x86/base-files: add support for CloudGenix ION 2000
The CloudGenix ION 2000 is a discontinued entry-level SD-WAN appliance,
a rebranded Lanner FW-7525 based on the Intel Atom C2XXX family of processors
with 4 integrated GbE ports and 2 additional I210 GbE ports. It can often be
found on eBay starting below USD 30.
The device's BIOS is password-protected, and the password somehow hasn't leaked,
but OpenWrt can be successfully booted by overwriting the stock OS on the boot
media.
See https://forum.openwrt.org/t/report-openwrt-on-cloudgenix-ion-2000/249315
for more details.
The two I210 NICs and integrated NICs are pinned to their
PCIe paths to ensure consistent interface ordering matching
the physical port layout with eth0 assigned to controller and
acting as WAN with remaining devices as LAN.
Rosen Penev [Thu, 4 Dec 2025 03:15:05 +0000 (19:15 -0800)]
ath79: fix label-mac-device for wmac
It appears 683-of_net-add-mac-address-to-of-tree.patch relies on the
mac-address nvmem property being present. wmac itself doesn't need it as
it takes it from the eeprom but label-mac-device needs it.
Ahmed Naseef [Thu, 19 Mar 2026 11:55:28 +0000 (15:55 +0400)]
econet: en7528: add USB support
Add USB host support for EN7528 SoC:
- New phy-en7528-usb driver with U2 slew rate calibration and U3
RX impedance tuning, based on GPL vendor code and the Airoha
AN7581 USB PHY driver
- xHCI LTSSM timing quirk for TD 6.5 compliance (patch 915)
- USB PHY and xHCI DTS nodes with IPPC register mapping
- VBUS power via regulator-fixed for DASAN H660GM-A
- Enable USB, xHCI, PHY, and regulator kernel configs
kmod-sound-midi2 expects sound/core/snd-ump.ko, but
CONFIG_SND_UMP=y builds it in-kernel rather than as
a module. Replace the forced built-in setting with
plain CONFIG_SND_UMP so the module can be packaged
correctly.
mediatek: add support for Qihoo 360T7 (UBI layout)
This commit adds support for Qihoo 360T7 (UBI layout).
Aims
----
1. +20 MB additional free space for the packages
2. More reliable storage for the factory and fip partitions (in UBI)
Install (from non-UBI OpenWrt)
------------------------------
1. Navigate http://192.168.1.1/ and download mtd backups
2. Upgrade OpenWrt with installer initramfs image (force upgrade, don't
keep settings). Wait until OpenWrt reboots and until installer:
- Prepare new factory partition
- Format new ubi
- Make ubi volumes
- Write new fip and bl2
3. Navigate http://192.168.1.1/ and Upgrade with OpenWrt 'sysupgrade.bin'
image (don't keep settings)
Qingfang Deng [Fri, 24 Apr 2026 01:44:32 +0000 (09:44 +0800)]
kernel: enable static key
Enable static key (jump label) on all supported architectures. This
lowers overhead and stress on the branch prediction of the CPU and
generally makes the kernel faster.
mediatek,mtd-eeprom predates nvmem and is being phased out.
At first glance, it looks like it's doing something useful with its
big-endian binding. However on further inspection, big-endian is handled
in the same function that mediatek,mtd-eeprom is handled. In addition,
the older mtd_read way of extracting the firmware byteswaps the data
on big endian hosts which big-endian byteswaps back. nvmem does not do
such byteswapping.
Zoltan HERPAI [Mon, 9 Feb 2026 09:34:37 +0000 (09:34 +0000)]
sunxi: add T113-S3 support
The Allwinner T113-s3 (sun8i) SoC features a dual-core Cortex-A7 ARM CPU and
128MB of DDR3 memory in the same physical package. It supports industrial
temperature ranges. Most of the IP blocks are shared with the D1/D1s core.
There are multiple variants of the SoC, which may vary in the included memory
size, with some of them including a C906 RISC-V co-processor.
This is an automatically generated commit which aids following Kernel patch
history, as git will see the move and copy as a rename thus defeating the
purpose.
For the original discussion see:
https://lists.openwrt.org/pipermail/openwrt-devel/2023-October/041673.html
Til Kaiser [Sun, 1 Feb 2026 15:42:46 +0000 (16:42 +0100)]
ipq40xx: refresh IPQ4019 switch patch for v6.18
Linux 6.18 adjusts the DSA/phylink integration and removes a couple of
interfaces used by the out-of-tree IPQ4019 built-in switch support.
Update the qca8k-ipq4019 patch to match the new APIs:
- move phylink callbacks to phylink_mac_ops and switch to phylink_config
[1], [2]
- adapt pcs_get_state() to the new signature [3]
- drop get_mac_eee() from dsa_switch_ops [4]
- switch platform_driver from .remove_new to .remove [5]
Til Kaiser [Fri, 27 Feb 2026 19:46:15 +0000 (20:46 +0100)]
kernel/ipq40xx: restore files for v6.12
This is an automatically generated commit which aids following Kernel patch
history, as git will see the move and copy as a rename thus defeating the
purpose.
For the original discussion see:
https://lists.openwrt.org/pipermail/openwrt-devel/2023-October/041673.html
A script was ran that checks the label-mac-device node to see if it has
nvmem definitions as label-mac-device requires nvmem.
This is mostly a change to make the script happy. No indended functional
difference.
Add a change to qca9533_yuncore_cpe830.dts adding an nvmem definition to
wmac. Seems to have been some kind of oversight where it's specified in
nvmem but not used. label-mac-device needs an NVMEM definition.
On 25.12.0 the device has not enough free blocks to initialize overlay.
Move the device to tiny target and consume backup with storage
partitions, which were previously unused. This operation will reclaim
~800 KiB of flash memory. OEM used storage partition for configuration,
while backup was used to store copy of U-Boot environment and copy of
calibration data.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Partially revert 5e3a602def72. Unfortunately the ethaddr value in U-Boot
environment is enclosed in double quotes which makes it longer than
ETH_ALEN, thus nvmem returns EINVAL. Switch back to handling the MAC
addresses in user space.
Fixes: 5e3a602def72 ("ath79: sitecom,wlrx100: use nvmem") Reviewed-by: Rosen Penev <rosenp@gmail.com> Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Rosen Penev [Sat, 2 May 2026 21:41:43 +0000 (14:41 -0700)]
ath79: use led-sources for WMAC
The ath9k driver creates an ath9k LED by default. Instead of having a
non functional LED, configure it properly and remove the extra as it's
not needed.
It's also a bit funny matching against phy0 and phy1 when both differ
between ath9k and ath10k.
Rosen Penev [Sun, 3 May 2026 21:14:32 +0000 (14:14 -0700)]
ath79: fap-221-b: revert led-sources change
Normally WMAC handles 2.4ghz on ath79 devices. Some older units though
handle 5ghz on WMAC and 2.4ghz on pcie. This can be seen by the
frequemcy limits placed on each interface.
Rosen Penev [Sat, 24 May 2025 23:02:54 +0000 (16:02 -0700)]
ath79: qca953x: use led-sources for WMAC
The ath9k driver creates an ath9k LED by default. Instead of having a
non functional LED, configure it properly and remove the extra as it's
not needed.
It's also a bit funny matching against phy0 and phy1 when both differ
between ath9k and ath10k.
Rosen Penev [Sun, 25 May 2025 00:40:41 +0000 (17:40 -0700)]
ath79: qca955x: use led-sources for WMAC
The ath9k driver creates an ath9k LED by default. Instead of having a
non functional LED, configure it properly and remove the extra as it's
not needed.
It's also a bit funny matching against phy0 and phy1 when both differ
between ath9k and ath10k.
realtek: mach/prom: add identifiers to soc_info structure
SoC name and system type identifiers are currently separated from
the soc_info structure. This gives no benefit. Relocate that info
into the structure where it belongs.
Jonas Jelonek [Mon, 27 Apr 2026 10:34:27 +0000 (10:34 +0000)]
realtek: pcs: rtl93xx: share IP mode register write
RTL930x and RTL931x program the same physical SerDes IP mode field
(page 0x1f reg 0x09, bits 11:7 hold the 5-bit mode value, bit 6 is
the "force mode" enable), but did so via two unrelated code paths:
RTL930x kept the force bit separate from the value in a __set helper,
while RTL931x had it baked into each switch-case constant.
Add a shared rtpcs_93xx_sds_set_ip_mode() that takes the rtpcs_sds_mode
enum, looks up the 5-bit value from the existing sds_hw_mode_vals
table, and writes value | force-bit in one place.
Convert both variants:
- RTL930x: drop __rtpcs_930x_sds_set_ip_mode and the manual table
lookup; __rtpcs_930x_sds_get_ip_mode is replaced by the shared
rtpcs_93xx_sds_get_ip_mode, which reverse-looks the raw register
value up in sds_hw_mode_vals[] and returns the matching enum
rtpcs_sds_mode (or -ENOENT for an unmapped raw value). The
wrapper that orchestrates power, CMU, state machine and rx-reset
around the mode write is renamed to rtpcs_930x_sds_apply_ip_mode
for clarity.
- RTL931x: drop the per-mode switch and the leftover pr_info debug
print; rename the symerr-clear + MAC-OFF + IP-mode-write wrapper
to rtpcs_931x_sds_apply_ip_mode.
rtpcs_930x_sds_reconfigure_to_pll() now goes through the new shared
get/set helpers: it saves the current IP mode as an enum on entry
and restores it via the enum-taking setter after the PLL reconfigure.
This changes behavior by mapping the raw mode setting through the
hardware mode table, effectively blocking unknown modes which might be
set by bootloader or somewhere else. This is intended and might uncover
unknown behavior instead of hiding it.
As a side-effect, QSGMII is now properly set too for RTL931x. Most code
paths anyway already had support for this mode, but it was missing from
the mode setting.
Christoph Krapp [Mon, 4 May 2026 07:23:13 +0000 (09:23 +0200)]
ath79: add calibration variant for TP-Link EAP225-Wall v2
Now that we have a board file, add calibration variant for TP-Link
EAP225-Wall v2 and add ipq-wifi package for it.
Tested-by: Alexander <52272120+alexxela1337@users.noreply.github.com> Signed-off-by: Christoph Krapp <achterin@gmail.com> Link: https://github.com/openwrt/openwrt/pull/23216 Signed-off-by: Robert Marko <robimarko@gmail.com>
Jonas Jelonek [Thu, 30 Apr 2026 10:55:36 +0000 (10:55 +0000)]
realtek: image: reset COMPILE between devices
Device/zyxel_zynos sets COMPILE := loader-$(1).bin to drive the
standalone rt-loader build, but include/image.mk's Device/Init does
not reset COMPILE between TARGET_DEVICES iterations. When a non-zynos
device follows a zynos device, the stale COMPILE entry survives and
Device/Build/compile registers a second recipe for the previous
device's loader-*.bin target. Make warns about the override and the
second (wrong) recipe wins.
Reset COMPILE in Device/Default so each device starts with a clean
slate.
Jonas Jelonek [Thu, 30 Apr 2026 10:54:33 +0000 (10:54 +0000)]
realtek: image: pin FLASH_ADDR per device
FLASH_ADDR is referenced inside Build/rt-loader-standalone but is not
listed in DEVICE_VARS, so include/image.mk's Device/Export does not
emit a per-target FLASH_ADDR := <value> assignment for the standalone
loader recipe. At recipe expansion time $(FLASH_ADDR) therefore
resolves to whatever value the last device in TARGET_DEVICES set
globally, which is not necessarily the value belonging to the loader
being built.
This currently happens to produce correct binaries only because every
device that sets FLASH_ADDR within a given subtarget shares the same
value, so the leaked global matches by coincidence.
Add FLASH_ADDR to DEVICE_VARS so each loader recipe captures its own
device's address.
Zoltan HERPAI [Tue, 5 May 2026 22:41:54 +0000 (22:41 +0000)]
starfive: 6.18: update LED aliases
Between 6.12 and 6.18, a 'blank' led_status_power has been added into
jh7110-common.dtsi. Update the patches responsible for adding the LED
aliases and add functionality for this LED entry.
The mdio driver has found a simple way to handle phy addresses
for all devices with upstream kernel defaults. Remove all unneeded
hacks from the corresponding patch and reword it.
While we are here increase DSA_MAX_PORTS to 56 to match RTL931x.
- mdio bus 0 serves ports 0..23
- mdio bus 1 serves ports 24..51
This is baked into hardware and cannot be changed during mdio driver
setup with any register write. With the recent changes the driver
handles ports, phys and busses in a more logical way. So a port X
is assigned to a bus Y and a phy Z (on that bus). This gives a
mapping like
- port 16 <=> bus 0, address 16
- port 32 <=> bus 1, address 8
This unique assignment is used in the mdio driver as follows:
- Request to read bus 1, address 8
- Lookup corresponding port = 32
- Read from port 32
Looking at RTL839x it becomes clear that bus/phy => port lookup can
be achieved in multiple different ways. The simple reason is, that
for this device the driver cannot setup the smi topology. It is
baked into the hardware. So adding a "virtual" second bus does not
change the hardware access but allows to keep phy addresses below 32.
Making an example
mdio_bus0 {
PHY_C22(40, 40)
}
resolves to port 40. But the same can be achieved with
mdio_bus1 {
PHY_C22(40, 16)
}
In the first case the kernel sees bus/phy = 0/40 and in the second
case it sees bus/phy = 1/16. Both result in the access to the same
phy device on hardware port 40.
Use this analogy for RTL839x devices to match the real hardware
topology. For this change the existing dts and
- activate mdio bus 1 in rtl839x.dtsi
- rearrange devices with ports 24..51 to make use of bus 1
The lm75 alert polarity active-high patch has been accepted upstream.
Replace the downstream version. Additionally add an upstream bugfix
that was identified during the implementation.
Edward Chow [Mon, 27 Apr 2026 03:13:51 +0000 (11:13 +0800)]
mpc85xx: unify wrapper address of simple image devices
The wrapper address of simple image devices should have been changed
at commit 6a8b831 , but only TL-WDR4900 and BR200-WP are changed at
that time, and now the wrapper address changes are split among patches
for specific devices. More importantly, commit 6a8b831 forgot to
change Enterasys WS-AP3715i, causing
https://github.com/openwrt/openwrt/issues/23112 .
This commit will gather the change of wrapper address of simple image
devices into a dedicated patch file.
Tested: Both WS-AP3715i and TL-WDR4900 v1 boot well.
Fixes: https://github.com/openwrt/openwrt/issues/23112 Signed-off-by: Edward Chow <equu@openmail.cc> Link: https://github.com/openwrt/openwrt/pull/23121 Signed-off-by: Robert Marko <robimarko@gmail.com>
Edward Chow [Wed, 29 Apr 2026 21:52:10 +0000 (05:52 +0800)]
mpc85xx: ws-ap3715i: use libdeflate-gzip for kernel
The simpleImage contains a payload already compressed with lzma-based
xz (by default), so further compressing it with lzma will often make
the result larger. On the contrary, compressing these simpleImages
with gzip can make the result smaller, so replace lzma with
libdeflate-gzip to compress kernel for ws-ap3715i.
Edward Chow [Tue, 28 Apr 2026 03:29:01 +0000 (11:29 +0800)]
mpc85xx: ws-ap3715i: enable access to u-boot env
find_mtd_part() outputs /dev/mtdblockX, to which fw_setenv cannot
write, "/dev/mtd$(find_mtd_index '<vol name>')" could be used instead.
The envsize should also be changed to 0x1000 to make the CRC checksum
valid and the env block recognized by the uboot-envtools, but the
flash sector size remains 0x10000, otherwise the env block will be
readable but not writable.
The "read-only" mark within device tree is also removed.
Add the basic bits to allow 100base-FX SFP mode on the RTL8214FC.
While this looks good fom ethtool perspective, it does not really
change the phy registers to enforce the mode. The SFP is still
driven in 1000base-X.
While it might seem useless at the moment this at least opens
up a new phy control method. This comes handy with one known bug.
In rare cases a SFP that is plugged in during boot does not get
a link. One option to revive the dead port seems to be
root@OpenWrt:~# ethtool -s lan28 speed 100 duplex full autoneg off
rtl83xx-switch 1b000000.switchcore:ethernet-switch lan28: Link is Up - 100Mbps/Full - flow control off
switch: port 28(lan28) entered blocking state
switch: port 28(lan28) entered forwarding state
rtl83xx_fib_event: FIB_RULE ADD/DEL for IPv6 not supported
rtl83xx_fib_event: FIB_RULE ADD/DEL for IPv6 not supported
Maximum devnum in c45 access is only 31. The bits 21-31 of the MMD
register are reserved and cannot be written. Nevertheless add a
proper mask to help AI review bots.
rtmdio_probe_one() should be only called by rtmdio_probe() after it
has validated the dts input. Nevertheless be defensive and add
another consistency check.
Rename the module to describe that it is for the Realtek Otto
switches. Add owner to make clear who takes care. Adapt the
license to match the SPDX header.
realtek: mdio: avoid access to uninitialized variable
The read functions might fail and thus "val" might be uninitialized.
The debug function will output the undefined state. Set the value
to zero to be consistent.
realtek: mdio: add define for RTL839x C22 reads/writes
The RTL839x allows to add an extended page operator during phy
access. This is not needed for the standard linux kernel C22
access. Give the hardcoded 0x1ff value a meaningful define.
Although it is not needed, add the corresponding register define.
This makes clear where the mask belongs to.
realtek: mdio: focus on c22/c45 bits in rtmdio_931x_setup_ctrl()
The rtmdio_931x_setup_ctrl() function currently initializes the c22/c45
and the proprietary format bit of the controller. This works because of
the order these calls are arranged. Narrow down the update to the really
needed bits.
- c22/c45 (bit 1) is updated here
- standard/proprietary (bit 0) is updated in rtmdio_931x_setup_polling()
Adapt the confusing comment "Std. C45, non-standard is 0x3" it basically
explains the other function.
realtek: mdio: refactor RTL930x port ability setup
Provide a separate function to setup the ability (SDS/MDIO) of a RTL930x
port. This simplifies rtmdio_930x_setup_polling(). With this commit the
driver does no longer unconditionally overwrite reserved register bits.
Add a return value for the new function to indicate failure/success. As
of now this will be silently ignored in the caller. A future commit will
take care about that.
realtek: mdio: refactor RTL931x port ability setup
Provide a separate function to setup the ability (SDS/MDIO) of a RTL931x
port. This simplifies rtmdio_931x_setup_polling(). With this commit the
driver does no longer unconditionally overwrite reserved register bits.
Add a return value for the new function to indicate failure/success. As
of now this will be silently ignored in the caller. A future commit will
take care about that.
projects / thirdparty / openwrt.git / log
