git.ipfire.org Git - thirdparty/u-boot.git/log

sysinfo: rcar3: Fix Draak and Eagle board code

Correct the board code ID based on the hardware documentation

Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Tam Nguyen <tam.nguyen.xa@renesas.com>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>

pinctrl: renesas: Drop non-existent PFC info table entries

Remove PFC info table entries which are never instantiated,
since there are no drivers for those. No functional change.

Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>

clk: renesas: Always select DM_RESET to prevent inobvious failure of rst_gen3 subdriver

The CLK_RCAR_GEN3 registers two subdrivers, clk_gen3 and rst_gen3.
The former depends on the clock framework, which is always enabled
in this context of clock framework driver, while the later depends
on reset framework which may not always be enabled.

Ensure the reset framework is also always enabled to prevent inobvious
early boot time bind failure of the CPG driver, which leads to system
showing no activity and is difficult to debug.

Note that one possible approach to debug this is to use CONFIG_DEBUG_UART
and add debug printascii()s into the drivers/clk/renesas/clk-rcar-gen3.c .

Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>

mmc: renesas-sdhi: Add proper probe error fail path

In case one of the calls in probe fail, trigger a fail path and
undo all the steps done in probe until the point of failure.
The current implementation failed to stop controller clock and
free claimed clock, so fix that. Furthermore, print return code
in error prints for easier debugging.

Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>

mmc: renesas-sdhi: Always configure default SDnH clock rate to 800 MHz

The prior stage bootloader might have left the SDnCKCR register in completely
arbitrary state before passing control to U-Boot, which includes the register
being populated with incorrect values. Currently the SDHI driver will attempt
to use clock framework to configure SDn clock, which may fail in case SDnCKCR
contains invalid values for the SDnH clock, because the clock framework would
not be able to determine SDnH clock rate and would get -EINVAL instead, which
in turn would not allow the clock framework to determine the correct SDn clock
divider ratio.

This failure occurs specifically in case SDnCKCR reads back 0x209 .

Correct the problem by first setting default SDnH clock rate to 800 MHz, thus
assuring the SDnCKCR SDnH bits are correct, and only afterward set up the SDn
clock rate to default 200 MHz.

Note that the SDHI driver may reconfigure SDnH clock later based on IOS
settings obtained from the attached card, the 800 MHz set up here is only
the default value.

Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>

usb: move CONFIG_USB_HUB_DEBOUNCE_TIMEOUT to USB

This configuration setting is only relevant if the board supports USB.
It should not be in the main menu but in the USB menu.

The setting is only relevant in USB host mode.

Fixes: 5454dea3137d ("usb: hub: allow to increase HUB_DEBOUNCE_TIMEOUT")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>

usb: USB hubs require host mode

USB hubs run in host mode not in gadget mode. Hence, compiling usb_hub.c
should not be selected by CONFIG_USB_GADGET.

Suggested-by: Marek Vasut <marex@denx.de>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Marek Vasut <marex@denx.de>

test: cmd: fdt: Test fdt bootcpu

Add 'fdt bootcpu' test which works as follows:
- Create basic FDT, map it to sysmem
- Print the FDT bootcpu
- Set the FDT bootcpu and read the value back using 'fdt header get'
- Perform the previous step twice to validate bootcpu overwrite

The test case can be triggered using:
"
./u-boot -Dc 'ut fdt'
"
To dump the full output from commands used during test, add '-v' flag.

Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Simon Glass <sjg@chromium.org>

test: cmd: fdt: Test fdt rm

Add 'fdt rm' test which works as follows:
- Create fuller FDT, map it to sysmem
- Selectively delete nodes or properties by both path and aliases
- Verify created nodes or properties using fdt print command

The test case can be triggered using:
"
./u-boot -Dc 'ut fdt'
"
To dump the full output from commands used during test, add '-v' flag.

Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Simon Glass <sjg@chromium.org>

test: cmd: fdt: Test fdt mknode

Add 'fdt mknode' test which works as follows:
- Create fuller FDT, map it to sysmem
- Create node either in / or subnode
- Attempt to create node over existing node, which fails
- Attempt to create subnodes in non-existing nodes or aliases
- Verify created nodes using fdt list command

The test case can be triggered using:
"
./u-boot -Dc 'ut fdt'
"
To dump the full output from commands used during test, add '-v' flag.

Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Simon Glass <sjg@chromium.org>

test: cmd: fdt: Test fdt set

Add 'fdt set' test which works as follows:
- Create fuller FDT, map it to sysmem
- Set either existing property to overwrite it, or new property
- Test setting both single properties as well as string and integer arrays
- Test setting to non-existent nodes and aliases
- Verify set values using 'fdt get value'

The test case can be triggered using:
"
./u-boot -Dc 'ut fdt'
"
To dump the full output from commands used during test, add '-v' flag.

Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Simon Glass <sjg@chromium.org>

test: cmd: fdt: Test fdt get size

Add 'fdt get size' test which works as follows:
- Create fuller FDT, map it to sysmem
- Get size of various properties
- Get node count of available nodes
- Test non-existent nodes and properties

The test case can be triggered using:
"
./u-boot -Dc 'ut fdt'
"
To dump the full output from commands used during test, add '-v' flag.

Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Simon Glass <sjg@chromium.org>

test: cmd: fdt: Test fdt get addr

Add 'fdt get addr' test which works as follows:
- Create fuller FDT, map it to sysmem
- Get address of various properties
- Compare addresses calculated by UT and fdt command

This test is special in that it has to go through gruesome remapping scheme
where the test calculates:
- pointer offsets of the generated FDT root and the property being tested
- map_sysmem() result of environment variable "fdtaddr" and the one set
by the test matching address of property being tested
- difference between the later and the former, to obtain offset of the
DT property from start of DT
The offsets must match in both the UT and the tested U-Boot, if they do
not, the test fails.

The test case can be triggered using:
"
./u-boot -Dc 'ut fdt'
"
To dump the full output from commands used during test, add '-v' flag.

Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Simon Glass <sjg@chromium.org>

test: cmd: fdt: Test fdt get name

Add 'fdt get name' test which works as follows:
- Create fuller FDT, map it to sysmem
- Get name of / node 0, 1 and /clk-test node 0
- Compare output and validate the node name
- Get name of / node 2 and /clk-test node 1
- Compare output and validate the node is not present
- Get name of / node -1 and /clk-test node -1
- Compare output and validate the node name equals node 0 name
- Check nonexistent node, verify the command errors out

The test case can be triggered using:
"
./u-boot -Dc 'ut fdt'
"
To dump the full output from commands used during test, add '-v' flag.

Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Simon Glass <sjg@chromium.org>

test: cmd: fdt: Test fdt resize

Add 'fdt resize' test which works as follows:
- Create simple FDT with extra size 0, map it to sysmem
- 'resize' the FDT by 0x2000 bytes
- Verify the new space has been added to the FDT

The test case can be triggered using:
"
./u-boot -Dc 'ut fdt'
"
To dump the full output from commands used during test, add '-v' flag.

Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Simon Glass <sjg@chromium.org>

test: cmd: fdt: Test fdt move

Add 'fdt move' test which works as follows:
- Create simple FDT, map it to sysmem
- 'move' the FDT into new zeroed out sysmem location
- Verify newly active FDT is in the new location
- Compare both locations

The test case can be triggered using:
"
./u-boot -Dc 'ut fdt'
"
To dump the full output from commands used during test, add '-v' flag.

Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Simon Glass <sjg@chromium.org>

test: cmd: fdt: Test both string and integer arrays in 'fdt get value'

The 'fdt get value' subcommand now supports extraction of integer value
from integer arrays, add test for it, including a test for special case
unindexed integer array read, which is handled as hash and treated as a
long string instead of integer.

Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Simon Glass <sjg@chromium.org>

test: cmd: fdt: Test alias resolution in 'fdt get value'

The 'fdt' command help contains the following note:
"
Dereference aliases by omitting the leading '/', e.g. fdt print ethernet0.
"
Add test for it.

Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Simon Glass <sjg@chromium.org>

test: cmd: fdt: Generate fuller DT internally and switch fdt get value to it

Implement function to generate internal test DT fragment and switch
the 'fdt get value' test to this instead of depending on the sandbox
DT. Rename clk-test node to test-node node. This FDT fragment will be
reused by other tests. No functional change.

Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Simon Glass <sjg@chromium.org>

test: cmd: fdt: Rename fdt_test_get() to fdt_test_get_value()

The 'fdt get' command has a 'get value' subcommand, rename the fdt_test_get()
to fdt_test_get_value() to avoid confusion about what it is testing. There is
currently no get 'get name', 'get addr', 'get size' subcommand test.

Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Simon Glass <sjg@chromium.org>

test: cmd: fdt: Rename fdt_test_resize() to fdt_test_addr_resize()

The 'fdt' command has a 'resize' subcommand, rename the fdt_test_resize()
to fdt_test_addr_resize() to avoid confusion about what it is testing.
There is currently no resize test.

Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Simon Glass <sjg@chromium.org>

test: Add ut_assert_nextline_empty() empty line helper

Add helper macro to test for empty lines, which is an inobvious
wrapper around ut_assert_nextline("%s", "") .

Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Simon Glass <sjg@chromium.org>

cmd: fdt: Add support for integer arrays in fdt get value with index

Currently any integer array value is set as long up-to-40 character
hexadecimal string into environment variable when extracted from an
FDT using 'fdt get value path prop index', because the support for
handling integer arrays is not implemented, and fdt_value_env_set()
code falls back into the hash handling behavior instead.

Implement this support simply by checking whether user supplied any
index. If index is set and the property length is multiple of four,
then this is an integer array, and the code would extract value at
specified index.

There is a subtle change where default index is set to -1 instead of 0.
This is OK, since the only place which checks for index to be less or
equal zero is the string array handling code in fdt_value_env_set() and
that code would work perfectly well with index -1 too.

Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Simon Glass <sjg@chromium.org>

cmd: fdt: Map address returned from fdt get addr to sysmem

The address returned from 'fdt get addr' command must be mapped
into sysmem, as this is a working FDT. Access to this address
without mapping it would lead to crash e.g. in sandbox.

The following command triggers the crash:
"
./u-boot -Dc 'fdt addr $fdtcontroladdr ; fdt get addr var / compatible ; md $var'
"

Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Simon Glass <sjg@chromium.org>

cmd: fdt: Handle 64bit pointers in fdt get addr

The command assumed 32bit pointers so far, with 64bit pointer the
command would overwrite a piece of stack. Fix it by extending the
array size to cater for 64bit pointer, and use snprintf() to avoid
writing past the end of the array ever again.

Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Simon Glass <sjg@chromium.org>

cmd: fdt: Align checksign parameter names in help text

The help text references 'addr' as an optional key start address,
but the explanation references the same as 'start', make sure they
both read as 'addr'. Also update the abbreviated 'addr' in the
explanation to 'address'.

Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Simon Glass <sjg@chromium.org>

cmd: fdt: Check argc before accessing argv in fdt memory

On case 'fdt memory' is invoked without parameters, argv[2]/argv[3]
is not valid and this command would SEGFAULT in sandbox environment.
Add missing argc test to avoid the crash and rather print usage help
message.

Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Simon Glass <sjg@chromium.org>

cmd: fdt: Check argc before accessing argv in fdt bootcpu

On case 'fdt bootcpu' is invoked without parameters, argv[2] is not
valid and this command would SEGFAULT in sandbox environment. Add
missing argc test to avoid the crash and rather print usage help
message.

Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Simon Glass <sjg@chromium.org>

cmd: fdt: Fix fdt rsvmem behavior on non-existent index and error message space

In case 'fdt rsvmem delete index' is passed a non-existent index, one
which does not exist in 'fdt rsvmem print', then the following command
triggers a print of help message for 'fdt' command instead of erroring
out:
=> fdt rsvmem delete 1234
This is because the subcommand errornously returns 'err' instead of
CMD_RET_FAILURE, fix it. Furthermore, align the number of spaces past
fdt_del_mem_rsv() and fdt_add_mem_rsv() in error message with the rest
of the code.

Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Simon Glass <sjg@chromium.org>

cmd: fdt: Fix fdt rm behavior on non-existent property and error message space

In case an FDT contains a node '/test-node@1234' , with no property
called 'noprop' in that node, the following command triggers a print
of help message for 'fdt' command instead of erroring out:
=> fdt rm /test-node@1234 noprop
This is because the subcommand errornously returns 'err' instead of
CMD_RET_FAILURE, fix it. Furthermore, align the number of spaces past
fdt_delprop() in error message with the rest of the code.

Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Simon Glass <sjg@chromium.org>

cmd: fdt: Fix handling of empty properties for fdt get addr and fdt get size

It is perfectly valid to request an address or size of FDT property
without value, the only special case if requesting of the value of
FDT property without value. Invert the test such, that properties
without value still set the variable from 'fdt get addr/size' to
address of the property or size of the property, where the later
is 0.

Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Simon Glass <sjg@chromium.org>

cmd: fdt: Import is_printable_string() from DTC to fix u32 misprint

Import is_printable_string() implementation from DTC 1.7.0 as of
DTC commit 039a994 ("Bump version to v1.7.0") . This fixes a print
of u32 property which so far used to be printed as string by U-Boot
fdt print command.

We might see the case where the parsed property value, in this case
it is a 32-bit integer, identified as a printable string or a null byte
(concatenated strings) because of its last character happens to be:
  0x00 (null character), 0xB (vertical tab character) or
  0x10 (line feed character)
In this situation, if the string is identified as printable string,
it will be displayed as character instead of hex value

When the isprint() condition is true, there are two possibilities:
  1) The character is ASCII character (except the first 32)
  2) The character is extended ASCII character

For example,
NG property in device tree:
    clock-frequency = <16640000>;
by default, would be displayed as
    clock-frequency = "", "ýè";
and with this patch applied, would be displayed as
    clock-frequency = <0x00fde800>;

Full investigation was done by Nam and Hai, patch reworked by Marek
to use common code from DTC.

Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Nam Nguyen <nam.nguyen.yh@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Simon Glass <sjg@chromium.org>

Merge tag 'dm-next-9mar23' of https://source.denx.de/u-boot/custodians/u-boot-dm into next

binman x509, separate tools dir and other improvements
patman parallel patch generation
fdt fixes and tests
PyPi support for U-Boot tools
buildman reproducible builds

spl: Add missing prototype for board_boot_order

Add missing prototype to fix the sparse warning, warning: no
previous prototype for 'board_boot_order' [-Wmissing-prototypes].

Signed-off-by: Algapally Santosh Sagar <santoshsagar.algapally@amd.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20230301103334.1455-3-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>

xilinx: zynqmp: Add missing prototype for zynqmp_mmio_write

Add missing prototype to fix the sparse warning, warning: no
previous prototype for 'zynqmp_mmio_write' [-Wmissing-prototypes].

Signed-off-by: Algapally Santosh Sagar <santoshsagar.algapally@amd.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20230301103334.1455-2-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>

arm64: dts: zynqmp: Enable nand-on-flash-bbt in DT by default

By default enable nand-on-flash-bbt DT flag, so that driver always refers
to the bad block table(bbt) present on the flash device.

Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20230224050709.30014-5-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>

arm64: dts: zynqmp: Fix nand dt node

DC3 nand node is not correct, it is showing all partitions under
controller node directly. Create two sub nand nodes with partitions for
each.

Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20230224050709.30014-4-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>

mtd: nand: arasan: Set ofnode value

Ofnode value is not set, so all the DT properties are not being read
and due to this default values are being used.

Find nand node and set chip->flash_node value.

Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20230224050709.30014-3-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>

mtd: nand: arasan: Remove hardcoded bbt option

Bad block table option is hardcoded to read from flash with
NAND_BBT_USE_FLASH option. This decision should be done based on DT
property. Remove this hardcoding, to be able to use DT property.

Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20230224050709.30014-2-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>

spi: xilinx_spi: Fix spi reset

It was incorrectly using an old priv->regs pointer, which was
initialized to zero. SPI resets won't happen on first call.

Signed-off-by: Jiajie Chen <c@jia.je>
Link: https://lore.kernel.org/r/20230227150938.211820-1-c@jia.je
Signed-off-by: Michal Simek <michal.simek@amd.com>

arm64: zynqmp: Remove comment about gem spec in kv260

The latest SOM specification doesn't enforce certain MIO lines allocated
for ethernet or ethernet controller itself. That's why remove comment about
it which is likely there from early version of specification.
Also removed the same comment from pinctrl node. It is clear that it has to
be defined for different carrier cards.

Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/9406377bf2c391ac0200670511bd6b0edb097c96.1676880543.git.michal.simek@amd.com

xilinx: Enable SMC command for arm64 targets

SMC command is very useful for TF-A testing or issuing commands which are
not covered by any driver. Strongly recommend to disable this command on
any product unless it is required.

Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/23c77a2cbd083963ca17b84de4108dbb1f28597f.1676450712.git.michal.simek@amd.com

cmd: smccc: Print results in hex instead of dec

Printing return value in HEX instead of DEC. Return values are 64 bit
values which impossible to decode in DEC. For example getting CHIP ID in
dec is quite long.

Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/9a0278a7da729cb69b7a4d46c5e7eb8c3217c635.1676450712.git.michal.simek@amd.com

arm64: zynqmp: Add an OP-TEE node to the device tree

Since the zynqmp boards can run upstream OP-TEE, and having the DT node
present doesn't cause any side effects add it in case someone tries to
load OP-TEE.

Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Link: https://lore.kernel.org/r/20230216133921.866786-1-ilias.apalodimas@linaro.org
Signed-off-by: Michal Simek <michal.simek@amd.com>

fpga: zynqmppl: fix fpga loads command for unencrypted use case

When using the fpga loads command, the driver is passing the AES encryption
key address is all cases. However, for the authenticated, but not encrypted
use case, there is no AES encryption key, and this value is 0.

When AES encryption is not used on the fpga bitstream, the pmufw assumes that
the AES key address is a bitstream size value like what is used by the
unsecure fpga load command.

To fix the problem, this patch checks to see if the AES key address is zero.
If the AES key address is zero, it means that AES is not being used on the
bitstream and the bitstream size should be passed instead. Thus, matching
the fpga load functionality.

Signed-off-by: Neal Frager <neal.frager@amd.com>
Acked-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20230214131959.40298-1-neal.frager@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>

ARM: zynq: Comment interrupt names IRQs for pl330

pl330 DT yaml description doesn't define interrupt-names property that's
why comment it but keep it as comment.

Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/8e5a921c16efe09030fda036340186c11dd990bf.1672908030.git.michal.simek@amd.com

ARM: dts: zynq-7000: drop useless 'dma-channels/requests' properties

The pl330 DMA controller provides number of DMA channels and requests
through its registers, so duplicating this information (with a chance of
mistakes) in DTS is pointless. Additionally the DTS used always wrong
property names which causes DT schema check failures - the bindings
documented 'dma-channels' and 'dma-requests' properties without leading
hash sign.

Reported-by: Rob Herring <robh@kernel.org>
Suggested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/20220430121902.59895-2-krzysztof.kozlowski@linaro.org

ARM: dts: xilinx: align gpio-key node names with dtschema

The node names should be generic and DT schema expects certain pattern
(e.g. with key/button/switch).

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220616005333.18491-31-krzysztof.kozlowski@linaro.org
Signed-off-by: Michal Simek <michal.simek@amd.com>

ARM: zynq: Use recommended dma-controller name instead of dmac

Use standard name for dma controller. Issue is reported by dtbs_check as
dmac@f8003000: $nodename:0: 'dmac@f8003000' does not match
'^dma-controller(@.*)?$'

Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/5637d7e3464fbc1b2b269a7df35e24edc2c8d4ac.1672908080.git.michal.simek@amd.com

arm64: zynqmp: Enable hs termination flag for USB dwc3 controller

Since we need to support legacy phys with the dwc3 controller,
we enable this quirk on the zynqmp platforms.

Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Link: https://lore.kernel.org/r/20221023215649.221726-1-m.grzeschik@pengutronix.de
Signed-off-by: Michal Simek <michal.simek@amd.com>

arm64: dts: xilinx: align LED node names with dtschema

The node names should be generic and DT schema expects certain pattern:

xilinx/zynqmp-zcu100-revC.dtb: leds: 'vbus-det' does not match any of the regexes: '(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+'

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20221125144136.477171-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Michal Simek <michal.simek@amd.com>

xilinx: dts: Remove cdns,zynq-gem

cdns prefix was deprecated and replaced by xlnx one in upstream Linux. Also
U-Boot driver has been updated to support new compatible string that's why
it is time to remove it and deprecate it.

Signed-off-by: Michal Simek <michal.simek@amd.com>

arm64: zynqmp: Add missing ZYNQMP_FIRMWARE dependencies

There are missing Kconfig dependencies in the code which is using
firmware interface.
The commit 71efd45a5fc7 ("arm64: zynqmp: Change firmware dependency")
add option to also disable ZYNQMP_FIRMWARE. But not all Kconfig
dependencies were properly described and also sdhci and gem drivers
didn't protect the code properly.
So, add the missing ZYNQMP_FIRMWARE dependencies.

Signed-off-by: Algapally Santosh Sagar <santoshsagar.algapally@amd.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20230201095553.11219-1-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>

binman: Support generation of x509 certificates

And a new entry type which supports generation of x509 certificates.
This uses a new 'openssl' btool with just one operation so far.

Signed-off-by: Simon Glass <sjg@chromium.org>

binman: Support updating section contents

Implement this feature since it is useful for updating FITs within an
image.

Signed-off-by: Simon Glass <sjg@chromium.org>

binman: Handle missing bintools correctly in fit

At present these are handled as if they are allowed to be missing, but
this is only true if the -M flag is provided. Fix this and add a test.

Signed-off-by: Simon Glass <sjg@chromium.org>

binman: Allow preserving the output dir when replacing

Add these flags for the 'replace' subcommand too, to aid debugging.

Signed-off-by: Simon Glass <sjg@chromium.org>
44 2023 -0700

buildman: Correct CROSS_COMPILE output for sandbox

At present, 'buildman -A sandbox' adds the path containing the
toolchain at present. We can assume that this is in the path and
we don't want to set CROSS_COMPILE=/bin/ so change this to align
with what MakeEnvironment() does.

Signed-off-by: Simon Glass <sjg@chromium.org>

patman: Check patches in parallel

For large series this can take a while. Run checkpatch in parallel to
try to reduce the time. The checkpatch information is still reported in
sequential order, so a very slow patch at the start can still slow
things down. But overall this gives good results.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>

patman: Run get_maintainer.pl in parallel

This script can take ages on some series. Try to limit the time by
using threads. If a few stubborn patches remain, show progress so the
user has some idea what is going on.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>

patman: Refactor MakeCcFile() into two functions

This function is quite long. Moving the handling of a commit into a
separate function. This will make it easier to do the work in parallel.

Update function comments while we are here.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>

patman: Drop an incorrect comment about git am

Patman does not do this anymore, as of this commit:

7428dc14b0f ("patman: Remove the -a option")

Drop the comment.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>

test: cmd: fdt: Add list of remaining missing tests

Add list of missing tests for the 'fdt' command, currently
the missing sandbox tests are only 'fdt boardsetup' and
'fdt checksign' .

Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Simon Glass <sjg@chromium.org>