mediatek: filogic: Add support for Wavlink WL-WN551X3

Hardware
--------
- SOC: MediaTek MT7981B
- RAM: 256MB DDR3
- FLASH: 128MB SPI-NAND WinBond W25N01GVZEIG
- NETWORK: 2x1Gb Lan 1x1Gb Wan
- WIFI: MediaTek MT7981B 2x2 DBDC 802.11ax 2T2R (2.4/5)
- LEDs: 3x WAN/LAN (green) 2x STATUS (red/blue)
- USB: 1x XHCI

Installation via Webinterface
-----------------------------

1. Rename OpenWrt sysupgrade bin to wavlink_wl-wn551X3-squashfs-sysupgrade.bin
   The uppercase chars 551X3 are essential and checked by web interface.
2. Logon to webinterface
3. Go to network configuration -> mode selection
4. Choose mode "LAN bridge/access point"
5. Save configuration (maybe network reconfig needed)
6. Go to system upgrade
7. Choose local upgrade and provide renamed sysupgrade file
8. Start upgrade and wait for completion
9. Logon to OpenWrt (network config is preserved during upgrade)

Boot initramfs via TFTP & console
---------------------------------

1. Connect switch to network via LAN1 or LAN2
2. Power on switch
3. Press ESC until prompt reached "MT7981>"
4. Set own IP "setenv ipaddr 192.168.x.y"
5. Set TFTP IP "setenv serverip 192.168.a.b"
6. Set memory address "setenv loadaddr 0x46000000"
7. Download image "tftpboot openwrt-mediatek-filogic-wavlink_wl-wn551x3-initramfs.itb"
8. Boot image "bootm"

Notes
-----

- The red/blue LEDs give a background illumination to the top of the
  case. The red LED is totally disabled to avoid noisy blinking.

- Aside from the design and the different LED colors & placements
  the hardware and partitioning  matches the WAVLINK WL-WN586X3 Rev B.
  Therefor a common DTSI was prepared.

MAC Addresses (same as stock)
-----------------------------

LAN   : 80:3F:5D:xx:xx:B1 (hw, 0x44e(text))
WAN   : 80:3F:5D:xx:xx:B2 (hw, 0x460(text))
2.4GHz: 80:3F:5D:xx:xx:B1 (Factory, 0x4 (hex))
5GHz  : driver auto generated

Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/19515
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

diff --git a/target/linux/mediatek/dts/mt7981b-wavlink-wl-3port-128nand-common.dtsi b/target/linux/mediatek/dts/mt7981b-wavlink-wl-3port-128nand-common.dtsi
new file mode 100644 (file)
index 0000000..f796a00
--- /dev/null
+++ b/target/linux/mediatek/dts/mt7981b-wavlink-wl-3port-128nand-common.dtsi
@@ -0,0 +1,210 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+
+/dts-v1/;
+
+#include "mt7981b.dtsi"
+
+/ {
+       chosen {
+               stdout-path = "serial0:115200n8";
+       };
+
+       gpio-keys {
+               compatible = "gpio-keys";
+
+               button-reset {
+                       label = "reset";
+                       linux,code = <KEY_RESTART>;
+                       gpios = <&pio 11 GPIO_ACTIVE_LOW>;
+               };
+       };
+};
+
+&uart0 {
+       status = "okay";
+};
+
+&watchdog {
+       status = "okay";
+};
+
+&pio {
+       spi0_flash_pins: spi0-pins {
+               mux {
+                       function = "spi";
+                       groups = "spi0", "spi0_wp_hold";
+               };
+
+               conf-pu {
+                       pins = "SPI0_CS", "SPI0_HOLD", "SPI0_WP";
+                       drive-strength = <8>;
+                       bias-pull-up = <103>;
+               };
+
+               conf-pd {
+                       pins = "SPI0_CLK", "SPI0_MOSI", "SPI0_MISO";
+                       drive-strength = <8>;
+                       bias-pull-down = <103>;
+               };
+       };
+};
+
+&spi0 {
+       pinctrl-names = "default";
+       pinctrl-0 = <&spi0_flash_pins>;
+       status = "okay";
+
+       flash@0 {
+               #address-cells = <1>;
+               #size-cells = <1>;
+
+               compatible = "spi-nand";
+               reg = <0>;
+
+               spi-max-frequency = <52000000>;
+               spi-tx-bus-width = <4>;
+               spi-rx-bus-width = <4>;
+
+               partitions {
+                       compatible = "fixed-partitions";
+                       #address-cells = <1>;
+                       #size-cells = <1>;
+
+                       partition@0 {
+                               label = "bl2";
+                               reg = <0x0 0x100000>;
+                               read-only;
+                       };
+
+                       partition@100000 {
+                               label = "u-boot-env";
+                               reg = <0x100000 0x80000>;
+                               read-only;
+                       };
+
+                       factory: partition@180000 {
+                               label = "factory";
+                               reg = <0x180000 0x200000>;
+                               read-only;
+
+                               nvmem-layout {
+                                       compatible = "fixed-layout";
+                                       #address-cells = <1>;
+                                       #size-cells = <1>;
+                                       
+                                       eeprom_factory: eeprom@0 {
+                                               reg = <0x0 0x1000>;
+                                       };                                      
+
+                                       macaddr_factory_4: macaddr@4 {
+                                               reg = <0x4 0x6>;
+                                       };
+                               };
+                       };
+
+                       partition@380000 {
+                               label = "fip";
+                               reg = <0x380000 0x200000>;
+                               read-only;
+                       };
+
+                       partition@580000 {
+                               label = "ubi";
+                               reg = <0x580000 0x4000000>;
+                       };
+
+                       partition@4580000 {
+                               label = "hw";
+                               reg = <0x4580000 0x80000>;
+
+                               nvmem-layout {
+                                       compatible = "fixed-layout";
+                                       #address-cells = <1>;
+                                       #size-cells = <1>;
+
+                                       macaddr_hw_44e: macaddr@44e {
+                                               compatible = "mac-base";
+                                               reg = <0x44e 0x11>;
+                                               #nvmem-cell-cells = <1>;
+                                       };
+                               };
+                       };
+               };
+       };
+};
+
+&eth {
+       status = "okay";
+
+       gmac0: mac@0 {
+               compatible = "mediatek,eth-mac";
+               reg = <0>;
+               phy-mode = "2500base-x";
+
+               nvmem-cell-names = "mac-address";
+               nvmem-cells = <&macaddr_hw_44e 0>;
+
+               fixed-link {
+                       speed = <2500>;
+                       full-duplex;
+                       pause;
+               };
+       };
+
+       gmac1: mac@1 {
+               compatible = "mediatek,eth-mac";
+               reg = <1>;
+               phy-mode = "gmii";
+               phy-handle = <&int_gbe_phy>;
+
+               nvmem-cell-names = "mac-address";
+               nvmem-cells = <&macaddr_hw_44e 1>;
+       };
+};
+
+&mdio_bus {
+       switch: switch@1f {
+               compatible = "mediatek,mt7531";
+               reg = <31>;
+               reset-gpios = <&pio 39 GPIO_ACTIVE_HIGH>;
+               interrupt-controller;
+               #interrupt-cells = <1>;
+               interrupt-parent = <&pio>;
+               interrupts = <38 IRQ_TYPE_LEVEL_HIGH>;
+       };
+};
+
+&switch {
+       ports {
+               #address-cells = <1>;
+               #size-cells = <0>;
+
+               port@1 {
+                       reg = <1>;
+                       label = "lan2";
+               };
+
+               port@2 {
+                       reg = <2>;
+                       label = "lan1";
+               };
+
+               port@6 {
+                       reg = <6>;
+                       ethernet = <&gmac0>;
+                       phy-mode = "2500base-x";
+
+                       fixed-link {
+                               speed = <2500>;
+                               full-duplex;
+                               pause;
+                       };
+               };
+       };
+};
+
+&wifi {
+       status = "okay";
+       nvmem-cells = <&eeprom_factory 0>;
+       nvmem-cell-names = "eeprom";
+};

diff --git a/target/linux/mediatek/dts/mt7981b-wavlink-wl-wn551x3.dts b/target/linux/mediatek/dts/mt7981b-wavlink-wl-wn551x3.dts
new file mode 100644 (file)
index 0000000..0387c73
--- /dev/null
+++ b/target/linux/mediatek/dts/mt7981b-wavlink-wl-wn551x3.dts
@@ -0,0 +1,63 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+
+/dts-v1/;
+
+#include "mt7981b-wavlink-wl-3port-128nand-common.dtsi"
+
+/ {
+       model = "WAVLINK WL-WN551X3";
+       compatible = "wavlink,wl-wn551x3", "mediatek,mt7981b";
+
+       aliases {
+               label-mac-device = &wifi;
+               led-boot = &led_status_blue;
+               led-failsafe = &led_status_blue;
+               led-running = &led_status_blue;
+               led-upgrade = &led_status_blue;
+               serial0 = &uart0;
+       };
+
+       leds {
+               compatible = "gpio-leds";
+
+               led_status_blue: led-0 {
+                       color = <LED_COLOR_ID_BLUE>;
+                       function = LED_FUNCTION_STATUS;
+                       gpios = <&pio 7 GPIO_ACTIVE_HIGH>;
+               };
+
+               led-1 {
+                       color = <LED_COLOR_ID_RED>;
+                       gpios = <&pio 8 GPIO_ACTIVE_HIGH>;
+                       linux,default-trigger = "none";
+               };
+
+               led-2 {
+                       color = <LED_COLOR_ID_GREEN>;
+                       function = LED_FUNCTION_LAN;
+                       function-enumerator = <1>;
+                       gpios = <&pio 10 GPIO_ACTIVE_LOW>;
+               };
+
+               led-3 {
+                       color = <LED_COLOR_ID_GREEN>;
+                       function = LED_FUNCTION_LAN;
+                       function-enumerator = <2>;
+                       gpios = <&pio 9 GPIO_ACTIVE_LOW>;
+               };
+
+               led-4 {
+                       color = <LED_COLOR_ID_GREEN>;
+                       function = LED_FUNCTION_WAN;
+                       gpios = <&pio 25 GPIO_ACTIVE_LOW>;
+               };
+       };
+};
+
+&usb_phy {
+        status = "okay";
+};
+
+&xhci {
+        status = "okay";
+};

diff --git a/target/linux/mediatek/filogic/base-files/etc/board.d/01_leds b/target/linux/mediatek/filogic/base-files/etc/board.d/01_leds
index 6d4c7903bc3263459c07c01eea1cfb35b3f32042..62a01612862b31b08d6556fd203b4d43e62438a0 100644 (file)
--- a/target/linux/mediatek/filogic/base-files/etc/board.d/01_leds
+++ b/target/linux/mediatek/filogic/base-files/etc/board.d/01_leds
@@ -206,6 +206,11 @@ tplink,re6000xd)
        ucidef_set_led_netdev "lan-2" "lan-2" "blue:lan-1" "lan2" "link tx rx"
        ucidef_set_led_netdev "eth1" "lan-3" "blue:lan-2" "eth1" "link tx rx"
        ;;
+wavlink,wl-wn551x3)
+        ucidef_set_led_netdev "lan-1" "lan-1" "green:lan-1" "lan1" "link tx rx"
+        ucidef_set_led_netdev "lan-2" "lan-2" "green:lan-2" "lan2" "link tx rx"
+        ucidef_set_led_netdev "wan" "wan" "green:wan" "eth1" "link tx rx"
+        ;;
 wavlink,wl-wn586x3)
        ucidef_set_led_netdev "lan-1" "lan-1" "blue:lan-1" "lan1" "link tx rx"
        ucidef_set_led_netdev "lan-2" "lan-2" "blue:lan-2" "lan2" "link tx rx"

diff --git a/target/linux/mediatek/filogic/base-files/etc/board.d/02_network b/target/linux/mediatek/filogic/base-files/etc/board.d/02_network
index 802df4608cfca5e19f5ba6b7eeffacb70650d346..1f9d3c551cbc101853c3d3b9d65e5cf31e527217 100644 (file)
--- a/target/linux/mediatek/filogic/base-files/etc/board.d/02_network
+++ b/target/linux/mediatek/filogic/base-files/etc/board.d/02_network
@@ -139,6 +139,7 @@ mediatek_setup_interfaces()
                ucidef_set_interfaces_lan_wan "port1 port3 port4 port5 port6" "port2"
                ;;
        tplink,tl-xdr6086|\
+       wavlink,wl-wn551x3|\
        wavlink,wl-wn586x3)
                ucidef_set_interfaces_lan_wan "lan1 lan2" eth1
                ;;

diff --git a/target/linux/mediatek/image/filogic.mk b/target/linux/mediatek/image/filogic.mk
index e9e74efa1f5fcb0dc4eea7449d9b8d855516d7cf..2e03bb8e7ebaad43674e0479d53dbba4cd7062fe 100644 (file)
--- a/target/linux/mediatek/image/filogic.mk
+++ b/target/linux/mediatek/image/filogic.mk
@@ -1972,6 +1972,24 @@ define Device/unielec_u7981-01-nand
 endef
 TARGET_DEVICES += unielec_u7981-01-nand
 
+define Device/wavlink_wl-wn551x3
+  DEVICE_VENDOR := WAVLINK
+  DEVICE_MODEL := WL-WN551X3
+  DEVICE_DTS := mt7981b-wavlink-wl-wn551x3
+  DEVICE_DTS_DIR := ../dts
+  DEVICE_DTS_LOADADDR := 0x47000000
+  UBINIZE_OPTS := -E 5
+  BLOCKSIZE := 128k
+  PAGESIZE := 2048
+  IMAGE_SIZE := 65536k
+  KERNEL_INITRAMFS_SUFFIX := .itb
+  KERNEL_IN_UBI := 1
+  DEVICE_PACKAGES := kmod-usb3 kmod-mt7915e kmod-mt7981-firmware mt7981-wo-firmware
+  SUPPORTED_DEVICES += mediatek,mt7981-spim-snand-rfb
+  IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
+endef
+TARGET_DEVICES += wavlink_wl-wn551x3
+
 define Device/wavlink_wl-wn586x3
   DEVICE_VENDOR := WAVLINK
   DEVICE_MODEL := WL-WN586X3