wifi: iwlwifi: mld: send tx power constraints before link activation
TX power constraints must be sent to the firmware before link
activation. If not, the firmware will use default power values.
Fix this by moving the iwl_mld_send_ap_tx_power_constraint_cmd()
call from iwl_mld_start_ap_ibss() to iwl_mld_assign_vif_chanctx(),
before iwl_mld_activate_link() for AP interfaces. Also update
the guard in the function to allow it to run before link activation
for AP interfaces.
All buses have been converted from driver_set_override() to the generic
driver_override infrastructure introduced in commit cb3d1049f4ea
("driver core: generalize driver_override in struct device").
Buses now either opt into the generic sysfs callbacks via the
bus_type::driver_override flag, or use device_set_driver_override() /
__device_set_driver_override() directly.
Thus, remove the now-unused driver_set_override() helper.
When a driver is probed through __driver_attach(), the bus' match()
callback is called without the device lock held, thus accessing the
driver_override field without a lock, which can cause a UAF.
Fix this by using the driver-core driver_override infrastructure taking
care of proper locking internally.
Note that calling match() from __driver_attach() without the device lock
held is intentional. [1]
Drivers: hv: vmbus: use generic driver_override infrastructure
When a driver is probed through __driver_attach(), the bus' match()
callback is called without the device lock held, thus accessing the
driver_override field without a lock, which can cause a UAF.
Fix this by using the driver-core driver_override infrastructure taking
care of proper locking internally.
Note that calling match() from __driver_attach() without the device lock
held is intentional. [1]
When a driver is probed through __driver_attach(), the bus' match()
callback is called without the device lock held, thus accessing the
driver_override field without a lock, which can cause a UAF.
Fix this by using the driver-core driver_override infrastructure taking
care of proper locking internally.
Note that calling match() from __driver_attach() without the device lock
held is intentional. [1]
When a driver is probed through __driver_attach(), the bus' match()
callback is called without the device lock held, thus accessing the
driver_override field without a lock, which can cause a UAF.
Fix this by using the driver-core driver_override infrastructure taking
care of proper locking internally.
Note that calling match() from __driver_attach() without the device lock
held is intentional. [1]
Henri A [Wed, 20 May 2026 14:25:44 +0000 (10:25 -0400)]
media: rc: igorplugusb: fix control request setup packet
Commit eac69475b01f ("media: rc: igorplugusb: heed coherency
rules") changed the control request storage from an embedded struct to
an allocated pointer so it can obey DMA coherency rules.
However, the driver still passes &ir->request to usb_fill_control_urb().
That points the URB setup packet at the pointer field itself rather than
at the allocated struct usb_ctrlrequest.
USB core then interprets pointer bytes as the setup packet. This can
produce an invalid bRequestType and trigger the control direction warning
reported by syzbot:
usb 2-1: BOGUS control dir, pipe 80003580 doesn't match bRequestType 0
Pass ir->request itself as the setup packet.
Fixes: eac69475b01f ("media: rc: igorplugusb: heed coherency rules") Reported-by: syzbot+11f0e4f957c7c3bf3d51@syzkaller.appspotmail.com Closes: https://syzkaller.appspot.com/bug?extid=11f0e4f957c7c3bf3d51 Tested-by: syzbot+11f0e4f957c7c3bf3d51@syzkaller.appspotmail.com Cc: stable@vger.kernel.org Assisted-by: Codex:GPT-5.5 Signed-off-by: Henri A <contact@henrialfonso.com> Signed-off-by: Sean Young <sean@mess.org> Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Linus Torvalds [Sat, 30 May 2026 15:37:45 +0000 (08:37 -0700)]
Merge tag 'usb-7.1-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB and Thunderbolt fixes from Greg KH:
"Here is a set of USB fixes and new device ids for 7.1-rc6. Nothing
major in here, just lots of tiny fixes for reported issues found by
users and some older patches found by some scanning tools. Included in
here are:
- typec fixes found by fuzzers that have decided to finally look at
that device interaction path (i.e. before a driver is bound to a
device)
- typec fixes for issues found by users
- thunderbolt driver fixes for reported problems
- cdns3 driver fixes
- dwc3 driver fixes
- new device quirks added
- usb serial driver fixes for broken devices
- other small driver fixes
All of these have been in linux-next for over a week with no reported
issues"
* tag 'usb-7.1-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (54 commits)
USB: serial: cypress_m8: validate interrupt packet headers
USB: serial: safe_serial: fix memory corruption with small endpoint
USB: serial: omninet: fix memory corruption with small endpoint
USB: serial: mxuport: fix memory corruption with small endpoint
USB: serial: cypress_m8: fix memory corruption with small endpoint
USB: cdc-acm: Fix bit overlap and move quirk definitions to header
usb: dwc2: Fix use after free in debug code
usb: chipidea: core: convert ci_role_switch to local variable
usb: gadget: f_fs: serialize DMABUF cancel against request completion
usb: gadget: f_fs: copy only received bytes on short ep0 read
usb: gadget: dummy_hcd: Reject hub port requests for non-existent ports
dt-bindings: usb: Fix EIC7700 USB reset's issue
usbip: vudc: Fix use after free bug in vudc_remove due to race condition
dt-bindings: usb: ti,omap4-musb: Drop duplicate 'usb-phy' property constraints
usb: storage: Add quirks for PNY Elite Portable SSD
USB: quirks: add NO_LPM for Lenovo ThinkPad USB-C Dock Gen2 hub controllers
usb: usbtmc: reject interrupt endpoints with small wMaxPacketSize
usb: usbtmc: check URB actual_length for interrupt-IN notifications
xhci: tegra: Fix ghost USB device on dual-role port unplug
usb: gadget: uvc: hold opts->lock across XU walks in uvc_function_bind
...
Linus Torvalds [Sat, 30 May 2026 15:34:03 +0000 (08:34 -0700)]
Merge tag 'tty-7.1-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver fixes from Greg KH:
"Here are some small serial driver fixes for 7.1-rc6. Included in here
are:
- mips serial driver fixes to resolve some long-standing issues with
how they interacted with the console. That's the "majority" of the
changes in this merge request
- sh-sci driver regression fix
- 8250 driver regression fixes
- other small serial driver fixes for reported problems.
All of these have been in linux-next for over a week with no reported
issues"
* tag 'tty-7.1-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
serial: dz: Enable modular build
serial: zs: Convert to use a platform device
serial: dz: Convert to use a platform device
serial: zs: Switch to using channel reset
serial: zs: Fix bootconsole handover lockup
serial: dz: Fix bootconsole handover lockup
serial: dz: Fix bootconsole message clobbering at chip reset
serial: 8250_dw: dispatch SysRq character in dw8250_handle_irq()
serial: 8250: dispatch SysRq character in serial8250_handle_irq()
serial: core: introduce guard(uart_port_lock_check_sysrq_irqsave)
tty: serial: samsung: Remove redundant port lock acquisition in rx helpers
serial: altera_jtaguart: handle uart_add_one_port() failures
serial: qcom_geni: fix kfifo underflow when flush precedes DMA completion IRQ
serial: fsl_lpuart: fix rx buffer and DMA map leaks in start_rx_dma
tty: add missing tty_driver include to tty_port.h
serial: qcom-geni: fix UART_RX_PAR_EN bit position
serial: sh-sci: fix memory region release in error path
tty: serial: pch_uart: add check for dma_alloc_coherent()
serial: zs: Fix swapped RI/DSR modem line transition counting
Alexis Bouzigues [Fri, 29 May 2026 14:28:14 +0000 (09:28 -0500)]
i2c: virtio: mark device ready before registering the adapter
virtio_i2c_probe() synchronously probes child i2c drivers on the bus,
but peripherals may use the bus at probe for tasks like reading a chip
id. The vhost-user-i2c backend stalls at such probes unless DRIVER_OK
is already set before the virtqueue is first kicked.
Set DRIVER_OK explicitly before i2c_add_adapter(), as done for the
same reason in commit f5866db64f34 ("virtio_console: enable VQs
early") and commit 71e4b8bf0482 ("virtio_rpmsg: set DRIVER_OK before
using device").
Signed-off-by: Alexis Bouzigues <BouziguesAlexis@JohnDeere.com> Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
tracing/probes: Point the error offset correctly for eprobe argument error
Fix to point the error offset correctly for eprobe argument error.
In the cleanup commit 1b8b0cd754cd ("tracing/probes: Move event parameter
fetching code to common parser"), due to incorrect backward compatibility
aimed at conforming to the test specifications, the error location was set
to 0 when a non-existent formal parameter was specified for Eprobe.
However, this should be corrected in both the test and the implementation
to point correct error position.
Miguel Ojeda [Sat, 30 May 2026 11:49:25 +0000 (13:49 +0200)]
rust: x86: support Rust >= 1.98.0 target spec
Starting with Rust 1.98.0 (expected 2026-08-20), the target spec will not
support `x86-softfloat` anymore [1]. Instead, `softfloat` should be used,
which is an alias. Otherwise, one gets:
error: error loading target specification: rustc-abi: invalid rustc abi: 'x86-softfloat'. allowed values: 'x86-sse2', 'softfloat' at line 3 column 32
|
= help: run `rustc --print target-list` for a list of built-in targets
Thus conditionally use one or the other depending on the version.
The alias has existed since Rust 1.95.0 (released 2026-04-16) [2], but
use the newer version instead to avoid changing how the build works for
existing compilers, at least until more testing takes place.
In various code paths, page_table_check_pte_clear() is called
before converting a secure page, while in others it is called
after. Make this consistent and always perform the conversion
after the PTC hook has been called. Also make all conversion‑
eligibility condition checks look the same, and rework the one
in ptep_get_and_clear_full() slightly.
Acked-by: Claudio Imbrenda <imbrenda@linux.ibm.com> Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
In particular, the address of a label is only expected to be used with a
computed goto.
While the generic version more or less works today, it is known to be
brittle and may break with current and future optimizations. For
example, Clang -O2 always returns 1 when this function is inlined:
Fix it by overriding _THIS_IP_ in <asm/linkage.h> (which is included by
<linux/instruction_pointer.h>) using an architecture-specific inline asm
version. Additionally, avoiding taking the address of a label prevents
compilers from emitting spurious indirect branch targets (e.g. ENDBR or
BTI) under control-flow integrity schemes.
Alice Ryhl [Wed, 27 May 2026 18:18:07 +0000 (18:18 +0000)]
rust: arm64: set uwtable llvm module flag for CONFIG_UNWIND_TABLES
Due to a rustc bug [1] the -Cforce-unwind-tables=y flag only emits the
uwtable annotation for functions, but not for the module. This means
that compiler-generated functions such as 'asan.module_ctor' do not
receive the uwtable annotation.
When CONFIG_UNWIND_PATCH_PAC_INTO_SCS is enabled, this leads to boot
failures because the dwarf information emitted for the kasan
constructors is wrong, which causes the SCS boot patching code to
patch the constructor in an illegal manner. Specifically, the paciasp
instruction is patched, but the autiasp instruction is not. This
mismatch leads to a crash when the constructor is called during boot.
==================================================================
BUG: KASAN: global-out-of-bounds in do_basic_setup+0x4c/0x90
Read of size 8 at addr ffffffe3cc7eb488 by task swapper/0/1
Specifically the faulting instruction is the (*fn)() to invoke the
constructor in do_ctors() of the init/main.c file.
Once the fix lands in rustc, this flag can be made conditional on the
rustc version. Note that passing the flag on a rustc with the fix
present has no effect.
[ The fix [1] has landed for Rust 1.98.0 (expected release on
2026-08-20).
Thus add a version check as discussed.
- Miguel ]
Fixes: d077242d68a3 ("rust: support for shadow call stack sanitizer") Cc: stable@kernel.org Link: https://github.com/rust-lang/rust/pull/156973 Reported-by: Bo Ye <bo.ye@mediatek.com> Debugged-by: Isaac Manjarres <isaacmanjarres@google.com> Debugged-by: Sami Tolvanen <samitolvanen@google.com> Tested-by: Isaac Manjarres <isaacmanjarres@google.com> Signed-off-by: Alice Ryhl <aliceryhl@google.com> Link: https://patch.msgid.link/20260527-uwtable-module-flag-v1-1-caa41342be4b@google.com
[ Adjusted link and comment. - Miguel ] Signed-off-by: Miguel Ojeda <ojeda@kernel.org>
Update a comment to refer to folios instead of pages.
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Carlos Maiolino <cem@kernel.org>
xfs: abort mount if xfs_fs_reserve_ag_blocks fails
xfs_mountfs currently ignores all errors from xfs_fs_reserve_ag_blocks,
which can lead to the mount path continuing on corruption errors.
Fix the check to only ignore -ENOSPC as in other callers, and unwind for
all other errors.
Fixes: 81ed94751b15 ("xfs: fix log intent recovery ENOSPC shutdowns when inactivating inodes") Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: "Darrick J. Wong" <djwong@kernel.org> Signed-off-by: Carlos Maiolino <cem@kernel.org>
xfs: factor rtgroup geom write pointer reporting into a helper
Sticks out a bit better if we add a separate helper for it.
Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Carlos Maiolino <cmaiolino@redhat.com> Reviewed-by: Wilfred Mallawa <wilfred.mallawa@wdc.com> Reviewed-by: Damien Le Moal <dlemoal@kernel.org> Signed-off-by: Carlos Maiolino <cem@kernel.org>
xfs: drop the RTG reference later in xfs_ioc_rtgroup_geometry
Keep the rtgroup reference until after reporting the write pointer, as
that uses it. Right now this is not a major issue as we don't support
shrinking file systems in a way that makes RTGs go away, but let's stick
to the proper reference counting to prepare for that.
Fixes: c6ce65cb17aa ("xfs: add write pointer to xfs_rtgroup_geometry") Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Carlos Maiolino <cmaiolino@redhat.com> Reviewed-by: Wilfred Mallawa <wilfred.mallawa@wdc.com> Reviewed-by: Damien Le Moal <dlemoal@kernel.org> Signed-off-by: Carlos Maiolino <cem@kernel.org>
Yingjie Gao [Wed, 27 May 2026 04:31:34 +0000 (12:31 +0800)]
xfs: fix rtgroup cleanup in CoW fork repair
xrep_cow_find_bad_rt() initializes scrub rtgroup state before the
force-rebuild path calls xrep_cow_mark_file_range(). If that call
fails, the code jumps directly to out_rtg, which skips the scrub
rtgroup cleanup and only drops the local rtgroup reference.
Remove the unnecessary jump so the function falls through to out_sr,
ensuring the realtime cursors, lock state, and sr->rtg reference are
released before returning.
Fixes: fd97fe111208 ("xfs: fix CoW forks for realtime files") Cc: <stable@vger.kernel.org> # v6.14 Signed-off-by: Yingjie Gao <gaoyingjie@uniontech.com> Reviewed-by: "Darrick J. Wong" <djwong@kernel.org> Signed-off-by: Carlos Maiolino <cem@kernel.org>
Yingjie Gao [Wed, 27 May 2026 04:31:33 +0000 (12:31 +0800)]
xfs: fix error returns in CoW fork repair
xrep_cow_find_bad() returns success after the cleanup labels even if
AG setup, btree queries, or bitmap updates failed. This can make
repair continue with an incomplete bad-file-offset bitmap instead of
stopping at the original error.
The force-rebuild path has a related cleanup problem. If
xrep_cow_mark_file_range() fails, the function returns directly and
skips the scrub AG context and perag cleanup.
Let the force-rebuild path fall through to the existing cleanup code
and return the saved error after cleanup.
Fixes: dbbdbd008632 ("xfs: repair problems in CoW forks") Cc: <stable@vger.kernel.org> # v6.8 Signed-off-by: Yingjie Gao <gaoyingjie@uniontech.com> Reviewed-by: "Darrick J. Wong" <djwong@kernel.org> Signed-off-by: Carlos Maiolino <cem@kernel.org>
Dai Ngo [Wed, 20 May 2026 00:32:59 +0000 (17:32 -0700)]
xfs: fix overlapping extents returned for pNFS LAYOUTGET
xfs_fs_map_blocks() currently passes XFS_BMAPI_ENTIRE to xfs_bmapi_read(),
which causes the bmap code to expand the mapping to cover the entire
extent rather than the requested range.
A single LAYOUTGET request from the client can cause the server to
issue multiple calls to xfs_fs_map_blocks() for different offsets
within the same extent. Because the use of XFS_BMAPI_ENTIRE flag,
these calls can produce overlapping mappings.
As a result, the LAYOUTGET reply sent to the NFS client may contain
overlapping extents. This creates ambiguity in extent selection for a
given file range, which can lead to incorrect device selection,
inconsistent handling of datastate, and ultimately data corruption or
protocol violations on the client side.
Problem discovered with xfstest generic/075 test using NFSv4.2 mount
with SCSI layout.
Fix this by replacing the XFS_BMAPI_ENTIRE flag with '0' so that
xfs_bmapi_read() returns only the mapping for the requested range.
Fixes: cc6c40e09d7b1 ("NFSD/blocklayout: Support multiple extents per LAYOUTGET"). Signed-off-by: Dai Ngo <dai.ngo@oracle.com> Reviewed-by: Carlos Maiolino <cmaiolino@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Carlos Maiolino <cem@kernel.org>
Dai Ngo [Wed, 20 May 2026 00:32:58 +0000 (17:32 -0700)]
xfs: fix use of uninitialized imap in xfs_fs_map_blocks error path
xfs_fs_map_blocks() acquires the data map lock and then calls
xfs_bmapi_read(). If xfs_bmapi_read() fails, the function currently
still falls through to xfs_bmbt_to_iomap(), which consumes an
uninitialized imap record and may return invalid data to the caller.
Fix this by releasing the data map lock and returning immediately when
xfs_bmapi_read() reports an error. This prevents xfs_bmbt_to_iomap()
from being called with an uninitialized xfs_bmbt_irec.
Fixes: 527851124d10f ("xfs: implement pNFS export operations") Signed-off-by: Dai Ngo <dai.ngo@oracle.com> Reviewed-by: Carlos Maiolino <cmaiolino@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Carlos Maiolino <cem@kernel.org>
Hans Holmberg [Mon, 18 May 2026 06:52:24 +0000 (08:52 +0200)]
xfs: handle racing deletions in xfs_zone_gc_iter_irec
Under heavy garbage collection pressure from RocksDB workloads,
filesystem shutdowns can occur in xfs_zone_gc_iter_irec when
xfs_iget() returns -EINVAL for deleted files.
Fix this by handling -EINVAL just like we handle -ENOENT, allowing
zone GC to safely ignore stale mappings.
Fixes: 080d01c41d44 ("xfs: implement zoned garbage collection") Signed-off-by: Hans Holmberg <hans.holmberg@wdc.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Carlos Maiolino <cem@kernel.org>
Linus Torvalds [Sat, 30 May 2026 04:50:56 +0000 (21:50 -0700)]
Merge tag 'v7.1-rc6-ksmbd-server-fixes' of git://git.samba.org/ksmbd
Pull smb server fixes from Steve French:
- security fix for FSCTL_SET_SPARSE
- fix leak in ksmbd_query_inode_status()
- fix OOB read in smb_check_perm_dacl()
* tag 'v7.1-rc6-ksmbd-server-fixes' of git://git.samba.org/ksmbd:
ksmbd: fix FSCTL permission bypass by adding a permission check for FSCTL_SET_SPARSE
ksmbd: release ksmbd_inode ref via ksmbd_inode_put on lookup paths
ksmbd: OOB read regression in smb_check_perm_dacl() ACE-walk loops
Lukas Bulwahn [Tue, 19 May 2026 03:45:50 +0000 (05:45 +0200)]
MAINTAINERS: Drop obsolete FPU EMULATOR section
Commit
823caa173884 ("x86/fpu: Remove the math-emu/ FPU emulation library")
removes the directory arch/x86/math-emu/, but misses to also remove the
MAINTAINERS section FPU EMULATOR.
As Bill Metzenthen is already mentioned in the CREDITS for his contribution
to the FPU emulator, just add the email address in the MAINTAINERS section
to the CREDITS and then drop the obsolete FPU EMULATOR section.
Linus Torvalds [Sat, 30 May 2026 02:08:20 +0000 (19:08 -0700)]
Merge tag 'drm-fixes-2026-05-30' of https://gitlab.freedesktop.org/drm/kernel
Pull drm fixes from Dave Airlie:
"Regular pull, doesn't seem too insane or AI owned, couple of UAF fixes
and another repair for an earlier fix, mostly amdgpu and i915 display
with xe/i915 accel, and misc core/driver fixes.
It might be a bit bigger than usual at this stage, but I'm not seeing
anything too scary here.
dumb-buffer:
- prevent overflows in dumb-buffer creation
dma-buf:
- fix UAF in dma_buf_fd() tracepoint
gem:
- fix for the fix for the fix for the change handle ioctl
i915:
- Fix potential UAF in TTM object purge
- Use polling when irqs are unavailable
- Fix HDR pre-CSC LUT programming loop
- Block DC states on vblank enable when Panel Replay supported
- Use DC_OFF wake reference to block DC6 on vblank enable
* tag 'drm-fixes-2026-05-30' of https://gitlab.freedesktop.org/drm/kernel: (33 commits)
drm/gem: fix race between change_handle and handle_delete
drm: prevent integer overflows in dumb buffer creation helpers
dma-buf: fix UAF in dma_buf_fd() tracepoint
drm/amdgpu: fix calling VM invalidation in amdgpu_hmm_invalidate_gfx
drm/amdgpu: fix amdgpu_hmm_range_get_pages
drm/amdgpu/userq: use array instead of list for userq_vas
drm/amdgpu/userq: move mqd_destroy to later stage to keep core obj valid
drm/amdkfd: fix a vulnerability of integer overflow in kfd debugger
drm/amdgpu/userq: remove amdgpu_userq_create/destroy_object wrapper
drm/amd/pm/si: Disregard vblank time when no displays are connected
drm/amdkfd: Check for pdd drm file first in CRIU restore path
drm/amdgpu: fix potential overflow in fs_info.debugfs_name
drm/amdgpu/userq: make sure queue is valid in the hang_detect_work
drm/amdgpu/userq: reserve root bo without interruption
drm/amdgpu/userq: add amdgpu_bo_unpin when amdgpu_ttm_alloc_gart fails
drm/amdgpu: simplify return value in amdgpu_userq_get_doorbell_index
drm/amdkfd: fix NULL pointer bug in svm_range_set_attr
drm/amd/display: Write REFCLK to 48MHz on DCN21
drm/amdgpu/userq: Fix the mutex_init cleanup for fence_drv_lock
drm/amdgpu/userq: Fix doorbell object cleanup of queue
...
Linus Torvalds [Sat, 30 May 2026 01:07:37 +0000 (18:07 -0700)]
Merge tag 'spi-fix-v7.1-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"One substantive fix here, fixing corruption of the maximum frequency
for spi-mem operations which caused users to remember what should have
been a temporarily modified maximum frequency as the standard going
forward, potentially causing instability when the modification raised
rather than lowered the frequency.
We also have a trivial patch which just documents the correct way to
describe the Qualcomm IPQ5210 SNAND controller in the DT, there are no
code changes"
* tag 'spi-fix-v7.1-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: spi-mem: avoid mutating op template in spi_mem_supports_op()
spi: dt-bindings: spi-qpic-snand: Add ipq5210 compatible
Linus Torvalds [Fri, 29 May 2026 23:39:56 +0000 (16:39 -0700)]
Merge tag 'regmap-fix-v7.1-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap fix from Mark Brown:
"Some other fixing in an API user turned up the fact that we weren't
correctly applying cache only mode to volatile registers in
regmap_update_bits(), causing us to try to access hardware that was
powered off or otherwise not in a state to accept I/O. This fix
returns an error instead, avoiding more serious consequences"
* tag 'regmap-fix-v7.1-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: reject volatile update_bits() in cache-only mode
Linus Torvalds [Fri, 29 May 2026 22:46:40 +0000 (15:46 -0700)]
Merge tag 'net-7.1-rc6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull more networking fixes from Jakub Kicinski:
"Quick follow up, nothing super urgent here. Main reason I'm sending
this out is because the IPsec and Bluetooth PRs did not make it
yesterday. I don't want to have to send you all of this + whatever
comes next week, for rc7. The fixes under "Previous releases -
regressions" are for real user-reported regressions from v7.0.
Previous releases - regressions:
- Revert "ipv6: preserve insertion order for same-scope addresses"
- xfrm: move policy_bydst RCU sync, a fix which added a sync RCU on
netns exit got backported to stable and was causing serious
accumulation of dying netns's for real workloads
- pcs-mtk-lynxi: fix bpi-r3 serdes configuration
Previous releases - always broken:
- usual grab bag of race, locking and leak fixes for Bluetooth
- handful of page handling fixes for IPsec"
* tag 'net-7.1-rc6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (36 commits)
wireguard: send: append trailer after expanding head
Revert "ipv6: preserve insertion order for same-scope addresses"
net: skbuff: fix pskb_carve leaking zcopy pages
ipv6: fix possible infinite loop in fib6_select_path()
ipv6: fix possible infinite loop in rt6_fill_node()
bpf: sockmap: fix tail fragment offset in bpf_msg_push_data
vsock/virtio: bind uarg before filling zerocopy skb
Revert "esp: fix page frag reference leak on skb_to_sgvec failure"
net: pcs: pcs-mtk-lynxi: fix bpi-r3 serdes configuration
sctp: fix race between sctp_wait_for_connect and peeloff
net: mana: Skip redundant detach on already-detached port
net: mana: Add NULL guards in teardown path to prevent panic on attach failure
Bluetooth: hci_sync: Reset device counters in hci_dev_close_sync()
Bluetooth: hci_sync: Set HCI_CMD_DRAIN_WORKQUEUE during device close
Bluetooth: hci_core: Rework hci_dev_do_reset() to use hci_sync functions
Bluetooth: ISO: serialize iso_sock_clear_timer with socket lock
Bluetooth: ISO: fix UAF in iso_recv_frame
Bluetooth: L2CAP: Fix possible crash on l2cap_ecred_conn_rsp
Bluetooth: l2cap: clear chan->ident on ECRED reconfiguration success
Bluetooth: hci_qca: Use 100 ms SSR delay for rampatch and NVM loading
...
Linus Torvalds [Fri, 29 May 2026 22:17:53 +0000 (15:17 -0700)]
Merge tag 'clang-fixes-7.1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/nathan/linux
Pull clang build fix from Nathan Chancellor:
"A small fix to disable -Wattribute-alias for clang in the few places
it is already disabled for GCC, now that tip of tree clang has
implemented -Wattribute-alias as GCC has"
* tag 'clang-fixes-7.1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/nathan/linux:
Disable -Wattribute-alias for clang-23 and newer
Andrei Vagin [Tue, 26 May 2026 20:50:43 +0000 (20:50 +0000)]
Revert "x86/fpu: Refine and simplify the magic number check during signal return"
This reverts
dc8aa31a7ac2 ("x86/fpu: Refine and simplify the magic number check during signal return").
The aforementioned commit broke applications that construct signal frames in
userspace (such as CRIU and gVisor) if the frame's xstate size is smaller than
the kernel's fpstate->user_size.
Furthermore, this introduces a critical issue for checkpoint/restore tools
like CRIU. If a process is checkpointed while inside a signal handler, its
stack contains a signal frame formatted according to the source host's xstate
capabilities.
If that process is later restored on a destination host with larger xstate
capabilities (e.g., a newer CPU with more features enabled, resulting in
a larger fpstate->user_size), the kernel will look for FP_XSTATE_MAGIC2 at the
destination host's larger user_size offset instead of the offset encoded in
the frame's fx_sw->xstate_size.
This causes the magic2 check to fail, forcing sigreturn to silently fall back
to "FX-only" mode. Upon return from the signal handler, the process's extended
state is reset to initial values instead of being restored, leading to silent
data corruption.
The aforementioned commit cited
d877550eaf2d ("x86/fpu: Stop relying on userspace for info to fault in xsave buffer")
as justification to stop relying on userspace for the magic number check.
However, these two changes are fundamentally different. The last one only
changed how much memory the kernel ensures is paged-in before running XRSTOR
to prevent an infinite loop. It did not change the signal frame format or how
the layout is validated.
Reverting this change restores the use of fx_sw->xstate_size for
locating magic2 and restores the necessary sanity checks, ensuring that
the signal frame remains self-describing and portable.
[ bp: Massage commit message. ]
Fixes: dc8aa31a7ac2 ("x86/fpu: Refine and simplify the magic number check during signal return") Signed-off-by: Andrei Vagin <avagin@google.com> Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de> Acked-by: Chang S. Bae <chang.seok.bae@intel.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/all/20260429000623.3356606-1-avagin@google.com
The probe ordering fix in the following patch ensures amd_gpio_probe()
completes before i2c-designware probes AMDI0010:02, allowing the
existing amd_gpio_irq_enable() flow to work correctly. The manual IRQ
restoration added by this patch is therefore no longer needed.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=221494 Signed-off-by: Hardik Prakash <hardikprakash.official@gmail.com> Reviewed-by: Mario Limonciello (AMD) <superm1@kernel.org> Fixes: 3812a9e84265a ("pinctrl-amd: enable IRQ for WACF2200 touchscreen on Lenovo Yoga 7 14AGP11") Signed-off-by: Linus Walleij <linusw@kernel.org>
Arnd Bergmann [Fri, 29 May 2026 21:39:45 +0000 (23:39 +0200)]
Merge tag 'memory-controller-drv-fixes-7.1' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux-mem-ctrl into arm/fixes
Memory controller drivers - fixes for v7.1
Fix probing of Atmel EBI memory controller driver e.g. on at91
sam9x60-curiosity board due to usage of platform_driver_probe() which is
not handling deferred probe. Lack of EBI driver caused dependant NAND
controller to fail to probe, basically failing entire board boot.
* tag 'memory-controller-drv-fixes-7.1' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux-mem-ctrl:
memory: atmel-ebi: Allow deferred probing
Arnd Bergmann [Fri, 29 May 2026 21:37:25 +0000 (23:37 +0200)]
Merge tag 'samsung-drivers-fixes-7.1-2' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into arm/fixes
Samsung SoC driver fixes for v7.1
Fix several concurrency issues present in Samsung ACPM firmware drivers,
used currently only on Google GS101. Tudor with help of Sashiko
identified several missing barriers and incomplete synchronization,
leading to possible transfer data corruption or use after free. Few
other issues related to probe, including missing mailbox cleanup, were
also fixed.
* tag 'samsung-drivers-fixes-7.1-2' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
firmware: samsung: acpm: Fix infinite loop on sequence number exhaustion
firmware: samsung: acpm: Fix missing LKMM barriers in sequence allocator
firmware: samsung: acpm: Fix false timeouts and Use-After-Free in polling
firmware: samsung: acpm: Fix mailbox channel leak on probe error
firmware: samsung: acpm: Fix cross-thread RX length corruption
Zhenghang Xiao [Tue, 26 May 2026 08:53:13 +0000 (16:53 +0800)]
drm/gem: fix race between change_handle and handle_delete
drm_gem_change_handle_ioctl leaves the old handle live in the IDR
during the window between spin_unlock(table_lock) and the final
spin_lock(table_lock). A concurrent drm_gem_handle_delete on the old
handle succeeds in this window, decrements handle_count to 0, and frees
the GEM object while the new handle's IDR entry still references it.
NULL the old handle's IDR entry before dropping table_lock so that any
concurrent GEM_CLOSE on the old handle sees NULL and returns -EINVAL.
Restore the old entry on the prime-bookkeeping error path.
Fixes: 5e28b7b94408 ("drm: Set old handle to NULL before prime swap in change_handle") Signed-off-by: Zhenghang Xiao <kipreyyy@gmail.com> Cc: stable@vger.kernel.org Signed-off-by: Dave Airlie <airlied@redhat.com> Link: https://patch.msgid.link/20260526085313.26791-1-kipreyyy@gmail.com
Gary Guo [Fri, 8 May 2026 15:29:49 +0000 (16:29 +0100)]
rust: pin_init: internal: use `loop {}` to produce never value
In the `init!`/`pin_init!` macros, we rely on a trick that assigns never
(`!`) values to all mentioned fields in never-executed code to let the
compiler check that all fields have been initialized.
Currently we use `::core::panic!()` to produce this value, but before Rust
1.91.0, it creates outlined `panic_cold_explicit` functions which do not
get removed by the optimizer, thus leaving dead code behind in the binary.
This has been fixed by [1], which lands in Rust 1.91.0+, higher than the
kernel minimum version 1.85.0.
This causes ~200 dead `panic_cold_explicit` instances being included in the
binary, with ~90 of them from nova-core's usage of pin-init.
Work around the issue by using `loop {}` which creates the never value
without macro expansion or function call at all. All instances of
`panic_cold_explicit` outside libcore are removed by this change in my
kernel build.
Linus Torvalds [Fri, 29 May 2026 20:47:55 +0000 (13:47 -0700)]
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull kvm fixes from Paolo Bonzini:
"arm64:
- Restore CONFIG_PKVM_DISABLE_STAGE2_ON_PANIC to its former glory by
making sure the config symbol is correctly spelled out in the code
- Don't reset the AArch32 view of the PMU counters to zero when the
guest is writing to them
- Fix an assorted collection of memory leaks in the newly added
tracing code
- Fix the capping of ZCR_EL2 which could be used in an unsanitised
way by an L2 guest
x86:
- Include the kernel's linux/mman.h in KVM selftests to ensure
MADV_COLLAPSE is defined, as older libc versions may not provide
it.
- Include execinfo.h if and only if KVM selftests are building
against glibc, and provide a test_dump_stack() for non-glibc
builds.
- Silence an annoying RCU splat on (even non-KVM-related) panics.
The splat is technically legit, but in practice not an issue. To
have a race, you would need to unload the KVM modules at exactly
the time a panic happens; and speaking of incredibly rare races,
taking the locks risks introducing a deadlock if the module unload
code took the lock on a CPU that has been halted. Which seems
possibly more likely than the RCU grace period issue, so just shut
it up. This code used to be in KVM but is now outside it; but the
x86 maintainers haven't picked it up, so here we are.
- Rate-limit global clock updates once again (but without delayed
work), as KVM was subtly relying on the old rate-limiting for NPT
correction to guard against "update storms" when running without a
master clock on systems with overcommitted CPUs.
- Fix a brown paper bag goof where KVM checked if ERAPS is "dirty"
instead of marking it dirty when emulating INVPCID.
- Flush the TLB when transitioning from xAVIC => x2AVIC to ensure the
CPU TLB doesn't contain AVIC-tagged entries for the APIC base GPA.
- The top 10 commits fix buffer overflow (and potential TOC/TOU)
flaws in the page state change protocol for encrypted VMs. AI
models find it quite easily given it was reported three times, but
aren't as good at writing a comprehensive fix. There's more to
clean up in the area, which will come in 7.2"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (22 commits)
KVM: SEV: Use READ_ONCE() when reading entries/indices from PSC buffer
KVM: SEV: Check PSC request indices against the actual size of the buffer
KVM: SEV: Don't explicitly pass PSC buffer to snp_begin_psc()
KVM: SEV: WARN if KVM attempts to setup scratch area with min_len==0
KVM: SEV: Compute the correct max length of the in-GHCB scratch area
KVM: SEV: Use the size of the PSC header as the minimum size for PSC requests
KVM: SEV: Ignore Port I/O requests of length '0'
KVM: SEV: Reject MMIO requests larger than 8 bytes with GHCB v2+
KVM: SEV: Ignore MMIO requests of length '0'
KVM: SEV: Require in-GHCB scratch area if GHCB v2+ is in use
KVM: arm64: Correctly cap ZCR_EL2 provided by a guest hypervisor
KVM: arm64: Fix memory leak in hyp_trace_unload()
KVM: arm64: Fix rollback in hyp_trace_buffer_share_hyp()
KVM: arm64: Fix meta-page unsharing in pKVM hyp tracing
KVM: arm64: PMU: Preserve AArch32 counter low bits
KVM: SVM: Flush the current TLB when transitioning from xAVIC => x2AVIC
KVM: x86: Fix ERAPS RAP clear on INVPCID single-context invalidation
KVM: arm64: Fix CONFIG_PKVM_DISABLE_STAGE2_ON_PANIC
KVM: selftests: Guard execinfo.h inclusion for non-glibc builds
KVM: x86: Rate-limit global clock updates on vCPU load
...
Rong Xu [Fri, 29 May 2026 18:53:46 +0000 (11:53 -0700)]
kbuild: distributed build support for Clang ThinLTO
Add distributed ThinLTO build support for the Linux kernel.
This new mode offers several advantages: (1) Increased
flexibility in handling user-specified build options.
(2) Improved user-friendliness for developers. (3) Greater
convenience for integrating with objtool and livepatch.
Note that "distributed" in this context refers to a term
that differentiates in-process ThinLTO builds by invoking
backend compilation through the linker, not necessarily
building in distributed environments.
Distributed ThinLTO is enabled via the
`CONFIG_LTO_CLANG_THIN_DIST` Kconfig option. For example:
> make LLVM=1 defconfig
> scripts/config -e LTO_CLANG_THIN_DIST
> make LLVM=1 oldconfig
> make LLVM=1 vmlinux -j <..>
The build flow proceeds in four stages:
1. Perform FE compilation, mirroring the in-process ThinLTO mode.
2. Thin-link the generated IR files and object files.
3. Find all IR files and perform BE compilation, using the flags
stored in the .*.o.cmd files.
4. Link the BE results to generate the final vmlinux.o.
NOTE: This patch currently implements the build for the main kernel
image (vmlinux) only. Kernel module support is planned for a
subsequent patch.
Tested on the following arch: x86, arm64, loongarch, and
riscv.
The earlier implementation details can be found here:
https://discourse.llvm.org/t/rfc-distributed-thinlto-build-for-kernel/85934
Masahiro Yamada [Fri, 29 May 2026 18:53:44 +0000 (11:53 -0700)]
kbuild: move vmlinux.a build rule to scripts/Makefile.vmlinux_a
Move the build rule for vmlinux.a to a separate file in preparation
for supporting distributed builds with Clang ThinLTO.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org> Tested-by: Rong Xu <xur@google.com> Tested-by: Piotr Gorski <piotrgorski@cachyos.org> Tested-by: Nathan Chancellor <nathan@kernel.org> Signed-off-by: Rong Xu <xur@google.com> Link: https://patch.msgid.link/20260529185347.2418373-2-xur@google.com
[nathan: Squash in forward fix from Rong around '--thin' to $(AR)
https://patch.msgid.link/20260529185347.2418373-3-xur@google.com] Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Gary Guo [Wed, 27 May 2026 17:19:57 +0000 (18:19 +0100)]
rust: pin-init: remove `E` from `InitClosure`
Move `E` from type to trait impl block. This greatly shortens the
monomorphized type names. The `__pinned_init` function name is only
slightly shortened as it still encodes the `E` as part of `PinInit<T, E>`
in the symbol.
`T` cannot be moved to trait impl block otherwise it will start to conflict
with the `impl Init<T> for T` as Rust cannot deduce that there're no types
that fulfill `T: FnOnce(*mut T)`.
Gary Guo [Wed, 27 May 2026 17:19:56 +0000 (18:19 +0100)]
rust: pin-init: move `InitClosure` out from `__internal`
The `__internal` module is for exposing internal items publicly to
procedural macros (pin-init-internal). Types that are crate-local only can
just have proper visibility and does not need to be in `__internal`.
The type name of `InitClosure` can often shows up in symbol names, this
reduces the length slightly.
Mirko Adzic [Wed, 27 May 2026 17:19:54 +0000 (18:19 +0100)]
rust: pin-init: internal: suppress `non_snake_case` lint in `[pin_]init!`
Allows `non_snake_case` lint on local variables generated in `[pin_]init!`.
Conceptually the identifiers in `[pin_]init!` just references the field
names, and are not defining them, so the warning should not be generated,
similar to how constructing a struct with non-snake-case field names do no
generate these warnings.
Reported-by: Gary Guo <gary@garyguo.net> Closes: https://github.com/Rust-for-Linux/pin-init/issues/125 Closes: https://lore.kernel.org/rust-for-linux/DGTBJBIVFZ2K.2F1ZEFGY0G7NK@garyguo.net/ Fixes: 42415d163e5d ("rust: pin-init: add references to previously initialized fields") Signed-off-by: Mirko Adzic <adzicmirko97@gmail.com>
[ Reworded commit message - Gary ] Link: https://patch.msgid.link/20260527-pin-init-sync-v1-3-e20335ed2501@garyguo.net Signed-off-by: Gary Guo <gary@garyguo.net>
Mirko Adzic [Wed, 27 May 2026 17:19:53 +0000 (18:19 +0100)]
rust: pin-init: internal: suppress `non_snake_case` lint in `#[pin_data]`
Allows `non_snake_case` lint on struct fields generated by `#[pin_data]`.
Since the same warning will be reported by the compiler on the struct
definition, having extra warnings for the generated code is unnecessary
and confusing.
rust: pin-init: internal: pin_data: filter non-`#[cfg]` attr in generated code
When using a macro with custom attributes in a `#[pin_data]` struct it
can mess up the generated code. The generated code needs nothing more than
the `#[cfg]` attribute, thus strip away all other attributes.
[ Rebased and updated to only include `#[cfg]` instead of both `#[cfg]` and
`#[doc]`; doc is not needed for the generated hidden items. - Gary ]
EDAC: Consistently define pci_device_ids using named initializers
... and PCI device helpers.
The various struct pci_device_id arrays were initialized mostly by one of the
PCI_DEVICE macros and then list expressions. The latter aren't easily readable
if you're not into PCI. Using named initializers is more explicit and thus
easier to parse.
Also use PCI_DEVICE* helper macros to assign .vendor, .device, .subvendor and
.subdevice where appropriate and skip explicit assignments of 0 (which the
compiler takes care of).
The secret plan is to make struct pci_device_id::driver_data an anonymous
union (similar to
wireguard: send: append trailer after expanding head
With how this is currently written, we add the trailer, zero it out, and
then add the header space on. If that header space requires a
reallocation + copy, the zeros in the trailer aren't copied, because the
skb len hasn't actually been yet expanded to cover that. Instead add the
padding at the end of the process rather than at the beginning.
Revert "ipv6: preserve insertion order for same-scope addresses"
Chris Adams reported that preserving insertion order for same-scope
addresses is causing SSH connections to be dropped after stopping a VM
while running NetworkManager.
NetworkManager caches the IPv6 address configuration, when a RA arrives,
it determines the list of addresses to configure and checks if the
addresses are already in the right order in the kernel. If they aren't,
NetworkManager removes and re-adds them to achieve the desired order.
As the order changes, NetworkManager is confused and reconfigures the
addresses on every update. In addition, this would also affect to cloud
tooling that relies on IPv6 addresses order to identify primary and
secondaries addresses.
1) xfrm: route MIGRATE notifications to caller's netns
Thread the caller's netns through km_migrate() so that
MIGRATE notifications go to the issuing netns, fixing both the
init_net listener leak and MOBIKE notifications inside
non-init netns. From Maoyi Xie.
2) xfrm: ipcomp: Free destination pages on acomp errors
Move the out_free_req label up so that allocated destination
pages are released on decompression errors, not only on success.
From Herbert Xu.
3) xfrm: Check for underflow in xfrm_state_mtu
Reject configurations that cause xfrm_state_mtu() to underflow,
preventing a negative TFCPAD value from becoming a memset size
that triggers an out-of-bounds write of several terabytes.
From David Ahern.
4) xfrm: ah: use skb_to_full_sk in async output callbacks
Convert the possibly-incomplete skb->sk to a full socket pointer
in async AH callbacks so that a request_sock or timewait_sock
never reaches xfrm_output_resume() downstream consumers.
From Michael Bommarito.
5) Add and revert: esp: fix page frag reference leak on skb_to_sgvec failure
The patch does not fix te issue completely.
6) xfrm: esp: restore combined single-frag length gate
Check the aligned post-trailer combined length against a page limit
in the fast path, preventing skb_page_frag_refill() from falling
back to a page too small for the destination scatterlist.
From Jingguo Tan.
7) xfrm: iptfs: reset runtime state when cloning SAs
Reinitialise the clone's mode_data runtime objects before
publishing it, preventing queued skbs from being freed with
list state copied from the original SA when migration fails.
From Shaomin Chen.
8) xfrm: move policy_bydst RCU sync from per-netns .exit to .pre_exit
Flush policy tables and drain the workqueue in a .pre_exit handler
so that cleanup_net() pays one RCU grace period per batch instead
of one per namespace, fixing stalls at high CLONE_NEWNET rates.
From Usama Arif.
9) xfrm: input: hold netns during deferred transport reinjection
Take a netns reference when queueing deferred transport reinjection
work and drop it after the callback completes, keeping the skb->cb
net pointer valid until the deferred work runs.
From Zhengchuan Liang.
* tag 'ipsec-2026-05-29' of git://git.kernel.org/pub/scm/linux/kernel/git/klassert/ipsec:
Revert "esp: fix page frag reference leak on skb_to_sgvec failure"
xfrm: input: hold netns during deferred transport reinjection
xfrm: move policy_bydst RCU sync from per-netns .exit to .pre_exit
xfrm: iptfs: reset runtime state when cloning SAs
xfrm: esp: restore combined single-frag length gate
esp: fix page frag reference leak on skb_to_sgvec failure
xfrm: ah: use skb_to_full_sk in async output callbacks
xfrm: Check for underflow in xfrm_state_mtu
xfrm: ipcomp: Free destination pages on acomp errors
xfrm: route MIGRATE notifications to caller's netns
====================
Pavel Begunkov [Thu, 28 May 2026 18:43:53 +0000 (19:43 +0100)]
net: skbuff: fix pskb_carve leaking zcopy pages
When SKBFL_MANAGED_FRAG_REFS is set, frag pages are not refcounted but
their lifetime is controlled by the attached ubuf_info. To make a copy
of the skb_shared_info, we either should clear the flag and reference
the frags, or keep the flag and have frags unreferenced.
pskb_carve_inside_header() and pskb_carve_inside_nonlinear() don't
follow the rule and thus can leak page references. Let's clear
SKBFL_MANAGED_FRAG_REFS from the original skb to fix it. It's the
simplest way to address it, but there are more performant ways to do
that if it ever becomes a problem.
Jiayuan Chen [Wed, 27 May 2026 05:31:31 +0000 (13:31 +0800)]
ipv6: fix possible infinite loop in fib6_select_path()
Found while auditing the same pattern Sashiko reported in
rt6_fill_node() [1]. Apply the same fix as
commit f8d8ce1b515a ("ipv6: fix possible infinite loop in fib6_info_uses_dev()").
Writers holding tb6_lock can list_del_rcu(&first->fib6_siblings)
without waiting for RCU readers; first->fib6_siblings.next then
still points into the old ring and this softirq-side walker never
reaches &first->fib6_siblings as its terminator. fib6_purge_rt()
always WRITE_ONCE()s first->fib6_nsiblings to 0 before
list_del_rcu(), so an inside-loop check is a reliable detach signal.
Fixes: d9ccb18f83ea ("ipv6: Fix soft lockups in fib6_select_path under high next hop churn") Signed-off-by: Jiayuan Chen <jiayuan.chen@linux.dev> Reviewed-by: Ido Schimmel <idosch@nvidia.com> Link: https://patch.msgid.link/20260527053133.180695-2-jiayuan.chen@linux.dev Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jiayuan Chen [Wed, 27 May 2026 05:31:30 +0000 (13:31 +0800)]
ipv6: fix possible infinite loop in rt6_fill_node()
Sashiko reported this issue [1]. Apply the same fix as
commit f8d8ce1b515a ("ipv6: fix possible infinite loop in fib6_info_uses_dev()").
Writers holding tb6_lock can list_del_rcu(&rt->fib6_siblings)
without waiting for RCU readers; rt->fib6_siblings.next then still
points into the old ring and this softirq-side walker never reaches
&rt->fib6_siblings, causing a CPU stall. fib6_del_route() always
WRITE_ONCE()s rt->fib6_nsiblings to 0 before list_del_rcu(), so an
inside-loop check is a reliable detach signal.
Fixes: d9ccb18f83ea ("ipv6: Fix soft lockups in fib6_select_path under high next hop churn") Signed-off-by: Jiayuan Chen <jiayuan.chen@linux.dev> Reviewed-by: Ido Schimmel <idosch@nvidia.com> Link: https://patch.msgid.link/20260527053133.180695-1-jiayuan.chen@linux.dev Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Yuqi Xu [Wed, 27 May 2026 03:48:15 +0000 (11:48 +0800)]
bpf: sockmap: fix tail fragment offset in bpf_msg_push_data
When bpf_msg_push_data() inserts data in the middle of a scatterlist
entry, it splits the original entry into a left fragment and a right
fragment.
The right fragment offset is page-local, but the code advances it with
`start`, which is the message-global insertion point. For inserts into a
non-first SG entry, this over-advances the offset and leaves the split
layout inconsistent.
Advance the right fragment offset by the fragment-local delta,
`start - offset`, which matches the length removed from the front of the
original entry.
Fixes: 6fff607e2f14 ("bpf: sk_msg program helper bpf_msg_push_data") Cc: stable@kernel.org Reported-by: Yuan Tan <yuantan098@gmail.com> Reported-by: Zhengchuan Liang <zcliangcn@gmail.com> Reported-by: Xin Liu <bird@lzu.edu.cn> Signed-off-by: Yuqi Xu <xuyq21@lenovo.com> Signed-off-by: Ren Wei <n05ec@lzu.edu.cn> Link: https://patch.msgid.link/8b129d10566aa3eb43f61a8f9757bcf51707d324.1779636774.git.xuyq21@lenovo.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jingguo Tan [Wed, 27 May 2026 02:33:01 +0000 (10:33 +0800)]
vsock/virtio: bind uarg before filling zerocopy skb
virtio_transport_send_pkt_info() allocates or reuses the zerocopy uarg
before entering the send loop, but virtio_transport_alloc_skb() still
fills the skb before it inherits that uarg. When fixed-buffer vectored
zerocopy hits MAX_SKB_FRAGS, io_sg_from_iter() may partially attach
managed frags and return -EMSGSIZE. The rollback path call kfree_skb()
to free an skb that carries SKBFL_MANAGED_FRAG_REFS but no uarg, so
skb_release_data() falls through to ordinary frag unref.
Pass the uarg into virtio_transport_alloc_skb() and bind it immediately
before virtio_transport_fill_skb(). This keeps control or no-payload skbs
untouched while ensuring success and rollback share one lifetime rule.
Fixes: 581512a6dc93 ("vsock/virtio: MSG_ZEROCOPY flag support") Signed-off-by: Lin Ma <malin89@huawei.com> Signed-off-by: Rongzhen Cui <cuirongzhen@huawei.com> Signed-off-by: Jingguo Tan <tanjingguo@huawei.com> Acked-by: Arseniy Krasnov <avkrasnov@salutedevices.com> Acked-by: Michael S. Tsirkin <mst@redhat.com> Reviewed-by: Stefano Garzarella <sgarzare@redhat.com> Link: https://patch.msgid.link/20260527023301.1075581-1-malin89@huawei.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
KVM: SEV: Use READ_ONCE() when reading entries/indices from PSC buffer
Use READ_ONCE() when reading entries/indices from the guest-accessible
Page State Change buffer to defend against TOCTOU bugs.
Don't bother with READ_ONCE()/WRITE_ONCE() for cases where KVM is writing
(and not consuming the result!), as the guest isn't supposed to touch the
buffer while it's being processed. I.e. using READ_ONCE() is all about
protecting against misbehaving guests.
Fixes: 9b54e248d264 ("KVM: SEV: Add support to handle Page State Change VMGEXIT") Cc: stable@vger.kernel.org Reviewed-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-ID: <20260501202250.2115252-11-seanjc@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
KVM: SEV: Check PSC request indices against the actual size of the buffer
When processing Page State Change (PSC) requests, validate the PSC buffer
against the effective size of the scratch area, which could be less than
the maximum size if the guest provided a pointer that isn't exactly at the
start of the GHCB shared buffer.
Fixes: 9b54e248d264 ("KVM: SEV: Add support to handle Page State Change VMGEXIT") Cc: stable@vger.kernel.org Reviewed-by: Tom Lendacky <thomas.lendacky@amd.com> Reviewed-by: Michael Roth <michael.roth@amd.com> Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-ID: <20260501202250.2115252-10-seanjc@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
KVM: SEV: Don't explicitly pass PSC buffer to snp_begin_psc()
Stop explicitly passing the PSC buffer to snp_begin_psc(): it *must*
be the scratch area. This will allow fixing a variety of bugs without
further complicating the code.
No functional change intended.
Cc: stable@vger.kernel.org Reviewed-by: Tom Lendacky <thomas.lendacky@amd.com> Reviewed-by: Michael Roth <michael.roth@amd.com> Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-ID: <20260501202250.2115252-9-seanjc@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
KVM: SEV: WARN if KVM attempts to setup scratch area with min_len==0
Now that all paths in KVM properly validate the length needed for the
scratch area, and are guaranteed to pass in a non-zero length, WARN if KVM
attempts to configured the scratch area with min_len==0 to guard against
future bugs.
Cc: stable@vger.kernel.org Reviewed-by: Tom Lendacky <thomas.lendacky@amd.com> Reviewed-by: Michael Roth <michael.roth@amd.com> Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-ID: <20260501202250.2115252-8-seanjc@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
KVM: SEV: Compute the correct max length of the in-GHCB scratch area
When setting the length of the GHCB scratch area, and the area is in the
GHCB shared buffer, set the effective length of the scratch area to the max
possible size given the start of the guest-provided pointer, and the end of
the shared buffer.
The code was "fine" when first introduced, as KVM doesn't consult the
length of the buffer when emulating MMIO, because the passed in @len always
specifies the *max* size required. But for PSC requests, the incoming @len
is just the minimum length (to process the header), and KVM needs to know
the full size of the scratch area to avoid buffer overflows (spoiler alert).
Opportunistically rename @len => @min_len to better reflect its role.
Fixes: 9b54e248d264 ("KVM: SEV: Add support to handle Page State Change VMGEXIT") Cc: stable@vger.kernel.org Reviewed-by: Tom Lendacky <thomas.lendacky@amd.com> Reviewed-by: Michael Roth <michael.roth@amd.com> Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-ID: <20260501202250.2115252-7-seanjc@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
KVM: SEV: Use the size of the PSC header as the minimum size for PSC requests
When handling a Page State Change (PSC) #VMGEXIT use the size of the PSC
header as the minimum size for the scratch area. Per the GHCB spec, PSC
requests do NOT provide the length, i.e. using control->exit_info_2 for the
length is completely made up behavior. The existing code "works", e.g.
even though Linux-as-a-guest always passes '0', because KVM doesn't do
anything with the length when the request is in the GHCB's shared buffer.
Use the header as the min length. Once the header is retrieved, KVM can
use the specified indices to compute the full size of the request.
Fixes: 9b54e248d264 ("KVM: SEV: Add support to handle Page State Change VMGEXIT") Cc: stable@vger.kernel.org Reviewed-by: Tom Lendacky <thomas.lendacky@amd.com> Reviewed-by: Michael Roth <michael.roth@amd.com> Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-ID: <20260501202250.2115252-6-seanjc@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Explicitly ignore Port I/O requests of length '0' (or count '0'), so that
setting up the software scratch area (and other code) doesn't have to
worry about underflowing the length, and to allow for WARNing on trying
to configure the scratch area with len==0.
Fixes: 291bd20d5d88 ("KVM: SVM: Add initial support for a VMGEXIT VMEXIT") Cc: stable@vger.kernel.org Reviewed-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-ID: <20260501202250.2115252-5-seanjc@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Explicitly ignore MMIO requests of length '0', so that setting up the
software scratch area (and other code) doesn't have to worry about
underflowing the length, and to allow for special casing '0' in the
future.
Fixes: 8f423a80d299 ("KVM: SVM: Support MMIO for an SEV-ES guest") Cc: stable@vger.kernel.org Reviewed-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-ID: <20260501202250.2115252-3-seanjc@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Michael Roth [Fri, 1 May 2026 20:22:26 +0000 (13:22 -0700)]
KVM: SEV: Require in-GHCB scratch area if GHCB v2+ is in use
As per the GHCB spec, when using GHCB v2+ require the software scratch area
to reside in the GHCB's shared buffer. Note, things like Page State Change
(PSC) requests _rely_ on this behavior, as the guest can't provide a length
when making the request, i.e. the size of the guest payload is bounded by
the size of the shared buffer.
Failure to force usage of the GHCB, and a slew of other flaws, lets a
malicious SNP guest corrupt host kernel heap memory, and leak host heap
layout information.
setup_vmgexit_scratch() allocates a buffer via kvzalloc(exit_info_2),
where exit_info_2 is guest-controlled. With exit_info_2=24, this yields
a 24-byte allocation in kmalloc-cg-32 (32-byte slab objects). The buffer
holds an 8-byte psc_hdr followed by 8-byte psc_entry structs, so only
entries[0] and entries[1] are in-bounds.
snp_begin_psc() validates end_entry against VMGEXIT_PSC_MAX_COUNT (253)
but NOT against the actual buffer size:
idx_end = hdr->end_entry;
if (idx_end >= VMGEXIT_PSC_MAX_COUNT) { // checks 253, not buffer
snp_complete_psc(svm, ...);
return 1;
}
for (idx = idx_start; idx <= idx_end; idx++) {
entry_start = entries[idx]; // OOB when idx >= 2
The guest sets end_entry=10+, causing the host to iterate entries[2+]
which are OOB into adjacent slab objects. For each OOB entry:
- The host reads 8 bytes (OOB READ / info leak oracle)
- If the data passes PSC validation, __snp_complete_one_psc() writes
cur_page = 1 or 512 into the entry (OOB WRITE, sev.c:3806)
- If validation fails, the error response reveals whether adjacent
memory is zero vs non-zero (information disclosure to guest)
The guest controls allocation size (exit_info_2), entry range
(cur_entry/end_entry), and can fire unlimited VMGEXITs to repeatedly
hit different slab positions.
By exploiting the variety of bugs, a malicious SEV-SNP guest can:
- OOB read adjacent kmalloc-cg-32 objects (heap layout disclosure)
- OOB write cur_page bits into adjacent objects (heap corruption)
- Trigger use-after-free conditions across VMGEXITs
E.g. with KASAN enabled, a single insmod of the PoC guest module
produces 73 KASAN reports:
BUG: KASAN: slab-out-of-bounds in snp_begin_psc+0x126/0x890
Read of size 8 at addr ffff888219ffb5e0 by task qemu-system-x86/2199
BUG: KASAN: slab-out-of-bounds in snp_begin_psc+0x468/0x890
Write of size 8 at addr ffff888351566648 by task qemu-system-x86/2199
The buggy address belongs to the object at ffff888XXXXXXXXX
which belongs to the cache kmalloc-cg-32 of size 32
The buggy address is located N bytes to the right of
allocated 32-byte region [ffff888XXXXXXXXX, ffff888XXXXXXXXX)
Linus Torvalds [Fri, 29 May 2026 17:36:57 +0000 (10:36 -0700)]
Merge tag 'io_uring-7.1-20260529' of git://git.kernel.org/pub/scm/linux/kernel/git/axboe/linux
Pull io_uring fix from Jens Axboe:
"Just a single fix for a regression introduced in this cycle, where
we should ensure the node is visible before the entry is added to
the tctx list"
* tag 'io_uring-7.1-20260529' of git://git.kernel.org/pub/scm/linux/kernel/git/axboe/linux:
io_uring/tctx: set ->io_uring before publishing the tctx node
Paolo Bonzini [Fri, 29 May 2026 17:28:16 +0000 (19:28 +0200)]
Merge tag 'kvm-x86-fixes-7.1-rc6' of https://github.com/kvm-x86/linux into HEAD
KVM x86 fixes for 7.1-rcN
- Include the kernel's linux/mman.h in KVM selftests to ensure MADV_COLLAPSE
is defined, as older libc versions may not provide it.
- Include execinfo.h if and only if KVM selftests are building against glibc,
and provide a test_dump_stack() for non-glibc builds.
- Fudge around an RCU splat in the emegerncy reboot code that is technically
a legitimate flaw, but in practice is a non-issue and fixing the flaw, e.g.
by adding locking, would incur meaningful risk, i.e. do more harm than good.
- Rate-limit global clock updates once again (but without delayed work), as
KVM was subtly relying on the old rate-limiting for NPT correction to guard
against "update storms" when running without a master clock on systems with
overcommitted CPUs.
- Fix a brown paper bag goof where KVM checked if ERAPS is "dirty" instead of
marking it dirty when emulating INVPCID.
- Flush the TLB when transitioning from xAVIC => x2AVIC to ensure the CPU TLB
doesn't contain AVIC-tagged entries for the APIC base GPA.
Linus Torvalds [Fri, 29 May 2026 17:04:09 +0000 (10:04 -0700)]
Merge tag 'cxl-fixes-7.1-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/cxl/cxl
Pull Compute Express Link (CXL) fixes from Dave Jiang:
- cxl/test: update mock dev array before calling platform_device_add()
* tag 'cxl-fixes-7.1-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/cxl/cxl:
cxl/test: Update mock dev array before calling platform_device_add()
* tag 'iommu-fixes-v7.1-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/iommu/linux:
MAINTAINERS: Add my employer to my entries
MAINTAINERS: Add Vasant Hegde to reviewers of AMD IOMMU
iommu, debugobjects: avoid gcc-16.1 section mismatch warnings
iommu/vt-d: Simplify calculate_psi_aligned_address()
Linus Torvalds [Fri, 29 May 2026 15:55:41 +0000 (08:55 -0700)]
Merge tag 'sound-7.1-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"A collection of recent small fixes and quirks.
We still see a bit more changes than wished, but most of them are
device-specific ones that are pretty safe to apply, while a core fix
is a typical UAF fix for PCM core that was recently caught by fuzzer;
so overall nothing looks really worrisome.
Core:
- Fix a UAF in PCM OSS proc interface
HD-audio:
- Fix memory leaks in CS35L56 driver
- Various device-specific quirks for Realtek and CS420x codecs
USB-audio:
- Quirk for TAE1160 USB Audio
- Fix for Scarlett2 Gen4 direct monitor gain
ASoC:
- Fixes for QCom q6asm-dai, Intel bytcht_es8316, and simple-mux codec
FireWire:
- Fix for Motu DSP event queue protection"
* tag 'sound-7.1-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ASoC: codecs: simple-mux: Fix enum control bounds check
ALSA: usb-audio: Add iface reset and delay quirk for TAE1160 USB Audio
ALSA: hda/cs420x: Add CS4208 fixup for iMac16,1
ALSA: hda/realtek: add quirk for HP Dragonfly Folio G3 2-in-1
ALSA: hda/realtek: Fix speaker output on ASUS ROG Strix G615LP
ASoC: qcom: q6asm-dai: use pointer type with kzalloc_obj()
ASoC: qcom: q6asm-dai: remove unnecessary braces
ASoC: qcom: q6asm-dai: fix error handling in prepare and set_params
ASoC: qcom: q6asm-dai: close stream only when running
ASoC: qcom: q6asm-dai: do not set stream state in event and trigger callbacks
ASoC: Intel: bytcht_es8316: Fix MCLK leak on init errors
ALSA: hda/realtek: Limit mic boost on Positivo DN140
ALSA: scarlett2: Fix 2i2 Gen 4 direct monitor gain on firmware 2417
ALSA: pcm: oss: Fix setup list UAF on proc write error
ALSA: hda: cs35l56: Fix system name string leaks
ALSA: hda/realtek: Add HDA_CODEC_QUIRK for Lenovo Yoga Slim 7 14AGP11
ALSA: hda/realtek: Fix incorrect comment for ALC299_FIXUP_PREDATOR_SPK
ALSA: firewire-motu: Protect register DSP event queue positions
Qiuxu Zhuo [Thu, 21 May 2026 12:38:12 +0000 (20:38 +0800)]
EDAC/igen6: Add Intel Nova Lake-H SoC support
Nova Lake-H SoCs share similar memory controller registers and IBECC
(In-Band ECC) registers with Panther Lake-H SoCs but use a new memory
subsystem register for IBECC presence detection.
Add Nova Lake-H SoC compute die IDs and create a new configuration
structure for Nova Lake-H SoCs to enable EDAC support.
Qiuxu Zhuo [Thu, 21 May 2026 12:38:11 +0000 (20:38 +0800)]
EDAC/igen6: Make registers for detecting IBECC configurable
Some Intel CPUs with IBECC (In-Band ECC) capability use different registers
to indicate IBECC presence. Make IBECC detection registers CPU-model
specific and configure them properly for scalable IBECC detection.
Qiuxu Zhuo [Thu, 21 May 2026 07:31:12 +0000 (15:31 +0800)]
EDAC/imh: Add RRL support for Intel Diamond Rapids server
Compared to previous generations, Diamond Rapids RRL (Retry Read error Log)
operates at DDR sub-channel granularity and adds an extra register per set.
It also increases the CORRERRCNT register width from 4 to 8 bytes while
reducing the number of registers from 8 to 4.
Add the Diamond Rapids RRL register configuration table and enable support.
Qiuxu Zhuo [Thu, 21 May 2026 07:31:11 +0000 (15:31 +0800)]
EDAC/{skx_common,i10nm}: Prepare RRL for sub-channel granularity
To prepare for enabling Diamond Rapids server RRL (Retry Read error Log),
which operates at sub-channel granularity by converting struct
res_config::reg_rrl_ddr from a single pointer to an array (reg_rrl_ddr[2])
and updating all users in i10nm_edac and skx_common accordingly.
Initialize only reg_rrl_ddr[0] for existing platforms and prepare for
supporting two RRL set groups per DDR channel (one per sub-channel)
when present.
Qiuxu Zhuo [Thu, 21 May 2026 07:31:10 +0000 (15:31 +0800)]
EDAC/skx_common: Add SubChannel support to ADXL decode
Diamond Rapids server RRL (Retry Read error Log) operates at sub-channel
granularity. Add SubChannel support to ADXL decoding in preparation for
enabling this feature.
Also introduce adxl_component_required() to validate mandatory ADXL
components to improve code readability.
Qiuxu Zhuo [Thu, 21 May 2026 07:31:08 +0000 (15:31 +0800)]
EDAC/{skx_common,i10nm}: Introduce rrl_ctrl_mode
RRL (Retry Read error Log) ownership is currently inferred from
retry_rd_err_log magic values, making control semantics implicit
and harder to understand.
Introduce rrl_ctrl_mode to explicitly describe whether RRL is
controlled by none, BIOS, or Linux, and replace direct checks with
named control states to improve readability and maintainability.
skx_set_decode() currently handles both address decoding and Retry
Read error Log (RRL) reporting, coupling two independent functions
in a single API. This complicates setup/teardown and forces callers
to update unrelated state.
Introduce skx_set_show_rrl() and keep skx_set_decode() focused on
decode setup, allowing decode and RRL handling to be managed
independently.
Also rename the callback type and variable to skx_show_rrl_f and
show_rrl for clearer RRL terminology and consistency.
Qiuxu Zhuo [Thu, 21 May 2026 07:31:05 +0000 (15:31 +0800)]
EDAC/{skx_common,i10nm,imh}: Move MC register access helpers to skx_common
Both i10nm_basic.c and imh_basic.c use identical helpers for accessing
memory controller MMIO-based registers. Move these helpers to skx_common.c
to eliminate code duplication. This change also prepares for an upcoming
patch that will move RRL(retry_rd_err_log) code from i10nm_basic.c to
skx_common.c, which requires these helpers to be available in skx_common.c.
Additionally, prefix these function names with 'skx_' to maintain naming
consistency within the file.
EDAC/igen6: Fix memory topology parsing for Panther Lake-H SoCs
Panther Lake-H SoC memory controller registers for memory topology have
been updated, but the current igen6_edac driver still uses old generation
ones to incorrectly parse memory topology.
Fix the issue by adding memory topology parsing function pointers to the
'struct res_config' and creating a new configuration structure for Panther
Lake-H SoCs to enable igen6_edac to parse memory correctly.
EDAC/igen6: Fix call trace due to missing release()
When unloading the igen6_edac driver, there is a call trace:
Device '(null)' does not have a release() function, it is broken and must be fixed.
See Documentation/core-api/kobject.rst.
WARNING: drivers/base/core.c:2567 at device_release+0x84/0x90, CPU#5: rmmod/127209
...
RIP: 0010:device_release+0x84/0x90
Call Trace:
<TASK>
kobject_put+0x8c/0x220
put_device+0x17/0x30
igen6_unregister_mcis+0xa2/0xe0 [igen6_edac]
igen6_remove+0x82/0xb0 [igen6_edac]
...
Fix the call trace by providing empty release() functions for the
memory controller devices.
Thorsten Blum [Fri, 8 May 2026 14:38:46 +0000 (16:38 +0200)]
EDAC/sb_edac: fix grammar in sb_decode_ddr3 warning
Fix the warning in sb_decode_ddr3() by adding the missing verb "is" and
using "supported" instead of "support" to match the LockStep warning in
sb_decode_ddr4().
EDAC/i5400: disable error reporting at teardown and refactor helper
If error reporting is enabled during initialization but initialization
fails immediately after, or during normal driver teardown, error reporting
is left enabled in the mask register even after exit.
Replace i5400_enable_error_reporting() with i5400_set_error_reporting()
to combine enabling/disabling. Disable reporting at initialization
failure and driver exit, before call to i5400_put_devices() for cleanup.
This ensures clean hardware handling by disabling any unused error
reporting bits before exiting.
EDAC/i5100: disable error reporting at teardown and create helper
Error reporting is enabled during init but not reverted when init fails.
It is also not disabled at normal driver teardown.
Create i5100_set_error_reporting() to enable/disable reporting. Move
enable reporting write to after initialization success. Disable reporting
at driver teardown.
EDAC/i5000: disable error reporting at teardown and refactor helper
If error reporting is enabled during initialization but initialization
fails immediately after, or during normal driver teardown, error reporting
is left enabled in the mask register even after exit.
Replace i5000_enable_error_reporting() with i5000_set_error_reporting()
to combine enabling/disabling. Disable reporting at initialization
failure and driver exit, before call to i5000_put_devices() for cleanup.
This ensures clean hardware handling by disabling any unused error
reporting bits before exiting.
projects / thirdparty / linux.git / log
