Bit 4: ClockEnSet the ClockEn bit high to enable an external clocking
(crystal or clock generator at XIN). Set the ClockEn bit to 0 to disable
clocking
Bit 1: CrystalEnSet the CrystalEn bit high to enable the crystal
oscillator. When using an external clock source at XIN, CrystalEn must
be set low.
The bit 4, MAX310X_CLKSRC_EXTCLK_BIT, should be set and was not.
This was required to make the MAX3107 with an external crystal on our
board able to send or receive data.
When the tty layer requests the uart to throttle, the current code
executing in msm_serial will trigger "Bad mode in Error Handler" and
generate an invalid stack frame in pstore before rebooting (that is if
pstore is indeed configured: otherwise the user shall just notice a
reboot with no further information dumped to the console).
This patch replaces the PIO byte accessor with the word accessor
already used in PIO mode.
For a while, we've had the problem of i2c bus access not grabbing
a runtime PM ref when it's being used in userspace by i2c-dev, resulting
in nouveau spamming the kernel log with errors if anything attempts to
access the i2c bus while the GPU is in runtime suspend. An example:
[ 130.078386] nouveau 0000:01:00.0: i2c: aux 000d: begin idle timeout ffffffff
Since the GPU is in runtime suspend, the MMIO region that the i2c bus is
on isn't accessible. On x86, the standard behavior for accessing an
unavailable MMIO region is to just return ~0.
Except, that turned out to be a lie. While computers with a clean
concious will return ~0 in this scenario, some machines will actually
completely hang a CPU on certian bad MMIO accesses. This was witnessed
with someone's Lenovo ThinkPad P50, where sensors-detect attempting to
access the i2c bus while the GPU was suspended would result in a CPU
hang:
Yikes! While I wanted to try to make it so that accessing an i2c bus on
nouveau would wake up the GPU as needed, airlied pointed out that pretty
much any usecase for userspace accessing an i2c bus on a GPU (mainly for
the DDC brightness control that some displays have) is going to only be
useful while there's at least one display enabled on the GPU anyway, and
the GPU never sleeps while there's displays running.
Since teaching the i2c bus to wake up the GPU on userspace accesses is a
good deal more difficult than it might seem, mostly due to the fact that
we have to use the i2c bus during runtime resume of the GPU, we instead
opt for the easiest solution: don't let userspace access i2c busses on
the GPU at all while it's in runtime suspend.
Changes since v1:
* Also disable i2c busses that run over DP AUX
Signed-off-by: Lyude Paul <lyude@redhat.com> Cc: stable@vger.kernel.org Signed-off-by: Ben Skeggs <bskeggs@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I measured power consumption between power_save_node=1 and power_save_node=0.
It's almost the same.
Codec will enter to runtime suspend and suspend.
That pin also will enter to D3. Don't need to enter to D3 by single pin.
So, Disable power_save_node as default. It will avoid more issues.
Windows Driver also has not this option at runtime PM.
When syncing the log, the final phase of a fsync operation, we need to
either create a log root's item or update the existing item in the log
tree of log roots, and that depends on the current value of the log
root's log_transid - if it's 1 we need to create the log root item,
otherwise it must exist already and we update it. Since there is no
synchronization between updating the log_transid and checking it for
deciding whether the log root's item needs to be created or updated, we
end up with a tiny race window that results in attempts to update the
item to fail because the item was not yet created:
CPU 1 CPU 2
btrfs_sync_log()
lock root->log_mutex
set log root's log_transid to 1
unlock root->log_mutex
btrfs_sync_log()
lock root->log_mutex
sets log root's
log_transid to 2
unlock root->log_mutex
update_log_root()
sees log root's log_transid
with a value of 2
calls btrfs_update_root(),
which fails with -EUCLEAN
and causes transaction abort
Until recently the race lead to a BUG_ON at btrfs_update_root(), but after
the recent commit 7ac1e464c4d47 ("btrfs: Don't panic when we can't find a
root key") we just abort the current transaction.
When the user tries to remove a zfcp port via sysfs, we only rejected it if
there are zfcp unit children under the port. With purely automatically
scanned LUNs there are no zfcp units but only SCSI devices. In such cases,
the port_remove erroneously continued. We close the port and this
implicitly closes all LUNs under the port. The SCSI devices survive with
their private zfcp_scsi_dev still holding a reference to the "removed"
zfcp_port (still allocated but invisible in sysfs) [zfcp_get_port_by_wwpn
in zfcp_scsi_slave_alloc]. This is not a problem as long as the fc_rport
stays blocked. Once (auto) port scan brings back the removed port, we
unblock its fc_rport again by design. However, there is no mechanism that
would recover (open) the LUNs under the port (no "ersfs_3" without
zfcp_unit [zfcp_erp_strategy_followup_success]). Any pending or new I/O to
such LUN leads to repeated:
See also v4.10 commit 6f2ce1c6af37 ("scsi: zfcp: fix rport unblock race
with LUN recovery"). Even a manual LUN recovery
(echo 0 > /sys/bus/scsi/devices/H:C:T:L/zfcp_failed)
does not help, as the LUN links to the old "removed" port which remains
to lack ZFCP_STATUS_COMMON_RUNNING [zfcp_erp_required_act].
The only workaround is to first ensure that the fc_rport is blocked
(e.g. port_remove again in case it was re-discovered by (auto) port scan),
then delete the SCSI devices, and finally re-discover by (auto) port scan.
The port scan includes an fc_rport unblock, which in turn triggers
a new scan on the scsi target to freshly get new pure auto scan LUNs.
Fix this by rejecting port_remove also if there are SCSI devices
(even without any zfcp_unit) under this port. Re-use mechanics from v3.7
commit d99b601b6338 ("[SCSI] zfcp: restore refcount check on port_remove").
However, we have to give up zfcp_sysfs_port_units_mutex earlier in unit_add
to prevent a deadlock with scsi_host scan taking shost->scan_mutex first
and then zfcp_sysfs_port_units_mutex now in our zfcp_scsi_slave_alloc().
Signed-off-by: Steffen Maier <maier@linux.ibm.com> Fixes: b62a8d9b45b9 ("[SCSI] zfcp: Use SCSI device data zfcp scsi dev instead of zfcp unit") Fixes: f8210e34887e ("[SCSI] zfcp: Allow midlayer to scan for LUNs when running in NPIV mode") Cc: <stable@vger.kernel.org> #2.6.37+ Reviewed-by: Benjamin Block <bblock@linux.ibm.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With this early return due to zfcp_unit child(ren), we don't use the
zfcp_port reference from the earlier zfcp_get_port_by_wwpn() anymore and
need to put it.
Signed-off-by: Steffen Maier <maier@linux.ibm.com> Fixes: d99b601b6338 ("[SCSI] zfcp: restore refcount check on port_remove") Cc: <stable@vger.kernel.org> #3.7+ Reviewed-by: Jens Remus <jremus@linux.ibm.com> Reviewed-by: Benjamin Block <bblock@linux.ibm.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Most Siano devices require an alignment for the response.
Changeset f3be52b0056a ("media: usb: siano: Fix general protection fault in smsusb")
changed the logic with gets such aligment, but it now produces a
sparce warning:
drivers/media/usb/siano/smsusb.c: In function 'smsusb_init_device':
drivers/media/usb/siano/smsusb.c:447:37: warning: 'in_maxp' may be used uninitialized in this function [-Wmaybe-uninitialized]
447 | dev->response_alignment = in_maxp - sizeof(struct sms_msg_hdr);
| ~~~~~~~~^~~~~~~~~~~~~~~~~~~~~~~~~~~~
The sparse message itself is bogus, but a broken (or fake) USB
eeprom could produce a negative value for response_alignment.
So, change the code in order to check if the result is not
negative.
GCC complains about an apparently uninitialized variable recently
added to smsusb_init_device(). It's a false positive, but to silence
the warning this patch adds a trivial initialization.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Reported-by: kbuild test robot <lkp@intel.com> CC: <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The syzkaller USB fuzzer found a general-protection-fault bug in the
smsusb part of the Siano DVB driver. The fault occurs during probe
because the driver assumes without checking that the device has both
IN and OUT endpoints and the IN endpoint is ep1.
By slightly rearranging the driver's initialization code, we can make
the appropriate checks early on and thus avoid the problem. If the
expected endpoints aren't present, the new code safely returns -ENODEV
from the probe routine.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Reported-and-tested-by: syzbot+53f029db71c19a47325a@syzkaller.appspotmail.com CC: <stable@vger.kernel.org> Reviewed-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The syzkaller USB fuzzer found a slab-out-of-bounds write bug in the
USB core, caused by a failure to check the actual size of a BOS
descriptor. This patch adds a check to make sure the descriptor is at
least as large as it is supposed to be, so that the code doesn't
inadvertently access memory beyond the end of the allocated region
when assigning to dev->bos->desc->bNumDeviceCaps later on.
drivers/usb/usbip/stub_dev.c:399:9: sparse: sparse: context imbalance in 'stub_probe' - different lock contexts for basic block
drivers/usb/usbip/stub_dev.c:418:13: sparse: sparse: context imbalance in 'stub_disconnect' - different lock contexts for basic block
drivers/usb/usbip/stub_dev.c:464:1-10: second lock on line 476
stub_probe() and stub_disconnect() call functions which could call
sleeping function in invalid context whil holding busid_lock.
Fix the problem by refining the lock holds to short critical sections
to change the busid_priv fields. This fix restructures the code to
limit the lock holds in stub_probe() and stub_disconnect().
With defective USB sticks we see the following error happen:
usb 1-3: new high-speed USB device number 6 using xhci_hcd
usb 1-3: device descriptor read/64, error -71
usb 1-3: device descriptor read/64, error -71
usb 1-3: new high-speed USB device number 7 using xhci_hcd
usb 1-3: device descriptor read/64, error -71
usb 1-3: unable to get BOS descriptor set
usb 1-3: New USB device found, idVendor=0781, idProduct=5581
usb 1-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
...
BUG: unable to handle kernel NULL pointer dereference at 0000000000000008
Tracking this down shows that udev->bos is NULL in the following code:
(xhci.c, in xhci_set_usb2_hardware_lpm)
field = le32_to_cpu(udev->bos->ext_cap->bmAttributes); <<<<<<< here
if (enable) {
/* Host supports BESL timeout instead of HIRD */
if (udev->usb2_hw_lpm_besl_capable) {
/* if device doesn't have a preferred BESL value use a
* default one which works with mixed HIRD and BESL
* systems. See XHCI_DEFAULT_BESL definition in xhci.h
*/
if ((field & USB_BESL_SUPPORT) &&
(field & USB_BESL_BASELINE_VALID))
hird = USB_GET_BESL_BASELINE(field);
else
hird = udev->l1_params.besl;
The failing case is when disabling LPM. So it is sufficient to avoid
access to udev->bos by moving the instruction into the "enable" clause.
Xhci_handshake() implements the algorithm already captured by
readl_poll_timeout_atomic(). Convert the former to use the latter to
avoid repetition.
Turned out this patch also fixes a bug on the AMD Stoneyridge platform
where usleep(1) sometimes takes over 10ms.
This means a 5 second timeout can easily take over 15 seconds which will
trigger the watchdog and reboot the system.
[Add info about patch fixing a bug to commit message -Mathias] Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com> Tested-by: Raul E Rangel <rrangel@chromium.org> Reviewed-by: Raul E Rangel <rrangel@chromium.org> Cc: <stable@vger.kernel.org> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 597c56e372da ("xhci: update bounce buffer with correct sg num")
caused the following build warnings:
drivers/usb/host/xhci-ring.c:676:19: warning: format '%ld' expects argument of type 'long int', but argument 3 has type 'size_t {aka unsigned int}' [-Wformat=]
Use %zu for printing size_t type in order to fix the warnings.
This change fixes a data corruption issue occurred on USB hard disk for
the case that bounce buffer is used during transferring data.
While updating data between sg list and bounce buffer, current
implementation passes mapped sg number (urb->num_mapped_sgs) to
sg_pcopy_from_buffer() and sg_pcopy_to_buffer(). This causes data
not get copied if target buffer is located in the elements after
mapped sg elements. This change passes sg number for full list to
fix issue.
Besides, for copying data from bounce buffer, calling dma_unmap_single()
on the bounce buffer before copying data to sg list can avoid cache issue.
Fixes: f9c589e142d0 ("xhci: TD-fragment, align the unsplittable case with a bounce buffer") Cc: <stable@vger.kernel.org> # v4.8+ Signed-off-by: Henry Lin <henryl@nvidia.com> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ror32 implementation (word >> shift) | (word << (32 - shift) has
undefined behaviour if shift is outside the [1, 31] range. Similarly
for the 64 bit variants. Most callers pass a compile-time constant
(naturally in that range), but there's an UBSAN report that these may
actually be called with a shift count of 0.
Instead of special-casing that, we can make them DTRT for all values of
shift while also avoiding UB. For some reason, this was already partly
done for rol32 (which was well-defined for [0, 31]). gcc 8 recognizes
these patterns as rotates, so for example
__u32 rol32(__u32 word, unsigned int shift)
{
return (word << (shift & 31)) | (word >> ((-shift) & 31));
}
compiles to
0000000000000020 <rol32>:
20: 89 f8 mov %edi,%eax
22: 89 f1 mov %esi,%ecx
24: d3 c0 rol %cl,%eax
26: c3 retq
Older compilers unfortunately do not do as well, but this only affects
the small minority of users that don't pass constants.
Due to integer promotions, ro[lr]8 were already well-defined for shifts
in [0, 8], and ro[lr]16 were mostly well-defined for shifts in [0, 16]
(only mostly - u16 gets promoted to _signed_ int, so if bit 15 is set,
word << 16 is undefined). For consistency, update those as well.
Previously, %g2 would end up with the value PAGE_SIZE, but after the
commit mentioned below it ends up with the value 1 due to being reused
for a different purpose. We need it to be PAGE_SIZE as we use it to step
through pages in our demap loop, otherwise we set different flags in the
low 12 bits of the address written to, thereby doing things other than a
nucleus page flush.
Fixes: a74ad5e660a9 ("sparc64: Handle extremely large kernel TLB range flushes more gracefully.") Reported-by: Meelis Roos <mroos@linux.ee> Tested-by: Meelis Roos <mroos@linux.ee> Signed-off-by: James Clarke <jrtc27@jrtc27.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Error message printed:
modprobe: ERROR: could not insert 'tipc': Address family not
supported by protocol.
when modprobe tipc after the following patch: switch order of
device registration, commit 7e27e8d6130c
("tipc: switch order of device registration to fix a crash")
Because sock_create_kern(net, AF_TIPC, ...) called by
tipc_topsrv_create_listener() in the initialization process
of tipc_init_net(), so tipc_socket_init() must be execute before that.
Meanwhile, tipc_net_id need to be initialized when sock_create()
called, and tipc_socket_init() is no need to be called for each namespace.
I add a variable tipc_topsrv_net_ops, and split the
register_pernet_subsys() of tipc into two parts, and split
tipc_socket_init() with initialization of pernet params.
By the way, I fixed resources rollback error when tipc_bcast_init()
failed in tipc_init_net().
Fixes: 7e27e8d6130c ("tipc: switch order of device registration to fix a crash") Signed-off-by: Junwei Hu <hujunwei4@huawei.com> Reported-by: Wang Wang <wangwang2@huawei.com> Reported-by: syzbot+1e8114b61079bfe9cbc5@syzkaller.appspotmail.com Reviewed-by: Kang Zhou <zhoukang7@huawei.com> Reviewed-by: Suanming Mou <mousuanming@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no need for this at all. Worst it means that if
the guest tries to write to BARs it could lead (on certain
platforms) to PCI SERR errors.
Please note that with af6fc858a35b90e89ea7a7ee58e66628c55c776b
"xen-pciback: limit guest control of command register"
a guest is still allowed to enable those control bits (safely), but
is not allowed to disable them and that therefore a well behaved
frontend which enables things before using them will still
function correctly.
This is done via an write to the configuration register 0x4 which
triggers on the backend side:
command_write
\- pci_enable_device
\- pci_enable_device_flags
\- do_pci_enable_device
\- pcibios_enable_device
\-pci_enable_resourcess
[which enables the PCI_COMMAND_MEMORY|PCI_COMMAND_IO]
However guests (and drivers) which don't do this could cause
problems, including the security issues which XSA-120 sought
to address.
Reported-by: Jan Beulich <jbeulich@suse.com> Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Reviewed-by: Prarit Bhargava <prarit@redhat.com> Signed-off-by: Juergen Gross <jgross@suse.com> Cc: Ben Hutchings <ben.hutchings@codethink.co.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
VMX ghash was using a fallback that did not support interleaving simd
and nosimd operations, leading to failures in the extended test suite.
If I understood correctly, Eric's suggestion was to use the same
data format that the generic code uses, allowing us to call into it
with the same contexts. I wasn't able to get that to work - I think
there's a very different key structure and data layout being used.
So instead steal the arm64 approach and perform the fallback
operations directly if required.
Fixes: cc333cd68dfa ("crypto: vmx - Adding GHASH routines for VMX module") Cc: stable@vger.kernel.org # v4.1+ Reported-by: Eric Biggers <ebiggers@google.com> Signed-off-by: Daniel Axtens <dja@axtens.net> Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> Tested-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Daniel Axtens <dja@axtens.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
MVPP2_TXQ_SCHED_TOKEN_CNTR_REG() expects the logical queue id but
the current code is passing the global tx queue offset, so it ends
up writing to unknown registers (between 0x8280 and 0x82fc, which
seemed to be unused by the hardware). This fixes the issue by using
the logical queue id instead.
Fixes: 3f518509dedc ("ethernet: Add new driver for Marvell Armada 375 network unit") Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix below issues in err code path of probe:
1. we don't need to unregister_netdev() because the netdev isn't
registered.
2. when register_netdev() fails, we also need to destroy bm pool for
HWBM case.
Fixes: dc35a10f68d3 ("net: mvneta: bm: add support for hardware buffer management") Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ip_sf_list_clear_all() needs to be defined even if !CONFIG_IP_MULTICAST
Fixes: 3580d04aa674 ("ipv4/igmp: fix another memory leak in igmpv3_del_delrec()") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: kbuild test robot <lkp@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes: 9c8bb163ae78 ("igmp, mld: Fix memory leak in igmpv3/mld_del_delrec()") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Hangbin Liu <liuhangbin@gmail.com> Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For every RX packet, the driver replenishes all buffers used for that
packet and puts them back into the RX ring and RX aggregation ring.
In one code path where the RX packet has one RX buffer and one or more
aggregation buffers, we missed recycling the aggregation buffer(s) if
we are unable to allocate a new SKB buffer. This leads to the
aggregation ring slowly running out of buffers over time. Fix it
by properly recycling the aggregation buffers.
Fixes: c0c050c58d84 ("bnxt_en: New Broadcom ethernet driver.") Reported-by: Rakesh Hemnani <rhemnani@fb.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Chris Packham [Mon, 20 May 2019 03:45:36 +0000 (15:45 +1200)]
tipc: Avoid copying bytes beyond the supplied data
TLV_SET is called with a data pointer and a len parameter that tells us
how many bytes are pointed to by data. When invoking memcpy() we need
to careful to only copy len bytes.
Previously we would copy TLV_LENGTH(len) bytes which would copy an extra
4 bytes past the end of the data pointer which newer GCC versions
complain about.
In file included from test.c:17:
In function 'TLV_SET',
inlined from 'test' at test.c:186:5:
/usr/include/linux/tipc_config.h:317:3:
warning: 'memcpy' forming offset [33, 36] is out of the bounds [0, 32]
of object 'bearer_name' with type 'char[32]' [-Warray-bounds]
memcpy(TLV_DATA(tlv_ptr), data, tlv_len);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
test.c: In function 'test':
test.c::161:10: note:
'bearer_name' declared here
char bearer_name[TIPC_MAX_BEARER_NAME];
^~~~~~~~~~~
We still want to ensure any padding bytes at the end are initialised, do
this with a explicit memset() rather than copy bytes past the end of
data. Apply the same logic to TCM_SET.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The crash happens roughly 125..130ms after the disconnect. This
correlates with the 'delay' timer that is started on certain USB tx/rx
errors in the URB completion handler.
The problem is a race of usbnet_stop() with usbnet_start_xmit(). In
usbnet_stop() we call usbnet_terminate_urbs() to cancel all URBs in
flight. This only makes sense if no new URBs are submitted
concurrently, though. But the usbnet_start_xmit() can run at the same
time on another CPU which almost unconditionally submits an URB. The
error callback of the new URB will then schedule the timer after it was
already stopped.
The fix adds a check if the tx queue is stopped after the tx list lock
has been taken. This should reliably prevent the submission of new URBs
while usbnet_terminate_urbs() does its job. The same thing is done on
the rx side even though it might be safe due to other flags that are
checked there.
Signed-off-by: Jan Klötzke <Jan.Kloetzke@preh.de> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 984203ceff27 ("net: stmmac: mdio: remove reset gpio free")
removed the reset gpio free, when the driver is unbinded or rmmod,
we miss the gpio free.
This patch uses managed API to request the reset gpio, so that the
gpio could be freed properly.
Fixes: 984203ceff27 ("net: stmmac: mdio: remove reset gpio free") Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a network driver provides to napi_gro_frags() an
skb with a page fragment of exactly 14 bytes, the call
to gro_pull_from_frag0() will 'consume' the fragment
by calling skb_frag_unref(skb, 0), and the page might
be freed and reused.
Reading eth->h_proto at the end of napi_frags_skb() might
read mangled data, or crash under specific debugging features.
BUG: KASAN: use-after-free in napi_frags_skb net/core/dev.c:5833 [inline]
BUG: KASAN: use-after-free in napi_gro_frags+0xc6f/0xd10 net/core/dev.c:5841
Read of size 2 at addr ffff88809366840c by task syz-executor599/8957
Fix the clk mismatch in the error path "failed_reset" because
below error path will disable clk_ahb and clk_ipg directly, it
should use pm_runtime_put_noidle() instead of pm_runtime_put()
to avoid to call runtime resume callback.
Reported-by: Baruch Siach <baruch@tkos.co.il> Signed-off-by: Fugang Duan <fugang.duan@nxp.com> Tested-by: Baruch Siach <baruch@tkos.co.il> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
IPv6 does not consider if the socket is bound to a device when binding
to an address. The result is that a socket can be bound to eth0 and
then bound to the address of eth1. If the device is a VRF, the result
is that a socket can only be bound to an address in the default VRF.
Resolve by considering the device if sk_bound_dev_if is set.
Signed-off-by: Mike Manning <mmanning@vyatta.att-mail.com> Reviewed-by: David Ahern <dsahern@gmail.com> Tested-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After an event is sent, we try to copy it into the user buffer of the
first waiter in drm_read() and if the user buffer doesn't have enough
room we put it back onto the list. However, we didn't wake up any
subsequent waiter, so that event may sit on the list until either a new
vblank event is sent or a new waiter appears. Rare, but in the worst
case may lead to a stuck process.
Building with clang shows a variable that is only used by the
suspend/resume functions but defined outside of their #ifdef block:
sound/soc/ti/davinci-mcasp.c:48:12: error: variable 'context_regs' is not needed and will not be emitted
We commonly fix these by marking the PM functions as __maybe_unused,
but here that would grow the davinci_mcasp structure, so instead
add another #ifdef here.
Fixes: 1cc0c054f380 ("ASoC: davinci-mcasp: Convert the context save/restore to use array") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Reviewed-by: Nathan Chancellor <natechancellor@gmail.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
This fixes a bug for messages containing both zero length and
unidirectional xfers.
The function spi_map_msg will allocate dummy tx and/or rx buffers
for use with unidirectional transfers when the hardware can only do
a bidirectional transfer. That dummy buffer will be used in place
of a NULL buffer even when the xfer length is 0.
Then in the function __spi_map_msg, if he hardware can dma,
the zero length xfer will have spi_map_buf called on the dummy
buffer.
Eventually, __sg_alloc_table is called and returns -EINVAL
because nents == 0.
This fix prevents the error by not using the dummy buffer when
the xfer length is zero.
Signed-off-by: Chris Lesiak <chris.lesiak@licor.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
While the sequencer is reset after each SPI message since commit 880c6d114fd79a69 ("spi: rspi: Add support for Quad and Dual SPI
Transfers on QSPI"), it was never reset for the first message, thus
relying on reset state or bootloader settings.
Fix this by initializing it explicitly during configuration.
Fixes: 0b2182ddac4b8837 ("spi: add support for Renesas RSPI") Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
pch_alloc_dma_buf allocated tx, rx DMA buffers which can fail. Further,
these buffers are used without a check. The patch checks for these
failures and sends the error upstream.
Signed-off-by: Aditya Pakki <pakki001@umn.edu> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
During debug, it was seen that the driver is issuing commands specific to
SLI3 on SLI4 devices. Although the adapter correctly rejected the command,
this should not be done.
Revise the code to stop sending these commands on a SLI4 adapter.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <jsmart2021@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Two saa7146/hexium files contain a construct that causes a warning
when built with clang:
drivers/media/pci/saa7146/hexium_orion.c:210:12: error: stack frame size of 2272 bytes in function 'hexium_probe'
[-Werror,-Wframe-larger-than=]
static int hexium_probe(struct saa7146_dev *dev)
^
drivers/media/pci/saa7146/hexium_gemini.c:257:12: error: stack frame size of 2304 bytes in function 'hexium_attach'
[-Werror,-Wframe-larger-than=]
static int hexium_attach(struct saa7146_dev *dev, struct saa7146_pci_extension_data *info)
^
This one happens regardless of KASAN, and the problem is that a
constructor to initialize a dynamically allocated structure leads
to a copy of that structure on the stack, whereas gcc initializes
it in place.
The FDMI manufacturer value being reported on Linux is inconsistent with
other OS's.
Set the value to "Emulex Corporation" for consistency.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <jsmart2021@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
adma driver is using pm_clk_*() interface for managing clock resources.
With this it is observed that clocks remain ON always. This happens on
Tegra devices which use BPMP co-processor to manage clock resources,
where clocks are enabled during prepare phase. This is necessary because
clocks to BPMP are always blocking. When pm_clk_*() interface is used on
such Tegra devices, clock prepare count is not balanced till remove call
happens for the driver and hence clocks are seen ON always. Thus this
patch replaces pm_clk_*() with devm_clk_*() framework.
Clang -Wuninitialized notices that on is_qla40XX we never allocate any DMA
memory in get_fw_boot_info() but attempt to free it anyway:
drivers/scsi/qla4xxx/ql4_os.c:5915:7: error: variable 'buf_dma' is used uninitialized whenever 'if' condition is false
[-Werror,-Wsometimes-uninitialized]
if (!(val & 0x07)) {
^~~~~~~~~~~~~
drivers/scsi/qla4xxx/ql4_os.c:5985:47: note: uninitialized use occurs here
dma_free_coherent(&ha->pdev->dev, size, buf, buf_dma);
^~~~~~~
drivers/scsi/qla4xxx/ql4_os.c:5915:3: note: remove the 'if' if its condition is always true
if (!(val & 0x07)) {
^~~~~~~~~~~~~~~~~~~
drivers/scsi/qla4xxx/ql4_os.c:5885:20: note: initialize the variable 'buf_dma' to silence this warning
dma_addr_t buf_dma;
^
= 0
Skip the call to dma_free_coherent() here.
Fixes: 2a991c215978 ("[SCSI] qla4xxx: Boot from SAN support for open-iscsi") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Reviewed-by: Nathan Chancellor <natechancellor@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
If ohci-platform is runtime suspended, we can currently get an "imprecise
external abort" on reboot with ohci-platform loaded when PM runtime
is implemented for the SoC.
Let's fix this by adding PM runtime support to usb_hcd_platform_shutdown.
Signed-off-by: Tony Lindgren <tony@atomide.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
If the specified rcuperf.perf_type is not in the rcu_perf_init()
function's perf_ops[] array, rcuperf prints some console messages and
then invokes rcu_perf_cleanup() to set state so that a future torture
test can run. However, rcu_perf_cleanup() also attempts to end the
test that didn't actually start, and in doing so relies on the value
of cur_ops, a value that is not particularly relevant in this case.
This can result in confusing output or even follow-on failures due to
attempts to use facilities that have not been properly initialized.
This commit therefore sets the value of cur_ops to NULL in this case and
inserts a check near the beginning of rcu_perf_cleanup(), thus avoiding
relying on an irrelevant cur_ops value.
Signed-off-by: Paul E. McKenney <paulmck@linux.ibm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
If the specified rcutorture.torture_type is not in the rcu_torture_init()
function's torture_ops[] array, rcutorture prints some console messages
and then invokes rcu_torture_cleanup() to set state so that a future
torture test can run. However, rcu_torture_cleanup() also attempts to
end the test that didn't actually start, and in doing so relies on the
value of cur_ops, a value that is not particularly relevant in this case.
This can result in confusing output or even follow-on failures due to
attempts to use facilities that have not been properly initialized.
This commit therefore sets the value of cur_ops to NULL in this case
and inserts a check near the beginning of rcu_torture_cleanup(),
thus avoiding relying on an irrelevant cur_ops value.
Reported-by: kernel test robot <rong.a.chen@intel.com> Signed-off-by: Paul E. McKenney <paulmck@linux.ibm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
There has been a lurking "TBD" in the machine check poll routine ever
since it was first split out from the machine check handler. The
potential issue is that the poll routine may have just begun a read from
the STATUS register in a machine check bank when the hardware logs an
error in that bank and signals a machine check.
That race used to be pretty small back when machine checks were
broadcast, but the addition of local machine check means that the poll
code could continue running and clear the error from the bank before the
local machine check handler on another CPU gets around to reading it.
Fix the code to be sure to only process errors that need to be processed
in the poll code, leaving other logged errors alone for the machine
check handler to find and process.
[ bp: Massage a bit and flip the "== 0" check to the usual !(..) test. ]
Fixes: b79109c3bbcf ("x86, mce: separate correct machine check poller and fatal exception handler") Fixes: ed7290d0ee8f ("x86, mce: implement new status bits") Reported-by: Ashok Raj <ashok.raj@intel.com> Signed-off-by: Tony Luck <tony.luck@intel.com> Signed-off-by: Borislav Petkov <bp@suse.de> Cc: Ashok Raj <ashok.raj@intel.com> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: linux-edac <linux-edac@vger.kernel.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: x86-ml <x86@kernel.org> Cc: Yazen Ghannam <Yazen.Ghannam@amd.com> Link: https://lkml.kernel.org/r/20190312170938.GA23035@agluck-desk Signed-off-by: Sasha Levin <sashal@kernel.org>
ipw->attr_memory and ipw->common_memory are assigned with the
return value of ioremap. ioremap may fail, but no checks
are enforced. The fix inserts the checks to avoid potential
NULL pointer dereferences.
Signed-off-by: Kangjie Lu <kjlu@umn.edu> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
For regular serial ports we do not initialize value of vtermno
variable. A garbage value is assigned for non console ports.
The value can be observed as a random integer with [1].
[1] vim /sys/kernel/debug/virtio-ports/vport*p*
This patch initialize the value of vtermno for console serial
ports to '1' and regular serial ports are initiaized to '0'.
Smatch marks skb->data as untrusted so it warns that "evt_hdr->dlen"
can copy up to 255 bytes and we only have room for two bytes. Even
if this comes from the firmware and we trust it, the new policy
generally is just to fix it as kernel hardenning.
I can't test this code so I tried to be very conservative. I considered
not allowing "evt_hdr->dlen == 1" because it doesn't initialize the
whole variable but in the end I decided to allow it and manually
initialized "asic_id" and "asic_ver" to zero.
Fixes: e8454ff7b9a4 ("[media] drivers:media:radio: wl128x: FM Driver Common sources") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The use of zero-sized array causes undefined behaviour when it is not
the last member in a structure. As it happens to be in this case.
Also, the current code makes use of a language extension to the C90
standard, but the preferred mechanism to declare variable-length
types such as this one is a flexible array member, introduced in
C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last. Which is beneficial
to cultivate a high-quality code.
Fixes: e48f129c2f20 ("[SCSI] cxgb3i: convert cdev->l2opt to use rcu to prevent NULL dereference") Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The call to of_parse_phandle returns a node pointer with refcount
incremented thus it must be explicitly decremented after the last
usage.
Detected by coccinelle with the following warnings:
./sound/soc/fsl/fsl_utils.c:74:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 38, but without a corresponding object release within this function.
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn> Cc: Timur Tabi <timur@kernel.org> Cc: Nicolin Chen <nicoleotsuka@gmail.com> Cc: Xiubo Li <Xiubo.Lee@gmail.com> Cc: Fabio Estevam <festevam@gmail.com> Cc: Liam Girdwood <lgirdwood@gmail.com> Cc: Mark Brown <broonie@kernel.org> Cc: Jaroslav Kysela <perex@perex.cz> Cc: Takashi Iwai <tiwai@suse.com> Cc: alsa-devel@alsa-project.org Cc: linuxppc-dev@lists.ozlabs.org Cc: linux-kernel@vger.kernel.org Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The call to of_parse_phandle returns a node pointer with refcount
incremented thus it must be explicitly decremented after the last
usage.
Detected by coccinelle with the following warnings:
./sound/soc/fsl/eukrea-tlv320.c:121:3-9: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 102, but without a correspo nding object release within this function.
./sound/soc/fsl/eukrea-tlv320.c:127:3-9: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 102, but without a correspo nding object release within this function.
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn> Cc: Liam Girdwood <lgirdwood@gmail.com> Cc: Mark Brown <broonie@kernel.org> Cc: Jaroslav Kysela <perex@perex.cz> Cc: Takashi Iwai <tiwai@suse.com> Cc: alsa-devel@alsa-project.org Cc: linux-kernel@vger.kernel.org Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
As seen on some USB wireless keyboards manufactured by Primax, the HID
parser was using some assumptions that are not always true. In this case
it's s the fact that, inside the scope of a main item, an Usage Page
will always precede an Usage.
The spec is not pretty clear as 6.2.2.7 states "Any usage that follows
is interpreted as a Usage ID and concatenated with the Usage Page".
While 6.2.2.8 states "When the parser encounters a main item it
concatenates the last declared Usage Page with a Usage to form a
complete usage value." Being somewhat contradictory it was decided to
match Window's implementation, which follows 6.2.2.8.
In summary, the patch moves the Usage Page concatenation from the local
item parsing function to the main item parsing function.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de> Reviewed-by: Terry Junge <terry.junge@poly.com> Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Occasionally GCC is less agressive with inlining and the following is
observed:
arch/x86/kernel/signal.o: warning: objtool: restore_sigcontext()+0x3cc: call to force_valid_ss.isra.5() with UACCESS enabled
arch/x86/kernel/signal.o: warning: objtool: do_signal()+0x384: call to frame_uc_flags.isra.0() with UACCESS enabled
Cure this by moving this code out of the AC=1 region, since it really
isn't needed for the user access.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Reviewed-by: Andy Lutomirski <luto@kernel.org> Cc: Borislav Petkov <bp@alien8.de> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The call to of_get_next_child returns a node pointer with refcount
incremented thus it must be explicitly decremented after the last
usage.
Detected by coccinelle with the following warnings:
./arch/arm64/kernel/cpu_ops.c:102:1-7: ERROR: missing of_node_put;
acquired a node pointer with refcount incremented on line 69, but
without a corresponding object release within this function.
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Will Deacon <will.deacon@arm.com> Cc: linux-arm-kernel@lists.infradead.org Cc: linux-kernel@vger.kernel.org Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
For regulators used by UFS, vcc, vccq and vccq2 will have voltage range
initialized by ufshcd_populate_vreg(), however other regulators may have
undefined voltage range if dt-bindings have no such definition.
In above undefined case, both "min_uV" and "max_uV" fields in ufs_vreg
struct will be zero values and these values will be configured on
regulators in different power modes.
Currently this may have no harm if both "min_uV" and "max_uV" always keep
"zero values" because regulator_set_voltage() will always bypass such
invalid values and return "good" results.
However improper values shall be fixed to avoid potential bugs. Simply
bypass voltage configuration if voltage range is not defined.
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com> Reviewed-by: Avri Altman <avri.altman@wdc.com> Acked-by: Alim Akhtar <alim.akhtar@samsung.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently if a regulator has "<name>-fixed-regulator" property in device
tree, it will skip current limit initialization. This lead to a zero
"max_uA" value in struct ufs_vreg.
However, "regulator_set_load" operation shall be required on regulators
which have valid current limits, otherwise a zero "max_uA" set by
"regulator_set_load" may cause unexpected behavior when this regulator is
enabled or set as high power mode.
Similarly, in device's icc_level configuration flow, the target icc_level
shall be updated if regulator also has valid current limit, otherwise a
wrong icc_level will be calculated by zero "max_uA" and thus causes
unexpected results after it is written to device.
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com> Reviewed-by: Avri Altman <avri.altman@wdc.com> Acked-by: Alim Akhtar <alim.akhtar@samsung.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fix a race which leads to an Oops with NULL pointer dereference. The
dereference is in brcmf_config_dongle() when cfg_to_ndev() attempts to get
net_device structure of interface with index 0 via if2bss mapping. This
shouldn't fail because of check for bus being ready in brcmf_netdev_open(),
but it's not synchronised with USB disconnect and there is a race: after
the check the bus can be marked down and the mapping for interface 0 may be
gone.
Solve this by modifying disconnect handling so that the removal of mapping
of ifidx to brcmf_if structure happens after netdev removal (which is
synchronous with brcmf_netdev_open() thanks to rtln being locked in
devinet_ioctl()). This assures brcmf_netdev_open() returns before the
mapping is removed during disconnect.
Signed-off-by: Piotr Figiel <p.figiel@camlintechnologies.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
It was observed that rarely during USB disconnect happening shortly after
connect (before full initialization completes) usb_hub_wq would wait
forever for the dev_init_lock to be unlocked. dev_init_lock would remain
locked though because of infinite wait during usb_kill_urb:
[ 2730.656472] kworker/0:2 D 0 260 2 0x00000000
[ 2730.660700] Workqueue: events request_firmware_work_func
[ 2730.664807] [<809dca20>] (__schedule) from [<809dd164>] (schedule+0x4c/0xac)
[ 2730.670587] [<809dd164>] (schedule) from [<8069af44>] (usb_kill_urb+0xdc/0x114)
[ 2730.676815] [<8069af44>] (usb_kill_urb) from [<7f258b50>] (brcmf_usb_free_q+0x34/0xa8 [brcmfmac])
[ 2730.684833] [<7f258b50>] (brcmf_usb_free_q [brcmfmac]) from [<7f2517d4>] (brcmf_detach+0xa0/0xb8 [brcmfmac])
[ 2730.693557] [<7f2517d4>] (brcmf_detach [brcmfmac]) from [<7f251a34>] (brcmf_attach+0xac/0x3d8 [brcmfmac])
[ 2730.702094] [<7f251a34>] (brcmf_attach [brcmfmac]) from [<7f2587ac>] (brcmf_usb_probe_phase2+0x468/0x4a0 [brcmfmac])
[ 2730.711601] [<7f2587ac>] (brcmf_usb_probe_phase2 [brcmfmac]) from [<7f252888>] (brcmf_fw_request_done+0x194/0x220 [brcmfmac])
[ 2730.721795] [<7f252888>] (brcmf_fw_request_done [brcmfmac]) from [<805748e4>] (request_firmware_work_func+0x4c/0x88)
[ 2730.731125] [<805748e4>] (request_firmware_work_func) from [<80141474>] (process_one_work+0x228/0x808)
[ 2730.739223] [<80141474>] (process_one_work) from [<80141a80>] (worker_thread+0x2c/0x564)
[ 2730.746105] [<80141a80>] (worker_thread) from [<80147bcc>] (kthread+0x13c/0x16c)
[ 2730.752227] [<80147bcc>] (kthread) from [<801010b4>] (ret_from_fork+0x14/0x20)
[ 2733.099695] kworker/0:3 D 0 1065 2 0x00000000
[ 2733.103926] Workqueue: usb_hub_wq hub_event
[ 2733.106914] [<809dca20>] (__schedule) from [<809dd164>] (schedule+0x4c/0xac)
[ 2733.112693] [<809dd164>] (schedule) from [<809e2a8c>] (schedule_timeout+0x214/0x3e4)
[ 2733.119621] [<809e2a8c>] (schedule_timeout) from [<809dde2c>] (wait_for_common+0xc4/0x1c0)
[ 2733.126810] [<809dde2c>] (wait_for_common) from [<7f258d00>] (brcmf_usb_disconnect+0x1c/0x4c [brcmfmac])
[ 2733.135206] [<7f258d00>] (brcmf_usb_disconnect [brcmfmac]) from [<8069e0c8>] (usb_unbind_interface+0x5c/0x1e4)
[ 2733.143943] [<8069e0c8>] (usb_unbind_interface) from [<8056d3e8>] (device_release_driver_internal+0x164/0x1fc)
[ 2733.152769] [<8056d3e8>] (device_release_driver_internal) from [<8056c078>] (bus_remove_device+0xd0/0xfc)
[ 2733.161138] [<8056c078>] (bus_remove_device) from [<8056977c>] (device_del+0x11c/0x310)
[ 2733.167939] [<8056977c>] (device_del) from [<8069cba8>] (usb_disable_device+0xa0/0x1cc)
[ 2733.174743] [<8069cba8>] (usb_disable_device) from [<8069507c>] (usb_disconnect+0x74/0x1dc)
[ 2733.181823] [<8069507c>] (usb_disconnect) from [<80695e88>] (hub_event+0x478/0xf88)
[ 2733.188278] [<80695e88>] (hub_event) from [<80141474>] (process_one_work+0x228/0x808)
[ 2733.194905] [<80141474>] (process_one_work) from [<80141a80>] (worker_thread+0x2c/0x564)
[ 2733.201724] [<80141a80>] (worker_thread) from [<80147bcc>] (kthread+0x13c/0x16c)
[ 2733.207913] [<80147bcc>] (kthread) from [<801010b4>] (ret_from_fork+0x14/0x20)
It was traced down to a case where usb_kill_urb would be called on an URB
structure containing more or less random data, including large number in
its use_count. During the debugging it appeared that in brcmf_usb_free_q()
the traversal over URBs' lists is not synchronized with operations on those
lists in brcmf_usb_rx_complete() leading to handling
brcmf_usbdev_info structure (holding lists' head) as lists' element and in
result causing above problem.
Fix it by walking through all URBs during brcmf_cancel_all_urbs using the
arrays of requests instead of linked lists.
Signed-off-by: Piotr Figiel <p.figiel@camlintechnologies.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Leaving dev_init_lock mutex locked in probe causes BUG and a WARNING when
kernel is compiled with CONFIG_PROVE_LOCKING. Convert mutex to completion
which silences those warnings and improves code readability.
Fix below errors when connecting the USB WiFi dongle:
brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac43143 for chip BCM43143/2
BUG: workqueue leaked lock or atomic: kworker/0:2/0x00000000/434
last function: hub_event
1 lock held by kworker/0:2/434:
#0: 18d5dcdf (&devinfo->dev_init_lock){+.+.}, at: brcmf_usb_probe+0x78/0x550 [brcmfmac]
CPU: 0 PID: 434 Comm: kworker/0:2 Not tainted 4.19.23-00084-g454a789-dirty #123
Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree)
Workqueue: usb_hub_wq hub_event
[<8011237c>] (unwind_backtrace) from [<8010d74c>] (show_stack+0x10/0x14)
[<8010d74c>] (show_stack) from [<809c4324>] (dump_stack+0xa8/0xd4)
[<809c4324>] (dump_stack) from [<8014195c>] (process_one_work+0x710/0x808)
[<8014195c>] (process_one_work) from [<80141a80>] (worker_thread+0x2c/0x564)
[<80141a80>] (worker_thread) from [<80147bcc>] (kthread+0x13c/0x16c)
[<80147bcc>] (kthread) from [<801010b4>] (ret_from_fork+0x14/0x20)
Exception stack(0xed1d9fb0 to 0xed1d9ff8)
9fa0: 00000000000000000000000000000000
9fc0: 0000000000000000000000000000000000000000000000000000000000000000
9fe0: 000000000000000000000000000000000000001300000000
======================================================
WARNING: possible circular locking dependency detected 4.19.23-00084-g454a789-dirty #123 Not tainted
------------------------------------------------------
kworker/0:2/434 is trying to acquire lock: e29cf799 ((wq_completion)"events"){+.+.}, at: process_one_work+0x174/0x808
but task is already holding lock: 18d5dcdf (&devinfo->dev_init_lock){+.+.}, at: brcmf_usb_probe+0x78/0x550 [brcmfmac]
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
Signed-off-by: Piotr Figiel <p.figiel@camlintechnologies.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Clang warns about what is clearly a case of passing an uninitalized
variable into a static function:
drivers/net/wireless/broadcom/b43/phy_lp.c:1852:23: error: variable 'gains' is uninitialized when used here
[-Werror,-Wuninitialized]
lpphy_papd_cal(dev, gains, 0, 1, 30);
^~~~~
drivers/net/wireless/broadcom/b43/phy_lp.c:1838:2: note: variable 'gains' is declared here
struct lpphy_tx_gains gains, oldgains;
^
1 error generated.
However, this function is empty, and its arguments are never evaluated,
so gcc in contrast does not warn here. Both compilers behave in a
reasonable way as far as I can tell, so we should change the code
to avoid the warning everywhere.
We could just eliminate the lpphy_papd_cal() function entirely,
given that it has had the TODO comment in it for 10 years now
and is rather unlikely to ever get done. I'm doing a simpler
change here, and just pass the 'oldgains' variable in that has
been initialized, based on the guess that this is what was
originally meant.
Fixes: 2c0d6100da3e ("b43: LP-PHY: Begin implementing calibration & software RFKILL support") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Larry Finger <Larry.Finger@lwfinger.net> Reviewed-by: Nathan Chancellor <natechancellor@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In case kmemdup fails, the fix sets conn_info->req_ie_len and
conn_info->resp_ie_len to zero to avoid buffer overflows.
Signed-off-by: Kangjie Lu <kjlu@umn.edu> Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When building with -Wsometimes-uninitialized, Clang warns:
drivers/iio/common/ssp_sensors/ssp_iio.c:95:6: warning: variable
'calculated_time' is used uninitialized whenever 'if' condition is false
[-Wsometimes-uninitialized]
While it isn't wrong, this will never be a problem because
iio_push_to_buffers_with_timestamp only uses calculated_time
on the same condition that it is assigned (when scan_timestamp
is not zero). While iio_push_to_buffers_with_timestamp is marked
as inline, Clang does inlining in the optimization stage, which
happens after the semantic analysis phase (plus inline is merely
a hint to the compiler).
Fix this by just zero initializing calculated_time.
Link: https://github.com/ClangBuiltLinux/linux/issues/394 Signed-off-by: Nathan Chancellor <natechancellor@gmail.com> Reviewed-by: Nick Desaulniers <ndesaulniers@google.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
For devices from the SigmaDelta family we need to keep CS low when doing a
conversion, since the device will use the MISO line as a interrupt to
indicate that the conversion is complete.
This is why the driver locks the SPI bus and when the SPI bus is locked
keeps as long as a conversion is going on. The current implementation gets
one small detail wrong though. CS is only de-asserted after the SPI bus is
unlocked. This means it is possible for a different SPI device on the same
bus to send a message which would be wrongfully be addressed to the
SigmaDelta device as well. Make sure that the last SPI transfer that is
done while holding the SPI bus lock de-asserts the CS signal.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Signed-off-by: Alexandru Ardelean <Alexandru.Ardelean@analog.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The LLVM linker (ld.lld) defaults to removing local relocations, which
causes KASLR boot failures. ld.bfd and ld.gold already handle this
correctly. This adds the explicit instruction "--discard-none" during
the link phase. There is no change in output for ld.bfd and ld.gold,
but ld.lld now produces an image with all the needed relocations.
The call to of_find_node_by_name returns a node pointer with refcount
incremented thus it must be explicitly decremented after the last
usage.
Detected by coccinelle with the following warnings:
./drivers/cpufreq/pmac32-cpufreq.c:557:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 552, but without a corresponding object release within this function.
./drivers/cpufreq/pmac32-cpufreq.c:569:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 552, but without a corresponding object release within this function.
./drivers/cpufreq/pmac32-cpufreq.c:598:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 587, but without a corresponding object release within this function.
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn> Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net> Cc: Viresh Kumar <viresh.kumar@linaro.org> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Paul Mackerras <paulus@samba.org> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: linux-pm@vger.kernel.org Cc: linuxppc-dev@lists.ozlabs.org Cc: linux-kernel@vger.kernel.org Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The call to of_get_cpu_node returns a node pointer with refcount
incremented thus it must be explicitly decremented after the last
usage.
Detected by coccinelle with the following warnings:
./drivers/cpufreq/pasemi-cpufreq.c:212:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 147, but without a corresponding object release within this function.
./drivers/cpufreq/pasemi-cpufreq.c:220:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 147, but without a corresponding object release within this function.
The call to of_get_cpu_node returns a node pointer with refcount
incremented thus it must be explicitly decremented after the last
usage.
Detected by coccinelle with the following warnings:
./drivers/cpufreq/ppc_cbe_cpufreq.c:89:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 76, but without a corresponding object release within this function.
./drivers/cpufreq/ppc_cbe_cpufreq.c:89:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 76, but without a corresponding object release within this function.
Microphone detection provides the button detection features on the
Arizona CODECs as such it will be running if the jack is currently
inserted. If the driver is unbound whilst the jack is still inserted
this will cause warnings from the regulator framework as the MICVDD
regulator is put but was never disabled.
Correct this by disabling microphone detection on driver removal and if
the microphone detection was running disable the regulator and put the
runtime reference that was currently held.
The dev->power.direct_complete flag may become set in device_prepare() in
case the device don't have any PM callbacks (dev->power.no_pm_callbacks is
set). This leads to a broken behaviour, when there is child having wakeup
enabled and relies on its parent to be used in the wakeup path.
More precisely, when the direct complete path becomes selected for the
child in __device_suspend(), the propagation of the dev->power.wakeup_path
becomes skipped as well.
Let's address this problem, by checking if the device is a part the wakeup
path or has wakeup enabled, then prevent the direct complete path from
being used.
eSDHC-A001: The data timeout counter (SYSCTL[DTOCV]) is not
reliable for DTOCV values 0x4(2^17 SD clock), 0x8(2^21 SD clock),
and 0xC(2^25 SD clock). The data timeout counter can count from
2^13–2^27, but for values 2^17, 2^21, and 2^25, the timeout
counter counts for only 2^13 SD clocks.
A-008358: The data timeout counter value loaded into the timeout
counter is less than expected and can result into early timeout
error in case of eSDHC data transactions. The table below shows
the expected vs actual timeout period for different values of
SYSCTL[DTOCV]:
these two erratum has the same quirk to control it, and set
SDHCI_QUIRK_RESET_AFTER_REQUEST to fix above issue.
Software writing to the Transfer Type configuration register
(system clock domain) can cause a setup/hold violation in the
CRC flops (card clock domain), which can cause write accesses
to be sent with corrupt CRC values. This issue occurs only for
write preceded by read. this erratum is to fix this issue.
pwrseq_emmc.c implements a HW reset procedure for eMMC chip by driving a
GPIO line.
It registers the .reset() cb on mmc_pwrseq_ops and it registers a system
restart notification handler; both of them perform reset by unconditionally
calling gpiod_set_value().
If the eMMC reset line is tied to a GPIO controller whose driver can sleep
(i.e. I2C GPIO controller), then the kernel would spit warnings when trying
to reset the eMMC chip by means of .reset() mmc_pwrseq_ops cb (that is
exactly what I'm seeing during boot).
Furthermore, on system reset we would gets to the system restart
notification handler with disabled interrupts - local_irq_disable() is
called in machine_restart() at least on ARM/ARM64 - and we would be in
trouble when the GPIO driver tries to sleep (which indeed doesn't happen
here, likely because in my case the machine specific code doesn't call
do_kernel_restart(), I guess..).
This patch fixes the .reset() cb to make use of gpiod_set_value_cansleep(),
so that the eMMC gets reset on boot without complaints, while, since there
isn't that much we can do, we avoid register the restart handler if the
GPIO controller has a sleepy driver (and we spit a dev_notice() message to
let people know)..
This had been tested on a downstream 4.9 kernel with backported
commit 83f37ee7ba33 ("mmc: pwrseq: Add reset callback to the struct
mmc_pwrseq_ops") and commit ae60fb031cf2 ("mmc: core: Don't do eMMC HW
reset when resuming the eMMC card"), because I couldn't boot my board
otherwise. Maybe worth to RFT.
When we discover the PHY is empty in sas_rediscover_dev(), the PHY
information (like negotiated linkrate) is not updated.
As such, for a user examining sysfs for that PHY, they would see
incorrect values:
root@(none)$ cd /sys/class/sas_phy/phy-0:0:20
root@(none)$ more negotiated_linkrate
3.0 Gbit
root@(none)$ echo 0 > enable
root@(none)$ more negotiated_linkrate
3.0 Gbit
So fix this, simply discover the PHY again, even though we know it's empty;
in the above example, this gives us:
root@(none)$ more negotiated_linkrate
Phy disabled
We must do this after unregistering the device associated with the PHY
(in sas_unregister_devs_sas_addr()).
Signed-off-by: John Garry <john.garry@huawei.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Also, other drivers may attempt to access the LPC bus at the same time,
resulting in undefined behavior.
Use request_muxed_region() to ensure that IO access on the requested
address space is supported, and to ensure that access by multiple
drivers is synchronized.
Fixes: e53004e20a58e ("hwmon: New f71805f driver") Reported-by: Kefeng Wang <wangkefeng.wang@huawei.com> Reported-by: John Garry <john.garry@huawei.com> Cc: John Garry <john.garry@huawei.com> Acked-by: John Garry <john.garry@huawei.com> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Super-IO accesses may fail on a system with no or unmapped LPC bus.
Also, other drivers may attempt to access the LPC bus at the same time,
resulting in undefined behavior.
Use request_muxed_region() to ensure that IO access on the requested
address space is supported, and to ensure that access by multiple drivers
is synchronized.
Fixes: ba224e2c4f0a7 ("hwmon: New PC87427 hardware monitoring driver") Reported-by: Kefeng Wang <wangkefeng.wang@huawei.com> Reported-by: John Garry <john.garry@huawei.com> Cc: John Garry <john.garry@huawei.com> Acked-by: John Garry <john.garry@huawei.com> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Super-IO accesses may fail on a system with no or unmapped LPC bus.
Also, other drivers may attempt to access the LPC bus at the same time,
resulting in undefined behavior.
Use request_muxed_region() to ensure that IO access on the requested
address space is supported, and to ensure that access by multiple drivers
is synchronized.
Fixes: 8d5d45fb1468 ("I2C: Move hwmon drivers (2/3)") Reported-by: Kefeng Wang <wangkefeng.wang@huawei.com> Reported-by: John Garry <john.garry@huawei.com> Cc: John Garry <john.garry@huawei.com> Acked-by: John Garry <john.garry@huawei.com> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Super-IO accesses may fail on a system with no or unmapped LPC bus.
Also, other drivers may attempt to access the LPC bus at the same time,
resulting in undefined behavior.
Use request_muxed_region() to ensure that IO access on the requested
address space is supported, and to ensure that access by multiple drivers
is synchronized.
Fixes: 8d5d45fb1468 ("I2C: Move hwmon drivers (2/3)") Reported-by: Kefeng Wang <wangkefeng.wang@huawei.com> Reported-by: John Garry <john.garry@huawei.com> Cc: John Garry <john.garry@huawei.com> Acked-by: John Garry <john.garry@huawei.com> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Super-IO accesses may fail on a system with no or unmapped LPC bus.
Also, other drivers may attempt to access the LPC bus at the same time,
resulting in undefined behavior.
Use request_muxed_region() to ensure that IO access on the requested
address space is supported, and to ensure that access by multiple drivers
is synchronized.
Fixes: 2219cd81a6cd ("hwmon/vt1211: Add probing of alternate config index port") Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently if alloc_skb fails to allocate the skb a null skb is passed to
t4_set_arp_err_handler and this ends up dereferencing the null skb. Avoid
the NULL pointer dereference by checking for a NULL skb and returning
early.
Addresses-Coverity: ("Dereference null return") Fixes: b38a0ad8ec11 ("RDMA/cxgb4: Set arp error handler for PASS_ACCEPT_RPL messages") Signed-off-by: Colin Ian King <colin.king@canonical.com> Acked-by: Potnuri Bharat Teja <bharat@chelsio.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / thirdparty / kernel / stable.git / log
