+++ /dev/null
-// SPDX-License-Identifier: GPL-1.0+
-
-/*======================================================================
-
- A PCMCIA ethernet driver for Asix AX88190-based cards
-
- The Asix AX88190 is a NS8390-derived chipset with a few nasty
- idiosyncracies that make it very inconvenient to support with a
- standard 8390 driver. This driver is based on pcnet_cs, with the
- tweaked 8390 code grafted on the end. Much of what I did was to
- clean up and update a similar driver supplied by Asix, which was
- adapted by William Lee, william@asix.com.tw.
-
- Copyright (C) 2001 David A. Hinds -- dahinds@users.sourceforge.net
-
- axnet_cs.c 1.28 2002/06/29 06:27:37
-
- The network driver code is based on Donald Becker's NE2000 code:
-
- Written 1992,1993 by Donald Becker.
- Copyright 1993 United States Government as represented by the
- Director, National Security Agency.
- Donald Becker may be reached at becker@scyld.com
-
-======================================================================*/
-
-#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
-
-#include <linux/kernel.h>
-#include <linux/module.h>
-#include <linux/ptrace.h>
-#include <linux/string.h>
-#include <linux/timer.h>
-#include <linux/delay.h>
-#include <linux/spinlock.h>
-#include <linux/netdevice.h>
-#include <linux/etherdevice.h>
-#include <linux/crc32.h>
-#include <linux/mii.h>
-#include "8390.h"
-
-#include <pcmcia/cistpl.h>
-#include <pcmcia/ciscode.h>
-#include <pcmcia/ds.h>
-#include <pcmcia/cisreg.h>
-
-#include <asm/io.h>
-#include <asm/byteorder.h>
-#include <linux/uaccess.h>
-
-#define AXNET_CMD 0x00
-#define AXNET_DATAPORT 0x10 /* NatSemi-defined port window offset. */
-#define AXNET_RESET 0x1f /* Issue a read to reset, a write to clear. */
-#define AXNET_MII_EEP 0x14 /* Offset of MII access port */
-#define AXNET_TEST 0x15 /* Offset of TEST Register port */
-#define AXNET_GPIO 0x17 /* Offset of General Purpose Register Port */
-
-#define AXNET_START_PG 0x40 /* First page of TX buffer */
-#define AXNET_STOP_PG 0x80 /* Last page +1 of RX ring */
-
-#define AXNET_RDC_TIMEOUT 0x02 /* Max wait in jiffies for Tx RDC */
-
-#define IS_AX88190 0x0001
-#define IS_AX88790 0x0002
-
-/*====================================================================*/
-
-/* Module parameters */
-
-MODULE_AUTHOR("David Hinds <dahinds@users.sourceforge.net>");
-MODULE_DESCRIPTION("Asix AX88190 PCMCIA ethernet driver");
-MODULE_LICENSE("GPL");
-
-
-/*====================================================================*/
-
-static int axnet_config(struct pcmcia_device *link);
-static void axnet_release(struct pcmcia_device *link);
-static int axnet_open(struct net_device *dev);
-static int axnet_close(struct net_device *dev);
-static int axnet_ioctl(struct net_device *dev, struct ifreq *rq, int cmd);
-static netdev_tx_t axnet_start_xmit(struct sk_buff *skb,
- struct net_device *dev);
-static struct net_device_stats *get_stats(struct net_device *dev);
-static void set_multicast_list(struct net_device *dev);
-static void axnet_tx_timeout(struct net_device *dev, unsigned int txqueue);
-static irqreturn_t ei_irq_wrapper(int irq, void *dev_id);
-static void ei_watchdog(struct timer_list *t);
-static void axnet_reset_8390(struct net_device *dev);
-
-static int mdio_read(unsigned int addr, int phy_id, int loc);
-static void mdio_write(unsigned int addr, int phy_id, int loc, int value);
-
-static void get_8390_hdr(struct net_device *,
- struct e8390_pkt_hdr *, int);
-static void block_input(struct net_device *dev, int count,
- struct sk_buff *skb, int ring_offset);
-static void block_output(struct net_device *dev, int count,
- const u_char *buf, const int start_page);
-
-static void axnet_detach(struct pcmcia_device *p_dev);
-
-static void AX88190_init(struct net_device *dev, int startp);
-static int ax_open(struct net_device *dev);
-static int ax_close(struct net_device *dev);
-static irqreturn_t ax_interrupt(int irq, void *dev_id);
-
-/*====================================================================*/
-
-struct axnet_dev {
- struct pcmcia_device *p_dev;
- caddr_t base;
- struct timer_list watchdog;
- int stale, fast_poll;
- u_short link_status;
- u_char duplex_flag;
- int phy_id;
- int flags;
- int active_low;
-};
-
-static inline struct axnet_dev *PRIV(struct net_device *dev)
-{
- void *p = (char *)netdev_priv(dev) + sizeof(struct ei_device);
- return p;
-}
-
-static const struct net_device_ops axnet_netdev_ops = {
- .ndo_open = axnet_open,
- .ndo_stop = axnet_close,
- .ndo_eth_ioctl = axnet_ioctl,
- .ndo_start_xmit = axnet_start_xmit,
- .ndo_tx_timeout = axnet_tx_timeout,
- .ndo_get_stats = get_stats,
- .ndo_set_rx_mode = set_multicast_list,
- .ndo_set_mac_address = eth_mac_addr,
- .ndo_validate_addr = eth_validate_addr,
-};
-
-static int axnet_probe(struct pcmcia_device *link)
-{
- struct axnet_dev *info;
- struct net_device *dev;
- struct ei_device *ei_local;
-
- dev_dbg(&link->dev, "axnet_attach()\n");
-
- dev = alloc_etherdev(sizeof(struct ei_device) + sizeof(struct axnet_dev));
- if (!dev)
- return -ENOMEM;
-
- ei_local = netdev_priv(dev);
- spin_lock_init(&ei_local->page_lock);
-
- info = PRIV(dev);
- info->p_dev = link;
- link->priv = dev;
- link->config_flags |= CONF_ENABLE_IRQ;
-
- dev->netdev_ops = &axnet_netdev_ops;
-
- dev->watchdog_timeo = TX_TIMEOUT;
-
- return axnet_config(link);
-} /* axnet_attach */
-
-static void axnet_detach(struct pcmcia_device *link)
-{
- struct net_device *dev = link->priv;
-
- dev_dbg(&link->dev, "axnet_detach(0x%p)\n", link);
-
- unregister_netdev(dev);
-
- axnet_release(link);
-
- free_netdev(dev);
-} /* axnet_detach */
-
-/*======================================================================
-
- This probes for a card's hardware address by reading the PROM.
-
-======================================================================*/
-
-static int get_prom(struct pcmcia_device *link)
-{
- struct net_device *dev = link->priv;
- unsigned int ioaddr = dev->base_addr;
- u8 addr[ETH_ALEN];
- int i, j;
-
- /* This is based on drivers/net/ethernet/8390/ne.c */
- struct {
- u_char value, offset;
- } program_seq[] = {
- {E8390_NODMA+E8390_PAGE0+E8390_STOP, E8390_CMD}, /* Select page 0*/
- {0x01, EN0_DCFG}, /* Set word-wide access. */
- {0x00, EN0_RCNTLO}, /* Clear the count regs. */
- {0x00, EN0_RCNTHI},
- {0x00, EN0_IMR}, /* Mask completion irq. */
- {0xFF, EN0_ISR},
- {E8390_RXOFF|0x40, EN0_RXCR}, /* 0x60 Set to monitor */
- {E8390_TXOFF, EN0_TXCR}, /* 0x02 and loopback mode. */
- {0x10, EN0_RCNTLO},
- {0x00, EN0_RCNTHI},
- {0x00, EN0_RSARLO}, /* DMA starting at 0x0400. */
- {0x04, EN0_RSARHI},
- {E8390_RREAD+E8390_START, E8390_CMD},
- };
-
- /* Not much of a test, but the alternatives are messy */
- if (link->config_base != 0x03c0)
- return 0;
-
- axnet_reset_8390(dev);
- mdelay(10);
-
- for (i = 0; i < ARRAY_SIZE(program_seq); i++)
- outb_p(program_seq[i].value, ioaddr + program_seq[i].offset);
-
- for (i = 0; i < 6; i += 2) {
- j = inw(ioaddr + AXNET_DATAPORT);
- addr[i] = j & 0xff;
- addr[i+1] = j >> 8;
- }
- eth_hw_addr_set(dev, addr);
-
- return 1;
-} /* get_prom */
-
-static int try_io_port(struct pcmcia_device *link)
-{
- int j, ret;
- link->resource[0]->flags &= ~IO_DATA_PATH_WIDTH;
- link->resource[1]->flags &= ~IO_DATA_PATH_WIDTH;
- if (link->resource[0]->end == 32) {
- link->resource[0]->flags |= IO_DATA_PATH_WIDTH_AUTO;
- /* for master/slave multifunction cards */
- if (link->resource[1]->end > 0)
- link->resource[1]->flags |= IO_DATA_PATH_WIDTH_8;
- } else {
- /* This should be two 16-port windows */
- link->resource[0]->flags |= IO_DATA_PATH_WIDTH_8;
- link->resource[1]->flags |= IO_DATA_PATH_WIDTH_16;
- }
- if (link->resource[0]->start == 0) {
- for (j = 0; j < 0x400; j += 0x20) {
- link->resource[0]->start = j ^ 0x300;
- link->resource[1]->start = (j ^ 0x300) + 0x10;
- link->io_lines = 16;
- ret = pcmcia_request_io(link);
- if (ret == 0)
- return ret;
- }
- return ret;
- } else {
- return pcmcia_request_io(link);
- }
-}
-
-static int axnet_configcheck(struct pcmcia_device *p_dev, void *priv_data)
-{
- if (p_dev->config_index == 0)
- return -EINVAL;
-
- p_dev->config_index = 0x05;
- if (p_dev->resource[0]->end + p_dev->resource[1]->end < 32)
- return -ENODEV;
-
- return try_io_port(p_dev);
-}
-
-static int axnet_config(struct pcmcia_device *link)
-{
- struct net_device *dev = link->priv;
- struct axnet_dev *info = PRIV(dev);
- int i, j, j2, ret;
-
- dev_dbg(&link->dev, "axnet_config(0x%p)\n", link);
-
- /* don't trust the CIS on this; Linksys got it wrong */
- link->config_regs = 0x63;
- link->config_flags |= CONF_ENABLE_IRQ | CONF_AUTO_SET_IO;
- ret = pcmcia_loop_config(link, axnet_configcheck, NULL);
- if (ret != 0)
- goto failed;
-
- if (!link->irq)
- goto failed;
-
- if (resource_size(link->resource[1]) == 8)
- link->config_flags |= CONF_ENABLE_SPKR;
-
- ret = pcmcia_enable_device(link);
- if (ret)
- goto failed;
-
- dev->irq = link->irq;
- dev->base_addr = link->resource[0]->start;
-
- if (!get_prom(link)) {
- pr_notice("this is not an AX88190 card!\n");
- pr_notice("use pcnet_cs instead.\n");
- goto failed;
- }
-
- ei_status.name = "AX88190";
- ei_status.word16 = 1;
- ei_status.tx_start_page = AXNET_START_PG;
- ei_status.rx_start_page = AXNET_START_PG + TX_PAGES;
- ei_status.stop_page = AXNET_STOP_PG;
- ei_status.reset_8390 = axnet_reset_8390;
- ei_status.get_8390_hdr = get_8390_hdr;
- ei_status.block_input = block_input;
- ei_status.block_output = block_output;
-
- if (inb(dev->base_addr + AXNET_TEST) != 0)
- info->flags |= IS_AX88790;
- else
- info->flags |= IS_AX88190;
-
- if (info->flags & IS_AX88790)
- outb(0x10, dev->base_addr + AXNET_GPIO); /* select Internal PHY */
-
- info->active_low = 0;
-
- for (i = 0; i < 32; i++) {
- j = mdio_read(dev->base_addr + AXNET_MII_EEP, i, 1);
- j2 = mdio_read(dev->base_addr + AXNET_MII_EEP, i, 2);
- if (j == j2) continue;
- if ((j != 0) && (j != 0xffff)) break;
- }
-
- if (i == 32) {
- /* Maybe PHY is in power down mode. (PPD_SET = 1)
- Bit 2 of CCSR is active low. */
- pcmcia_write_config_byte(link, CISREG_CCSR, 0x04);
- for (i = 0; i < 32; i++) {
- j = mdio_read(dev->base_addr + AXNET_MII_EEP, i, 1);
- j2 = mdio_read(dev->base_addr + AXNET_MII_EEP, i, 2);
- if (j == j2) continue;
- if ((j != 0) && (j != 0xffff)) {
- info->active_low = 1;
- break;
- }
- }
- }
-
- info->phy_id = (i < 32) ? i : -1;
- SET_NETDEV_DEV(dev, &link->dev);
-
- if (register_netdev(dev) != 0) {
- pr_notice("register_netdev() failed\n");
- goto failed;
- }
-
- netdev_info(dev, "Asix AX88%d90: io %#3lx, irq %d, hw_addr %pM\n",
- ((info->flags & IS_AX88790) ? 7 : 1),
- dev->base_addr, dev->irq, dev->dev_addr);
- if (info->phy_id != -1) {
- netdev_dbg(dev, " MII transceiver at index %d, status %x\n",
- info->phy_id, j);
- } else {
- netdev_notice(dev, " No MII transceivers found!\n");
- }
- return 0;
-
-failed:
- axnet_release(link);
- return -ENODEV;
-} /* axnet_config */
-
-static void axnet_release(struct pcmcia_device *link)
-{
- pcmcia_disable_device(link);
-}
-
-static int axnet_suspend(struct pcmcia_device *link)
-{
- struct net_device *dev = link->priv;
-
- if (link->open)
- netif_device_detach(dev);
-
- return 0;
-}
-
-static int axnet_resume(struct pcmcia_device *link)
-{
- struct net_device *dev = link->priv;
- struct axnet_dev *info = PRIV(dev);
-
- if (link->open) {
- if (info->active_low == 1)
- pcmcia_write_config_byte(link, CISREG_CCSR, 0x04);
-
- axnet_reset_8390(dev);
- AX88190_init(dev, 1);
- netif_device_attach(dev);
- }
-
- return 0;
-}
-
-
-/*======================================================================
-
- MII interface support
-
-======================================================================*/
-
-#define MDIO_SHIFT_CLK 0x01
-#define MDIO_DATA_WRITE0 0x00
-#define MDIO_DATA_WRITE1 0x08
-#define MDIO_DATA_READ 0x04
-#define MDIO_MASK 0x0f
-#define MDIO_ENB_IN 0x02
-
-static void mdio_sync(unsigned int addr)
-{
- int bits;
- for (bits = 0; bits < 32; bits++) {
- outb_p(MDIO_DATA_WRITE1, addr);
- outb_p(MDIO_DATA_WRITE1 | MDIO_SHIFT_CLK, addr);
- }
-}
-
-static int mdio_read(unsigned int addr, int phy_id, int loc)
-{
- u_int cmd = (0xf6<<10)|(phy_id<<5)|loc;
- int i, retval = 0;
-
- mdio_sync(addr);
- for (i = 14; i >= 0; i--) {
- int dat = (cmd&(1<<i)) ? MDIO_DATA_WRITE1 : MDIO_DATA_WRITE0;
- outb_p(dat, addr);
- outb_p(dat | MDIO_SHIFT_CLK, addr);
- }
- for (i = 19; i > 0; i--) {
- outb_p(MDIO_ENB_IN, addr);
- retval = (retval << 1) | ((inb_p(addr) & MDIO_DATA_READ) != 0);
- outb_p(MDIO_ENB_IN | MDIO_SHIFT_CLK, addr);
- }
- return (retval>>1) & 0xffff;
-}
-
-static void mdio_write(unsigned int addr, int phy_id, int loc, int value)
-{
- u_int cmd = (0x05<<28)|(phy_id<<23)|(loc<<18)|(1<<17)|value;
- int i;
-
- mdio_sync(addr);
- for (i = 31; i >= 0; i--) {
- int dat = (cmd&(1<<i)) ? MDIO_DATA_WRITE1 : MDIO_DATA_WRITE0;
- outb_p(dat, addr);
- outb_p(dat | MDIO_SHIFT_CLK, addr);
- }
- for (i = 1; i >= 0; i--) {
- outb_p(MDIO_ENB_IN, addr);
- outb_p(MDIO_ENB_IN | MDIO_SHIFT_CLK, addr);
- }
-}
-
-/*====================================================================*/
-
-static int axnet_open(struct net_device *dev)
-{
- int ret;
- struct axnet_dev *info = PRIV(dev);
- struct pcmcia_device *link = info->p_dev;
- unsigned int nic_base = dev->base_addr;
-
- dev_dbg(&link->dev, "axnet_open('%s')\n", dev->name);
-
- if (!pcmcia_dev_present(link))
- return -ENODEV;
-
- outb_p(0xFF, nic_base + EN0_ISR); /* Clear bogus intr. */
- ret = request_irq(dev->irq, ei_irq_wrapper, IRQF_SHARED, "axnet_cs", dev);
- if (ret)
- return ret;
-
- link->open++;
-
- info->link_status = 0x00;
- timer_setup(&info->watchdog, ei_watchdog, 0);
- mod_timer(&info->watchdog, jiffies + HZ);
-
- return ax_open(dev);
-} /* axnet_open */
-
-/*====================================================================*/
-
-static int axnet_close(struct net_device *dev)
-{
- struct axnet_dev *info = PRIV(dev);
- struct pcmcia_device *link = info->p_dev;
-
- dev_dbg(&link->dev, "axnet_close('%s')\n", dev->name);
-
- ax_close(dev);
- free_irq(dev->irq, dev);
-
- link->open--;
- netif_stop_queue(dev);
- timer_delete_sync(&info->watchdog);
-
- return 0;
-} /* axnet_close */
-
-/*======================================================================
-
- Hard reset the card. This used to pause for the same period that
- a 8390 reset command required, but that shouldn't be necessary.
-
-======================================================================*/
-
-static void axnet_reset_8390(struct net_device *dev)
-{
- unsigned int nic_base = dev->base_addr;
- int i;
-
- ei_status.txing = ei_status.dmaing = 0;
-
- outb_p(E8390_NODMA+E8390_PAGE0+E8390_STOP, nic_base + E8390_CMD);
-
- outb(inb(nic_base + AXNET_RESET), nic_base + AXNET_RESET);
-
- for (i = 0; i < 100; i++) {
- if ((inb_p(nic_base+EN0_ISR) & ENISR_RESET) != 0)
- break;
- udelay(100);
- }
- outb_p(ENISR_RESET, nic_base + EN0_ISR); /* Ack intr. */
-
- if (i == 100)
- netdev_err(dev, "axnet_reset_8390() did not complete\n");
-
-} /* axnet_reset_8390 */
-
-/*====================================================================*/
-
-static irqreturn_t ei_irq_wrapper(int irq, void *dev_id)
-{
- struct net_device *dev = dev_id;
- PRIV(dev)->stale = 0;
- return ax_interrupt(irq, dev_id);
-}
-
-static void ei_watchdog(struct timer_list *t)
-{
- struct axnet_dev *info = timer_container_of(info, t, watchdog);
- struct net_device *dev = info->p_dev->priv;
- unsigned int nic_base = dev->base_addr;
- unsigned int mii_addr = nic_base + AXNET_MII_EEP;
- u_short link;
-
- if (!netif_device_present(dev)) goto reschedule;
-
- /* Check for pending interrupt with expired latency timer: with
- this, we can limp along even if the interrupt is blocked */
- if (info->stale++ && (inb_p(nic_base + EN0_ISR) & ENISR_ALL)) {
- if (!info->fast_poll)
- netdev_info(dev, "interrupt(s) dropped!\n");
- ei_irq_wrapper(dev->irq, dev);
- info->fast_poll = HZ;
- }
- if (info->fast_poll) {
- info->fast_poll--;
- info->watchdog.expires = jiffies + 1;
- add_timer(&info->watchdog);
- return;
- }
-
- if (info->phy_id < 0)
- goto reschedule;
- link = mdio_read(mii_addr, info->phy_id, 1);
- if (!link || (link == 0xffff)) {
- netdev_info(dev, "MII is missing!\n");
- info->phy_id = -1;
- goto reschedule;
- }
-
- link &= 0x0004;
- if (link != info->link_status) {
- u_short p = mdio_read(mii_addr, info->phy_id, 5);
- netdev_info(dev, "%s link beat\n", link ? "found" : "lost");
- if (link) {
- info->duplex_flag = (p & 0x0140) ? 0x80 : 0x00;
- if (p)
- netdev_info(dev, "autonegotiation complete: %dbaseT-%cD selected\n",
- (p & 0x0180) ? 100 : 10, (p & 0x0140) ? 'F' : 'H');
- else
- netdev_info(dev, "link partner did not autonegotiate\n");
- AX88190_init(dev, 1);
- }
- info->link_status = link;
- }
-
-reschedule:
- info->watchdog.expires = jiffies + HZ;
- add_timer(&info->watchdog);
-}
-
-/*====================================================================*/
-
-static int axnet_ioctl(struct net_device *dev, struct ifreq *rq, int cmd)
-{
- struct axnet_dev *info = PRIV(dev);
- struct mii_ioctl_data *data = if_mii(rq);
- unsigned int mii_addr = dev->base_addr + AXNET_MII_EEP;
- switch (cmd) {
- case SIOCGMIIPHY:
- data->phy_id = info->phy_id;
- fallthrough;
- case SIOCGMIIREG: /* Read MII PHY register. */
- data->val_out = mdio_read(mii_addr, data->phy_id, data->reg_num & 0x1f);
- return 0;
- case SIOCSMIIREG: /* Write MII PHY register. */
- mdio_write(mii_addr, data->phy_id, data->reg_num & 0x1f, data->val_in);
- return 0;
- }
- return -EOPNOTSUPP;
-}
-
-/*====================================================================*/
-
-static void get_8390_hdr(struct net_device *dev,
- struct e8390_pkt_hdr *hdr,
- int ring_page)
-{
- unsigned int nic_base = dev->base_addr;
-
- outb_p(0, nic_base + EN0_RSARLO); /* On page boundary */
- outb_p(ring_page, nic_base + EN0_RSARHI);
- outb_p(E8390_RREAD+E8390_START, nic_base + AXNET_CMD);
-
- insw(nic_base + AXNET_DATAPORT, hdr,
- sizeof(struct e8390_pkt_hdr)>>1);
- /* Fix for big endian systems */
- hdr->count = le16_to_cpu(hdr->count);
-
-}
-
-/*====================================================================*/
-
-static void block_input(struct net_device *dev, int count,
- struct sk_buff *skb, int ring_offset)
-{
- unsigned int nic_base = dev->base_addr;
- struct ei_device *ei_local = netdev_priv(dev);
- char *buf = skb->data;
-
- if ((netif_msg_rx_status(ei_local)) && (count != 4))
- netdev_dbg(dev, "[bi=%d]\n", count+4);
- outb_p(ring_offset & 0xff, nic_base + EN0_RSARLO);
- outb_p(ring_offset >> 8, nic_base + EN0_RSARHI);
- outb_p(E8390_RREAD+E8390_START, nic_base + AXNET_CMD);
-
- insw(nic_base + AXNET_DATAPORT,buf,count>>1);
- if (count & 0x01) {
- buf[count-1] = inb(nic_base + AXNET_DATAPORT);
- }
-}
-
-/*====================================================================*/
-
-static void block_output(struct net_device *dev, int count,
- const u_char *buf, const int start_page)
-{
- unsigned int nic_base = dev->base_addr;
-
- pr_debug("%s: [bo=%d]\n", dev->name, count);
-
- /* Round the count up for word writes. Do we need to do this?
- What effect will an odd byte count have on the 8390?
- I should check someday. */
- if (count & 0x01)
- count++;
-
- outb_p(0x00, nic_base + EN0_RSARLO);
- outb_p(start_page, nic_base + EN0_RSARHI);
- outb_p(E8390_RWRITE+E8390_START, nic_base + AXNET_CMD);
- outsw(nic_base + AXNET_DATAPORT, buf, count>>1);
-}
-
-static const struct pcmcia_device_id axnet_ids[] = {
- PCMCIA_PFC_DEVICE_MANF_CARD(0, 0x016c, 0x0081),
- PCMCIA_DEVICE_MANF_CARD(0x018a, 0x0301),
- PCMCIA_DEVICE_MANF_CARD(0x01bf, 0x2328),
- PCMCIA_DEVICE_MANF_CARD(0x026f, 0x0301),
- PCMCIA_DEVICE_MANF_CARD(0x026f, 0x0303),
- PCMCIA_DEVICE_MANF_CARD(0x026f, 0x0309),
- PCMCIA_DEVICE_MANF_CARD(0x0274, 0x1106),
- PCMCIA_DEVICE_MANF_CARD(0x8a01, 0xc1ab),
- PCMCIA_DEVICE_MANF_CARD(0x021b, 0x0202),
- PCMCIA_DEVICE_MANF_CARD(0xffff, 0x1090),
- PCMCIA_DEVICE_PROD_ID12("AmbiCom,Inc.", "Fast Ethernet PC Card(AMB8110)", 0x49b020a7, 0x119cc9fc),
- PCMCIA_DEVICE_PROD_ID124("Fast Ethernet", "16-bit PC Card", "AX88190", 0xb4be14e3, 0x9a12eb6a, 0xab9be5ef),
- PCMCIA_DEVICE_PROD_ID12("ASIX", "AX88190", 0x0959823b, 0xab9be5ef),
- PCMCIA_DEVICE_PROD_ID12("Billionton", "LNA-100B", 0x552ab682, 0xbc3b87e1),
- PCMCIA_DEVICE_PROD_ID12("CHEETAH ETHERCARD", "EN2228", 0x00fa7bc8, 0x00e990cc),
- PCMCIA_DEVICE_PROD_ID12("CNet", "CNF301", 0xbc477dde, 0x78c5f40b),
- PCMCIA_DEVICE_PROD_ID12("corega K.K.", "corega FEther PCC-TXD", 0x5261440f, 0x436768c5),
- PCMCIA_DEVICE_PROD_ID12("corega K.K.", "corega FEtherII PCC-TXD", 0x5261440f, 0x730df72e),
- PCMCIA_DEVICE_PROD_ID12("corega K.K.", "corega FEther PCC-TXM", 0x5261440f, 0x3abbd061),
- PCMCIA_DEVICE_PROD_ID12("Dynalink", "L100C16", 0x55632fd5, 0x66bc2a90),
- PCMCIA_DEVICE_PROD_ID12("IO DATA", "ETXPCM", 0x547e66dc, 0x233adac2),
- PCMCIA_DEVICE_PROD_ID12("Linksys", "EtherFast 10/100 PC Card (PCMPC100 V3)", 0x0733cc81, 0x232019a8),
- PCMCIA_DEVICE_PROD_ID12("MELCO", "LPC3-TX", 0x481e0094, 0xf91af609),
- PCMCIA_DEVICE_PROD_ID12("NETGEAR", "FA411", 0x9aa79dc3, 0x40fad875),
- PCMCIA_DEVICE_PROD_ID12("PCMCIA", "100BASE", 0x281f1c5d, 0x7c2add04),
- PCMCIA_DEVICE_PROD_ID12("PCMCIA", "FastEtherCard", 0x281f1c5d, 0x7ef26116),
- PCMCIA_DEVICE_PROD_ID12("PCMCIA", "FEP501", 0x281f1c5d, 0x2e272058),
- PCMCIA_DEVICE_PROD_ID14("Network Everywhere", "AX88190", 0x820a67b6, 0xab9be5ef),
- PCMCIA_DEVICE_NULL,
-};
-MODULE_DEVICE_TABLE(pcmcia, axnet_ids);
-
-static struct pcmcia_driver axnet_cs_driver = {
- .owner = THIS_MODULE,
- .name = "axnet_cs",
- .probe = axnet_probe,
- .remove = axnet_detach,
- .id_table = axnet_ids,
- .suspend = axnet_suspend,
- .resume = axnet_resume,
-};
-module_pcmcia_driver(axnet_cs_driver);
-
-/*====================================================================*/
-
-/* 8390.c: A general NS8390 ethernet driver core for linux. */
-/*
- Written 1992-94 by Donald Becker.
-
- Copyright 1993 United States Government as represented by the
- Director, National Security Agency.
-
- This software may be used and distributed according to the terms
- of the GNU General Public License, incorporated herein by reference.
-
- The author may be reached as becker@scyld.com, or C/O
- Scyld Computing Corporation
- 410 Severn Ave., Suite 210
- Annapolis MD 21403
-
- This is the chip-specific code for many 8390-based ethernet adaptors.
- This is not a complete driver, it must be combined with board-specific
- code such as ne.c, wd.c, 3c503.c, etc.
-
- Seeing how at least eight drivers use this code, (not counting the
- PCMCIA ones either) it is easy to break some card by what seems like
- a simple innocent change. Please contact me or Donald if you think
- you have found something that needs changing. -- PG
-
- Changelog:
-
- Paul Gortmaker : remove set_bit lock, other cleanups.
- Paul Gortmaker : add ei_get_8390_hdr() so we can pass skb's to
- ei_block_input() for eth_io_copy_and_sum().
- Paul Gortmaker : exchange static int ei_pingpong for a #define,
- also add better Tx error handling.
- Paul Gortmaker : rewrite Rx overrun handling as per NS specs.
- Alexey Kuznetsov : use the 8390's six bit hash multicast filter.
- Paul Gortmaker : tweak ANK's above multicast changes a bit.
- Paul Gortmaker : update packet statistics for v2.1.x
- Alan Cox : support arbitrary stupid port mappings on the
- 68K Macintosh. Support >16bit I/O spaces
- Paul Gortmaker : add kmod support for auto-loading of the 8390
- module by all drivers that require it.
- Alan Cox : Spinlocking work, added 'BUG_83C690'
- Paul Gortmaker : Separate out Tx timeout code from Tx path.
-
- Sources:
- The National Semiconductor LAN Databook, and the 3Com 3c503 databook.
-
- */
-
-#include <linux/bitops.h>
-#include <asm/irq.h>
-#include <linux/fcntl.h>
-#include <linux/in.h>
-#include <linux/interrupt.h>
-
-#define BUG_83C690
-
-/* These are the operational function interfaces to board-specific
- routines.
- void reset_8390(struct net_device *dev)
- Resets the board associated with DEV, including a hardware reset of
- the 8390. This is only called when there is a transmit timeout, and
- it is always followed by 8390_init().
- void block_output(struct net_device *dev, int count, const unsigned char *buf,
- int start_page)
- Write the COUNT bytes of BUF to the packet buffer at START_PAGE. The
- "page" value uses the 8390's 256-byte pages.
- void get_8390_hdr(struct net_device *dev, struct e8390_hdr *hdr, int ring_page)
- Read the 4 byte, page aligned 8390 header. *If* there is a
- subsequent read, it will be of the rest of the packet.
- void block_input(struct net_device *dev, int count, struct sk_buff *skb, int ring_offset)
- Read COUNT bytes from the packet buffer into the skb data area. Start
- reading from RING_OFFSET, the address as the 8390 sees it. This will always
- follow the read of the 8390 header.
-*/
-#define ei_reset_8390 (ei_local->reset_8390)
-#define ei_block_output (ei_local->block_output)
-#define ei_block_input (ei_local->block_input)
-#define ei_get_8390_hdr (ei_local->get_8390_hdr)
-
-/* Index to functions. */
-static void ei_tx_intr(struct net_device *dev);
-static void ei_tx_err(struct net_device *dev);
-static void ei_receive(struct net_device *dev);
-static void ei_rx_overrun(struct net_device *dev);
-
-/* Routines generic to NS8390-based boards. */
-static void NS8390_trigger_send(struct net_device *dev, unsigned int length,
- int start_page);
-static void do_set_multicast_list(struct net_device *dev);
-
-/*
- * SMP and the 8390 setup.
- *
- * The 8390 isn't exactly designed to be multithreaded on RX/TX. There is
- * a page register that controls bank and packet buffer access. We guard
- * this with ei_local->page_lock. Nobody should assume or set the page other
- * than zero when the lock is not held. Lock holders must restore page 0
- * before unlocking. Even pure readers must take the lock to protect in
- * page 0.
- *
- * To make life difficult the chip can also be very slow. We therefore can't
- * just use spinlocks. For the longer lockups we disable the irq the device
- * sits on and hold the lock. We must hold the lock because there is a dual
- * processor case other than interrupts (get stats/set multicast list in
- * parallel with each other and transmit).
- *
- * Note: in theory we can just disable the irq on the card _but_ there is
- * a latency on SMP irq delivery. So we can easily go "disable irq" "sync irqs"
- * enter lock, take the queued irq. So we waddle instead of flying.
- *
- * Finally by special arrangement for the purpose of being generally
- * annoying the transmit function is called bh atomic. That places
- * restrictions on the user context callers as disable_irq won't save
- * them.
- */
-
-/**
- * ax_open - Open/initialize the board.
- * @dev: network device to initialize
- *
- * This routine goes all-out, setting everything
- * up anew at each open, even though many of these registers should only
- * need to be set once at boot.
- */
-static int ax_open(struct net_device *dev)
-{
- unsigned long flags;
- struct ei_device *ei_local = netdev_priv(dev);
-
- /*
- * Grab the page lock so we own the register set, then call
- * the init function.
- */
-
- spin_lock_irqsave(&ei_local->page_lock, flags);
- AX88190_init(dev, 1);
- /* Set the flag before we drop the lock, That way the IRQ arrives
- after its set and we get no silly warnings */
- netif_start_queue(dev);
- spin_unlock_irqrestore(&ei_local->page_lock, flags);
- ei_local->irqlock = 0;
- return 0;
-}
-
-#define dev_lock(dev) (((struct ei_device *)netdev_priv(dev))->page_lock)
-
-/**
- * ax_close - shut down network device
- * @dev: network device to close
- *
- * Opposite of ax_open(). Only used when "ifconfig <devname> down" is done.
- */
-static int ax_close(struct net_device *dev)
-{
- unsigned long flags;
-
- /*
- * Hold the page lock during close
- */
-
- spin_lock_irqsave(&dev_lock(dev), flags);
- AX88190_init(dev, 0);
- spin_unlock_irqrestore(&dev_lock(dev), flags);
- netif_stop_queue(dev);
- return 0;
-}
-
-/**
- * axnet_tx_timeout - handle transmit time out condition
- * @dev: network device which has apparently fallen asleep
- * @txqueue: unused
- *
- * Called by kernel when device never acknowledges a transmit has
- * completed (or failed) - i.e. never posted a Tx related interrupt.
- */
-
-static void axnet_tx_timeout(struct net_device *dev, unsigned int txqueue)
-{
- long e8390_base = dev->base_addr;
- struct ei_device *ei_local = netdev_priv(dev);
- int txsr, isr, tickssofar = jiffies - dev_trans_start(dev);
- unsigned long flags;
-
- dev->stats.tx_errors++;
-
- spin_lock_irqsave(&ei_local->page_lock, flags);
- txsr = inb(e8390_base+EN0_TSR);
- isr = inb(e8390_base+EN0_ISR);
- spin_unlock_irqrestore(&ei_local->page_lock, flags);
-
- netdev_dbg(dev, "Tx timed out, %s TSR=%#2x, ISR=%#2x, t=%d.\n",
- (txsr & ENTSR_ABT) ? "excess collisions." :
- (isr) ? "lost interrupt?" : "cable problem?",
- txsr, isr, tickssofar);
-
- if (!isr && !dev->stats.tx_packets)
- {
- /* The 8390 probably hasn't gotten on the cable yet. */
- ei_local->interface_num ^= 1; /* Try a different xcvr. */
- }
-
- /* Ugly but a reset can be slow, yet must be protected */
-
- spin_lock_irqsave(&ei_local->page_lock, flags);
-
- /* Try to restart the card. Perhaps the user has fixed something. */
- ei_reset_8390(dev);
- AX88190_init(dev, 1);
-
- spin_unlock_irqrestore(&ei_local->page_lock, flags);
- netif_wake_queue(dev);
-}
-
-/**
- * axnet_start_xmit - begin packet transmission
- * @skb: packet to be sent
- * @dev: network device to which packet is sent
- *
- * Sends a packet to an 8390 network device.
- */
-
-static netdev_tx_t axnet_start_xmit(struct sk_buff *skb,
- struct net_device *dev)
-{
- long e8390_base = dev->base_addr;
- struct ei_device *ei_local = netdev_priv(dev);
- int length, send_length, output_page;
- unsigned long flags;
- u8 packet[ETH_ZLEN];
-
- netif_stop_queue(dev);
-
- length = skb->len;
-
- /* Mask interrupts from the ethercard.
- SMP: We have to grab the lock here otherwise the IRQ handler
- on another CPU can flip window and race the IRQ mask set. We end
- up trashing the mcast filter not disabling irqs if we don't lock */
-
- spin_lock_irqsave(&ei_local->page_lock, flags);
- outb_p(0x00, e8390_base + EN0_IMR);
-
- /*
- * Slow phase with lock held.
- */
-
- ei_local->irqlock = 1;
-
- send_length = max(length, ETH_ZLEN);
-
- /*
- * We have two Tx slots available for use. Find the first free
- * slot, and then perform some sanity checks. With two Tx bufs,
- * you get very close to transmitting back-to-back packets. With
- * only one Tx buf, the transmitter sits idle while you reload the
- * card, leaving a substantial gap between each transmitted packet.
- */
-
- if (ei_local->tx1 == 0)
- {
- output_page = ei_local->tx_start_page;
- ei_local->tx1 = send_length;
- if ((netif_msg_tx_queued(ei_local)) &&
- ei_local->tx2 > 0)
- netdev_dbg(dev,
- "idle transmitter tx2=%d, lasttx=%d, txing=%d\n",
- ei_local->tx2, ei_local->lasttx,
- ei_local->txing);
- }
- else if (ei_local->tx2 == 0)
- {
- output_page = ei_local->tx_start_page + TX_PAGES/2;
- ei_local->tx2 = send_length;
- if ((netif_msg_tx_queued(ei_local)) &&
- ei_local->tx1 > 0)
- netdev_dbg(dev,
- "idle transmitter, tx1=%d, lasttx=%d, txing=%d\n",
- ei_local->tx1, ei_local->lasttx,
- ei_local->txing);
- }
- else
- { /* We should never get here. */
- netif_dbg(ei_local, tx_err, dev,
- "No Tx buffers free! tx1=%d tx2=%d last=%d\n",
- ei_local->tx1, ei_local->tx2,
- ei_local->lasttx);
- ei_local->irqlock = 0;
- netif_stop_queue(dev);
- outb_p(ENISR_ALL, e8390_base + EN0_IMR);
- spin_unlock_irqrestore(&ei_local->page_lock, flags);
- dev->stats.tx_errors++;
- return NETDEV_TX_BUSY;
- }
-
- /*
- * Okay, now upload the packet and trigger a send if the transmitter
- * isn't already sending. If it is busy, the interrupt handler will
- * trigger the send later, upon receiving a Tx done interrupt.
- */
-
- if (length == skb->len)
- ei_block_output(dev, length, skb->data, output_page);
- else {
- memset(packet, 0, ETH_ZLEN);
- skb_copy_from_linear_data(skb, packet, skb->len);
- ei_block_output(dev, length, packet, output_page);
- }
-
- if (! ei_local->txing)
- {
- ei_local->txing = 1;
- NS8390_trigger_send(dev, send_length, output_page);
- netif_trans_update(dev);
- if (output_page == ei_local->tx_start_page)
- {
- ei_local->tx1 = -1;
- ei_local->lasttx = -1;
- }
- else
- {
- ei_local->tx2 = -1;
- ei_local->lasttx = -2;
- }
- }
- else ei_local->txqueue++;
-
- if (ei_local->tx1 && ei_local->tx2)
- netif_stop_queue(dev);
- else
- netif_start_queue(dev);
-
- /* Turn 8390 interrupts back on. */
- ei_local->irqlock = 0;
- outb_p(ENISR_ALL, e8390_base + EN0_IMR);
-
- spin_unlock_irqrestore(&ei_local->page_lock, flags);
-
- dev_kfree_skb (skb);
- dev->stats.tx_bytes += send_length;
-
- return NETDEV_TX_OK;
-}
-
-/**
- * ax_interrupt - handle the interrupts from an 8390
- * @irq: interrupt number
- * @dev_id: a pointer to the net_device
- *
- * Handle the ether interface interrupts. We pull packets from
- * the 8390 via the card specific functions and fire them at the networking
- * stack. We also handle transmit completions and wake the transmit path if
- * necessary. We also update the counters and do other housekeeping as
- * needed.
- */
-
-static irqreturn_t ax_interrupt(int irq, void *dev_id)
-{
- struct net_device *dev = dev_id;
- long e8390_base;
- int interrupts, nr_serviced = 0, i;
- struct ei_device *ei_local;
- int handled = 0;
- unsigned long flags;
-
- e8390_base = dev->base_addr;
- ei_local = netdev_priv(dev);
-
- /*
- * Protect the irq test too.
- */
-
- spin_lock_irqsave(&ei_local->page_lock, flags);
-
- if (ei_local->irqlock) {
-#if 1 /* This might just be an interrupt for a PCI device sharing this line */
- const char *msg;
- /* The "irqlock" check is only for testing. */
- if (ei_local->irqlock)
- msg = "Interrupted while interrupts are masked!";
- else
- msg = "Reentering the interrupt handler!";
- netdev_info(dev, "%s, isr=%#2x imr=%#2x\n",
- msg,
- inb_p(e8390_base + EN0_ISR),
- inb_p(e8390_base + EN0_IMR));
-#endif
- spin_unlock_irqrestore(&ei_local->page_lock, flags);
- return IRQ_NONE;
- }
-
- netif_dbg(ei_local, intr, dev, "interrupt(isr=%#2.2x)\n",
- inb_p(e8390_base + EN0_ISR));
-
- outb_p(0x00, e8390_base + EN0_ISR);
- ei_local->irqlock = 1;
-
- /* !!Assumption!! -- we stay in page 0. Don't break this. */
- while ((interrupts = inb_p(e8390_base + EN0_ISR)) != 0 &&
- ++nr_serviced < MAX_SERVICE)
- {
- if (!netif_running(dev) || (interrupts == 0xff)) {
- netif_warn(ei_local, intr, dev,
- "interrupt from stopped card\n");
- outb_p(interrupts, e8390_base + EN0_ISR);
- interrupts = 0;
- break;
- }
- handled = 1;
-
- /* AX88190 bug fix. */
- outb_p(interrupts, e8390_base + EN0_ISR);
- for (i = 0; i < 10; i++) {
- if (!(inb(e8390_base + EN0_ISR) & interrupts))
- break;
- outb_p(0, e8390_base + EN0_ISR);
- outb_p(interrupts, e8390_base + EN0_ISR);
- }
- if (interrupts & ENISR_OVER)
- ei_rx_overrun(dev);
- else if (interrupts & (ENISR_RX+ENISR_RX_ERR))
- {
- /* Got a good (?) packet. */
- ei_receive(dev);
- }
- /* Push the next to-transmit packet through. */
- if (interrupts & ENISR_TX)
- ei_tx_intr(dev);
- else if (interrupts & ENISR_TX_ERR)
- ei_tx_err(dev);
-
- if (interrupts & ENISR_COUNTERS)
- {
- dev->stats.rx_frame_errors += inb_p(e8390_base + EN0_COUNTER0);
- dev->stats.rx_crc_errors += inb_p(e8390_base + EN0_COUNTER1);
- dev->stats.rx_missed_errors+= inb_p(e8390_base + EN0_COUNTER2);
- }
- }
-
- if (interrupts && (netif_msg_intr(ei_local)))
- {
- handled = 1;
- if (nr_serviced >= MAX_SERVICE)
- {
- /* 0xFF is valid for a card removal */
- if (interrupts != 0xFF)
- netdev_warn(dev,
- "Too much work at interrupt, status %#2.2x\n",
- interrupts);
- outb_p(ENISR_ALL, e8390_base + EN0_ISR); /* Ack. most intrs. */
- } else {
- netdev_warn(dev, "unknown interrupt %#2x\n",
- interrupts);
- outb_p(0xff, e8390_base + EN0_ISR); /* Ack. all intrs. */
- }
- }
-
- /* Turn 8390 interrupts back on. */
- ei_local->irqlock = 0;
- outb_p(ENISR_ALL, e8390_base + EN0_IMR);
-
- spin_unlock_irqrestore(&ei_local->page_lock, flags);
- return IRQ_RETVAL(handled);
-}
-
-/**
- * ei_tx_err - handle transmitter error
- * @dev: network device which threw the exception
- *
- * A transmitter error has happened. Most likely excess collisions (which
- * is a fairly normal condition). If the error is one where the Tx will
- * have been aborted, we try and send another one right away, instead of
- * letting the failed packet sit and collect dust in the Tx buffer. This
- * is a much better solution as it avoids kernel based Tx timeouts, and
- * an unnecessary card reset.
- *
- * Called with lock held.
- */
-
-static void ei_tx_err(struct net_device *dev)
-{
- long e8390_base = dev->base_addr;
- unsigned char txsr = inb_p(e8390_base+EN0_TSR);
- unsigned char tx_was_aborted = txsr & (ENTSR_ABT+ENTSR_FU);
-
-#ifdef VERBOSE_ERROR_DUMP
- netdev_dbg(dev, "transmitter error (%#2x):", txsr);
- if (txsr & ENTSR_ABT)
- pr_cont(" excess-collisions");
- if (txsr & ENTSR_ND)
- pr_cont(" non-deferral");
- if (txsr & ENTSR_CRS)
- pr_cont(" lost-carrier");
- if (txsr & ENTSR_FU)
- pr_cont(" FIFO-underrun");
- if (txsr & ENTSR_CDH)
- pr_cont(" lost-heartbeat");
- pr_cont("\n");
-#endif
-
- if (tx_was_aborted)
- ei_tx_intr(dev);
- else
- {
- dev->stats.tx_errors++;
- if (txsr & ENTSR_CRS) dev->stats.tx_carrier_errors++;
- if (txsr & ENTSR_CDH) dev->stats.tx_heartbeat_errors++;
- if (txsr & ENTSR_OWC) dev->stats.tx_window_errors++;
- }
-}
-
-/**
- * ei_tx_intr - transmit interrupt handler
- * @dev: network device for which tx intr is handled
- *
- * We have finished a transmit: check for errors and then trigger the next
- * packet to be sent. Called with lock held.
- */
-
-static void ei_tx_intr(struct net_device *dev)
-{
- long e8390_base = dev->base_addr;
- struct ei_device *ei_local = netdev_priv(dev);
- int status = inb(e8390_base + EN0_TSR);
-
- /*
- * There are two Tx buffers, see which one finished, and trigger
- * the send of another one if it exists.
- */
- ei_local->txqueue--;
-
- if (ei_local->tx1 < 0)
- {
- if (ei_local->lasttx != 1 && ei_local->lasttx != -1)
- netdev_err(dev, "%s: bogus last_tx_buffer %d, tx1=%d\n",
- ei_local->name, ei_local->lasttx,
- ei_local->tx1);
- ei_local->tx1 = 0;
- if (ei_local->tx2 > 0)
- {
- ei_local->txing = 1;
- NS8390_trigger_send(dev, ei_local->tx2, ei_local->tx_start_page + 6);
- netif_trans_update(dev);
- ei_local->tx2 = -1;
- ei_local->lasttx = 2;
- } else {
- ei_local->lasttx = 20;
- ei_local->txing = 0;
- }
- }
- else if (ei_local->tx2 < 0)
- {
- if (ei_local->lasttx != 2 && ei_local->lasttx != -2)
- netdev_err(dev, "%s: bogus last_tx_buffer %d, tx2=%d\n",
- ei_local->name, ei_local->lasttx,
- ei_local->tx2);
- ei_local->tx2 = 0;
- if (ei_local->tx1 > 0)
- {
- ei_local->txing = 1;
- NS8390_trigger_send(dev, ei_local->tx1, ei_local->tx_start_page);
- netif_trans_update(dev);
- ei_local->tx1 = -1;
- ei_local->lasttx = 1;
- } else {
- ei_local->lasttx = 10;
- ei_local->txing = 0;
- }
- }
-// else
-// netdev_warn(dev, "unexpected TX-done interrupt, lasttx=%d\n",
-// ei_local->lasttx);
-
- /* Minimize Tx latency: update the statistics after we restart TXing. */
- if (status & ENTSR_COL)
- dev->stats.collisions++;
- if (status & ENTSR_PTX)
- dev->stats.tx_packets++;
- else
- {
- dev->stats.tx_errors++;
- if (status & ENTSR_ABT)
- {
- dev->stats.tx_aborted_errors++;
- dev->stats.collisions += 16;
- }
- if (status & ENTSR_CRS)
- dev->stats.tx_carrier_errors++;
- if (status & ENTSR_FU)
- dev->stats.tx_fifo_errors++;
- if (status & ENTSR_CDH)
- dev->stats.tx_heartbeat_errors++;
- if (status & ENTSR_OWC)
- dev->stats.tx_window_errors++;
- }
- netif_wake_queue(dev);
-}
-
-/**
- * ei_receive - receive some packets
- * @dev: network device with which receive will be run
- *
- * We have a good packet(s), get it/them out of the buffers.
- * Called with lock held.
- */
-
-static void ei_receive(struct net_device *dev)
-{
- long e8390_base = dev->base_addr;
- struct ei_device *ei_local = netdev_priv(dev);
- unsigned char rxing_page, this_frame, next_frame;
- unsigned short current_offset;
- int rx_pkt_count = 0;
- struct e8390_pkt_hdr rx_frame;
-
- while (++rx_pkt_count < 10)
- {
- int pkt_len, pkt_stat;
-
- /* Get the rx page (incoming packet pointer). */
- rxing_page = inb_p(e8390_base + EN1_CURPAG -1);
-
- /* Remove one frame from the ring. Boundary is always a page behind. */
- this_frame = inb_p(e8390_base + EN0_BOUNDARY) + 1;
- if (this_frame >= ei_local->stop_page)
- this_frame = ei_local->rx_start_page;
-
- /* Someday we'll omit the previous, iff we never get this message.
- (There is at least one clone claimed to have a problem.)
-
- Keep quiet if it looks like a card removal. One problem here
- is that some clones crash in roughly the same way.
- */
- if ((netif_msg_rx_err(ei_local)) &&
- this_frame != ei_local->current_page &&
- (this_frame != 0x0 || rxing_page != 0xFF))
- netdev_err(dev, "mismatched read page pointers %2x vs %2x\n",
- this_frame, ei_local->current_page);
-
- if (this_frame == rxing_page) /* Read all the frames? */
- break; /* Done for now */
-
- current_offset = this_frame << 8;
- ei_get_8390_hdr(dev, &rx_frame, this_frame);
-
- pkt_len = rx_frame.count - sizeof(struct e8390_pkt_hdr);
- pkt_stat = rx_frame.status;
-
- next_frame = this_frame + 1 + ((pkt_len+4)>>8);
-
- if (pkt_len < 60 || pkt_len > 1518)
- {
- netif_err(ei_local, rx_err, dev,
- "bogus packet size: %d, status=%#2x nxpg=%#2x\n",
- rx_frame.count, rx_frame.status,
- rx_frame.next);
- dev->stats.rx_errors++;
- dev->stats.rx_length_errors++;
- }
- else if ((pkt_stat & 0x0F) == ENRSR_RXOK)
- {
- struct sk_buff *skb;
-
- skb = netdev_alloc_skb(dev, pkt_len + 2);
- if (skb == NULL)
- {
- netif_err(ei_local, rx_err, dev,
- "Couldn't allocate a sk_buff of size %d\n",
- pkt_len);
- dev->stats.rx_dropped++;
- break;
- }
- else
- {
- skb_reserve(skb,2); /* IP headers on 16 byte boundaries */
- skb_put(skb, pkt_len); /* Make room */
- ei_block_input(dev, pkt_len, skb, current_offset + sizeof(rx_frame));
- skb->protocol=eth_type_trans(skb,dev);
- netif_rx(skb);
- dev->stats.rx_packets++;
- dev->stats.rx_bytes += pkt_len;
- if (pkt_stat & ENRSR_PHY)
- dev->stats.multicast++;
- }
- }
- else
- {
- netif_err(ei_local, rx_err, dev,
- "bogus packet: status=%#2x nxpg=%#2x size=%d\n",
- rx_frame.status, rx_frame.next,
- rx_frame.count);
- dev->stats.rx_errors++;
- /* NB: The NIC counts CRC, frame and missed errors. */
- if (pkt_stat & ENRSR_FO)
- dev->stats.rx_fifo_errors++;
- }
- next_frame = rx_frame.next;
-
- /* This _should_ never happen: it's here for avoiding bad clones. */
- if (next_frame >= ei_local->stop_page) {
- netdev_info(dev, "next frame inconsistency, %#2x\n",
- next_frame);
- next_frame = ei_local->rx_start_page;
- }
- ei_local->current_page = next_frame;
- outb_p(next_frame-1, e8390_base+EN0_BOUNDARY);
- }
-}
-
-/**
- * ei_rx_overrun - handle receiver overrun
- * @dev: network device which threw exception
- *
- * We have a receiver overrun: we have to kick the 8390 to get it started
- * again. Problem is that you have to kick it exactly as NS prescribes in
- * the updated datasheets, or "the NIC may act in an unpredictable manner."
- * This includes causing "the NIC to defer indefinitely when it is stopped
- * on a busy network." Ugh.
- * Called with lock held. Don't call this with the interrupts off or your
- * computer will hate you - it takes 10ms or so.
- */
-
-static void ei_rx_overrun(struct net_device *dev)
-{
- struct axnet_dev *info = PRIV(dev);
- long e8390_base = dev->base_addr;
- unsigned char was_txing, must_resend = 0;
- struct ei_device *ei_local = netdev_priv(dev);
-
- /*
- * Record whether a Tx was in progress and then issue the
- * stop command.
- */
- was_txing = inb_p(e8390_base+E8390_CMD) & E8390_TRANS;
- outb_p(E8390_NODMA+E8390_PAGE0+E8390_STOP, e8390_base+E8390_CMD);
-
- netif_dbg(ei_local, rx_err, dev, "Receiver overrun\n");
- dev->stats.rx_over_errors++;
-
- /*
- * Wait a full Tx time (1.2ms) + some guard time, NS says 1.6ms total.
- * We wait at least 2ms.
- */
-
- mdelay(2);
-
- /*
- * Reset RBCR[01] back to zero as per magic incantation.
- */
- outb_p(0x00, e8390_base+EN0_RCNTLO);
- outb_p(0x00, e8390_base+EN0_RCNTHI);
-
- /*
- * See if any Tx was interrupted or not. According to NS, this
- * step is vital, and skipping it will cause no end of havoc.
- */
-
- if (was_txing)
- {
- unsigned char tx_completed = inb_p(e8390_base+EN0_ISR) & (ENISR_TX+ENISR_TX_ERR);
- if (!tx_completed)
- must_resend = 1;
- }
-
- /*
- * Have to enter loopback mode and then restart the NIC before
- * you are allowed to slurp packets up off the ring.
- */
- outb_p(E8390_TXOFF, e8390_base + EN0_TXCR);
- outb_p(E8390_NODMA + E8390_PAGE0 + E8390_START, e8390_base + E8390_CMD);
-
- /*
- * Clear the Rx ring of all the debris, and ack the interrupt.
- */
- ei_receive(dev);
-
- /*
- * Leave loopback mode, and resend any packet that got stopped.
- */
- outb_p(E8390_TXCONFIG | info->duplex_flag, e8390_base + EN0_TXCR);
- if (must_resend)
- outb_p(E8390_NODMA + E8390_PAGE0 + E8390_START + E8390_TRANS, e8390_base + E8390_CMD);
-}
-
-/*
- * Collect the stats. This is called unlocked and from several contexts.
- */
-
-static struct net_device_stats *get_stats(struct net_device *dev)
-{
- long ioaddr = dev->base_addr;
- struct ei_device *ei_local = netdev_priv(dev);
- unsigned long flags;
-
- /* If the card is stopped, just return the present stats. */
- if (!netif_running(dev))
- return &dev->stats;
-
- spin_lock_irqsave(&ei_local->page_lock,flags);
- /* Read the counter registers, assuming we are in page 0. */
- dev->stats.rx_frame_errors += inb_p(ioaddr + EN0_COUNTER0);
- dev->stats.rx_crc_errors += inb_p(ioaddr + EN0_COUNTER1);
- dev->stats.rx_missed_errors+= inb_p(ioaddr + EN0_COUNTER2);
- spin_unlock_irqrestore(&ei_local->page_lock, flags);
-
- return &dev->stats;
-}
-
-/*
- * Form the 64 bit 8390 multicast table from the linked list of addresses
- * associated with this dev structure.
- */
-
-static inline void make_mc_bits(u8 *bits, struct net_device *dev)
-{
- struct netdev_hw_addr *ha;
- u32 crc;
-
- netdev_for_each_mc_addr(ha, dev) {
- crc = ether_crc(ETH_ALEN, ha->addr);
- /*
- * The 8390 uses the 6 most significant bits of the
- * CRC to index the multicast table.
- */
- bits[crc>>29] |= (1<<((crc>>26)&7));
- }
-}
-
-/**
- * do_set_multicast_list - set/clear multicast filter
- * @dev: net device for which multicast filter is adjusted
- *
- * Set or clear the multicast filter for this adaptor.
- * Must be called with lock held.
- */
-
-static void do_set_multicast_list(struct net_device *dev)
-{
- long e8390_base = dev->base_addr;
- int i;
- struct ei_device *ei_local = netdev_priv(dev);
-
- if (!(dev->flags&(IFF_PROMISC|IFF_ALLMULTI))) {
- memset(ei_local->mcfilter, 0, 8);
- if (!netdev_mc_empty(dev))
- make_mc_bits(ei_local->mcfilter, dev);
- } else {
- /* set to accept-all */
- memset(ei_local->mcfilter, 0xFF, 8);
- }
-
- outb_p(E8390_NODMA + E8390_PAGE1, e8390_base + E8390_CMD);
- for(i = 0; i < 8; i++)
- {
- outb_p(ei_local->mcfilter[i], e8390_base + EN1_MULT_SHIFT(i));
- }
- outb_p(E8390_NODMA + E8390_PAGE0, e8390_base + E8390_CMD);
-
- if(dev->flags&IFF_PROMISC)
- outb_p(E8390_RXCONFIG | 0x58, e8390_base + EN0_RXCR);
- else if (dev->flags & IFF_ALLMULTI || !netdev_mc_empty(dev))
- outb_p(E8390_RXCONFIG | 0x48, e8390_base + EN0_RXCR);
- else
- outb_p(E8390_RXCONFIG | 0x40, e8390_base + EN0_RXCR);
-
- outb_p(E8390_NODMA+E8390_PAGE0+E8390_START, e8390_base+E8390_CMD);
-}
-
-/*
- * Called without lock held. This is invoked from user context and may
- * be parallel to just about everything else. Its also fairly quick and
- * not called too often. Must protect against both bh and irq users
- */
-
-static void set_multicast_list(struct net_device *dev)
-{
- unsigned long flags;
-
- spin_lock_irqsave(&dev_lock(dev), flags);
- do_set_multicast_list(dev);
- spin_unlock_irqrestore(&dev_lock(dev), flags);
-}
-
-/* This page of functions should be 8390 generic */
-/* Follow National Semi's recommendations for initializing the "NIC". */
-
-/**
- * AX88190_init - initialize 8390 hardware
- * @dev: network device to initialize
- * @startp: boolean. non-zero value to initiate chip processing
- *
- * Must be called with lock held.
- */
-
-static void AX88190_init(struct net_device *dev, int startp)
-{
- struct axnet_dev *info = PRIV(dev);
- long e8390_base = dev->base_addr;
- struct ei_device *ei_local = netdev_priv(dev);
- int i;
- int endcfg = ei_local->word16 ? (0x48 | ENDCFG_WTS) : 0x48;
-
- if(sizeof(struct e8390_pkt_hdr)!=4)
- panic("8390.c: header struct mispacked\n");
- /* Follow National Semi's recommendations for initing the DP83902. */
- outb_p(E8390_NODMA+E8390_PAGE0+E8390_STOP, e8390_base+E8390_CMD); /* 0x21 */
- outb_p(endcfg, e8390_base + EN0_DCFG); /* 0x48 or 0x49 */
- /* Clear the remote byte count registers. */
- outb_p(0x00, e8390_base + EN0_RCNTLO);
- outb_p(0x00, e8390_base + EN0_RCNTHI);
- /* Set to monitor and loopback mode -- this is vital!. */
- outb_p(E8390_RXOFF|0x40, e8390_base + EN0_RXCR); /* 0x60 */
- outb_p(E8390_TXOFF, e8390_base + EN0_TXCR); /* 0x02 */
- /* Set the transmit page and receive ring. */
- outb_p(ei_local->tx_start_page, e8390_base + EN0_TPSR);
- ei_local->tx1 = ei_local->tx2 = 0;
- outb_p(ei_local->rx_start_page, e8390_base + EN0_STARTPG);
- outb_p(ei_local->stop_page-1, e8390_base + EN0_BOUNDARY); /* 3c503 says 0x3f,NS0x26*/
- ei_local->current_page = ei_local->rx_start_page; /* assert boundary+1 */
- outb_p(ei_local->stop_page, e8390_base + EN0_STOPPG);
- /* Clear the pending interrupts and mask. */
- outb_p(0xFF, e8390_base + EN0_ISR);
- outb_p(0x00, e8390_base + EN0_IMR);
-
- /* Copy the station address into the DS8390 registers. */
-
- outb_p(E8390_NODMA + E8390_PAGE1 + E8390_STOP, e8390_base+E8390_CMD); /* 0x61 */
- for(i = 0; i < 6; i++)
- {
- outb_p(dev->dev_addr[i], e8390_base + EN1_PHYS_SHIFT(i));
- if(inb_p(e8390_base + EN1_PHYS_SHIFT(i))!=dev->dev_addr[i])
- netdev_err(dev, "Hw. address read/write mismap %d\n", i);
- }
-
- outb_p(ei_local->rx_start_page, e8390_base + EN1_CURPAG);
- outb_p(E8390_NODMA+E8390_PAGE0+E8390_STOP, e8390_base+E8390_CMD);
-
- netif_start_queue(dev);
- ei_local->tx1 = ei_local->tx2 = 0;
- ei_local->txing = 0;
-
- if (info->flags & IS_AX88790) /* select Internal PHY */
- outb(0x10, e8390_base + AXNET_GPIO);
-
- if (startp)
- {
- outb_p(0xff, e8390_base + EN0_ISR);
- outb_p(ENISR_ALL, e8390_base + EN0_IMR);
- outb_p(E8390_NODMA+E8390_PAGE0+E8390_START, e8390_base+E8390_CMD);
- outb_p(E8390_TXCONFIG | info->duplex_flag,
- e8390_base + EN0_TXCR); /* xmit on. */
- /* 3c503 TechMan says rxconfig only after the NIC is started. */
- outb_p(E8390_RXCONFIG | 0x40, e8390_base + EN0_RXCR); /* rx on, */
- do_set_multicast_list(dev); /* (re)load the mcast table */
- }
-}
-
-/* Trigger a transmit start, assuming the length is valid.
- Always called with the page lock held */
-
-static void NS8390_trigger_send(struct net_device *dev, unsigned int length,
- int start_page)
-{
- long e8390_base = dev->base_addr;
- struct ei_device *ei_local __attribute((unused)) = netdev_priv(dev);
-
- if (inb_p(e8390_base) & E8390_TRANS)
- {
- netdev_warn(dev, "trigger_send() called with the transmitter busy\n");
- return;
- }
- outb_p(length & 0xff, e8390_base + EN0_TCNTLO);
- outb_p(length >> 8, e8390_base + EN0_TCNTHI);
- outb_p(start_page, e8390_base + EN0_TPSR);
- outb_p(E8390_NODMA+E8390_TRANS+E8390_START, e8390_base+E8390_CMD);
-}
projects / thirdparty / kernel / linux.git / commitdiff
