realtek: reorganize DTS for Zyxel XS1930

XS1930-10 and XS1930-12HP share most of their layout: the same
8-port AQR813 Base-T block, the same SFP+ GPIO mux, identical I2C
master config and serdes polarity. Carve those shared pieces out
into a new intermediate rtl9313_zyxel_xs1930-aqr813.dtsi and have both
device DTS files include it, leaving only their device-specific
differences (LED-set masks, extra PoE bits on -12HP, extra AQR113C
PHYs on -12HP) in the per-device files. XS1930-12F continues to
include the common DTSI directly since its layout differs too much
to share usefully.

Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/23428
Signed-off-by: Robert Marko <robimarko@gmail.com>

diff --git a/target/linux/realtek/dts/rtl9313_zyxel_xs1930-10.dts b/target/linux/realtek/dts/rtl9313_zyxel_xs1930-10.dts
index 4d217bf67b64938ddef72cda82cb624ea6eb6066..bac48c15fe87f1e9c756d0a3a448b01eb3e940c4 100644 (file)
--- a/target/linux/realtek/dts/rtl9313_zyxel_xs1930-10.dts
+++ b/target/linux/realtek/dts/rtl9313_zyxel_xs1930-10.dts
@@ -1,7 +1,7 @@
 // SPDX-License-Identifier: GPL-2.0-or-later
 /dts-v1/;
 
-#include "rtl9313_zyxel_xs1930.dtsi"
+#include "rtl9313_zyxel_xs1930-aqr813.dtsi"
 
 #include <dt-bindings/input/input.h>
 #include <dt-bindings/gpio/gpio.h>
@@ -12,104 +12,10 @@
 / {
        compatible = "zyxel,xs1930-10", "realtek,rtl9313-soc";
        model = "Zyxel XS1930-10";
-
-       led_set: led_set@0 {
-               compatible = "realtek,rtl9300-leds";
-               active-low;
-
-               /* Blue | Green | Red */
-               led_set0 = <(RTL93XX_LED_SET_10G | RTL93XX_LED_SET_5G | RTL93XX_LED_SET_2P5G |
-                            RTL93XX_LED_SET_LINK | RTL93XX_LED_SET_ACT)
-                           (RTL93XX_LED_SET_2P5G | RTL93XX_LED_SET_1G | RTL93XX_LED_SET_100M |
-                            RTL93XX_LED_SET_LINK | RTL93XX_LED_SET_ACT)
-                           (RTL93XX_LED_SET_5G | RTL93XX_LED_SET_100M | RTL93XX_LED_SET_LINK |
-                            RTL93XX_LED_SET_ACT)>;
-
-               realtek,led-set0-force-port-mask = <0x00300000 0x00000000>;
-       };
-
-       sfp_gpio_mux: gpio-mux {
-               compatible = "gpio-mux";
-               mux-gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>,
-                           <&gpio0 14 GPIO_ACTIVE_HIGH>;
-               #mux-control-cells = <0>;
-               idle-state = <MUX_IDLE_AS_IS>;
-       };
-
-       sfp1_gpio: sfp-gpio-1 {
-               compatible = "gpio-line-mux";
-               gpio-controller;
-               #gpio-cells = <2>;
-
-               mux-controls = <&sfp_gpio_mux>;
-               muxed-gpio = <&gpio0 19 GPIO_ACTIVE_HIGH>;
-
-               gpio-line-names = "SFP1_LOS", "SFP1_MOD_ABS", "SFP1_TX_FAULT";
-               gpio-line-mux-states = <0>, <1>, <3>;
-       };
-
-       sfp2_gpio: sfp-gpio-2 {
-               compatible = "gpio-line-mux";
-               gpio-controller;
-               #gpio-cells = <2>;
-
-               mux-controls = <&sfp_gpio_mux>;
-               muxed-gpio = <&gpio0 27 GPIO_ACTIVE_HIGH>;
-
-               gpio-line-names = "SFP2_LOS", "SFP2_MOD_ABS", "SFP2_TX_FAULT";
-               gpio-line-mux-states = <0>, <1>, <3>;
-       };
-
-       sfp1: sfp-p1 {
-               compatible = "sff,sfp";
-               i2c-bus = <&i2c0>;
-               los-gpio = <&sfp1_gpio 0 GPIO_ACTIVE_HIGH>;
-               mod-def0-gpio = <&sfp1_gpio 1 GPIO_ACTIVE_LOW>;
-               tx-disable-gpio = <&gpio0 5 GPIO_ACTIVE_HIGH>;
-               tx-fault-gpio = <&sfp1_gpio 2 GPIO_ACTIVE_HIGH>;
-       };
-
-       sfp2: sfp-p2 {
-               compatible = "sff,sfp";
-               i2c-bus = <&i2c1>;
-               los-gpio = <&sfp2_gpio 0 GPIO_ACTIVE_HIGH>;
-               mod-def0-gpio = <&sfp2_gpio 1 GPIO_ACTIVE_LOW>;
-               tx-disable-gpio = <&gpio0 11 GPIO_ACTIVE_HIGH>;
-               tx-fault-gpio = <&sfp2_gpio 2 GPIO_ACTIVE_HIGH>;
-       };
 };
 
-&gpio0 {
-       pinctrl-names = "default";
-       pinctrl-0 = <&pinmux_disable_jtag>;
-
-       sfp_enable_hog {
-               gpio-hog;
-               gpios = <6 GPIO_ACTIVE_LOW>,
-                       <7 GPIO_ACTIVE_LOW>;
-               output-high;
-               line-name = "sfp-enable";
-       };
-};
-
-&i2c_mst1 {
-       status = "okay";
-
-       i2c0: i2c@0 {
-               reg = <0>;
-       };
-       i2c1: i2c@1 {
-               reg = <1>;
-       };
-
-       i2c2: i2c@2 {
-               reg = <2>;
-
-               lm96000: lm96000@2e {
-                       compatible = "national,lm85";
-                       reg = <0x2e>;
-               };
-       };
+&led_set {
+       realtek,led-set0-force-port-mask = <0x00300000 0x00000000>;
 };
 
 &mdio_ctrl {
@@ -117,106 +23,9 @@
        pinctrl-0 = <&pinmux_enable_mdc_mdio_0>;
 };
 
-&mdio_bus0 {
-       /* External Aquantia AQR813 */
-       PHY_C45(0, 8)
-       PHY_C45(8, 9)
-       PHY_C45(16, 10)
-       PHY_C45(24, 11)
-       PHY_C45(32, 12)
-       PHY_C45(40, 13)
-       PHY_C45(48, 14)
-       PHY_C45(50, 15)
-};
-
 &switch0 {
        ethernet-ports {
-               #address-cells = <1>;
-               #size-cells = <0>;
-
-               /* Copper ports behind AQR813 */
-               SWITCH_PORT_LED(0, 1, 2, 0, usxgmii)
-               SWITCH_PORT_LED(8, 2, 3, 0, usxgmii)
-               SWITCH_PORT_LED(16, 3, 4, 0, usxgmii)
-               SWITCH_PORT_LED(24, 4, 5, 0, usxgmii)
-               SWITCH_PORT_LED(32, 5, 6, 0, usxgmii)
-               SWITCH_PORT_LED(40, 6, 7, 0, usxgmii)
-               SWITCH_PORT_LED(48, 7, 8, 0, usxgmii)
-               SWITCH_PORT_LED(50, 8, 9, 0, usxgmii)
-
-               /* SFP+ ports */
                SWITCH_PORT_SFP(54, 9, 12, 0, 1)
                SWITCH_PORT_SFP(55, 10, 13, 0, 2)
-
-               /* CPU port */
-               port@56 {
-                       reg = <56>;
-                       ethernet = <&ethernet0>;
-                       phy-mode = "internal";
-                       fixed-link {
-                               speed = <1000>;
-                               full-duplex;
-                       };
-               };
        };
 };
-
-&port0 {
-       managed = "in-band-status";
-};
-
-&port8 {
-       managed = "in-band-status";
-};
-
-&port16 {
-       managed = "in-band-status";
-};
-
-&port24 {
-       managed = "in-band-status";
-};
-
-&port32 {
-       managed = "in-band-status";
-};
-
-&port40 {
-       managed = "in-band-status";
-};
-
-&port48 {
-       managed = "in-band-status";
-};
-
-&port50 {
-       managed = "in-band-status";
-};
-
-&serdes6 {
-       rx-polarity = <PHY_POL_INVERT>;
-       tx-polarity = <PHY_POL_INVERT>;
-};
-
-&serdes7 {
-       rx-polarity = <PHY_POL_INVERT>;
-       tx-polarity = <PHY_POL_INVERT>;
-};
-
-&serdes8 {
-       rx-polarity = <PHY_POL_INVERT>;
-       tx-polarity = <PHY_POL_INVERT>;
-};
-
-&serdes9 {
-       rx-polarity = <PHY_POL_INVERT>;
-       tx-polarity = <PHY_POL_INVERT>;
-};
-
-&serdes12 {
-       tx-polarity = <PHY_POL_INVERT>;
-};
-
-&serdes13 {
-       tx-polarity = <PHY_POL_INVERT>;
-};

diff --git a/target/linux/realtek/dts/rtl9313_zyxel_xs1930-12hp.dts b/target/linux/realtek/dts/rtl9313_zyxel_xs1930-12hp.dts
index 5289c1eaa598de1981f4847eb5f83f752d4c05f4..bd203b81376745ad4588bd6de1af804eb515f8f0 100644 (file)
--- a/target/linux/realtek/dts/rtl9313_zyxel_xs1930-12hp.dts
+++ b/target/linux/realtek/dts/rtl9313_zyxel_xs1930-12hp.dts
@@ -1,7 +1,7 @@
 // SPDX-License-Identifier: GPL-2.0-or-later
 /dts-v1/;
 
-#include "rtl9313_zyxel_xs1930.dtsi"
+#include "rtl9313_zyxel_xs1930-aqr813.dtsi"
 
 #include <dt-bindings/input/input.h>
 #include <dt-bindings/gpio/gpio.h>
@@ -12,96 +12,26 @@
 / {
        compatible = "zyxel,xs1930-12hp", "realtek,rtl9313-soc";
        model = "Zyxel XS1930-12HP";
+};
 
-       led_set: led_set@0 {
-               compatible = "realtek,rtl9300-leds";
-               active-low;
-
-               /* Blue | Green | Red */
-               led_set0 = <(RTL93XX_LED_SET_10G | RTL93XX_LED_SET_5G | RTL93XX_LED_SET_2P5G |
-                            RTL93XX_LED_SET_LINK | RTL93XX_LED_SET_ACT)
-                           (RTL93XX_LED_SET_2P5G | RTL93XX_LED_SET_1G | RTL93XX_LED_SET_100M |
-                            RTL93XX_LED_SET_LINK | RTL93XX_LED_SET_ACT)
-                           (RTL93XX_LED_SET_5G | RTL93XX_LED_SET_100M | RTL93XX_LED_SET_LINK |
-                            RTL93XX_LED_SET_ACT)>;
-               /* Phantom port chain padding (2 LEDs) */
-               led_set1 = <RTL93XX_LED_SET_NONE
-                           RTL93XX_LED_SET_NONE>;
-
-               /* The LED PCB has two daisy-chained RTL8231 in scan mode.
-                * Net LEDs for P3-P12 are on the first RTL8231, P1/P2
-                * net LEDs are on the second. The 12 real ports provide
-                * 36 LED bits but the chain requires 65 bits to correctly
-                * span both chips. Phantom ports 1-7, 9-10 (set0, 3 LEDs
-                * each) and port 11 (set1, 2 LEDs) pad the chain with
-                * the remaining 29 bits.
-                */
-               realtek,led-set0-force-port-mask = <0x00000000 0x000006FE>;
-               realtek,led-set1-force-port-mask = <0x00000000 0x00000800>;
-       };
-
-       sfp_gpio_mux: gpio-mux {
-               compatible = "gpio-mux";
-               mux-gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>,
-                           <&gpio0 14 GPIO_ACTIVE_HIGH>;
-               #mux-control-cells = <0>;
-               idle-state = <MUX_IDLE_AS_IS>;
-       };
-
-       sfp1_gpio: sfp-gpio-1 {
-               compatible = "gpio-line-mux";
-               gpio-controller;
-               #gpio-cells = <2>;
-
-               mux-controls = <&sfp_gpio_mux>;
-               muxed-gpio = <&gpio0 19 GPIO_ACTIVE_HIGH>;
-
-               gpio-line-names = "SFP1_LOS", "SFP1_MOD_ABS", "SFP1_TX_FAULT";
-               gpio-line-mux-states = <0>, <1>, <3>;
-       };
-
-       sfp2_gpio: sfp-gpio-2 {
-               compatible = "gpio-line-mux";
-               gpio-controller;
-               #gpio-cells = <2>;
-
-               mux-controls = <&sfp_gpio_mux>;
-               muxed-gpio = <&gpio0 27 GPIO_ACTIVE_HIGH>;
+&led_set {
+       /* Phantom port chain padding (2 LEDs) */
+       led_set1 = <RTL93XX_LED_SET_NONE
+                   RTL93XX_LED_SET_NONE>;
 
-               gpio-line-names = "SFP2_LOS", "SFP2_MOD_ABS", "SFP2_TX_FAULT";
-               gpio-line-mux-states = <0>, <1>, <3>;
-       };
-
-       sfp1: sfp-p1 {
-               compatible = "sff,sfp";
-               i2c-bus = <&i2c0>;
-               los-gpio = <&sfp1_gpio 0 GPIO_ACTIVE_HIGH>;
-               mod-def0-gpio = <&sfp1_gpio 1 GPIO_ACTIVE_LOW>;
-               tx-disable-gpio = <&gpio0 5 GPIO_ACTIVE_HIGH>;
-               tx-fault-gpio = <&sfp1_gpio 2 GPIO_ACTIVE_HIGH>;
-       };
-
-       sfp2: sfp-p2 {
-               compatible = "sff,sfp";
-               i2c-bus = <&i2c1>;
-               los-gpio = <&sfp2_gpio 0 GPIO_ACTIVE_HIGH>;
-               mod-def0-gpio = <&sfp2_gpio 1 GPIO_ACTIVE_LOW>;
-               tx-disable-gpio = <&gpio0 11 GPIO_ACTIVE_HIGH>;
-               tx-fault-gpio = <&sfp2_gpio 2 GPIO_ACTIVE_HIGH>;
-       };
+       /* The LED PCB has two daisy-chained RTL8231 in scan mode.
+        * Net LEDs for P3-P12 are on the first RTL8231, P1/P2
+        * net LEDs are on the second. The 12 real ports provide
+        * 36 LED bits but the chain requires 65 bits to correctly
+        * span both chips. Phantom ports 1-7, 9-10 (set0, 3 LEDs
+        * each) and port 11 (set1, 2 LEDs) pad the chain with
+        * the remaining 29 bits.
+        */
+       realtek,led-set0-force-port-mask = <0x00000000 0x000006FE>;
+       realtek,led-set1-force-port-mask = <0x00000000 0x00000800>;
 };
 
 &gpio0 {
-       pinctrl-names = "default";
-       pinctrl-0 = <&pinmux_disable_jtag>;
-
-       sfp_enable_hog {
-               gpio-hog;
-               gpios = <6 GPIO_ACTIVE_LOW>,
-                       <7 GPIO_ACTIVE_LOW>;
-               output-high;
-               line-name = "sfp-enable";
-       };
        poe_enable_hog {
                gpio-hog;
                gpios = <10 GPIO_ACTIVE_HIGH>;
@@ -111,25 +41,6 @@
 };
 
 &i2c_mst1 {
-       status = "okay";
-
-       i2c0: i2c@0 {
-               reg = <0>;
-       };
-
-       i2c1: i2c@1 {
-               reg = <1>;
-       };
-
-       i2c2: i2c@2 {
-               reg = <2>;
-
-               lm96000: lm96000@2e {
-                       compatible = "national,lm85";
-                       reg = <0x2e>;
-               };
-       };
-
        /* PoE management MCU sits here */
        i2c3: i2c@3 {
                reg = <3>;
@@ -143,18 +54,6 @@
                    <&pinmux_enable_mdc_mdio_2>;
 };
 
-&mdio_bus0 {
-       /* AQR813 */
-       PHY_C45(0, 8)
-       PHY_C45(8, 9)
-       PHY_C45(16, 10)
-       PHY_C45(24, 11)
-       PHY_C45(32, 12)
-       PHY_C45(40, 13)
-       PHY_C45(48, 14)
-       PHY_C45(50, 15)
-};
-
 &mdio_bus1 {
        PHY_C45(52, 0)  /* AQR113C */
 };
@@ -165,72 +64,15 @@
 
 &switch0 {
        ethernet-ports {
-               #address-cells = <1>;
-               #size-cells = <0>;
-
-               /* Copper ports behind AQR813 */
-               SWITCH_PORT_LED(0, 1, 2, 0, usxgmii)
-               SWITCH_PORT_LED(8, 2, 3, 0, usxgmii)
-               SWITCH_PORT_LED(16, 3, 4, 0, usxgmii)
-               SWITCH_PORT_LED(24, 4, 5, 0, usxgmii)
-               SWITCH_PORT_LED(32, 5, 6, 0, usxgmii)
-               SWITCH_PORT_LED(40, 6, 7, 0, usxgmii)
-               SWITCH_PORT_LED(48, 7, 8, 0, usxgmii)
-               SWITCH_PORT_LED(50, 8, 9, 0, usxgmii)
-
                /* Copper ports behind AQR113C */
                SWITCH_PORT_LED(52, 9, 10, 0, usxgmii)
                SWITCH_PORT_LED(53, 10, 11, 0, usxgmii)
 
-               /* SFP+ ports */
                SWITCH_PORT_SFP(54, 11, 12, 0, 1)
                SWITCH_PORT_SFP(55, 12, 13, 0, 2)
-
-               /* CPU port */
-               port@56 {
-                       ethernet = <&ethernet0>;
-                       reg = <56>;
-                       phy-mode = "internal";
-                       fixed-link {
-                               speed = <1000>;
-                               full-duplex;
-                       };
-               };
        };
 };
 
-&port0 {
-       managed = "in-band-status";
-};
-
-&port8 {
-       managed = "in-band-status";
-};
-
-&port16 {
-       managed = "in-band-status";
-};
-
-&port24 {
-       managed = "in-band-status";
-};
-
-&port32 {
-       managed = "in-band-status";
-};
-
-&port40 {
-       managed = "in-band-status";
-};
-
-&port48 {
-       managed = "in-band-status";
-};
-
-&port50 {
-       managed = "in-band-status";
-};
-
 &port52 {
        managed = "in-band-status";
 };
@@ -239,26 +81,6 @@
        managed = "in-band-status";
 };
 
-&serdes6 {
-       rx-polarity = <PHY_POL_INVERT>;
-       tx-polarity = <PHY_POL_INVERT>;
-};
-
-&serdes7 {
-       rx-polarity = <PHY_POL_INVERT>;
-       tx-polarity = <PHY_POL_INVERT>;
-};
-
-&serdes8 {
-       rx-polarity = <PHY_POL_INVERT>;
-       tx-polarity = <PHY_POL_INVERT>;
-};
-
-&serdes9 {
-       rx-polarity = <PHY_POL_INVERT>;
-       tx-polarity = <PHY_POL_INVERT>;
-};
-
 &serdes10 {
        tx-polarity = <PHY_POL_INVERT>;
 };
@@ -267,10 +89,3 @@
        tx-polarity = <PHY_POL_INVERT>;
 };
 
-&serdes12 {
-       tx-polarity = <PHY_POL_INVERT>;
-};
-
-&serdes13 {
-       tx-polarity = <PHY_POL_INVERT>;
-};

diff --git a/target/linux/realtek/dts/rtl9313_zyxel_xs1930-aqr813.dtsi b/target/linux/realtek/dts/rtl9313_zyxel_xs1930-aqr813.dtsi
new file mode 100644 (file)
index 0000000..c54f0bd
--- /dev/null
+++ b/target/linux/realtek/dts/rtl9313_zyxel_xs1930-aqr813.dtsi
@@ -0,0 +1,208 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/dts-v1/;
+
+#include "rtl9313_zyxel_xs1930.dtsi"
+
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/mux/mux.h>
+#include <dt-bindings/phy/phy.h>
+
+/ {
+       led_set: led_set@0 {
+               compatible = "realtek,rtl9300-leds";
+               active-low;
+
+               /* Blue | Green | Red */
+               led_set0 = <(RTL93XX_LED_SET_10G | RTL93XX_LED_SET_5G | RTL93XX_LED_SET_2P5G |
+                            RTL93XX_LED_SET_LINK | RTL93XX_LED_SET_ACT)
+                           (RTL93XX_LED_SET_2P5G | RTL93XX_LED_SET_1G | RTL93XX_LED_SET_100M |
+                            RTL93XX_LED_SET_LINK | RTL93XX_LED_SET_ACT)
+                           (RTL93XX_LED_SET_5G | RTL93XX_LED_SET_100M | RTL93XX_LED_SET_LINK |
+                            RTL93XX_LED_SET_ACT)>;
+       };
+
+       sfp_gpio_mux: gpio-mux {
+               compatible = "gpio-mux";
+               mux-gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>,
+                           <&gpio0 14 GPIO_ACTIVE_HIGH>;
+               #mux-control-cells = <0>;
+               idle-state = <MUX_IDLE_AS_IS>;
+       };
+
+       sfp1_gpio: sfp-gpio-1 {
+               compatible = "gpio-line-mux";
+               gpio-controller;
+               #gpio-cells = <2>;
+
+               mux-controls = <&sfp_gpio_mux>;
+               muxed-gpio = <&gpio0 19 GPIO_ACTIVE_HIGH>;
+
+               gpio-line-names = "SFP1_LOS", "SFP1_MOD_ABS", "SFP1_TX_FAULT";
+               gpio-line-mux-states = <0>, <1>, <3>;
+       };
+
+       sfp2_gpio: sfp-gpio-2 {
+               compatible = "gpio-line-mux";
+               gpio-controller;
+               #gpio-cells = <2>;
+
+               mux-controls = <&sfp_gpio_mux>;
+               muxed-gpio = <&gpio0 27 GPIO_ACTIVE_HIGH>;
+
+               gpio-line-names = "SFP2_LOS", "SFP2_MOD_ABS", "SFP2_TX_FAULT";
+               gpio-line-mux-states = <0>, <1>, <3>;
+       };
+
+       sfp1: sfp-p1 {
+               compatible = "sff,sfp";
+               i2c-bus = <&i2c0>;
+               los-gpio = <&sfp1_gpio 0 GPIO_ACTIVE_HIGH>;
+               mod-def0-gpio = <&sfp1_gpio 1 GPIO_ACTIVE_LOW>;
+               tx-disable-gpio = <&gpio0 5 GPIO_ACTIVE_HIGH>;
+               tx-fault-gpio = <&sfp1_gpio 2 GPIO_ACTIVE_HIGH>;
+       };
+
+       sfp2: sfp-p2 {
+               compatible = "sff,sfp";
+               i2c-bus = <&i2c1>;
+               los-gpio = <&sfp2_gpio 0 GPIO_ACTIVE_HIGH>;
+               mod-def0-gpio = <&sfp2_gpio 1 GPIO_ACTIVE_LOW>;
+               tx-disable-gpio = <&gpio0 11 GPIO_ACTIVE_HIGH>;
+               tx-fault-gpio = <&sfp2_gpio 2 GPIO_ACTIVE_HIGH>;
+       };
+};
+
+&gpio0 {
+       pinctrl-names = "default";
+       pinctrl-0 = <&pinmux_disable_jtag>;
+
+       sfp_enable_hog {
+               gpio-hog;
+               gpios = <6 GPIO_ACTIVE_LOW>,
+                       <7 GPIO_ACTIVE_LOW>;
+               output-high;
+               line-name = "sfp-enable";
+       };
+};
+
+&i2c_mst1 {
+       status = "okay";
+
+       i2c0: i2c@0 {
+               reg = <0>;
+       };
+       i2c1: i2c@1 {
+               reg = <1>;
+       };
+
+       i2c2: i2c@2 {
+               reg = <2>;
+
+               lm96000: lm96000@2e {
+                       compatible = "national,lm85";
+                       reg = <0x2e>;
+               };
+       };
+};
+
+&mdio_bus0 {
+       /* AQR813 */
+       PHY_C45(0, 8)
+       PHY_C45(8, 9)
+       PHY_C45(16, 10)
+       PHY_C45(24, 11)
+       PHY_C45(32, 12)
+       PHY_C45(40, 13)
+       PHY_C45(48, 14)
+       PHY_C45(50, 15)
+};
+
+&switch0 {
+       ethernet-ports {
+               #address-cells = <1>;
+               #size-cells = <0>;
+
+               /* Copper ports behind AQR813 */
+               SWITCH_PORT_LED(0, 1, 2, 0, usxgmii)
+               SWITCH_PORT_LED(8, 2, 3, 0, usxgmii)
+               SWITCH_PORT_LED(16, 3, 4, 0, usxgmii)
+               SWITCH_PORT_LED(24, 4, 5, 0, usxgmii)
+               SWITCH_PORT_LED(32, 5, 6, 0, usxgmii)
+               SWITCH_PORT_LED(40, 6, 7, 0, usxgmii)
+               SWITCH_PORT_LED(48, 7, 8, 0, usxgmii)
+               SWITCH_PORT_LED(50, 8, 9, 0, usxgmii)
+
+               /* CPU port */
+               port@56 {
+                       ethernet = <&ethernet0>;
+                       reg = <56>;
+                       phy-mode = "internal";
+                       fixed-link {
+                               speed = <1000>;
+                               full-duplex;
+                       };
+               };
+       };
+};
+
+&port0 {
+       managed = "in-band-status";
+};
+
+&port8 {
+       managed = "in-band-status";
+};
+
+&port16 {
+       managed = "in-band-status";
+};
+
+&port24 {
+       managed = "in-band-status";
+};
+
+&port32 {
+       managed = "in-band-status";
+};
+
+&port40 {
+       managed = "in-band-status";
+};
+
+&port48 {
+       managed = "in-band-status";
+};
+
+&port50 {
+       managed = "in-band-status";
+};
+
+&serdes6 {
+       rx-polarity = <PHY_POL_INVERT>;
+       tx-polarity = <PHY_POL_INVERT>;
+};
+
+&serdes7 {
+       rx-polarity = <PHY_POL_INVERT>;
+       tx-polarity = <PHY_POL_INVERT>;
+};
+
+&serdes8 {
+       rx-polarity = <PHY_POL_INVERT>;
+       tx-polarity = <PHY_POL_INVERT>;
+};
+
+&serdes9 {
+       rx-polarity = <PHY_POL_INVERT>;
+       tx-polarity = <PHY_POL_INVERT>;
+};
+
+&serdes12 {
+       tx-polarity = <PHY_POL_INVERT>;
+};
+
+&serdes13 {
+       tx-polarity = <PHY_POL_INVERT>;
+};