bootgraph:
- fix parsing of /proc/version to be much more flexible
- check kernel version to disallow ftrace on anything older than 4.10
sleepgraph:
- include fix to bugzilla 212761 in case it regresses
- fix for -proc bug: https://github.com/intel/pm-graph/pull/20
- add -debugtiming arg to get timestamps on prints
- allow use of the netfix tool hosted in the github repo
- read s0ix data from pmc_core for better debug
- include more system data in the output log
- Do a better job testing input files useability
- flag more error data from dmesg in the timeline
- pre-parse the trace log to fix any ordering issues
- add new parser to process dmesg only timelines
- remove superflous sleep(5) in multitest mode
config/custom-timeline-functions.cfg:
- change some names to keep up to date
README:
- new version, small wording changes
Signed-off-by: Todd Brandt <todd.e.brandt@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM fixes from Paolo Bonzini:
"RISC-V:
- Fix missing PAGE_PFN_MASK
- Fix SRCU deadlock caused by kvm_riscv_check_vcpu_requests()
x86:
- Fix for nested virtualization when TSC scaling is active
- Estimate the size of fastcc subroutines conservatively, avoiding
disastrous underestimation when return thunks are enabled
- Avoid possible use of uninitialized fields of 'struct
kvm_lapic_irq'
Generic:
- Mark as such the boolean values available from the statistics file
descriptors
- Clarify statistics documentation"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: emulate: do not adjust size of fastop and setcc subroutines
KVM: x86: Fully initialize 'struct kvm_lapic_irq' in kvm_pv_kick_cpu_op()
Documentation: kvm: clarify histogram units
kvm: stats: tell userspace which values are boolean
x86/kvm: fix FASTOP_SIZE when return thunks are enabled
KVM: nVMX: Always enable TSC scaling for L2 when it was enabled for L1
RISC-V: KVM: Fix SRCU deadlock caused by kvm_riscv_check_vcpu_requests()
riscv: Fix missing PAGE_PFN_MASK
Merge tag 'ceph-for-5.19-rc7' of https://github.com/ceph/ceph-client
Pull ceph fix from Ilya Dryomov:
"A folio locking fixup that Xiubo and David cooperated on, marked for
stable. Most of it is in netfs but I picked it up into ceph tree on
agreement with David"
* tag 'ceph-for-5.19-rc7' of https://github.com/ceph/ceph-client:
netfs: do not unlock and put the folio twice
Merge tag 'spi-fix-v5.19-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"A few driver specific fixes, none especially remarkable, plus a
MAINTAINERS file update due to the previous maintainer for the NXP
FSPI driver having left the company"
* tag 'spi-fix-v5.19-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: cadence-quadspi: Remove spi_master_put() in probe failure path
MAINTAINERS: change the NXP FSPI driver maintainer.
spi: amd: Limit max transfer and message size
spi: aspeed: Fix division by zero
spi: aspeed: Add dev_dbg() to dump the spi-mem direct mapping descriptor
Mark Brown [Fri, 15 Jul 2022 17:21:09 +0000 (18:21 +0100)]
Read _SUB from ACPI to be able to identify firmware
Merge series from Stefan Binding <sbinding@opensource.cirrus.com>:
CS35L41 has a DSP which is able to run firmware, as well as a tuning file.
Different systems may want to use different firmwares and tuning files, and
some firmwares/tunings may not be compatible with other systems.
To allow a system to select the correct fimware/tuning, we can read an _SUB
from the ACPI. This _SUB can then be used to uniquely identify the system
in the firmware/tuning file name.
Add a helper function which reads the _SUB, so this can be used by other
parts in the future.
Add support inside the CS35L41 ASoC driver to read this _SUB, and save it
appropriately.
With the new design in place, the show() and store() callbacks check if
the policy is active or not before proceeding any further to avoid
potential races. And in order to guarantee that cpufreq_policy_free()
must be called after clearing the policy->cpus mask, i.e. by marking the
policy inactive.
In order to avoid introducing a bug around this later, print a warning
message if we end up freeing an active policy.
Also update cpufreq_online() a bit to make sure we clear the cpus mask
for each error case before calling cpufreq_policy_free().
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Lukasz Luba [Thu, 7 Jul 2022 07:15:55 +0000 (08:15 +0100)]
cpufreq: scmi: Support the power scale in micro-Watts in SCMI v3.1
The SCMI v3.1 adds support for power values in micro-Watts. They are not
always in milli-Watts anymore (ignoring the bogo-Watts). Thus, the power
must be converted conditionally before sending to Energy Model. Add the
logic which handles the needed checks and conversions.
Acked-by: Sudeep Holla <sudeep.holla@arm.com> Signed-off-by: Lukasz Luba <lukasz.luba@arm.com> Acked-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Lukasz Luba [Thu, 7 Jul 2022 07:15:54 +0000 (08:15 +0100)]
firmware: arm_scmi: Get detailed power scale from perf
In SCMI v3.1 the power scale can be in micro-Watts. The upper layers, e.g.
cpufreq and EM should handle received power values properly (upscale when
needed). Thus, provide an interface which allows to check what is the
scale for power values. The old interface allowed to distinguish between
bogo-Watts and milli-Watts only (which was good for older SCMI spec).
Acked-by: Sudeep Holla <sudeep.holla@arm.com> Signed-off-by: Lukasz Luba <lukasz.luba@arm.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Lukasz Luba [Thu, 7 Jul 2022 07:15:53 +0000 (08:15 +0100)]
Documentation: EM: Switch to micro-Watts scale
The EM now uses the micro-Watts scale for the power values. Update
related documentation to reflect that fact.
Fix also a problematic sentence in the doc "to:" which triggers test
scripts complaining about wrong email address.
Reviewed-by: Daniel Lezcano <daniel.lezcano@linaro.org> Signed-off-by: Lukasz Luba <lukasz.luba@arm.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Lukasz Luba [Thu, 7 Jul 2022 07:15:52 +0000 (08:15 +0100)]
PM: EM: convert power field to micro-Watts precision and align drivers
The milli-Watts precision causes rounding errors while calculating
efficiency cost for each OPP. This is especially visible in the 'simple'
Energy Model (EM), where the power for each OPP is provided from OPP
framework. This can cause some OPPs to be marked inefficient, while
using micro-Watts precision that might not happen.
Update all EM users which access 'power' field and assume the value is
in milli-Watts.
Solve also an issue with potential overflow in calculation of energy
estimation on 32bit machine. It's needed now since the power value
(thus the 'cost' as well) are higher.
Example calculation which shows the rounding error and impact:
power = 'dyn-power-coeff' * volt_mV * volt_mV * freq_MHz
The 'cost_b_mW' (which is based on old milli-Watts) is misleadingly
better that the 'cost_b_uW' (this patch uses micro-Watts) and such
would have impact on the 'inefficient OPPs' information in the Cpufreq
framework. This patch set removes the rounding issue.
Signed-off-by: Lukasz Luba <lukasz.luba@arm.com> Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org> Acked-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Revert the xarray conversion, there's a problem with potential
sleep-inside-spinlock [1] when calling xa_insert that triggers GFP_NOFS
allocation. The radix tree used the preloading mechanism to avoid
sleeping but this is not available in xarray.
Conversion from spin lock to mutex is possible but at time of rc6 is
riskier than a clean revert.
Revert the xarray conversion, there's a problem with potential
sleep-inside-spinlock [1] when calling xa_insert that triggers GFP_NOFS
allocation. The radix tree used the preloading mechanism to avoid
sleeping but this is not available in xarray.
Conversion from spin lock to mutex is possible but at time of rc6 is
riskier than a clean revert.
Revert the xarray conversion, there's a problem with potential
sleep-inside-spinlock [1] when calling xa_insert that triggers GFP_NOFS
allocation. The radix tree used the preloading mechanism to avoid
sleeping but this is not available in xarray.
Conversion from spin lock to mutex is possible but at time of rc6 is
riskier than a clean revert.
Revert the xarray conversion, there's a problem with potential
sleep-inside-spinlock [1] when calling xa_insert that triggers GFP_NOFS
allocation. The radix tree used the preloading mechanism to avoid
sleeping but this is not available in xarray.
Conversion from spin lock to mutex is possible but at time of rc6 is
riskier than a clean revert.
Merge tag 'platform-drivers-x86-v5.19-4' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86
Pull x86 platform driver fixes from Hans de Goede:
"Highlights:
- Fix brightness key events getting reported twice on some Dells.
Regression caused by recent Panasonic hotkey fixes
- Fix poweroff no longer working on some devices regression caused
by recent poweroff handler rework
- Mark new (in 5.19) Intel IFS driver as broken, because of some
issues surrounding the userspace (sysfs) API which need to be
cleared up
- Some hardware-id / quirk additions"
* tag 'platform-drivers-x86-v5.19-4' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86:
ACPI: video: Fix acpi_video_handles_brightness_key_presses()
platform/x86: intel_atomisp2_led: Also turn off the always-on camera LED on the Asus T100TAF
platform/x86/intel/ifs: Mark as BROKEN
platform/x86: asus-wmi: Add key mappings
efi: Fix efi_power_off() not being run before acpi_power_off() when necessary
platform/x86: x86-android-tablets: Fix Lenovo Yoga Tablet 2 830/1050 poweroff again
platform/x86: gigabyte-wmi: add support for B660I AORUS PRO DDR4
platform/x86/amd/pmc: Add new platform support
platform/x86/amd/pmc: Add new acpi id for PMC controller
Merge tag 'drm-fixes-2022-07-15' of git://anongit.freedesktop.org/drm/drm
Pull drm fixes from Dave Airlie:
"This is the regular fixes pull for this week. This has a bunch of
amdgpu fixes, major one reverts the buddy allocator until it can be
tested more, otherwise just small ones, then i915 has a bunch of
fixes.
The outstanding firmware regressions reported by phoronix will
hopefully be dealt with ASAP.
amdgpu:
- revert buddy allocator support for now
- DP MST blank screen fix for specific platforms
- MEC firmware check fix for GC 10.3.7
- Deep color fix for DCE
- Fix possible divide by 0
- Coverage blend mode fix
- Fix cursor only commit timestamps
i915:
- Selftest fix
- TTM fix sg_table construction
- Error return fixes
- Fix a performance regression related to waitboost
- Fix GT resets"
* tag 'drm-fixes-2022-07-15' of git://anongit.freedesktop.org/drm/drm:
drm/amd/display: Ensure valid event timestamp for cursor-only commits
drm/amd/display: correct check of coverage blend mode
drm/amd/pm: Prevent divide by zero
drm/amd/display: Only use depth 36 bpp linebuffers on DCN display engines.
drm/amdkfd: correct the MEC atomic support firmware checking for GC 10.3.7
drm/amd/display: Ignore First MST Sideband Message Return Error
drm/i915/selftests: fix subtraction overflow bug
drm/i915/gem: Look for waitboosting across the whole object prior to individual waits
drm/i915/gt: Serialize TLB invalidates with GT resets
drm/i915/gt: Serialize GRDOM access between multiple engine resets
drm/i915/ttm: fix sg_table construction
drm/i915/selftests: fix a couple IS_ERR() vs NULL tests
drm/i915: Fix vm use-after-free in vma destruction
drm/i915/guc: ADL-N should use the same GuC FW as ADL-S
drm/i915: fix a possible refcount leak in intel_dp_add_mst_connector()
drm/i915/gvt: IS_ERR() vs NULL bug in intel_gvt_update_reg_whitelist()
Revert "drm/amdgpu: add drm buddy support to amdgpu"
Ben Dooks [Thu, 14 Jul 2022 10:03:22 +0000 (11:03 +0100)]
bpf: Fix check against plain integer v 'NULL'
When checking with sparse, btf_show_type_value() is causing a
warning about checking integer vs NULL when the macro is passed
a pointer, due to the 'value != 0' check. Stop sparse complaining
about any type-casting by adding a cast to the typeof(value).
This fixes the following sparse warnings:
kernel/bpf/btf.c:2579:17: warning: Using plain integer as NULL pointer
kernel/bpf/btf.c:2581:17: warning: Using plain integer as NULL pointer
kernel/bpf/btf.c:3407:17: warning: Using plain integer as NULL pointer
kernel/bpf/btf.c:3758:9: warning: Using plain integer as NULL pointer
Merge tag 'sysctl-fixes-5.19-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/mcgrof/linux
Pyll sysctl fix from Luis Chamberlain:
"Only one fix for sysctl"
* tag 'sysctl-fixes-5.19-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/mcgrof/linux:
mm: sysctl: fix missing numa_stat when !CONFIG_HUGETLB_PAGE
media: uapi: move HEVC stateless controls out of staging
HEVC uAPI is used by 2 mainline drivers (Hantro, Cedrus)
and at least 2 out-of-tree drivers (rkvdec, RPi).
The uAPI has been reviewed so it is time to make it 'public' by
un-staging it.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@collabora.com> Reviewed-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar> Acked-by: Nicolas Dufresne <nicolas.dufresne@collabora.com> Tested-by: Jernej Skrabec <jernej.skrabec@gmail.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
'F.7.3.6.1 General slice segment header syntax' section of HEVC
specification describes that a slice header always end aligned on
byte boundary, therefore we only need to provide the data offset in bytes.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@collabora.com> Reviewed-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar> Acked-by: Nicolas Dufresne <nicolas.dufresne@collabora.com> Tested-by: Jernej Skrabec <jernej.skrabec@gmail.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
media: hantro: Stop using Hantro dedicated control
The number of bits to skip in the slice header can be computed
in the driver by using sps, pps and decode_params information.
This makes it possible to remove Hantro dedicated control.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@collabora.com> Reviewed-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar> Acked-by: Nicolas Dufresne <nicolas.dufresne@collabora.com> Tested-by: Jernej Skrabec <jernej.skrabec@gmail.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
media: uapi: Add V4L2_CID_STATELESS_HEVC_ENTRY_POINT_OFFSETS control
The number of 'entry point offset' can be very variable.
Instead of using a large static array define a v4l2 dynamic array
of U32 (V4L2_CTRL_TYPE_U32).
The number of entry point offsets is reported by the elems field
and in struct v4l2_ctrl_hevc_slice_params.num_entry_point_offsets
field.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@collabora.com> Acked-by: Nicolas Dufresne <nicolas.dufresne@collabora.com> Tested-by: Jernej Skrabec <jernej.skrabec@gmail.com> Reviewed-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Michal Suchanek [Thu, 14 Jul 2022 13:40:27 +0000 (21:40 +0800)]
kexec, KEYS, s390: Make use of built-in and secondary keyring for signature verification
commit e23a8020ce4e ("s390/kexec_file: Signature verification prototype")
adds support for KEXEC_SIG verification with keys from platform keyring
but the built-in keys and secondary keyring are not used.
Add support for the built-in keys and secondary keyring as x86 does.
arm64: kexec_file: use more system keyrings to verify kernel image signature
Currently, when loading a kernel image via the kexec_file_load() system
call, arm64 can only use the .builtin_trusted_keys keyring to verify
a signature whereas x86 can use three more keyrings i.e.
.secondary_trusted_keys, .machine and .platform keyrings. For example,
one resulting problem is kexec'ing a kernel image would be rejected
with the error "Lockdown: kexec: kexec of unsigned images is restricted;
see man kernel_lockdown.7".
This patch set enables arm64 to make use of the same keyrings as x86 to
verify the signature kexec'ed kernel image.
Fixes: 732b7b93d849 ("arm64: kexec_file: add kernel signature verification support") Cc: stable@vger.kernel.org # 105e10e2cf1c: kexec_file: drop weak attribute from functions Cc: stable@vger.kernel.org # 34d5960af253: kexec: clean up arch_kexec_kernel_verify_sig Cc: stable@vger.kernel.org # 83b7bb2d49ae: kexec, KEYS: make the code in bzImage64_verify_sig generic Acked-by: Baoquan He <bhe@redhat.com> Cc: kexec@lists.infradead.org Cc: keyrings@vger.kernel.org Cc: linux-security-module@vger.kernel.org Co-developed-by: Michal Suchanek <msuchanek@suse.de> Signed-off-by: Michal Suchanek <msuchanek@suse.de> Acked-by: Will Deacon <will@kernel.org> Signed-off-by: Coiby Xu <coxu@redhat.com> Signed-off-by: Mimi Zohar <zohar@linux.ibm.com>
kexec, KEYS: make the code in bzImage64_verify_sig generic
commit 278311e417be ("kexec, KEYS: Make use of platform keyring for
signature verify") adds platform keyring support on x86 kexec but not
arm64.
The code in bzImage64_verify_sig uses the keys on the
.builtin_trusted_keys, .machine, if configured and enabled,
.secondary_trusted_keys, also if configured, and .platform keyrings
to verify the signed kernel image as PE file.
Before commit 105e10e2cf1c ("kexec_file: drop weak attribute from
functions"), there was already no arch-specific implementation
of arch_kexec_kernel_verify_sig. With weak attribute dropped by that
commit, arch_kexec_kernel_verify_sig is completely useless. So clean it
up.
Note later patches are dependent on this patch so it should be backported
to the stable tree as well.
Cc: stable@vger.kernel.org Suggested-by: Eric W. Biederman <ebiederm@xmission.com> Reviewed-by: Michal Suchanek <msuchanek@suse.de> Acked-by: Baoquan He <bhe@redhat.com> Signed-off-by: Coiby Xu <coxu@redhat.com>
[zohar@linux.ibm.com: reworded patch description "Note"] Link: https://lore.kernel.org/linux-integrity/20220714134027.394370-1-coxu@redhat.com/ Signed-off-by: Mimi Zohar <zohar@linux.ibm.com>
Drop __weak attribute from functions in kexec_core.c:
- machine_kexec_post_load()
- arch_kexec_protect_crashkres()
- arch_kexec_unprotect_crashkres()
- crash_free_reserved_phys_range()
As requested
(http://lkml.kernel.org/r/87ee0q7b92.fsf@email.froward.int.ebiederm.org),
this series converts weak functions in kexec to use the #ifdef approach.
Quoting the 3e35142ef99fe ("kexec_file: drop weak attribute from
arch_kexec_apply_relocations[_add]") changelog:
: Since commit d1bcae833b32f1 ("ELF: Don't generate unused section symbols")
: [1], binutils (v2.36+) started dropping section symbols that it thought
: were unused. This isn't an issue in general, but with kexec_file.c, gcc
: is placing kexec_arch_apply_relocations[_add] into a separate
: .text.unlikely section and the section symbol ".text.unlikely" is being
: dropped. Due to this, recordmcount is unable to find a non-weak symbol in
: .text.unlikely to generate a relocation record against.
This patch (of 2);
Drop __weak attribute from functions in kexec_file.c:
- arch_kexec_kernel_image_probe()
- arch_kimage_file_post_load_cleanup()
- arch_kexec_kernel_image_load()
- arch_kexec_locate_mem_hole()
- arch_kexec_kernel_verify_sig()
arch_kexec_kernel_image_load() calls into kexec_image_load_default(), so
drop the static attribute for the latter.
arch_kexec_kernel_verify_sig() is not overridden by any architecture, so
drop the __weak attribute.
ASoC: SOF: Intel: enable dmic handling with 2 or fewer SoundWire links
When PCH-attached DMICs are used on a SoundWire-based platform, all
known devices pin-mux SoundWire link2 and link3 with DMIC, and only
use link0 and link1 for SoundWire.
The HP Omen16 is the first exception to the rule, with SoundWire using
link0 and link3. Rather than using a fixed mask, let's count the
number of SoundWire links used.
ASoC: Intel: sof_sdw: avoid oops in error handling
While tinkering with ACPI work-arounds for the HP Omen 16 support, we
identified a corner case where the headset codec device properties are
not set in the codec .init when -EPROBE_DEFER is returned, but
released unconditionally in the .exit().
A similar error case can occur if the addition of the device property
fails. We need to test if the property was successfully added before
removing it.
mtd: rawnand: gpmi: Set WAIT_FOR_READY timeout based on program/erase times
06781a5026350 Fixes the calculation of the DEVICE_BUSY_TIMEOUT register
value from busy_timeout_cycles. busy_timeout_cycles is calculated wrong
though: It is calculated based on the maximum page read time, but the
timeout is also used for page write and block erase operations which
require orders of magnitude bigger timeouts.
Fix this by calculating busy_timeout_cycles from the maximum of
tBERS_max and tPROG_max.
This is for now the easiest and most obvious way to fix the driver.
There's room for improvements though: The NAND_OP_WAITRDY_INSTR tells us
the desired timeout for the current operation, so we could program the
timeout dynamically for each operation instead of setting a fixed
timeout. Also we could wire up the interrupt handler to actually detect
and forward timeouts occurred when waiting for the chip being ready.
As a sidenote I verified that the change in 06781a5026350 is really
correct. I wired up the interrupt handler in my tree and measured the
time between starting the operation and the timeout interrupt handler
coming in. The time increases 41us with each step in the timeout
register which corresponds to 4096 clock cycles with the 99MHz clock
that I have.
Fixes: 06781a5026350 ("mtd: rawnand: gpmi: Fix setting busy timeout setting") Fixes: b1206122069aa ("mtd: rawniand: gpmi: use core timings instead of an empirical derivation") Cc: stable@vger.kernel.org Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Acked-by: Han Xu <han.xu@nxp.com> Tested-by: Tomasz Moń <tomasz.mon@camlingroup.com> Signed-off-by: Richard Weinberger <richard@nod.at>
Phil Auld [Fri, 15 Jul 2022 13:49:24 +0000 (09:49 -0400)]
drivers/base: fix userspace break from using bin_attributes for cpumap and cpulist
Using bin_attributes with a 0 size causes fstat and friends to return that
0 size. This breaks userspace code that retrieves the size before reading
the file. Rather than reverting 75bd50fa841 ("drivers/base/node.c: use
bin_attribute to break the size limitation of cpumap ABI") let's put in a
size value at compile time.
For cpulist the maximum size is on the order of
NR_CPUS * (ceil(log10(NR_CPUS)) + 1)/2
which for 8192 is 20480 (8192 * 5)/2. In order to get near that you'd need
a system with every other CPU on one node. For example: (0,2,4,8, ... ).
To simplify the math and support larger NR_CPUS in the future we are using
(NR_CPUS * 7)/2. We also set it to a min of PAGE_SIZE to retain the older
behavior for smaller NR_CPUS.
The cpumap file the size works out to be NR_CPUS/4 + NR_CPUS/32 - 1
(or NR_CPUS * 9/32 - 1) including the ","s.
Add a set of macros for these values to cpumask.h so they can be used in
multiple places. Apply these to the handful of such files in
drivers/base/topology.c as well as node.c.
As an example, on an 80 cpu 4-node system (NR_CPUS == 8192):
include/linux/firmware/intel/stratix10-svc-client.h:55: warning: This comment
starts with '/**', but isn't a kernel-doc comment. Refer
Documentation/doc-guide/kernel-doc.rst
* Flag bit for COMMAND_RECONFIG
media: uapi: HEVC: Define V4L2_CID_STATELESS_HEVC_SLICE_PARAMS as a dynamic array
Make explicit that V4L2_CID_STATELESS_HEVC_SLICE_PARAMS control is
a dynamic array control type.
Some drivers may be able to receive multiple slices in one control
to improve decoding performance.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@collabora.com> Reviewed-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
x86/olpc: fix 'logical not is only applied to the left hand side'
The bitops compile-time optimization series revealed one more
problem in olpc-xo1-sci.c:send_ebook_state(), resulted in GCC
warnings:
arch/x86/platform/olpc/olpc-xo1-sci.c: In function 'send_ebook_state':
arch/x86/platform/olpc/olpc-xo1-sci.c:83:63: warning: logical not is only applied to the left hand side of comparison [-Wlogical-not-parentheses]
83 | if (!!test_bit(SW_TABLET_MODE, ebook_switch_idev->sw) == state)
| ^~
arch/x86/platform/olpc/olpc-xo1-sci.c:83:13: note: add parentheses around left hand side expression to silence this warning
Despite this code working as intended, this redundant double
negation of boolean value, together with comparing to `char`
with no explicit conversion to bool, makes compilers think
the author made some unintentional logical mistakes here.
Make it the other way around and negate the char instead
to silence the warnings.
Fixes: d2aa37411b8e ("x86/olpc/xo1/sci: Produce wakeup events for buttons and switches") Cc: stable@vger.kernel.org # 3.5+ Reported-by: Guenter Roeck <linux@roeck-us.net> Reported-by: kernel test robot <lkp@intel.com> Reviewed-and-tested-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Alexander Lobakin <alexandr.lobakin@intel.com> Signed-off-by: Yury Norov <yury.norov@gmail.com>
The possible values for the field_pic field in the v4l2_hevc_dpb_entry
structure are defined in the table D.2 in HEVC specification section D.3.3.
Add flags and documentation for each of them.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@collabora.com> Reviewed-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar> Acked-by: Nicolas Dufresne <nicolas.dufresne@collabora.com> Tested-by: Jernej Skrabec <jernej.skrabec@gmail.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
media: uapi: HEVC: Change pic_order_cnt definition in v4l2_hevc_dpb_entry
The HEVC specification describes the following:
"PicOrderCntVal is derived as follows:
PicOrderCntVal = PicOrderCntMsb + slice_pic_order_cnt_lsb
The value of PicOrderCntVal shall be in the range of
−2^31 to 2^31 − 1, inclusive."
To match with these definitions change __u16 pic_order_cnt[2]
into __s32 pic_order_cnt_val.
Change v4l2_ctrl_hevc_slice_params->slice_pic_order_cnt to __s32 too.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@collabora.com> Reviewed-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar> Acked-by: Nicolas Dufresne <nicolas.dufresne@collabora.com> Tested-by: Jernej Skrabec <jernej.skrabec@gmail.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
media: uapi: HEVC: Add missing fields in HEVC controls
Complete the HEVC controls with missing fields from H.265 specifications.
Even if these fields aren't used by the current mainlined drivers
they will be required for (at least) the rkvdec driver.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@collabora.com> Reviewed-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar> Acked-by: Nicolas Dufresne <nicolas.dufresne@collabora.com> Tested-by: Jernej Skrabec <jernej.skrabec@gmail.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Hans Verkuil [Fri, 8 Jul 2022 16:21:41 +0000 (17:21 +0100)]
media: v4l2-ctrls: add support for dynamically allocated arrays.
Implement support for dynamically allocated arrays.
Most of the changes concern keeping track of the number of elements
of the array and the number of elements allocated for the array and
reallocating memory if needed.
Acked-by: Benjamin Gaignard <benjamin.gaignard@collabora.com> Acked-by: Nicolas Dufresne <nicolas.dufresne@collabora.com> Tested-by: Benjamin Gaignard <benjamin.gaignard@collabora.com> Tested-by: Jernej Skrabec <jernej.skrabec@gmail.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Add a new flag that indicates that this control is a dynamically sized
array. Also document this flag.
Currently dynamically sized arrays are limited to one dimensional arrays,
but that might change in the future if there is a need for it.
The initial use-case of dynamic arrays are stateless codecs. A frame
can be divided in many slices, so you want to provide an array containing
slice information for each slice. Typically the number of slices is small,
but the standard allow for hundreds or thousands of slices. Dynamic arrays
are a good solution since sizing the array for the worst case would waste
substantial amounts of memory.
Acked-by: Nicolas Dufresne <nicolas.dufresne@collabora.com> Tested-by: Benjamin Gaignard <benjamin.gaignard@collabora.com> Tested-by: Jernej Skrabec <jernej.skrabec@gmail.com> Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Georgi Djakov [Fri, 15 Jul 2022 14:56:31 +0000 (17:56 +0300)]
Merge branch 'icc-rpm' into icc-next
This patch set is to support bucket in icc-rpm driver, so it implements
the similar mechanism in the icc-rpmh driver.
It uses interconnect path tag to indicate the bandwidth voting is for
which buckets, and there have three kinds of buckets: AWC, WAKE and
SLEEP, finally the wake and sleep bucket values are used to set the
corresponding clock (active and sleep clocks). So far, we keep the AWC
bucket but doesn't really use it.
Georgi Djakov [Fri, 15 Jul 2022 14:55:48 +0000 (17:55 +0300)]
Merge branch 'icc-imx8mp' into icc-next
This patchset is to support i.MX8MP NoC settings, i.MX8MP NoC initial
value after power up is invalid, need set a valid value after related
power domain up.
This patchset also includes two patch[1,2] during my development to enable
the ICC feature for i.MX8MP.
I not include ddrc DVFS in this patchset, ths patchset is only to
support NoC value mode/priority/ext_control being set to a valid value
that suggested by i.MX Chip Design Team. The value is same as NXP
downstream one inside Arm Trusted Firmware:
https://source.codeaurora.org/external/imx/imx-atf/tree/plat/imx/imx8m/i/gpc.c?h=lf_v2.4#n97
Introduce imx_icc_noc_setting structure to describe a master port setting
Pass imx_icc_noc_setting as a parameter from specific driver
Set priority level, mode, ext control in imx_icc_node_set
Peng Fan [Sun, 3 Jul 2022 09:11:26 +0000 (17:11 +0800)]
interconnect: imx: fix max_node_id
max_node_id not equal to the ARRAY_SIZE of node array, need increase 1,
otherwise xlate will fail for the last entry. And rename max_node_id
to num_nodes to reflect the reality.
media: venus: set ubwc configuration on specific video hardware
UBWC configuration parameters would vary across video hardware
generations. At the same time, driver is expected to configure these
parameters, without relying on video firmware to use the default
configurations.
Setting the configuration parameters for sc7280.
Hans Verkuil [Tue, 12 Jul 2022 10:47:15 +0000 (11:47 +0100)]
media: venus: venus_helper_get_bufreq(): req is never NULL
Fix a smatch error:
drivers/media/platform/qcom/venus/helpers.c: drivers/media/platform/qcom/venus/helpers.c:678 venus_helper_get_bufreq() error: we previously assumed 'req' could be null (see line 674)
After checking how venus_helper_get_bufreq() is called it is clear that
req is never NULL, so just drop the checks.
media: ov5693: add support for acpi clock-frequency prop
Add support for ACPI-based platforms that specify the clock frequency by
using the "clock-frequency" property instead of specifying a clock
provider reference
Daniel Scally [Thu, 7 Jul 2022 22:47:33 +0000 (23:47 +0100)]
media: entity: Use dedicated data link iterator
Where iteration over links for an entity is clearly assuming that
all of those links are data links, use the new iterator to guarantee
that assumption is met.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Daniel Scally <djrscally@gmail.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
ALSA: hda: Skip event processing for unregistered codecs
When codec is unbound but not yet removed, in the eyes of
snd_hdac_bus_process_unsol_events() it is still a valid target to
delegate work to. Such behaviour may lead to use-after-free errors.
Address by verifying if codec is actually registered.
Daniel Scally [Thu, 7 Jul 2022 22:47:32 +0000 (23:47 +0100)]
media: entity: Add iterator for entity data links
Iterating over the links for an entity is a somewhat common need
through the media subsystem, but generally the assumption is that
they will all be data links. To meet that assumption add a new macro
that iterates through an entity's links and skips non-data links.
Signed-off-by: Daniel Scally <djrscally@gmail.com> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Stefan Binding [Thu, 30 Jun 2022 00:23:35 +0000 (01:23 +0100)]
ALSA: hda: cs35l41: Add module parameter to control firmware load
By default, the driver will automatically load DSP firmware
for the amps, if available. Adding this option allows the
autoload to be optional, which allows for different configurations.
Stefan Binding [Thu, 30 Jun 2022 00:23:34 +0000 (01:23 +0100)]
ALSA: hda: cs35l41: Support Firmware switching and reloading
This is required to support CS35L41 calibration.
By default, speaker protection firmware will be loaded, if
available. However, different firmware is required to run
the calibration sequence, so it is necessary to add support
to be able to unload, switch and reload firmware.
This patch adds 2 ALSA Controls for each amp:
"DSP1 Firmware Load"
"DSP1 Firmware Type"
"DSP1 Firmware Load" can be used to unload and
load the firmware.
"DSP1 Firmware Type" can be used to switch the
target firmware to be loaded by "DSP1 Firmware Load"
Since loading firmware can add new ALSA controls, it is
necessary to ensure the firmware loading is run asynchronously
from the ALSA control itself to prevent deadlocks.
Note: When switching between firmwares, an ALSA control is
only added if it has not previously existed. If it had existed
previously, it will be re-enabled instead.
The config sequences for running with and without firmware and DSP
are different. The original behavior assumed that we would only
run without DSP only in the case where firmware load failed.
This meant the non-firmware sequence was written with the assumtion
that various registers would be set to their default value.
However, to support the ability to unload the firmware, the
non-firmware register sequence must be updated to update all
required registers, including values that would be defaulted,
in case the firmware sequence, which could have already run,
has changed their value.
Tomi Valkeinen [Fri, 1 Jul 2022 13:15:59 +0000 (14:15 +0100)]
media: stm32: dcmi: Fix subdev op call with uninitialized state
stm32-dcmi calls its source subdev with v4l2_subdev_call() using a
v4l2_subdev_state constructed on stack. This means that init_cfg is
never called for that state, and a source subdev that depends on the
init_cfg call may break.
A new macro has been added for this particular purpose, which properly
initializes the state, so let's use v4l2_subdev_call_state_try() here.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com> Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Tested-by: Marek Vasut <marex@denx.de> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Stefan Binding [Thu, 30 Jun 2022 00:23:30 +0000 (01:23 +0100)]
ALSA: hda: cs35l41: Support Hibernation during Suspend
CS35L41 supports hibernation during suspend when using
DSP firmware.
When the driver suspends it will hibernate the part, if
firmware is running, and resume will wake from hibernation.
CS35L41 driver will suspend/resume when requested by
hda driver.
Note that suspend/resume and hibernation is only supported
when firmware is running.
Add a helper macro for the situations where a non-MC driver needs to
call a state-operation (operation which takes a subdev state as a
parameter) in try-context in another subdev.
The macro allocates a new subdev state for the called subdev and frees
the state afterwards.
An example use case is a media platform driver testing if a
v4l2_subdev_format would be accepted by a source subdev.
This should not be used in MC drivers.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com> Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Tested-by: Marek Vasut <marex@denx.de> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Laurent Pinchart [Sat, 18 Jun 2022 18:54:19 +0000 (19:54 +0100)]
media: Replace dependency on VIDEO_V4L2_SUBDEV_API with select
The VIDEO_V4L2_SUBDEV_API Kconfig symbol is mostly selected
automatically, with a a handful of drivers still using it as a
dependency. Fix them to use selection, and drop the symbol title text to
not expose it for manual selection.
Sakari Ailus [Wed, 13 Jul 2022 15:18:08 +0000 (16:18 +0100)]
media: sunxi: Depend on GENERIC_PHY_MIPI_DPHY
The sun6i-mipi-csi2 and sun6i-a83t-mipi-csi2 drivers depend on the generic
MIPI D-PHY support. Select it. This fixes a linking problem when either of
these drivers is enabled and GENERIC_PHY_MIPI_DPHY is disabled.
Merge tag 'asoc-v5.20' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-next
ASoC: Updates for v5.20
This is a big release thus far and there will probably be more changes
to come, it's a combination of a larger than usual crop of new drivers
and some subsysetm wide cleanups from Charles rather than anything
structural. The SOF and Intel DSP code both also continue to be very
actively developed.
- Restructing of the set_fmt() callbacks to be specified in terms of
the device rather than with semantics depending on if the device is
supposed to be a CODEC or SoC, making things clearer in situations
like CODEC to CODEC links.
- Clean up of the way we flag which DAI naming scheme we use to reflect
the progress that's been made modernising things.
- Merge of more of the Intel AVS driver stack, including some board
integrations.
- New version 4 mechanism for communication with SOF DSPs.
- Suppoort for dynamically selecting the PLL to use at runtime on i.MX
platforms.
- Improvements for CODEC to CODEC support in the generic cards.
- Support for AMD Jadeite and various machines, Intel MetorLake DSPs,
Mediatek MT8186 DSPs and MT6366, nVidia Tegra MDDRC, OPE and PEQ, NXP
TFA9890, Qualcomm SDM845, WCD9335 and WAS883x, and Texas Instruments
TAS2780.
drm/scheduler: Don't kill jobs in interrupt context
Interrupt context can't sleep. Drivers like Panfrost and MSM are taking
mutex when job is released, and thus, that code can sleep. This results
into "BUG: scheduling while atomic" if locks are contented while job is
freed. There is no good reason for releasing scheduler's jobs in IRQ
context, hence use normal context to fix the trouble.
Stylon Wang [Thu, 7 Jul 2022 08:23:29 +0000 (16:23 +0800)]
drm/amd/display: Fix new dmub notification enabling in DM
[Why]
Changes from "Fix for dmub outbox notification enable" need to land
in DM or DMUB outbox notification would be disabled.
[How]
Enable outbox notification only after interrupt are enabled and IRQ
handlers registered. Any pending notification will be sent by DMUB
once outbox notification is enabled.
Fixes: ed7208706448 ("drm/amd/display: Fix for dmub outbox notification enable") Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com> Acked-by: Solomon Chiu <solomon.chiu@amd.com> Signed-off-by: Stylon Wang <stylon.wang@amd.com> Acked-by: Harry Wentland <harry.wentland@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org
Laurent Pinchart [Thu, 17 Mar 2022 12:37:12 +0000 (12:37 +0000)]
media: v4l2: Make colorspace validity checks more future-proof
The helper functions that test validity of colorspace-related fields
use the last value of the corresponding enums. This isn't very
future-proof, as there's a high chance someone adding a new value may
forget to update the helpers. Add new "LAST" entries to the enumerations
to improve this, and keep them private to the kernel.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com> Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
media: mediatek: vcodec: Make encoder capability fields fit requirements
This partially reverts commit fd9f8050e355d7fd1e126cd207b06c96cde7f783,
and changes things so that the capability string fields of the encoder
conform to their requirements.
The driver name field should contain the actual driver name, not some
otherwise unused string macro from the driver. To make this clear,
copy the name from the driver's name field.
The card name for the video encoder previously held a static platform
name that was fixed to match MT8173. This obviously doesn't make sense
for newer chips. Since commit fd9f8050e355 ("media: mediatek: vcodec:
Change encoder v4l2 capability value"), this field was changed to hold
the driver's name, or "mtk-vcodec-dec". This doesn't make much sense
either, since this still doesn't reflect what chip this is.
Instead, fill in the card name with "MTxxxx video encoder" with the
proper chip number.
Since commit f2d8b6917f3b ("media: v4l: ioctl: Set bus_info in
v4l_querycap()"), the V4L2 core provides a default value for the
bus_info field for platform and PCI devices. This value will match
the default value for media devices added by commit cef699749f37
("media: mc: Set bus_info in media_device_init()"). These defaults
are stable and device-specific.
Drop the custom capability bus_info from the mtk-vcodec encoder
driver, and use the defaults.
As this patch removes the last usage of MTK_VCODEC_DRV_NAME, remove
the macro as well.
media: mediatek: vcodec: Make decoder capability fields fit requirements
This partially reverts commit a8a7a278c56ad3b4ddd4db9a960e0537d032b0b3,
and changes things so that the capability string fields of the decoder
conform to their requirements.
This recent change caused ChromeOS's decoder to no longer function. This
is due to ChromeOS using the driver name field to match the video device
with its accompanying media device. After the change, they no longer
matched.
The driver name field should contain the actual driver name, not some
otherwise unused string macro from the driver. To make this clear,
copy the name from the driver's name field.
The card name for the video decoder previously held a static platform
name that was fixed to match MT8173. This obviously doesn't make sense
for newer chips. Since commit a8a7a278c56a ("media: mediatek: vcodec:
Change decoder v4l2 capability value"), this field was changed to hold
the driver's name, or "mtk-vcodec-dec". This doesn't make much sense
either, since this still doesn't reflect what chip this is.
Instead, fill in the card name with "MTxxxx video decoder" with the
proper chip number.
Since commit f2d8b6917f3b ("media: v4l: ioctl: Set bus_info in
v4l_querycap()"), the V4L2 core provides a default value for the
bus_info field for platform and PCI devices. This value will match
the default value for media devices added by commit cef699749f37
("media: mc: Set bus_info in media_device_init()"). These defaults
are stable and device-specific.
Drop the custom capability bus_info from the mtk-vcodec decoder
driver, and use the defaults. This also fixes the long standing
issue where the media device used for the stateless decoder didn't
have its bus_info set, and would never match its accompanying video
device.
Marko Mäkelä [Fri, 8 Jul 2022 08:44:59 +0000 (09:44 +0100)]
media: lirc: ensure lirc device receives repeats
Pressing a button on a remote control unit will typically lead to
messages being sent several times per second until the button is released.
Some remote control units indicate long key presses by sending
special "repeat" messages, for which the protocol driver calls
rc_repeat(). Other units repeat the same message over and over,
which will be handled by calling rc_keydown().
The function rc_keydown() never set the LIRC "repeat" flag to distinguish
repeated messages that were sent due to a long keypress, and messages
sent due to repeated short keypresses. While a user-space program may
implement special logic to distinguish long keypresses, it is much simpler
to be able to rely on the flag.
Signed-off-by: Marko Mäkelä <marko.makela@iki.fi> Co-developed-by: Sean Young <sean@mess.org> Signed-off-by: Sean Young <sean@mess.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Daniel Oakley [Thu, 16 Jun 2022 10:07:47 +0000 (11:07 +0100)]
media: vimc: use data link entities enum to index the ent_config array
Future additions to the ent_config[] could break the association between
the index of the struct vimc_ent_config entries in the ent_config[] array,
and the index defined by the enum proposed in the previous patch. Using
designated initializers solves this by linking the 2 together clearly in
code and prevents the array not reflecting the enum. There is no
functional change intended.
Daniel Oakley [Thu, 16 Jun 2022 10:07:46 +0000 (11:07 +0100)]
media: vimc: enumerate data link entities for clarity
The data_links array was hard to read and understand. By implementing
enumerated vimc data link entities, clarity has been improved when
defining data_links. This therefore should help new programmers to
understand the codebase better. There is no functional change intended.
projects / people / ms / linux.git / log
