dtb-$(CONFIG_ARCH_QCOM) += apq8039-t2.dtb
dtb-$(CONFIG_ARCH_QCOM) += apq8094-sony-xperia-kitakami-karin_windy.dtb
dtb-$(CONFIG_ARCH_QCOM) += apq8096-db820c.dtb
+dtb-$(CONFIG_ARCH_QCOM) += apq8096sg-db820c.dtb
dtb-$(CONFIG_ARCH_QCOM) += apq8096-ifc6640.dtb
dtb-$(CONFIG_ARCH_QCOM) += glymur-crd.dtb
dtb-$(CONFIG_ARCH_QCOM) += hamoa-iot-evk.dtb
/dts-v1/;
#include "msm8996.dtsi"
-#include "pm8994.dtsi"
-#include "pmi8994.dtsi"
-#include <dt-bindings/input/input.h>
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/leds/common.h>
-#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
-#include <dt-bindings/sound/qcom,q6afe.h>
-#include <dt-bindings/sound/qcom,q6asm.h>
-#include <dt-bindings/sound/qcom,wcd9335.h>
-
-/*
- * GPIO name legend: proper name = the GPIO line is used as GPIO
- * NC = not connected (pin out but not routed from the chip to
- * anything the board)
- * "[PER]" = pin is muxed for [peripheral] (not GPIO)
- * LSEC = Low Speed External Connector
- * P HSEC = Primary High Speed External Connector
- * S HSEC = Secondary High Speed External Connector
- * J14 = Camera Connector
- * TP = Test Points
- *
- * Line names are taken from the schematic "DragonBoard 820c",
- * drawing no: LM25-P2751-1
- *
- * For the lines routed to the external connectors the
- * lines are named after the 96Boards CE Specification 1.0,
- * Appendix "Expansion Connector Signal Description".
- *
- * When the 96Board naming of a line and the schematic name of
- * the same line are in conflict, the 96Board specification
- * takes precedence, which means that the external UART on the
- * LSEC is named UART0 while the schematic and SoC names this
- * UART3. This is only for the informational lines i.e. "[FOO]",
- * the GPIO named lines "GPIO-A" thru "GPIO-L" are the only
- * ones actually used for GPIO.
- */
+#include "apq8096-db820c.dtsi"
/ {
model = "Qualcomm Technologies, Inc. DB820c";
compatible = "arrow,apq8096-db820c", "qcom,apq8096-sbc", "qcom,apq8096";
-
- aliases {
- serial0 = &blsp2_uart2;
- serial1 = &blsp2_uart3;
- serial2 = &blsp1_uart2;
- i2c0 = &blsp1_i2c3;
- i2c1 = &blsp2_i2c1;
- i2c2 = &blsp2_i2c1;
- spi0 = &blsp1_spi1;
- spi1 = &blsp2_spi6;
- };
-
- chosen {
- stdout-path = "serial0:115200n8";
- };
-
- div1_mclk: divclk1 {
- compatible = "gpio-gate-clock";
- pinctrl-0 = <&audio_mclk>;
- pinctrl-names = "default";
- clocks = <&rpmcc RPM_SMD_DIV_CLK1>;
- #clock-cells = <0>;
- enable-gpios = <&pm8994_gpios 15 0>;
- };
-
- divclk4: divclk4 {
- compatible = "fixed-clock";
- #clock-cells = <0>;
- clock-frequency = <32768>;
- clock-output-names = "divclk4";
-
- pinctrl-names = "default";
- pinctrl-0 = <&divclk4_pin_a>;
- };
-
- gpio-keys {
- compatible = "gpio-keys";
- autorepeat;
-
- pinctrl-names = "default";
- pinctrl-0 = <&volume_up_gpio>;
-
- button {
- label = "Volume Up";
- linux,code = <KEY_VOLUMEUP>;
- gpios = <&pm8994_gpios 2 GPIO_ACTIVE_LOW>;
- };
- };
-
- usb2_id: usb2-id {
- compatible = "linux,extcon-usb-gpio";
- id-gpios = <&pmi8994_gpios 6 GPIO_ACTIVE_HIGH>;
- pinctrl-names = "default";
- pinctrl-0 = <&usb2_vbus_det_gpio>;
- };
-
- usb3_id: usb3-id {
- compatible = "linux,extcon-usb-gpio";
- id-gpios = <&pm8994_gpios 22 GPIO_ACTIVE_HIGH>;
- pinctrl-names = "default";
- pinctrl-0 = <&usb3_vbus_det_gpio>;
- };
-
- vph_pwr: vph-pwr-regulator {
- compatible = "regulator-fixed";
- regulator-name = "vph_pwr";
- regulator-always-on;
- regulator-boot-on;
-
- regulator-min-microvolt = <3700000>;
- regulator-max-microvolt = <3700000>;
- };
-
- wlan_en: wlan-en-1-8v {
- pinctrl-names = "default";
- pinctrl-0 = <&wlan_en_gpios>;
- compatible = "regulator-fixed";
- regulator-name = "wlan-en-regulator";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
-
- gpio = <&pm8994_gpios 8 0>;
-
- /* WLAN card specific delay */
- startup-delay-us = <70000>;
- enable-active-high;
- };
-};
-
-&blsp1_i2c3 {
- /* On Low speed expansion: LS-I2C0 */
- status = "okay";
-};
-
-&blsp1_spi1 {
- /* On Low speed expansion */
- status = "okay";
-};
-
-&blsp1_uart2 {
- label = "BT-UART";
- status = "okay";
-
- bluetooth {
- compatible = "qcom,qca6174-bt";
-
- /* bt_disable_n gpio */
- enable-gpios = <&pm8994_gpios 19 GPIO_ACTIVE_HIGH>;
-
- clocks = <&divclk4>;
- };
-};
-
-&adsp_pil {
- status = "okay";
- firmware-name = "qcom/apq8096/adsp.mbn";
-};
-
-&blsp2_i2c1 {
- /* On High speed expansion: HS-I2C2 */
- status = "okay";
-};
-
-&blsp2_i2c1 {
- /* On Low speed expansion: LS-I2C1 */
- status = "okay";
-};
-
-&blsp2_spi6 {
- /* On High speed expansion */
- status = "okay";
-};
-
-&blsp2_uart2 {
- label = "LS-UART1";
- status = "okay";
- pinctrl-names = "default", "sleep";
- pinctrl-0 = <&blsp2_uart2_2pins_default>;
- pinctrl-1 = <&blsp2_uart2_2pins_sleep>;
-};
-
-&blsp2_uart3 {
- label = "LS-UART0";
- status = "disabled";
- pinctrl-names = "default", "sleep";
- pinctrl-0 = <&blsp2_uart3_4pins_default>;
- pinctrl-1 = <&blsp2_uart3_4pins_sleep>;
-};
-
-&camss {
- vdda-supply = <&vreg_l2a_1p25>;
-};
-
-&gpu {
- status = "okay";
-};
-
-&gpu_zap_shader {
- firmware-name = "qcom/apq8096/a530_zap.mbn";
-};
-
-&hsusb_phy1 {
- status = "okay";
-
- vdd-supply = <&vreg_l28a_0p925>;
- vdda-pll-supply = <&vreg_l12a_1p8>;
- vdda-phy-dpdm-supply = <&vreg_l24a_3p075>;
-};
-
-&hsusb_phy2 {
- status = "okay";
-
- vdd-supply = <&vreg_l28a_0p925>;
- vdda-pll-supply = <&vreg_l12a_1p8>;
- vdda-phy-dpdm-supply = <&vreg_l24a_3p075>;
-};
-
-&mdp {
- status = "okay";
-};
-
-&mdss {
- status = "okay";
-};
-
-&mdss_hdmi {
- status = "okay";
-
- pinctrl-names = "default", "sleep";
- pinctrl-0 = <&hdmi_hpd_active &hdmi_ddc_active>;
- pinctrl-1 = <&hdmi_hpd_suspend &hdmi_ddc_suspend>;
-
- core-vdda-supply = <&vreg_l12a_1p8>;
- core-vcc-supply = <&vreg_s4a_1p8>;
-};
-
-&mdss_hdmi_phy {
- status = "okay";
-
- vddio-supply = <&vreg_l12a_1p8>;
- vcca-supply = <&vreg_l28a_0p925>;
- #phy-cells = <0>;
-};
-
-&mmcc {
- vdd-gfx-supply = <&vdd_gfx>;
-};
-
-&mss_pil {
- status = "okay";
- pll-supply = <&vreg_l12a_1p8>;
- firmware-name = "qcom/apq8096/mba.mbn", "qcom/apq8096/modem.mbn";
-};
-
-&pm8994_resin {
- status = "okay";
- linux,code = <KEY_VOLUMEDOWN>;
-};
-
-&tlmm {
- gpio-line-names =
- "[SPI0_DOUT]", /* GPIO_0, BLSP1_SPI_MOSI, LSEC pin 14 */
- "[SPI0_DIN]", /* GPIO_1, BLSP1_SPI_MISO, LSEC pin 10 */
- "[SPI0_CS]", /* GPIO_2, BLSP1_SPI_CS_N, LSEC pin 12 */
- "[SPI0_SCLK]", /* GPIO_3, BLSP1_SPI_CLK, LSEC pin 8 */
- "[UART1_TxD]", /* GPIO_4, BLSP8_UART_TX, LSEC pin 11 */
- "[UART1_RxD]", /* GPIO_5, BLSP8_UART_RX, LSEC pin 13 */
- "[I2C1_SDA]", /* GPIO_6, BLSP8_I2C_SDA, LSEC pin 21 */
- "[I2C1_SCL]", /* GPIO_7, BLSP8_I2C_SCL, LSEC pin 19 */
- "GPIO-H", /* GPIO_8, LCD0_RESET_N, LSEC pin 30 */
- "TP93", /* GPIO_9 */
- "GPIO-G", /* GPIO_10, MDP_VSYNC_P, LSEC pin 29 */
- "[MDP_VSYNC_S]", /* GPIO_11, S HSEC pin 55 */
- "NC", /* GPIO_12 */
- "[CSI0_MCLK]", /* GPIO_13, CAM_MCLK0, P HSEC pin 15 */
- "[CAM_MCLK1]", /* GPIO_14, J14 pin 11 */
- "[CSI1_MCLK]", /* GPIO_15, CAM_MCLK2, P HSEC pin 17 */
- "TP99", /* GPIO_16 */
- "[I2C2_SDA]", /* GPIO_17, CCI_I2C_SDA0, P HSEC pin 34 */
- "[I2C2_SCL]", /* GPIO_18, CCI_I2C_SCL0, P HSEC pin 32 */
- "[CCI_I2C_SDA1]", /* GPIO_19, S HSEC pin 38 */
- "[CCI_I2C_SCL1]", /* GPIO_20, S HSEC pin 36 */
- "FLASH_STROBE_EN", /* GPIO_21, S HSEC pin 5 */
- "FLASH_STROBE_TRIG", /* GPIO_22, S HSEC pin 1 */
- "GPIO-K", /* GPIO_23, CAM2_RST_N, LSEC pin 33 */
- "GPIO-D", /* GPIO_24, LSEC pin 26 */
- "GPIO-I", /* GPIO_25, CAM0_RST_N, LSEC pin 31 */
- "GPIO-J", /* GPIO_26, CAM0_STANDBY_N, LSEC pin 32 */
- "BLSP6_I2C_SDA", /* GPIO_27 */
- "BLSP6_I2C_SCL", /* GPIO_28 */
- "GPIO-B", /* GPIO_29, TS0_RESET_N, LSEC pin 24 */
- "GPIO30", /* GPIO_30, S HSEC pin 4 */
- "HDMI_CEC", /* GPIO_31 */
- "HDMI_DDC_CLOCK", /* GPIO_32 */
- "HDMI_DDC_DATA", /* GPIO_33 */
- "HDMI_HOT_PLUG_DETECT", /* GPIO_34 */
- "PCIE0_RST_N", /* GPIO_35 */
- "PCIE0_CLKREQ_N", /* GPIO_36 */
- "PCIE0_WAKE", /* GPIO_37 */
- "SD_CARD_DET_N", /* GPIO_38 */
- "TSIF1_SYNC", /* GPIO_39, S HSEC pin 48 */
- "W_DISABLE_N", /* GPIO_40 */
- "[BLSP9_UART_TX]", /* GPIO_41 */
- "[BLSP9_UART_RX]", /* GPIO_42 */
- "[BLSP2_UART_CTS_N]", /* GPIO_43 */
- "[BLSP2_UART_RFR_N]", /* GPIO_44 */
- "[BLSP3_UART_TX]", /* GPIO_45 */
- "[BLSP3_UART_RX]", /* GPIO_46 */
- "[I2C0_SDA]", /* GPIO_47, LS_I2C0_SDA, LSEC pin 17 */
- "[I2C0_SCL]", /* GPIO_48, LS_I2C0_SCL, LSEC pin 15 */
- "[UART0_TxD]", /* GPIO_49, BLSP9_UART_TX, LSEC pin 5 */
- "[UART0_RxD]", /* GPIO_50, BLSP9_UART_RX, LSEC pin 7 */
- "[UART0_CTS]", /* GPIO_51, BLSP9_UART_CTS_N, LSEC pin 3 */
- "[UART0_RTS]", /* GPIO_52, BLSP9_UART_RFR_N, LSEC pin 9 */
- "[CODEC_INT1_N]", /* GPIO_53 */
- "[CODEC_INT2_N]", /* GPIO_54 */
- "[BLSP7_I2C_SDA]", /* GPIO_55 */
- "[BLSP7_I2C_SCL]", /* GPIO_56 */
- "MI2S_MCLK", /* GPIO_57, S HSEC pin 3 */
- "[PCM_CLK]", /* GPIO_58, QUA_MI2S_SCK, LSEC pin 18 */
- "[PCM_FS]", /* GPIO_59, QUA_MI2S_WS, LSEC pin 16 */
- "[PCM_DO]", /* GPIO_60, QUA_MI2S_DATA0, LSEC pin 20 */
- "[PCM_DI]", /* GPIO_61, QUA_MI2S_DATA1, LSEC pin 22 */
- "GPIO-E", /* GPIO_62, LSEC pin 27 */
- "TP87", /* GPIO_63 */
- "[CODEC_RST_N]", /* GPIO_64 */
- "[PCM1_CLK]", /* GPIO_65 */
- "[PCM1_SYNC]", /* GPIO_66 */
- "[PCM1_DIN]", /* GPIO_67 */
- "[PCM1_DOUT]", /* GPIO_68 */
- "AUDIO_REF_CLK", /* GPIO_69 */
- "SLIMBUS_CLK", /* GPIO_70 */
- "SLIMBUS_DATA0", /* GPIO_71 */
- "SLIMBUS_DATA1", /* GPIO_72 */
- "NC", /* GPIO_73 */
- "NC", /* GPIO_74 */
- "NC", /* GPIO_75 */
- "NC", /* GPIO_76 */
- "TP94", /* GPIO_77 */
- "NC", /* GPIO_78 */
- "TP95", /* GPIO_79 */
- "GPIO-A", /* GPIO_80, MEMS_RESET_N, LSEC pin 23 */
- "TP88", /* GPIO_81 */
- "TP89", /* GPIO_82 */
- "TP90", /* GPIO_83 */
- "TP91", /* GPIO_84 */
- "[SD_DAT0]", /* GPIO_85, BLSP12_SPI_MOSI, P HSEC pin 1 */
- "[SD_CMD]", /* GPIO_86, BLSP12_SPI_MISO, P HSEC pin 11 */
- "[SD_DAT3]", /* GPIO_87, BLSP12_SPI_CS_N, P HSEC pin 7 */
- "[SD_SCLK]", /* GPIO_88, BLSP12_SPI_CLK, P HSEC pin 9 */
- "TSIF1_CLK", /* GPIO_89, S HSEC pin 42 */
- "TSIF1_EN", /* GPIO_90, S HSEC pin 46 */
- "TSIF1_DATA", /* GPIO_91, S HSEC pin 44 */
- "NC", /* GPIO_92 */
- "TSIF2_CLK", /* GPIO_93, S HSEC pin 52 */
- "TSIF2_EN", /* GPIO_94, S HSEC pin 56 */
- "TSIF2_DATA", /* GPIO_95, S HSEC pin 54 */
- "TSIF2_SYNC", /* GPIO_96, S HSEC pin 58 */
- "NC", /* GPIO_97 */
- "CAM1_STANDBY_N", /* GPIO_98 */
- "NC", /* GPIO_99 */
- "NC", /* GPIO_100 */
- "[LCD1_RESET_N]", /* GPIO_101, S HSEC pin 51 */
- "BOOT_CONFIG1", /* GPIO_102 */
- "USB_HUB_RESET", /* GPIO_103 */
- "CAM1_RST_N", /* GPIO_104 */
- "NC", /* GPIO_105 */
- "NC", /* GPIO_106 */
- "NC", /* GPIO_107 */
- "NC", /* GPIO_108 */
- "NC", /* GPIO_109 */
- "NC", /* GPIO_110 */
- "NC", /* GPIO_111 */
- "NC", /* GPIO_112 */
- "PMI8994_BUA", /* GPIO_113 */
- "PCIE2_RST_N", /* GPIO_114 */
- "PCIE2_CLKREQ_N", /* GPIO_115 */
- "PCIE2_WAKE", /* GPIO_116 */
- "SSC_IRQ_0", /* GPIO_117 */
- "SSC_IRQ_1", /* GPIO_118 */
- "SSC_IRQ_2", /* GPIO_119 */
- "NC", /* GPIO_120 */
- "GPIO121", /* GPIO_121, S HSEC pin 2 */
- "NC", /* GPIO_122 */
- "SSC_IRQ_6", /* GPIO_123 */
- "SSC_IRQ_7", /* GPIO_124 */
- "GPIO-C", /* GPIO_125, TS_INT0, LSEC pin 25 */
- "BOOT_CONFIG5", /* GPIO_126 */
- "NC", /* GPIO_127 */
- "NC", /* GPIO_128 */
- "BOOT_CONFIG7", /* GPIO_129 */
- "PCIE1_RST_N", /* GPIO_130 */
- "PCIE1_CLKREQ_N", /* GPIO_131 */
- "PCIE1_WAKE", /* GPIO_132 */
- "GPIO-L", /* GPIO_133, CAM2_STANDBY_N, LSEC pin 34 */
- "NC", /* GPIO_134 */
- "NC", /* GPIO_135 */
- "BOOT_CONFIG8", /* GPIO_136 */
- "NC", /* GPIO_137 */
- "NC", /* GPIO_138 */
- "GPS_SSBI2", /* GPIO_139 */
- "GPS_SSBI1", /* GPIO_140 */
- "NC", /* GPIO_141 */
- "NC", /* GPIO_142 */
- "NC", /* GPIO_143 */
- "BOOT_CONFIG6", /* GPIO_144 */
- "NC", /* GPIO_145 */
- "NC", /* GPIO_146 */
- "NC", /* GPIO_147 */
- "NC", /* GPIO_148 */
- "NC"; /* GPIO_149 */
-
- sdc2_cd_on: sdc2-cd-on-state {
- pins = "gpio38";
- function = "gpio";
- bias-pull-up;
- drive-strength = <16>;
- };
-
- sdc2_cd_off: sdc2-cd-off-state {
- pins = "gpio38";
- function = "gpio";
- bias-pull-up;
- drive-strength = <2>;
- };
-
- hdmi_hpd_active: hdmi-hpd-active-state {
- pins = "gpio34";
- function = "hdmi_hot";
- bias-pull-down;
- drive-strength = <16>;
- };
-
- hdmi_hpd_suspend: hdmi-hpd-suspend-state {
- pins = "gpio34";
- function = "hdmi_hot";
- bias-pull-down;
- drive-strength = <2>;
- };
-
- hdmi_ddc_active: hdmi-ddc-active-state {
- pins = "gpio32", "gpio33";
- function = "hdmi_ddc";
- drive-strength = <2>;
- bias-pull-up;
- };
-
- hdmi_ddc_suspend: hdmi-ddc-suspend-state {
- pins = "gpio32", "gpio33";
- function = "hdmi_ddc";
- drive-strength = <2>;
- bias-pull-down;
- };
-};
-
-&pcie0 {
- status = "okay";
- perst-gpios = <&tlmm 35 GPIO_ACTIVE_LOW>;
- vddpe-3v3-supply = <&wlan_en>;
- vdda-supply = <&vreg_l28a_0p925>;
-};
-
-&pcie1 {
- status = "okay";
- perst-gpios = <&tlmm 130 GPIO_ACTIVE_LOW>;
- vdda-supply = <&vreg_l28a_0p925>;
-};
-
-&pcie2 {
- status = "okay";
- perst-gpios = <&tlmm 114 GPIO_ACTIVE_LOW>;
- vdda-supply = <&vreg_l28a_0p925>;
-};
-
-&pcie_phy {
- status = "okay";
-
- vdda-phy-supply = <&vreg_l28a_0p925>;
- vdda-pll-supply = <&vreg_l12a_1p8>;
-};
-
-&pm8994_gpios {
- gpio-line-names =
- "NC",
- "KEY_VOLP_N",
- "NC",
- "BL1_PWM",
- "GPIO-F", /* BL0_PWM, LSEC pin 28 */
- "BL1_EN",
- "NC",
- "WLAN_EN",
- "NC",
- "NC",
- "NC",
- "NC",
- "NC",
- "NC",
- "DIVCLK1",
- "DIVCLK2",
- "DIVCLK3",
- "DIVCLK4",
- "BT_EN",
- "PMIC_SLB",
- "PMIC_BUA",
- "USB_VBUS_DET";
-
- pinctrl-names = "default";
- pinctrl-0 = <&ls_exp_gpio_f &bt_en_gpios>;
-
- ls_exp_gpio_f: pm8994-gpio5-state {
- pinconf {
- pins = "gpio5";
- function = PMIC_GPIO_FUNC_NORMAL;
- output-low;
- power-source = <PM8994_GPIO_S4>; /* 1.8V */
- };
- };
-
- bt_en_gpios: bt-en-pios-state {
- pinconf {
- pins = "gpio19";
- function = PMIC_GPIO_FUNC_NORMAL;
- output-low;
- power-source = <PM8994_GPIO_S4>; /* 1.8V */
- qcom,drive-strength = <PMIC_GPIO_STRENGTH_LOW>;
- bias-pull-down;
- };
- };
-
- wlan_en_gpios: wlan-en-gpios-state {
- pinconf {
- pins = "gpio8";
- function = PMIC_GPIO_FUNC_NORMAL;
- output-low;
- power-source = <PM8994_GPIO_S4>; /* 1.8V */
- qcom,drive-strength = <PMIC_GPIO_STRENGTH_LOW>;
- bias-pull-down;
- };
- };
-
- audio_mclk: clk-div1-state {
- pinconf {
- pins = "gpio15";
- function = "func1";
- power-source = <PM8994_GPIO_S4>; /* 1.8V */
- };
- };
-
- volume_up_gpio: pm8996-gpio2-state {
- pinconf {
- pins = "gpio2";
- function = "normal";
- input-enable;
- drive-push-pull;
- bias-pull-up;
- qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
- power-source = <PM8994_GPIO_S4>; /* 1.8V */
- };
- };
-
- divclk4_pin_a: divclk4-state {
- pinconf {
- pins = "gpio18";
- function = PMIC_GPIO_FUNC_FUNC2;
-
- bias-disable;
- power-source = <PM8994_GPIO_S4>;
- };
- };
-
- usb3_vbus_det_gpio: pm8996-gpio22-state {
- pinconf {
- pins = "gpio22";
- function = PMIC_GPIO_FUNC_NORMAL;
- input-enable;
- bias-pull-down;
- qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
- power-source = <PM8994_GPIO_S4>; /* 1.8V */
- };
- };
-};
-
-&pm8994_mpps {
- gpio-line-names =
- "VDDPX_BIAS",
- "WIFI_LED",
- "NC",
- "BT_LED",
- "PM_MPP05",
- "PM_MPP06",
- "PM_MPP07",
- "NC";
-};
-
-&pm8994_spmi_regulators {
- qcom,saw-reg = <&saw3>;
- vdd_s11-supply = <&vph_pwr>;
-
- s9 {
- qcom,saw-slave;
- };
- s10 {
- qcom,saw-slave;
- };
- s11 {
- qcom,saw-leader;
- regulator-name = "VDD_APCC";
- regulator-always-on;
- regulator-min-microvolt = <980000>;
- regulator-max-microvolt = <980000>;
- };
-};
-
-&pmi8994_gpios {
- gpio-line-names =
- "NC",
- "SPKR_AMP_EN1",
- "SPKR_AMP_EN2",
- "TP61",
- "NC",
- "USB2_VBUS_DET",
- "NC",
- "NC",
- "NC",
- "NC";
-
- usb2_vbus_det_gpio: pmi8996-gpio6-state {
- pinconf {
- pins = "gpio6";
- function = PMIC_GPIO_FUNC_NORMAL;
- input-enable;
- bias-pull-down;
- qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
- power-source = <PM8994_GPIO_S4>; /* 1.8V */
- };
- };
-};
-
-&pmi8994_lpg {
- qcom,power-source = <1>;
-
- pinctrl-names = "default";
- pinctrl-0 = <&pmi8994_mpp2_userled4>;
-
- qcom,dtest = <0 0>,
- <0 0>,
- <0 0>,
- <4 1>;
-
- status = "okay";
-
- led@1 {
- reg = <1>;
- color = <LED_COLOR_ID_GREEN>;
- function = LED_FUNCTION_HEARTBEAT;
- function-enumerator = <1>;
-
- linux,default-trigger = "heartbeat";
- default-state = "on";
- };
-
- led@2 {
- reg = <2>;
- color = <LED_COLOR_ID_GREEN>;
- function = LED_FUNCTION_HEARTBEAT;
- function-enumerator = <0>;
- };
-
- led@3 {
- reg = <3>;
- color = <LED_COLOR_ID_GREEN>;
- function = LED_FUNCTION_HEARTBEAT;
- function-enumerator = <2>;
- };
-
- led@4 {
- reg = <4>;
- color = <LED_COLOR_ID_GREEN>;
- function = LED_FUNCTION_HEARTBEAT;
- function-enumerator = <3>;
- };
-};
-
-&pmi8994_mpps {
- pmi8994_mpp2_userled4: mpp2-userled4-state {
- pins = "mpp2";
- function = "sink";
-
- output-low;
- qcom,dtest = <4>;
- };
-};
-
-&pmi8994_spmi_regulators {
- vdd_s2-supply = <&vph_pwr>;
-
- vdd_gfx: s2 {
- regulator-name = "VDD_GFX";
- regulator-min-microvolt = <980000>;
- regulator-max-microvolt = <980000>;
- };
-};
-
-&rpm_requests {
- regulators-0 {
- compatible = "qcom,rpm-pm8994-regulators";
-
- vdd_s1-supply = <&vph_pwr>;
- vdd_s2-supply = <&vph_pwr>;
- vdd_s3-supply = <&vph_pwr>;
- vdd_s4-supply = <&vph_pwr>;
- vdd_s5-supply = <&vph_pwr>;
- vdd_s6-supply = <&vph_pwr>;
- vdd_s7-supply = <&vph_pwr>;
- vdd_s8-supply = <&vph_pwr>;
- vdd_s9-supply = <&vph_pwr>;
- vdd_s10-supply = <&vph_pwr>;
- vdd_s11-supply = <&vph_pwr>;
- vdd_s12-supply = <&vph_pwr>;
- vdd_l1-supply = <&vreg_s1b_1p025>;
- vdd_l2_l26_l28-supply = <&vreg_s3a_1p3>;
- vdd_l3_l11-supply = <&vreg_s3a_1p3>;
- vdd_l4_l27_l31-supply = <&vreg_s3a_1p3>;
- vdd_l5_l7-supply = <&vreg_s5a_2p15>;
- vdd_l6_l12_l32-supply = <&vreg_s5a_2p15>;
- vdd_l8_l16_l30-supply = <&vph_pwr>;
- vdd_l9_l10_l18_l22-supply = <&vph_pwr_bbyp>;
- vdd_l13_l19_l23_l24-supply = <&vph_pwr_bbyp>;
- vdd_l14_l15-supply = <&vreg_s5a_2p15>;
- vdd_l17_l29-supply = <&vph_pwr_bbyp>;
- vdd_l20_l21-supply = <&vph_pwr_bbyp>;
- vdd_l25-supply = <&vreg_s3a_1p3>;
- vdd_lvs1_2-supply = <&vreg_s4a_1p8>;
-
- vreg_s3a_1p3: s3 {
- regulator-name = "vreg_s3a_1p3";
- regulator-min-microvolt = <1300000>;
- regulator-max-microvolt = <1300000>;
- };
-
- /**
- * 1.8v required on LS expansion
- * for mezzanine boards
- */
- vreg_s4a_1p8: s4 {
- regulator-name = "vreg_s4a_1p8";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- };
- vreg_s5a_2p15: s5 {
- regulator-name = "vreg_s5a_2p15";
- regulator-min-microvolt = <2150000>;
- regulator-max-microvolt = <2150000>;
- };
- vreg_s7a_1p0: s7 {
- regulator-name = "vreg_s7a_1p0";
- regulator-min-microvolt = <800000>;
- regulator-max-microvolt = <800000>;
- };
-
- vreg_l1a_1p0: l1 {
- regulator-name = "vreg_l1a_1p0";
- regulator-min-microvolt = <1000000>;
- regulator-max-microvolt = <1000000>;
- };
- vreg_l2a_1p25: l2 {
- regulator-name = "vreg_l2a_1p25";
- regulator-min-microvolt = <1250000>;
- regulator-max-microvolt = <1250000>;
- };
- vreg_l3a_0p875: l3 {
- regulator-name = "vreg_l3a_0p875";
- regulator-min-microvolt = <850000>;
- regulator-max-microvolt = <850000>;
- };
- vreg_l4a_1p225: l4 {
- regulator-name = "vreg_l4a_1p225";
- regulator-min-microvolt = <1225000>;
- regulator-max-microvolt = <1225000>;
- };
- vreg_l6a_1p2: l6 {
- regulator-name = "vreg_l6a_1p2";
- regulator-min-microvolt = <1200000>;
- regulator-max-microvolt = <1200000>;
- };
- vreg_l8a_1p8: l8 {
- regulator-name = "vreg_l8a_1p8";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
- vreg_l9a_1p8: l9 {
- regulator-name = "vreg_l9a_1p8";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
- vreg_l10a_1p8: l10 {
- regulator-name = "vreg_l10a_1p8";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
- vreg_l11a_1p15: l11 {
- regulator-name = "vreg_l11a_1p15";
- regulator-min-microvolt = <1150000>;
- regulator-max-microvolt = <1150000>;
- };
- vreg_l12a_1p8: l12 {
- regulator-name = "vreg_l12a_1p8";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
- vreg_l13a_2p95: l13 {
- regulator-name = "vreg_l13a_2p95";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <2950000>;
- };
- vreg_l14a_1p8: l14 {
- regulator-name = "vreg_l14a_1p8";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
- vreg_l15a_1p8: l15 {
- regulator-name = "vreg_l15a_1p8";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
- vreg_l16a_2p7: l16 {
- regulator-name = "vreg_l16a_2p7";
- regulator-min-microvolt = <2700000>;
- regulator-max-microvolt = <2700000>;
- };
- vreg_l17a_2p8: l17 {
- regulator-name = "vreg_l17a_2p8";
- regulator-min-microvolt = <2500000>;
- regulator-max-microvolt = <2500000>;
- };
- vreg_l18a_2p85: l18 {
- regulator-name = "vreg_l18a_2p85";
- regulator-min-microvolt = <2700000>;
- regulator-max-microvolt = <2900000>;
- };
- vreg_l19a_2p8: l19 {
- regulator-name = "vreg_l19a_2p8";
- regulator-min-microvolt = <3000000>;
- regulator-max-microvolt = <3000000>;
- };
- vreg_l20a_2p95: l20 {
- regulator-name = "vreg_l20a_2p95";
- regulator-min-microvolt = <2950000>;
- regulator-max-microvolt = <2950000>;
- regulator-allow-set-load;
- };
- vreg_l21a_2p95: l21 {
- regulator-name = "vreg_l21a_2p95";
- regulator-min-microvolt = <2950000>;
- regulator-max-microvolt = <2950000>;
- regulator-allow-set-load;
- regulator-system-load = <200000>;
- };
- vreg_l22a_3p0: l22 {
- regulator-name = "vreg_l22a_3p0";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- };
- vreg_l23a_2p8: l23 {
- regulator-name = "vreg_l23a_2p8";
- regulator-min-microvolt = <2800000>;
- regulator-max-microvolt = <2800000>;
- };
- vreg_l24a_3p075: l24 {
- regulator-name = "vreg_l24a_3p075";
- regulator-min-microvolt = <3075000>;
- regulator-max-microvolt = <3075000>;
- };
- vreg_l25a_1p2: l25 {
- regulator-name = "vreg_l25a_1p2";
- regulator-min-microvolt = <1200000>;
- regulator-max-microvolt = <1200000>;
- regulator-allow-set-load;
- };
- vreg_l26a_0p8: l27 {
- regulator-name = "vreg_l26a_0p8";
- regulator-min-microvolt = <1000000>;
- regulator-max-microvolt = <1000000>;
- };
- vreg_l28a_0p925: l28 {
- regulator-name = "vreg_l28a_0p925";
- regulator-min-microvolt = <925000>;
- regulator-max-microvolt = <925000>;
- regulator-allow-set-load;
- };
- vreg_l29a_2p8: l29 {
- regulator-name = "vreg_l29a_2p8";
- regulator-min-microvolt = <2800000>;
- regulator-max-microvolt = <2800000>;
- };
- vreg_l30a_1p8: l30 {
- regulator-name = "vreg_l30a_1p8";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
- vreg_l32a_1p8: l32 {
- regulator-name = "vreg_l32a_1p8";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- vreg_lvs1a_1p8: lvs1 {
- regulator-name = "vreg_lvs1a_1p8";
- };
-
- vreg_lvs2a_1p8: lvs2 {
- regulator-name = "vreg_lvs2a_1p8";
- };
- };
-
- regulators-1 {
- compatible = "qcom,rpm-pmi8994-regulators";
-
- vdd_s1-supply = <&vph_pwr>;
- vdd_s2-supply = <&vph_pwr>;
- vdd_s3-supply = <&vph_pwr>;
- vdd_bst_byp-supply = <&vph_pwr>;
-
- vph_pwr_bbyp: boost-bypass {
- regulator-name = "vph_pwr_bbyp";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- };
-
- vreg_s1b_1p025: s1 {
- regulator-name = "vreg_s1b_1p025";
- regulator-min-microvolt = <1025000>;
- regulator-max-microvolt = <1025000>;
- };
- };
-};
-
-&sdhc2 {
- /* External SD card */
- pinctrl-names = "default", "sleep";
- pinctrl-0 = <&sdc2_state_on &sdc2_cd_on>;
- pinctrl-1 = <&sdc2_state_off &sdc2_cd_off>;
- cd-gpios = <&tlmm 38 GPIO_ACTIVE_LOW>;
- vmmc-supply = <&vreg_l21a_2p95>;
- vqmmc-supply = <&vreg_l13a_2p95>;
- status = "okay";
-};
-
-&q6asmdai {
- dai@0 {
- reg = <MSM_FRONTEND_DAI_MULTIMEDIA1>;
- };
-
- dai@1 {
- reg = <MSM_FRONTEND_DAI_MULTIMEDIA2>;
- };
-
- dai@2 {
- reg = <MSM_FRONTEND_DAI_MULTIMEDIA3>;
- };
-};
-
-&slim_msm {
- status = "okay";
-
- slim@1 {
- reg = <1>;
- #address-cells = <2>;
- #size-cells = <0>;
-
- tasha_ifd: tas-ifd@0,0 {
- compatible = "slim217,1a0";
- reg = <0 0>;
- };
-
- wcd9335: codec@1,0 {
- compatible = "slim217,1a0";
- reg = <1 0>;
-
- clock-names = "mclk", "slimbus";
- clocks = <&div1_mclk>,
- <&rpmcc RPM_SMD_BB_CLK1>;
- interrupt-parent = <&tlmm>;
- interrupts = <54 IRQ_TYPE_LEVEL_HIGH>,
- <53 IRQ_TYPE_LEVEL_HIGH>;
- interrupt-names = "intr1", "intr2";
- interrupt-controller;
- #interrupt-cells = <1>;
-
- pinctrl-0 = <&cdc_reset_active &wcd_intr_default>;
- pinctrl-names = "default";
-
- reset-gpios = <&tlmm 64 GPIO_ACTIVE_LOW>;
- slim-ifc-dev = <&tasha_ifd>;
-
- #sound-dai-cells = <1>;
-
- vdd-buck-supply = <&vreg_s4a_1p8>;
- vdd-buck-sido-supply = <&vreg_s4a_1p8>;
- vdd-tx-supply = <&vreg_s4a_1p8>;
- vdd-rx-supply = <&vreg_s4a_1p8>;
- vdd-io-supply = <&vreg_s4a_1p8>;
- };
- };
-};
-
-&sound {
- compatible = "qcom,apq8096-sndcard";
- model = "DB820c";
- audio-routing = "RX_BIAS", "MCLK";
-
- mm1-dai-link {
- link-name = "MultiMedia1";
- cpu {
- sound-dai = <&q6asmdai MSM_FRONTEND_DAI_MULTIMEDIA1>;
- };
- };
-
- mm2-dai-link {
- link-name = "MultiMedia2";
- cpu {
- sound-dai = <&q6asmdai MSM_FRONTEND_DAI_MULTIMEDIA2>;
- };
- };
-
- mm3-dai-link {
- link-name = "MultiMedia3";
- cpu {
- sound-dai = <&q6asmdai MSM_FRONTEND_DAI_MULTIMEDIA3>;
- };
- };
-
- hdmi-dai-link {
- link-name = "HDMI";
- cpu {
- sound-dai = <&q6afedai HDMI_RX>;
- };
-
- platform {
- sound-dai = <&q6routing>;
- };
-
- codec {
- sound-dai = <&mdss_hdmi 0>;
- };
- };
-
- slim-dai-link {
- link-name = "SLIM Playback";
- cpu {
- sound-dai = <&q6afedai SLIMBUS_6_RX>;
- };
-
- platform {
- sound-dai = <&q6routing>;
- };
-
- codec {
- sound-dai = <&wcd9335 AIF4_PB>;
- };
- };
-
- slimcap-dai-link {
- link-name = "SLIM Capture";
- cpu {
- sound-dai = <&q6afedai SLIMBUS_0_TX>;
- };
-
- platform {
- sound-dai = <&q6routing>;
- };
-
- codec {
- sound-dai = <&wcd9335 AIF1_CAP>;
- };
- };
-};
-
-&ufsphy {
- status = "okay";
-
- vdda-phy-supply = <&vreg_l28a_0p925>;
- vdda-pll-supply = <&vreg_l12a_1p8>;
-};
-
-&ufshc {
- status = "okay";
-
- vcc-supply = <&vreg_l20a_2p95>;
- vccq-supply = <&vreg_l25a_1p2>;
- vccq2-supply = <&vreg_s4a_1p8>;
- vdd-hba-supply = <&vreg_l25a_1p2>;
-
- vcc-max-microamp = <600000>;
- vccq-max-microamp = <450000>;
- vccq2-max-microamp = <450000>;
-};
-
-&usb2 {
- status = "okay";
- extcon = <&usb2_id>;
-};
-
-&usb2_dwc3 {
- extcon = <&usb2_id>;
- dr_mode = "otg";
- maximum-speed = "high-speed";
-};
-
-&usb3 {
- status = "okay";
- extcon = <&usb3_id>;
-};
-
-&usb3_dwc3 {
- extcon = <&usb3_id>;
- dr_mode = "otg";
-};
-
-&usb3phy {
- status = "okay";
-
- vdda-phy-supply = <&vreg_l28a_0p925>;
- vdda-pll-supply = <&vreg_l12a_1p8>;
-};
-
-&venus {
- status = "okay";
};
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (c) 2014-2016, The Linux Foundation. All rights reserved.
+ */
+
+
+#include "pm8994.dtsi"
+#include "pmi8994.dtsi"
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
+#include <dt-bindings/sound/qcom,q6afe.h>
+#include <dt-bindings/sound/qcom,q6asm.h>
+#include <dt-bindings/sound/qcom,wcd9335.h>
+
+/*
+ * GPIO name legend: proper name = the GPIO line is used as GPIO
+ * NC = not connected (pin out but not routed from the chip to
+ * anything the board)
+ * "[PER]" = pin is muxed for [peripheral] (not GPIO)
+ * LSEC = Low Speed External Connector
+ * P HSEC = Primary High Speed External Connector
+ * S HSEC = Secondary High Speed External Connector
+ * J14 = Camera Connector
+ * TP = Test Points
+ *
+ * Line names are taken from the schematic "DragonBoard 820c",
+ * drawing no: LM25-P2751-1
+ *
+ * For the lines routed to the external connectors the
+ * lines are named after the 96Boards CE Specification 1.0,
+ * Appendix "Expansion Connector Signal Description".
+ *
+ * When the 96Board naming of a line and the schematic name of
+ * the same line are in conflict, the 96Board specification
+ * takes precedence, which means that the external UART on the
+ * LSEC is named UART0 while the schematic and SoC names this
+ * UART3. This is only for the informational lines i.e. "[FOO]",
+ * the GPIO named lines "GPIO-A" thru "GPIO-L" are the only
+ * ones actually used for GPIO.
+ */
+
+/ {
+ aliases {
+ serial0 = &blsp2_uart2;
+ serial1 = &blsp2_uart3;
+ serial2 = &blsp1_uart2;
+ i2c0 = &blsp1_i2c3;
+ i2c1 = &blsp2_i2c1;
+ i2c2 = &blsp2_i2c1;
+ spi0 = &blsp1_spi1;
+ spi1 = &blsp2_spi6;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ div1_mclk: divclk1 {
+ compatible = "gpio-gate-clock";
+ pinctrl-0 = <&audio_mclk>;
+ pinctrl-names = "default";
+ clocks = <&rpmcc RPM_SMD_DIV_CLK1>;
+ #clock-cells = <0>;
+ enable-gpios = <&pm8994_gpios 15 0>;
+ };
+
+ divclk4: divclk4 {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <32768>;
+ clock-output-names = "divclk4";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&divclk4_pin_a>;
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+ autorepeat;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&volume_up_gpio>;
+
+ button {
+ label = "Volume Up";
+ linux,code = <KEY_VOLUMEUP>;
+ gpios = <&pm8994_gpios 2 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ usb2_id: usb2-id {
+ compatible = "linux,extcon-usb-gpio";
+ id-gpios = <&pmi8994_gpios 6 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&usb2_vbus_det_gpio>;
+ };
+
+ usb3_id: usb3-id {
+ compatible = "linux,extcon-usb-gpio";
+ id-gpios = <&pm8994_gpios 22 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&usb3_vbus_det_gpio>;
+ };
+
+ vph_pwr: vph-pwr-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vph_pwr";
+ regulator-always-on;
+ regulator-boot-on;
+
+ regulator-min-microvolt = <3700000>;
+ regulator-max-microvolt = <3700000>;
+ };
+
+ wlan_en: wlan-en-1-8v {
+ pinctrl-names = "default";
+ pinctrl-0 = <&wlan_en_gpios>;
+ compatible = "regulator-fixed";
+ regulator-name = "wlan-en-regulator";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+
+ gpio = <&pm8994_gpios 8 0>;
+
+ /* WLAN card specific delay */
+ startup-delay-us = <70000>;
+ enable-active-high;
+ };
+};
+
+&blsp1_i2c3 {
+ /* On Low speed expansion: LS-I2C0 */
+ status = "okay";
+};
+
+&blsp1_spi1 {
+ /* On Low speed expansion */
+ status = "okay";
+};
+
+&blsp1_uart2 {
+ label = "BT-UART";
+ status = "okay";
+
+ bluetooth {
+ compatible = "qcom,qca6174-bt";
+
+ /* bt_disable_n gpio */
+ enable-gpios = <&pm8994_gpios 19 GPIO_ACTIVE_HIGH>;
+
+ clocks = <&divclk4>;
+ };
+};
+
+&adsp_pil {
+ status = "okay";
+ firmware-name = "qcom/apq8096/adsp.mbn";
+};
+
+&blsp2_i2c1 {
+ /* On High speed expansion: HS-I2C2 */
+ status = "okay";
+};
+
+&blsp2_i2c1 {
+ /* On Low speed expansion: LS-I2C1 */
+ status = "okay";
+};
+
+&blsp2_spi6 {
+ /* On High speed expansion */
+ status = "okay";
+};
+
+&blsp2_uart2 {
+ label = "LS-UART1";
+ status = "okay";
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&blsp2_uart2_2pins_default>;
+ pinctrl-1 = <&blsp2_uart2_2pins_sleep>;
+};
+
+&blsp2_uart3 {
+ label = "LS-UART0";
+ status = "disabled";
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&blsp2_uart3_4pins_default>;
+ pinctrl-1 = <&blsp2_uart3_4pins_sleep>;
+};
+
+&camss {
+ vdda-supply = <&vreg_l2a_1p25>;
+};
+
+&gpu {
+ status = "okay";
+};
+
+&gpu_zap_shader {
+ firmware-name = "qcom/apq8096/a530_zap.mbn";
+};
+
+&hsusb_phy1 {
+ status = "okay";
+
+ vdd-supply = <&vreg_l28a_0p925>;
+ vdda-pll-supply = <&vreg_l12a_1p8>;
+ vdda-phy-dpdm-supply = <&vreg_l24a_3p075>;
+};
+
+&hsusb_phy2 {
+ status = "okay";
+
+ vdd-supply = <&vreg_l28a_0p925>;
+ vdda-pll-supply = <&vreg_l12a_1p8>;
+ vdda-phy-dpdm-supply = <&vreg_l24a_3p075>;
+};
+
+&mdp {
+ status = "okay";
+};
+
+&mdss {
+ status = "okay";
+};
+
+&mdss_hdmi {
+ status = "okay";
+
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&hdmi_hpd_active &hdmi_ddc_active>;
+ pinctrl-1 = <&hdmi_hpd_suspend &hdmi_ddc_suspend>;
+
+ core-vdda-supply = <&vreg_l12a_1p8>;
+ core-vcc-supply = <&vreg_s4a_1p8>;
+};
+
+&mdss_hdmi_phy {
+ status = "okay";
+
+ vddio-supply = <&vreg_l12a_1p8>;
+ vcca-supply = <&vreg_l28a_0p925>;
+ #phy-cells = <0>;
+};
+
+&mmcc {
+ vdd-gfx-supply = <&vdd_gfx>;
+};
+
+&mss_pil {
+ status = "okay";
+ pll-supply = <&vreg_l12a_1p8>;
+ firmware-name = "qcom/apq8096/mba.mbn", "qcom/apq8096/modem.mbn";
+};
+
+&pm8994_resin {
+ status = "okay";
+ linux,code = <KEY_VOLUMEDOWN>;
+};
+
+&tlmm {
+ gpio-line-names =
+ "[SPI0_DOUT]", /* GPIO_0, BLSP1_SPI_MOSI, LSEC pin 14 */
+ "[SPI0_DIN]", /* GPIO_1, BLSP1_SPI_MISO, LSEC pin 10 */
+ "[SPI0_CS]", /* GPIO_2, BLSP1_SPI_CS_N, LSEC pin 12 */
+ "[SPI0_SCLK]", /* GPIO_3, BLSP1_SPI_CLK, LSEC pin 8 */
+ "[UART1_TxD]", /* GPIO_4, BLSP8_UART_TX, LSEC pin 11 */
+ "[UART1_RxD]", /* GPIO_5, BLSP8_UART_RX, LSEC pin 13 */
+ "[I2C1_SDA]", /* GPIO_6, BLSP8_I2C_SDA, LSEC pin 21 */
+ "[I2C1_SCL]", /* GPIO_7, BLSP8_I2C_SCL, LSEC pin 19 */
+ "GPIO-H", /* GPIO_8, LCD0_RESET_N, LSEC pin 30 */
+ "TP93", /* GPIO_9 */
+ "GPIO-G", /* GPIO_10, MDP_VSYNC_P, LSEC pin 29 */
+ "[MDP_VSYNC_S]", /* GPIO_11, S HSEC pin 55 */
+ "NC", /* GPIO_12 */
+ "[CSI0_MCLK]", /* GPIO_13, CAM_MCLK0, P HSEC pin 15 */
+ "[CAM_MCLK1]", /* GPIO_14, J14 pin 11 */
+ "[CSI1_MCLK]", /* GPIO_15, CAM_MCLK2, P HSEC pin 17 */
+ "TP99", /* GPIO_16 */
+ "[I2C2_SDA]", /* GPIO_17, CCI_I2C_SDA0, P HSEC pin 34 */
+ "[I2C2_SCL]", /* GPIO_18, CCI_I2C_SCL0, P HSEC pin 32 */
+ "[CCI_I2C_SDA1]", /* GPIO_19, S HSEC pin 38 */
+ "[CCI_I2C_SCL1]", /* GPIO_20, S HSEC pin 36 */
+ "FLASH_STROBE_EN", /* GPIO_21, S HSEC pin 5 */
+ "FLASH_STROBE_TRIG", /* GPIO_22, S HSEC pin 1 */
+ "GPIO-K", /* GPIO_23, CAM2_RST_N, LSEC pin 33 */
+ "GPIO-D", /* GPIO_24, LSEC pin 26 */
+ "GPIO-I", /* GPIO_25, CAM0_RST_N, LSEC pin 31 */
+ "GPIO-J", /* GPIO_26, CAM0_STANDBY_N, LSEC pin 32 */
+ "BLSP6_I2C_SDA", /* GPIO_27 */
+ "BLSP6_I2C_SCL", /* GPIO_28 */
+ "GPIO-B", /* GPIO_29, TS0_RESET_N, LSEC pin 24 */
+ "GPIO30", /* GPIO_30, S HSEC pin 4 */
+ "HDMI_CEC", /* GPIO_31 */
+ "HDMI_DDC_CLOCK", /* GPIO_32 */
+ "HDMI_DDC_DATA", /* GPIO_33 */
+ "HDMI_HOT_PLUG_DETECT", /* GPIO_34 */
+ "PCIE0_RST_N", /* GPIO_35 */
+ "PCIE0_CLKREQ_N", /* GPIO_36 */
+ "PCIE0_WAKE", /* GPIO_37 */
+ "SD_CARD_DET_N", /* GPIO_38 */
+ "TSIF1_SYNC", /* GPIO_39, S HSEC pin 48 */
+ "W_DISABLE_N", /* GPIO_40 */
+ "[BLSP9_UART_TX]", /* GPIO_41 */
+ "[BLSP9_UART_RX]", /* GPIO_42 */
+ "[BLSP2_UART_CTS_N]", /* GPIO_43 */
+ "[BLSP2_UART_RFR_N]", /* GPIO_44 */
+ "[BLSP3_UART_TX]", /* GPIO_45 */
+ "[BLSP3_UART_RX]", /* GPIO_46 */
+ "[I2C0_SDA]", /* GPIO_47, LS_I2C0_SDA, LSEC pin 17 */
+ "[I2C0_SCL]", /* GPIO_48, LS_I2C0_SCL, LSEC pin 15 */
+ "[UART0_TxD]", /* GPIO_49, BLSP9_UART_TX, LSEC pin 5 */
+ "[UART0_RxD]", /* GPIO_50, BLSP9_UART_RX, LSEC pin 7 */
+ "[UART0_CTS]", /* GPIO_51, BLSP9_UART_CTS_N, LSEC pin 3 */
+ "[UART0_RTS]", /* GPIO_52, BLSP9_UART_RFR_N, LSEC pin 9 */
+ "[CODEC_INT1_N]", /* GPIO_53 */
+ "[CODEC_INT2_N]", /* GPIO_54 */
+ "[BLSP7_I2C_SDA]", /* GPIO_55 */
+ "[BLSP7_I2C_SCL]", /* GPIO_56 */
+ "MI2S_MCLK", /* GPIO_57, S HSEC pin 3 */
+ "[PCM_CLK]", /* GPIO_58, QUA_MI2S_SCK, LSEC pin 18 */
+ "[PCM_FS]", /* GPIO_59, QUA_MI2S_WS, LSEC pin 16 */
+ "[PCM_DO]", /* GPIO_60, QUA_MI2S_DATA0, LSEC pin 20 */
+ "[PCM_DI]", /* GPIO_61, QUA_MI2S_DATA1, LSEC pin 22 */
+ "GPIO-E", /* GPIO_62, LSEC pin 27 */
+ "TP87", /* GPIO_63 */
+ "[CODEC_RST_N]", /* GPIO_64 */
+ "[PCM1_CLK]", /* GPIO_65 */
+ "[PCM1_SYNC]", /* GPIO_66 */
+ "[PCM1_DIN]", /* GPIO_67 */
+ "[PCM1_DOUT]", /* GPIO_68 */
+ "AUDIO_REF_CLK", /* GPIO_69 */
+ "SLIMBUS_CLK", /* GPIO_70 */
+ "SLIMBUS_DATA0", /* GPIO_71 */
+ "SLIMBUS_DATA1", /* GPIO_72 */
+ "NC", /* GPIO_73 */
+ "NC", /* GPIO_74 */
+ "NC", /* GPIO_75 */
+ "NC", /* GPIO_76 */
+ "TP94", /* GPIO_77 */
+ "NC", /* GPIO_78 */
+ "TP95", /* GPIO_79 */
+ "GPIO-A", /* GPIO_80, MEMS_RESET_N, LSEC pin 23 */
+ "TP88", /* GPIO_81 */
+ "TP89", /* GPIO_82 */
+ "TP90", /* GPIO_83 */
+ "TP91", /* GPIO_84 */
+ "[SD_DAT0]", /* GPIO_85, BLSP12_SPI_MOSI, P HSEC pin 1 */
+ "[SD_CMD]", /* GPIO_86, BLSP12_SPI_MISO, P HSEC pin 11 */
+ "[SD_DAT3]", /* GPIO_87, BLSP12_SPI_CS_N, P HSEC pin 7 */
+ "[SD_SCLK]", /* GPIO_88, BLSP12_SPI_CLK, P HSEC pin 9 */
+ "TSIF1_CLK", /* GPIO_89, S HSEC pin 42 */
+ "TSIF1_EN", /* GPIO_90, S HSEC pin 46 */
+ "TSIF1_DATA", /* GPIO_91, S HSEC pin 44 */
+ "NC", /* GPIO_92 */
+ "TSIF2_CLK", /* GPIO_93, S HSEC pin 52 */
+ "TSIF2_EN", /* GPIO_94, S HSEC pin 56 */
+ "TSIF2_DATA", /* GPIO_95, S HSEC pin 54 */
+ "TSIF2_SYNC", /* GPIO_96, S HSEC pin 58 */
+ "NC", /* GPIO_97 */
+ "CAM1_STANDBY_N", /* GPIO_98 */
+ "NC", /* GPIO_99 */
+ "NC", /* GPIO_100 */
+ "[LCD1_RESET_N]", /* GPIO_101, S HSEC pin 51 */
+ "BOOT_CONFIG1", /* GPIO_102 */
+ "USB_HUB_RESET", /* GPIO_103 */
+ "CAM1_RST_N", /* GPIO_104 */
+ "NC", /* GPIO_105 */
+ "NC", /* GPIO_106 */
+ "NC", /* GPIO_107 */
+ "NC", /* GPIO_108 */
+ "NC", /* GPIO_109 */
+ "NC", /* GPIO_110 */
+ "NC", /* GPIO_111 */
+ "NC", /* GPIO_112 */
+ "PMI8994_BUA", /* GPIO_113 */
+ "PCIE2_RST_N", /* GPIO_114 */
+ "PCIE2_CLKREQ_N", /* GPIO_115 */
+ "PCIE2_WAKE", /* GPIO_116 */
+ "SSC_IRQ_0", /* GPIO_117 */
+ "SSC_IRQ_1", /* GPIO_118 */
+ "SSC_IRQ_2", /* GPIO_119 */
+ "NC", /* GPIO_120 */
+ "GPIO121", /* GPIO_121, S HSEC pin 2 */
+ "NC", /* GPIO_122 */
+ "SSC_IRQ_6", /* GPIO_123 */
+ "SSC_IRQ_7", /* GPIO_124 */
+ "GPIO-C", /* GPIO_125, TS_INT0, LSEC pin 25 */
+ "BOOT_CONFIG5", /* GPIO_126 */
+ "NC", /* GPIO_127 */
+ "NC", /* GPIO_128 */
+ "BOOT_CONFIG7", /* GPIO_129 */
+ "PCIE1_RST_N", /* GPIO_130 */
+ "PCIE1_CLKREQ_N", /* GPIO_131 */
+ "PCIE1_WAKE", /* GPIO_132 */
+ "GPIO-L", /* GPIO_133, CAM2_STANDBY_N, LSEC pin 34 */
+ "NC", /* GPIO_134 */
+ "NC", /* GPIO_135 */
+ "BOOT_CONFIG8", /* GPIO_136 */
+ "NC", /* GPIO_137 */
+ "NC", /* GPIO_138 */
+ "GPS_SSBI2", /* GPIO_139 */
+ "GPS_SSBI1", /* GPIO_140 */
+ "NC", /* GPIO_141 */
+ "NC", /* GPIO_142 */
+ "NC", /* GPIO_143 */
+ "BOOT_CONFIG6", /* GPIO_144 */
+ "NC", /* GPIO_145 */
+ "NC", /* GPIO_146 */
+ "NC", /* GPIO_147 */
+ "NC", /* GPIO_148 */
+ "NC"; /* GPIO_149 */
+
+ sdc2_cd_on: sdc2-cd-on-state {
+ pins = "gpio38";
+ function = "gpio";
+ bias-pull-up;
+ drive-strength = <16>;
+ };
+
+ sdc2_cd_off: sdc2-cd-off-state {
+ pins = "gpio38";
+ function = "gpio";
+ bias-pull-up;
+ drive-strength = <2>;
+ };
+
+ hdmi_hpd_active: hdmi-hpd-active-state {
+ pins = "gpio34";
+ function = "hdmi_hot";
+ bias-pull-down;
+ drive-strength = <16>;
+ };
+
+ hdmi_hpd_suspend: hdmi-hpd-suspend-state {
+ pins = "gpio34";
+ function = "hdmi_hot";
+ bias-pull-down;
+ drive-strength = <2>;
+ };
+
+ hdmi_ddc_active: hdmi-ddc-active-state {
+ pins = "gpio32", "gpio33";
+ function = "hdmi_ddc";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+
+ hdmi_ddc_suspend: hdmi-ddc-suspend-state {
+ pins = "gpio32", "gpio33";
+ function = "hdmi_ddc";
+ drive-strength = <2>;
+ bias-pull-down;
+ };
+};
+
+&pcie0 {
+ status = "okay";
+ perst-gpios = <&tlmm 35 GPIO_ACTIVE_LOW>;
+ vddpe-3v3-supply = <&wlan_en>;
+ vdda-supply = <&vreg_l28a_0p925>;
+};
+
+&pcie1 {
+ status = "okay";
+ perst-gpios = <&tlmm 130 GPIO_ACTIVE_LOW>;
+ vdda-supply = <&vreg_l28a_0p925>;
+};
+
+&pcie2 {
+ status = "okay";
+ perst-gpios = <&tlmm 114 GPIO_ACTIVE_LOW>;
+ vdda-supply = <&vreg_l28a_0p925>;
+};
+
+&pcie_phy {
+ status = "okay";
+
+ vdda-phy-supply = <&vreg_l28a_0p925>;
+ vdda-pll-supply = <&vreg_l12a_1p8>;
+};
+
+&pm8994_gpios {
+ gpio-line-names =
+ "NC",
+ "KEY_VOLP_N",
+ "NC",
+ "BL1_PWM",
+ "GPIO-F", /* BL0_PWM, LSEC pin 28 */
+ "BL1_EN",
+ "NC",
+ "WLAN_EN",
+ "NC",
+ "NC",
+ "NC",
+ "NC",
+ "NC",
+ "NC",
+ "DIVCLK1",
+ "DIVCLK2",
+ "DIVCLK3",
+ "DIVCLK4",
+ "BT_EN",
+ "PMIC_SLB",
+ "PMIC_BUA",
+ "USB_VBUS_DET";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&ls_exp_gpio_f &bt_en_gpios>;
+
+ ls_exp_gpio_f: pm8994-gpio5-state {
+ pinconf {
+ pins = "gpio5";
+ function = PMIC_GPIO_FUNC_NORMAL;
+ output-low;
+ power-source = <PM8994_GPIO_S4>; /* 1.8V */
+ };
+ };
+
+ bt_en_gpios: bt-en-pios-state {
+ pinconf {
+ pins = "gpio19";
+ function = PMIC_GPIO_FUNC_NORMAL;
+ output-low;
+ power-source = <PM8994_GPIO_S4>; /* 1.8V */
+ qcom,drive-strength = <PMIC_GPIO_STRENGTH_LOW>;
+ bias-pull-down;
+ };
+ };
+
+ wlan_en_gpios: wlan-en-gpios-state {
+ pinconf {
+ pins = "gpio8";
+ function = PMIC_GPIO_FUNC_NORMAL;
+ output-low;
+ power-source = <PM8994_GPIO_S4>; /* 1.8V */
+ qcom,drive-strength = <PMIC_GPIO_STRENGTH_LOW>;
+ bias-pull-down;
+ };
+ };
+
+ audio_mclk: clk-div1-state {
+ pinconf {
+ pins = "gpio15";
+ function = "func1";
+ power-source = <PM8994_GPIO_S4>; /* 1.8V */
+ };
+ };
+
+ volume_up_gpio: pm8996-gpio2-state {
+ pinconf {
+ pins = "gpio2";
+ function = "normal";
+ input-enable;
+ drive-push-pull;
+ bias-pull-up;
+ qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
+ power-source = <PM8994_GPIO_S4>; /* 1.8V */
+ };
+ };
+
+ divclk4_pin_a: divclk4-state {
+ pinconf {
+ pins = "gpio18";
+ function = PMIC_GPIO_FUNC_FUNC2;
+
+ bias-disable;
+ power-source = <PM8994_GPIO_S4>;
+ };
+ };
+
+ usb3_vbus_det_gpio: pm8996-gpio22-state {
+ pinconf {
+ pins = "gpio22";
+ function = PMIC_GPIO_FUNC_NORMAL;
+ input-enable;
+ bias-pull-down;
+ qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
+ power-source = <PM8994_GPIO_S4>; /* 1.8V */
+ };
+ };
+};
+
+&pm8994_mpps {
+ gpio-line-names =
+ "VDDPX_BIAS",
+ "WIFI_LED",
+ "NC",
+ "BT_LED",
+ "PM_MPP05",
+ "PM_MPP06",
+ "PM_MPP07",
+ "NC";
+};
+
+&pm8994_spmi_regulators {
+ qcom,saw-reg = <&saw3>;
+ vdd_s11-supply = <&vph_pwr>;
+
+ s9 {
+ qcom,saw-slave;
+ };
+ s10 {
+ qcom,saw-slave;
+ };
+ s11 {
+ qcom,saw-leader;
+ regulator-name = "VDD_APCC";
+ regulator-always-on;
+ regulator-min-microvolt = <980000>;
+ regulator-max-microvolt = <980000>;
+ };
+};
+
+&pmi8994_gpios {
+ gpio-line-names =
+ "NC",
+ "SPKR_AMP_EN1",
+ "SPKR_AMP_EN2",
+ "TP61",
+ "NC",
+ "USB2_VBUS_DET",
+ "NC",
+ "NC",
+ "NC",
+ "NC";
+
+ usb2_vbus_det_gpio: pmi8996-gpio6-state {
+ pinconf {
+ pins = "gpio6";
+ function = PMIC_GPIO_FUNC_NORMAL;
+ input-enable;
+ bias-pull-down;
+ qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
+ power-source = <PM8994_GPIO_S4>; /* 1.8V */
+ };
+ };
+};
+
+&pmi8994_lpg {
+ qcom,power-source = <1>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pmi8994_mpp2_userled4>;
+
+ qcom,dtest = <0 0>,
+ <0 0>,
+ <0 0>,
+ <4 1>;
+
+ status = "okay";
+
+ led@1 {
+ reg = <1>;
+ color = <LED_COLOR_ID_GREEN>;
+ function = LED_FUNCTION_HEARTBEAT;
+ function-enumerator = <1>;
+
+ linux,default-trigger = "heartbeat";
+ default-state = "on";
+ };
+
+ led@2 {
+ reg = <2>;
+ color = <LED_COLOR_ID_GREEN>;
+ function = LED_FUNCTION_HEARTBEAT;
+ function-enumerator = <0>;
+ };
+
+ led@3 {
+ reg = <3>;
+ color = <LED_COLOR_ID_GREEN>;
+ function = LED_FUNCTION_HEARTBEAT;
+ function-enumerator = <2>;
+ };
+
+ led@4 {
+ reg = <4>;
+ color = <LED_COLOR_ID_GREEN>;
+ function = LED_FUNCTION_HEARTBEAT;
+ function-enumerator = <3>;
+ };
+};
+
+&pmi8994_mpps {
+ pmi8994_mpp2_userled4: mpp2-userled4-state {
+ pins = "mpp2";
+ function = "sink";
+
+ output-low;
+ qcom,dtest = <4>;
+ };
+};
+
+&pmi8994_spmi_regulators {
+ vdd_s2-supply = <&vph_pwr>;
+
+ vdd_gfx: s2 {
+ regulator-name = "VDD_GFX";
+ regulator-min-microvolt = <980000>;
+ regulator-max-microvolt = <980000>;
+ };
+};
+
+&rpm_requests {
+ regulators-0 {
+ compatible = "qcom,rpm-pm8994-regulators";
+
+ vdd_s1-supply = <&vph_pwr>;
+ vdd_s2-supply = <&vph_pwr>;
+ vdd_s3-supply = <&vph_pwr>;
+ vdd_s4-supply = <&vph_pwr>;
+ vdd_s5-supply = <&vph_pwr>;
+ vdd_s6-supply = <&vph_pwr>;
+ vdd_s7-supply = <&vph_pwr>;
+ vdd_s8-supply = <&vph_pwr>;
+ vdd_s9-supply = <&vph_pwr>;
+ vdd_s10-supply = <&vph_pwr>;
+ vdd_s11-supply = <&vph_pwr>;
+ vdd_s12-supply = <&vph_pwr>;
+ vdd_l1-supply = <&vreg_s1b_1p025>;
+ vdd_l2_l26_l28-supply = <&vreg_s3a_1p3>;
+ vdd_l3_l11-supply = <&vreg_s3a_1p3>;
+ vdd_l4_l27_l31-supply = <&vreg_s3a_1p3>;
+ vdd_l5_l7-supply = <&vreg_s5a_2p15>;
+ vdd_l6_l12_l32-supply = <&vreg_s5a_2p15>;
+ vdd_l8_l16_l30-supply = <&vph_pwr>;
+ vdd_l9_l10_l18_l22-supply = <&vph_pwr_bbyp>;
+ vdd_l13_l19_l23_l24-supply = <&vph_pwr_bbyp>;
+ vdd_l14_l15-supply = <&vreg_s5a_2p15>;
+ vdd_l17_l29-supply = <&vph_pwr_bbyp>;
+ vdd_l20_l21-supply = <&vph_pwr_bbyp>;
+ vdd_l25-supply = <&vreg_s3a_1p3>;
+ vdd_lvs1_2-supply = <&vreg_s4a_1p8>;
+
+ vreg_s3a_1p3: s3 {
+ regulator-name = "vreg_s3a_1p3";
+ regulator-min-microvolt = <1300000>;
+ regulator-max-microvolt = <1300000>;
+ };
+
+ /**
+ * 1.8v required on LS expansion
+ * for mezzanine boards
+ */
+ vreg_s4a_1p8: s4 {
+ regulator-name = "vreg_s4a_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+ vreg_s5a_2p15: s5 {
+ regulator-name = "vreg_s5a_2p15";
+ regulator-min-microvolt = <2150000>;
+ regulator-max-microvolt = <2150000>;
+ };
+ vreg_s7a_1p0: s7 {
+ regulator-name = "vreg_s7a_1p0";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <800000>;
+ };
+
+ vreg_l1a_1p0: l1 {
+ regulator-name = "vreg_l1a_1p0";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ };
+ vreg_l2a_1p25: l2 {
+ regulator-name = "vreg_l2a_1p25";
+ regulator-min-microvolt = <1250000>;
+ regulator-max-microvolt = <1250000>;
+ };
+ vreg_l3a_0p875: l3 {
+ regulator-name = "vreg_l3a_0p875";
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <850000>;
+ };
+ vreg_l4a_1p225: l4 {
+ regulator-name = "vreg_l4a_1p225";
+ regulator-min-microvolt = <1225000>;
+ regulator-max-microvolt = <1225000>;
+ };
+ vreg_l6a_1p2: l6 {
+ regulator-name = "vreg_l6a_1p2";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ };
+ vreg_l8a_1p8: l8 {
+ regulator-name = "vreg_l8a_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+ vreg_l9a_1p8: l9 {
+ regulator-name = "vreg_l9a_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+ vreg_l10a_1p8: l10 {
+ regulator-name = "vreg_l10a_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+ vreg_l11a_1p15: l11 {
+ regulator-name = "vreg_l11a_1p15";
+ regulator-min-microvolt = <1150000>;
+ regulator-max-microvolt = <1150000>;
+ };
+ vreg_l12a_1p8: l12 {
+ regulator-name = "vreg_l12a_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+ vreg_l13a_2p95: l13 {
+ regulator-name = "vreg_l13a_2p95";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2950000>;
+ };
+ vreg_l14a_1p8: l14 {
+ regulator-name = "vreg_l14a_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+ vreg_l15a_1p8: l15 {
+ regulator-name = "vreg_l15a_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+ vreg_l16a_2p7: l16 {
+ regulator-name = "vreg_l16a_2p7";
+ regulator-min-microvolt = <2700000>;
+ regulator-max-microvolt = <2700000>;
+ };
+ vreg_l17a_2p8: l17 {
+ regulator-name = "vreg_l17a_2p8";
+ regulator-min-microvolt = <2500000>;
+ regulator-max-microvolt = <2500000>;
+ };
+ vreg_l18a_2p85: l18 {
+ regulator-name = "vreg_l18a_2p85";
+ regulator-min-microvolt = <2700000>;
+ regulator-max-microvolt = <2900000>;
+ };
+ vreg_l19a_2p8: l19 {
+ regulator-name = "vreg_l19a_2p8";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ };
+ vreg_l20a_2p95: l20 {
+ regulator-name = "vreg_l20a_2p95";
+ regulator-min-microvolt = <2950000>;
+ regulator-max-microvolt = <2950000>;
+ regulator-allow-set-load;
+ };
+ vreg_l21a_2p95: l21 {
+ regulator-name = "vreg_l21a_2p95";
+ regulator-min-microvolt = <2950000>;
+ regulator-max-microvolt = <2950000>;
+ regulator-allow-set-load;
+ regulator-system-load = <200000>;
+ };
+ vreg_l22a_3p0: l22 {
+ regulator-name = "vreg_l22a_3p0";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+ vreg_l23a_2p8: l23 {
+ regulator-name = "vreg_l23a_2p8";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ };
+ vreg_l24a_3p075: l24 {
+ regulator-name = "vreg_l24a_3p075";
+ regulator-min-microvolt = <3075000>;
+ regulator-max-microvolt = <3075000>;
+ };
+ vreg_l25a_1p2: l25 {
+ regulator-name = "vreg_l25a_1p2";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-allow-set-load;
+ };
+ vreg_l26a_0p8: l27 {
+ regulator-name = "vreg_l26a_0p8";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ };
+ vreg_l28a_0p925: l28 {
+ regulator-name = "vreg_l28a_0p925";
+ regulator-min-microvolt = <925000>;
+ regulator-max-microvolt = <925000>;
+ regulator-allow-set-load;
+ };
+ vreg_l29a_2p8: l29 {
+ regulator-name = "vreg_l29a_2p8";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ };
+ vreg_l30a_1p8: l30 {
+ regulator-name = "vreg_l30a_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+ vreg_l32a_1p8: l32 {
+ regulator-name = "vreg_l32a_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ vreg_lvs1a_1p8: lvs1 {
+ regulator-name = "vreg_lvs1a_1p8";
+ };
+
+ vreg_lvs2a_1p8: lvs2 {
+ regulator-name = "vreg_lvs2a_1p8";
+ };
+ };
+
+ regulators-1 {
+ compatible = "qcom,rpm-pmi8994-regulators";
+
+ vdd_s1-supply = <&vph_pwr>;
+ vdd_s2-supply = <&vph_pwr>;
+ vdd_s3-supply = <&vph_pwr>;
+ vdd_bst_byp-supply = <&vph_pwr>;
+
+ vph_pwr_bbyp: boost-bypass {
+ regulator-name = "vph_pwr_bbyp";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ vreg_s1b_1p025: s1 {
+ regulator-name = "vreg_s1b_1p025";
+ regulator-min-microvolt = <1025000>;
+ regulator-max-microvolt = <1025000>;
+ };
+ };
+};
+
+&sdhc2 {
+ /* External SD card */
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&sdc2_state_on &sdc2_cd_on>;
+ pinctrl-1 = <&sdc2_state_off &sdc2_cd_off>;
+ cd-gpios = <&tlmm 38 GPIO_ACTIVE_LOW>;
+ vmmc-supply = <&vreg_l21a_2p95>;
+ vqmmc-supply = <&vreg_l13a_2p95>;
+ status = "okay";
+};
+
+&q6asmdai {
+ dai@0 {
+ reg = <MSM_FRONTEND_DAI_MULTIMEDIA1>;
+ };
+
+ dai@1 {
+ reg = <MSM_FRONTEND_DAI_MULTIMEDIA2>;
+ };
+
+ dai@2 {
+ reg = <MSM_FRONTEND_DAI_MULTIMEDIA3>;
+ };
+};
+
+&slim_msm {
+ status = "okay";
+
+ slim@1 {
+ reg = <1>;
+ #address-cells = <2>;
+ #size-cells = <0>;
+
+ tasha_ifd: tas-ifd@0,0 {
+ compatible = "slim217,1a0";
+ reg = <0 0>;
+ };
+
+ wcd9335: codec@1,0 {
+ compatible = "slim217,1a0";
+ reg = <1 0>;
+
+ clock-names = "mclk", "slimbus";
+ clocks = <&div1_mclk>,
+ <&rpmcc RPM_SMD_BB_CLK1>;
+ interrupt-parent = <&tlmm>;
+ interrupts = <54 IRQ_TYPE_LEVEL_HIGH>,
+ <53 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "intr1", "intr2";
+ interrupt-controller;
+ #interrupt-cells = <1>;
+
+ pinctrl-0 = <&cdc_reset_active &wcd_intr_default>;
+ pinctrl-names = "default";
+
+ reset-gpios = <&tlmm 64 GPIO_ACTIVE_LOW>;
+ slim-ifc-dev = <&tasha_ifd>;
+
+ #sound-dai-cells = <1>;
+
+ vdd-buck-supply = <&vreg_s4a_1p8>;
+ vdd-buck-sido-supply = <&vreg_s4a_1p8>;
+ vdd-tx-supply = <&vreg_s4a_1p8>;
+ vdd-rx-supply = <&vreg_s4a_1p8>;
+ vdd-io-supply = <&vreg_s4a_1p8>;
+ };
+ };
+};
+
+&sound {
+ compatible = "qcom,apq8096-sndcard";
+ model = "DB820c";
+ audio-routing = "RX_BIAS", "MCLK";
+
+ mm1-dai-link {
+ link-name = "MultiMedia1";
+ cpu {
+ sound-dai = <&q6asmdai MSM_FRONTEND_DAI_MULTIMEDIA1>;
+ };
+ };
+
+ mm2-dai-link {
+ link-name = "MultiMedia2";
+ cpu {
+ sound-dai = <&q6asmdai MSM_FRONTEND_DAI_MULTIMEDIA2>;
+ };
+ };
+
+ mm3-dai-link {
+ link-name = "MultiMedia3";
+ cpu {
+ sound-dai = <&q6asmdai MSM_FRONTEND_DAI_MULTIMEDIA3>;
+ };
+ };
+
+ hdmi-dai-link {
+ link-name = "HDMI";
+ cpu {
+ sound-dai = <&q6afedai HDMI_RX>;
+ };
+
+ platform {
+ sound-dai = <&q6routing>;
+ };
+
+ codec {
+ sound-dai = <&mdss_hdmi 0>;
+ };
+ };
+
+ slim-dai-link {
+ link-name = "SLIM Playback";
+ cpu {
+ sound-dai = <&q6afedai SLIMBUS_6_RX>;
+ };
+
+ platform {
+ sound-dai = <&q6routing>;
+ };
+
+ codec {
+ sound-dai = <&wcd9335 AIF4_PB>;
+ };
+ };
+
+ slimcap-dai-link {
+ link-name = "SLIM Capture";
+ cpu {
+ sound-dai = <&q6afedai SLIMBUS_0_TX>;
+ };
+
+ platform {
+ sound-dai = <&q6routing>;
+ };
+
+ codec {
+ sound-dai = <&wcd9335 AIF1_CAP>;
+ };
+ };
+};
+
+&ufsphy {
+ status = "okay";
+
+ vdda-phy-supply = <&vreg_l28a_0p925>;
+ vdda-pll-supply = <&vreg_l12a_1p8>;
+};
+
+&ufshc {
+ status = "okay";
+
+ vcc-supply = <&vreg_l20a_2p95>;
+ vccq-supply = <&vreg_l25a_1p2>;
+ vccq2-supply = <&vreg_s4a_1p8>;
+ vdd-hba-supply = <&vreg_l25a_1p2>;
+
+ vcc-max-microamp = <600000>;
+ vccq-max-microamp = <450000>;
+ vccq2-max-microamp = <450000>;
+};
+
+&usb2 {
+ status = "okay";
+ extcon = <&usb2_id>;
+};
+
+&usb2_dwc3 {
+ extcon = <&usb2_id>;
+ dr_mode = "otg";
+ maximum-speed = "high-speed";
+};
+
+&usb3 {
+ status = "okay";
+ extcon = <&usb3_id>;
+};
+
+&usb3_dwc3 {
+ extcon = <&usb3_id>;
+ dr_mode = "otg";
+};
+
+&usb3phy {
+ status = "okay";
+
+ vdda-phy-supply = <&vreg_l28a_0p925>;
+ vdda-pll-supply = <&vreg_l12a_1p8>;
+};
+
+&venus {
+ status = "okay";
+};
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (c) Qualcomm Technologies, Inc. and/or its subsidiaries.
+ */
+
+/dts-v1/;
+
+#include "msm8996pro.dtsi"
+#include "apq8096-db820c.dtsi"
+
+/ {
+ model = "Qualcomm Technologies, Inc. DB820c";
+ compatible = "arrow,apq8096sg-db820c", "arrow,apq8096-db820c",
+ "qcom,apq8096-sbc", "qcom,apq8096sg", "qcom,apq8096";
+};
projects / thirdparty / kernel / linux.git / commitdiff
