From: Mikhail Zhilkin Date: Sun, 13 Apr 2025 07:02:53 +0000 (+0000) Subject: mediatek: add support for Routerich AX3000 v1 X-Git-Tag: v24.10.2~96 X-Git-Url: http://git.ipfire.org/gitweb/?a=commitdiff_plain;h=refs%2Fpull%2F18601%2Fhead;p=thirdparty%2Fopenwrt.git mediatek: add support for Routerich AX3000 v1 Routerich AX3000 v1 is a wireless WiFi 6 router. Specification ------------- - SoC : MediaTek MT7981BA dual-core ARM Cortex-A53 1.3 GHz - RAM : DDR3 512 MiB - Flash : SPI-NAND 128 MiB (Winbond) - WLAN : MediaTek MT7976CN dual-band WiFi 6 - 2.4 GHz : b/g/n/ax, MIMO 2x2 - 5 GHz : a/n/ac/ax, MIMO 2x2 - Ethernet : 10/100/1000 Mbps x3, LAN (MediaTek MT7531AE) 10/100/1000 Mbps x1, WAN (MT7981 internal PHY) - USB : 1x 3.0 with power control - UART : through-hole on PCB - [J500] GND, TX, RX, 3.3V (115200n8) - Buttons : Mesh, Reset - LEDs : 1x Power (Blue) 1x WiFi 2.4 GHz (Blue) 1x WiFi 5 GHz (Red) 1x Mesh (Blue) 3x LAN activity (Blue) 1x WAN activity (Blue) 1x WAN no-internet (Red) - Power : 12 VDC, 1.5 A Installation ------------ Flash OpenWrt 'sysupgrade.bin' image using stock firmware web-interface (without keeping settings). Return to stock --------------- Install stock firmware image (without keeping settings) using OpenWrt sysupgrade method. Recovery -------- Connect uart, use u-boot menu to flash stock firmware image or boot OpenWrt initramfs image. MAC addresses ------------- +---------+-------------------+-----------+ | | MAC | Algorithm | +---------+-------------------+-----------+ | WAN | 24:0f:5e:xx:xx:08 | label | | LAN | 24:0f:5e:xx:xx:09 | label+1 | | WLAN 2g | 24:0f:5e:xx:xx:0a | label+2 | | WLAN 5g | 24:0f:5e:xx:xx:0b | label+3 | +---------+-------------------+-----------+ The WLAN 2g MAC was found in 'Factory', 0x4 Signed-off-by: Mikhail Zhilkin (cherry picked from commit fdb6962f20aaaa703ce91338f5efcc1d055677c8) [fix merging conflict in mediatek_filogic, 01_leds, 02_network] Signed-off-by: Mikhail Zhilkin Link: https://github.com/openwrt/openwrt/pull/18601 Signed-off-by: Hauke Mehrtens --- diff --git a/package/boot/uboot-envtools/files/mediatek_filogic b/package/boot/uboot-envtools/files/mediatek_filogic index 5f586047f57..0da869cdbf9 100644 --- a/package/boot/uboot-envtools/files/mediatek_filogic +++ b/package/boot/uboot-envtools/files/mediatek_filogic @@ -111,6 +111,7 @@ glinet,gl-mt3000) mercusys,mr80x-v3|\ mercusys,mr90x-v1|\ routerich,ax3000|\ +routerich,ax3000-v1|\ tplink,re6000xd) local envdev=/dev/mtd$(find_mtd_index "u-boot-env") ubootenv_add_uci_config "$envdev" "0x0" "0x20000" "0x20000" "1" diff --git a/target/linux/mediatek/dts/mt7981b-routerich-ax3000-v1.dts b/target/linux/mediatek/dts/mt7981b-routerich-ax3000-v1.dts new file mode 100644 index 00000000000..09c555b73c0 --- /dev/null +++ b/target/linux/mediatek/dts/mt7981b-routerich-ax3000-v1.dts @@ -0,0 +1,337 @@ +// SPDX-License-Identifier: GPL-2.0-only OR MIT + +/dts-v1/; +#include +#include +#include + +#include "mt7981.dtsi" + +/ { + model = "Routerich AX3000 v1"; + compatible = "routerich,ax3000-v1", "mediatek,mt7981"; + + aliases { + label-mac-device = &gmac1; + + led-boot = &led_power_blue; + led-failsafe = &led_power_blue; + led-running = &led_power_blue; + led-upgrade = &led_power_blue; + + serial0 = &uart0; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + gpio-export { + compatible = "gpio-export"; + + gpio-0 { + gpio-export,name = "usb-enable"; + gpio-export,output = <1>; + gpios = <&pio 14 GPIO_ACTIVE_HIGH>; + }; + }; + + gpio-keys { + compatible = "gpio-keys"; + + button-0 { + label = "mesh"; + /* Reassigned to RF_KILL */ + linux,code = ; + gpios = <&pio 0 GPIO_ACTIVE_LOW>; + debounce-interval = <60>; + }; + + button-1 { + label = "reset"; + gpios = <&pio 1 GPIO_ACTIVE_LOW>; + linux,code = ; + debounce-interval = <60>; + }; + }; + + leds { + compatible = "gpio-leds"; + + led-0 { + color = ; + function = LED_FUNCTION_WLAN_5GHZ; + gpios = <&pio 5 GPIO_ACTIVE_LOW>; + linux,default-trigger = "phy1tpt"; + }; + + led-1 { + color = ; + function = LED_FUNCTION_WAN; + gpios = <&pio 6 GPIO_ACTIVE_HIGH>; + }; + + led_power_blue: led-2 { + color = ; + function = LED_FUNCTION_POWER; + gpios = <&pio 7 GPIO_ACTIVE_LOW>; + }; + + led-3 { + color = ; + function = LED_FUNCTION_LAN; + function-enumerator = <1>; + gpios = <&pio 9 GPIO_ACTIVE_LOW>; + }; + + led-4 { + color = ; + function = LED_FUNCTION_LAN; + function-enumerator = <2>; + gpios = <&pio 10 GPIO_ACTIVE_LOW>; + }; + + led-5 { + color = ; + function = LED_FUNCTION_LAN; + function-enumerator = <3>; + gpios = <&pio 11 GPIO_ACTIVE_LOW>; + }; + + led-6 { + color = ; + function = LED_FUNCTION_WAN; + gpios = <&pio 12 GPIO_ACTIVE_LOW>; + }; + + led-7 { + color = ; + function = LED_FUNCTION_WLAN_2GHZ; + gpios = <&pio 34 GPIO_ACTIVE_LOW>; + linux,default-trigger = "phy0tpt"; + }; + + led-8 { + color = ; + /* LED_FUNCTION_MESH isn't implemented yet */ + function = "mesh"; + gpios = <&pio 35 GPIO_ACTIVE_LOW>; + }; + }; +}; + +ð { + status = "okay"; + + gmac0: mac@0 { + compatible = "mediatek,eth-mac"; + reg = <0>; + phy-mode = "2500base-x"; + + nvmem-cell-names = "mac-address"; + nvmem-cells = <&macaddr_factory_4 (-1)>; + + fixed-link { + speed = <2500>; + full-duplex; + pause; + }; + }; + + gmac1: mac@1 { + compatible = "mediatek,eth-mac"; + reg = <1>; + phy-mode = "gmii"; + phy-handle = <&int_gbe_phy>; + + nvmem-cell-names = "mac-address"; + nvmem-cells = <&macaddr_factory_4 (-2)>; + }; +}; + +&mdio_bus { + switch: switch@1f { + compatible = "mediatek,mt7531"; + reg = <0x1f>; + reset-gpios = <&pio 39 GPIO_ACTIVE_HIGH>; + interrupt-controller; + #interrupt-cells = <1>; + interrupt-parent = <&pio>; + interrupts = <38 IRQ_TYPE_LEVEL_HIGH>; + }; +}; + +&spi0 { + pinctrl-names = "default"; + pinctrl-0 = <&spi0_flash_pins>; + status = "okay"; + + spi_nand@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "spi-nand"; + reg = <0>; + + spi-max-frequency = <52000000>; + spi-tx-buswidth = <4>; + spi-rx-buswidth = <4>; + + spi-cal-enable; + spi-cal-mode = "read-data"; + spi-cal-datalen = <7>; + spi-cal-data = /bits/ 8 <0x53 0x50 0x49 0x4e 0x41 0x4e 0x44>; + spi-cal-addrlen = <5>; + spi-cal-addr = /bits/ 32 <0x0 0x0 0x0 0x0 0x0>; + + mediatek,nmbm; + mediatek,bmt-max-ratio = <1>; + mediatek,bmt-max-reserved-blocks = <64>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0_all { + label = "spi0.0"; + reg = <0x0 0x8000000>; + read-only; + }; + + partition@0 { + label = "BL2"; + reg = <0x0 0x100000>; + read-only; + }; + + partition@100000 { + label = "u-boot-env"; + reg = <0x100000 0x80000>; + }; + + partition@180000 { + label = "Factory"; + reg = <0x180000 0x200000>; + read-only; + + nvmem-layout { + compatible = "fixed-layout"; + #address-cells = <1>; + #size-cells = <1>; + + eeprom_factory_0: eeprom@0 { + reg = <0x0 0x1000>; + }; + + macaddr_factory_4: macaddr@4 { + compatible = "mac-base"; + reg = <0x4 0x6>; + #nvmem-cell-cells = <1>; + }; + }; + }; + + partition@380000 { + label = "FIP"; + reg = <0x380000 0x200000>; + read-only; + }; + + partition@580000 { + label = "ubi"; + reg = <0x580000 0x7000000>; + }; + }; + }; +}; + +&switch { + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@1 { + reg = <1>; + label = "lan1"; + }; + + port@2 { + reg = <2>; + label = "lan2"; + }; + + port@3 { + reg = <3>; + label = "lan3"; + }; + + port@6 { + reg = <6>; + ethernet = <&gmac0>; + phy-mode = "2500base-x"; + + fixed-link { + speed = <2500>; + full-duplex; + pause; + }; + }; + }; +}; + +&pio { + spi0_flash_pins: spi0-pins { + mux { + function = "spi"; + groups = "spi0", "spi0_wp_hold"; + }; + + conf-pu { + pins = "SPI0_CS", "SPI0_HOLD", "SPI0_WP"; + drive-strength = ; + bias-pull-up = ; + }; + + conf-pd { + pins = "SPI0_CLK", "SPI0_MOSI", "SPI0_MISO"; + drive-strength = ; + bias-pull-down = ; + }; + }; +}; + +&uart0 { + status = "okay"; +}; + +&usb_phy { + status = "okay"; +}; + +&watchdog { + status = "okay"; +}; + +&wifi { + status = "okay"; + nvmem-cell-names = "eeprom"; + nvmem-cells = <&eeprom_factory_0>; + + ieee80211-freq-limit = <2400000 2500000>, <5170000 5835000>; + + band@0 { + reg = <0>; + nvmem-cells = <&macaddr_factory_4 (0)>; + nvmem-cell-names = "mac-address"; + }; + + band@1 { + reg = <1>; + nvmem-cells = <&macaddr_factory_4 (1)>; + nvmem-cell-names = "mac-address"; + }; +}; + +&xhci { + status = "okay"; +}; diff --git a/target/linux/mediatek/filogic/base-files/etc/board.d/01_leds b/target/linux/mediatek/filogic/base-files/etc/board.d/01_leds index aaefa1cb561..dd0bc3597bb 100644 --- a/target/linux/mediatek/filogic/base-files/etc/board.d/01_leds +++ b/target/linux/mediatek/filogic/base-files/etc/board.d/01_leds @@ -98,6 +98,13 @@ routerich,ax3000-ubootmod) ucidef_set_led_netdev "wan" "wan" "blue:wan" "wan" "link tx rx" ucidef_set_led_netdev "wan-off" "wan-off" "red:wan" "wan" "link" ;; +routerich,ax3000-v1) + ucidef_set_led_netdev "lan-1" "lan-1" "blue:lan-1" "lan1" "link tx rx" + ucidef_set_led_netdev "lan-2" "lan-2" "blue:lan-2" "lan2" "link tx rx" + ucidef_set_led_netdev "lan-3" "lan-3" "blue:lan-3" "lan3" "link tx rx" + ucidef_set_led_netdev "wan" "wan" "blue:wan" "eth1" "link tx rx" + ucidef_set_led_netdev "wan-off" "wan-off" "red:wan" "eth1" "link" + ;; smartrg,sdg-8733|\ smartrg,sdg-8734) ucidef_set_led_netdev "lan-1-green" "LAN1" "mdio-bus:08:green:lan" "lan1" "link_2500 link_5000" diff --git a/target/linux/mediatek/filogic/base-files/etc/board.d/02_network b/target/linux/mediatek/filogic/base-files/etc/board.d/02_network index 3d7cdd156ae..3440cae0195 100644 --- a/target/linux/mediatek/filogic/base-files/etc/board.d/02_network +++ b/target/linux/mediatek/filogic/base-files/etc/board.d/02_network @@ -14,6 +14,7 @@ mediatek_setup_interfaces() netis,nx31|\ nokia,ea0326gmp|\ mercusys,mr80x-v3|\ + routerich,ax3000-v1|\ zbtlink,zbt-z8103ax) ucidef_set_interfaces_lan_wan "lan1 lan2 lan3" eth1 ;; diff --git a/target/linux/mediatek/image/filogic.mk b/target/linux/mediatek/image/filogic.mk index 733f026a46b..9aa0cf9c04b 100644 --- a/target/linux/mediatek/image/filogic.mk +++ b/target/linux/mediatek/image/filogic.mk @@ -1481,6 +1481,18 @@ define Device/routerich_ax3000-ubootmod endef TARGET_DEVICES += routerich_ax3000-ubootmod +define Device/routerich_ax3000-v1 + DEVICE_VENDOR := Routerich + DEVICE_MODEL := AX3000 + DEVICE_VARIANT := v1 + DEVICE_DTS := mt7981b-routerich-ax3000-v1 + DEVICE_DTS_DIR := ../dts + DEVICE_PACKAGES := kmod-mt7915e kmod-mt7981-firmware kmod-usb3 mt7981-wo-firmware + IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata + SUPPORTED_DEVICES += mediatek,mt7981-spim-snand-rfb +endef +TARGET_DEVICES += routerich_ax3000-v1 + define Device/ruijie_rg-x60-pro DEVICE_VENDOR := Ruijie DEVICE_MODEL := RG-X60 Pro