When Broadcom SDIO cards are idled they go to sleep and a whole
separate subsystem takes over their SDIO communication. This is the
Always-On-Subsystem (AOS) and it can't handle tuning requests.
Specifically, as tested on rk3288-veyron-minnie (which reports having
BCM4354/1 in dmesg), if I force a retune in brcmf_sdio_kso_control()
when "on = 1" (aka we're transition from sleep to wake) by whacking:
bus->sdiodev->func1->card->host->need_retune = 1
...then I can often see tuning fail. In this case dw_mmc reports "All
phases bad!"). Note that I don't get 100% failure, presumably because
sometimes the card itself has already transitioned away from the AOS
itself by the time we try to wake it up. If I force retuning when "on
= 0" (AKA force retuning right before sending the command to go to
sleep) then retuning is always OK.
NOTE: we need _both_ this patch and the patch to avoid triggering
tuning due to CRC errors in the sleep/wake transition, AKA ("brcmfmac:
sdio: Disable auto-tuning around commands expected to fail"). Though
both patches handle issues with Broadcom's AOS, the problems are
distinct:
1. We want to defer (but not ignore) asynchronous (like
timer-requested) tuning requests till the card is awake. However,
we want to ignore CRC errors during the transition, we don't want
to queue deferred tuning request.
2. You could imagine that the AOS could implement retuning but we
could still get errors while transitioning in and out of the AOS.
Similarly you could imagine a seamless transition into and out of
the AOS (with no CRC errors) even if the AOS couldn't handle
tuning.
ALSO NOTE: presumably there is never a desperate need to retune in
order to wake up the card, since doing so is impossible. Luckily the
only way the card can get into sleep state is if we had a good enough
tuning to send it the command to put it into sleep, so presumably that
"good enough" tuning is enough to wake us up, at least with a few
retries.
Cc: stable@vger.kernel.org #v4.18+ Signed-off-by: Douglas Anderson <dianders@chromium.org> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com> Acked-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are certain cases, notably when transitioning between sleep and
active state, when Broadcom SDIO WiFi cards will produce errors on the
SDIO bus. This is evident from the source code where you can see that
we try commands in a loop until we either get success or we've tried
too many times. The comment in the code reinforces this by saying
"just one write attempt may fail"
Unfortunately these failures sometimes end up causing an "-EILSEQ"
back to the core which triggers a retuning of the SDIO card and that
blocks all traffic to the card until it's done.
Let's disable retuning around the commands we expect might fail.
Cc: stable@vger.kernel.org #v4.18+ Signed-off-by: Douglas Anderson <dianders@chromium.org> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com> Acked-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A packed AppArmor policy contains null-terminated tag strings that are read
by unpack_nameX(). However, unpack_nameX() uses string functions on them
without ensuring that they are actually null-terminated, potentially
leading to out-of-bounds accesses.
Make sure that the tag string is null-terminated before passing it to
strcmp().
Cc: stable@vger.kernel.org Fixes: 736ec752d95e ("AppArmor: policy routines for loading and unpacking policy") Signed-off-by: Jann Horn <jannh@google.com> Signed-off-by: John Johansen <john.johansen@canonical.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While commit 11c236b89d7c2 ("apparmor: add a default null dfa") ensure
every profile has a policy.dfa it does not resize the policy.start[]
to have entries for every possible start value. Which means
PROFILE_MEDIATES is not safe to use on untrusted input. Unforunately
commit b9590ad4c4f2 ("apparmor: remove POLICY_MEDIATES_SAFE") did not
take into account the start value usage.
The input string in profile_query_cb() is user controlled and is not
properly checked to be within the limited start[] entries, even worse
it can't be as userspace policy is allowed to make us of entries types
the kernel does not know about. This mean usespace can currently cause
the kernel to access memory up to 240 entries beyond the start array
bounds.
On Chuwi Hi10 Plus, the Silead device id is MSSL0017.
Signed-off-by: Daniel Smith <danct12@disroot.org> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Cc: stable@vger.kernel.org Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the case of compat syscall ioctl numbers for UI_BEGIN_FF_UPLOAD and
UI_END_FF_UPLOAD need to be adjusted before being passed on
uinput_ioctl_handler() since code built with -m32 will be passing
slightly different values. Extend the code already covering
UI_SET_PHYS to cover UI_BEGIN_FF_UPLOAD and UI_END_FF_UPLOAD as well.
Register EE_VERSION contains mixture of calibration information and DSP
version. So far, because calibrations were definite, the driver
compatibility depended on whole contents, but in the newer production
process the calibration part changes. Because of that, value in EE_VERSION
will be changed and to avoid that calibration value is same as DSP version
the MSB in calibration part was fixed to 1.
That means existing calibrations (medical and consumer) will now have
hex values (bits 8 to 15) of 83 and 84 respectively. Driver compatibility
should be based only on DSP version part of the EE_VERSION (bits 0 to 7)
register.
Signed-off-by: Crt Mori <cmo@melexis.com> Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A USB3 device needs to be reset and re-enumarated if the port it
connects to goes to a error state, with link state inactive.
There is no use in trying to recover failed transactions by resetting
endpoints at this stage. Tests show that in rare cases, after multiple
endpoint resets of a roothub port the whole host controller might stop
completely.
Several retries to recover from transaction error can happen as
it can take a long time before the hub thread discovers the USB3
port error and inactive link.
We can't reliably detect the port error from slot or endpoint context
due to a limitation in xhci, see xhci specs section 4.8.3:
"There are several cases where the EP State field in the Output
Endpoint Context may not reflect the current state of an endpoint"
and
"Software should maintain an accurate value for EP State, by tracking it
with an internal variable that is driven by Events and Doorbell accesses"
Same appears to be true for slot state.
set a flag to the corresponding slot if a USB3 roothub port link goes
inactive to prevent both queueing new URBs and resetting endpoints.
USB 3.2 capability in a host can be detected from the
xHCI Supported Protocol Capability major and minor revision fields.
If major is 0x3 and minor 0x20 then the host is USB 3.2 capable.
For USB 3.2 capable hosts set the root hub lane count to 2.
The Major Revision and Minor Revision fields contain a BCD version number.
The value of the Major Revision field is JJh and the value of the Minor
Revision field is MNh for version JJ.M.N, where JJ = major revision number,
M - minor version number, N = sub-minor version number,
e.g. version 3.1 is represented with a value of 0310h.
Also fix the extra whitespace printed out when announcing regular
SuperSpeed hosts.
An endpoint conflict occurs when the USB is working in device mode
during an isochronous communication. When the endpointA IN direction
is an isochronous IN endpoint, and the host sends an IN token to
endpointA on another device, then the OUT transaction may be missed
regardless the OUT endpoint number. Generally, this occurs when the
device is connected to the host through a hub and other devices are
connected to the same hub.
The affected OUT endpoint can be either control, bulk, isochronous, or
an interrupt endpoint. After the OUT endpoint is primed, if an IN token
to the same endpoint number on another device is received, then the OUT
endpoint may be unprimed (cannot be detected by software), which causes
this endpoint to no longer respond to the host OUT token, and thus, no
corresponding interrupt occurs.
There is no good workaround for this issue, the only thing the software
could do is numbering isochronous IN from the highest endpoint since we
have observed most of device number endpoint from the lowest.
Cc: <stable@vger.kernel.org> #v3.14+ Cc: Fabio Estevam <festevam@gmail.com> Cc: Greg KH <gregkh@linuxfoundation.org> Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Cc: Jun Li <jun.li@nxp.com> Signed-off-by: Peter Chen <peter.chen@nxp.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
UFS runtime suspend can be triggered after pm_runtime_enable() is invoked
in ufshcd_pltfrm_init(). However if the first runtime suspend is triggered
before binding ufs_hba structure to ufs device structure via
platform_set_drvdata(), then UFS runtime suspend will be no longer
triggered in the future because its dev->power.runtime_error was set in the
first triggering and does not have any chance to be cleared.
To be more clear, dev->power.runtime_error is set if hba is NULL in
ufshcd_runtime_suspend() which returns -EINVAL to rpm_callback() where
dev->power.runtime_error is set as -EINVAL. In this case, any future
rpm_suspend() for UFS device fails because rpm_check_suspend_allowed()
fails due to non-zero
dev->power.runtime_error.
To resolve this issue, make sure the first UFS runtime suspend get valid
"hba" in ufshcd_runtime_suspend(): Enable UFS runtime PM only after hba is
successfully bound to UFS device structure.
Fixes: 62694735ca95 ([SCSI] ufs: Add runtime PM support for UFS host controller driver) Cc: stable@vger.kernel.org Signed-off-by: Stanley Chu <stanley.chu@mediatek.com> Reviewed-by: Avri Altman <avri.altman@wdc.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Processing of SDIO IRQs must obviously be prevented while the card is
system suspended, otherwise we may end up trying to communicate with an
uninitialized SDIO card.
Reports throughout the years shows that this is not only a theoretical
problem, but a real issue. So, let's finally fix this problem, by keeping
track of the state for the card and bail out before processing the SDIO
IRQ, in case the card is suspended.
Cc: stable@vger.kernel.org Reported-by: Douglas Anderson <dianders@chromium.org> Tested-by: Douglas Anderson <dianders@chromium.org> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We want SDIO drivers to be able to temporarily stop retuning when the
driver knows that the SDIO card is not in a state where retuning will
work (maybe because the card is asleep). We'll move the relevant
functions to a place where drivers can call them.
Cc: stable@vger.kernel.org #v4.18+ Signed-off-by: Douglas Anderson <dianders@chromium.org> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Acked-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Normally when the MMC core sees an "-EILSEQ" error returned by a host
controller then it will trigger a retuning of the card. This is
generally a good idea.
However, if a command is expected to sometimes cause transfer errors
then these transfer errors shouldn't cause a re-tuning. This
re-tuning will be a needless waste of time. One example case where a
transfer is expected to cause errors is when transitioning between
idle (sometimes referred to as "sleep" in Broadcom code) and active
state on certain Broadcom WiFi SDIO cards. Specifically if the card
was already transitioning between states when the command was sent it
could cause an error on the SDIO bus.
Let's add an API that the SDIO function drivers can call that will
temporarily disable the auto-tuning functionality. Then we can add a
call to this in the Broadcom WiFi driver and any other driver that
might have similar needs.
NOTE: this makes the assumption that the card is already tuned well
enough that it's OK to disable the auto-retuning during one of these
error-prone situations. Presumably the driver code performing the
error-prone transfer knows how to recover / retry from errors. ...and
after we can get back to a state where transfers are no longer
error-prone then we can enable the auto-retuning again. If we truly
find ourselves in a case where the card needs to be retuned sometimes
to handle one of these error-prone transfers then we can always try a
few transfers first without auto-retuning and then re-try with
auto-retuning if the first few fail.
Without this change on rk3288-veyron-minnie I periodically see this in
the logs of a machine just sitting there idle:
dwmmc_rockchip ff0d0000.dwmmc: Successfully tuned phase to XYZ
Cc: stable@vger.kernel.org #v4.18+ Signed-off-by: Douglas Anderson <dianders@chromium.org> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Acked-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The O2Micro controller only supports tuning at 4-bits. So the host driver
needs to change the bus width while tuning and then set it back when done.
There was a bug in the original implementation in that mmc->ios.bus_width
also wasn't updated. Thus setting the incorrect blocksize in
sdhci_send_tuning which results in a tuning failure.
Signed-off-by: Raul E Rangel <rrangel@chromium.org> Fixes: 0086fc217d5d7 ("mmc: sdhci: Add support for O2 hardware tuning") Acked-by: Adrian Hunter <adrian.hunter@intel.com> Cc: stable@vger.kernel.org Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The inline assembler functions ap_aqic() and ap_qact() used two
variables declared on the very same register. One variable was for
input only, the other for output. Looks like newer versions of the gcc
don't like this. Anyway it is a better coding to use one variable
(which may have a union data type) on one register for input and
output. So this patch introduces unions and uses only one variable now
for input and output for GR1 for the PQAP(QACT) and PQAP(QIC)
invocation.
Signed-off-by: Harald Freudenberger <freude@linux.ibm.com> Acked-by: Ilya Leoshkevich <iii@linux.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
[heiko.carstens@de.ibm.com]:
-----
Laura Abbott reported that the kernel doesn't build anymore with gcc 9,
due to the "X" constraint. Ilya provided the gcc 9 patch "S/390:
Introduce jdd constraint" which introduces the new "jdd" constraint
which fixes this.
-----
The support for section anchors on S/390 introduced in gcc9 has changed
the behavior of "X" constraint, which can now produce register
references. Since existing constraints, in particular, "i", do not fit
the intended use case on S/390, the new machine-specific "jdd"
constraint was introduced. This patch makes jump labels use "jdd"
constraint when building with gcc9.
Reported-by: Laura Abbott <labbott@redhat.com> Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com> Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
gcc gets a bit confused by the logic in ovl_setup_trap() and
can't figure out whether the local 'trap' variable in the caller
was initialized or not:
fs/overlayfs/super.c: In function 'ovl_fill_super':
fs/overlayfs/super.c:1333:4: error: 'trap' may be used uninitialized in this function [-Werror=maybe-uninitialized]
iput(trap);
^~~~~~~~~~
fs/overlayfs/super.c:1312:17: note: 'trap' was declared here
Reword slightly to make it easier for the compiler to understand.
Overlapping overlay layers are not supported and can cause unexpected
behavior, but overlayfs does not currently check or warn about these
configurations.
User is not supposed to specify the same directory for upper and
lower dirs or for different lower layers and user is not supposed to
specify directories that are descendants of each other for overlay
layers, but that is exactly what this zysbot repro did:
Moving layer root directories into other layers while overlayfs
is mounted could also result in unexpected behavior.
This commit places "traps" in the overlay inode hash table.
Those traps are dummy overlay inodes that are hashed by the layers
root inodes.
On mount, the hash table trap entries are used to verify that overlay
layers are not overlapping. While at it, we also verify that overlay
layers are not overlapping with directories "in-use" by other overlay
instances as upperdir/workdir.
On lookup, the trap entries are used to verify that overlay layers
root inodes have not been moved into other layers after mount.
[ 94.434900] overlayfs: overlapping upperdir path
mount: mount overlay on mnt failed: Too many levels of symbolic links
$ mount -t overlay none mnt ...
-o lowerdir=upper/0/u,upperdir=upper/0/u,workdir=upper/0/w
[ 151.350132] overlayfs: conflicting lowerdir path
mount: none is already mounted or mnt busy
$ mount -t overlay none mnt ...
-o lowerdir=lower:lower/a,upperdir=upper/0/u,workdir=upper/0/w
[ 201.205045] overlayfs: overlapping lowerdir path
mount: mount overlay on mnt failed: Too many levels of symbolic links
$ mount -t overlay none mnt ...
-o lowerdir=lower,upperdir=upper/0/u,workdir=upper/0/w
$ mv base/upper/0/ base/lower/
$ find mnt/0
mnt/0
mnt/0/w
find: 'mnt/0/w/work': Too many levels of symbolic links
find: 'mnt/0/u': Too many levels of symbolic links
Add support for processing switch jump tables in objects with multiple
.rodata sections, such as those created by '-ffunction-sections' and
'-fdata-sections'. Currently, objtool always looks in .rodata for jump
table information, which results in many "sibling call from callable
instruction with modified stack frame" warnings with objects compiled
using those flags.
The fix is comprised of three parts:
1. Flagging all .rodata sections when importing ELF information for
easier checking later.
2. Keeping a reference to the section each relocation is from in order
to get the list_head for the other relocations in that section.
3. Finding jump tables by following relocations to .rodata sections,
rather than always referencing a single global .rodata section.
The patch has been tested without data sections enabled and no
differences in the resulting orc unwind information were seen.
Note that as objtool adds terminators to end of each .text section the
unwind information generated between a function+data sections build and
a normal build aren't directly comparable. Manual inspection suggests
that objtool is now generating the correct information, or at least
making more of an effort to do so than it did previously.
Starting with GCC 9, -Warray-bounds detects cases when memset is called
starting on a member of a struct but the size to be cleared ends up
writing over further members.
Such a call happens in the trace code to clear, at once, all members
after and including `seq` on struct trace_iterator:
In function 'memset',
inlined from 'ftrace_dump' at kernel/trace/trace.c:8914:3:
./include/linux/string.h:344:9: warning: '__builtin_memset' offset
[8505, 8560] from the object at 'iter' is out of the bounds of
referenced subobject 'seq' with type 'struct trace_seq' at offset
4368 [-Warray-bounds]
344 | return __builtin_memset(p, c, size);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~
In order to avoid GCC complaining about it, we compute the address
ourselves by adding the offsetof distance instead of referring
directly to the member.
Since there are two places doing this clear (trace.c and trace_kdb.c),
take the chance to move the workaround into a single place in
the internal header.
Link: http://lkml.kernel.org/r/20190523124535.GA12931@gmail.com Signed-off-by: Miguel Ojeda <miguel.ojeda.sandonis@gmail.com>
[ Removed unnecessary parenthesis around "iter" ] Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tcp_fragment() might be called for skbs in the write queue.
Memory limits might have been exceeded because tcp_sendmsg() only
checks limits at full skb (64KB) boundaries.
Therefore, we need to make sure tcp_fragment() wont punish applications
that might have setup very low SO_SNDBUF values.
Fixes: f070ef2ac667 ("tcp: tcp_fragment() should apply sane memory limits") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: Christoph Paasch <cpaasch@apple.com> Tested-by: Christoph Paasch <cpaasch@apple.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
file_remove_privs() might be called for non-regular files, e.g.
blkdev inode. There is no reason to do its job on things
like blkdev inodes, pipes, or cdevs. Hence, abort if
file does not refer to a regular inode.
AV: more to the point, for devices there might be any number of
inodes refering to given device. Which one to strip the permissions
from, even if that made any sense in the first place? All of them
will be observed with contents modified, after all.
Found by LockDoc (Alexander Lochmann, Horst Schirmeier and Olaf
Spinczyk)
Reviewed-by: Jan Kara <jack@suse.cz> Signed-off-by: Alexander Lochmann <alexander.lochmann@tu-dortmund.de> Signed-off-by: Horst Schirmeier <horst.schirmeier@tu-dortmund.de> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Cc: Zubin Mithra <zsm@chromium.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When fixing the race conditions between the coredump and the mmap_sem
holders outside the context of the process, we focused on
mmget_not_zero()/get_task_mm() callers in 04f5866e41fb70 ("coredump: fix
race condition between mmget_not_zero()/get_task_mm() and core
dumping"), but those aren't the only cases where the mmap_sem can be
taken outside of the context of the process as Michal Hocko noticed
while backporting that commit to older -stable kernels.
If mmgrab() is called in the context of the process, but then the
mm_count reference is transferred outside the context of the process,
that can also be a problem if the mmap_sem has to be taken for writing
through that mm_count reference.
khugepaged registration calls mmgrab() in the context of the process,
but the mmap_sem for writing is taken later in the context of the
khugepaged kernel thread.
collapse_huge_page() after taking the mmap_sem for writing doesn't
modify any vma, so it's not obvious that it could cause a problem to the
coredump, but it happens to modify the pmd in a way that breaks an
invariant that pmd_trans_huge_lock() relies upon. collapse_huge_page()
needs the mmap_sem for writing just to block concurrent page faults that
call pmd_trans_huge_lock().
Specifically the invariant that "!pmd_trans_huge()" cannot become a
"pmd_trans_huge()" doesn't hold while collapse_huge_page() runs.
The coredump will call __get_user_pages() without mmap_sem for reading,
which eventually can invoke a lockless page fault which will need a
functional pmd_trans_huge_lock().
So collapse_huge_page() needs to use mmget_still_valid() to check it's
not running concurrently with the coredump... as long as the coredump
can invoke page faults without holding the mmap_sem for reading.
This has "Fixes: khugepaged" to facilitate backporting, but in my view
it's more a bug in the coredump code that will eventually have to be
rewritten to stop invoking page faults without the mmap_sem for reading.
So the long term plan is still to drop all mmget_still_valid().
Link: http://lkml.kernel.org/r/20190607161558.32104-1-aarcange@redhat.com Fixes: ba76149f47d8 ("thp: khugepaged") Signed-off-by: Andrea Arcangeli <aarcange@redhat.com> Reported-by: Michal Hocko <mhocko@suse.com> Acked-by: Michal Hocko <mhocko@suse.com> Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: Oleg Nesterov <oleg@redhat.com> Cc: Jann Horn <jannh@google.com> Cc: Hugh Dickins <hughd@google.com> Cc: Mike Rapoport <rppt@linux.vnet.ibm.com> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Peter Xu <peterx@redhat.com> Cc: Jason Gunthorpe <jgg@mellanox.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a call to kobject_init_and_add() fails we should call kobject_put()
otherwise we leak memory.
Add call to kobject_put() in the error path of call to
kobject_init_and_add(). Please note, this has the side effect that the
release method is called if kobject_init_and_add() fails.
Link: http://lkml.kernel.org/r/20190513033458.2824-1-tobin@kernel.org Signed-off-by: Tobin C. Harding <tobin@kernel.org> Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Reviewed-by: Joseph Qi <joseph.qi@linux.alibaba.com> Cc: Mark Fasheh <mark@fasheh.com> Cc: Joel Becker <jlbec@evilplan.org> Cc: Junxiao Bi <junxiao.bi@oracle.com> Cc: Changwei Ge <gechangwei@live.cn> Cc: Gang He <ghe@suse.com> Cc: Jun Piao <piaojun@huawei.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The sas_port(phy->port) allocated in sas_ex_discover_expander() will not be
deleted when the expander failed to discover. This will cause resource leak
and a further issue of kernel BUG like below:
Fixes: 2908d778ab3e ("[SCSI] aic94xx: new driver") Reported-by: Jian Luo <luojian5@huawei.com> Signed-off-by: Jason Yan <yanaijie@huawei.com> CC: John Garry <john.garry@huawei.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
If alloc_workqueue fails in alua_init, it should return -ENOMEM, otherwise
it will trigger null-ptr-deref while unloading module which calls
destroy_workqueue dereference
wq->lock like this:
BUG: KASAN: null-ptr-deref in __lock_acquire+0x6b4/0x1ee0
Read of size 8 at addr 0000000000000080 by task syz-executor.0/7045
CPU: 0 PID: 7045 Comm: syz-executor.0 Tainted: G C 5.1.0+ #28
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1ubuntu1
Call Trace:
dump_stack+0xa9/0x10e
__kasan_report+0x171/0x18d
? __lock_acquire+0x6b4/0x1ee0
kasan_report+0xe/0x20
__lock_acquire+0x6b4/0x1ee0
lock_acquire+0xb4/0x1b0
__mutex_lock+0xd8/0xb90
drain_workqueue+0x25/0x290
destroy_workqueue+0x1f/0x3f0
__x64_sys_delete_module+0x244/0x330
do_syscall_64+0x72/0x2a0
entry_SYSCALL_64_after_hwframe+0x49/0xbe
Reported-by: Hulk Robot <hulkci@huawei.com> Fixes: 03197b61c5ec ("scsi_dh_alua: Use workqueue for RTPG") Signed-off-by: YueHaibing <yuehaibing@huawei.com> Reviewed-by: Bart Van Assche <bvanassche@acm.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When SME is enabled, the smartpqi driver won't work on the HP DL385 G10
machine, which causes the failure of kernel boot because it fails to
allocate pqi error buffer. Please refer to the kernel log:
....
[ 9.431749] usbcore: registered new interface driver uas
[ 9.441524] Microsemi PQI Driver (v1.1.4-130)
[ 9.442956] i40e 0000:04:00.0: fw 6.70.48768 api 1.7 nvm 10.2.5
[ 9.447237] smartpqi 0000:23:00.0: Microsemi Smart Family Controller found
Starting dracut initqueue hook...
[ OK ] Started Show Plymouth Boot Scre[ 9.471654] Broadcom NetXtreme-C/E driver bnxt_en v1.9.1
en.
[ OK ] Started Forward Password Requests to Plymouth Directory Watch.
[[0;[ 9.487108] smartpqi 0000:23:00.0: failed to allocate PQI error buffer
....
[ 139.050544] dracut-initqueue[949]: Warning: dracut-initqueue timeout - starting timeout scripts
[ 139.589779] dracut-initqueue[949]: Warning: dracut-initqueue timeout - starting timeout scripts
Basically, the fact that the coherent DMA mask value wasn't set caused the
driver to fall back to SWIOTLB when SME is active.
For correct operation, lets call the dma_set_mask_and_coherent() to
properly set the mask for both streaming and coherent, in order to inform
the kernel about the devices DMA addressing capabilities.
Signed-off-by: Lianbo Jiang <lijiang@redhat.com> Acked-by: Don Brace <don.brace@microsemi.com> Tested-by: Don Brace <don.brace@microsemi.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Ensure that we supply the same phy interface mode to mac_link_down() as
we did for the corresponding mac_link_up() call. This ensures that MAC
drivers that use the phy interface mode in these methods can depend on
mac_link_down() always corresponding to a mac_link_up() call for the
same interface mode.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The sh_eth_close() resets the MAC and then calls phy_stop()
so that mdio read access result is incorrect without any error
according to kernel trace like below:
According to the hardware manual, the RMII mode should be set to 1
before operation the Ethernet MAC. However, the previous code was not
set to 1 after the driver issued the soft_reset in sh_eth_dev_exit()
so that the mdio read access result seemed incorrect. To fix the issue,
this patch adds a condition and set the RMII mode register in
sh_eth_dev_exit() for R-Car Gen2 and RZ/A1 SoCs.
Note that when I have tried to move the sh_eth_dev_exit() calling
after phy_stop() on sh_eth_close(), but it gets worse (kernel panic
happened and it seems that a register is accessed while the clock is
off).
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Calling sys_ni_syscall through a syscall_fn_t pointer trips indirect
call Control-Flow Integrity checking due to a function type
mismatch. Use SYSCALL_DEFINE0 for __arm64_sys_ni_syscall instead and
remove the now unnecessary casts.
Signed-off-by: Sami Tolvanen <samitolvanen@google.com> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Although a syscall defined using SYSCALL_DEFINE0 doesn't accept
parameters, use the correct function type to avoid indirect call
type mismatches with Control-Flow Integrity checking.
Signed-off-by: Sami Tolvanen <samitolvanen@google.com> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Syscall wrappers in <asm/syscall_wrapper.h> use const struct pt_regs *
as the argument type. Use const in syscall_fn_t as well to fix indirect
call type mismatches with Control-Flow Integrity checking.
Signed-off-by: Sami Tolvanen <samitolvanen@google.com> Reviewed-by: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently the HV KVM code takes the kvm->lock around calls to
kvm_for_each_vcpu() and kvm_get_vcpu_by_id() (which can call
kvm_for_each_vcpu() internally). However, that leads to a lock
order inversion problem, because these are called in contexts where
the vcpu mutex is held, but the vcpu mutexes nest within kvm->lock
according to Documentation/virtual/kvm/locking.txt. Hence there
is a possibility of deadlock.
To fix this, we simply don't take the kvm->lock mutex around these
calls. This is safe because the implementations of kvm_for_each_vcpu()
and kvm_get_vcpu_by_id() have been designed to be able to be called
locklessly.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org> Reviewed-by: Cédric Le Goater <clg@kaod.org> Signed-off-by: Paul Mackerras <paulus@ozlabs.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently the Book 3S KVM code uses kvm->lock to synchronize access
to the kvm->arch.rtas_tokens list. Because this list is scanned
inside kvmppc_rtas_hcall(), which is called with the vcpu mutex held,
taking kvm->lock cause a lock inversion problem, which could lead to
a deadlock.
To fix this, we add a new mutex, kvm->arch.rtas_token_lock, which nests
inside the vcpu mutexes, and use that instead of kvm->lock when
accessing the rtas token list.
This removes the lockdep_assert_held() in kvmppc_rtas_tokens_free().
At this point we don't hold the new mutex, but that is OK because
kvmppc_rtas_tokens_free() is only called when the whole VM is being
destroyed, and at that point nothing can be looking up a token in
the list.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
During a suspend/resume, the xenwatch thread waits for all outstanding
xenstore requests and transactions to complete. This does not work
correctly for transactions started by userspace because it waits for
them to complete after freezing userspace threads which means the
transactions have no way of completing, resulting in a deadlock. This is
trivial to reproduce by running this script and then suspending the VM:
import pyxs, time
c = pyxs.client.Client(xen_bus_path="/dev/xen/xenbus")
c.connect()
c.transaction()
time.sleep(3600)
Even if this deadlock were resolved, misbehaving userspace should not
prevent a VM from being migrated. So, instead of waiting for these
transactions to complete before suspending, store the current generation
id for each transaction when it is started. The global generation id is
incremented during resume. If the caller commits the transaction and the
generation id does not match the current generation id, return EAGAIN so
that they try again. If the transaction was instead discarded, return OK
since no changes were made anyway.
This only affects users of the xenbus file interface. In-kernel users of
xenbus are assumed to be well-behaved and complete all transactions
before freezing.
Signed-off-by: Ross Lagerwall <ross.lagerwall@citrix.com> Reviewed-by: Juergen Gross <jgross@suse.com> Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
drivers/xen/pvcalls-front.c: In function pvcalls_front_sendmsg:
drivers/xen/pvcalls-front.c:543:25: warning: variable bedata set but not used [-Wunused-but-set-variable]
drivers/xen/pvcalls-front.c: In function pvcalls_front_recvmsg:
drivers/xen/pvcalls-front.c:638:25: warning: variable bedata set but not used [-Wunused-but-set-variable]
Command 'perf record' and 'perf report' on a system without kernel
debuginfo packages uses /proc/kallsyms and /proc/modules to find
addresses for kernel and module symbols. On x86 this works for root and
non-root users.
On s390, when invoked as non-root user, many of the following warnings
are shown and module symbols are missing:
proc/{kallsyms,modules} inconsistency while looking for
"[sha1_s390]" module!
Command 'perf record' creates a list of module start addresses by
parsing the output of /proc/modules and creates a PERF_RECORD_MMAP
record for the kernel and each module. The following function call
sequence is executed:
machine__create_kernel_maps
machine__create_module
modules__parse
machine__create_module --> for each line in /proc/modules
arch__fix_module_text_start
Function arch__fix_module_text_start() is s390 specific. It opens
file /sys/module/<name>/sections/.text to extract the module's .text
section start address. On s390 the module loader prepends a header
before the first section, whereas on x86 the module's text section
address is identical the the module's load address.
However module section files are root readable only. For non-root the
read operation fails and machine__create_module() returns an error.
Command perf record does not generate any PERF_RECORD_MMAP record
for loaded modules. Later command perf report complains about missing
module maps.
To fix this function arch__fix_module_text_start() always returns
success. For root users there is no change, for non-root users
the module's load address is used as module's text start address
(the prepended header then counts as part of the text section).
This enable non-root users to use module symbols and avoid the
warning when perf report is executed.
This strncat() is safe because the buffer was allocated with zalloc(),
however gcc doesn't know that. Since the string always has 4 non-null
bytes, just use memcpy() here.
CC /home/shawn/linux/tools/perf/util/data-convert-bt.o
In file included from /usr/include/string.h:494,
from /home/shawn/linux/tools/lib/traceevent/event-parse.h:27,
from util/data-convert-bt.c:22:
In function ‘strncat’,
inlined from ‘string_set_value’ at util/data-convert-bt.c:274:4:
/usr/include/powerpc64le-linux-gnu/bits/string_fortified.h:136:10: error: ‘__builtin_strncat’ output may be truncated copying 4 bytes from a string of length 4 [-Werror=stringop-truncation]
136 | return __builtin___strncat_chk (__dest, __src, __len, __bos (__dest));
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Shawn Landden <shawn@git.icu> Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Wang Nan <wangnan0@huawei.com>
LPU-Reference: 20190518183238.10954-1-shawn@git.icu Link: https://lkml.kernel.org/n/tip-289f1jice17ta7tr3tstm9jm@git.kernel.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In the vfs_statx() context, during path lookup, the dentry gets
added to sd->s_dentry via configfs_attach_attr(). In the end,
vfs_statx() kills the dentry by calling path_put(), which invokes
configfs_d_iput(). Ideally, this dentry must be removed from
sd->s_dentry but it doesn't if the sd->s_count >= 3. As a result,
sd->s_dentry is holding reference to a stale dentry pointer whose
memory is already freed up. This results in use-after-free issue,
when this stale sd->s_dentry is accessed later in
configfs_readdir() path.
This issue can be easily reproduced, by running the LTP test case -
sh fs_racer_file_list.sh /config
(https://github.com/linux-test-project/ltp/blob/master/testcases/kernel/fs/racer/fs_racer_file_list.sh)
Fixes: 76ae281f6307 ('configfs: fix race between dentry put and lookup') Signed-off-by: Sahitya Tummala <stummala@codeaurora.org> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
We observed the same issue as reported by commit a8d7bde23e7130686b7662
("ALSA: hda - Force polling mode on CFL for fixing codec communication")
We don't have a better solution. So apply the same workaround to CNL.
Driver stops producing skbs on ring if a packet with FCS error
was coalesced into LRO session. Ring gets hang forever.
Thats a logical error in driver processing descriptors:
When rx_stat indicates MAC Error, next pointer and eop flags
are not filled. This confuses driver so it waits for descriptor 0
to be filled by HW.
Solution is fill next pointer and eop flag even for packets with FCS error.
Fixes: bab6de8fd180b ("net: ethernet: aquantia: Atlantic A0 and B0 specific functions.") Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com> Signed-off-by: Dmitry Bogdanov <dmitry.bogdanov@aquantia.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
In case no other traffic happening on the ring, full tx cleanup
may not be completed. That may cause socket buffer to overflow
and tx traffic to stuck until next activity on the ring happens.
This is due to logic error in budget variable decrementor.
Variable is compared with zero, and then post decremented,
causing it to become MAX_INT. Solution is remove decrementor
from the `for` statement and rewrite it in a clear way.
Fixes: b647d3980948e ("net: aquantia: Add tx clean budget and valid budget handling logic") Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The devcoredump needs to operate on a stable state of the MMU while
it is writing the MMU state to the coredump. The missing lock
allowed both the userspace submit, as well as the GPU job finish
paths to mutate the MMU state while a coredump is under way.
Fixes: a8c21a5451d8 (drm/etnaviv: add initial etnaviv DRM driver) Reported-by: David Jander <david@protonic.nl> Signed-off-by: Lucas Stach <l.stach@pengutronix.de> Tested-by: David Jander <david@protonic.nl> Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
Both acpi_pci_need_resume() and acpi_dev_needs_resume() check if the
current ACPI wakeup configuration of the device matches what is
expected as far as system wakeup from sleep states is concerned, as
reflected by the device_may_wakeup() return value for the device.
However, they only should do that if wakeup.flags.valid is set for
the device's ACPI companion, because otherwise the wakeup.prepare_count
value for it is meaningless.
Add the missing wakeup.flags.valid checks to these functions.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Building with Clang reports the redundant use of MODULE_DEVICE_TABLE():
drivers/net/ethernet/dec/tulip/de4x5.c:2110:1: error: redefinition of '__mod_eisa__de4x5_eisa_ids_device_table'
MODULE_DEVICE_TABLE(eisa, de4x5_eisa_ids);
^
./include/linux/module.h:229:21: note: expanded from macro 'MODULE_DEVICE_TABLE'
extern typeof(name) __mod_##type##__##name##_device_table \
^
<scratch space>:90:1: note: expanded from here
__mod_eisa__de4x5_eisa_ids_device_table
^
drivers/net/ethernet/dec/tulip/de4x5.c:2100:1: note: previous definition is here
MODULE_DEVICE_TABLE(eisa, de4x5_eisa_ids);
^
./include/linux/module.h:229:21: note: expanded from macro 'MODULE_DEVICE_TABLE'
extern typeof(name) __mod_##type##__##name##_device_table \
^
<scratch space>:85:1: note: expanded from here
__mod_eisa__de4x5_eisa_ids_device_table
^
This drops the one further from the table definition to match the common
use of MODULE_DEVICE_TABLE().
Fixes: 07563c711fbc ("EISA bus MODALIAS attributes support") Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently we will not update the receive descriptor tail pointer in
stmmac_rx_refill. Rx dma will think no available descriptors and stop
once received packets exceed DMA_RX_SIZE, so that the rx only test will fail.
Update the receive tail pointer in stmmac_rx_refill to add more descriptors
to the rx channel, so packets can be received continually
Fixes: 54139cf3bb33 ("net: stmmac: adding multiple buffers for rx") Signed-off-by: Biao Huang <biao.huang@mediatek.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The gpio-adp5588 driver uses interfaces that are provided by
GPIOLIB_IRQCHIP, so select that symbol in its Kconfig entry.
Fixes these build errors:
../drivers/gpio/gpio-adp5588.c: In function ‘adp5588_irq_handler’:
../drivers/gpio/gpio-adp5588.c:266:26: error: ‘struct gpio_chip’ has no member named ‘irq’
dev->gpio_chip.irq.domain, gpio));
^
../drivers/gpio/gpio-adp5588.c: In function ‘adp5588_irq_setup’:
../drivers/gpio/gpio-adp5588.c:298:2: error: implicit declaration of function ‘gpiochip_irqchip_add_nested’ [-Werror=implicit-function-declaration]
ret = gpiochip_irqchip_add_nested(&dev->gpio_chip,
^
../drivers/gpio/gpio-adp5588.c:307:2: error: implicit declaration of function ‘gpiochip_set_nested_irqchip’ [-Werror=implicit-function-declaration]
gpiochip_set_nested_irqchip(&dev->gpio_chip,
^
Fixes: 459773ae8dbb ("gpio: adp5588-gpio: support interrupt controller") Reported-by: kbuild test robot <lkp@intel.com> Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Cc: linux-gpio@vger.kernel.org Reviewed-by: Bartosz Golaszewski <bgolaszewski@baylibre.com> Acked-by: Michael Hennerich <michael.hennerich@analog.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Similar to how decrementing rb->next too early can cause data_head to
(temporarily) be observed to go backward, so too can this happen when
we increment too late.
This barrier() ensures the rb->head load happens after the increment,
both the one in the 'goto again' path, as the one from
perf_output_get_handle() -- albeit very unlikely to matter for the
latter.
Suggested-by: Yabin Cui <yabinc@google.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Stephane Eranian <eranian@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Vince Weaver <vincent.weaver@maine.edu> Cc: acme@kernel.org Cc: mark.rutland@arm.com Cc: namhyung@kernel.org Fixes: ef60777c9abd ("perf: Optimize the perf_output() path by removing IRQ-disables") Link: http://lkml.kernel.org/r/20190517115418.309516009@infradead.org Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In perf_output_put_handle(), an IRQ/NMI can happen in below location and
write records to the same ring buffer:
...
local_dec_and_test(&rb->nest)
... <-- an IRQ/NMI can happen here
rb->user_page->data_head = head;
...
In this case, a value A is written to data_head in the IRQ, then a value
B is written to data_head after the IRQ. And A > B. As a result,
data_head is temporarily decreased from A to B. And a reader may see
data_head < data_tail if it read the buffer frequently enough, which
creates unexpected behaviors.
This can be fixed by moving dec(&rb->nest) to after updating data_head,
which prevents the IRQ/NMI above from updating data_head.
[ Split up by peterz. ]
Signed-off-by: Yabin Cui <yabinc@google.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Arnaldo Carvalho de Melo <acme@kernel.org> Cc: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Stephane Eranian <eranian@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Vince Weaver <vincent.weaver@maine.edu> Cc: mark.rutland@arm.com Fixes: ef60777c9abd ("perf: Optimize the perf_output() path by removing IRQ-disables") Link: http://lkml.kernel.org/r/20190517115418.224478157@infradead.org Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
For F17h AMD CPUs, the CPB capability ('Core Performance Boost') is forcibly set,
because some versions of that chip incorrectly report that they do not have it.
However, a hypervisor may filter out the CPB capability, for good
reasons. For example, KVM currently does not emulate setting the CPB
bit in MSR_K7_HWCR, and unchecked MSR access errors will be thrown
when trying to set it as a guest:
unchecked MSR access error: WRMSR to 0xc0010015 (tried to write 0x0000000001000011) at rIP: 0xffffffff890638f4 (native_write_msr+0x4/0x20)
To avoid this issue, don't forcibly set the CPB capability for a CPU
when running under a hypervisor.
Signed-off-by: Frank van der Linden <fllinden@amazon.com> Acked-by: Borislav Petkov <bp@suse.de> Cc: Andy Lutomirski <luto@kernel.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: bp@alien8.de Cc: jiaxun.yang@flygoat.com Fixes: 0237199186e7 ("x86/CPU/AMD: Set the CPB bit unconditionally on F17h") Link: http://lkml.kernel.org/r/20190522221745.GA15789@dev-dsk-fllinden-2c-c1893d73.us-west-2.amazon.com
[ Minor edits to the changelog. ] Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The user can change the device_name with the IMSETDEVNAME ioctl, but we
need to ensure that the user's name is NUL terminated. Otherwise it
could result in a buffer overflow when we copy the name back to the user
with IMGETDEVINFO ioctl.
I also changed two strcpy() calls which handle the name to strscpy().
Hopefully, there aren't any other ways to create a too long name, but
it's nice to do this as a kernel hardening measure.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
In xhci_debugfs_create_slot(), kzalloc() can fail and
dev->debugfs_private will be NULL.
In xhci_debugfs_create_endpoint(), dev->debugfs_private is used without
any null-pointer check, and can cause a null pointer dereference.
To fix this bug, a null-pointer check is added in
xhci_debugfs_create_endpoint().
This bug is found by a runtime fuzzing tool named FIZZER written by us.
Currently init_imc_pmu() can fail either because we try to register an
IMC unit with an invalid domain (i.e an IMC node not supported by the
kernel) or something went wrong while registering a valid IMC unit. In
both the cases kernel provides a 'Register failed' error message.
For example when trace-imc node is not supported by the kernel, but
skiboot advertises a trace-imc node we print:
IMC Unknown Device type
IMC PMU (null) Register failed
To avoid confusion just print the unknown device type message, before
attempting PMU registration, so the second message isn't printed.
Fixes: 8f95faaac56c ("powerpc/powernv: Detect and create IMC device") Reported-by: Pavaman Subramaniyam <pavsubra@in.ibm.com> Signed-off-by: Anju T Sudhakar <anju@linux.vnet.ibm.com> Reviewed-by: Madhavan Srinivasan <maddy@linux.vnet.ibm.com>
[mpe: Reword change log a bit] Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
We need to always call clkdm_clk_enable() and clkdm_clk_disable() even
the clkctrl clock(s) enabled for the domain do not have any gate register
bits. Otherwise clockdomains may never get enabled except when devices get
probed with the legacy "ti,hwmods" devicetree property.
Fixes: 88a172526c32 ("clk: ti: add support for clkctrl clocks") Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
A test for the basic NAT functionality uses ip command which needs veth
device. There is a condition where the kernel support for veth is not
compiled into the kernel and the test script breaks. This patch contains
code for reasonable error display and correct code exit.
Signed-off-by: Jeffrin Jose T <jeffrin@rajagiritech.edu.in> Acked-by: Florian Westphal <fw@strlen.de> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
while unregistering ipvs module, ops_free_list calls
__ip_vs_cleanup, then nf_unregister_net_hooks be called to
do remove nf hook entries. It need a RCU period to finish,
however net->ipvs is set to NULL immediately, which will
trigger NULL pointer dereference when a packet is hooked
and handled by ip_vs_in where net->ipvs is dereferenced.
Another scene is ops_free_list call ops_free to free the
net_generic directly while __ip_vs_cleanup finished, then
calling ip_vs_in will triggers use-after-free.
This patch moves nf_unregister_net_hooks from __ip_vs_cleanup()
to __ip_vs_dev_cleanup(), where rcu_barrier() is called by
unregister_pernet_device -> unregister_pernet_operations,
that will do the needed grace period.
Reported-by: Hulk Robot <hulkci@huawei.com> Fixes: efe41606184e ("ipvs: convert to use pernet nf_hook api") Suggested-by: Julian Anastasov <ja@ssi.bg> Signed-off-by: YueHaibing <yuehaibing@huawei.com> Acked-by: Julian Anastasov <ja@ssi.bg> Signed-off-by: Simon Horman <horms@verge.net.au> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
This patch fixes netfilter hook traversal when there are more than 1 hooks
returning NF_QUEUE verdict. When the first queue reinjects the packet,
'nf_reinject' starts traversing hooks with a proper hook_index. However,
if it again receives a NF_QUEUE verdict (by some other netfilter hook), it
queues the packet with a wrong hook_index. So, when the second queue
reinjects the packet, it re-executes hooks in between.
Fixes: 960632ece694 ("netfilter: convert hook list to an array") Signed-off-by: Jagdish Motwani <jagdish.motwani@sophos.com> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
That patch modified INTEL_FLAGS_EVENT_CONSTRAINT() to only look at the event code
when matching a constraint. If code+umask were needed, then the
INTEL_FLAGS_UEVENT_CONSTRAINT() macro was needed instead.
This broke with some of the constraints for PEBS events.
Several of them, including the one used for cycles:p, cycles:pp, cycles:ppp
fell in that category and caused the event to be rejected in PEBS mode.
In other words, on some platforms a cmdline such as:
$ perf top -e cycles:pp
would fail with -EINVAL.
This patch fixes this bug by properly using INTEL_FLAGS_UEVENT_CONSTRAINT()
when needed in the PEBS constraint tables.
Reported-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Stephane Eranian <eranian@google.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Vince Weaver <vincent.weaver@maine.edu> Cc: kan.liang@intel.com Link: http://lkml.kernel.org/r/20190521005246.423-1-eranian@google.com Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When removing all VID filters, the mvpp2_prs_vid_entry_remove would be
called with the TCAM id incorrectly used as a VID, causing the wrong
TCAM entries to be invalidated.
Fix this by directly invalidating entries in the VID range.
Fixes: 56beda3db602 ("net: mvpp2: Add hardware offloading for VLAN filtering") Suggested-by: Yuri Chipchev <yuric@marvell.com> Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alaa Hleihel [Sun, 19 May 2019 08:11:49 +0000 (11:11 +0300)]
net/mlx5: Avoid reloading already removed devices
Prior to reloading a device we must first verify that it was not already
removed. Otherwise, the attempt to remove the device will do nothing, and
in that case we will end up proceeding with adding an new device that no
one was expecting to remove, leaving behind used resources such as EQs that
causes a failure to destroy comp EQs and syndrome (0x30f433).
Fix that by making sure that we try to remove and add a device (based on a
protocol) only if the device is already added.
Set the SOCK_DONE flag to match the TCP_CLOSING state when a peer has
shut down and there is nothing left to read.
This fixes the following bug:
1) Peer sends SHUTDOWN(RDWR).
2) Socket enters TCP_CLOSING but SOCK_DONE is not set.
3) read() returns -ENOTCONN until close() is called, then returns 0.
Signed-off-by: Stephen Barber <smbarber@chromium.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Syzbot reported a memleak caused by grp members' deferredq list not
purged when the grp is be deleted.
The issue occurs when more(msg_grp_bc_seqno(hdr), m->bc_rcv_nxt) in
tipc_group_filter_msg() and the skb will stay in deferredq.
So fix it by calling __skb_queue_purge for each member's deferredq
in tipc_group_delete() when a tipc sk leaves the grp.
Fixes: b87a5ea31c93 ("tipc: guarantee group unicast doesn't bypass group broadcast") Reported-by: syzbot+78fbe679c8ca8d264a8d@syzkaller.appspotmail.com Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In d5a2aa24, the name in struct console sunhv_console was changed from "ttyS"
to "ttyHV" while the name in struct uart_ops sunhv_pops remained unchanged.
This results in the hypervisor console device to be listed as "ttyHV0" under
/proc/consoles while the device node is still named "ttyS0":
root@osaka:~# cat /proc/consoles
ttyHV0 -W- (EC p ) 4:64
tty0 -WU (E ) 4:1
root@osaka:~# readlink /sys/dev/char/4:64
../../devices/root/f02836f0/f0285690/tty/ttyS0
root@osaka:~#
This means that any userland code which tries to determine the name of the
device file of the hypervisor console device can not rely on the information
provided by /proc/consoles. In particular, booting current versions of debian-
installer inside a SPARC LDOM will fail with the installer unable to determine
the console device.
After renaming the device in struct uart_ops sunhv_pops to "ttyHV" as well,
the inconsistency is fixed and it is possible again to determine the name
of the device file of the hypervisor console device by reading the contents
of /proc/console:
root@osaka:~# cat /proc/consoles
ttyHV0 -W- (EC p ) 4:64
tty0 -WU (E ) 4:1
root@osaka:~# readlink /sys/dev/char/4:64
../../devices/root/f02836f0/f0285690/tty/ttyHV0
root@osaka:~#
With this change, debian-installer works correctly when installing inside
a SPARC LDOM.
Signed-off-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on comments from Xin, even after fixes for our recent syzbot
report of cookie memory leaks, its possible to get a resend of an INIT
chunk which would lead to us leaking cookie memory.
To ensure that we don't leak cookie memory, free any previously
allocated cookie first.
Change notes
v1->v2
update subsystem tag in subject (davem)
repeat kfree check for peer_random and peer_hmacs (xin)
v2->v3
net->sctp
also free peer_chunks
v3->v4
fix subject tags
v4->v5
remove cut line
Signed-off-by: Neil Horman <nhorman@tuxdriver.com> Reported-by: syzbot+f7e9153b037eac9b1df8@syzkaller.appspotmail.com CC: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> CC: Xin Long <lucien.xin@gmail.com> CC: "David S. Miller" <davem@davemloft.net> CC: netdev@vger.kernel.org Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Check that the NFC_ATTR_TARGET_INDEX attributes (in addition to
NFC_ATTR_DEVICE_INDEX) are provided by the netlink client prior to
accessing them. This prevents potential unhandled NULL pointer dereference
exceptions which can be triggered by malicious user-mode programs,
if they omit one or both of these attributes.
Signed-off-by: Young Xiao <92siuyang@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order to create an internal vport, internal_dev_create() is used and
that calls register_netdevice() internally.
If register_netdevice() fails, it calls dev->priv_destructor() to free
private data of netdev. actually, a private data of this is a vport.
Hence internal_dev_create() should not free and use a vport after failure
of register_netdevice().
Fixes: cf124db566e6 ("net: Fix inconsistent teardown and release of private netdev state.") Signed-off-by: Taehee Yoo <ap420073@gmail.com> Reviewed-by: Greg Rose <gvrose8192@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We get this regression when using RTL8366RB as part of a bridge
with OpenWrt:
WARNING: CPU: 0 PID: 1347 at net/switchdev/switchdev.c:291
switchdev_port_attr_set_now+0x80/0xa4
lan0: Commit of attribute (id=7) failed.
(...)
realtek-smi switch lan0: failed to initialize vlan filtering on this port
This is because it is trying to disable VLAN filtering
on VLAN0, as we have forgot to add 1 to the port number
to get the right VLAN in rtl8366_vlan_filtering(): when
we initialize the VLAN we associate VLAN1 with port 0,
VLAN2 with port 1 etc, so we need to add 1 to the port
offset.
Fixes: d8652956cf37 ("net: dsa: realtek-smi: Add Realtek SMI driver") Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Nine years ago, I added RCU handling to neighbours, not pneighbours.
(pneigh are not commonly used)
Unfortunately I missed that /proc dump operations would use a
common entry and exit point : neigh_seq_start() and neigh_seq_stop()
We need to read_lock(tbl->lock) or risk use-after-free while
iterating the pneigh structures.
We might later convert pneigh to RCU and revert this patch.
sysbot reported :
BUG: KASAN: use-after-free in pneigh_get_next.isra.0+0x24b/0x280 net/core/neighbour.c:3158
Read of size 8 at addr ffff888097f2a700 by task syz-executor.0/9825
Memory state around the buggy address: ffff888097f2a600: 00 00 00 00 00 00 00 00 fc fc fc fc fc fc fc fc ffff888097f2a680: fb fb fb fb fb fb fb fb fc fc fc fc fc fc fc fc
>ffff888097f2a700: fb fb fb fb fb fb fb fb fc fc fc fc fc fc fc fc
^ ffff888097f2a780: fb fb fb fb fb fb fb fb fc fc fc fc fc fc fc fc ffff888097f2a800: fb fb fb fb fb fb fb fb fc fc fc fc fc fc fc fc
Fixes: 767e97e1e0db ("neigh: RCU conversion of struct neighbour") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
lapb_register calls lapb_create_cb, which initializes the control-
block's ref-count to one, and __lapb_insert_cb, which increments it when
adding the new block to the list of blocks.
lapb_unregister calls __lapb_remove_cb, which decrements the ref-count
when removing control-block from the list of blocks, and calls lapb_put
itself to decrement the ref-count before returning.
However, lapb_unregister also calls __lapb_devtostruct to look up the
right control-block for the given net_device, and __lapb_devtostruct
also bumps the ref-count, which means that when lapb_unregister returns
the ref-count is still 1 and the control-block is leaked.
Call lapb_put after __lapb_devtostruct to fix leak.
Reported-by: syzbot+afb980676c836b4a0afa@syzkaller.appspotmail.com Signed-off-by: Jeremy Sowden <jeremy@azazel.net> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Before taking a refcount, make sure the object is not already
scheduled for deletion.
Same fix is needed in ipv6_flowlabel_opt()
Fixes: 18367681a10b ("ipv6 flowlabel: Convert np->ipv6_fl_list to RCU.") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For better consistency of synthetic NIC names, we set the probe mode to
PROBE_FORCE_SYNCHRONOUS. So the names can be aligned with the vmbus
channel offer sequence.
Fixes: af0a5646cb8d ("use the new async probing feature for the hyperv drivers") Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Number of Rx queues used for flow hashing returned by the driver is
incorrect and this bug prevents user to use the last Rx queue in
indirection table.
Fixes: 594ad54a2c3b ("be2net: Add support for setting and getting rx flow hash options") Reported-by: Tianhao <tizhao@redhat.com> Signed-off-by: Ivan Vecera <ivecera@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The RTC_VL_READ ioctl reports the low battery condition. Still,
pcf8523_rtc_read_time() happily returns invalid dates in this case.
Check the battery health on pcf8523_rtc_read_time() to avoid that.
We've moved the override and firmware EDID (simply "override EDID" from
now on) handling to the low level drm_do_get_edid() function in order to
transparently use the override throughout the stack. The idea is that
you get the override EDID via the ->get_modes() hook.
Unfortunately, there are scenarios where the DDC probe in drm_get_edid()
called via ->get_modes() fails, although the preceding ->detect()
succeeds.
In the case reported by Paul Wise, the ->detect() hook,
intel_crt_detect(), relies on hotplug detect, bypassing the DDC. In the
case reported by Ilpo Järvinen, there is no ->detect() hook, which is
interpreted as connected. The subsequent DDC probe reached via
->get_modes() fails, and we don't even look at the override EDID,
resulting in no modes being added.
Because drm_get_edid() is used via ->detect() all over the place, we
can't trivially remove the DDC probe, as it leads to override EDID
effectively meaning connector forcing. The goal is that connector
forcing and override EDID remain orthogonal.
Generally, the underlying problem here is the conflation of ->detect()
and ->get_modes() via drm_get_edid(). The former should just detect, and
the latter should just get the modes, typically via reading the EDID. As
long as drm_get_edid() is used in ->detect(), it needs to retain the DDC
probe. Or such users need to have a separate DDC probe step first.
The EDID caching between ->detect() and ->get_modes() done by some
drivers is a further complication that prevents us from making
drm_do_get_edid() adapt to the two cases.
Work around the regression by falling back to a separate attempt at
getting the override EDID at drm_helper_probe_single_connector_modes()
level. With a working DDC and override EDID, it'll never be called; the
override EDID will come via ->get_modes(). There will still be a failing
DDC probe attempt in the cases that require the fallback.
Booting with kernel parameter "rdt=cmt,mbmtotal,memlocal,l3cat,mba" and
executing "mount -t resctrl resctrl -o mba_MBps /sys/fs/resctrl" results in
a NULL pointer dereference on systems which do not have local MBM support
enabled..
The size of the vmemmap section is hardcoded to 1 TB to support the
maximum amount of system RAM in 4-level paging mode - 64 TB.
However, 1 TB is not enough for vmemmap in 5-level paging mode. Assuming
the size of struct page is 64 Bytes, to support 4 PB system RAM in 5-level,
64 TB of vmemmap area is needed:
This hardcoding may cause vmemmap to corrupt the following
cpu_entry_area section, if KASLR puts vmemmap very close to it and the
actual vmemmap size is bigger than 1 TB.
So calculate the actual size of the vmemmap region needed and then align
it up to 1 TB boundary.
In 4-level paging mode it is always 1 TB. In 5-level it's adjusted on
demand. The current code reserves 0.5 PB for vmemmap on 5-level. With
this change, the space can be saved and thus used to increase entropy
for the randomization.
[ bp: Spell out how the 64 TB needed for vmemmap is computed and massage commit
message. ]
Fixes: eedb92abb9bb ("x86/mm: Make virtual memory layout dynamic for CONFIG_X86_5LEVEL=y") Signed-off-by: Baoquan He <bhe@redhat.com> Signed-off-by: Borislav Petkov <bp@suse.de> Reviewed-by: Kees Cook <keescook@chromium.org> Acked-by: Kirill A. Shutemov <kirill@linux.intel.com> Cc: Andy Lutomirski <luto@kernel.org> Cc: Dave Hansen <dave.hansen@linux.intel.com> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Ingo Molnar <mingo@kernel.org> Cc: kirill.shutemov@linux.intel.com Cc: Peter Zijlstra <peterz@infradead.org> Cc: stable <stable@vger.kernel.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: x86-ml <x86@kernel.org> Link: https://lkml.kernel.org/r/20190523025744.3756-1-bhe@redhat.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit d52888aa2753 ("x86/mm: Move LDT remap out of KASLR region on
5-level paging") kernel doesn't boot with KASAN on 5-level paging machines.
The bug is actually in early_p4d_offset() and introduced by commit 12a8cc7fcf54 ("x86/kasan: Use the same shadow offset for 4- and 5-level paging")
early_p4d_offset() tries to convert pgd_val(*pgd) value to a physical
address. This doesn't make sense because pgd_val() already contains the
physical address.
It did work prior to commit d52888aa2753 because the result of
"__pa_nodebug(pgd_val(*pgd)) & PTE_PFN_MASK" was the same as "pgd_val(*pgd)
& PTE_PFN_MASK". __pa_nodebug() just set some high bits which were masked
out by applying PTE_PFN_MASK.
After the change of the PAGE_OFFSET offset in commit d52888aa2753
__pa_nodebug(pgd_val(*pgd)) started to return a value with more high bits
set and PTE_PFN_MASK wasn't enough to mask out all of them. So it returns a
wrong not even canonical address and crashes on the attempt to dereference
it.
Switch back to pgd_val() & PTE_PFN_MASK to cure the issue.
Fixes: 12a8cc7fcf54 ("x86/kasan: Use the same shadow offset for 4- and 5-level paging") Reported-by: Kirill A. Shutemov <kirill@shutemov.name> Signed-off-by: Andrey Ryabinin <aryabinin@virtuozzo.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Borislav Petkov <bp@alien8.de> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Alexander Potapenko <glider@google.com> Cc: Dmitry Vyukov <dvyukov@google.com> Cc: kasan-dev@googlegroups.com Cc: stable@vger.kernel.org Cc: <stable@vger.kernel.org> Link: https://lkml.kernel.org/r/20190614143149.2227-1-aryabinin@virtuozzo.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / thirdparty / kernel / stable.git / log
