Keith Busch [Tue, 12 Jul 2022 15:16:32 +0000 (08:16 -0700)]
nvme-pci: fix freeze accounting for error handling
A reset on a live device experiencing a link error still needs to have
the queue freeze state started for the subsequent reinitialization. Skip
only the register read if the device is not present instead of bypassing
the freeze checks.
Fixes: b98235d3a471e ("nvme-pci: harden drive presence detect in nvme_dev_disable()") Reported-by: Niklas Schnelle <schnelle@linux.ibm.com> Signed-off-by: Keith Busch <kbusch@kernel.org> Tested-by: Niklas Schnelle <schnelle@linux.ibm.com> Signed-off-by: Christoph Hellwig <hch@lst.de>
serial: 8250: lpc18xx: Remove redundant sanity check for RS485 flags
Before the drivers rs485_config() function is called the serial core
already ensures that only one of both options RTS on send or RTS after send
is set. So remove the concerning sanity check in the driver function to
avoid redundancy.
serial: 8250_dwlib: remove redundant sanity check for RS485 flags
Before the drivers rs485_config() function is called the serial core
already ensures that only one of both options RTS on send or RTS after send
is set. So remove the concerning sanity check in the driver function to
avoid redundancy.
Currently the documentation claims that a maximum of 1000 msecs is allowed
for RTS delays. However nothing actually checks the values read from device
tree/ACPI and so it is possible to set much higher values.
There is already a maximum of 100 ms enforced for RTS delays that are set
via the UART TIOCSRS485 ioctl. To be consistent with that use the same
limit for DT/ACPI values.
Although this change is visible to userspace the risk of breaking anything
when reducing the max delays from 1000 to 100 ms should be very low, since
100 ms is already a very high maximum for delays that are usually rather in
the usecs range.
serial: core: sanitize RS485 delays read from device tree
Currently the RTS delays set via device tree are not clamped to a maximum
value although the device tree bindings documentation for RS485 claims that
only a maximum of 1000 msecs is allowed.
So clamp the values to avoid arbitrary high delay settings. However clamp
the values to 100 instead of 1000 msecs to be consistent which the maximum
that is allowed when setting the delays from userspace via the UART ioctl
TIOCSRS485.
serial: core, 8250: set RS485 termination GPIO in serial core
In serial8250_em485_config() the termination GPIO is set with the uart_port
spinlock held. This is an issue if setting the GPIO line can sleep (e.g.
since the concerning GPIO expander is connected via SPI or I2C).
Fix this by setting the termination line outside of the uart_port spinlock
in the serial core and using gpiod_set_value_cansleep() which instead of
gpiod_set_value() allows it to sleep.
Beside fixing the termination GPIO line setting for the 8250 driver this
change also makes setting the termination GPIO generic for all UART
drivers.
serial: ar933x: Remove superfluous code in ar933x_config_rs485()
In ar933x_config_rs485() the check for the RTS GPIO is not needed since in
case the GPIO is not available at driver init ar933x_no_rs485 is assigned
to port->rs485_supported and this function is never called. So remove the
check.
Also in uart_set_rs485_config() the serial core already assigns the passed
serial_rs485 struct to the uart port. So remove the assignment in the
drivers rs485_config() function to avoid redundancy.
RS485 is not possible without an RTS GPIO regardless of whether RS485 is
enabled at boot time or not. So correct the concerning check in the probe()
function.
serial: 8250_bcm7271: Save/restore RTS in suspend/resume
Commit 9cabe26e65a8 ("serial: 8250_bcm7271: UART errors after resuming
from S2") prevented an early enabling of RTS during resume, but it did
not actively restore the RTS state after resume.
serial: 8250_dw: Avoid pslverr on reading empty receiver fifo
With PSLVERR_RESP_EN parameter set to 1, the device generates an error
response when an attempt to read an empty RBR with FIFO enabled.
This happens when LCR writes are ignored when UART is busy.
dw8250_check_lcr() in retries to update LCR, invokes dw8250_force_idle()
to clear and reset FIFO and eventually reads UART_RX causing the error.
Avoid this by not reading RBR/UART_RX when no data is available.
serial: 8250: SERIAL_8250_ASPEED_VUART should depend on ARCH_ASPEED
The Aspeed Virtual UART is only present on Aspeed BMC platforms. Hence
add a dependency on ARCH_ASPEED, to prevent asking the user about this
driver when configuring a kernel without Aspeed BMC support.
Cameron Williams [Mon, 11 Jul 2022 15:35:10 +0000 (16:35 +0100)]
tty: 8250: Add support for Brainboxes PX cards.
Add support for some of the Brainboxes PCIe (PX) range of
serial cards, including the PX-101, PX-235/PX-246,
PX-203/PX-257, PX-260/PX-701, PX-310, PX-313,
PX-320/PX-324/PX-376/PX-387, PX-335/PX-346, PX-368, PX-420,
PX-803 and PX-846.
Similar to mux and orientation switch, add a handle for registered
retimer to the port, so that it has handles to the various switches
connected to it.
Introduce a retimer device class and associated functions that register
and use retimer "switch" devices. These operate in a manner similar to
the "mode-switch" and help configure retimers that exist between the
Type-C connector and host controller(s).
Type C ports can be linked to retimers using firmware node device
references (again, in a manner similar to "mode-switch").
There are no new sysfs files being created; there is the new retimer
class directory, but there are no class-specific files being created
there.
Not all platforms have all of the four currently supported wakeup
interrupts so use the optional irq helpers when looking up interrupts to
avoid printing error messages when an optional interrupt is not found:
dwc3-qcom a6f8800.usb: error -ENXIO: IRQ hs_phy_irq not found
Johan Hovold [Wed, 13 Jul 2022 13:13:34 +0000 (15:13 +0200)]
dt-bindings: usb: qcom,dwc3: add SC8280XP binding
Add SC8280XP to the DT schema.
Note that the SC8280XP controllers use the common set of five clocks and
an additional set of four interconnect clocks whose purpose is not
entirely clear at this point.
The set of wakeup interrupts is also different for SC8280XP.
usb: dwc3: core: Do not perform GCTL_CORE_SOFTRESET during bootup
According to the programming guide, it is recommended to
perform a GCTL_CORE_SOFTRESET only when switching the mode
from device to host or host to device. However, it is found
that during bootup when __dwc3_set_mode() is called for the
first time, GCTL_CORESOFTRESET is done with suspendable bit(BIT 17)
of DWC3_GUSB3PIPECTL set. This some times leads to issues
like controller going into bad state and controller registers
reading value zero. Until GCTL_CORESOFTRESET is done and
run/stop bit is set core initialization is not complete.
Setting suspendable bit of DWC3_GUSB3PIPECTL and then
performing GCTL_CORESOFTRESET is therefore not recommended.
Avoid this by only performing the reset if current_dr_role is set,
that is, when doing subsequent role switching.
Liang He [Wed, 13 Jul 2022 12:05:28 +0000 (20:05 +0800)]
usb: aspeed-vhub: Fix refcount leak bug in ast_vhub_init_desc()
We should call of_node_put() for the reference returned by
of_get_child_by_name() which has increased the refcount.
Fixes: 30d2617fd7ed ("usb: gadget: aspeed: allow to set usb strings in device tree") Signed-off-by: Liang He <windhl@126.com> Link: https://lore.kernel.org/r/20220713120528.368168-1-windhl@126.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jiangshan Yi [Wed, 13 Jul 2022 07:02:05 +0000 (15:02 +0800)]
usb: ldusb: replace ternary operator with max_t()
Fix the following coccicheck warning:
drivers/usb/misc/ldusb.c:719: WARNING opportunity for max().
drivers/usb/misc/ldusb.c:721: WARNING opportunity for max().
max_t() macro is defined in include/linux/minmax.h. It avoids
multiple evaluations of the arguments when non-constant and performs
strict type-checking.
usb: dwc3: ep0: Properly handle setup_packet_pending scenario in data stage
During a 3 stage SETUP transfer, if the host sends another SETUP token
before completing the status phase, it signifies that the host has aborted
the current control transfer. Currently, if a setup_packet_pending is
received, there are no subsequent calls to dwc3_ep0_out_start() to fetch
the new SETUP packet. This leads to a stall on EP0, as host does not
expect another STATUS phase as it has aborted the current transfer.
Fix this issue by explicitly stalling and restarting EP0, as well as
resetting the trb_enqueue indexes. (without this, there is a chance the
SETUP TRB is set up on trb_endqueue == 1)
When building with 'W=1' the compiler complains about missing
prototypes for onboard_hub_create/destroy_pdevs(). Include the
header with the prototypes to fix this.
Revert "dt-bindings: usb: mtk-xhci: Make all clocks required"
This reverts commit ebc4969ae125e65fdb563f66f4bfa7aec95f7eb4. That
commit was supposed to make the binding better reflect the MediaTek XHCI
hardware block by requiring all clocks to be present. But doing that
also causes too much noise in the devicetrees, since it requires
updating old MediaTek DTs to add clock handles for the fixed clocks, and
going forward every new clock added to the binding would require even
more updates.
The commit also didn't update the example to match the changes, causing
additional warnings.
Instead let's keep the clocks optional so that old devicetrees can keep
omitting the fixed clocks, and we'll just add the clocks as required on
new DTs.
Fixes: ebc4969ae125 ("dt-bindings: usb: mtk-xhci: Make all clocks required") Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Reviewed-by: Chunfeng Yun <chunfeng.yun@mediatek.com> Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com> Link: https://lore.kernel.org/r/20220708192605.43351-1-nfraprado@collabora.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It allows to reset prevent_medium_removal flag and "eject" the image.
This can be useful to free the drive from a hunging host or if the host
continues to use the drive even after unmounting (Linux does this).
It's also a bit like using an unfolded paperclip on an optical drive.
Previously, the undocumented method of sending SIGUSR1 to a special
"file-storage" kernel thread could be used for these purposes,
but when using multiple storages there was no way to distinguish
one from the other, so we had to send a signal to everyone.
Randy Dunlap [Sat, 9 Jul 2022 01:36:01 +0000 (18:36 -0700)]
usb: gadget: udc: amd5536 depends on HAS_DMA
USB_AMD5536UDC should depend on HAS_DMA since it selects USB_SNP_CORE,
which depends on HAS_DMA and since 'select' does not follow any
dependency chains.
Fixes this kconfig warning:
WARNING: unmet direct dependencies detected for USB_SNP_CORE
Depends on [n]: USB_SUPPORT [=y] && USB_GADGET [=y] && (USB_AMD5536UDC [=y] || USB_SNP_UDC_PLAT [=n]) && HAS_DMA [=n]
Selected by [y]:
- USB_AMD5536UDC [=y] && USB_SUPPORT [=y] && USB_GADGET [=y] && USB_PCI [=y]
Martin Kaiser [Wed, 13 Jul 2022 07:55:52 +0000 (09:55 +0200)]
staging: r8188eu: fall back to random mac address
Call eth_random_addr to generate a random mac address if we cannot load
the mac address from the efuses.
Do not use a constant mac address as fallback. This may create conflicts
if we have several r8188eu devices on the network.
Suggested-by: Joe Perches <joe@perches.com> Tested-by: Philipp Hortmann <philipp.g.hortmann@gmail.com> # Edimax N150 Reviewed-by: Pavel Skripkin <paskripkin@gmail.com> Signed-off-by: Martin Kaiser <martin@kaiser.cx> Link: https://lore.kernel.org/r/20220713075552.140927-1-martin@kaiser.cx Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Martin Kaiser [Wed, 13 Jul 2022 07:58:04 +0000 (09:58 +0200)]
staging: r888eu: use dynamic allocation for efuse buffer
Use kmalloc to allocate the efuse buffer in ReadAdapterInfo8188EU and
free it on exit. This is better than using a 512 byte array on the stack.
It's ok to drop the __aligned(4) qualifier. kmalloc aligns to
ARCH_KMALLOC_MINALIGN, this is at least 8 bytes.
Suggested-by: Dan Carpenter <dan.carpenter@oracle.com> Suggested-by: Larry Finger <Larry.Finger@lwfinger.net> Acked-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Martin Kaiser <martin@kaiser.cx> Link: https://lore.kernel.org/r/20220713075804.140986-1-martin@kaiser.cx Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ming Lei [Thu, 14 Jul 2022 10:32:01 +0000 (18:32 +0800)]
ublk_drv: fix request queue leak
Call blk_cleanup_queue() in release code path for fixing request
queue leak.
Also for-5.20/block has cleaned up blk_cleanup_queue(), which is
basically merged to del_gendisk() if blk_mq_alloc_disk() is used
for allocating disk and queue.
However, ublk may not add disk in case of starting device failure, then
del_gendisk() won't be called when removing ublk device, so blk_mq_exit_queue
will not be callsed, and it can be bit hard to deal with this kind of
merge conflict.
Turns out ublk's queue/disk use model is very similar with scsi, so switch
to scsi's model by allocating disk and queue independently, then it can be
quite easy to handle v5.20 merge conflict by replacing blk_cleanup_queue
with blk_mq_destroy_queue.
Reported-by: Jens Axboe <axboe@kernel.dk> Fixes: 71f28f3136af ("ublk_drv: add io_uring based userspace block driver") Signed-off-by: Ming Lei <ming.lei@redhat.com> Link: https://lore.kernel.org/r/20220714103201.131648-1-ming.lei@redhat.com Signed-off-by: Jens Axboe <axboe@kernel.dk>
Ming Lei [Wed, 13 Jul 2022 14:07:11 +0000 (22:07 +0800)]
ublk_drv: support to complete io command via task_work_add
Use task_work_add if it is available, since task_work_add can bring
up better performance, especially batching signaling ->ubq_daemon can
be done.
It is observed that task_work_add() can boost iops by +4% on random
4k io test. Also except for completing io command, all other code
paths are same with completing io command via
io_uring_cmd_complete_in_task.
Meantime add one flag of UBLK_F_URING_CMD_COMP_IN_TASK for comparing
the mode easily.
Ming Lei [Wed, 13 Jul 2022 14:07:10 +0000 (22:07 +0800)]
ublk_drv: add io_uring based userspace block driver
This is the driver part of userspace block driver(ublk driver), the other
part is userspace daemon part(ublksrv)[1].
The two parts communicate by io_uring's IORING_OP_URING_CMD with one
shared cmd buffer for storing io command, and the buffer is read only for
ublksrv, each io command is indexed by io request tag directly, and is
written by ublk driver.
For example, when one READ io request is submitted to ublk block driver,
ublk driver stores the io command into cmd buffer first, then completes
one IORING_OP_URING_CMD for notifying ublksrv, and the URING_CMD is issued
to ublk driver beforehand by ublksrv for getting notification of any new
io request, and each URING_CMD is associated with one io request by tag.
After ublksrv gets the io command, it translates and handles the ublk io
request, such as, for the ublk-loop target, ublksrv translates the request
into same request on another file or disk, like the kernel loop block
driver. In ublksrv's implementation, the io is still handled by io_uring,
and share same ring with IORING_OP_URING_CMD command. When the target io
request is done, the same IORING_OP_URING_CMD is issued to ublk driver for
both committing io request result and getting future notification of new
io request.
Another thing done by ublk driver is to copy data between kernel io
request and ublksrv's io buffer:
1) before ubsrv handles WRITE request, copy the request's data into
ublksrv's userspace io buffer, so that ublksrv can handle the write
request
2) after ubsrv handles READ request, copy ublksrv's userspace io buffer
into this READ request, then ublk driver can complete the READ request
Zero copy may be switched if mm is ready to support it.
ublk driver doesn't handle any logic of the specific user space driver,
so it is small/simple enough.
drm/mgag200: Don't read-back PCI option register before writing
Remove the read operation from mgag200_init_pci_options(). It was
incorrectly added while refactoring the code. Reading the PCI option
register clears the register's new value and subsequently leads to
re-writing the old value.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de> Reviewed-by: Jocelyn Falempe <jfalempe@redhat.com> Fixes: ce19021fd99a ("drm/mgag200: Move PCI-option setup into model-specific code") Cc: Thomas Zimmermann <tzimmermann@suse.de> Cc: Jocelyn Falempe <jfalempe@redhat.com> Cc: Dave Airlie <airlied@redhat.com> Cc: dri-devel@lists.freedesktop.org Link: https://patchwork.freedesktop.org/patch/msgid/20220708072114.13960-1-tzimmermann@suse.de
Merge tag 'iio-for-5.20a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into char-misc-next
Jonathan writes:
IIO new device support, features and minor fixes for 5.20
Several on-running cleanup efforts dominate this time, plus the DMA
safety alignment issue identified due to improved understanding of
the restrictions as a result of Catalin Marinas' efforts in that area.
One immutable branch in here due to MFD and SPMI elements needed for
the qcom-rradc driver.
Device support
* bmi088
- Add support for bmi085 (accelerometer part of IMU)
- Add support for bmi090l (accelerometer part of IMU)
* mcp4922
- Add support for single channel device MCP4921
* rzg2l-adc
- Add compatible and minor tweaks to support RZ/G2UL ADC
* sca3300
- Add support for scl3300 including refactoring driver to support
multiple device types and cleanup noticed whilst working on driver.
* spmi-rradc
- New driver for Qualcomm SPMI Round Robin ADC including necessary
additional utility functions in SPMI core and related MFD driver.
* ti-dac55781
- Add compatible for DAC121C081 which is very similar to existing parts.
Features
* core
- Warn on iio_trigger_get() on an unregistered IIO trigger.
* bma400
- Triggered buffer support
- Activity and step counting
- Misc driver improvements such as devm and header ordering
* cm32181
- Add PM support.
* cros_ec
- Sensor location support
* sx9324
- Add precharge resistor setting
- Add internal compensation resistor setting
- Add CS idle/sleep mode.
* sx9360
- Add precharge resistor setting
* vl53l0x
- Handle reset GPIO, regulator and relax handling of irq type.
Cleanup and minor fixes:
Treewide changes
- Cleanup of error handling in remove functions in many drivers.
- Update dt-binding maintainers for a number of ADI bindings.
- Several sets of conversion of drivers from device tree specific to
generic device properties. Includes fixing up various related
header and Kconfig issues.
- Drop include of of.h from iio.h and fix up drivers that need to include
it directly.
- More moves of clusters of drivers into appropriate IIO_XXX namespaces.
- Tree wide fix of a long running bug around DMA safety requirements.
IIO was using __cacheline_aligned to pad iio_priv() structures. This
worked for a long time by coincidence, but correct alignment is
ARCH_KMALLOC_MINALIGN. As there is activity around this area, introduce
an IIO local IIO_DMA_MINALIGN to allow for changing it in one place rather
than every driver in future. Note, there have been no reports of this
bug in the wild, and it may not happen on any platforms supported by
upstream, so no rush to backport these fixes.
Other cleanup
* core
- Switch to ida_alloc()/free()
- Drop unused iio_get_time_res()
- Octal permissions and DEVICE_ATTR_* macros.
- Cleanup bared unsigned usage.
* MAINTAINERS
- Add include/dt-bindings/iio/ to the main IIO entry.
* ad5380
- Comment syntax fix.
* ad74413r
- Call to for_each_set_bit_from(), with from value as 0 replaced.
* ad7768-1
- Drop explicit setting of INDIO_BUFFER_TRIGGERED as now done by the core.
* adxl345
- Fix wrong address in dt-binding example.
* adxl367
- Drop extra update of FIFO watermark.
* at91-sama5d2
- Limit requested watermark to the hwfifo size.
* bmg160, bme680
- Typos
* cio-dac
- Switch to iomap rather than direct use of ioports
* kxsd9
- Replace CONFIG_PM guards with new PM macros that let the compiler
cleanly remove the unused code and structures when !CONFIG_PM
* lsm6dsx
- Use new pm_sleep_ptr() and EXPORT_SIMPLE_DEV_PM_OPS(). Then move
to Namespace.
* meson_saradc - general cleanup.
- Avoid attaching resources to iio_dev->dev
- Use same struct device for all error messages
- Convert to dev_err_probe() and use local struct device *dev to
reduce code complexity.
- Use devm_clk_get_optional() instead of hand rolling.
- Use regmap_read_poll_timeout() instead of hand rolling.
* mma7660
- Drop ACPI_PTR() use that is unhelpful.
* mpu3050
- Stop exporting symbols not used outside of module
- Switch to new DEFINE_RUNTIME_DEV_PM_OPS() macro and move to Namespace.
* ping
- Typo fix
* qcom-spmi-rradc
- Typo fix
* sc27xx
- Convert to generic struct u32_fract
* srf08
- Drop a redundant check on !val
* st_lsm6dsx
- Limit the requested watermark to the hwfifo size.
* stm32-adc
- Use generic_handle_domain_irq() instead of opencoding.
- Fix handling of ADC disable.
* stm32-dac
- Use str_enabled_disable() instead of open coding.
* stx104
- Switch to iomap rather than direct use of ioports
* tsc2046
- Drop explicit setting of INDIO_BUFFER_TRIGGERED as now done by the core.
* tsl2563
- Replace flush_scheduled_work() with cancel_delayed_work_sync()
- Replace cancel_delayed_work() with cancel_delayed_work_sync()
* vl53l0x
- Make the VDD regulator optional by allowing a dummy regulator.
* tag 'iio-for-5.20a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (244 commits)
iio: adc: xilinx-xadc: Drop duplicate NULL check in xadc_parse_dt()
iio: adc: xilinx-xadc: Make use of device properties
iio: light: cm32181: Add PM support
iio: adc: ad778-1: do not explicity set INDIO_BUFFER_TRIGGERED mode
iio: adc: ti-tsc2046: do not explicity set INDIO_BUFFER_TRIGGERED mode
iio: adc: stm32-adc: disable adc before calibration
iio: adc: stm32-adc: make safe adc disable
iio: dac: ad5380: align '*' each line and drop unneeded blank line
iio: adc: qcom-spmi-rradc: Fix spelling mistake "coherrency" -> "coherency"
iio: Don't use bare "unsigned"
dt-bindings: iio: dac: mcp4922: expand for mcp4921 support
iio: dac: mcp4922: add support to mcp4921
iio: chemical: sps30: Move symbol exports into IIO_SPS30 namespace
iio: pressure: bmp280: Move symbol exports to IIO_BMP280 namespace
iio: imu: bmi160: Move exported symbols to IIO_BMI160 namespace
iio: adc: stm32-adc: Use generic_handle_domain_irq()
proximity: vl53l0x: Make VDD regulator actually optional
MAINTAINERS: add include/dt-bindings/iio to IIO SUBSYSTEM AND DRIVERS
dt-bindings: iio/accel: Fix adi,adxl345/6 example I2C address
iio: gyro: bmg160: Fix typo in comment
...
It turned out that this is not correct. Especially the sync_file info
IOCTL needs to see even signaled fences to correctly report back their
status to userspace.
Instead add the filter in the merge function again where it makes sense.
Nicolas Dichtel [Wed, 13 Jul 2022 11:48:53 +0000 (13:48 +0200)]
selftests/net: test nexthop without gw
This test implement the scenario described in the commit
"ip: fix dflt addr selection for connected nexthop".
The test configures a nexthop object with an output device only (no gateway
address) and a route that uses this nexthop. The goal is to check if the
kernel selects a valid source address.
Nicolas Dichtel [Wed, 13 Jul 2022 11:48:52 +0000 (13:48 +0200)]
ip: fix dflt addr selection for connected nexthop
When a nexthop is added, without a gw address, the default scope was set
to 'host'. Thus, when a source address is selected, 127.0.0.1 may be chosen
but rejected when the route is used.
When using a route without a nexthop id, the scope can be configured in the
route, thus the problem doesn't exist.
To explain more deeply: when a user creates a nexthop, it cannot specify
the scope. To create it, the function nh_create_ipv4() calls fib_check_nh()
with scope set to 0. fib_check_nh() calls fib_check_nh_nongw() wich was
setting scope to 'host'. Then, nh_create_ipv4() calls
fib_info_update_nhc_saddr() with scope set to 'host'. The src addr is
chosen before the route is inserted.
When a 'standard' route (ie without a reference to a nexthop) is added,
fib_create_info() calls fib_info_update_nhc_saddr() with the scope set by
the user. iproute2 set the scope to 'link' by default.
Here is a way to reproduce the problem:
ip netns add foo
ip -n foo link set lo up
ip netns add bar
ip -n bar link set lo up
sleep 1
ip -n foo link add name eth0 type dummy
ip -n foo link set eth0 up
ip -n foo address add 192.168.0.1/24 dev eth0
ip -n foo link add name veth0 type veth peer name veth1 netns bar
ip -n foo link set veth0 up
ip -n bar link set veth1 up
ip -n bar address add 192.168.1.1/32 dev veth1
ip -n bar route add default dev veth1
ip -n foo nexthop add id 1 dev veth0
ip -n foo route add 192.168.1.1 nhid 1
Try to get/use the route:
> $ ip -n foo route get 192.168.1.1
> RTNETLINK answers: Invalid argument
> $ ip netns exec foo ping -c1 192.168.1.1
> ping: connect: Invalid argument
Try without nexthop group (iproute2 sets scope to 'link' by dflt):
ip -n foo route del 192.168.1.1
ip -n foo route add 192.168.1.1 dev veth0
Try to get/use the route:
> $ ip -n foo route get 192.168.1.1
> 192.168.1.1 dev veth0 src 192.168.0.1 uid 0
> cache
> $ ip netns exec foo ping -c1 192.168.1.1
> PING 192.168.1.1 (192.168.1.1) 56(84) bytes of data.
> 64 bytes from 192.168.1.1: icmp_seq=1 ttl=64 time=0.039 ms
>
> --- 192.168.1.1 ping statistics ---
> 1 packets transmitted, 1 received, 0% packet loss, time 0ms
> rtt min/avg/max/mdev = 0.039/0.039/0.039/0.000 ms
CC: stable@vger.kernel.org Fixes: 597cfe4fc339 ("nexthop: Add support for IPv4 nexthops") Reported-by: Edwin Brossette <edwin.brossette@6wind.com> Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Link: https://lore.kernel.org/r/20220713114853.29406-1-nicolas.dichtel@6wind.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>
ASoC: rsnd: care default case on rsnd_ssiu_busif_err_irq_ctrl()
Before, ssiu.c didn't care SSI5-8, thus,
commit b1384d4c95088d0 ("ASoC: rsnd: care default case on
rsnd_ssiu_busif_err_status_clear()") cares it for status clear.
But we should care it for error irq handling, too.
This patch cares it.
Reported-by: Nguyen Bao Nguyen <nguyen.nguyen.yj@renesas.com> Reported-by: Nishiyama Kunihiko <kunihiko.nishiyama.dn@renesas.com> Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Link: https://lore.kernel.org/r/871quocio1.wl-kuninori.morimoto.gx@renesas.com Signed-off-by: Mark Brown <broonie@kernel.org>
The value of "*ppos" was supposed to be zero but it is
sizeof(ipc4_msg->header_u64) so it will copy the data into the middle of
the "ipc4_msg->data_ptr" buffer instead of to the start. The second
problem is "buffer" should be "buffer + sizeof(ipc4_msg->header_u64)".
This function is used for fuzz testing so the data is normally random
and this bug likely does not affect anyone very much.
In this context, it's simpler and more appropriate to use copy_from_user()
instead of simple_write_to_buffer() so I have re-written the function.
Fixes: 066c67624d8c ("ASoC: SOF: ipc-msg-injector: Add support for IPC4 messages") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Link: https://lore.kernel.org/r/Ysg1tB2FKLnRMsel@kili Signed-off-by: Mark Brown <broonie@kernel.org>
Vaishnav Achath [Wed, 1 Jun 2022 07:16:11 +0000 (12:46 +0530)]
spi: cadence-quadspi: Remove spi_master_put() in probe failure path
Currently the spi_master is allocated by devm_spi_alloc_master()
and devres core manages the deallocation, but in probe failure
path spi_master_put() is being handled manually which causes
"refcount underflow use-after-free" warning when probe failure happens
after allocating spi_master.
Mark Brown [Wed, 13 Jul 2022 13:04:51 +0000 (14:04 +0100)]
ASoC: rockchip-i2s: Undo BCLK pinctrl changes
The version of the BCLK pinctrl management changes that made it into
v5.19 has caused problems on some systems due to overly strict DT
requirements but attempts to fix it have caused further breakage on
other platforms. Just drop the changes for this release, we already
have a better version queued for -next.
Fixes: 26b9f2fa7b1c ("ASoC: rockchip: i2s: Fix NULL pointer dereference when pinctrl is not found") Fixes: a5450aba737d ("ASoC: rockchip: i2s: switch BCLK to GPIO") Signed-off-by: Mark Brown <broonie@kernel.org> Link: https://lore.kernel.org/r/20220713130451.31481-1-broonie@kernel.org Signed-off-by: Mark Brown <broonie@kernel.org>
Ard Biesheuvel [Tue, 31 May 2022 08:49:24 +0000 (09:49 +0100)]
ARM: 9208/1: entry: add .ltorg directive to keep literals in range
LKP reports a build issue on Clang, related to a literal load of
__current issued through the ldr_va macro. This turns out to be due to
the fact that group relocations are disabled when CONFIG_COMPILE_TEST=y,
which means that the ldr_va macro resolves to a pair of LDR
instructions, the first one being a literal load issued too far from its
literal pool.
Due to the introduction of a couple of new uses of this macro in commit 508074607c7b95b2 ("ARM: 9195/1: entry: avoid explicit literal loads"),
the literal pools end up getting rearranged in a way that causes the
literal for __current to go out of range. Let's fix this up by putting a
.ltorg directive in a suitable place in the code.
Link: https://lore.kernel.org/all/202205290805.1vZLAr36-lkp@intel.com/ Fixes: 508074607c7b95b2 ("ARM: 9195/1: entry: avoid explicit literal loads") Reported-by: kernel test robot <lkp@intel.com> Signed-off-by: Ard Biesheuvel <ardb@kernel.org> Tested-by: Nathan Chancellor <nathan@kernel.org> Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Wang Kefeng [Tue, 24 May 2022 08:03:46 +0000 (09:03 +0100)]
ARM: 9207/1: amba: fix refcount underflow if amba_device_add() fails
"ARM: 9192/1: amba: fix memory leak in amba_device_try_add()" leads
to a refcount underflow if amba_device_add() fails, which called by
of_amba_device_create(), the of_amba_device_create() already exists
the error handling, so amba_put_device() only need to be added into
amba_deferred_retry().
Fixes: 7719a68b2fa4 ("ARM: 9192/1: amba: fix memory leak in amba_device_try_add()") Reported-by: Guenter Roeck <linux@roeck-us.net> Tested-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com> Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Paolo Bonzini [Thu, 14 Jul 2022 11:29:57 +0000 (07:29 -0400)]
Documentation: kvm: clarify histogram units
In the case of histogram statistics, the values are always sample
counts; the unit instead applies to the bucket range. For example,
halt_poll_success_hist is a nanosecond statistic because the buckets are
for 0ns, 1ns, 2-3ns, 4-7ns etc. There isn't really any other sensible
interpretation, but clarify this anyway in the Documentation.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Paolo Bonzini [Thu, 14 Jul 2022 11:27:31 +0000 (07:27 -0400)]
kvm: stats: tell userspace which values are boolean
Some of the statistics values exported by KVM are always only 0 or 1.
It can be useful to export this fact to userspace so that it can track
them specially (for example by polling the value every now and then to
compute a % of time spent in a specific state).
Therefore, add "boolean value" as a new "unit". While it is not exactly
a unit, it walks and quacks like one. In particular, using the type
would be wrong because boolean values could be instantaneous or peak
values (e.g. "is the rmap allocated?") or even two-bucket histograms
(e.g. "number of posted vs. non-posted interrupt injections").
Suggested-by: Amneesh Singh <natto@weirdnatto.in> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
x86/kvm: fix FASTOP_SIZE when return thunks are enabled
The return thunk call makes the fastop functions larger, just like IBT
does. Consider a 16-byte FASTOP_SIZE when CONFIG_RETHUNK is enabled.
Otherwise, functions will be incorrectly aligned and when computing their
position for differently sized operators, they will executed in the middle
or end of a function, which may as well be an int3, leading to a crash
like:
Fixes: aa3d480315ba ("x86: Use return-thunk in asm code") Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com> Co-developed-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Borislav Petkov <bp@suse.de> Cc: Josh Poimboeuf <jpoimboe@kernel.org> Cc: Paolo Bonzini <pbonzini@redhat.com> Reported-by: Linux Kernel Functional Testing <lkft@linaro.org>
Message-Id: <20220713171241.184026-1-cascardo@canonical.com> Tested-by: Jack Wang <jinpu.wang@ionos.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
KVM: nVMX: Always enable TSC scaling for L2 when it was enabled for L1
Windows 10/11 guests with Hyper-V role (WSL2) enabled are observed to
hang upon boot or shortly after when a non-default TSC frequency was
set for L1. The issue is observed on a host where TSC scaling is
supported. The problem appears to be that Windows doesn't use TSC
frequency for its guests even when the feature is advertised and KVM
filters SECONDARY_EXEC_TSC_SCALING out when creating L2 controls from
L1's. This leads to L2 running with the default frequency (matching
host's) while L1 is running with an altered one.
Keep SECONDARY_EXEC_TSC_SCALING in secondary exec controls for L2 when
it was set for L1. TSC_MULTIPLIER is already correctly computed and
written by prepare_vmcs02().
aq_nic_deinit() has been called while suspending, so we don't have to call
it again on resume.
Actually, call it again leads to another hang issue when resuming from
S3.
net: atlantic: remove deep parameter on suspend/resume functions
Below commit claims that atlantic NIC requires to reset the device on pm
op, and had set the deep to true for all suspend/resume functions.
commit 1809c30b6e5a ("net: atlantic: always deep reset on pm op, fixing up my null deref regression")
So, we could remove deep parameter on suspend/resume functions without
any functional change.
When creating VFs a kernel panic can happen when calling to
efx_ef10_try_update_nic_stats_vf.
When releasing a DMA coherent buffer, sometimes, I don't know in what
specific circumstances, it has to unmap memory with vunmap. It is
disallowed to do that in IRQ context or with BH disabled. Otherwise, we
hit this line in vunmap, causing the crash:
BUG_ON(in_interrupt());
This patch reenables BH to release the buffer.
Log messages when the bug is hit:
kernel BUG at mm/vmalloc.c:2727!
invalid opcode: 0000 [#1] PREEMPT SMP NOPTI
CPU: 6 PID: 1462 Comm: NetworkManager Kdump: loaded Tainted: G I --------- --- 5.14.0-119.el9.x86_64 #1
Hardware name: Dell Inc. PowerEdge R740/06WXJT, BIOS 2.8.2 08/27/2020
RIP: 0010:vunmap+0x2e/0x30
...skip...
Call Trace:
__iommu_dma_free+0x96/0x100
efx_nic_free_buffer+0x2b/0x40 [sfc]
efx_ef10_try_update_nic_stats_vf+0x14a/0x1c0 [sfc]
efx_ef10_update_stats_vf+0x18/0x40 [sfc]
efx_start_all+0x15e/0x1d0 [sfc]
efx_net_open+0x5a/0xe0 [sfc]
__dev_open+0xe7/0x1a0
__dev_change_flags+0x1d7/0x240
dev_change_flags+0x21/0x60
...skip...
Fixes: d778819609a2 ("sfc: DMA the VF stats only when requested") Reported-by: Ma Yuying <yuma@redhat.com> Signed-off-by: Íñigo Huguet <ihuguet@redhat.com> Acked-by: Edward Cree <ecree.xilinx@gmail.com> Link: https://lore.kernel.org/r/20220713092116.21238-1-ihuguet@redhat.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Jan Beulich [Wed, 13 Jul 2022 09:19:55 +0000 (11:19 +0200)]
xen-netfront: re-order error checks in xennet_get_responses()
Check the retrieved grant reference first; there's no point trying to
have xennet_move_rx_slot() move invalid data (and further defer
recognition of the issue, likely making diagnosis yet more difficult).
Signed-off-by: Jan Beulich <jbeulich@suse.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Jan Beulich [Wed, 13 Jul 2022 09:19:33 +0000 (11:19 +0200)]
xen-netfront: remove leftover call to xennet_tx_buf_gc()
In talk_to_netback(), called earlier from xennet_connect(), queues and
shared rings were just re-initialized, so all this function call could
result in is setting ->broken (again) right away in case any unconsumed
responses were found.
Signed-off-by: Jan Beulich <jbeulich@suse.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Jiangshan Yi [Thu, 14 Jul 2022 06:33:18 +0000 (14:33 +0800)]
fs/ext2: replace ternary operator with min_t()
Fix the following coccicheck warning:
fs/ext2/super.c:1494: WARNING opportunity for min().
fs/ext2/super.c:1533: WARNING opportunity for min().
min_t() macro is defined in include/linux/minmax.h. It avoids
multiple evaluations of the arguments when non-constant and performs
strict type-checking.
Henning Schild [Mon, 6 Jun 2022 16:41:38 +0000 (19:41 +0300)]
leds: simatic-ipc-leds-gpio: Add GPIO version of Siemens driver
On Apollo Lake the pinctrl drivers will now come up without ACPI. Use
that instead of open coding it.
Create a new driver for that which can later be filled with more GPIO
based models, and which has different dependencies.
Signed-off-by: Henning Schild <henning.schild@siemens.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Lee Jones <lee@kernel.org>
Henning Schild [Mon, 6 Jun 2022 16:41:37 +0000 (19:41 +0300)]
platform/x86: simatic-ipc: drop custom P2SB bar code
The two drivers that used to use this have been switched over to the
common P2SB accessor, so this code is not needed any longer.
Signed-off-by: Henning Schild <henning.schild@siemens.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Lee Jones <lee@kernel.org>
Henning Schild [Mon, 6 Jun 2022 16:41:36 +0000 (19:41 +0300)]
leds: simatic-ipc-leds: Convert to use P2SB accessor
Since we have a common P2SB accessor in tree we may use it instead of
open coded variants.
Replace custom code by p2sb_bar() call.
Signed-off-by: Henning Schild <henning.schild@siemens.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Lee Jones <lee@kernel.org>
Andy Shevchenko [Mon, 6 Jun 2022 16:41:34 +0000 (19:41 +0300)]
EDAC, pnd2: convert to use common P2SB accessor
Since we have a common P2SB accessor in tree we may use it instead of
open coded variants.
Replace custom code by p2sb_bar() call.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Tested-by: Henning Schild <henning.schild@siemens.com> Reviewed-by: Tony Luck <tony.luck@intel.com> Signed-off-by: Lee Jones <lee@kernel.org>
Andy Shevchenko [Mon, 6 Jun 2022 16:41:33 +0000 (19:41 +0300)]
EDAC, pnd2: Use proper I/O accessors and address space annotation
The driver uses rather voodoo kind of castings and I/O accessors.
Replace it with proper __iomem annotation and readl()/readq() calls.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Tested-by: Henning Schild <henning.schild@siemens.com> Reviewed-by: Tony Luck <tony.luck@intel.com> Signed-off-by: Lee Jones <lee@kernel.org>
Andy Shevchenko [Mon, 6 Jun 2022 16:41:32 +0000 (19:41 +0300)]
i2c: i801: convert to use common P2SB accessor
Since we have a common P2SB accessor in tree we may use it instead of
open coded variants.
Replace custom code by p2sb_bar() call.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Tested-by: Henning Schild <henning.schild@siemens.com> Acked-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Linus Walleij <linus.walleij@linaro.org> Reviewed-by: Jean Delvare <jdelvare@suse.de> Acked-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Lee Jones <lee@kernel.org>
Tan Jui Nee [Mon, 6 Jun 2022 16:41:31 +0000 (19:41 +0300)]
mfd: lpc_ich: Add support for pinctrl in non-ACPI system
Add support for non-ACPI systems, such as system that uses
Advanced Boot Loader (ABL) whereby a platform device has to be created
in order to bind with pin control and GPIO.
At the moment, Intel Apollo Lake In-Vehicle Infotainment (IVI) system
requires a driver to hide and unhide P2SB to lookup P2SB BAR and pass
the PCI BAR address to GPIO.
Signed-off-by: Tan Jui Nee <jui.nee.tan@intel.com> Co-developed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Tested-by: Henning Schild <henning.schild@siemens.com> Acked-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Lee Jones <lee@kernel.org>
Andy Shevchenko [Mon, 6 Jun 2022 16:41:30 +0000 (19:41 +0300)]
mfd: lpc_ich: Switch to generic p2sb_bar()
Instead of open coding p2sb_bar() functionality we are going to
use generic library. There is one more user en route.
This is more than just a clean-up. It also fixes a potential issue
seen when SPI BAR is 64-bit. The current code works if and only if
the PCI BAR of the hidden device is inside 4G address space. In case
when firmware decides to go above 4G, we will get a wrong address.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Tested-by: Henning Schild <henning.schild@siemens.com> Acked-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Lee Jones <lee@kernel.org>
Andy Shevchenko [Mon, 6 Jun 2022 16:41:29 +0000 (19:41 +0300)]
mfd: lpc_ich: Factor out lpc_ich_enable_spi_write()
Factor out duplicate code to lpc_ich_enable_spi_write() helper function.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Tested-by: Henning Schild <henning.schild@siemens.com> Acked-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Lee Jones <lee@kernel.org>
MIPS: cpuinfo: Fix a warning for CONFIG_CPUMASK_OFFSTACK
When CONFIG_CPUMASK_OFFSTACK and CONFIG_DEBUG_PER_CPU_MAPS is selected,
cpu_max_bits_warn() generates a runtime warning similar as below while
we show /proc/cpuinfo. Fix this by using nr_cpu_ids (the runtime limit)
instead of NR_CPUS to iterate CPUs.
Andy Shevchenko [Mon, 6 Jun 2022 16:41:28 +0000 (19:41 +0300)]
pinctrl: intel: Check against matching data instead of ACPI companion
In some cases we may get a platform device that has ACPI companion
which is different to the pin control described in the ACPI tables.
This is primarily happens when device is instantiated by board file.
In order to allow this device being enumerated, refactor
intel_pinctrl_get_soc_data() to check the matching data instead of
ACPI companion.
Reported-by: Henning Schild <henning.schild@siemens.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Tested-by: Henning Schild <henning.schild@siemens.com> Acked-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Lee Jones <lee@kernel.org>
Jonathan Yong [Mon, 6 Jun 2022 16:41:27 +0000 (19:41 +0300)]
platform/x86/intel: Add Primary to Sideband (P2SB) bridge support
SoC features such as GPIO are accessed via a reserved MMIO area,
we don't know its address but can obtain it from the BAR of
the P2SB device, that device is normally hidden so we have to
temporarily unhide it, read address and hide it back.
There are already a few users and at least one more is coming which
require an access to Primary to Sideband (P2SB) bridge in order
to get IO or MMIO BAR hidden by BIOS.
Create a library to access P2SB for x86 devices in a unified way.
Background information
======================
Note, the term "bridge" is used in the documentation and it has nothing
to do with a PCI (host) bridge as per the PCI specifications.
The P2SB is an interesting device by its nature and hardware design.
First of all, it has several devices in the hardware behind it. These
devices may or may not be represented as ACPI devices by a firmware.
It also has a hardwired (to 0s) the least significant bits of the
base address register which is represented by the only 64-bit BAR0.
It means that OS mustn't reallocate the BAR.
On top of that in some cases P2SB is represented by function 0 on PCI
slot (in terms of B:D.F) and according to the PCI specification any
other function can't be seen until function 0 is present and visible.
In the PCI configuration space of P2SB device the full 32-bit register
is allocated for the only purpose of hiding the entire P2SB device. As
per [3]:
3.1.39 P2SB Control (P2SBC)—Offset E0h
Hide Device (HIDE): When this bit is set, the P2SB will return 1s on
any PCI Configuration Read on IOSF-P. All other transactions including
PCI Configuration Writes on IOSF-P are unaffected by this. This does
not affect reads performed on the IOSF-SB interface.
This doesn't prevent MMIO accesses, although preventing the OS from
assigning these addresses. The firmware on the affected platforms marks
the region as unusable (by cutting it off from the PCI host bridge
resources) as depicted in the Apollo Lake example below:
PCI host bridge to bus 0000:00
pci_bus 0000:00: root bus resource [io 0x0070-0x0077]
pci_bus 0000:00: root bus resource [io 0x0000-0x006f window]
pci_bus 0000:00: root bus resource [io 0x0078-0x0cf7 window]
pci_bus 0000:00: root bus resource [io 0x0d00-0xffff window]
pci_bus 0000:00: root bus resource [mem 0x7c000001-0x7fffffff window]
pci_bus 0000:00: root bus resource [mem 0x7b800001-0x7bffffff window]
pci_bus 0000:00: root bus resource [mem 0x80000000-0xcfffffff window]
pci_bus 0000:00: root bus resource [mem 0xe0000000-0xefffffff window]
pci_bus 0000:00: root bus resource [bus 00-ff]
The P2SB 16MB BAR is located at 0xd0000000-0xd0ffffff memory window.
The generic solution
====================
The generic solution for all cases when we need to access to the information
behind P2SB device is a library code where users ask for necessary resources
by demand and hence those users take care of not being run on the systems
where this access is not required.
The library provides the p2sb_bar() API to retrieve the MMIO of the BAR0 of
the device from P2SB device slot.
P2SB unconditional unhiding awareness
=====================================
Technically it's possible to unhide the P2SB device and devices on
the same PCI slot and access them at any time as needed. But there are
several potential issues with that:
- the systems were never tested against such configuration and hence
nobody knows what kind of bugs it may bring, especially when we talk
about SPI NOR case which contains Intel FirmWare Image (IFWI) code
(including BIOS) and already known to be problematic in the past for
end users
- the PCI by its nature is a hotpluggable bus and in case somebody
attaches a driver to the functions of a P2SB slot device(s) the
end user experience and system behaviour can be unpredictable
- the kernel code would need some ugly hacks (or code looking as an
ugly hack) under arch/x86/pci in order to enable these devices on
only selected platforms (which may include CPU ID table followed by
a potentially growing number of DMI strings
The future improvements
=======================
The future improvements with this code may go in order to gain some kind
of cache, if it's possible at all, to prevent unhiding and hiding many
times to take static information that may be saved once per boot.
Signed-off-by: Jonathan Yong <jonathan.yong@intel.com> Co-developed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Tested-by: Henning Schild <henning.schild@siemens.com> Acked-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Lee Jones <lee@kernel.org>
Stefan Binding [Thu, 30 Jun 2022 00:23:28 +0000 (01:23 +0100)]
ALSA: hda: cs35l41: Support multiple load paths for firmware
To be able to support different firmwares and tuning
for different models, the driver needs to be able to
load a different firmware and coefficient file based
on its Subsystem ID.
The driver attempts to load the firmware in the
following order:
Stefan Binding [Thu, 30 Jun 2022 00:23:26 +0000 (01:23 +0100)]
ALSA: hda: cs35l41: Save Subsystem ID inside CS35L41 Driver
The Subsystem ID is read from the HDA driver, and will
be used by the CS35L41 driver to be able to uniquely
identify the laptop, which is required to be able to
define firmware to be used by specific models.
Vitaly Rodionov [Thu, 30 Jun 2022 00:23:25 +0000 (01:23 +0100)]
ALSA: hda: cs35l41: Add initial DSP support and firmware loading
This patch adds support for the CS35L41 DSP.
The DSP allows for extra features, such as running
speaker protection algorithms and hibernations.
To utilize these features, the driver must load
firmware into the DSP, as well as various tuning
files which allow for customization for specific
models.
Stefan Binding [Thu, 30 Jun 2022 00:23:23 +0000 (01:23 +0100)]
ALSA: hda: hda_cs_dsp_ctl: Add apis to write the controls directly
DSP controls are exposed as ALSA controls, however,
some of these controls are required to be accessed by
the driver. Add apis which allow read/write of these
controls. The write api will also notify the ALSA control
on value change.
projects / people / ms / linux.git / log
