Primoz Fiser [Tue, 17 Mar 2026 12:31:26 +0000 (13:31 +0100)]
board: phytec: phycore-imx91-93: Add phyCORE-i.MX91 support
As the PHYTEC phyCORE-i.MX91 [1] is just another variant of the existing
PHYTEC phyCORE-i.MX93 SoM but with i.MX91 SoC populated instead, add it
to the existing board-code "phycore_imx93", and rename that board to
"phycore_imx91_93" to reflect the dual SoCs support. While at it, also
rename and change common files accordingly. This way i.MX91 and i.MX93
SoC variants of the phyCORE SoM share most of the code and documentation
without duplication, while maintaining own device-tree and defconfigs
for each CPU variant.
pci: imx: Properly support upstream Linux reset-gpios property
The driver requests explicitly "reset-gpio" property, not the one with
"gpios" suffix but upstream Linux kernel deprecated it in 2021.
Existing upstream Linux kernel DTS is being changed to "reset-gpios"
property, thus update the driver to read that one too.
Note that driver is probably broken already, because it parsed GPIO in
standard way respecting the flags and on top of that applied the
"reset-gpio-active-high" flag, thus "reset-gpio ACTIVE_LOW" with the
"reset-gpio-active-high" property would be double inverted.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
net:
- airoha_eth & pcs_airoha driver fixes
- Rework some symbol dependencies
- dwc_eth_xgmac: Move DMA reset and pad calibration after PHY init
- rtl8169: add support for RTL8125d
- rswitch: Avoid NULL pointer dereference during PHY access
- rswitch: Remap CPU to bus addresses using dev_phys_to_bus()
- phy: dp83867: reset PHY on init to ensure clean state
net-lwip:
- nfs: fix buffer overflow when using symlinks
- tftp: update image_load_addr after successful transfer
[trini: Add missing "if NET" to CMD_DHCP select's CMD_BOOTP] Signed-off-by: Tom Rini <trini@konsulko.com>
Marek Vasut [Wed, 25 Mar 2026 01:10:43 +0000 (02:10 +0100)]
net: rswitch: Remap CPU to bus addresses using dev_phys_to_bus()
Use dev_phys_to_bus() to convert CPU addresses of DMA descriptors
into bus addresses of DMA descriptors. This is necessary on hardware
which does not have 1:1 mapping between CPU and memory addressed by
the DMA. This has no impact on other hardware which does not need
this conversion.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Pranav Tilak [Wed, 25 Mar 2026 15:36:34 +0000 (16:36 +0100)]
net: phy: dp83867: reset PHY on init to ensure clean state
After a warm reboot, the PHY is left in power-down state
(BMCR_PDOWN set) causing auto-negotiation to timeout when
running the dhcp command.
Fix this by calling phy_reset() in dp83867_config() which
brings the PHY to a known clean state. The existing
DP83867_SW_RESTART is removed as it is redundant after phy_reset().
Fixes: 721aed79126b ("net: phy: Add support for Texas Instruments DP83867") Signed-off-by: Pranav Tilak <pranav.vinaytilak@amd.com> Signed-off-by: Michal Simek <michal.simek@amd.com>
Pranav Sanwal [Thu, 26 Mar 2026 10:41:58 +0000 (16:11 +0530)]
net: lwip: tftp: update image_load_addr after successful transfer
do_tftpb() parses the load address into a local variable laddr but
never updates the global image_load_addr. Commands that rely on
image_load_addr as their default address (e.g. 'bmp info')
therefore operate on the wrong address when called without
an explicit argument after tftpboot.
Update image_load_addr to laddr only on a successful transfer, so
that it accurately reflects where data was actually loaded.
Fixes: 4d4d7838127e ("net: lwip: add TFTP support and tftpboot command") Signed-off-by: Pranav Sanwal <pranav.sanwal@amd.com> Reviewed-by: Jerome Forissier <jerome.forissier@arm.com>
Marek Vasut [Wed, 25 Mar 2026 01:09:05 +0000 (02:09 +0100)]
net: rswitch: Avoid NULL pointer dereference during PHY access
At the very early stage when PHY ID is being auto-detected, the
PHY device is not yet instantiated and rswitch_etha .phydev is
still NULL. Add missing check for this condition and perform C22
fallback access in this PHY ID auto-detection case.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Tom Rini [Mon, 23 Mar 2026 19:53:00 +0000 (13:53 -0600)]
net: Correct dependencies for HIFEMAC_ETH
The HIFEMAC_ETH functionality can only work with both DM_ETH_PHY and
DM_MDIO enabled (it calls one of the functions that requires both), so
express this dependency in Kconfig.
Tom Rini [Mon, 23 Mar 2026 19:52:53 +0000 (13:52 -0600)]
net: cmd: Correct dependencies for CMD_PXE
The CMD_PXE functionality can only build with CMD_TFTPBOOT enabled (or
we get undefined references to do_tftpb), so express this dependency in
Kconfig.
Pranav Tilak [Mon, 23 Mar 2026 09:44:14 +0000 (15:14 +0530)]
net: lwip: nfs: fix buffer overflow when using symlinks
When resolving a symlink, nfs_path points into a heap allocated buffer
which is just large enough to hold the original path with no extra
space. If the symlink target name is longer than the original
filename, the write goes beyond the end of the buffer corrupting
heap memory.
Fix this by ensuring nfs_path always points to a buffer large enough
to accommodate the resolved symlink path.
Fixes: 230cf3bc2776 ("net: lwip: nfs: Port the NFS code to work with lwIP") Signed-off-by: Pranav Tilak <pranav.vinaytilak@amd.com> Acked-by: Jerome Forissier <jerome.forissier@arm.com> Reviewed-by: Jerome Forissier <jerome.forissier@arm.com>
Tom Rini [Fri, 20 Mar 2026 20:53:27 +0000 (14:53 -0600)]
net: Rework dependencies around NET/NET_LWIP and NETDEVICES
Functionally, both networking stacks require DM_ETH. This is because
they both also require some networking devices to be enabled. Express
this more correctly by having both NET and NET_LWIP select NETDEVICES.
In turn NETDEVICES no longer depends on NET or NET_LWIP as it's not
prompted anymore.
Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Jerome Forissier <jerome.forissier@arm.com>
Boon Khai Ng [Thu, 12 Mar 2026 11:22:47 +0000 (19:22 +0800)]
phy: micrel: ksz90x1: Issue PHY soft reset during configuration
- Add a call to phy_reset() in ksz9031_config() to ensure the PHY is
properly reset during initialization.
- This clears the power-down bit and ensures the PHY recovers correctly
after Linux reboot.
Tested on Agilex5 hardware with KSZ90X1 PHY.
Signed-off-by: Boon Khai Ng <boon.khai.ng@altera.com>
Boon Khai Ng [Thu, 12 Mar 2026 11:22:46 +0000 (19:22 +0800)]
net: dwc_eth_xgmac: Move DMA reset and pad calibration after PHY init
- Move DMA software reset and pad calibration in xgmac_start() to occur
after the PHY is initialized and connected.
- This ensures the PHY is ready before performing these operations,
which is necessary for proper recovery after reboot.
This change fixes issues where the PHY did not recover from power-down
state after a Linux reboot, for the board using Micrel KSZ90x1 PHY.
Signed-off-by: Boon Khai Ng <boon.khai.ng@altera.com>
Tom Rini [Tue, 17 Mar 2026 01:24:23 +0000 (19:24 -0600)]
net: Rework some symbol dependencies
As exposed by "make randconfig", we have a few dependency issues with
some network drivers:
- Both HIFEMAC_ETH and HIGMACV300_ETH functionally require both DM and
OF_CONTROL. Further, HIFEMAC_ETH needs DM_CLK not just CLK to be
selected.
- BNXT_ETH deals with it's PCI requirement in a backwards way. The
symbol PCI_INIT_R is board specific, PCI alone is required to build.
net: airoha: probe airoha switch mdio on airoha_eth probing
Airoha switch mdio maybe used not only by GDM1, but also by other GDM
ports (ex: as21xxx phy connected to GDM2 port). So it's better probe
airoha switch mdio a bit early in the airoha_eth_probe() code.
Also remove useless eth_phy_set_mdio_bus() call and related code.
Marek Vasut [Tue, 17 Mar 2026 02:17:40 +0000 (03:17 +0100)]
console: Prefer currently selected serial console as stdio device
Adjust the scan for default console stdio device to prefer the
currently selected serial device. This is useful in combination
with CONFIG_SERIAL_PROBE_ALL=y, in which case the system would
instantiate all serial devices as stdio devices in the order in
which they are listed in control DT. The currently selected serial
device may not be the first device listed in DT, in which case the
current console_init_r() implementation unexpectedly switches to
another serial console after listing stderr using "Err:" line, and
just before showing U-Boot shell, which is not the desired behavior.
The scan now iterates over the entire list of stdio devices. If the
current iterator stdio device is the current serial device, or there
is no input or output stdio device assigned to the input or output
stream yet, then the current iterator stdio device is assigned to that
stream. This way, the first suitable stdio device is assigned to the
stream, but the current serial console stdio device can override that
assignment.
As a small optimization, if the current iterator stdio device is the
current serial device and both input and output streams as assigned,
then the loop can terminate, because the current serial device has a
chance to be used as a stdio device at this point.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org> Reviewed-by: Simon Glass <sjg@chromium.org>
Tom Rini [Tue, 17 Mar 2026 01:24:19 +0000 (19:24 -0600)]
core: Rework REGMAP symbols implementation
As exposed by "make randconfig", we have an issue with the dependencies
for REGMAP (and xPL variants). As this is a library function, it should
always be selected and not depended on by other functionality. This is
largely done correctly today, so just correct the few outliers.
Acked-by: Anshul Dalal <anshuld@ti.com> Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Tue, 17 Mar 2026 01:24:16 +0000 (19:24 -0600)]
usb: isp1760: Correct dependencies for USB_ISP1760
As exposed by "make randconfig", we have an issue with the dependencies
for USB_ISP1760. It depends on DM && OF_CONTROL being set and
functionally requires REGMAP. As part of fixing that issue, we change
"tristate" to "bool" and remove mentions of module support as that's not
a thing in U-Boot.
Reviewed-by: Marek Vasut <marek.vasut+usb@mailbox.org> Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Tue, 17 Mar 2026 01:24:54 +0000 (19:24 -0600)]
test: Correct dependencies for SPL_UNIT_TEST
As exposed by "make randconfig", we have an issue with the dependencies
for SPL_UNIT_TEST. In order to test SPL_DM_DEVICE_REMOVE we also need to
have ensured that SPL_DM is enabled, so select that as well.
Tom Rini [Tue, 17 Mar 2026 01:24:44 +0000 (19:24 -0600)]
timer: Correct dependencies for SPL_TIMER
As exposed by "make randconfig", we have an issue with the dependencies
for SPL_TIMER. This depends not just on SPL but also SPL_DM to function,
so add that.
Tom Rini [Tue, 17 Mar 2026 01:24:41 +0000 (19:24 -0600)]
pinctrl: Correct dependencies for PINCTRL_TH1520
As exposed by "make randconfig", we have an issue with the dependencies
for PINCTRL_TH1520. It really needs to depend on PINCTRL_GENERIC rather
than select it, and PINCTRL_GENERIC in turn already depends on
PINCTRL_FULL.
Tom Rini [Tue, 17 Mar 2026 01:24:39 +0000 (19:24 -0600)]
misc: Correct dependencies on QCOM_GENI
As exposed by "make randconfig", we have an issue with the dependencies
for QCOM_GENI. The symbol PARTITION_TYPE_GUID depends on EFI_PARTITION
and this driver cannot function without both being set, so select that
as well.
Reviewed-by: Casey Connolly <casey.connolly@linaro.org> Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Tue, 17 Mar 2026 01:24:37 +0000 (19:24 -0600)]
input: Correct dependencies for BUTTON_KEYBOARD
As exposed by "make randconfig", we have an issue with the dependencies
for BUTTON_KEYBOARD. This needs to also depend on DM_GPIO, and then
select BUTTON as well as BUTTON_GPIO, in order to meet all its
requirements.
Reviewed-by: Casey Connolly <casey.connolly@linaro.org> Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Tue, 17 Mar 2026 01:24:31 +0000 (19:24 -0600)]
SPL: Rework logic around SPL_BLK_FS (and SPL_NVME)
As exposed by "make randconfig", we have an issue around SPL_BLK_FS.
This is functionally a library type symbol that should be selected when
required and select what it needs. Have SPL_BLK_FS select SPL_FS_LOADER
and then SPL_NVME will now correctly select SPL_FS_LOADER via
SPL_BLK_FS.
Tom Rini [Tue, 17 Mar 2026 01:24:29 +0000 (19:24 -0600)]
boot: Update dependencies for some UPL options
As exposed by "make randconfig", we have an issue around SPL_UPL. This
depends on SPL_LIBGENERIC_SUPPORT indirectly. In turn, SPL_UPL_OUT needs
to next depend on SPL_UPL.
Tom Rini [Tue, 17 Mar 2026 01:24:28 +0000 (19:24 -0600)]
boot: Update tests around network symbols in BOOT_DEFAULTS_CMDS
As exposed by "make randconfig", we have an issues around a number of
symbols in BOOT_DEFAULTS_CMDS. Due to the nature of how we currently
handle other networking related command options, we need to be testing
for "!NO_NET" (which is the symbol for no networking stack) or "NET ||
NET_LWIP" rather than CMD_NET alone. For consistency and clarity here
use "CMD_NET && !NO_NET" here.
Tom Rini [Tue, 17 Mar 2026 01:24:24 +0000 (19:24 -0600)]
sysreset: Rework tests around SYSRESET_CMD_POWEROFF
As exposed by "make randconfig", we have an issue around how
SYSRESET_CMD_POWEROFF is typically selected. We cannot rely only on
CMD_POWEROFF as SYSRESET_CMD_POWEROFF must also be tested for its own
dependency of SYSRESET.
Tom Rini [Tue, 17 Mar 2026 01:24:21 +0000 (19:24 -0600)]
xPL FIT: Rework SPL_FIT dependencies
As exposed by "make randconfig", we have xPL_FIT select'ing
xPL_OF_CONTROL, and that in turn requires xPL_LIBGENERIC_SUPPORT. The
most reasonable solution here is to have xPL_FIT select
xPL_LIBGENERIC_SUPPORT.
Introduce new mode of relocation which relocates only data, not code.
This is mainly meant to relocate data to read-write portion of the RAM,
while the code remains in read-only portion of the RAM from which it is
allowed to execute. This split configuration is present on various secure
cores.
The result of the relocation is U-Boot running at its original address,
data relocated to the end of DRAM, but with added read-write area offset.
The U-Boot binary area is not reserved from the end of the DRAM in this
relocation mode, because U-Boot itself is not relocated.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Marek Vasut [Sun, 15 Mar 2026 23:50:33 +0000 (00:50 +0100)]
arm: Introduce current_pl() on ARM32 and compatibility current_el()
The ARM32 has PLx Privilege Levels instead of Exception Levels present
on ARM64. Introduce current_pl() function which reports the current PL
on ARM32.
Introduce current_el() for ARM32 as well and current_pl() for ARM64
which each call the other matching function. This is mainly mean to
allow code like this to compile and retain compile time code coverage:
if (IS_ENABLED(CONFIG_ARM64) && current_el() != 3) { ... }
if (!IS_ENABLED(CONFIG_ARM64) && current_pl() != 0) { ... }
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Padmarao Begari [Sun, 15 Mar 2026 13:15:29 +0000 (18:45 +0530)]
cmd: part: add part dupcheck subcommand
Add a 'part dupcheck' subcommand that scans all block devices probed
in U-Boot and reports any partitions sharing the same PARTUUID or
PARTLABEL. This helps detect situations where the same disk image has
been flashed onto multiple boot devices (e.g., USB stick and UFS),
which can lead to unpredictable boot behavior. Duplicate
PARTUUIDs break UUID-based partition lookup in Linux, and duplicate
PARTLABELs cause the wrong partition to be silently selected in
bootscripts that reference partitions by name.
A single collection pass iterates over all block devices using
blk_foreach_probe() and records every partition that carries a UUID
or label into a dynamically allocated alist of struct part_seen
entries (UUID string, name string, device pointer, partition number).
Duplicates are detected by calling detect_duplicates() twice, once
for UUIDs and once for labels. Each call sorts the list with qsort()
using a comparator that places empty fields at the end, then performs
a single linear pass to identify consecutive equal entries as
duplicate groups. Each group is reported with the device name and
partition number of every copy, followed by a per-field summary
count. Per-field counts are used consistently in both the
duplicate-found and no-duplicates paths.
Example output (with duplicates):
=> part dupcheck
Warning: duplicate PARTUUID 1234abcd-01 (2 copies)
found on usb_mass_storage.lun0:1
found on ufs_scsi.id0lun0:1
Found 1 duplicate PARTUUID(s) (2 total copies) among 4 partitions
Warning: duplicate PARTLABEL primary (2 copies)
found on usb_mass_storage.lun0:1
found on ufs_scsi.id0lun0:1
Found 1 duplicate PARTLABEL(s) (2 total copies) among 4 partitions
Example output (mixed: UUID duplicates, no label duplicates):
=> part dupcheck
Warning: duplicate PARTUUID 1234abcd-01 (2 copies)
found on usb_mass_storage.lun0:1
found on ufs_scsi.id0lun0:1
Found 1 duplicate PARTUUID(s) (2 total copies) among 4 partitions
No duplicate PARTLABELs found (3 labels)
Example output (no duplicates):
=> part dupcheck
No duplicate PARTUUIDs or PARTLABELs found (4 UUIDs, 3 labels)
The CONFIG_CMD_PART_DUPCHECK Kconfig option (depends on
CMD_PART and BLK) controls inclusion of this subcommand and is
disabled by default.
Signed-off-by: John Toomey <john.toomey@amd.com> Signed-off-by: Padmarao Begari <padmarao.begari@amd.com>
Ludwig Nussel [Tue, 10 Mar 2026 15:58:26 +0000 (16:58 +0100)]
Add back debug output of hashed nodes
Commit 2092322b31cc ("boot: Add fit_config_get_hash_list() to build
signed node list") removed printing the list of hashed nodes during
verification. Add it back to have a chance to compare the list when
debugging.
Signed-off-by: Ludwig Nussel <ludwig.nussel@siemens.com>
* TI boards
- fix OP-TEE args
- fix incorrect labels for boot switches
* Fix typo in pstore documentation.
* Fix document references pointing to replaced uImage.FIT.
* buildman: Add missing :: for examples.
* overlay-fdt-boot: .dtbos do not need load addresses.
* When building the documentation use sys.path.append for pytests.
Michal Simek [Tue, 17 Mar 2026 16:26:22 +0000 (17:26 +0100)]
cpu: microblaze: Fix unmet direct dependencies for XILINX_MICROBLAZE0_PVR
As exposed by "make randconfig", CPU_MICROBLAZE uses select to
force-enable XILINX_MICROBLAZE0_PVR, but that symbol depends on
TARGET_MICROBLAZE_GENERIC. The select bypasses this dependency chain,
triggering a Kconfig warning:
WARNING: unmet direct dependencies detected for XILINX_MICROBLAZE0_PVR
Depends on [n]: MICROBLAZE [=y] && TARGET_MICROBLAZE_GENERIC [=n]
Selected by [y]:
- CPU_MICROBLAZE [=y] && CPU [=y] && MICROBLAZE [=y]
Change XILINX_MICROBLAZE0_PVR from select to depends on, so that the
CPU driver is only available when PVR support has been explicitly
enabled.
Anshul Dalal [Fri, 13 Mar 2026 09:41:44 +0000 (15:11 +0530)]
doc: board: ti: fix incorrect labels for boot switches
The labels for the boot mode switches were incorreclty documented for
some TI boards, this patch fixes them as per the official user guides
linked below:
Anshul Dalal [Thu, 12 Mar 2026 09:32:49 +0000 (15:02 +0530)]
doc: board: fix OPTEE args for TI SoCs
CFG_WITH_SOFTWARE_PRNG=y was added as an OPTEE argument to workaround
some bugs related to TRNG which have been fixed now[1]. Therefore this
patch drops the redundant argument from the documentation.
Tom Rini [Mon, 9 Mar 2026 18:09:52 +0000 (12:09 -0600)]
doc: Use sys.path.append for pytests being found
Rather than having our "docs" build tagets modify PTYHONPATH, have
doc/conf.py append the required paths at runtime instead. This will
ensure that our builds from readthedocs will also find all of the
required files.
David Lechner [Fri, 6 Mar 2026 19:52:49 +0000 (13:52 -0600)]
doc/buildman: fix missing :: on examples
Fix 4 instances in buildman.rst where examples were missing :: for
proper formatting. Three cases just had a single : and in one case,
: didn't make grammatical sense, so it gets a stand-alone :: along
with fixing the indent.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Daniel Golle [Fri, 27 Feb 2026 00:03:29 +0000 (00:03 +0000)]
treewide: fix uImage.FIT document paths
Commit 488445cefa1 ("doc: Move FIT into its own directory") moved the
documentation in doc/uImage.FIT to doc/usage/fit, subsequently all
documents and example sources have been converted to reStructuredText.
Fix (almost) all of the remaining occurrences of the old path and
filenames across the tree.
The exception is doc/uImage.FIT/command_syntax_extensions.txt which
apparently has been removed entirely, or at least I was unable to
locate where that document is now.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Tom Rini [Thu, 26 Mar 2026 17:04:41 +0000 (11:04 -0600)]
Merge patch series "Introduce SQUASHFS support in SPL"
Richard Genoud <richard.genoud@bootlin.com> says:
SquashFS has support in U-Boot, but not in SPL.
This series adds the possibility for the SPL to load files from SquashFS
partitions.
This is useful, for instance, when there's a SquashFS rootfs containing
U-Boot binary.
Richard Genoud [Fri, 13 Mar 2026 10:42:29 +0000 (11:42 +0100)]
MAINTAINERS: SQUASHFS: Add myself as co-maintainer
I propose myself to maintain the squashfs files with João.
Also, reorder patterns in alphabetical order.
Signed-off-by: Richard Genoud <richard.genoud@bootlin.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com> Reviewed-by: João Marcos Costa <joaomarcos.costa@bootlin.com>
Richard Genoud [Fri, 13 Mar 2026 10:42:28 +0000 (11:42 +0100)]
MAINTAINERS: SQUASHFS: update João Marcos Costa email
João is using his Bootlin address now.
Signed-off-by: Richard Genoud <richard.genoud@bootlin.com> Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com> Reviewed-by: João Marcos Costa <joaomarcos.costa@bootlin.com>
Richard Genoud [Fri, 13 Mar 2026 10:42:27 +0000 (11:42 +0100)]
spl: mmc: support squashfs
spl_mmc_do_fs_boot supports now loading an image from squashfs.
Also, convert #if defined(CONFIG_SPL_xx) to if (CONFIG_IS_ENABLED(xx))
Signed-off-by: Richard Genoud <richard.genoud@bootlin.com> Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com> Reviewed-by: João Marcos Costa <joaomarcos.costa@bootlin.com>
Richard Genoud [Fri, 13 Mar 2026 10:42:26 +0000 (11:42 +0100)]
spl: add squashfs support
Implement spl_load_image_sqfs() in spl code.
This will be used in MMC to read a file from a squashfs partition.
Also, loosen squashfs read checks on file size by not failing when a
bigger size than the actual file size is requested. (Just read the file)
This is needed for FIT loading, because the length is ALIGNed.
Signed-off-by: Richard Genoud <richard.genoud@bootlin.com> Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com> Reviewed-by: João Marcos Costa <joaomarcos.costa@bootlin.com>
Richard Genoud [Fri, 13 Mar 2026 10:42:25 +0000 (11:42 +0100)]
fs/squashfs: squashfs.h: include file should be self dependent
Otherwise, we get a lot of errors when including this file.
Signed-off-by: Richard Genoud <richard.genoud@bootlin.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com> Reviewed-by: João Marcos Costa <joaomarcos.costa@bootlin.com>
Richard Genoud [Fri, 13 Mar 2026 10:42:24 +0000 (11:42 +0100)]
fs/squashfs: sqfs_decompressor: simplify code
Switch to if (CONFIG_IS_ENABLED()) instead of #if when possible and
remove unnecessary cases.
Signed-off-by: Richard Genoud <richard.genoud@bootlin.com> Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com> Reviewed-by: João Marcos Costa <joaomarcos.costa@bootlin.com>
Richard Genoud [Fri, 13 Mar 2026 10:42:23 +0000 (11:42 +0100)]
fs/squashfs: fix sqfs_decompressor.c build in SPL
CONFIG_IS_ENABLED() must be used in place of IS_ENABLED() for config
options that have a _SPL_ counterpart.
Signed-off-by: Richard Genoud <richard.genoud@bootlin.com> Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com> Reviewed-by: João Marcos Costa <joaomarcos.costa@bootlin.com>
Add a new fwumdata tool to allows users to read, display, and modify FWU
(Firmware Update) metadata from Linux userspace. It provides
functionality similar to fw_printenv/fw_setenv but for FWU metadata.
Users can view metadata, change active/previous bank indices, modify
bank states, and set image acceptance flags. Configuration is done via
fwumdata.config file.
Peter Robinson [Fri, 13 Mar 2026 17:08:36 +0000 (17:08 +0000)]
rpi: Update the naming for bcm2712 SoC RevD naming
The downstream Raspberry Pi uses two namings for the revD
SoC device trees, both bcm2712d0-rpi-5-b and bcm2712-d-rpi-5-b
but it seems upstream has settled on just the later, so lets
use that as it's the name that maps both upstream and downstream.
Fixes: c15a7919725 ("board/raspberrypi: add bcm2712d0-rpi-5-b for Raspberry Pi 5") Signed-off-by: Peter Robinson <pbrobinson@gmail.com> Reviewed-by: Matthias Brugger <mbrugger@suse.com>
Marek Vasut [Sun, 15 Mar 2026 23:58:06 +0000 (00:58 +0100)]
arm: bcm: Include missing errno.h
The msg.c file uses EIO macro defined in errno.h , include errno.h
to avoid build failure:
"
arch/arm/mach-bcm283x/msg.c: In function 'bcm2835_power_on_module':
arch/arm/mach-bcm283x/msg.c:73:25: error: 'EIO' undeclared (first use in this function)
73 | return -EIO;
| ^~~
"
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Kory Maincent [Mon, 23 Feb 2026 13:18:40 +0000 (14:18 +0100)]
tools: mkfwumdata: Remove dependency on fwu_mdata.h header
The dependency on fwu_mdata.h creates unnecessary configuration
requirements. To generate metadata V1, CONFIG_FWU_MDATA_V1 must be
enabled, which in turn requires enabling FWU_MULTI_BANK_UPDATE,
EFI_CAPSULE_ON_DISK, PARTITION_TYPE_GUID, and other unrelated configs.
This is not suitable for a simple standalone tool.
Additionally, even with the "-v 1" option to generate V1 metadata, the
tool will still include the firmware store description if
CONFIG_FWU_MDATA_V1 is not enabled. This structure should only be
present in metadata V2.
Replace the fwu_mdata.h dependency with the new fwumdata header to make
the tool compatible with both V1 and V2 without requiring any defconfig
changes. This also uses the access helper functions from the header to
eliminate code duplication.
Kory Maincent [Mon, 23 Feb 2026 13:18:39 +0000 (14:18 +0100)]
tools: Add support for fwumdata tool
Add a new fwumdata tool to allows users to read, display, and modify FWU
(Firmware Update) metadata from Linux userspace. It provides functionality
similar to fw_printenv/fw_setenv but for FWU metadata. Users can view
metadata, change active/previous bank indices, modify bank states, and set
image acceptance flags. Configuration is done via fwumdata.config file.
Kory Maincent [Mon, 23 Feb 2026 13:18:38 +0000 (14:18 +0100)]
tools: mkfwumdata: Add bank count validation for FWU metadata v2
The FWU metadata specification version 2 supports a maximum of 4 banks.
Add validation to enforce this limit and prevent creation of non-compliant
metadata structures when using version 2.
Without this check, users could inadvertently create invalid metadata by
specifying more than 4 banks, leading to potential compatibility issues
with FWU-compliant firmware update implementations.
Replace the generic error message with a more informative one.
This helps users quickly understand the correct command-line argument
format when the tool reports an error.
Kory Maincent [Mon, 23 Feb 2026 13:18:36 +0000 (14:18 +0100)]
tools: Reorganize mkfwumdata tool into fwumdata_src directory
Update FWU metadata-related tools by moving mkfwumdata.c into a new
tools/fwumdata_src/ directory structure. This refactoring prepares for the
addition of the fwumdata runtime tool, which will allow editing FWU
metadata directly from the target.
The Kconfig and Makefile entries are also moved into separate files within
the new directory (Kconfig and fwumdata.mk respectively) to keep all FWU
metadata tool configurations together and improve maintainability.
Tom Rini [Wed, 25 Mar 2026 20:38:28 +0000 (14:38 -0600)]
Merge patch series "test/py: gpio: cleanups and improvement"
David Lechner <dlechner@baylibre.com> says:
I wanted to do some quick tests to make sure gpios were working without
having to dig out a schematic. Which means I didn't want to set any GPIO
as an output first without checking. So the main point here is the last
patch which allows gpio_op_pin to be optional and skip the test instead
of failing with exception. This works similar to several other config
options that are already optional in this module.
I also noticed a few easy things to clean up while I was looking at the
file, so there are a couple of extra patches for that.
David Lechner [Thu, 12 Mar 2026 20:33:41 +0000 (15:33 -0500)]
test/py: gpio: allow omitting gpio_op_pin
Modify tests that make use of gpio_op_pin from env__gpio_dev_config to
be skipped if gpio_op_pin is not provided. This is useful in cases where
one might not be sure which GPIOs are safe to use as outputs that can be
toggled without causing problems.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Tom Rini [Wed, 25 Mar 2026 20:38:02 +0000 (14:38 -0600)]
Merge patch series "add [ as alias for test, fix 0/1 argument handling"
Rasmus Villemoes <ravi@prevas.dk> says:
Make 'test' behave a little more like its cousins in other shells, by
allowing the [ ... ] spelling, and while here, fix up the handling of
a single, non-empty argument to comply with POSIX.
Rasmus Villemoes [Thu, 12 Mar 2026 10:01:06 +0000 (11:01 +0100)]
cmd: test: fix handling of single-argument form of test
POSIX states that
0 arguments:
Exit false (1).
1 argument:
Exit true (0) if $1 is not null; otherwise, exit false.
and at least bash and busybox sh behave that way.
The current 'argc < 3' does the right thing for a non-existing or
empty argv[1], but not for a non-empty argv[1]. Fix that and add
corresponding test cases.
Rasmus Villemoes [Thu, 12 Mar 2026 10:01:05 +0000 (11:01 +0100)]
test: add tests for left-bracket alias for 'test' command
Duplicate a few of the existing test cases, using the [ spelling, and
also ensure that the presence of a matching ] as a separate and last
argument is enforced.
Rasmus Villemoes [Thu, 12 Mar 2026 10:01:03 +0000 (11:01 +0100)]
cmd: test: allow using [ as alias for test
I often find myself writing something like
if [ "$somevar" = 123 ] ; then ...
only to realize that that syntax doesn't work in U-Boot shell, and
must be spelled
if test "$somevar" = 123 ; then
It only takes a few lines of code to support this POSIX-standardized
alias for test, and helps developers focus on their actual problems
instead of dealing with such unexpected quirks of the shell.
Anshul Dalal [Thu, 12 Mar 2026 12:04:17 +0000 (17:34 +0530)]
mach-k3: move k3_falcon_fdt_fixup out of r5/common.c
k3_falcon_fdt_fixup is used to perform fdt fixups at runtime in falcon
mode such as adding bootargs. Currently the function is only accessible
to the R5 SPL but could be useful for A53 SPL based falcon mode setups
as well.
Therefore this patch moves the function from r5/common.c to common.c.
Anshul Dalal [Thu, 12 Mar 2026 03:43:24 +0000 (09:13 +0530)]
arm: mach-k3: use Kconfig options for ATF/OPTEE size
The reserved memory sizes for ATF and OPTEE were hard-coded for K3
devices, this patch replaces them with a Kconfig option allowing for
easier modifications.
Acked-by: Andrew Davis <afd@ti.com> Reviewed-by: Dhruva Gole <d-gole@ti.com> Reviewed-by: Manorit Chawdhry <m-chawdhry@ti.com> Signed-off-by: Anshul Dalal <anshuld@ti.com> Reviewed-by: Bryan Brattlof <bb@ti.com>
Tom Rini [Tue, 10 Mar 2026 16:26:10 +0000 (10:26 -0600)]
fw_loader: Introduce SUPPORTS_FW_LOADER symbol
The implementation of FW_LOADER requires CMDLINE to be enabled, and
expressses this. In order to not have to have every users also depends
on CMDLINE introduce SUPPORTS_FW_LOADER. This depends on CMDLINE and
ENV_SUPPORT and then we have all users depends on SUPPORTS_FW_LOADER.
In cases where phys_addr_t/phys_size_t is being printed, it's possible to
use tiny-printf-friendly %pap instead of %llx. For instance, in SPL, with
tiny-printf:
Before the patch:
fdtdec_setup_memory_banksize: DRAM Bank #0: start = 0xx, size = 0xx
After the patch:
fdtdec_setup_memory_banksize: DRAM Bank #0: start = 80000000, size = 40000000
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@siemens.com>
The virtio spec clearly states in "3.1.1 Driver Requirements: Device
Initialization" the sequence a client has to follow after device reset.
Because u-boot resets here again, it also needs to set the "acknowledge"
bit again even if this was done in virtio_uclass_child_post_bind already
once before.
Signed-off-by: Christian Pötzsch <christian.poetzsch@kernkonzept.com> Signed-off-by: Adam Lackorzynski <adam@l4re.org>
[trini: Add VIRTIO_CONFIG_S_ACKNOWLEDGE flag check to the test] Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Wed, 25 Mar 2026 20:32:42 +0000 (14:32 -0600)]
Merge patch series "virtio: rng: Handle oversized return buffers"
Meet Patel <meet.patel2@arm.com> says:
The virtio-rng test to verify effective handling of oversized return
buffers checks that an (undocumented) error is raised, instead of the
real concern, which is the surrounding buffer integrity following a rng
function call.
Update the test to check that the other contents of a buffer remain
unchanged instead of looking for an error code.
The virtio-rng test to verify effective handling of oversized return
buffers checks that an (undocumented) error is raised, instead of the
real concern, which is the surrounding buffer integrity following a rng
function call.
Update the test to check that the other contents of a buffer remain
unchanged instead of looking for an error code.
Tom Rini [Wed, 25 Mar 2026 17:09:08 +0000 (11:09 -0600)]
Merge tag 'mediatek-for-next-2026-03-24' of https://source.denx.de/u-boot/custodians/u-boot-mediatek into next
- MAINTAINERS patch for new MediaTek custodians
- MediaTek pinctrl fix to allow using GPIOs on recent platforms
- The rest is a second wave of MediaTek clock refactoring to remove
duplicate ways of doing the same thing.
Julien Stephan [Thu, 12 Mar 2026 16:19:26 +0000 (17:19 +0100)]
pinctrl: mediatek: Add missing bind callback for several SoCs
Commit f4df9f53b7a9 ("pinctrl: mediatek: Bind gpio while binding pinctrl")
refactored pinctrl-mtk-common.c and the SoC-specific drivers to register
the gpiochip during the bind phase instead of probe. As part of this
change, each SoC driver must implement a bind callback.
The drivers recently added for mt8188, mt8189, mt8195 and mt8365 do not
define this callback, which prevents the gpiochip from being registered
properly.
David Lechner [Wed, 11 Mar 2026 14:52:49 +0000 (09:52 -0500)]
MAINTAINERS: add new MediaTek custodians
Add new MediaTek custodians and the new MediaTek custodian's git
repository to the MAINTAINERS file.
Julien and I have volunteered to act as custodians for MediaTek since
we have been actively working on upstreaming MediaTek support for some
some time now.
projects / thirdparty / u-boot.git / log
