they don't indicate an error condition.
They have also become redundant as commit 6526a597a2e85 ("s390/pci: add
simpler s390dbf traces for events") added an s390dbf/pci_msg/sprintf log
entry for availability events which contains all non reserved fields of
struct zpci_ccdf_avail. On the other hand the availability entries in
the error log make it easy to miss actual errors and may even overwrite
error entries if the message buffer wraps.
Thus simply remove the availability events from the error log thereby
establishing the rule that any content in s390dbf/pci_error indicates
some kind of error.
Reviewed-by: Matthew Rosato <mjrosato@linux.ibm.com> Reviewed-by: Pierre Morel <pmorel@linux.ibm.com> Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com> Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Niklas Schnelle [Fri, 18 Mar 2022 15:25:31 +0000 (16:25 +0100)]
s390/pci: make better use of zpci_dbg() levels
While the zpci_dbg() macro offers a level parameter this is currently
largely unused. The only instance with higher importance than 3 is the
UID checking change debug message which is not actually more important
as the UID uniqueness guarantee is already exposed in sysfs so this
should rather be 3 as well.
On the other hand the "add ..." message which shows what devices are
visible at the lowest level is essential during problem determination.
By setting its level to 1, lowering the debug level can act as a filter
to only show the available functions.
On the error side the default level is set to 6 while all existing
messages are printed at level 0. This is inconsistent and means there is
no room for having messages be invisible on the default level so instead
set the default level to 3 like for errors matching the default for
debug messages.
Reviewed-by: Matthew Rosato <mjrosato@linux.ibm.com> Reviewed-by: Pierre Morel <pmorel@linux.ibm.com> Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com> Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
The vfio_ap module tries to register for the vfio_ap bus - but that's
the interface that it provides itself, so this does not make much sense,
thus let's simply drop this statement now.
Sven Schnelle [Wed, 6 Apr 2022 07:17:21 +0000 (09:17 +0200)]
s390/vdso: add vdso randomization
Randomize the address of vdso if randomize_va_space is enabled.
Note that this keeps the vdso address on the same PMD as the stack
to avoid allocating an extra page table just for vdso.
Sven Schnelle [Wed, 6 Apr 2022 06:44:49 +0000 (08:44 +0200)]
s390/vdso: map vdso above stack
In the current code vdso is mapped below the stack. This is
problematic when programs mapped to the top of the address space
are allocating a lot of memory, because the heap will clash with
the vdso. To avoid this map the vdso above the stack and move
STACK_TOP so that it all fits into three level paging.
Sven Schnelle [Wed, 6 Apr 2022 06:35:26 +0000 (08:35 +0200)]
s390/vdso: move vdso mapping to its own function
This is a preparation patch for adding vdso randomization to s390.
It adds a function vdso_size(), which will be used later in calculating
the STACK_TOP value. It also moves the vdso mapping into a new function
vdso_map(), to keep the code similar to other architectures.
Sven Schnelle [Wed, 6 Apr 2022 06:01:24 +0000 (08:01 +0200)]
s390/mmap: increase stack/mmap gap to 128MB
This basically reverts commit 9e78a13bfb16 ("[S390] reduce miminum
gap between stack and mmap_base"). 32MB is not enough space
between stack and mmap for some programs. Given that compat
task aren't common these days, lets revert back to 128MB.
This patch tries to fix as much as possible of the
checkpatch.pl --strict findings:
CHECK: Logical continuations should be on the previous line
CHECK: No space is necessary after a cast
CHECK: Alignment should match open parenthesis
CHECK: 'useable' may be misspelled - perhaps 'usable'?
WARNING: Possible repeated word: 'is'
CHECK: spaces preferred around that '*' (ctx:VxV)
CHECK: Comparison to NULL could be written "!msg"
CHECK: Prefer kzalloc(sizeof(*zc)...) over kzalloc(sizeof(struct...)...)
CHECK: Unnecessary parentheses around resp_type->work
CHECK: Avoid CamelCase: <xcRB>
There is no functional change comming with this patch, only
code cleanup, renaming, whitespaces, indenting, ... but no
semantic change in any way. Also the API (zcrypt and pkey
header file) is semantically unchanged.
This patch does a little cleanup on the CPRBX struct
in zcrypt.h and the redundant CPRB struct definition in
zcrypt_msgtype6.c. Especially some of the misleading
fields from the CPRBX struct have been removed.
There is no semantic change coming with this patch.
The field names changed in the XCRB struct are only related
to reserved fields which should never been used.
This patch introduces user space notifications for changes
on the apmask or aqmask attributes. So it could be possible
to write a udev rule to load/unload the vfio_ap kernel module
based on changes of these masks.
On chance of the apmask or aqmask an AP change event will
be produced with an uevent environment variable showing
the new APMASK or AQMASK mask.
So a change on the apmask triggers an uvevent like this:
Only real changes to the masks are processed - the old and
new masks are compared and no action is done if the values
are equal (and thus no uevent). The emit of the uevent is
the very last action done when a mask change is processed.
However, there is no guarantee that all unbind/bind actions
caused by the apmask/aqmask changes are completed when the
apmask/aqmask change uevent is received in userspace.
Signed-off-by: Harald Freudenberger <freude@linux.ibm.com> Tested-by: Thomas Huth <thuth@redhat.com> Reviewed-by: Jürgen Christ <jchrist@linux.ibm.com> Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
s390/zcrypt: add display of ASYM master key verification pattern
This patch extends the sysfs attribute mkvps for CCA cards
to show the states and master key verification patterns for
the old, current and new ASYM master key registers.
With this patch now all relevant master key verification
patterns related to a CCA HSM are available with the mkvps
sysfs attribute. This is a requirement for some exploiters
like the kubernetes cex plugin or initrd code needing to
verify the master key verification patterns on HSMs before
use.
s390/kexec: set end-of-ipl flag in last diag308 call
If the facility IPL-complete-control is present then the last diag308
call made by kexec shall set the end-of-ipl flag in the subcode register
to signal the hypervisor that this is the last diag308 call made by Linux.
Only the diag308 calls made during a regular kexec need to set
the end-of-ipl flag, in all other cases the hypervisor will ignore it.
Revert "arm64: dts: tegra: Fix boolean properties with values"
This reverts commit 1a67653de0dd, which caused a boot regression.
The behavior of the "drive-push-pull" in the kernel does not
match what the binding document describes. Revert Rob's patch
to make the DT match the kernel again, rather than the binding.
Fixes: 5b0b9e4c2c89 ("tcp: md5: incorrect tcp_header_len for incoming connections") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Francesco Ruggeri <fruggeri@arista.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Mon, 25 Apr 2022 00:34:07 +0000 (17:34 -0700)]
tcp: fix potential xmit stalls caused by TCP_NOTSENT_LOWAT
I had this bug sitting for too long in my pile, it is time to fix it.
Thanks to Doug Porter for reminding me of it!
We had various attempts in the past, including commit 0cbe6a8f089e ("tcp: remove SOCK_QUEUE_SHRUNK"),
but the issue is that TCP stack currently only generates
EPOLLOUT from input path, when tp->snd_una has advanced
and skb(s) cleaned from rtx queue.
If a flow has a big RTT, and/or receives SACKs, it is possible
that the notsent part (tp->write_seq - tp->snd_nxt) reaches 0
and no more data can be sent until tp->snd_una finally advances.
What is needed is to also check if POLLOUT needs to be generated
whenever tp->snd_nxt is advanced, from output path.
This bug triggers more often after an idle period, as
we do not receive ACK for at least one RTT. tcp_notsent_lowat
could be a fraction of what CWND and pacing rate would allow to
send during this RTT.
In a followup patch, I will remove the bogus call
to tcp_chrono_stop(sk, TCP_CHRONO_SNDBUF_LIMITED)
from tcp_check_space(). Fact that we have decided to generate
an EPOLLOUT does not mean the application has immediately
refilled the transmit queue. This optimistic call
might have been the reason the bug seemed not too serious.
Tested:
200 ms rtt, 1% packet loss, 32 MB tcp_rmem[2] and tcp_wmem[2]
$ echo 500000 >/proc/sys/net/ipv4/tcp_notsent_lowat
$ cat bench_rr.sh
SUM=0
for i in {1..10}
do
V=`netperf -H remote_host -l30 -t TCP_RR -- -r 10000000,10000 -o LOCAL_BYTES_SENT | egrep -v "MIGRATED|Bytes"`
echo $V
SUM=$(($SUM + $V))
done
echo SUM=$SUM
Fixes: e968b1b3e9b8 ("arp: Remove #ifdef CONFIG_PROC_FS") Reported-by: kernel test robot <lkp@intel.com> Signed-off-by: Yajun Deng <yajun.deng@linux.dev> Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Thu, 21 Apr 2022 23:01:05 +0000 (02:01 +0300)]
net: mscc: ocelot: don't add VID 0 to ocelot->vlans when leaving VLAN-aware bridge
DSA, through dsa_port_bridge_leave(), first notifies the port of the
fact that it left a bridge, then, if that bridge was VLAN-aware, it
notifies the port of the change in VLAN awareness state, towards
VLAN-unaware mode.
So ocelot_port_vlan_filtering() can be called when ocelot_port->bridge
is NULL, and this makes ocelot_add_vlan_unaware_pvid() create a struct
ocelot_bridge_vlan with a vid of 0 and an "untagged" setting of true on
that port.
In a way this structure correctly reflects the reality, but by design,
VID 0 (OCELOT_STANDALONE_PVID) was not meant to be kept in the bridge
VLAN list of the driver, but managed separately.
Having OCELOT_STANDALONE_PVID in ocelot->vlans makes us trip up on
several sanity checks that did not expect to have this VID there.
For example, after we leave a VLAN-aware bridge and we re-join it, we
can no longer program egress-tagged VLANs to hardware:
# ip link add br0 type bridge vlan_filtering 1 && ip link set br0 up
# ip link set swp0 master br0
# ip link set swp0 nomaster
# ip link set swp0 master br0
# bridge vlan add dev swp0 vid 100
Error: mscc_ocelot_switch_lib: Port with more than one egress-untagged VLAN cannot have egress-tagged VLANs.
But this configuration is in fact supported by the hardware, since we
could use OCELOT_PORT_TAG_NATIVE. According to its comment:
/* all VLANs except the native VLAN and VID 0 are egress-tagged */
yet when assessing the eligibility for this mode, we do not check for
VID 0 in ocelot_port_uses_native_vlan(), instead we just ensure that
ocelot_port_num_untagged_vlans() == 1. This is simply because VID 0
doesn't have a bridge VLAN structure.
The way I identify the problem is that ocelot_port_vlan_filtering(false)
only means to call ocelot_add_vlan_unaware_pvid() when we dynamically
turn off VLAN awareness for a bridge we are under, and the PVID changes
from the bridge PVID to a reserved PVID based on the bridge number.
Since OCELOT_STANDALONE_PVID is statically added to the VLAN table
during ocelot_vlan_init() and never removed afterwards, calling
ocelot_add_vlan_unaware_pvid() for it is not intended and does not serve
any purpose.
Fix the issue by avoiding the call to ocelot_add_vlan_unaware_pvid(vid=0)
when we're resetting VLAN awareness after leaving the bridge, to become
a standalone port.
Fixes: 54c319846086 ("net: mscc: ocelot: enforce FDB isolation when VLAN-unaware") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Thu, 21 Apr 2022 23:01:04 +0000 (02:01 +0300)]
net: mscc: ocelot: ignore VID 0 added by 8021q module
Both the felix DSA driver and ocelot switchdev driver declare
dev->features & NETIF_F_HW_VLAN_CTAG_FILTER under certain circumstances*,
so the 8021q module will add VID 0 to our RX filter when the port goes
up, to ensure 802.1p traffic is not dropped.
We treat VID 0 as a special value (OCELOT_STANDALONE_PVID) which
deliberately does not have a struct ocelot_bridge_vlan associated with
it. Instead, this gets programmed to the VLAN table in ocelot_vlan_init().
If we allow external calls to modify VID 0, we reach the following
situation:
# ip link add br0 type bridge vlan_filtering 1 && ip link set br0 up
# ip link set swp0 master br0
# ip link set swp0 up # this adds VID 0 to ocelot->vlans with untagged=false
bridge vlan
port vlan-id
swp0 1 PVID Egress Untagged # the bridge also adds VID 1
br0 1 PVID Egress Untagged
# bridge vlan add dev swp0 vid 100 untagged
Error: mscc_ocelot_switch_lib: Port with egress-tagged VLANs cannot have more than one egress-untagged (native) VLAN.
This configuration should have been accepted, because
ocelot_port_manage_port_tag() should select OCELOT_PORT_TAG_NATIVE.
Yet it isn't, because we have an entry in ocelot->vlans which says
VID 0 should be egress-tagged, something the hardware can't do.
Fix this by suppressing additions/deletions on VID 0 and managing this
VLAN exclusively using OCELOT_STANDALONE_PVID.
*DSA toggles it when the port becomes VLAN-aware by joining a VLAN-aware
bridge. Ocelot declares it unconditionally for some reason.
Fixes: 54c319846086 ("net: mscc: ocelot: enforce FDB isolation when VLAN-unaware") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Thu, 21 Apr 2022 22:42:22 +0000 (01:42 +0300)]
net: dsa: flood multicast to CPU when slave has IFF_PROMISC
Certain DSA switches can eliminate flooding to the CPU when none of the
ports have the IFF_ALLMULTI or IFF_PROMISC flags set. This is done by
synthesizing a call to dsa_port_bridge_flags() for the CPU port, a call
which normally comes from the bridge driver via switchdev.
The bridge port flags and IFF_PROMISC|IFF_ALLMULTI have slightly
different semantics, and due to inattention/lack of proper testing, the
IFF_PROMISC flag allows unknown unicast to be flooded to the CPU, but
not unknown multicast.
This must be fixed by setting both BR_FLOOD (unicast) and BR_MCAST_FLOOD
in the synthesized dsa_port_bridge_flags() call, since IFF_PROMISC means
that packets should not be filtered regardless of their MAC DA.
Fixes: 7569459a52c9 ("net: dsa: manage flooding on the CPU ports") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Carlos Bilbao [Tue, 5 Apr 2022 18:32:14 +0000 (13:32 -0500)]
x86/mce: Add messages for panic errors in AMD's MCE grading
When a machine error is graded as PANIC by the AMD grading logic, the
MCE handler calls mce_panic(). The notification chain does not come
into effect so the AMD EDAC driver does not decode the errors. In these
cases, the messages displayed to the user are more cryptic and miss
information that might be relevant, like the context in which the error
took place.
Add messages to the grading logic for machine errors so that it is clear
what error it was.
Peilin Ye [Thu, 21 Apr 2022 22:09:02 +0000 (15:09 -0700)]
ip_gre, ip6_gre: Fix race condition on o_seqno in collect_md mode
As pointed out by Jakub Kicinski, currently using TUNNEL_SEQ in
collect_md mode is racy for [IP6]GRE[TAP] devices. Consider the
following sequence of events:
1. An [IP6]GRE[TAP] device is created in collect_md mode using "ip link
add ... external". "ip" ignores "[o]seq" if "external" is specified,
so TUNNEL_SEQ is off, and the device is marked as NETIF_F_LLTX (i.e.
it uses lockless TX);
2. Someone sets TUNNEL_SEQ on outgoing skb's, using e.g.
bpf_skb_set_tunnel_key() in an eBPF program attached to this device;
3. gre_fb_xmit() or __gre6_xmit() processes these skb's:
Since we are not using the TX lock (&txq->_xmit_lock), multiple CPUs may
try to do this tunnel->o_seqno++ in parallel, which is racy. Fix it by
making o_seqno atomic_t.
As mentioned by Eric Dumazet in commit b790e01aee74 ("ip_gre: lockless
xmit"), making o_seqno atomic_t increases "chance for packets being out
of order at receiver" when NETIF_F_LLTX is on.
Maybe a better fix would be:
1. Do not ignore "oseq" in external mode. Users MUST specify "oseq" if
they want the kernel to allow sequencing of outgoing packets;
2. Reject all outgoing TUNNEL_SEQ packets if the device was not created
with "oseq".
Unfortunately, that would break userspace.
We could now make [IP6]GRE[TAP] devices always NETIF_F_LLTX, but let us
do it in separate patches to keep this fix minimal.
Suggested-by: Jakub Kicinski <kuba@kernel.org> Fixes: 77a5196a804e ("gre: add sequence number for collect md mode.") Signed-off-by: Peilin Ye <peilin.ye@bytedance.com> Acked-by: William Tu <u9012063@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Peilin Ye [Thu, 21 Apr 2022 22:08:38 +0000 (15:08 -0700)]
ip6_gre: Make o_seqno start from 0 in native mode
For IP6GRE and IP6GRETAP devices, currently o_seqno starts from 1 in
native mode. According to RFC 2890 2.2., "The first datagram is sent
with a sequence number of 0." Fix it.
It is worth mentioning that o_seqno already starts from 0 in collect_md
mode, see the "if (tunnel->parms.collect_md)" clause in __gre6_xmit(),
where tunnel->o_seqno is passed to gre_build_header() before getting
incremented.
Fixes: c12b395a4664 ("gre: Support GRE over IPv6") Signed-off-by: Peilin Ye <peilin.ye@bytedance.com> Acked-by: William Tu <u9012063@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Peilin Ye [Thu, 21 Apr 2022 22:07:57 +0000 (15:07 -0700)]
ip_gre: Make o_seqno start from 0 in native mode
For GRE and GRETAP devices, currently o_seqno starts from 1 in native
mode. According to RFC 2890 2.2., "The first datagram is sent with a
sequence number of 0." Fix it.
It is worth mentioning that o_seqno already starts from 0 in collect_md
mode, see gre_fb_xmit(), where tunnel->o_seqno is passed to
gre_build_header() before getting incremented.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Peilin Ye <peilin.ye@bytedance.com> Acked-by: William Tu <u9012063@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Carlos Bilbao [Tue, 5 Apr 2022 18:32:13 +0000 (13:32 -0500)]
x86/mce: Simplify AMD severity grading logic
The MCE handler needs to understand the severity of the machine errors to
act accordingly. Simplify the AMD grading logic following a logic that
closely resembles the descriptions of the public PPR documents. This will
help include more fine-grained grading of errors in the future.
Alex Elder [Thu, 21 Apr 2022 18:53:33 +0000 (13:53 -0500)]
net: ipa: compute proper aggregation limit
The aggregation byte limit for an endpoint is currently computed
based on the endpoint's receive buffer size.
However, some bytes at the front of each receive buffer are reserved
on the assumption that--as with SKBs--it might be useful to insert
data (such as headers) before what lands in the buffer.
The aggregation byte limit currently doesn't take into account that
reserved space, and as a result, aggregation could require space
past that which is available in the buffer.
Fix this by reducing the size used to compute the aggregation byte
limit by the NET_SKB_PAD offset reserved for each receive buffer.
Signed-off-by: Alex Elder <elder@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Carpenter [Thu, 21 Apr 2022 15:49:02 +0000 (18:49 +0300)]
net: ethernet: mtk_eth_soc: add check for allocation failure
Check if the kzalloc() failed.
Fixes: 804775dfc288 ("net: ethernet: mtk_eth_soc: add support for Wireless Ethernet Dispatch (WED)") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Carpenter [Thu, 21 Apr 2022 15:46:13 +0000 (18:46 +0300)]
net: lan966x: fix a couple off by one bugs
The lan966x->ports[] array has lan966x->num_phys_ports elements. These
are assigned in lan966x_probe(). That means the > comparison should be
changed to >=.
The first off by one check is harmless but the second one could lead to
an out of bounds access and a crash.
Fixes: 5ccd66e01cbe ("net: lan966x: add support for interrupts from analyzer") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net/smc: sync err code when tcp connection was refused
In the current implementation, when TCP initiates a connection
to an unavailable [ip,port], ECONNREFUSED will be stored in the
TCP socket, but SMC will not. However, some apps (like curl) use
getsockopt(,,SO_ERROR,,) to get the error information, which makes
them miss the error message and behave strangely.
Fixes: 50717a37db03 ("net/smc: nonblocking connect rework") Signed-off-by: liuyacan <liuyacan@corp.netease.com> Reviewed-by: Tony Lu <tonylu@linux.alibaba.com> Acked-by: Karsten Graul <kgraul@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Schspa Shi [Tue, 19 Apr 2022 01:28:10 +0000 (09:28 +0800)]
gpio: use raw spinlock for gpio chip shadowed data
In case of PREEMPT_RT, there is a raw_spinlock -> spinlock dependency
as the lockdep report shows.
__irq_set_handler
irq_get_desc_buslock
__irq_get_desc_lock
raw_spin_lock_irqsave(&desc->lock, *flags); // raw spinlock get here
__irq_do_set_handler
mask_ack_irq
dwapb_irq_ack
spin_lock_irqsave(&gc->bgpio_lock, flags); // sleep able spinlock
irq_put_desc_busunlock
Replace with a raw lock to avoid BUGs. This lock is only used to access
registers, and It's safe to replace with the raw lock without bad
influence.
PCI: mvebu: Add support for sending Set_Slot_Power_Limit message
If DT supplies the 'slot-power-limit-milliwatt' property, program
the value in the Slot Power Limit in the Slot Capabilities register
and program the Root Port to send a Set_Slot_Power_Limit Message
when the Link transitions to DL_Up.
PCI: Add function for parsing 'slot-power-limit-milliwatt' DT property
Add function of_pci_get_slot_power_limit(), which parses the
'slot-power-limit-milliwatt' DT property, returning the value in
milliwatts and in format ready for the PCIe Slot Capabilities Register.
Link: https://lore.kernel.org/r/20220412094946.27069-4-pali@kernel.org Signed-off-by: Pali Rohár <pali@kernel.org> Signed-off-by: Marek Behún <kabel@kernel.org> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Reviewed-by: Rob Herring <robh@kernel.org> Reviewed-by: Bjorn Helgaas <bhelgaas@google.com>
net: hns3: add return value for mailbox handling in PF
Currently, there are some querying mailboxes sent from VF to PF,
and VF will wait the PF's handling result. For mailbox
HCLGE_MBX_GET_QID_IN_PF and HCLGE_MBX_GET_RSS_KEY, it may fail
when the input parameter is invalid, but the prototype of their
handler function is void. In this case, PF always return success
to VF, which may cause the VF get incorrect result.
Fixes it by adding return value for these function.
Fixes: 63b1279d9905 ("net: hns3: check queue id range before using") Fixes: 532cfc0df1e4 ("net: hns3: add a check for index in hclge_get_rss_key()") Signed-off-by: Jian Shen <shenjian15@huawei.com> Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: hns3: add validity check for message data length
Add validity check for message data length in function
hclge_send_mbx_msg(), avoid unexpected overflow.
Fixes: dde1a86e93ca ("net: hns3: Add mailbox support to PF driver") Signed-off-by: Jian Shen <shenjian15@huawei.com> Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jie Wang [Sun, 24 Apr 2022 12:57:23 +0000 (20:57 +0800)]
net: hns3: modify the return code of hclge_get_ring_chain_from_mbx
Currently, function hclge_get_ring_chain_from_mbx will return -ENOMEM if
ring_num is bigger than HCLGE_MBX_MAX_RING_CHAIN_PARAM_NUM. It is better to
return -EINVAL for the invalid parameter case.
So this patch fixes it by return -EINVAL in this abnormal branch.
Fixes: 5d02a58dae60 ("net: hns3: fix for buffer overflow smatch warning") Signed-off-by: Jie Wang <wangjie125@huawei.com> Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Peng Li [Sun, 24 Apr 2022 12:57:22 +0000 (20:57 +0800)]
net: hns3: fix error log of tx/rx tqps stats
The comments in function hclge_comm_tqps_update_stats is not right,
so fix it.
Fixes: 287db5c40d15 ("net: hns3: create new set of common tqp stats APIs for PF and VF reuse") Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
For debugfs node rx/tx_queue_info and rx/tx_bd_info, their output info is
aligned to the right, it's not aligned with output of other debugfs node,
so uniform their output info.
Fixes: 907676b13071 ("net: hns3: use tx bounce buffer for small packets") Fixes: e44c495d95e0 ("net: hns3: refactor queue info of debugfs") Fixes: 77e9184869c9 ("net: hns3: refactor dump bd info of debugfs") Signed-off-by: Hao Chen <chenhao288@hisilicon.com> Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: hns3: clear inited state and stop client after failed to register netdev
If failed to register netdev, it needs to clear INITED state and stop
client in case of cause problem when concurrency with uninitialized
process of driver.
Fixes: a289a7e5c1d4 ("net: hns3: put off calling register_netdev() until client initialize complete") Signed-off-by: Jian Shen <shenjian15@huawei.com> Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Line card can contain one or more devices that makes sense to make
visible to the user. For example, this can be a gearbox with
flash memory, which could be updated.
Provide the driver possibility to attach such devices to a line card
and expose those to user.
Example:
$ devlink lc show pci/0000:01:00.0 lc 8
pci/0000:01:00.0:
lc 8 state active type 16x100G
supported_types:
16x100G
devices:
device 0
device 1
device 2
device 3
Signed-off-by: Jiri Pirko <jiri@nvidia.com> Signed-off-by: Ido Schimmel <idosch@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
btrfs: Avoid live-lock in search_ioctl() on hardware with sub-page faults
Commit a48b73eca4ce ("btrfs: fix potential deadlock in the search
ioctl") addressed a lockdep warning by pre-faulting the user pages and
attempting the copy_to_user_nofault() in an infinite loop. On
architectures like arm64 with MTE, an access may fault within a page at
a location different from what fault_in_writeable() probed. Since the
sk_offset is rewound to the previous struct btrfs_ioctl_search_header
boundary, there is no guaranteed forward progress and search_ioctl() may
live-lock.
Use fault_in_subpage_writeable() instead of fault_in_writeable() to
ensure the permission is checked at the right granularity (smaller than
PAGE_SIZE).
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Fixes: a48b73eca4ce ("btrfs: fix potential deadlock in the search ioctl") Reported-by: Al Viro <viro@zeniv.linux.org.uk> Acked-by: David Sterba <dsterba@suse.com> Cc: Chris Mason <clm@fb.com> Cc: Josef Bacik <josef@toxicpanda.com> Link: https://lore.kernel.org/r/20220423100751.1870771-4-catalin.marinas@arm.com Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
arm64: Add support for user sub-page fault probing
With MTE, even if the pte allows an access, a mismatched tag somewhere
within a page can still cause a fault. Select ARCH_HAS_SUBPAGE_FAULTS if
MTE is enabled and implement the probe_subpage_writeable() function.
Note that get_user() is sufficient for the writeable MTE check since the
same tag mismatch fault would be triggered by a read. The caller of
probe_subpage_writeable() will need to check the pte permissions
(put_user, GUP).
mm: Add fault_in_subpage_writeable() to probe at sub-page granularity
On hardware with features like arm64 MTE or SPARC ADI, an access fault
can be triggered at sub-page granularity. Depending on how the
fault_in_writeable() function is used, the caller can get into a
live-lock by continuously retrying the fault-in on an address different
from the one where the uaccess failed.
In the majority of cases progress is ensured by the following
conditions:
1. copy_to_user_nofault() guarantees at least one byte access if the
user address is not faulting.
2. The fault_in_writeable() loop is resumed from the first address that
could not be accessed by copy_to_user_nofault().
If the loop iteration is restarted from an earlier (initial) point, the
loop is repeated with the same conditions and it would live-lock.
Introduce an arch-specific probe_subpage_writeable() and call it from
the newly added fault_in_subpage_writeable() function. The arch code
with sub-page faults will have to implement the specific probing
functionality.
Note that no other fault_in_subpage_*() functions are added since they
have no callers currently susceptible to a live-lock.
drm/display: Move SCDC helpers into display-helper library
SCDC is the Status and Control Data Channel for HDMI. Move the SCDC
helpers into display/ and split the header into files for core and
helpers. Update all affected drivers. No functional changes.
To avoid the proliferation of Kconfig options, SCDC is part of DRM's
support for HDMI. If necessary, a new option could make SCDC an
independent feature.
drm/display: Move HDMI helpers into display-helper module
Move DRM's HMDI helpers into the display/ subdirectoy and add it
to DRM's display helpers. Update all affected drivers. No functional
changes.
The HDMI helpers were implemented in the EDID and connector code, but
are actually unrelated. With the move to the display-helper library, we
can remove the dependency on drm_edid.{c,h} in some driver's HDMI source
files.
Several of the HDMI helpers remain in EDID code because both share parts
of their implementation internally. With better refractoring of the EDID
code, those HDMI helpers could be moved into the display-helper library
as well.
drm/display: Move HDCP helpers into display-helper module
Move DRM's HDCP helper library into the display/ subdirectory and add
it to DRM's display helpers. Split the header file into core and helpers.
Update all affected drivers. No functional changes.
drm/display: Move DSC header and helpers into display-helper module
DSC is the Display Stream Compression standard for DisplayPort. Move
the DSC code into display/ and split the header into files for protocol
core and DRM helpers. Adapt all users of the code. No functional
changes.
To avoid the proliferation of Kconfig options, DSC is part of DRM's
support for DisplayPort. If necessary, a new option could make DSC an
independent feature.
drm/display: Split DisplayPort header into core and helper
Move DisplayPort protocol constants and structures into the new
header drm_dp.h, which can be used by DRM core components. The
existing header drm_dp_helper.h now only contains helper code for
graphics drivers. No functional changes.
drm/display: Introduce a DRM display-helper module
Replace the DP-helper module with a display-helper module. The
support for DisplayPort becomes an internal option that drivers
have to select. Update all related Kconfig and Makefile rules.
Besides the existing code for DisplayPort, the new module will
contain helpers for other video-output standards, such as HDMI.
Drivers will have to select their required video-output helpers.
Linking all display-related code into a single module avoids the
proliferation of small kernel modules.
The module parameters drm_dp_cec_unregister_delay, dp_aux_i2c_speed_khz,
and dp_aux_i2c_transfer_size are moving from the drm_dp_helper namespace
to drm_display_helper.
v2:
* mention module parameters in commit message (Javier)
* distiguish between display module and DP support in Kconfig
* update Makefile rules for DP helpers
* move Kconfig rules into separate file under display/
Rename dp/ to display/ to account for additional display-related
helpers, such as HDMI. Update all related include statements. No
functional changes.
Various drivers, such as i915 and amdgpu, use similar naming scheme
by putting code for video-output standards into a local display/
directory. The new directory's name is aligned with this convention.
Martin Willi [Tue, 19 Apr 2022 13:47:00 +0000 (15:47 +0200)]
netfilter: Update ip6_route_me_harder to consider L3 domain
The commit referenced below fixed packet re-routing if Netfilter mangles
a routing key property of a packet and the packet is routed in a VRF L3
domain. The fix, however, addressed IPv4 re-routing, only.
This commit applies the same behavior for IPv6. While at it, untangle
the nested ternary operator to make the code more readable.
Fixes: 6d8b49c3a3a3 ("netfilter: Update ip_route_me_harder to consider L3 domain") Cc: stable@vger.kernel.org Signed-off-by: Martin Willi <martin@strongswan.org> Reviewed-by: David Ahern <dsahern@kernel.org> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
projects / people / ms / linux.git / log
