Pali Rohár [Fri, 26 Nov 2021 10:42:41 +0000 (11:42 +0100)]
pci: Add standard PCI Config Address macros
Lot of PCI and PCIe controllers are using standard Config Address for PCI
Configuration Mechanism #1 or its extended version.
So add PCI_CONF1_ADDRESS() and PCI_CONF1_EXT_ADDRESS() macros into U-Boot's
pci.h header file which can be suitable for most PCI and PCIe controller
drivers. Drivers do not have to invent their own macros and can use these
new U-Boot macros.
Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Simon Glass <sjg@chromium.org>
Pali Rohár [Thu, 25 Nov 2021 10:34:37 +0000 (11:34 +0100)]
pci: When disabling pref MEM set all base bits
It is common to set all base address bits to one and all limit address bits
to zero for disabling address forwarding. Forwarding is disabled when base
address is higher than limit address, so this change should not have any
effect.
Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Stefan Roese <sr@denx.de>
Pali Rohár [Thu, 25 Nov 2021 10:32:43 +0000 (11:32 +0100)]
pci: Disable I/O forwarding during autoconfiguration if unsupported
If U-Boot does not have any I/O resource for assignment then disable I/O
forwarding in PCI bridge autoconfiguration code. Default initial state of
PCI bridge IO registers is unspecified, therefore they can be in enabled if
U-Boot does not touch them.
Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Stefan Roese <sr@denx.de>
Pali Rohár [Thu, 25 Nov 2021 10:30:58 +0000 (11:30 +0100)]
pci: Fix register for determining type of IO base address
Function dm_pciauto_prescan_setup_bridge() configures base address
registers, therefore it should read type of IO from base address registers
(and not from limit address registers).
Note that base and limit address registers should have same type, so this
change is just usage correction and has no functional change on correctly
working hardware.
Fixes: 8e85f36a8fab ("pci: Fix configuring io/memory base and limit registers of PCI bridges") Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Stefan Roese <sr@denx.de>
Michal Simek [Thu, 6 Jan 2022 08:49:41 +0000 (09:49 +0100)]
phy: zynqmp: Add serdes/psgtr driver
Add PSGTR driver for Xilinx ZynqMP.
The most of configurations are taken from Linux kernel psgtr driver.
USB3.0 and SGMII configurations are tested on SOM. In SGMII case also
IOU_SLCR reg is updated to get proper clock setup and signal detection
configuration.
We want to replace '#ifdef' by 'if (IS_ENABLED(CONFIG_...))' in our code.
Therefore functions should be defined unconditionally even if they are not
implemented.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com> Acked-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
The initial clock setting should be through sysctl register only,
while the mmc_set_clock() will call mmc_set_ios() introduce other
configurations like bus width, mode, and so on.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com> Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Sean Anderson [Tue, 23 Nov 2021 20:03:46 +0000 (15:03 -0500)]
mmc: fsl_esdhc_imx: Replace more #ifdefs by if
This builds on the previous patch by converting yet more preprocessor
macros to C ifs. This is split off so that the changes adapted from
Micheal's patch may be clearly distinguished from the ones I have
authored myself.
MMC_SUPPORTS_TUNING should really get a Kconfig conversion. And DM_GPIO
needs some -ENOSYS stubs when it isn't defined.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
First, we need the waterlevel setting for PIO mode only. Secondy, both DMA
setup code is identical for both directions, except for the data pointer.
Thus, unify them.
Signed-off-by: Michael Walle <michael@walle.cc> Signed-off-by: Sean Anderson <sean.anderson@seco.com> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Use the dma_{map,unmap}_single() calls. These will take care of the
flushing and invalidation of caches.
Signed-off-by: Michael Walle <michael@walle.cc> Signed-off-by: Sean Anderson <sean.anderson@seco.com> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
SDMA can only do DMA with 32 bit addresses. This is true for all
architectures (just doesn't apply to 32 bit ones). Simplify the code and
remove unnecessary CONFIG_FSL_LAYERSCAPE.
Also make the error message more concise.
Signed-off-by: Michael Walle <michael@walle.cc> Signed-off-by: Sean Anderson <sean.anderson@seco.com> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
- For DM_MMC, remove getting "bus-width" from device tree.
This has been done in mmc_of_parse().
- For non-DM_MMC, move bus width configuration from fsl_esdhc_init()
to fsl_esdhc_initialize() which is non-DM_MMC specific.
And fix up bus width configuration to support only 1-bit, 4-bit,
or 8-bit. Keep using 8-bit if it's not set because many platforms
use driver without providing max bus width.
- Remove bus_width member from fsl_esdhc_priv structure.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
[ converted if statement to switch ] Signed-off-by: Sean Anderson <sean.anderson@seco.com> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Voltage validation should be done by CMD8. Current comparison between
mmc_cfg voltages and host voltage capabilities is meaningless.
So drop current comparison and let voltage validation is through CMD8.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com> Signed-off-by: Sean Anderson <sean.anderson@seco.com> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Sean Anderson [Tue, 11 Jan 2022 23:18:52 +0000 (08:18 +0900)]
mmc: fsl_esdhc_imx: make BLK as hard requirement of DM_MMC
U-boot prefers DM_MMC + BLK for MMC. Now eSDHC driver has already
support it, so let's force to use it.
- Drop non-BLK support for DM_MMC introduced by below patch. 66fa035 mmc: fsl_esdhc: fix probe issue without CONFIG_BLK enabled
- Support only DM_MMC + BLK (assuming BLK is always enabled for DM_MMC).
- Use DM_MMC instead of BLK for conditional compile.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com> Signed-off-by: Sean Anderson <sean.anderson@seco.com> Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Michal Simek [Tue, 11 Jan 2022 09:28:09 +0000 (10:28 +0100)]
net: uclass: Save generated ethernet MAC addresses to the environment
When a MAC address is randomly generated we currently only update the
appropriate data structure. For consistency and to re-align with
historic usage, it should be also saved to the appropriate environment
variable as well.
The return type of EVP_PKEY_get0_RSA() is const struct rsa_st *.
Our code drops the const qualifier leading to
In file included from tools/lib/rsa/rsa-sign.c:1:
./tools/../lib/rsa/rsa-sign.c: In function ‘rsa_add_verify_data’:
./tools/../lib/rsa/rsa-sign.c:631:13: warning:
assignment discards ‘const’ qualifier from pointer target type
[-Wdiscarded-qualifiers]
631 | rsa = EVP_PKEY_get0_RSA(pkey);
| ^
Add a type conversion.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Tom Rini [Sun, 9 Jan 2022 12:56:31 +0000 (07:56 -0500)]
Merge tag 'u-boot-amlogic-20220107' of https://source.denx.de/u-boot/custodians/u-boot-amlogic into next
- disable CONFIG_NET_RANDOM_ETHADDR when unnecessary on amlogic based configs
- meson64_android: add board specific env settings, in order to support VIM3/L for android
- add changes to support VIM3/L android boot by using meson64_android.h config
Patrick Wildt [Sat, 8 Jan 2022 15:34:17 +0000 (16:34 +0100)]
imx8mq: Generate a single bootable flash.bin again
All i.MX8MQ boards have been converted to binman, which makes it
necessary to flash both flash.bin and u-boot.itb to get a bootable
system. Prior to the conversion, only flash.bin was needed.
Such new requirement breaks existing distro mechanisms to generate the
final binary because the extra u-boot.itb is now required.
Generate a final flash.bin that can be used again as a single bootable
binary to keep the original behavior.
After this change the SPL binary is called spl.bin, which is a more
descriptive name for its purpose, and can still be used standalone (for
example, for secure boot purposes).
Also update imx8mq_evk.rst to remove the u-boot.itb copy step.
This is a cherry-pick of 028abfd9b157 ("imx8mm-evk: Generate a single
bootable flash.bin again") adjusted to apply to i.MX8MQ.
Signed-off-by: Patrick Wildt <patrick@blueri.se> Reviewed-by: Fabio Estevam <festevam@denx.de>
Gary Bisson [Wed, 5 Jan 2022 13:17:53 +0000 (14:17 +0100)]
nitrogen6x: add missing pinctrl to fix mmc
Since commit f7ac30b042d, the pin muxing for mmc was removed from the
board file to be managed by DM_MMC which requires PINCTRL to work. It
made the change for sabrelite but nitrogen configs were forgotten.
Gary Bisson [Thu, 6 Jan 2022 15:02:08 +0000 (16:02 +0100)]
usb: gadget: dwc2_udc_otg: set ep's desc during enable/disable
Fastboot support has been broken on platforms using dwc2 controller
since the gadget gets its max packet size from it.
This patch is the equivalent of 723fd5668ff which fixed the same issue
but for the chipidea controller.
Fixes: 27c9141b111 ("usb: gadget: fastboot: use correct max packet size") Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com> Reviewed-by: Neil Armstrong <narmstrong@baylibre.com> Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
- A large number of updates for i.MX8 platforms. We update buildman /
binman to be able to fake binaries if needed, for CI, and tell the user
the binary won't work. Update platforms to build again with these
changes.
The binman node is part of the imx8mm-u-boot.dtsi file which
is duplicated in imx8mm-kontron-n801x-s-u-boot.dtsi and causes
a build error. Remove the duplicate.
Fixes: 3cbb31f0e848 ("arm64: dts: imx8mm: use common binman configuration") Signed-off-by: Adam Ford <aford173@gmail.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
The binman node is part of the imx8mm-u-boot.dtsi file which
is duplicated in phycore-imx8mm-u-boot.dtsi and causes a build
error. Remove the duplicate.
Fixes: 3cbb31f0e848 ("arm64: dts: imx8mm: use common binman configuration") Signed-off-by: Adam Ford <aford173@gmail.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
Marcel Ziswiler [Fri, 22 Oct 2021 23:15:13 +0000 (01:15 +0200)]
arm64: dts: imx8mm: use common binman configuration
With the move to using binman to generate SPL aka u-boot-spl-ddr.bin and
U-Boot proper aka u-boot.itb every board now covers such configuration
in its own U-Boot specific device tree include. Move the comon part of
that configuration to the common imx8mm-u-boot.dtsi include file.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Peng Fan <peng.fan@nxp.com>
Adam Ford [Fri, 10 Sep 2021 20:19:22 +0000 (15:19 -0500)]
imx8mn_beacon: Fix booting hang and switch to binman
Somewhere along the line, the board stopped being able to boot.
Rather than just fixing the issue, let's fix the issue and migrate
to binman to eliminate a warning when using custom imx tools for
generating the binary.
Signed-off-by: Adam Ford <aford173@gmail.com> Reviewed-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
Heiko Thiery [Thu, 6 Jan 2022 10:49:41 +0000 (11:49 +0100)]
binman: add support for creating dummy files for external blobs
While converting to binman for an imx8mq board, it has been found that
building in the u-boot CI fails. This is because an imx8mq requires an
external binary (signed_hdmi_imx8m.bin). If this file cannot be found
mkimage fails.
To be able to build this board in the u-boot CI a binman option
(--fake-ext-blobs) is introduced that can be switched on via the u-boot
makefile option BINMAN_FAKE_EXT_BLOBS. With that the needed dummy files are
created.
Signed-off-by: Heiko Thiery <heiko.thiery@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
- Revert a clk change, to enable some platforms to work again
- Updates to the udoo NEO family of boards to work correctly
- Fix SiFive Unleashes/Unmatched boards booting
- Update rockchip maintainer entry
Marek Vasut [Sat, 1 Jan 2022 18:51:39 +0000 (19:51 +0100)]
Revert "clk: Detect failure to set defaults"
This reverts commit 92f1e9a4b31c0bf0f4f61ab823a6a88657323646.
The aforementioned patch causes massive breakage on all platforms which
have 'assigned-clock' DT property in their DT which references any clock
that are not supported by the platform clock driver. That can easily
happen either in SPL, or because the clock driver is reduced. Currently
it seems all iMX8M are affected and fail to boot altogether.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Peng Fan <peng.fan@oss.nxp.com> Cc: Simon Glass <sjg@chromium.org> Reviewed-by: Sean Anderson <seanga2@gmail.com> Reviewed-by: Fabio Estevam <festevam@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Peter Robinson [Tue, 21 Dec 2021 12:32:48 +0000 (12:32 +0000)]
udoo_neo: Fix ethernet
The ethernet has a RMII not RGMII, also needs DM_MDIO and finally
initialise it later in the process as it's not needed that early on
and not everything is ready so it locks up the device.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
Peter Robinson [Tue, 21 Dec 2021 12:32:47 +0000 (12:32 +0000)]
udoo_neo: Fixes for booting from the mSD card
This fixes booting from the mSD card from both SPL and when
using it for the OS booting. It also cleans up a few mmc
booting bits that are no longer needed.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
Bin Meng [Wed, 5 Jan 2022 01:07:57 +0000 (09:07 +0800)]
riscv: sifive: Fix OF_BOARD boot failure
When using QEMU to have a quick test of booting U-Boot S-mode payload
directly without the needs of preparing the SPI flash or SD card images
for SiFive Unleashed board, as per the instructions [1], it currently
does not boot any more.
This was caused by the OF_PRIOR_STAGE removal, as gd->fdt_blob no longer
points to a valid DTB. OF_BOARD is supposed to replace OF_PRIOR_STAGE,
hence we need to add the OF_BOARD logic in board_fdt_blob_setup().
configs: add khadas-vim3{l}_android for AOSP support
The Khadas VIM3 and VIM3L board are well supported in AOSP[1].
However, there is no mainline U-Boot support for it.
The U-Boot used in AOSP is based on a vendor tree [2]
Add all the necessary bits to flash and boot Android for both Khadas
VIM3 and VIM3L boards.
Neil Armstrong [Mon, 22 Nov 2021 11:07:10 +0000 (12:07 +0100)]
configs: amlogic: Disable CONFIG_NET_RANDOM_ETHADDR when unnecessary
On Meson GXL, GXM, AXG, G12A, G12B & SM1 SoCs, we can generate an unique
MAC address if none valid found in the eFuses storage.
Only the GXBB based boards doesn't have a fallback way to generate an
unique MAC address, so we rely on CONFIG_NET_RANDOM_ETHADDR to have
a valid one.
An exception is the Radxa Zero board who doesn't have Ethernet on board
so depends on an (or multiple) eventual USB adapters, so leaving the
CONFIG_NET_RANDOM_ETHADDR configs seems safer.
Pierre Bourdon [Sat, 25 Dec 2021 19:50:19 +0000 (20:50 +0100)]
tools: kwbimage: Fix checksum calculation for v1 images
Recent changes caused fields in the image main header to be modified
after the header checksum had already been computed. Move the checksum
computation to once again be the last operation performed on the header.
Fixes: 2b0980c24027 ("tools: kwbimage: Fill the real header size into the main header") Signed-off-by: Pierre Bourdon <delroth@gmail.com> Reviewed-by: Pali Rohár <pali@kernel.org> Reviewed-by: Stefan Roese <sr@denx.de>
Michal Simek [Mon, 6 Dec 2021 15:25:20 +0000 (16:25 +0100)]
net: zynq: Add support for GEM reset
Perform reset before core initialization.
Standard flow which close to 99% users are using getting all IPs out of
reset that there is no need to reset IP again. This is because of all low
level initialization is done in previous bootloader stage.
In SOM case these IPs are not touched by previous bootloader stage that's
why reset needs to be called before IP is accessed to make sure that it is
in correct state.
Michal Simek [Mon, 6 Dec 2021 13:53:17 +0000 (14:53 +0100)]
net: zynq: Add support for mdio bus address decoding
Xilinx DTS files are using two way how to describe ethernet phy.
The first (already supported) has phy as subnode of gem node.
eth {
phy-handle = <&phy0>;
phy0: ethernet-phy@21 {
...
};
};
The second has mdio subnode (with mdio name) which has phy subnode. This
structure allow hadling MDIO reset signal (based on Linux mdio.yaml)
eth {
phy-handle = <&phy0>;
mdio {
phy0: ethernet-phy@21 {
...
};
};
};
This patch adds support for the second case where mdio subnode
is found driver will look at its parent to find out which gem is handling
MDIO bus.
T Karthik Reddy [Wed, 24 Nov 2021 11:16:55 +0000 (12:16 +0100)]
versal: Return ENVL_NOWHERE instead of ENVL_UNKNOWN
The system fails to boot without any environment location, so return
ENVL_NOWHERE when there's nowhere to store the environment instead
of ENVL_UNKNOWN.
The same change was also done by commit 50918d0df5cb ("xilinx: Return
ENVL_NOWHERE instead of ENVL_UNKNOWN") for zynq and zynqmp.
Ovidiu Panait [Thu, 2 Dec 2021 19:56:56 +0000 (21:56 +0200)]
xilinx: Kconfig: add XILINX_OF_BOARD_DTB_ADDR default value for microblaze
The xilinx board_fdt_blob_setup() implementation makes use of
XILINX_OF_BOARD_DTB_ADDR, but no default value is currently defined for
microblaze. Add one so that microblaze could also work with
CONFIG_OF_SEPARATE.
Ovidiu Panait [Tue, 30 Nov 2021 16:33:57 +0000 (18:33 +0200)]
microblaze: branch to base vector address on reset
Current code assumes that the vector base address is always at 0x0.
However, this value is configurable for MicroBlaze using the
CONFIG_XILINX_MICROBLAZE0_VECTOR_BASE_ADDR Kconfig option. Update the
reset routines to branch to this location instead.
Ovidiu Panait [Tue, 30 Nov 2021 16:33:56 +0000 (18:33 +0200)]
microblaze: start.S: add support for configurable vector base address
Current code assumes that the vector base address is always at 0x0.
However, this value is configurable for MicroBlaze, so update the
__setup_exceptions routine to work with any vector base address.
The r4 register is reserved for the vector base address inside
__setup_exceptions and the function prologe/epilogue are also updated to
save and restore r4.
Ovidiu Panait [Tue, 30 Nov 2021 16:33:55 +0000 (18:33 +0200)]
microblaze: add Kconfig symbol for the vector base address
MicroBlaze vector base address is configurable (hdl C_BASE_VECTORS
configuration parameter). Current code assumes that the reset vector
location is always 0x0.
Add the XILINX_MICROBLAZE0_VECTOR_BASE_ADDR Kconfig option so the user
can adjust the reset vector address.
Ovidiu Panait [Tue, 30 Nov 2021 16:33:54 +0000 (18:33 +0200)]
microblaze: migrate CONFIG_SYS_USR_EXCEP to Kconfig
Migrate CONFIG_SYS_USR_EXCEP to Kconfig. Also, rename it to
XILINX_MICROBLAZE0_USR_EXCEP in order to match the naming convention of
microblaze-generic Kconfig options.
Ovidiu Panait [Tue, 30 Nov 2021 16:33:53 +0000 (18:33 +0200)]
microblaze: drop CONFIG_SYS_RESET_ADDRESS macro
Microblaze is one the last two users of the CONFIG_SYS_RESET_ADDRESS
macro (the other is arch/powerpc/cpu/mpc8xx/cpu.c, but the macro is not
defined anywhere in powerpc code, so it should be removed there too).
Replace CONFIG_SYS_RESET_ADDRESS usage in start.S with
CONFIG_SYS_TEXT_BASE. If the reset address should really be
user-configurable, a new Kconfig option could be added.
Ovidiu Panait [Tue, 30 Nov 2021 16:33:51 +0000 (18:33 +0200)]
microblaze: Kconfig: SPL dependencies fixup
Enable SPL_LIBCOMMON_SUPPORT and SPL_LIBGENERIC_SUPPORT if CONFIG_SPL=y, in
order to fix the following link failures:
common/spl/spl.o: in function `board_init_r':
common/spl/spl.c:755: undefined reference to `puts'
...
common/spl/spl.o: in function `board_init_r':
common/spl/spl.c:756: undefined reference to `hang'
common/spl/spl.c:740: undefined reference to `memset'
Microblaze has three boot modes defined in microblaze/include/asm/spl.h,
but only booting from NOR flash is currently useable. Add a custom
board_boot_order() implementation so that RAM and SPI boot modes can also
be selected if the corresponding load-image support is present.
Ovidiu Panait [Tue, 30 Nov 2021 16:33:49 +0000 (18:33 +0200)]
microblaze: u-boot.lds: replace __end symbol with _end
board_fdt_blob_setup() uses the _end symbol to find the dtb in the non-spl
case. In order to allow microblaze builds to compile successfully with
CONFIG_OF_SEPARATE, the _end symbol must be defined. Align microblaze with
the other architectures and use _end symbol rather than __end to mark the
end of the u-boot binary.
Michal Simek [Thu, 18 Nov 2021 12:00:02 +0000 (13:00 +0100)]
xilinx: firmware: Move dcache handling directly to pmufw load config
Core function should make sure that data is stored properly that's why move
cache operations directly to zynqmp_pmufw_load_config_object() to be able
to call it from other functions.
Michal Simek [Thu, 18 Nov 2021 11:58:15 +0000 (12:58 +0100)]
arm64: zynqmp: Switch SOM to shared psu configuration
Previous psu init was targeting SOM + KV260 carrier card and also contain
configurations for other devices on carrier card. This config is removing
all expected configurations for CC and let U-Boot to handle all of it self.
This configuration is designed for SOM itself (and I would bet without
eMMC).
projects / thirdparty / u-boot.git / log
